[netdrvr] new driver skge, for SysKonnect cards

1 files changed, 3005 insertions, 0 deletions

diff --git a/drivers/net/skge.h b/drivers/net/skge.h
new file mode 100644
index 00000000000..36c62b68fab
--- /dev/null
+++ b/drivers/net/skge.h
@@ -0,0 +1,3005 @@
+/*
+ * Definitions for the new Marvell Yukon / SysKonenct driver.
+ */
+#ifndef _SKGE_H
+#define _SKGE_H
+
+/* PCI config registers */
+#define PCI_DEV_REG1	0x40
+#define PCI_DEV_REG2	0x44
+#ifndef PCI_VPD
+#define PCI_VPD		0x50
+#endif
+
+/*	PCI_OUR_REG_2		32 bit	Our Register 2 */
+enum {
+	PCI_VPD_WR_THR  = 0xff<<24, /* Bit 31..24:	VPD Write Threshold */
+	PCI_DEV_SEL	= 0x7f<<17, /* Bit 23..17:	EEPROM Device Select */
+	PCI_VPD_ROM_SZ  = 7   <<14, /* Bit 16..14:	VPD ROM Size	*/
+ 				    /* Bit 13..12:	reserved	*/
+	PCI_EN_DUMMY_RD = 1<<3, /* Enable Dummy Read */
+	PCI_REV_DESC    = 1<<2, /* Reverse Desc. Bytes */
+	PCI_USEDATA64   = 1<<0, /* Use 64Bit Data bus ext */
+};
+
+/*	PCI_VPD_ADR_REG		16 bit	VPD Address Register */
+enum {
+	PCI_VPD_FLAG	= 1<<15,  /* starts VPD rd/wr cycle */
+	PCI_VPD_ADR_MSK =0x7fffL, /* Bit 14.. 0:	VPD Address Mask */
+	VPD_RES_ID	= 0x82,
+	VPD_RES_READ	= 0x90,
+	VPD_RES_WRITE	= 0x81,
+	VPD_RES_END	= 0x78,
+};
+
+
+#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
+			       PCI_STATUS_SIG_SYSTEM_ERROR | \
+			       PCI_STATUS_REC_MASTER_ABORT | \
+			       PCI_STATUS_REC_TARGET_ABORT | \
+			       PCI_STATUS_PARITY)
+
+
+enum csr_regs {
+	B0_RAP	= 0x0000,
+	B0_CTST	= 0x0004,
+	B0_LED	= 0x0006,
+	B0_POWER_CTRL	= 0x0007,
+	B0_ISRC	= 0x0008,
+	B0_IMSK	= 0x000c,
+	B0_HWE_ISRC	= 0x0010,
+	B0_HWE_IMSK	= 0x0014,
+	B0_SP_ISRC	= 0x0018,
+	B0_XM1_IMSK	= 0x0020,
+	B0_XM1_ISRC	= 0x0028,
+	B0_XM1_PHY_ADDR	= 0x0030,
+	B0_XM1_PHY_DATA	= 0x0034,
+	B0_XM2_IMSK	= 0x0040,
+	B0_XM2_ISRC	= 0x0048,
+	B0_XM2_PHY_ADDR	= 0x0050,
+	B0_XM2_PHY_DATA	= 0x0054,
+	B0_R1_CSR	= 0x0060,
+	B0_R2_CSR	= 0x0064,
+	B0_XS1_CSR	= 0x0068,
+	B0_XA1_CSR	= 0x006c,
+	B0_XS2_CSR	= 0x0070,
+	B0_XA2_CSR	= 0x0074,
+
+	B2_MAC_1	= 0x0100,
+	B2_MAC_2	= 0x0108,
+	B2_MAC_3	= 0x0110,
+	B2_CONN_TYP	= 0x0118,
+	B2_PMD_TYP	= 0x0119,
+	B2_MAC_CFG	= 0x011a,
+	B2_CHIP_ID	= 0x011b,
+	B2_E_0		= 0x011c,
+	B2_E_1		= 0x011d,
+	B2_E_2		= 0x011e,
+	B2_E_3		= 0x011f,
+	B2_FAR		= 0x0120,
+	B2_FDP		= 0x0124,
+	B2_LD_CTRL	= 0x0128,
+	B2_LD_TEST	= 0x0129,
+	B2_TI_INI	= 0x0130,
+	B2_TI_VAL	= 0x0134,
+	B2_TI_CTRL	= 0x0138,
+	B2_TI_TEST	= 0x0139,
+	B2_IRQM_INI	= 0x0140,
+	B2_IRQM_VAL	= 0x0144,
+	B2_IRQM_CTRL	= 0x0148,
+	B2_IRQM_TEST	= 0x0149,
+	B2_IRQM_MSK	= 0x014c,
+	B2_IRQM_HWE_MSK	= 0x0150,
+	B2_TST_CTRL1	= 0x0158,
+	B2_TST_CTRL2	= 0x0159,
+	B2_GP_IO	= 0x015c,
+	B2_I2C_CTRL	= 0x0160,
+	B2_I2C_DATA	= 0x0164,
+	B2_I2C_IRQ	= 0x0168,
+	B2_I2C_SW	= 0x016c,
+	B2_BSC_INI	= 0x0170,
+	B2_BSC_VAL	= 0x0174,
+	B2_BSC_CTRL	= 0x0178,
+	B2_BSC_STAT	= 0x0179,
+	B2_BSC_TST	= 0x017a,
+
+	B3_RAM_ADDR	= 0x0180,
+	B3_RAM_DATA_LO	= 0x0184,
+	B3_RAM_DATA_HI	= 0x0188,
+	B3_RI_WTO_R1	= 0x0190,
+	B3_RI_WTO_XA1	= 0x0191,
+	B3_RI_WTO_XS1	= 0x0192,
+	B3_RI_RTO_R1	= 0x0193,
+	B3_RI_RTO_XA1	= 0x0194,
+	B3_RI_RTO_XS1	= 0x0195,
+	B3_RI_WTO_R2	= 0x0196,
+	B3_RI_WTO_XA2	= 0x0197,
+	B3_RI_WTO_XS2	= 0x0198,
+	B3_RI_RTO_R2	= 0x0199,
+	B3_RI_RTO_XA2	= 0x019a,
+	B3_RI_RTO_XS2	= 0x019b,
+	B3_RI_TO_VAL	= 0x019c,
+	B3_RI_CTRL	= 0x01a0,
+	B3_RI_TEST	= 0x01a2,
+	B3_MA_TOINI_RX1	= 0x01b0,
+	B3_MA_TOINI_RX2	= 0x01b1,
+	B3_MA_TOINI_TX1	= 0x01b2,
+	B3_MA_TOINI_TX2	= 0x01b3,
+	B3_MA_TOVAL_RX1	= 0x01b4,
+	B3_MA_TOVAL_RX2	= 0x01b5,
+	B3_MA_TOVAL_TX1	= 0x01b6,
+	B3_MA_TOVAL_TX2	= 0x01b7,
+	B3_MA_TO_CTRL	= 0x01b8,
+	B3_MA_TO_TEST	= 0x01ba,
+	B3_MA_RCINI_RX1	= 0x01c0,
+	B3_MA_RCINI_RX2	= 0x01c1,
+	B3_MA_RCINI_TX1	= 0x01c2,
+	B3_MA_RCINI_TX2	= 0x01c3,
+	B3_MA_RCVAL_RX1	= 0x01c4,
+	B3_MA_RCVAL_RX2	= 0x01c5,
+	B3_MA_RCVAL_TX1	= 0x01c6,
+	B3_MA_RCVAL_TX2	= 0x01c7,
+	B3_MA_RC_CTRL	= 0x01c8,
+	B3_MA_RC_TEST	= 0x01ca,
+	B3_PA_TOINI_RX1	= 0x01d0,
+	B3_PA_TOINI_RX2	= 0x01d4,
+	B3_PA_TOINI_TX1	= 0x01d8,
+	B3_PA_TOINI_TX2	= 0x01dc,
+	B3_PA_TOVAL_RX1	= 0x01e0,
+	B3_PA_TOVAL_RX2	= 0x01e4,
+	B3_PA_TOVAL_TX1	= 0x01e8,
+	B3_PA_TOVAL_TX2	= 0x01ec,
+	B3_PA_CTRL	= 0x01f0,
+	B3_PA_TEST	= 0x01f2,
+};
+
+/*	B0_CTST			16 bit	Control/Status register */
+enum {
+	CS_CLK_RUN_HOT	= 1<<13,/* CLK_RUN hot m. (YUKON-Lite only) */
+	CS_CLK_RUN_RST	= 1<<12,/* CLK_RUN reset  (YUKON-Lite only) */
+	CS_CLK_RUN_ENA	= 1<<11,/* CLK_RUN enable (YUKON-Lite only) */
+	CS_VAUX_AVAIL	= 1<<10,/* VAUX available (YUKON only) */
+	CS_BUS_CLOCK	= 1<<9,	/* Bus Clock 0/1 = 33/66 MHz */
+	CS_BUS_SLOT_SZ	= 1<<8,	/* Slot Size 0/1 = 32/64 bit slot */
+	CS_ST_SW_IRQ	= 1<<7,	/* Set IRQ SW Request */
+	CS_CL_SW_IRQ	= 1<<6,	/* Clear IRQ SW Request */
+	CS_STOP_DONE	= 1<<5,	/* Stop Master is finished */
+	CS_STOP_MAST	= 1<<4,	/* Command Bit to stop the master */
+	CS_MRST_CLR	= 1<<3,	/* Clear Master reset	*/
+	CS_MRST_SET	= 1<<2,	/* Set Master reset	*/
+	CS_RST_CLR	= 1<<1,	/* Clear Software reset	*/
+	CS_RST_SET	= 1,	/* Set   Software reset	*/
+
+/*	B0_LED			 8 Bit	LED register */
+/* Bit  7.. 2:	reserved */
+	LED_STAT_ON	= 1<<1,	/* Status LED on	*/
+	LED_STAT_OFF	= 1,		/* Status LED off	*/
+
+/*	B0_POWER_CTRL	 8 Bit	Power Control reg (YUKON only) */
+	PC_VAUX_ENA	= 1<<7,	/* Switch VAUX Enable  */
+	PC_VAUX_DIS	= 1<<6,	/* Switch VAUX Disable */
+	PC_VCC_ENA	= 1<<5,	/* Switch VCC Enable  */
+	PC_VCC_DIS	= 1<<4,	/* Switch VCC Disable */
+	PC_VAUX_ON	= 1<<3,	/* Switch VAUX On  */
+	PC_VAUX_OFF	= 1<<2,	/* Switch VAUX Off */
+	PC_VCC_ON	= 1<<1,	/* Switch VCC On  */
+	PC_VCC_OFF	= 1<<0,	/* Switch VCC Off */
+};
+
+/*	B2_IRQM_MSK 	32 bit	IRQ Moderation Mask */
+enum {
+	IS_ALL_MSK	= 0xbffffffful,	/* All Interrupt bits */
+	IS_HW_ERR	= 1<<31,	/* Interrupt HW Error */
+					/* Bit 30:	reserved */
+	IS_PA_TO_RX1	= 1<<29,	/* Packet Arb Timeout Rx1 */
+	IS_PA_TO_RX2	= 1<<28,	/* Packet Arb Timeout Rx2 */
+	IS_PA_TO_TX1	= 1<<27,	/* Packet Arb Timeout Tx1 */
+	IS_PA_TO_TX2	= 1<<26,	/* Packet Arb Timeout Tx2 */
+	IS_I2C_READY	= 1<<25,	/* IRQ on end of I2C Tx */
+	IS_IRQ_SW	= 1<<24,	/* SW forced IRQ	*/
+	IS_EXT_REG	= 1<<23,	/* IRQ from LM80 or PHY (GENESIS only) */
+					/* IRQ from PHY (YUKON only) */
+	IS_TIMINT	= 1<<22,	/* IRQ from Timer	*/
+	IS_MAC1		= 1<<21,	/* IRQ from MAC 1	*/
+	IS_LNK_SYNC_M1	= 1<<20,	/* Link Sync Cnt wrap MAC 1 */
+	IS_MAC2		= 1<<19,	/* IRQ from MAC 2	*/
+	IS_LNK_SYNC_M2	= 1<<18,	/* Link Sync Cnt wrap MAC 2 */
+/* Receive Queue 1 */
+	IS_R1_B		= 1<<17,	/* Q_R1 End of Buffer */
+	IS_R1_F		= 1<<16,	/* Q_R1 End of Frame */
+	IS_R1_C		= 1<<15,	/* Q_R1 Encoding Error */
+/* Receive Queue 2 */
+	IS_R2_B		= 1<<14,	/* Q_R2 End of Buffer */
+	IS_R2_F		= 1<<13,	/* Q_R2 End of Frame */
+	IS_R2_C		= 1<<12,	/* Q_R2 Encoding Error */
+/* Synchronous Transmit Queue 1 */
+	IS_XS1_B	= 1<<11,	/* Q_XS1 End of Buffer */
+	IS_XS1_F	= 1<<10,	/* Q_XS1 End of Frame */
+	IS_XS1_C	= 1<<9,		/* Q_XS1 Encoding Error */
+/* Asynchronous Transmit Queue 1 */
+	IS_XA1_B	= 1<<8,		/* Q_XA1 End of Buffer */
+	IS_XA1_F	= 1<<7,		/* Q_XA1 End of Frame */
+	IS_XA1_C	= 1<<6,		/* Q_XA1 Encoding Error */
+/* Synchronous Transmit Queue 2 */
+	IS_XS2_B	= 1<<5,		/* Q_XS2 End of Buffer */
+	IS_XS2_F	= 1<<4,		/* Q_XS2 End of Frame */
+	IS_XS2_C	= 1<<3,		/* Q_XS2 Encoding Error */
+/* Asynchronous Transmit Queue 2 */
+	IS_XA2_B	= 1<<2,		/* Q_XA2 End of Buffer */
+	IS_XA2_F	= 1<<1,		/* Q_XA2 End of Frame */
+	IS_XA2_C	= 1<<0,		/* Q_XA2 Encoding Error */
+
+	IS_PORT_1	= IS_XA1_F| IS_R1_F| IS_MAC1,
+	IS_PORT_2	= IS_XA2_F| IS_R2_F| IS_MAC2,
+};
+
+
+/*	B2_IRQM_HWE_MSK	32 bit	IRQ Moderation HW Error Mask */
+enum {
+	IS_ERR_MSK	= 0x00003fff,/* 		All Error bits */
+
+	IS_IRQ_TIST_OV	= 1<<13, /* Time Stamp Timer Overflow (YUKON only) */
+	IS_IRQ_SENSOR	= 1<<12, /* IRQ from Sensor (YUKON only) */
+	IS_IRQ_MST_ERR	= 1<<11, /* IRQ master error detected */
+	IS_IRQ_STAT	= 1<<10, /* IRQ status exception */
+	IS_NO_STAT_M1	= 1<<9,	/* No Rx Status from MAC 1 */
+	IS_NO_STAT_M2	= 1<<8,	/* No Rx Status from MAC 2 */
+	IS_NO_TIST_M1	= 1<<7,	/* No Time Stamp from MAC 1 */
+	IS_NO_TIST_M2	= 1<<6,	/* No Time Stamp from MAC 2 */
+	IS_RAM_RD_PAR	= 1<<5,	/* RAM Read  Parity Error */
+	IS_RAM_WR_PAR	= 1<<4,	/* RAM Write Parity Error */
+	IS_M1_PAR_ERR	= 1<<3,	/* MAC 1 Parity Error */
+	IS_M2_PAR_ERR	= 1<<2,	/* MAC 2 Parity Error */
+	IS_R1_PAR_ERR	= 1<<1,	/* Queue R1 Parity Error */
+	IS_R2_PAR_ERR	= 1<<0,	/* Queue R2 Parity Error */
+};
+
+/*	B2_TST_CTRL1	 8 bit	Test Control Register 1 */
+enum {
+	TST_FRC_DPERR_MR = 1<<7, /* force DATAPERR on MST RD */
+	TST_FRC_DPERR_MW = 1<<6, /* force DATAPERR on MST WR */
+	TST_FRC_DPERR_TR = 1<<5, /* force DATAPERR on TRG RD */
+	TST_FRC_DPERR_TW = 1<<4, /* force DATAPERR on TRG WR */
+	TST_FRC_APERR_M	 = 1<<3, /* force ADDRPERR on MST */
+	TST_FRC_APERR_T	 = 1<<2, /* force ADDRPERR on TRG */
+	TST_CFG_WRITE_ON = 1<<1, /* Enable  Config Reg WR */
+	TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */
+};
+
+/*	B2_MAC_CFG		 8 bit	MAC Configuration / Chip Revision */
+enum {
+	CFG_CHIP_R_MSK	  = 0xf<<4,	/* Bit 7.. 4: Chip Revision */
+					/* Bit 3.. 2:	reserved */
+	CFG_DIS_M2_CLK	  = 1<<1,	/* Disable Clock for 2nd MAC */
+	CFG_SNG_MAC	  = 1<<0,	/* MAC Config: 0=2 MACs / 1=1 MAC*/
+};
+
+/*	B2_CHIP_ID		 8 bit 	Chip Identification Number */
+enum {
+	CHIP_ID_GENESIS	   = 0x0a, /* Chip ID for GENESIS */
+	CHIP_ID_YUKON	   = 0xb0, /* Chip ID for YUKON */
+	CHIP_ID_YUKON_LITE = 0xb1, /* Chip ID for YUKON-Lite (Rev. A1-A3) */
+	CHIP_ID_YUKON_LP   = 0xb2, /* Chip ID for YUKON-LP */
+	CHIP_ID_YUKON_XL   = 0xb3, /* Chip ID for YUKON-2 XL */
+	CHIP_ID_YUKON_EC   = 0xb6, /* Chip ID for YUKON-2 EC */
+ 	CHIP_ID_YUKON_FE   = 0xb7, /* Chip ID for YUKON-2 FE */
+
+	CHIP_REV_YU_LITE_A1  = 3,	/* Chip Rev. for YUKON-Lite A1,A2 */
+	CHIP_REV_YU_LITE_A3  = 7,	/* Chip Rev. for YUKON-Lite A3 */
+};
+
+/*	B2_LD_TEST		 8 bit	EPROM loader test register */
+enum {
+	LD_T_ON		= 1<<3,	/* Loader Test mode on */
+	LD_T_OFF	= 1<<2,	/* Loader Test mode off */
+	LD_T_STEP	= 1<<1,	/* Decrement FPROM addr. Counter */
+	LD_START	= 1<<0,	/* Start loading FPROM */
+};
+
+/*	B2_TI_CTRL		 8 bit	Timer control */
+/*	B2_IRQM_CTRL	 8 bit	IRQ Moderation Timer Control */
+enum {
+	TIM_START	= 1<<2,	/* Start Timer */
+	TIM_STOP	= 1<<1,	/* Stop  Timer */
+	TIM_CLR_IRQ	= 1<<0,	/* Clear Timer IRQ (!IRQM) */
+};
+
+/*	B2_TI_TEST		 8 Bit	Timer Test */
+/*	B2_IRQM_TEST	 8 bit	IRQ Moderation Timer Test */
+/*	B28_DPT_TST		 8 bit	Descriptor Poll Timer Test Reg */
+enum {
+	TIM_T_ON	= 1<<2,	/* Test mode on */
+	TIM_T_OFF	= 1<<1,	/* Test mode off */
+	TIM_T_STEP	= 1<<0,	/* Test step */
+};
+
+/*	B28_DPT_INI	32 bit	Descriptor Poll Timer Init Val */
+/*	B28_DPT_VAL	32 bit	Descriptor Poll Timer Curr Val */
+/*	B28_DPT_CTRL	 8 bit	Descriptor Poll Timer Ctrl Reg */
+enum {
+	DPT_MSK	= 0x00ffffffL,	/* Bit 23.. 0:	Desc Poll Timer Bits */
+
+	DPT_START	= 1<<1,	/* Start Descriptor Poll Timer */
+	DPT_STOP	= 1<<0,	/* Stop  Descriptor Poll Timer */
+};
+
+/*	B2_GP_IO		32 bit	General Purpose I/O Register */
+enum {
+	GP_DIR_9 = 1<<25, /* IO_9 direct, 0=In/1=Out */
+	GP_DIR_8 = 1<<24, /* IO_8 direct, 0=In/1=Out */
+	GP_DIR_7 = 1<<23, /* IO_7 direct, 0=In/1=Out */
+	GP_DIR_6 = 1<<22, /* IO_6 direct, 0=In/1=Out */
+	GP_DIR_5 = 1<<21, /* IO_5 direct, 0=In/1=Out */
+	GP_DIR_4 = 1<<20, /* IO_4 direct, 0=In/1=Out */
+	GP_DIR_3 = 1<<19, /* IO_3 direct, 0=In/1=Out */
+	GP_DIR_2 = 1<<18, /* IO_2 direct, 0=In/1=Out */
+	GP_DIR_1 = 1<<17, /* IO_1 direct, 0=In/1=Out */
+	GP_DIR_0 = 1<<16, /* IO_0 direct, 0=In/1=Out */
+
+	GP_IO_9	= 1<<9,	/* IO_9 pin */
+	GP_IO_8	= 1<<8,	/* IO_8 pin */
+	GP_IO_7	= 1<<7,	/* IO_7 pin */
+	GP_IO_6	= 1<<6,	/* IO_6 pin */
+	GP_IO_5	= 1<<5,	/* IO_5 pin */
+	GP_IO_4	= 1<<4,	/* IO_4 pin */
+	GP_IO_3	= 1<<3,	/* IO_3 pin */
+	GP_IO_2	= 1<<2,	/* IO_2 pin */
+	GP_IO_1	= 1<<1,	/* IO_1 pin */
+	GP_IO_0	= 1<<0,	/* IO_0 pin */
+};
+
+/* Rx/Tx Path related Arbiter Test Registers */
+/*	B3_MA_TO_TEST	16 bit	MAC Arbiter Timeout Test Reg */
+/*	B3_MA_RC_TEST	16 bit	MAC Arbiter Recovery Test Reg */
+/*	B3_PA_TEST		16 bit	Packet Arbiter Test Register */
+/*			Bit 15, 11, 7, and 3 are reserved in B3_PA_TEST */
+enum {
+	TX2_T_EV	= 1<<15,/* TX2 Timeout/Recv Event occured */
+	TX2_T_ON	= 1<<14,/* TX2 Timeout/Recv Timer Test On */
+	TX2_T_OFF	= 1<<13,/* TX2 Timeout/Recv Timer Tst Off */
+	TX2_T_STEP	= 1<<12,/* TX2 Timeout/Recv Timer Step */
+	TX1_T_EV	= 1<<11,/* TX1 Timeout/Recv Event occured */
+	TX1_T_ON	= 1<<10,/* TX1 Timeout/Recv Timer Test On */
+	TX1_T_OFF	= 1<<9,	/* TX1 Timeout/Recv Timer Tst Off */
+	TX1_T_STEP	= 1<<8,	/* TX1 Timeout/Recv Timer Step */
+	RX2_T_EV	= 1<<7,	/* RX2 Timeout/Recv Event occured */
+	RX2_T_ON	= 1<<6,	/* RX2 Timeout/Recv Timer Test On */
+	RX2_T_OFF	= 1<<5,	/* RX2 Timeout/Recv Timer Tst Off */
+	RX2_T_STEP	= 1<<4,	/* RX2 Timeout/Recv Timer Step */
+	RX1_T_EV	= 1<<3,	/* RX1 Timeout/Recv Event occured */
+	RX1_T_ON	= 1<<2,	/* RX1 Timeout/Recv Timer Test On */
+	RX1_T_OFF	= 1<<1,	/* RX1 Timeout/Recv Timer Tst Off */
+	RX1_T_STEP	= 1<<0,	/* RX1 Timeout/Recv Timer Step */
+};
+
+/* Descriptor Bit Definition */
+/*	TxCtrl		Transmit Buffer Control Field */
+/*	RxCtrl		Receive  Buffer Control Field */
+enum {
+	BMU_OWN		= 1<<31, /* OWN bit: 0=host/1=BMU */
+	BMU_STF		= 1<<30, /* Start of Frame */
+	BMU_EOF		= 1<<29, /* End of Frame */
+	BMU_IRQ_EOB	= 1<<28, /* Req "End of Buffer" IRQ */
+	BMU_IRQ_EOF	= 1<<27, /* Req "End of Frame" IRQ */
+				/* TxCtrl specific bits */
+	BMU_STFWD	= 1<<26, /* (Tx)	Store & Forward Frame */
+	BMU_NO_FCS	= 1<<25, /* (Tx) Disable MAC FCS (CRC) generation */
+	BMU_SW	= 1<<24, /* (Tx)	1 bit res. for SW use */
+				/* RxCtrl specific bits */
+	BMU_DEV_0	= 1<<26, /* (Rx)	Transfer data to Dev0 */
+	BMU_STAT_VAL	= 1<<25, /* (Rx)	Rx Status Valid */
+	BMU_TIST_VAL	= 1<<24, /* (Rx)	Rx TimeStamp Valid */
+			/* Bit 23..16:	BMU Check Opcodes */
+	BMU_CHECK	= 0x55<<16, /* Default BMU check */
+	BMU_TCP_CHECK	= 0x56<<16, /* Descr with TCP ext */
+	BMU_UDP_CHECK	= 0x57<<16, /* Descr with UDP ext (YUKON only) */
+	BMU_BBC		= 0xffffL, /* Bit 15.. 0:	Buffer Byte Counter */
+};
+
+/*	B2_BSC_CTRL		 8 bit	Blink Source Counter Control */
+enum {
+	 BSC_START	= 1<<1,	/* Start Blink Source Counter */
+	 BSC_STOP	= 1<<0,	/* Stop  Blink Source Counter */
+};
+
+/*	B2_BSC_STAT		 8 bit	Blink Source Counter Status */
+enum {
+	BSC_SRC		= 1<<0,	/* Blink Source, 0=Off / 1=On */
+};
+
+/*	B2_BSC_TST		16 bit	Blink Source Counter Test Reg */
+enum {
+	BSC_T_ON	= 1<<2,	/* Test mode on */
+	BSC_T_OFF	= 1<<1,	/* Test mode off */
+	BSC_T_STEP	= 1<<0,	/* Test step */
+};
+
+/*	B3_RAM_ADDR		32 bit	RAM Address, to read or write */
+					/* Bit 31..19:	reserved */
+#define RAM_ADR_RAN	0x0007ffffL	/* Bit 18.. 0:	RAM Address Range */
+/* RAM Interface Registers */
+
+/*	B3_RI_CTRL		16 bit	RAM Iface Control Register */
+enum {
+	RI_CLR_RD_PERR	= 1<<9,	/* Clear IRQ RAM Read Parity Err */
+	RI_CLR_WR_PERR	= 1<<8,	/* Clear IRQ RAM Write Parity Err*/
+
+	RI_RST_CLR	= 1<<1,	/* Clear RAM Interface Reset */
+	RI_RST_SET	= 1<<0,	/* Set   RAM Interface Reset */
+};
+
+/*	B3_RI_TEST		 8 bit	RAM Iface Test Register */
+enum {
+	RI_T_EV	= 1<<3,	/* Timeout Event occured */
+	RI_T_ON	= 1<<2,	/* Timeout Timer Test On */
+	RI_T_OFF	= 1<<1,	/* Timeout Timer Test Off */
+	RI_T_STEP	= 1<<0,	/* Timeout Timer Step */
+};
+
+/* MAC Arbiter Registers */
+/*	B3_MA_TO_CTRL	16 bit	MAC Arbiter Timeout Ctrl Reg */
+enum {
+	MA_FOE_ON	= 1<<3,	/* XMAC Fast Output Enable ON */
+	MA_FOE_OFF	= 1<<2,	/* XMAC Fast Output Enable OFF */
+	MA_RST_CLR	= 1<<1,	/* Clear MAC Arbiter Reset */
+	MA_RST_SET	= 1<<0,	/* Set   MAC Arbiter Reset */
+
+};
+
+/* Timeout values */
+#define SK_MAC_TO_53	72		/* MAC arbiter timeout */
+#define SK_PKT_TO_53	0x2000		/* Packet arbiter timeout */
+#define SK_PKT_TO_MAX	0xffff		/* Maximum value */
+#define SK_RI_TO_53	36		/* RAM interface timeout */
+
+
+/*	B3_MA_RC_CTRL	16 bit	MAC Arbiter Recovery Ctrl Reg */
+enum {
+	MA_ENA_REC_TX2	= 1<<7,	/* Enable  Recovery Timer TX2 */
+	MA_DIS_REC_TX2	= 1<<6,	/* Disable Recovery Timer TX2 */
+	MA_ENA_REC_TX1	= 1<<5,	/* Enable  Recovery Timer TX1 */
+	MA_DIS_REC_TX1	= 1<<4,	/* Disable Recovery Timer TX1 */
+	MA_ENA_REC_RX2	= 1<<3,	/* Enable  Recovery Timer RX2 */
+	MA_DIS_REC_RX2	= 1<<2,	/* Disable Recovery Timer RX2 */
+	MA_ENA_REC_RX1	= 1<<1,	/* Enable  Recovery Timer RX1 */
+	MA_DIS_REC_RX1	= 1<<0,	/* Disable Recovery Timer RX1 */
+};
+
+/* Packet Arbiter Registers */
+/*	B3_PA_CTRL		16 bit	Packet Arbiter Ctrl Register */
+enum {
+	PA_CLR_TO_TX2	= 1<<13,	/* Clear IRQ Packet Timeout TX2 */
+	PA_CLR_TO_TX1	= 1<<12,	/* Clear IRQ Packet Timeout TX1 */
+	PA_CLR_TO_RX2	= 1<<11,	/* Clear IRQ Packet Timeout RX2 */
+	PA_CLR_TO_RX1	= 1<<10,	/* Clear IRQ Packet Timeout RX1 */
+	PA_ENA_TO_TX2	= 1<<9,	/* Enable  Timeout Timer TX2 */
+	PA_DIS_TO_TX2	= 1<<8,	/* Disable Timeout Timer TX2 */
+	PA_ENA_TO_TX1	= 1<<7,	/* Enable  Timeout Timer TX1 */
+	PA_DIS_TO_TX1	= 1<<6,	/* Disable Timeout Timer TX1 */
+	PA_ENA_TO_RX2	= 1<<5,	/* Enable  Timeout Timer RX2 */
+	PA_DIS_TO_RX2	= 1<<4,	/* Disable Timeout Timer RX2 */
+	PA_ENA_TO_RX1	= 1<<3,	/* Enable  Timeout Timer RX1 */
+	PA_DIS_TO_RX1	= 1<<2,	/* Disable Timeout Timer RX1 */
+	PA_RST_CLR	= 1<<1,	/* Clear MAC Arbiter Reset */
+	PA_RST_SET	= 1<<0,	/* Set   MAC Arbiter Reset */
+};
+
+#define PA_ENA_TO_ALL	(PA_ENA_TO_RX1 | PA_ENA_TO_RX2 |\
+						PA_ENA_TO_TX1 | PA_ENA_TO_TX2)
+
+
+/* Transmit Arbiter Registers MAC 1 and 2, use MR_ADDR() to access */
+/*	TXA_ITI_INI		32 bit	Tx Arb Interval Timer Init Val */
+/*	TXA_ITI_VAL		32 bit	Tx Arb Interval Timer Value */
+/*	TXA_LIM_INI		32 bit	Tx Arb Limit Counter Init Val */
+/*	TXA_LIM_VAL		32 bit	Tx Arb Limit Counter Value */
+
+#define TXA_MAX_VAL	0x00ffffffUL	/* Bit 23.. 0:	Max TXA Timer/Cnt Val */
+
+/*	TXA_CTRL		 8 bit	Tx Arbiter Control Register */
+enum {
+	TXA_ENA_FSYNC	= 1<<7,	/* Enable  force of sync Tx queue */
+	TXA_DIS_FSYNC	= 1<<6,	/* Disable force of sync Tx queue */
+	TXA_ENA_ALLOC	= 1<<5,	/* Enable  alloc of free bandwidth */
+	TXA_DIS_ALLOC	= 1<<4,	/* Disable alloc of free bandwidth */
+	TXA_START_RC	= 1<<3,	/* Start sync Rate Control */
+	TXA_STOP_RC	= 1<<2,	/* Stop  sync Rate Control */
+	TXA_ENA_ARB	= 1<<1,	/* Enable  Tx Arbiter */
+	TXA_DIS_ARB	= 1<<0,	/* Disable Tx Arbiter */
+};
+
+/*
+ *	Bank 4 - 5
+ */
+/* Transmit Arbiter Registers MAC 1 and 2, use MR_ADDR() to access */
+enum {
+	TXA_ITI_INI	= 0x0200,/* 32 bit	Tx Arb Interval Timer Init Val*/
+	TXA_ITI_VAL	= 0x0204,/* 32 bit	Tx Arb Interval Timer Value */
+	TXA_LIM_INI	= 0x0208,/* 32 bit	Tx Arb Limit Counter Init Val */
+	TXA_LIM_VAL	= 0x020c,/* 32 bit	Tx Arb Limit Counter Value */
+	TXA_CTRL	= 0x0210,/*  8 bit	Tx Arbiter Control Register */
+	TXA_TEST	= 0x0211,/*  8 bit	Tx Arbiter Test Register */
+	TXA_STAT	= 0x0212,/*  8 bit	Tx Arbiter Status Register */
+};
+
+
+enum {
+	B6_EXT_REG	= 0x0300,/* External registers (GENESIS only) */
+	B7_CFG_SPC	= 0x0380,/* copy of the Configuration register */
+	B8_RQ1_REGS	= 0x0400,/* Receive Queue 1 */
+	B8_RQ2_REGS	= 0x0480,/* Receive Queue 2 */
+	B8_TS1_REGS	= 0x0600,/* Transmit sync queue 1 */
+	B8_TA1_REGS	= 0x0680,/* Transmit async queue 1 */
+	B8_TS2_REGS	= 0x0700,/* Transmit sync queue 2 */
+	B8_TA2_REGS	= 0x0780,/* Transmit sync queue 2 */
+	B16_RAM_REGS	= 0x0800,/* RAM Buffer Registers */
+};
+
+/* Queue Register Offsets, use Q_ADDR() to access */
+enum {
+	B8_Q_REGS = 0x0400, /* base of Queue registers */	
+	Q_D	= 0x00,	/* 8*32	bit	Current Descriptor */
+	Q_DA_L	= 0x20,	/* 32 bit	Current Descriptor Address Low dWord */
+	Q_DA_H	= 0x24,	/* 32 bit	Current Descriptor Address High dWord */
+	Q_AC_L	= 0x28,	/* 32 bit	Current Address Counter Low dWord */
+	Q_AC_H	= 0x2c,	/* 32 bit	Current Address Counter High dWord */
+	Q_BC	= 0x30,	/* 32 bit	Current Byte Counter */
+	Q_CSR	= 0x34,	/* 32 bit	BMU Control/Status Register */
+	Q_F	= 0x38,	/* 32 bit	Flag Register */
+	Q_T1	= 0x3c,	/* 32 bit	Test Register 1 */
+	Q_T1_TR	= 0x3c,	/*  8 bit	Test Register 1 Transfer SM */
+	Q_T1_WR	= 0x3d,	/*  8 bit	Test Register 1 Write Descriptor SM */
+	Q_T1_RD	= 0x3e,	/*  8 bit	Test Register 1 Read Descriptor SM */
+	Q_T1_SV	= 0x3f,	/*  8 bit	Test Register 1 Supervisor SM */
+	Q_T2	= 0x40,	/* 32 bit	Test Register 2	*/
+	Q_T3	= 0x44,	/* 32 bit	Test Register 3	*/
+
+/* Yukon-2 */
+	Q_DONE	= 0x24,	/* 16 bit	Done Index 		(Yukon-2 only) */
+	Q_WM	= 0x40,	/* 16 bit	FIFO Watermark */
+	Q_AL	= 0x42,	/*  8 bit	FIFO Alignment */
+	Q_RSP	= 0x44,	/* 16 bit	FIFO Read Shadow Pointer */
+	Q_RSL	= 0x46,	/*  8 bit	FIFO Read Shadow Level */
+	Q_RP	= 0x48,	/*  8 bit	FIFO Read Pointer */
+	Q_RL	= 0x4a,	/*  8 bit	FIFO Read Level */
+	Q_WP	= 0x4c,	/*  8 bit	FIFO Write Pointer */
+	Q_WSP	= 0x4d,	/*  8 bit	FIFO Write Shadow Pointer */
+	Q_WL	= 0x4e,	/*  8 bit	FIFO Write Level */
+	Q_WSL	= 0x4f,	/*  8 bit	FIFO Write Shadow Level */
+};
+#define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs))
+
+/* RAM Buffer Register Offsets */
+enum {
+
+	RB_START	= 0x00,/* 32 bit	RAM Buffer Start Address */
+	RB_END	= 0x04,/* 32 bit	RAM Buffer End Address */
+	RB_WP	= 0x08,/* 32 bit	RAM Buffer Write Pointer */
+	RB_RP	= 0x0c,/* 32 bit	RAM Buffer Read Pointer */
+	RB_RX_UTPP	= 0x10,/* 32 bit	Rx Upper Threshold, Pause Packet */
+	RB_RX_LTPP	= 0x14,/* 32 bit	Rx Lower Threshold, Pause Packet */
+	RB_RX_UTHP	= 0x18,/* 32 bit	Rx Upper Threshold, High Prio */
+	RB_RX_LTHP	= 0x1c,/* 32 bit	Rx Lower Threshold, High Prio */
+	/* 0x10 - 0x1f:	reserved at Tx RAM Buffer Registers */
+	RB_PC	= 0x20,/* 32 bit	RAM Buffer Packet Counter */
+	RB_LEV	= 0x24,/* 32 bit	RAM Buffer Level Register */
+	RB_CTRL	= 0x28,/* 32 bit	RAM Buffer Control Register */
+	RB_TST1	= 0x29,/*  8 bit	RAM Buffer Test Register 1 */
+	RB_TST2	= 0x2a,/*  8 bit	RAM Buffer Test Register 2 */
+};
+
+/* Receive and Transmit Queues */
+enum {
+	Q_R1	= 0x0000,	/* Receive Queue 1 */
+	Q_R2	= 0x0080,	/* Receive Queue 2 */
+	Q_XS1	= 0x0200,	/* Synchronous Transmit Queue 1 */
+	Q_XA1	= 0x0280,	/* Asynchronous Transmit Queue 1 */
+	Q_XS2	= 0x0300,	/* Synchronous Transmit Queue 2 */
+	Q_XA2	= 0x0380,	/* Asynchronous Transmit Queue 2 */
+};
+
+/* Different MAC Types */
+enum {
+	SK_MAC_XMAC =	0,	/* Xaqti XMAC II */
+	SK_MAC_GMAC =	1,	/* Marvell GMAC */
+};
+
+/* Different PHY Types */
+enum {
+	SK_PHY_XMAC	= 0,/* integrated in XMAC II */
+	SK_PHY_BCOM	= 1,/* Broadcom BCM5400 */
+	SK_PHY_LONE	= 2,/* Level One LXT1000  [not supported]*/
+	SK_PHY_NAT	= 3,/* National DP83891  [not supported] */
+	SK_PHY_MARV_COPPER= 4,/* Marvell 88E1011S */
+	SK_PHY_MARV_FIBER = 5,/* Marvell 88E1011S working on fiber */
+};
+
+/* PHY addresses (bits 12..8 of PHY address reg) */
+enum {
+	PHY_ADDR_XMAC	= 0<<8,
+	PHY_ADDR_BCOM	= 1<<8,
+	PHY_ADDR_LONE	= 3<<8,
+	PHY_ADDR_NAT	= 0<<8,
+/* GPHY address (bits 15..11 of SMI control reg) */
+	PHY_ADDR_MARV	= 0,
+};
+
+#define RB_ADDR(offs, queue) (B16_RAM_REGS + (queue) + (offs))
+
+/* Receive MAC FIFO, Receive LED, and Link_Sync regs (GENESIS only) */
+enum {
+	RX_MFF_EA	= 0x0c00,/* 32 bit	Receive MAC FIFO End Address */
+	RX_MFF_WP	= 0x0c04,/* 32 bit	Receive MAC FIFO Write Pointer */
+
+	RX_MFF_RP	= 0x0c0c,/* 32 bit	Receive MAC FIFO Read Pointer */
+	RX_MFF_PC	= 0x0c10,/* 32 bit	Receive MAC FIFO Packet Cnt */
+	RX_MFF_LEV	= 0x0c14,/* 32 bit	Receive MAC FIFO Level */
+	RX_MFF_CTRL1	= 0x0c18,/* 16 bit	Receive MAC FIFO Control Reg 1*/
+	RX_MFF_STAT_TO	= 0x0c1a,/*  8 bit	Receive MAC Status Timeout */
+	RX_MFF_TIST_TO	= 0x0c1b,/*  8 bit	Receive MAC Time Stamp Timeout */
+	RX_MFF_CTRL2	= 0x0c1c,/*  8 bit	Receive MAC FIFO Control Reg 2*/
+	RX_MFF_TST1	= 0x0c1d,/*  8 bit	Receive MAC FIFO Test Reg 1 */
+	RX_MFF_TST2	= 0x0c1e,/*  8 bit	Receive MAC FIFO Test Reg 2 */
+
+	RX_LED_INI	= 0x0c20,/* 32 bit	Receive LED Cnt Init Value */
+	RX_LED_VAL	= 0x0c24,/* 32 bit	Receive LED Cnt Current Value */
+	RX_LED_CTRL	= 0x0c28,/*  8 bit	Receive LED Cnt Control Reg */
+	RX_LED_TST	= 0x0c29,/*  8 bit	Receive LED Cnt Test Register */
+
+	LNK_SYNC_INI	= 0x0c30,/* 32 bit	Link Sync Cnt Init Value */
+	LNK_SYNC_VAL	= 0x0c34,/* 32 bit	Link Sync Cnt Current Value */
+	LNK_SYNC_CTRL	= 0x0c38,/*  8 bit	Link Sync Cnt Control Register */
+	LNK_SYNC_TST	= 0x0c39,/*  8 bit	Link Sync Cnt Test Register */
+	LNK_LED_REG	= 0x0c3c,/*  8 bit	Link LED Register */
+};
+
+/* Receive and Transmit MAC FIFO Registers (GENESIS only) */
+/*	RX_MFF_CTRL1	16 bit	Receive MAC FIFO Control Reg 1 */
+enum {
+	MFF_ENA_RDY_PAT	= 1<<13,	/* Enable  Ready Patch */
+	MFF_DIS_RDY_PAT	= 1<<12,	/* Disable Ready Patch */
+	MFF_ENA_TIM_PAT	= 1<<11,	/* Enable  Timing Patch */
+	MFF_DIS_TIM_PAT	= 1<<10,	/* Disable Timing Patch */
+	MFF_ENA_ALM_FUL	= 1<<9,	/* Enable  AlmostFull Sign */
+	MFF_DIS_ALM_FUL	= 1<<8,	/* Disable AlmostFull Sign */
+	MFF_ENA_PAUSE	= 1<<7,	/* Enable  Pause Signaling */
+	MFF_DIS_PAUSE	= 1<<6,	/* Disable Pause Signaling */
+	MFF_ENA_FLUSH	= 1<<5,	/* Enable  Frame Flushing */
+	MFF_DIS_FLUSH	= 1<<4,	/* Disable Frame Flushing */
+	MFF_ENA_TIST	= 1<<3,	/* Enable  Time Stamp Gener */
+	MFF_DIS_TIST	= 1<<2,	/* Disable Time Stamp Gener */
+	MFF_CLR_INTIST	= 1<<1,	/* Clear IRQ No Time Stamp */
+	MFF_CLR_INSTAT	= 1<<0,	/* Clear IRQ No Status */
+#define MFF_RX_CTRL_DEF MFF_ENA_TIM_PAT
+};
+
+/*	TX_MFF_CTRL1	16 bit	Transmit MAC FIFO Control Reg 1 */
+enum {
+	MFF_CLR_PERR	= 1<<15,	/* Clear Parity Error IRQ */
+								/* Bit 14:	reserved */
+	MFF_ENA_PKT_REC	= 1<<13,	/* Enable  Packet Recovery */
+	MFF_DIS_PKT_REC	= 1<<12,	/* Disable Packet Recovery */
+
+	MFF_ENA_W4E	= 1<<7,	/* Enable  Wait for Empty */
+	MFF_DIS_W4E	= 1<<6,	/* Disable Wait for Empty */
+
+	MFF_ENA_LOOPB	= 1<<3,	/* Enable  Loopback */
+	MFF_DIS_LOOPB	= 1<<2,	/* Disable Loopback */
+	MFF_CLR_MAC_RST	= 1<<1,	/* Clear XMAC Reset */
+	MFF_SET_MAC_RST	= 1<<0,	/* Set   XMAC Reset */
+};
+
+#define MFF_TX_CTRL_DEF	(MFF_ENA_PKT_REC | MFF_ENA_TIM_PAT | MFF_ENA_FLUSH)
+
+/*	RX_MFF_TST2	 	 8 bit	Receive MAC FIFO Test Register 2 */
+/*	TX_MFF_TST2	 	 8 bit	Transmit MAC FIFO Test Register 2 */
+enum {
+	MFF_WSP_T_ON	= 1<<6,	/* Tx: Write Shadow Ptr TestOn */
+	MFF_WSP_T_OFF	= 1<<5,	/* Tx: Write Shadow Ptr TstOff */
+	MFF_WSP_INC	= 1<<4,	/* Tx: Write Shadow Ptr Increment */
+	MFF_PC_DEC	= 1<<3,	/* Packet Counter Decrement */
+	MFF_PC_T_ON	= 1<<2,	/* Packet Counter Test On */
+	MFF_PC_T_OFF	= 1<<1,	/* Packet Counter Test Off */
+	MFF_PC_INC	= 1<<0,	/* Packet Counter Increment */
+};
+
+/*	RX_MFF_TST1	 	 8 bit	Receive MAC FIFO Test Register 1 */
+/*	TX_MFF_TST1	 	 8 bit	Transmit MAC FIFO Test Register 1 */
+enum {
+	MFF_WP_T_ON	= 1<<6,	/* Write Pointer Test On */
+	MFF_WP_T_OFF	= 1<<5,	/* Write Pointer Test Off */
+	MFF_WP_INC	= 1<<4,	/* Write Pointer Increm */
+
+	MFF_RP_T_ON	= 1<<2,	/* Read Pointer Test On */
+	MFF_RP_T_OFF	= 1<<1,	/* Read Pointer Test Off */
+	MFF_RP_DEC	= 1<<0,	/* Read Pointer Decrement */
+};
+
+/*	RX_MFF_CTRL2	 8 bit	Receive MAC FIFO Control Reg 2 */
+/*	TX_MFF_CTRL2	 8 bit	Transmit MAC FIFO Control Reg 2 */
+enum {
+	MFF_ENA_OP_MD	= 1<<3,	/* Enable  Operation Mode */
+	MFF_DIS_OP_MD	= 1<<2,	/* Disable Operation Mode */
+	MFF_RST_CLR	= 1<<1,	/* Clear MAC FIFO Reset */
+	MFF_RST_SET	= 1<<0,	/* Set   MAC FIFO Reset */
+};
+
+
+/*	Link LED Counter Registers (GENESIS only) */
+
+/*	RX_LED_CTRL		 8 bit	Receive LED Cnt Control Reg */
+/*	TX_LED_CTRL		 8 bit	Transmit LED Cnt Control Reg */
+/*	LNK_SYNC_CTRL	 8 bit	Link Sync Cnt Control Register */
+enum {
+	LED_START	= 1<<2,	/* Start Timer */
+	LED_STOP	= 1<<1,	/* Stop Timer */
+	LED_STATE	= 1<<0,	/* Rx/Tx: LED State, 1=LED on */
+};
+
+/*	RX_LED_TST		 8 bit	Receive LED Cnt Test Register */
+/*	TX_LED_TST		 8 bit	Transmit LED Cnt Test Register */
+/*	LNK_SYNC_TST	 8 bit	Link Sync Cnt Test Register */
+enum {
+	LED_T_ON	= 1<<2,	/* LED Counter Test mode On */
+	LED_T_OFF	= 1<<1,	/* LED Counter Test mode Off */
+	LED_T_STEP	= 1<<0,	/* LED Counter Step */
+};
+
+/*	LNK_LED_REG	 	 8 bit	Link LED Register */
+enum {
+	LED_BLK_ON	= 1<<5,	/* Link LED Blinking On */
+	LED_BLK_OFF	= 1<<4,	/* Link LED Blinking Off */
+	LED_SYNC_ON	= 1<<3,	/* Use Sync Wire to switch LED */
+	LED_SYNC_OFF	= 1<<2,	/* Disable Sync Wire Input */
+	LED_ON	= 1<<1,	/* switch LED on */
+	LED_OFF	= 1<<0,	/* switch LED off */
+};
+
+/* Receive GMAC FIFO (YUKON and Yukon-2) */
+enum {
+	RX_GMF_EA	= 0x0c40,/* 32 bit	Rx GMAC FIFO End Address */
+	RX_GMF_AF_THR	= 0x0c44,/* 32 bit	Rx GMAC FIFO Almost Full Thresh. */
+	RX_GMF_CTRL_T	= 0x0c48,/* 32 bit	Rx GMAC FIFO Control/Test */
+	RX_GMF_FL_MSK	= 0x0c4c,/* 32 bit	Rx GMAC FIFO Flush Mask */
+	RX_GMF_FL_THR	= 0x0c50,/* 32 bit	Rx GMAC FIFO Flush Threshold */
+	RX_GMF_TR_THR	= 0x0c54,/* 32 bit	Rx Truncation Threshold (Yukon-2) */
+
+	RX_GMF_VLAN	= 0x0c5c,/* 32 bit	Rx VLAN Type Register (Yukon-2) */
+	RX_GMF_WP	= 0x0c60,/* 32 bit	Rx GMAC FIFO Write Pointer */
+
+	RX_GMF_WLEV	= 0x0c68,/* 32 bit	Rx GMAC FIFO Write Level */
+
+	RX_GMF_RP	= 0x0c70,/* 32 bit	Rx GMAC FIFO Read Pointer */
+
+	RX_GMF_RLEV	= 0x0c78,/* 32 bit	Rx GMAC FIFO Read Level */
+};
+
+
+/*	TXA_TEST		 8 bit	Tx Arbiter Test Register */
+enum {
+	TXA_INT_T_ON	= 1<<5,	/* Tx Arb Interval Timer Test On */
+	TXA_INT_T_OFF	= 1<<4,	/* Tx Arb Interval Timer Test Off */
+	TXA_INT_T_STEP	= 1<<3,	/* Tx Arb Interval Timer Step */
+	TXA_LIM_T_ON	= 1<<2,	/* Tx Arb Limit Timer Test On */
+	TXA_LIM_T_OFF	= 1<<1,	/* Tx Arb Limit Timer Test Off */
+	TXA_LIM_T_STEP	= 1<<0,	/* Tx Arb Limit Timer Step */
+};
+
+/*	TXA_STAT		 8 bit	Tx Arbiter Status Register */
+enum {
+	TXA_PRIO_XS	= 1<<0,	/* sync queue has prio to send */
+};
+
+
+/*	Q_BC			32 bit	Current Byte Counter */
+
+/* BMU Control Status Registers */
+/*	B0_R1_CSR		32 bit	BMU Ctrl/Stat Rx Queue 1 */
+/*	B0_R2_CSR		32 bit	BMU Ctrl/Stat Rx Queue 2 */
+/*	B0_XA1_CSR		32 bit	BMU Ctrl/Stat Sync Tx Queue 1 */
+/*	B0_XS1_CSR		32 bit	BMU Ctrl/Stat Async Tx Queue 1 */
+/*	B0_XA2_CSR		32 bit	BMU Ctrl/Stat Sync Tx Queue 2 */
+/*	B0_XS2_CSR		32 bit	BMU Ctrl/Stat Async Tx Queue 2 */
+/*	Q_CSR			32 bit	BMU Control/Status Register */
+
+enum {
+	CSR_SV_IDLE	= 1<<24,	/* BMU SM Idle */
+
+	CSR_DESC_CLR	= 1<<21,	/* Clear Reset for Descr */
+	CSR_DESC_SET	= 1<<20,	/* Set   Reset for Descr */
+	CSR_FIFO_CLR	= 1<<19,	/* Clear Reset for FIFO */
+	CSR_FIFO_SET	= 1<<18,	/* Set   Reset for FIFO */
+	CSR_HPI_RUN	= 1<<17,	/* Release HPI SM */
+	CSR_HPI_RST	= 1<<16,	/* Reset   HPI SM to Idle */
+	CSR_SV_RUN	= 1<<15,	/* Release Supervisor SM */
+	CSR_SV_RST	= 1<<14,	/* Reset   Supervisor SM */
+	CSR_DREAD_RUN	= 1<<13,	/* Release Descr Read SM */
+	CSR_DREAD_RST	= 1<<12,	/* Reset   Descr Read SM */
+	CSR_DWRITE_RUN	= 1<<11,	/* Release Descr Write SM */
+	CSR_DWRITE_RST	= 1<<10,	/* Reset   Descr Write SM */
+	CSR_TRANS_RUN	= 1<<9,		/* Release Transfer SM */
+	CSR_TRANS_RST	= 1<<8,		/* Reset   Transfer SM */
+	CSR_ENA_POL	= 1<<7,		/* Enable  Descr Polling */
+	CSR_DIS_POL	= 1<<6,		/* Disable Descr Polling */
+	CSR_STOP	= 1<<5,		/* Stop  Rx/Tx Queue */
+	CSR_START	= 1<<4,		/* Start Rx/Tx Queue */
+	CSR_IRQ_CL_P	= 1<<3,		/* (Rx)	Clear Parity IRQ */
+	CSR_IRQ_CL_B	= 1<<2,		/* Clear EOB IRQ */
+	CSR_IRQ_CL_F	= 1<<1,		/* Clear EOF IRQ */
+	CSR_IRQ_CL_C	= 1<<0,		/* Clear ERR IRQ */
+};
+
+#define CSR_SET_RESET	(CSR_DESC_SET | CSR_FIFO_SET | CSR_HPI_RST |\
+			CSR_SV_RST | CSR_DREAD_RST | CSR_DWRITE_RST |\
+			CSR_TRANS_RST)
+#define CSR_CLR_RESET	(CSR_DESC_CLR | CSR_FIFO_CLR | CSR_HPI_RUN |\
+			CSR_SV_RUN | CSR_DREAD_RUN | CSR_DWRITE_RUN |\
+			CSR_TRANS_RUN)
+
+/*	Q_F				32 bit	Flag Register */
+enum {
+	F_ALM_FULL	= 1<<27,	/* Rx FIFO: almost full */
+	F_EMPTY		= 1<<27,	/* Tx FIFO: empty flag */
+	F_FIFO_EOF	= 1<<26,	/* Tag (EOF Flag) bit in FIFO */
+	F_WM_REACHED	= 1<<25,	/* Watermark reached */
+
+	F_FIFO_LEVEL	= 0x1fL<<16,	/* Bit 23..16:	# of Qwords in FIFO */
+	F_WATER_MARK	= 0x0007ffL,	/* Bit 10.. 0:	Watermark */
+};
+
+/* RAM Buffer Register Offsets, use RB_ADDR(Queue, Offs) to access */
+/*	RB_START		32 bit	RAM Buffer Start Address */
+/*	RB_END			32 bit	RAM Buffer End Address */
+/*	RB_WP			32 bit	RAM Buffer Write Pointer */
+/*	RB_RP			32 bit	RAM Buffer Read Pointer */
+/*	RB_RX_UTPP		32 bit	Rx Upper Threshold, Pause Pack */
+/*	RB_RX_LTPP		32 bit	Rx Lower Threshold, Pause Pack */
+/*	RB_RX_UTHP		32 bit	Rx Upper Threshold, High Prio */
+/*	RB_RX_LTHP		32 bit	Rx Lower Threshold, High Prio */
+/*	RB_PC			32 bit	RAM Buffer Packet Counter */
+/*	RB_LEV			32 bit	RAM Buffer Level Register */
+
+#define RB_MSK	0x0007ffff	/* Bit 18.. 0:	RAM Buffer Pointer Bits */
+/*	RB_TST2			 8 bit	RAM Buffer Test Register 2 */
+/*	RB_TST1			 8 bit	RAM Buffer Test Register 1 */
+
+/*	RB_CTRL			 8 bit	RAM Buffer Control Register */
+enum {
+	RB_ENA_STFWD	= 1<<5,	/* Enable  Store & Forward */
+	RB_DIS_STFWD	= 1<<4,	/* Disable Store & Forward */
+	RB_ENA_OP_MD	= 1<<3,	/* Enable  Operation Mode */
+	RB_DIS_OP_MD	= 1<<2,	/* Disable Operation Mode */
+	RB_RST_CLR	= 1<<1,	/* Clear RAM Buf STM Reset */
+	RB_RST_SET	= 1<<0,	/* Set   RAM Buf STM Reset */
+};
+
+/* Transmit MAC FIFO and Transmit LED Registers (GENESIS only), */
+enum {
+	TX_MFF_EA	= 0x0d00,/* 32 bit	Transmit MAC FIFO End Address */
+	TX_MFF_WP	= 0x0d04,/* 32 bit	Transmit MAC FIFO WR Pointer */
+	TX_MFF_WSP	= 0x0d08,/* 32 bit	Transmit MAC FIFO WR Shadow Ptr */
+	TX_MFF_RP	= 0x0d0c,/* 32 bit	Transmit MAC FIFO RD Pointer */
+	TX_MFF_PC	= 0x0d10,/* 32 bit	Transmit MAC FIFO Packet Cnt */
+	TX_MFF_LEV	= 0x0d14,/* 32 bit	Transmit MAC FIFO Level */
+	TX_MFF_CTRL1	= 0x0d18,/* 16 bit	Transmit MAC FIFO Ctrl Reg 1 */
+	TX_MFF_WAF	= 0x0d1a,/*  8 bit	Transmit MAC Wait after flush */
+
+	TX_MFF_CTRL2	= 0x0d1c,/*  8 bit	Transmit MAC FIFO Ctrl Reg 2 */
+	TX_MFF_TST1	= 0x0d1d,/*  8 bit	Transmit MAC FIFO Test Reg 1 */
+	TX_MFF_TST2	= 0x0d1e,/*  8 bit	Transmit MAC FIFO Test Reg 2 */
+
+	TX_LED_INI	= 0x0d20,/* 32 bit	Transmit LED Cnt Init Value */
+	TX_LED_VAL	= 0x0d24,/* 32 bit	Transmit LED Cnt Current Val */
+	TX_LED_CTRL	= 0x0d28,/*  8 bit	Transmit LED Cnt Control Reg */
+	TX_LED_TST	= 0x0d29,/*  8 bit	Transmit LED Cnt Test Reg */
+};
+
+/* Counter and Timer constants, for a host clock of 62.5 MHz */
+#define SK_XMIT_DUR		0x002faf08UL	/*  50 ms */
+#define SK_BLK_DUR		0x01dcd650UL	/* 500 ms */
+
+#define SK_DPOLL_DEF	0x00ee6b28UL	/* 250 ms at 62.5 MHz */
+
+#define SK_DPOLL_MAX	0x00ffffffUL	/* 268 ms at 62.5 MHz */
+					/* 215 ms at 78.12 MHz */
+
+#define SK_FACT_62		100	/* is given in percent */
+#define SK_FACT_53		 85     /* on GENESIS:	53.12 MHz */
+#define SK_FACT_78		125	/* on YUKON:	78.12 MHz */
+
+
+/* Transmit GMAC FIFO (YUKON only) */
+enum {
+	TX_GMF_EA	= 0x0d40,/* 32 bit	Tx GMAC FIFO End Address */
+	TX_GMF_AE_THR	= 0x0d44,/* 32 bit	Tx GMAC FIFO Almost Empty Thresh.*/
+	TX_GMF_CTRL_T	= 0x0d48,/* 32 bit	Tx GMAC FIFO Control/Test */
+
+	TX_GMF_WP	= 0x0d60,/* 32 bit 	Tx GMAC FIFO Write Pointer */
+	TX_GMF_WSP	= 0x0d64,/* 32 bit 	Tx GMAC FIFO Write Shadow Ptr. */
+	TX_GMF_WLEV	= 0x0d68,/* 32 bit 	Tx GMAC FIFO Write Level */
+
+	TX_GMF_RP	= 0x0d70,/* 32 bit 	Tx GMAC FIFO Read Pointer */
+	TX_GMF_RSTP	= 0x0d74,/* 32 bit 	Tx GMAC FIFO Restart Pointer */
+	TX_GMF_RLEV	= 0x0d78,/* 32 bit 	Tx GMAC FIFO Read Level */
+
+	/* Descriptor Poll Timer Registers */
+	B28_DPT_INI	= 0x0e00,/* 24 bit	Descriptor Poll Timer Init Val */
+	B28_DPT_VAL	= 0x0e04,/* 24 bit	Descriptor Poll Timer Curr Val */
+	B28_DPT_CTRL	= 0x0e08,/*  8 bit	Descriptor Poll Timer Ctrl Reg */
+
+	B28_DPT_TST	= 0x0e0a,/*  8 bit	Descriptor Poll Timer Test Reg */
+
+	/* Time Stamp Timer Registers (YUKON only) */
+	GMAC_TI_ST_VAL	= 0x0e14,/* 32 bit	Time Stamp Timer Curr Val */
+	GMAC_TI_ST_CTRL	= 0x0e18,/*  8 bit	Time Stamp Timer Ctrl Reg */
+	GMAC_TI_ST_TST	= 0x0e1a,/*  8 bit	Time Stamp Timer Test Reg */
+};
+
+/* Status BMU Registers (Yukon-2 only)*/
+enum {
+	STAT_CTRL	= 0x0e80,/* 32 bit	Status BMU Control Reg */
+	STAT_LAST_IDX	= 0x0e84,/* 16 bit	Status BMU Last Index */
+	/* 0x0e85 - 0x0e86:	reserved */
+	STAT_LIST_ADDR_LO	= 0x0e88,/* 32 bit	Status List Start Addr (low) */
+	STAT_LIST_ADDR_HI	= 0x0e8c,/* 32 bit	Status List Start Addr (high) */
+	STAT_TXA1_RIDX	= 0x0e90,/* 16 bit	Status TxA1 Report Index Reg */
+	STAT_TXS1_RIDX	= 0x0e92,/* 16 bit	Status TxS1 Report Index Reg */
+	STAT_TXA2_RIDX	= 0x0e94,/* 16 bit	Status TxA2 Report Index Reg */
+	STAT_TXS2_RIDX	= 0x0e96,/* 16 bit	Status TxS2 Report Index Reg */
+	STAT_TX_IDX_TH	= 0x0e98,/* 16 bit	Status Tx Index Threshold Reg */
+	STAT_PUT_IDX	= 0x0e9c,/* 16 bit	Status Put Index Reg */
+
+/* FIFO Control/Status Re