Merge branch 'devel-stable' into devel

Conflicts:
	MAINTAINERS
	arch/arm/mm/fault.c

85 files changed, 3632 insertions, 262 deletions

diff --git a/drivers/net/8139too.c b/drivers/net/8139too.c
index 8ae72ec1445..0e2ba21d444 100644
--- a/drivers/net/8139too.c
+++ b/drivers/net/8139too.c
@@ -908,6 +908,7 @@ static const struct net_device_ops rtl8139_netdev_ops = {
 	.ndo_open		= rtl8139_open,
 	.ndo_stop		= rtl8139_close,
 	.ndo_get_stats		= rtl8139_get_stats,
+	.ndo_change_mtu		= eth_change_mtu,
 	.ndo_validate_addr	= eth_validate_addr,
 	.ndo_set_mac_address 	= rtl8139_set_mac_address,
 	.ndo_start_xmit		= rtl8139_start_xmit,
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index f053ba5c37b..3ed49f1337c 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1729,6 +1729,13 @@ config KS8842
 	help
 	  This platform driver is for Micrel KSZ8842 chip.
 
+config KS8851
+       tristate "Micrel KS8851 SPI"
+       depends on SPI
+       select MII
+       help
+         SPI driver for Micrel KS8851 SPI attached network chip.
+
 config VIA_RHINE
 	tristate "VIA Rhine support"
 	depends on NET_PCI && PCI
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 4b58a59f211..ead8cab3cfe 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -88,6 +88,7 @@ obj-$(CONFIG_SKGE) += skge.o
 obj-$(CONFIG_SKY2) += sky2.o
 obj-$(CONFIG_SKFP) += skfp/
 obj-$(CONFIG_KS8842)	+= ks8842.o
+obj-$(CONFIG_KS8851)	+= ks8851.o
 obj-$(CONFIG_VIA_RHINE) += via-rhine.o
 obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o
 obj-$(CONFIG_ADAPTEC_STARFIRE) += starfire.o
diff --git a/drivers/net/arm/Kconfig b/drivers/net/arm/Kconfig
index 2895db13bfa..c37ee9e6b67 100644
--- a/drivers/net/arm/Kconfig
+++ b/drivers/net/arm/Kconfig
@@ -63,3 +63,11 @@ config IXP4XX_ETH
 	help
 	  Say Y here if you want to use built-in Ethernet ports
 	  on IXP4xx processor.
+
+config W90P910_ETH
+	tristate "Nuvoton w90p910 Ethernet support"
+	depends on ARM && ARCH_W90X900
+	select PHYLIB
+	help
+	  Say Y here if you want to use built-in Ethernet ports
+	  on w90p910 processor.
diff --git a/drivers/net/arm/Makefile b/drivers/net/arm/Makefile
index 811a3ccd14c..303171f589e 100644
--- a/drivers/net/arm/Makefile
+++ b/drivers/net/arm/Makefile
@@ -11,3 +11,4 @@ obj-$(CONFIG_ARM_AT91_ETHER)	+= at91_ether.o
 obj-$(CONFIG_ARM_KS8695_ETHER)	+= ks8695net.o
 obj-$(CONFIG_EP93XX_ETH)	+= ep93xx_eth.o
 obj-$(CONFIG_IXP4XX_ETH)	+= ixp4xx_eth.o
+obj-$(CONFIG_W90P910_ETH)	+= w90p910_ether.o
diff --git a/drivers/net/arm/at91_ether.c b/drivers/net/arm/at91_ether.c
index 2e7419a6119..5041d10bae9 100644
--- a/drivers/net/arm/at91_ether.c
+++ b/drivers/net/arm/at91_ether.c
@@ -1228,7 +1228,6 @@ static int at91ether_resume(struct platform_device *pdev)
 #endif
 
 static struct platform_driver at91ether_driver = {
-	.probe		= at91ether_probe,
 	.remove		= __devexit_p(at91ether_remove),
 	.suspend	= at91ether_suspend,
 	.resume		= at91ether_resume,
@@ -1240,7 +1239,7 @@ static struct platform_driver at91ether_driver = {
 
 static int __init at91ether_init(void)
 {
-	return platform_driver_register(&at91ether_driver);
+	return platform_driver_probe(&at91ether_driver, at91ether_probe);
 }
 
 static void __exit at91ether_exit(void)
diff --git a/drivers/net/arm/ixp4xx_eth.c b/drivers/net/arm/ixp4xx_eth.c
index 6f42ad72891..3fe09876e76 100644
--- a/drivers/net/arm/ixp4xx_eth.c
+++ b/drivers/net/arm/ixp4xx_eth.c
@@ -1142,7 +1142,9 @@ static const struct net_device_ops ixp4xx_netdev_ops = {
 	.ndo_start_xmit = eth_xmit,
 	.ndo_set_multicast_list = eth_set_mcast_list,
 	.ndo_do_ioctl = eth_ioctl,
-
+	.ndo_change_mtu = eth_change_mtu,
+	.ndo_set_mac_address = eth_mac_addr,
+	.ndo_validate_addr = eth_validate_addr,
 };
 
 static int __devinit eth_init_one(struct platform_device *pdev)
diff --git a/drivers/net/arm/w90p910_ether.c b/drivers/net/arm/w90p910_ether.c
new file mode 100644
index 00000000000..616fb7985a3
--- /dev/null
+++ b/drivers/net/arm/w90p910_ether.c
@@ -0,0 +1,1105 @@
+/*
+ * Copyright (c) 2008-2009 Nuvoton technology corporation.
+ *
+ * Wan ZongShun <mcuos.com@gmail.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation;version 2 of the License.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/mii.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/ethtool.h>
+#include <linux/platform_device.h>
+#include <linux/clk.h>
+
+#define DRV_MODULE_NAME		"w90p910-emc"
+#define DRV_MODULE_VERSION	"0.1"
+
+/* Ethernet MAC Registers */
+#define REG_CAMCMR		0x00
+#define REG_CAMEN		0x04
+#define REG_CAMM_BASE		0x08
+#define REG_CAML_BASE		0x0c
+#define REG_TXDLSA		0x88
+#define REG_RXDLSA		0x8C
+#define REG_MCMDR		0x90
+#define REG_MIID		0x94
+#define REG_MIIDA		0x98
+#define REG_FFTCR		0x9C
+#define REG_TSDR		0xa0
+#define REG_RSDR		0xa4
+#define REG_DMARFC		0xa8
+#define REG_MIEN		0xac
+#define REG_MISTA		0xb0
+#define REG_CTXDSA		0xcc
+#define REG_CTXBSA		0xd0
+#define REG_CRXDSA		0xd4
+#define REG_CRXBSA		0xd8
+
+/* mac controller bit */
+#define MCMDR_RXON		0x01
+#define MCMDR_ACP		(0x01 << 3)
+#define MCMDR_SPCRC		(0x01 << 5)
+#define MCMDR_TXON		(0x01 << 8)
+#define MCMDR_FDUP		(0x01 << 18)
+#define MCMDR_ENMDC		(0x01 << 19)
+#define MCMDR_OPMOD		(0x01 << 20)
+#define SWR			(0x01 << 24)
+
+/* cam command regiser */
+#define CAMCMR_AUP		0x01
+#define CAMCMR_AMP		(0x01 << 1)
+#define CAMCMR_ABP		(0x01 << 2)
+#define CAMCMR_CCAM		(0x01 << 3)
+#define CAMCMR_ECMP		(0x01 << 4)
+#define CAM0EN			0x01
+
+/* mac mii controller bit */
+#define MDCCR			(0x0a << 20)
+#define PHYAD			(0x01 << 8)
+#define PHYWR			(0x01 << 16)
+#define PHYBUSY			(0x01 << 17)
+#define PHYPRESP		(0x01 << 18)
+#define CAM_ENTRY_SIZE		0x08
+
+/* rx and tx status */
+#define TXDS_TXCP		(0x01 << 19)
+#define RXDS_CRCE		(0x01 << 17)
+#define RXDS_PTLE		(0x01 << 19)
+#define RXDS_RXGD		(0x01 << 20)
+#define RXDS_ALIE		(0x01 << 21)
+#define RXDS_RP			(0x01 << 22)
+
+/* mac interrupt status*/
+#define MISTA_EXDEF		(0x01 << 19)
+#define MISTA_TXBERR		(0x01 << 24)
+#define MISTA_TDU		(0x01 << 23)
+#define MISTA_RDU		(0x01 << 10)
+#define MISTA_RXBERR		(0x01 << 11)
+
+#define ENSTART			0x01
+#define ENRXINTR		0x01
+#define ENRXGD			(0x01 << 4)
+#define ENRXBERR		(0x01 << 11)
+#define ENTXINTR		(0x01 << 16)
+#define ENTXCP			(0x01 << 18)
+#define ENTXABT			(0x01 << 21)
+#define ENTXBERR		(0x01 << 24)
+#define ENMDC			(0x01 << 19)
+#define PHYBUSY			(0x01 << 17)
+#define MDCCR_VAL		0xa00000
+
+/* rx and tx owner bit */
+#define RX_OWEN_DMA		(0x01 << 31)
+#define RX_OWEN_CPU		(~(0x03 << 30))
+#define TX_OWEN_DMA		(0x01 << 31)
+#define TX_OWEN_CPU		(~(0x01 << 31))
+
+/* tx frame desc controller bit */
+#define MACTXINTEN		0x04
+#define CRCMODE			0x02
+#define PADDINGMODE		0x01
+
+/* fftcr controller bit */
+#define TXTHD 			(0x03 << 8)
+#define BLENGTH			(0x01 << 20)
+
+/* global setting for driver */
+#define RX_DESC_SIZE		50
+#define TX_DESC_SIZE		10
+#define MAX_RBUFF_SZ		0x600
+#define MAX_TBUFF_SZ		0x600
+#define TX_TIMEOUT		50
+#define DELAY			1000
+#define CAM0			0x0
+
+static int w90p910_mdio_read(struct net_device *dev, int phy_id, int reg);
+
+struct w90p910_rxbd {
+	unsigned int sl;
+	unsigned int buffer;
+	unsigned int reserved;
+	unsigned int next;
+};
+
+struct w90p910_txbd {
+	unsigned int mode;
+	unsigned int buffer;
+	unsigned int sl;
+	unsigned int next;
+};
+
+struct recv_pdesc {
+	struct w90p910_rxbd desclist[RX_DESC_SIZE];
+	char recv_buf[RX_DESC_SIZE][MAX_RBUFF_SZ];
+};
+
+struct tran_pdesc {
+	struct w90p910_txbd desclist[TX_DESC_SIZE];
+	char tran_buf[RX_DESC_SIZE][MAX_TBUFF_SZ];
+};
+
+struct  w90p910_ether {
+	struct recv_pdesc *rdesc;
+	struct recv_pdesc *rdesc_phys;
+	struct tran_pdesc *tdesc;
+	struct tran_pdesc *tdesc_phys;
+	struct net_device_stats stats;
+	struct platform_device *pdev;
+	struct sk_buff *skb;
+	struct clk *clk;
+	struct clk *rmiiclk;
+	struct mii_if_info mii;
+	struct timer_list check_timer;
+	void __iomem *reg;
+	unsigned int rxirq;
+	unsigned int txirq;
+	unsigned int cur_tx;
+	unsigned int cur_rx;
+	unsigned int finish_tx;
+	unsigned int rx_packets;
+	unsigned int rx_bytes;
+	unsigned int start_tx_ptr;
+	unsigned int start_rx_ptr;
+	unsigned int linkflag;
+	spinlock_t lock;
+};
+
+static void update_linkspeed_register(struct net_device *dev,
+				unsigned int speed, unsigned int duplex)
+{
+	struct w90p910_ether *ether = netdev_priv(dev);
+	unsigned int val;
+
+	val = __raw_readl(ether->reg + REG_MCMDR);
+
+	if (speed == SPEED_100) {
+		/* 100 full/half duplex */
+		if (duplex == DUPLEX_FULL) {
+			val |= (MCMDR_OPMOD | MCMDR_FDUP);
+		} else {
+			val |= MCMDR_OPMOD;
+			val &= ~MCMDR_FDUP;
+		}
+	} else {
+		/* 10 full/half duplex */
+		if (duplex == DUPLEX_FULL) {
+			val |= MCMDR_FDUP;
+			val &= ~MCMDR_OPMOD;
+		} else {
+			val &= ~(MCMDR_FDUP | MCMDR_OPMOD);
+		}
+	}
+
+	__raw_writel(val, ether->reg + REG_MCMDR);
+}
+
+static void update_linkspeed(struct net_device *dev)
+{
+	struct w90p910_ether *ether = netdev_priv(dev);
+	struct platform_device *pdev;
+	unsigned int bmsr, bmcr, lpa, speed, duplex;
+
+	pdev = ether->pdev;
+
+	if (!mii_link_ok(&ether->mii)) {
+		ether->linkflag = 0x0;
+		netif_carrier_off(dev);
+		dev_warn(&pdev->dev, "%s: Link down.\n", dev->name);
+		return;
+	}
+
+	if (ether->linkflag == 1)
+		return;
+
+	bmsr = w90p910_mdio_read(dev, ether->mii.phy_id, MII_BMSR);
+	bmcr = w90p910_mdio_read(dev, ether->mii.phy_id, MII_BMCR);
+
+	if (bmcr & BMCR_ANENABLE) {
+		if (!(bmsr & BMSR_ANEGCOMPLETE))
+			return;
+
+		lpa = w90p910_mdio_read(dev, ether->mii.phy_id, MII_LPA);
+
+		if ((lpa & LPA_100FULL) || (lpa & LPA_100HALF))
+			speed = SPEED_100;
+		else
+			speed = SPEED_10;
+
+		if ((lpa & LPA_100FULL) || (lpa & LPA_10FULL))
+			duplex = DUPLEX_FULL;
+		else
+			duplex = DUPLEX_HALF;
+
+	} else {
+		speed = (bmcr & BMCR_SPEED100) ? SPEED_100 : SPEED_10;
+		duplex = (bmcr & BMCR_FULLDPLX) ? DUPLEX_FULL : DUPLEX_HALF;
+	}
+
+	update_linkspeed_register(dev, speed, duplex);
+
+	dev_info(&pdev->dev, "%s: Link now %i-%s\n", dev->name, speed,
+			(duplex == DUPLEX_FULL) ? "FullDuplex" : "HalfDuplex");
+	ether->linkflag = 0x01;
+
+	netif_carrier_on(dev);
+}
+
+static void w90p910_check_link(unsigned long dev_id)
+{
+	struct net_device *dev = (struct net_device *) dev_id;
+	struct w90p910_ether *ether = netdev_priv(dev);
+
+	update_linkspeed(dev);
+	mod_timer(&ether->check_timer, jiffies + msecs_to_jiffies(1000));
+}
+
+static void w90p910_write_cam(struct net_device *dev,
+				unsigned int x, unsigned char *pval)
+{
+	struct w90p910_ether *ether = netdev_priv(dev);
+	unsigned int msw, lsw;
+
+	msw = (pval[0] << 24) | (pval[1] << 16) | (pval[2] << 8) | pval[3];
+
+	lsw = (pval[4] << 24) | (pval[5] << 16);
+
+	__raw_writel(lsw, ether->reg + REG_CAML_BASE + x * CAM_ENTRY_SIZE);
+	__raw_writel(msw, ether->reg + REG_CAMM_BASE + x * CAM_ENTRY_SIZE);
+}
+
+static void w90p910_init_desc(struct net_device *dev)
+{
+	struct w90p910_ether *ether;
+	struct w90p910_txbd  *tdesc, *tdesc_phys;
+	struct w90p910_rxbd  *rdesc, *rdesc_phys;
+	unsigned int i, j;
+
+	ether = netdev_priv(dev);
+
+	ether->tdesc = (struct tran_pdesc *)
+			dma_alloc_coherent(NULL, sizeof(struct tran_pdesc),
+				(dma_addr_t *) &ether->tdesc_phys, GFP_KERNEL);
+
+	ether->rdesc = (struct recv_pdesc *)
+			dma_alloc_coherent(NULL, sizeof(struct recv_pdesc),
+				(dma_addr_t *) &ether->rdesc_phys, GFP_KERNEL);
+
+	for (i = 0; i < TX_DESC_SIZE; i++) {
+		tdesc = &(ether->tdesc->desclist[i]);
+
+		j = ((i + 1) / TX_DESC_SIZE);
+
+		if (j != 0) {
+			tdesc_phys = &(ether->tdesc_phys->desclist[0]);
+			ether->start_tx_ptr = (unsigned int)tdesc_phys;
+			tdesc->next = (unsigned int)ether->start_tx_ptr;
+		} else {
+			tdesc_phys = &(ether->tdesc_phys->desclist[i+1]);
+			tdesc->next = (unsigned int)tdesc_phys;
+		}
+