Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 1785 insertions, 0 deletions

diff --git a/drivers/net/sundance.c b/drivers/net/sundance.c
new file mode 100644
index 00000000000..08cb7177a17
--- /dev/null
+++ b/drivers/net/sundance.c
@@ -0,0 +1,1785 @@
+/* sundance.c: A Linux device driver for the Sundance ST201 "Alta". */
+/*
+	Written 1999-2000 by Donald Becker.
+
+	This software may be used and distributed according to the terms of
+	the GNU General Public License (GPL), incorporated herein by reference.
+	Drivers based on or derived from this code fall under the GPL and must
+	retain the authorship, copyright and license notice.  This file is not
+	a complete program and may only be used when the entire operating
+	system is licensed under the GPL.
+
+	The author may be reached as becker@scyld.com, or C/O
+	Scyld Computing Corporation
+	410 Severn Ave., Suite 210
+	Annapolis MD 21403
+
+	Support and updates available at
+	http://www.scyld.com/network/sundance.html
+
+
+	Version LK1.01a (jgarzik):
+	- Replace some MII-related magic numbers with constants
+
+	Version LK1.02 (D-Link):
+	- Add new board to PCI ID list
+	- Fix multicast bug
+
+	Version LK1.03 (D-Link):
+	- New Rx scheme, reduce Rx congestion
+	- Option to disable flow control
+
+	Version LK1.04 (D-Link):
+	- Tx timeout recovery
+	- More support for ethtool.
+
+	Version LK1.04a:
+	- Remove unused/constant members from struct pci_id_info
+	(which then allows removal of 'drv_flags' from private struct)
+	(jgarzik)
+	- If no phy is found, fail to load that board (jgarzik)
+	- Always start phy id scan at id 1 to avoid problems (Donald Becker)
+	- Autodetect where mii_preable_required is needed,
+	default to not needed.  (Donald Becker)
+
+	Version LK1.04b:
+	- Remove mii_preamble_required module parameter (Donald Becker)
+	- Add per-interface mii_preamble_required (setting is autodetected)
+	  (Donald Becker)
+	- Remove unnecessary cast from void pointer (jgarzik)
+	- Re-align comments in private struct (jgarzik)
+
+	Version LK1.04c (jgarzik):
+	- Support bitmapped message levels (NETIF_MSG_xxx), and the
+	  two ethtool ioctls that get/set them
+	- Don't hand-code MII ethtool support, use standard API/lib
+
+	Version LK1.04d:
+	- Merge from Donald Becker's sundance.c: (Jason Lunz)
+		* proper support for variably-sized MTUs
+		* default to PIO, to fix chip bugs
+	- Add missing unregister_netdev (Jason Lunz)
+	- Add CONFIG_SUNDANCE_MMIO config option (jgarzik)
+	- Better rx buf size calculation (Donald Becker)
+
+	Version LK1.05 (D-Link):
+	- Fix DFE-580TX packet drop issue (for DL10050C)
+	- Fix reset_tx logic
+
+	Version LK1.06 (D-Link):
+	- Fix crash while unloading driver
+
+	Versin LK1.06b (D-Link):
+	- New tx scheme, adaptive tx_coalesce
+	
+	Version LK1.07 (D-Link):
+	- Fix tx bugs in big-endian machines
+	- Remove unused max_interrupt_work module parameter, the new 
+	  NAPI-like rx scheme doesn't need it.
+	- Remove redundancy get_stats() in intr_handler(), those 
+	  I/O access could affect performance in ARM-based system
+	- Add Linux software VLAN support
+	
+	Version LK1.08 (D-Link):
+	- Fix bug of custom mac address 
+	(StationAddr register only accept word write) 
+
+	Version LK1.09 (D-Link):
+	- Fix the flowctrl bug.	
+	- Set Pause bit in MII ANAR if flow control enabled.	
+
+	Version LK1.09a (ICPlus):
+	- Add the delay time in reading the contents of EEPROM
+
+*/
+
+#define DRV_NAME	"sundance"
+#define DRV_VERSION	"1.01+LK1.09a"
+#define DRV_RELDATE	"10-Jul-2003"
+
+
+/* The user-configurable values.
+   These may be modified when a driver module is loaded.*/
+static int debug = 1;			/* 1 normal messages, 0 quiet .. 7 verbose. */
+/* Maximum number of multicast addresses to filter (vs. rx-all-multicast).
+   Typical is a 64 element hash table based on the Ethernet CRC.  */
+static int multicast_filter_limit = 32;
+
+/* Set the copy breakpoint for the copy-only-tiny-frames scheme.
+   Setting to > 1518 effectively disables this feature.
+   This chip can receive into offset buffers, so the Alpha does not
+   need a copy-align. */
+static int rx_copybreak;
+static int flowctrl=1;
+
+/* media[] specifies the media type the NIC operates at.
+		 autosense	Autosensing active media.
+		 10mbps_hd 	10Mbps half duplex.
+		 10mbps_fd 	10Mbps full duplex.
+		 100mbps_hd 	100Mbps half duplex.
+		 100mbps_fd 	100Mbps full duplex.
+		 0		Autosensing active media.
+		 1	 	10Mbps half duplex.
+		 2	 	10Mbps full duplex.
+		 3	 	100Mbps half duplex.
+		 4	 	100Mbps full duplex.
+*/
+#define MAX_UNITS 8
+static char *media[MAX_UNITS];
+
+
+/* Operational parameters that are set at compile time. */
+
+/* Keep the ring sizes a power of two for compile efficiency.
+   The compiler will convert <unsigned>'%'<2^N> into a bit mask.
+   Making the Tx ring too large decreases the effectiveness of channel
+   bonding and packet priority, and more than 128 requires modifying the
+   Tx error recovery.
+   Large receive rings merely waste memory. */
+#define TX_RING_SIZE	32
+#define TX_QUEUE_LEN	(TX_RING_SIZE - 1) /* Limit ring entries actually used.  */
+#define RX_RING_SIZE	64
+#define RX_BUDGET	32
+#define TX_TOTAL_SIZE	TX_RING_SIZE*sizeof(struct netdev_desc)
+#define RX_TOTAL_SIZE	RX_RING_SIZE*sizeof(struct netdev_desc)
+
+/* Operational parameters that usually are not changed. */
+/* Time in jiffies before concluding the transmitter is hung. */
+#define TX_TIMEOUT  (4*HZ)
+#define PKT_BUF_SZ		1536	/* Size of each temporary Rx buffer.*/
+
+/* Include files, designed to support most kernel versions 2.0.0 and later. */
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/timer.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/init.h>
+#include <linux/bitops.h>
+#include <asm/uaccess.h>
+#include <asm/processor.h>		/* Processor type for cache alignment. */
+#include <asm/io.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#ifndef _COMPAT_WITH_OLD_KERNEL
+#include <linux/crc32.h>
+#include <linux/ethtool.h>
+#include <linux/mii.h>
+#else
+#include "crc32.h"
+#include "ethtool.h"
+#include "mii.h"
+#include "compat.h"
+#endif
+
+/* These identify the driver base version and may not be removed. */
+static char version[] __devinitdata =
+KERN_INFO DRV_NAME ".c:v" DRV_VERSION " " DRV_RELDATE "  Written by Donald Becker\n"
+KERN_INFO "  http://www.scyld.com/network/sundance.html\n";
+
+MODULE_AUTHOR("Donald Becker <becker@scyld.com>");
+MODULE_DESCRIPTION("Sundance Alta Ethernet driver");
+MODULE_LICENSE("GPL");
+
+module_param(debug, int, 0);
+module_param(rx_copybreak, int, 0);
+module_param_array(media, charp, NULL, 0);
+module_param(flowctrl, int, 0);
+MODULE_PARM_DESC(debug, "Sundance Alta debug level (0-5)");
+MODULE_PARM_DESC(rx_copybreak, "Sundance Alta copy breakpoint for copy-only-tiny-frames");
+MODULE_PARM_DESC(flowctrl, "Sundance Alta flow control [0|1]");
+
+/*
+				Theory of Operation
+
+I. Board Compatibility
+
+This driver is designed for the Sundance Technologies "Alta" ST201 chip.
+
+II. Board-specific settings
+
+III. Driver operation
+
+IIIa. Ring buffers
+
+This driver uses two statically allocated fixed-size descriptor lists
+formed into rings by a branch from the final descriptor to the beginning of
+the list.  The ring sizes are set at compile time by RX/TX_RING_SIZE.
+Some chips explicitly use only 2^N sized rings, while others use a
+'next descriptor' pointer that the driver forms into rings.
+
+IIIb/c. Transmit/Receive Structure
+
+This driver uses a zero-copy receive and transmit scheme.
+The driver allocates full frame size skbuffs for the Rx ring buffers at
+open() time and passes the skb->data field to the chip as receive data
+buffers.  When an incoming frame is less than RX_COPYBREAK bytes long,
+a fresh skbuff is allocated and the frame is copied to the new skbuff.
+When the incoming frame is larger, the skbuff is passed directly up the
+protocol stack.  Buffers consumed this way are replaced by newly allocated
+skbuffs in a later phase of receives.
+
+The RX_COPYBREAK value is chosen to trade-off the memory wasted by
+using a full-sized skbuff for small frames vs. the copying costs of larger
+frames.  New boards are typically used in generously configured machines
+and the underfilled buffers have negligible impact compared to the benefit of
+a single allocation size, so the default value of zero results in never
+copying packets.  When copying is done, the cost is usually mitigated by using
+a combined copy/checksum routine.  Copying also preloads the cache, which is
+most useful with small frames.
+
+A subtle aspect of the operation is that the IP header at offset 14 in an
+ethernet frame isn't longword aligned for further processing.
+Unaligned buffers are permitted by the Sundance hardware, so
+frames are received into the skbuff at an offset of "+2", 16-byte aligning
+the IP header.
+
+IIId. Synchronization
+
+The driver runs as two independent, single-threaded flows of control.  One
+is the send-packet routine, which enforces single-threaded use by the
+dev->tbusy flag.  The other thread is the interrupt handler, which is single
+threaded by the hardware and interrupt handling software.
+
+The send packet thread has partial control over the Tx ring and 'dev->tbusy'
+flag.  It sets the tbusy flag whenever it's queuing a Tx packet. If the next
+queue slot is empty, it clears the tbusy flag when finished otherwise it sets
+the 'lp->tx_full' flag.
+
+The interrupt handler has exclusive control over the Rx ring and records stats
+from the Tx ring.  After reaping the stats, it marks the Tx queue entry as
+empty by incrementing the dirty_tx mark. Iff the 'lp->tx_full' flag is set, it
+clears both the tx_full and tbusy flags.
+
+IV. Notes
+
+IVb. References
+
+The Sundance ST201 datasheet, preliminary version.
+http://cesdis.gsfc.nasa.gov/linux/misc/100mbps.html
+http://cesdis.gsfc.nasa.gov/linux/misc/NWay.html
+
+IVc. Errata
+
+*/
+
+/* Work-around for Kendin chip bugs. */
+#ifndef CONFIG_SUNDANCE_MMIO
+#define USE_IO_OPS 1
+#endif
+
+static struct pci_device_id sundance_pci_tbl[] = {
+	{0x1186, 0x1002, 0x1186, 0x1002, 0, 0, 0},
+	{0x1186, 0x1002, 0x1186, 0x1003, 0, 0, 1},
+	{0x1186, 0x1002, 0x1186, 0x1012, 0, 0, 2},
+	{0x1186, 0x1002, 0x1186, 0x1040, 0, 0, 3},
+	{0x1186, 0x1002, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 4},
+	{0x13F0, 0x0201, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 5},
+	{0,}
+};
+MODULE_DEVICE_TABLE(pci, sundance_pci_tbl);
+
+enum {
+	netdev_io_size = 128
+};
+
+struct pci_id_info {
+        const char *name;
+};
+static struct pci_id_info pci_id_tbl[] = {
+	{"D-Link DFE-550TX FAST Ethernet Adapter"},
+	{"D-Link DFE-550FX 100Mbps Fiber-optics Adapter"},
+	{"D-Link DFE-580TX 4 port Server Adapter"},
+	{"D-Link DFE-530TXS FAST Ethernet Adapter"},
+	{"D-Link DL10050-based FAST Ethernet Adapter"},
+	{"Sundance Technology Alta"},
+	{NULL,},			/* 0 terminated list. */
+};
+
+/* This driver was written to use PCI memory space, however x86-oriented
+   hardware often uses I/O space accesses. */
+
+/* Offsets to the device registers.
+   Unlike software-only systems, device drivers interact with complex hardware.
+   It's not useful to define symbolic names for every register bit in the
+   device.  The name can only partially document the semantics and make
+   the driver longer and more difficult to read.
+   In general, only the important configuration values or bits changed
+   multiple times should be defined symbolically.
+*/
+enum alta_offsets {
+	DMACtrl = 0x00,
+	TxListPtr = 0x04,
+	TxDMABurstThresh = 0x08,
+	TxDMAUrgentThresh = 0x09,
+	TxDMAPollPeriod = 0x0a,
+	RxDMAStatus = 0x0c,
+	RxListPtr = 0x10,
+	DebugCtrl0 = 0x1a,
+	DebugCtrl1 = 0x1c,
+	RxDMABurstThresh = 0x14,
+	RxDMAUrgentThresh = 0x15,
+	RxDMAPollPeriod = 0x16,
+	LEDCtrl = 0x1a,
+	ASICCtrl = 0x30,
+	EEData = 0x34,
+	EECtrl = 0x36,
+	TxStartThresh = 0x3c,
+	RxEarlyThresh = 0x3e,
+	FlashAddr = 0x40,
+	FlashData = 0x44,
+	TxStatus = 0x46,
+	TxFrameId = 0x47,
+	DownCounter = 0x18,
+	IntrClear = 0x4a,
+	IntrEnable = 0x4c,
+	IntrStatus = 0x4e,
+	MACCtrl0 = 0x50,
+	MACCtrl1 = 0x52,
+	StationAddr = 0x54,
+	MaxFrameSize = 0x5A,
+	RxMode = 0x5c,
+	MIICtrl = 0x5e,
+	MulticastFilter0 = 0x60,
+	MulticastFilter1 = 0x64,
+	RxOctetsLow = 0x68,
+	RxOctetsHigh = 0x6a,
+	TxOctetsLow = 0x6c,
+	TxOctetsHigh = 0x6e,
+	TxFramesOK = 0x70,
+	RxFramesOK = 0x72,
+	StatsCarrierError = 0x74,
+	StatsLateColl = 0x75,
+	StatsMultiColl = 0x76,
+	StatsOneColl = 0x77,
+	StatsTxDefer = 0x78,
+	RxMissed = 0x79,
+	StatsTxXSDefer = 0x7a,
+	StatsTxAbort = 0x7b,
+	StatsBcastTx = 0x7c,
+	StatsBcastRx = 0x7d,
+	StatsMcastTx = 0x7e,
+	StatsMcastRx = 0x7f,
+	/* Aliased and bogus values! */
+	RxStatus = 0x0c,
+};
+enum ASICCtrl_HiWord_bit {
+	GlobalReset = 0x0001,
+	RxReset = 0x0002,
+	TxReset = 0x0004,
+	DMAReset = 0x0008,
+	FIFOReset = 0x0010,
+	NetworkReset = 0x0020,
+	HostReset = 0x0040,
+	ResetBusy = 0x0400,
+};
+
+/* Bits in the interrupt status/mask registers. */
+enum intr_status_bits {
+	IntrSummary=0x0001, IntrPCIErr=0x0002, IntrMACCtrl=0x0008,
+	IntrTxDone=0x0004, IntrRxDone=0x0010, IntrRxStart=0x0020,
+	IntrDrvRqst=0x0040,
+	StatsMax=0x0080, LinkChange=0x0100,
+	IntrTxDMADone=0x0200, IntrRxDMADone=0x0400,
+};
+
+/* Bits in the RxMode register. */
+enum rx_mode_bits {
+	AcceptAllIPMulti=0x20, AcceptMultiHash=0x10, AcceptAll=0x08,
+	AcceptBroadcast=0x04, AcceptMulticast=0x02, AcceptMyPhys=0x01,
+};
+/* Bits in MACCtrl. */
+enum mac_ctrl0_bits {
+	EnbFullDuplex=0x20, EnbRcvLargeFrame=0x40,
+	EnbFlowCtrl=0x100, EnbPassRxCRC=0x200,
+};
+enum mac_ctrl1_bits {
+	StatsEnable=0x0020,	StatsDisable=0x0040, StatsEnabled=0x0080,
+	TxEnable=0x0100, TxDisable=0x0200, TxEnabled=0x0400,
+	RxEnable=0x0800, RxDisable=0x1000, RxEnabled=0x2000,
+};
+
+/* The Rx and Tx buffer descriptors. */
+/* Note that using only 32 bit fields simplifies conversion to big-endian
+   architectures. */
+struct netdev_desc {
+	u32 next_desc;
+	u32 status;
+	struct desc_frag { u32 addr, length; } frag[1];
+};
+
+/* Bits in netdev_desc.status */
+enum desc_status_bits {
+	DescOwn=0x8000,
+	DescEndPacket=0x4000,
+	DescEndRing=0x2000,
+	LastFrag=0x80000000,
+	DescIntrOnTx=0x8000,
+	DescIntrOnDMADone=0x80000000,
+	DisableAlign = 0x00000001,
+};
+
+#define PRIV_ALIGN	15 	/* Required alignment mask */
+/* Use  __attribute__((aligned (L1_CACHE_BYTES)))  to maintain alignment
+   within the structure. */
+#define MII_CNT		4
+struct netdev_private {
+	/* Descriptor rings first for alignment. */
+	struct netdev_desc *rx_ring;
+	struct netdev_desc *tx_ring;
+	struct sk_buff* rx_skbuff[RX_RING_SIZE];
+	struct sk_buff* tx_skbuff[TX_RING_SIZE];
+        dma_addr_t tx_ring_dma;
+        dma_addr_t rx_ring_dma;
+	struct net_device_stats stats;
+	struct timer_list timer;		/* Media monitoring timer. */
+	/* Frequently used values: keep some adjacent for cache effect. */
+	spinlock_t lock;
+	spinlock_t rx_lock;			/* Group with Tx control cache line. */
+	int msg_enable;
+	int chip_id;
+	unsigned int cur_rx, dirty_rx;		/* Producer/consumer ring indices */
+	unsigned int rx_buf_sz;			/* Based on MTU+slack. */
+	struct netdev_desc *last_tx;		/* Last Tx descriptor used. */
+	unsigned int cur_tx, dirty_tx;
+	/* These values are keep track of the transceiver/media in use. */
+	unsigned int flowctrl:1;
+	unsigned int default_port:4;		/* Last dev->if_port value. */
+	unsigned int an_enable:1;
+	unsigned int speed;
+	struct tasklet_struct rx_tasklet;
+	struct tasklet_struct tx_tasklet;
+	int budget;
+	int cur_task;
+	/* Multicast and receive mode. */
+	spinlock_t mcastlock;			/* SMP lock multicast updates. */
+	u16 mcast_filter[4];
+	/* MII transceiver section. */
+	struct mii_if_info mii_if;
+	int mii_preamble_required;
+	unsigned char phys[MII_CNT];		/* MII device addresses, only first one used. */
+	struct pci_dev *pci_dev;
+	void __iomem *base;
+	unsigned char pci_rev_id;
+};
+
+/* The station address location in the EEPROM. */
+#define EEPROM_SA_OFFSET	0x10
+#define DEFAULT_INTR (IntrRxDMADone | IntrPCIErr | \
+			IntrDrvRqst | IntrTxDone | StatsMax | \
+			LinkChange)
+
+static int  change_mtu(struct net_device *dev, int new_mtu);
+static int  eeprom_read(void __iomem *ioaddr, int location);
+static int  mdio_read(struct net_device *dev, int phy_id, int location);
+static void mdio_write(struct net_device *dev, int phy_id, int location, int value);
+static int  netdev_open(struct net_device *dev);
+static void check_duplex(struct net_device *dev);
+static void netdev_timer(unsigned long data);
+static void tx_timeout(struct net_device *dev);
+static void init_ring(struct net_device *dev);
+static int  start_tx(struct sk_buff *skb, struct net_device *dev);
+static int reset_tx (struct net_device *dev);
+static irqreturn_t intr_handler(int irq, void *dev_instance, struct pt_regs *regs);
+static void rx_poll(unsigned long data);
+static void tx_poll(unsigned long data);
+static void refill_rx (struct net_device *dev);
+static void netdev_error(struct net_device *dev, int intr_status);
+static void netdev_error(struct net_device *dev, int intr_status);
+static void set_rx_mode(struct net_device *dev);
+static int __set_mac_addr(struct net_device *dev);
+static struct net_device_stats *get_stats(struct net_device *dev);
+static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd);
+static int  netdev_close(struct net_device *dev);
+static struct ethtool_ops ethtool_ops;
+
+static int __devinit sundance_probe1 (struct pci_dev *pdev,
+				      const struct pci_device_id *ent)
+{
+	struct net_device *dev;
+	struct netdev_private *np;
+	static int card_idx;
+	int chip_idx = ent->driver_data;
+	int irq;
+	int i;
+	void __iomem *ioaddr;
+	u16 mii_ctl;
+	void *ring_space;
+	dma_addr_t ring_dma;
+#ifdef USE_IO_OPS
+	int bar = 0;
+#else
+	int bar = 1;
+#endif
+
+
+/* when built into the kernel, we only print version if device is found */
+#ifndef MODULE
+	static int printed_version;
+	if (!printed_version++)
+		printk(version);
+#endif
+
+	if (pci_enable_device(pdev))
+		return -EIO;
+	pci_set_master(pdev);
+
+	irq = pdev->irq;
+
+	dev = alloc_etherdev(sizeof(*np));
+	if (!dev)
+		return -ENOMEM;
+	SET_MODULE_OWNER(dev);
+	SET_NETDEV_DEV(dev, &pdev->dev);
+
+	if (pci_request_regions(pdev, DRV_NAME))
+		goto err_out_netdev;
+
+	ioaddr = pci_iomap(pdev, bar, netdev_io_size);
+	if (!ioaddr)
+		goto err_out_res;
+
+	for (i = 0; i < 3; i++)
+		((u16 *)dev->dev_addr)[i] =
+			le16_to_cpu(eeprom_read(ioaddr, i + EEPROM_SA_OFFSET));
+
+	dev->base_addr = (unsigned long)ioaddr;
+	dev->irq = irq;
+
+	np = netdev_priv(dev);
+	np->base = ioaddr;
+	np->pci_dev = pdev;
+	np->chip_id = chip_idx;
+	np->msg_enable = (1 << debug) - 1;
+	spin_lock_init(&np->lock);
+	tasklet_init(&np->rx_tasklet, rx_poll, (unsigned long)dev);
+	tasklet_init(&np->tx_tasklet, tx_poll, (unsigned long)dev);
+
+	ring_space = pci_alloc_consistent(pdev, TX_TOTAL_SIZE, &ring_dma);
+	if (!ring_space)
+		goto err_out_cleardev;
+	np->tx_ring = (struct netdev_desc *)ring_space;
+	np->tx_ring_dma = ring_dma;
+
+	ring_space = pci_alloc_consistent(pdev, RX_TOTAL_SIZE, &ring_dma);
+	if (!ring_space)
+		goto err_out_unmap_tx;
+	np->rx_ring = (struct netdev_desc *)ring_space;
+	np->rx_ring_dma = ring_dma;
+
+	np->mii_if.dev = dev;
+	np->mii_if.mdio_read = mdio_read;
+	np->mii_if.mdio_write = mdio_write;
+	np->mii_if.phy_id_mask = 0x1f;
+	np->mii_if.reg_num_mask = 0x1f;
+
+	/* The chip-specific entries in the device structure. */
+	dev->open = &netdev_open;
+	dev->hard_start_xmit = &start_tx;
+	dev->stop = &netdev_close;
+	dev->get_stats = &get_stats;
+	dev->set_multicast_list = &set_rx_mode;
+	dev->do_ioctl = &netdev_ioctl;
+	SET_ETHTOOL_OPS(dev, &ethtool_ops);
+	dev->tx_timeout = &tx_timeout;
+	dev->watchdog_timeo = TX_TIMEOUT;
+	dev->change_mtu = &change_mtu;
+	pci_set_drvdata(pdev, dev);
+
+	pci_read_config_byte(pdev, PCI_REVISION_ID, &np->pci_rev_id);
+
+	i = register_netdev(dev);
+	if (i)
+		goto err_out_unmap_rx;
+
+	printk(KERN_INFO "%s: %s at %p, ",
+		   dev->name, pci_id_tbl[chip_idx].name, ioaddr);
+	for (i = 0; i < 5; i++)
+			printk("%2.2x:", dev->dev_addr[i]);
+	printk("%2.2x, IRQ %d.\n", dev->dev_addr[i], irq);
+
+	if (1) {
+		int phy, phy_idx = 0;
+		np->phys[0] = 1;		/* Default setting */
+		np->mii_preamble_required++;
+		for (phy = 1; phy < 32 && phy_idx < MII_CNT; phy++) {
+			int mii_status = mdio_read(dev, phy, MII_BMSR);
+			if (mii_status != 0xffff  &&  mii_status != 0x0000) {
+				np->phys[phy_idx++] = phy;
+				np->mii_if.advertising = mdio_read(dev, phy, MII_ADVERTISE);
+				if ((mii_status & 0x0040) == 0)
+					np->mii_preamble_required++;
+				printk(KERN_INFO "%s: MII PHY found at address %d, status "
+					   "0x%4.4x advertising %4.4x.\n",
+					   dev->name, phy, mii_status, np->mii_if.advertising);
+			}
+		}
+		np->mii_preamble_required--;
+
+		if (phy_idx == 0) {
+			printk(KERN_INFO "%s: No MII transceiver found, aborting.  ASIC status %x\n",
+				   dev->name, ioread32(ioaddr + ASICCtrl));
+			goto err_out_unregister;
+		}
+
+		np->mii_if.phy_id = np->phys[0];
+	}
+
+	/* Parse override configuration */
+	np->an_enable = 1;
+	if (card_idx < MAX_UNITS) {
+		if (media[card_idx] != NULL) {
+			np->an_enable = 0;
+			if (strcmp (media[card_idx], "100mbps_fd") == 0 ||
+			    strcmp (media[card_idx], "4") == 0) {
+				np->speed = 100;
+				np->mii_if.full_duplex = 1;
+			} else if (strcmp (media[card_idx], "100mbps_hd") == 0
+				   || strcmp (media[card_idx], "3") == 0) {
+				np->speed = 100;
+				np->mii_if.full_duplex = 0;
+			} else if (strcmp (media[card_idx], "10mbps_fd") == 0 ||
+				   strcmp (media[card_idx], "2") == 0) {
+				np->speed = 10;
+				np->mii_if.full_duplex = 1;
+			} else if (strcmp (media[card_idx], "10mbps_hd") == 0 ||
+				   strcmp (media[card_idx], "1") == 0) {
+				np->speed = 10;
+				np->mii_if.full_duplex = 0;
+			} else {
+				np->an_enable = 1;
+			}
+		}
+		if (flowctrl == 1)
+			np->flowctrl = 1;
+	}
+
+	/* Fibre PHY? */
+	if (ioread32 (ioaddr + ASICCtrl) & 0x80) {
+		/* Default 100Mbps Full */
+		if (np->an_enable) {
+			np->speed = 100;
+			np->mii_if.full_duplex = 1;
+			np->an_enable = 0;
+		}
+	}
+	/* Reset PHY */
+	mdio_write (dev, np->phys[0], MII_BMCR, BMCR_RESET);
+	mdelay (300);
+	/* If flow control enabled, we need to advertise it.*/
+	if (np->flowctrl)
+		mdio_write (dev, np->phys[0], MII_ADVERTISE, np->mii_if.advertising | 0x0400);
+	mdio_write (dev, np->phys[0], MII_BMCR, BMCR_ANENABLE|BMCR_ANRESTART);
+	/* Force media type */
+	if (!np->an_enable) {
+		mii_ctl = 0;
+		mii_ctl |= (np->speed == 100) ? BMCR_SPEED100 : 0;
+		mii_ctl |= (np->mii_if.full_duplex) ? BMCR_FULLDPLX : 0;
+		mdio_write (dev, np->phys[0], MII_BMCR, mii_ctl);
+		printk (KERN_INFO "Override speed=%d, %s duplex\n",
+			np->speed, np->mii_if.full_duplex ? "Full" : "Half");
+
+	}
+
+	/* Perhaps move the reset here? */
+	/* Reset the chip to erase previous misconfiguration. */
+	if (netif_msg_hw(np))
+		printk("ASIC Control is %x.\n", ioread32(ioaddr + ASICCtrl));
+	iowrite16(0x007f, ioaddr + ASICCtrl + 2);
+	if (netif_msg_hw(np))
+		printk("ASIC Control is now %x.\n", ioread32(ioaddr + ASICCtrl));
+
+	card_idx++;
+	return 0;
+
+err_out_unregister:
+	unregister_netdev(dev);
+err_out_unmap_rx:
+        pci_free_consistent(pdev, RX_TOTAL_SIZE, np->rx_ring, np->rx_ring_dma);
+err_out_unmap_tx:
+        pci_free_consistent(pdev, TX_TOTAL_SIZE, np->tx_ring, np->tx_ring_dma);
+err_out_cleardev:
+	pci_set_drvdata(pdev, NULL);
+	pci_iounmap(pdev, ioaddr);
+err_out_res:
+	pci_release_regions(pdev);
+err_out_netdev:
+	free_netdev (dev);
+	return -ENODEV;
+}
+
+static int change_mtu(struct net_device *dev, int new_mtu)
+{
+	if ((new_mtu < 68) || (new_mtu > 8191)) /* Set by RxDMAFrameLen */
+		return -EINVAL;
+	if (netif_running(dev))
+		return -EBUSY;
+	dev->mtu = new_mtu;
+	return 0;
+}
+
+#define eeprom_delay(ee_addr)	ioread32(ee_addr)
+/* Read the EEPROM and MII Management Data I/O (MDIO) interfaces. */
+static int __devinit eeprom_read(void __iomem *ioaddr, int location)
+{
+	int boguscnt = 10000;		/* Typical 1900 ticks. */
+	iowrite16(0x0200 | (location & 0xff), ioaddr + EECtrl);
+	do {
+		eeprom_delay(ioaddr + EECtrl);
+		if (! (ioread16(ioaddr + EECtrl) & 0x8000)) {
+			return ioread16(ioaddr + EEData);
+		}
+	} while (--boguscnt > 0);
+	return 0;
+}
+
+/*  MII transceiver control section.
+	Read and write the MII registers using software-generated serial
+	MDIO protocol.  See the MII specifications or DP83840A data sheet
+	for details.
+
+	The maximum data clock rate is 2.5 Mhz.  The minimum timing is usually
+	met by back-to-back 33Mhz PCI cycles. */
+#define mdio_delay() ioread8(mdio_addr)
+
+enum mii_reg_bits {
+	MDIO_ShiftClk=0x0001, MDIO_Data=0x0002, MDIO_EnbOutput=0x0004,
+};
+#define MDIO_EnbIn  (0)
+#define MDIO_WRITE0 (MDIO_EnbOutput)
+#define MDIO_WRITE1 (MDIO_Data | MDIO_EnbOutput)
+
+/* Generate the preamble required for initial synchronization and
+   a few older transceivers. */
+static void mdio_sync(void __iomem *mdio_addr)
+{
+	int bits = 32;
+
+	/* Establish sync by sending at least 32 logic ones. */
+	while (--bits >= 0) {
+		iowrite8(MDIO_WRITE1, mdio_addr);
+		mdio_delay();
+		iowrite8(MDIO_WRITE1 | MDIO_ShiftClk, mdio_addr);
+		mdio_delay();
+	}
+}
+
+static int mdio_read(struct net_device *dev, int phy_id, int location)
+{
+	struct netdev_private *np = netdev_priv(dev);
+	void __iomem *mdio_addr = np->base + MIICtrl;
+	int mii_cmd = (0xf6 << 10) | (phy_id << 5) | location;
+	int i, retval = 0;
+
+	if (np->mii_preamble_required)
+		mdio_sync(mdio_addr);
+
+	/* Shift the read command bits out. */
+	for (i = 15; i >= 0; i--) {
+		int dataval = (mii_cmd & (1 << i)) ? MDIO_WRITE1 : MDIO_WRITE0;
+
+		iowrite8(dataval, mdio_addr);
+		mdio_delay();
+		iowrite8(dataval | MDIO_ShiftClk, mdio_addr);
+		mdio_delay();
+	}
+	/* Read the two transition, 16 data, and wire-idle bits. */
+	for (i = 19; i > 0; i--) {
+		iowrite8(MDIO_EnbIn, mdio_addr);
+		mdio_delay();
+		retval = (retval << 1) | ((ioread8(mdio_addr) & MDIO_Data) ? 1 : 0);
+		iowrite8(MDIO_EnbIn | MDIO_ShiftClk, mdio_addr);
+		mdio_delay();
+	}
+	return (retval>>1) & 0xffff;
+}
+
+static void mdio_write(struct net_device *dev, int phy_id, int location, int value)
+{
+	struct netdev_private *np = netdev_priv(dev);
+	void __iomem *mdio_addr = np->base + MIICtrl;
+	int mii_cmd = (0x5002 << 16) | (phy_id << 23) | (location<<18) | value;
+	int i;
+
+	if (np->mii_preamble_required)
+		mdio_sync(mdio_addr);
+
+	/* Shift the command bits out. */
+	for (i = 31; i >= 0; i--) {
+		int dataval = (mii_cmd & (1 << i)) ? MDIO_WRITE1 : MDIO_WRITE0;
+
+		iowrite8(dataval, mdio_addr);
+		mdio_delay();
+		iowrite8(dataval | MDIO_ShiftClk, mdio_addr);
+		mdio_delay();
+	}
+	/* Clear out extra bits. */
+	for (i = 2; i > 0; i--) {
+		iowrite8(MDIO_EnbIn, mdio_addr);
+		mdio_delay();
+		iowrite8(MDIO_EnbIn | MDIO_ShiftClk, mdio_addr);
+		mdio_delay();
+	}
+	return;
+}
+
+static int netdev_open(struct net_device *dev)
+{
+	struct netdev_private *np = netdev_priv(dev);
+	void __iomem *ioaddr = np->base;
+	int i;
+
+	/* Do we need to reset the chip??? */
+
+	i = request_irq(dev->irq, &intr_handler, SA_SHIRQ, dev->name, dev);
+	if (i)
+		return i;
+
+	if (netif_msg_ifup(np))
+		printk(KERN_DEBUG "%s: netdev_open() irq %d.\n",
+			   dev->name, dev->irq);
+	init_ring(dev);
+
+	iowrite32(np->rx_ring_dma, ioaddr + RxListPtr);
+	/* The Tx list pointer is written as packets are queued. */
+
+	/* Initialize other registers. */
+	__set_mac_addr(dev);
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+	iowrite16(dev->mtu + 18, ioaddr + MaxFrameSize);
+#else
+	iowrite16(dev->mtu + 14, ioaddr + MaxFrameSize);
+#endif
+	if (dev->mtu > 2047)
+		iowrite32(ioread32(ioaddr + ASICCtrl) | 0x0C, ioaddr + ASICCtrl);
+
+	/* Configure the PCI bus bursts and FIFO thresholds. */
+
+	if (dev->if_port == 0)
+		dev->if_port = np->default_port;
+
+	spin_lock_init(&np->mcastlock);
+
+	set_rx_mode(dev);
+	iowrite16(0, ioaddr + IntrEnable);
+	iowrite16(0, ioaddr + DownCounter);
+	/* Set the chip to poll every N*320nsec. */
+	iowrite8(100, ioaddr + RxDMAPollPeriod);
+	iowrite8(127, ioaddr + TxDMAPollPeriod);
+	/* Fix DFE-580TX packet drop issue */
+	if (np->pci_rev_id >= 0x14)
+		iowrite8(0x01, ioaddr + DebugCtrl1);
+	netif_start_queue(dev);
+
+	iowrite16 (StatsEnable | RxEnable | TxEnable, ioaddr + MACCtrl1);
+
+	if (netif_msg_ifup(np))
+		printk(KERN_DEBUG "%s: Done netdev_open(), status: Rx %x Tx %x "
+			   "MAC Control %x, %4.4x %4.4x.\n",
+			   dev->name, ioread32(ioaddr + RxStatus), ioread8(ioaddr + TxStatus),
+			   ioread32(ioaddr + MACCtrl0),
+			   ioread16(ioaddr + MACCtrl1), ioread16(ioaddr + MACCtrl0));
+
+	/* Set the timer to check for link beat. */
+	init_timer(&np->timer);
+	np->timer.expires = jiffies + 3*HZ;
+	np->timer.data = (unsigned long)dev;
+	np->timer.function = &netdev_timer;				/* timer handler */
+	add_timer(&np->timer);
+
+	/* Enable interrupts by setting the interrupt mask. */
+	iowrite16(DEFAULT_INTR, ioaddr + IntrEnable);
+
+	return 0;
+}
+
+static void check_duplex(struct net_device *dev)
+{
+	struct netdev_private *np = netdev_priv(dev);
+	void __iomem *ioaddr = np->base;
+	int mii_lpa = mdio_read(dev, np->phys[0], MII_LPA);
+	int negotiated = mii_lpa & np->mii_if.advertising;
+	int duplex;
+
+	/* Force media */
+	if (!np->an_enable || mii_lpa == 0xffff) {
+		if (np->mii_if.full_duplex)
+			iowrite16 (ioread16 (ioaddr + MACCtrl0) | EnbFullDuplex,
+				ioaddr + MACCtrl0);
+		return;
+	}
+
+	/* Autonegotiation */
+	duplex = (negotiated & 0x0100) || (negotiated & 0x01C0) == 0x0040;
+	if (np->mii_if.full_duplex != duplex) {
+		np->mii_if.full_duplex = duplex;
+		if (netif_msg_link(np))
+			printk(KERN_INFO "%s: Setting %s-duplex based on MII #%d "
+				   "negotiated capability %4.4x.\n", dev->name,
+				   duplex ? "full" : "half", np->phys[0], negotiated);
+		iowrite16(ioread16(ioaddr + MACCtrl0) | duplex ? 0x20 : 0, ioaddr + MACCtrl0);
+	}
+}
+
+static void netdev_timer(unsigned long data)
+{
+	struct net_device *dev = (struct net_device *)data;
+	struct netdev_private *np = netdev_priv(dev);
+	void __iomem *ioaddr = np->base;
+	int next_tick = 10*HZ;
+
+	if (netif_msg_timer(np)) {
+		printk(KERN_DEBUG "%s: Media selection timer tick, intr status %4.4x, "
+			   "Tx %x Rx %x.\n",
+			   dev->name, ioread16(ioaddr + IntrEnable),
+			   ioread8(ioaddr + TxStatus), ioread32(ioaddr + RxStatus));
+	}
+	check_duplex(dev);
+	np->timer.expires = jiffies + next_tick;
+	add_timer(&np->timer);
+}
+
+static void tx_timeout(struct net_device *dev)
+{
+	struct netdev_private *np = netdev_priv(dev);
+	void __iomem *ioaddr = np->base;
+	unsigned long flag;
+	
+	netif_stop_queue(dev);
+	tasklet_disable(&np->tx_tasklet);
+	iowrite16(0, ioaddr + IntrEnable);
+	printk(KERN_WARNING "%s: Transmit timed out, TxStatus %2.2x "
+		   "TxFrameId %2.2x,"
+		   " resetting...\n", dev->name, ioread8(ioaddr + TxStatus),
+		   ioread8(ioaddr + TxFrameId));
+
+	{
+		int i;
+		for (i=0; i<TX_RING_SIZE; i++) {
+			printk(KERN_DEBUG "%02x %08llx %08x %08x(%02x) %08x %08x\n", i,
+				(unsigned long long)(np->tx_ring_dma + i*sizeof(*np->tx_ring)),
+				le32_to_cpu(np->tx_ring[i].next_desc),
+				le32_to_cpu(np->tx_ring[i].status),
+				(le32_to_cpu(np->tx_ring[i].status) >> 2) & 0xff,
+				le32_to_cpu(np->tx_ring[i].frag[0].addr), 
+				le32_to_cpu(np->tx_ring[i].frag[0].length));
+		}
+		printk(KERN_DEBUG "TxListPtr=%08x netif_queue_stopped=%d\n", 
+			ioread32(np->base + TxListPtr), 
+			netif_queue_stopped(dev));
+		printk(KERN_DEBUG "cur_tx=%d(%02x) dirty_tx=%d(%02x)\n", 
+			np->cur_tx, np->cur_tx % TX_RING_SIZE,
+			np->dirty_tx, np->dirty_tx % TX_RING_SIZE);
+		printk(KERN_DEBUG "cur_rx=%d dirty_rx=%d\n", np->cur_rx, np->dirty_rx);
+		printk(KERN_DEBUG "cur_task=%d\n", np->cur_task);
+	}
+	spin_lock_irqsave(&np->lock, flag);
+
+	/* Stop and restart the chip's Tx processes . */
+	reset_tx(dev);
+	spin_unlock_irqrestore(&np->lock, flag);
+
+	dev->if_port = 0;
+
+	dev->trans_start = jiffies;
+	np->stats.tx_errors++;
+	if (np->cur_tx - np->dirty_tx < TX_QUEUE_LEN - 4) {
+		netif_wake_queue(dev);
+	}
+	iowrite16(DEFAULT_INTR, ioaddr + IntrEnable);
+	tasklet_enable(&np->tx_tasklet);
+}
+
+
+/* Initialize the Rx and Tx rings, along with various 'dev' bits. */
+static void init_ring(struct net_device *dev)
+{
+	struct netdev_private *np = netdev_priv(dev);
+	int i;
+
+	np->cur_rx = np->cur_tx = 0;
+	np->dirty_rx = np->dirty_tx = 0;
+	np->cur_task = 0;
+
+	np->rx_buf_sz = (dev->mtu <= 1520 ? PKT_BUF_SZ : dev->mtu + 16);
+
+	/* Initialize all Rx descriptors. */
+	for (i = 0; i < RX_RING_SIZE; i++) {
+		np->rx_ring[i].next_desc = cpu_to_le32(np->rx_ring_dma +
+			((i+1)%RX_RING_SIZE)*sizeof(*np->rx_ring));
+		np->rx_ring[i].status = 0;
+		np->rx_ring[i].frag[0].length = 0;
+		np->rx_skbuff[i] = NULL;
+	}
+
+	/* Fill in the Rx buffers.  Handle allocation failure gracefully. */
+	for (i = 0; i < RX_RING_SIZE; i++) {
+		struct sk_buff *skb = dev_alloc_skb(np->rx_buf_sz);
+		np->rx_skbuff[i] = skb;
+		if (skb == NULL)
+			break;
+		skb->dev = dev;		/* Mark as being used by this device. */
+		skb_reserve(skb, 2);	/* 16 byte align the IP header. */
+		np->rx_ring[i].frag[0].addr = cpu_to_le32(
+			pci_map_single(np->pci_dev, skb->tail, np->rx_buf_sz,
+				PCI_DMA_FROMDEVICE));
+		np->rx_ring[i].frag[0].length = cpu_to_le32(np->rx_buf_sz | LastFrag);
+	}
+	np->dirty_rx = (unsigned int)(i - RX_RING_SIZE);
+
+	for (i = 0; i < TX_RING_SIZE; i++) {
+		np->tx_skbuff[i] = NULL;
+		np->tx_ring[i].status = 0;
+	}
+	return;
+}
+
+static void tx_poll (unsigned long data)
+{
+	struct net_device *dev = (struct net_device *)data;
+	struct netdev_private *np = netdev_priv(dev);
+	unsigned head = np->cur_task % TX_RING_SIZE;
+	struct netdev_desc *txdesc = 
+		&np->tx_ring[(np->cur_tx - 1) % TX_RING_SIZE];
+	
+	/* Chain the next pointer */
+	for (; np->cur_tx - np->cur_task > 0; np->cur_task++) {
+		int entry = np->cur_task % TX_RING_SIZE;
+		txdesc = &np->tx_ring[entry];
+		if (np->last_tx) {
+			np->last_tx->next_desc = cpu_to_le32(np->tx_ring_dma +
+				entry*sizeof(struct netdev_desc));
+		}
+		np->last_tx = txdesc;
+	}
+	/* Indicate the latest desc