Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 3463 insertions, 0 deletions

diff --git a/drivers/net/defxx.c b/drivers/net/defxx.c
new file mode 100644
index 00000000000..a6aa56598f2
--- /dev/null
+++ b/drivers/net/defxx.c
@@ -0,0 +1,3463 @@
+/*
+ * File Name:
+ *   defxx.c
+ *
+ * Copyright Information:
+ *   Copyright Digital Equipment Corporation 1996.
+ *
+ *   This software may be used and distributed according to the terms of
+ *   the GNU General Public License, incorporated herein by reference.
+ *
+ * Abstract:
+ *   A Linux device driver supporting the Digital Equipment Corporation
+ *   FDDI EISA and PCI controller families.  Supported adapters include:
+ *
+ *		DEC FDDIcontroller/EISA (DEFEA)
+ *		DEC FDDIcontroller/PCI  (DEFPA)
+ *
+ * The original author:
+ *   LVS	Lawrence V. Stefani <lstefani@yahoo.com>
+ *
+ * Maintainers:
+ *   macro	Maciej W. Rozycki <macro@linux-mips.org>
+ *
+ * Credits:
+ *   I'd like to thank Patricia Cross for helping me get started with
+ *   Linux, David Davies for a lot of help upgrading and configuring
+ *   my development system and for answering many OS and driver
+ *   development questions, and Alan Cox for recommendations and
+ *   integration help on getting FDDI support into Linux.  LVS
+ *
+ * Driver Architecture:
+ *   The driver architecture is largely based on previous driver work
+ *   for other operating systems.  The upper edge interface and
+ *   functions were largely taken from existing Linux device drivers
+ *   such as David Davies' DE4X5.C driver and Donald Becker's TULIP.C
+ *   driver.
+ *
+ *   Adapter Probe -
+ *		The driver scans for supported EISA adapters by reading the
+ *		SLOT ID register for each EISA slot and making a match
+ *		against the expected value.
+ *
+ *   Bus-Specific Initialization -
+ *		This driver currently supports both EISA and PCI controller
+ *		families.  While the custom DMA chip and FDDI logic is similar
+ *		or identical, the bus logic is very different.  After
+ *		initialization, the	only bus-specific differences is in how the
+ *		driver enables and disables interrupts.  Other than that, the
+ *		run-time critical code behaves the same on both families.
+ *		It's important to note that both adapter families are configured
+ *		to I/O map, rather than memory map, the adapter registers.
+ *
+ *   Driver Open/Close -
+ *		In the driver open routine, the driver ISR (interrupt service
+ *		routine) is registered and the adapter is brought to an
+ *		operational state.  In the driver close routine, the opposite
+ *		occurs; the driver ISR is deregistered and the adapter is
+ *		brought to a safe, but closed state.  Users may use consecutive
+ *		commands to bring the adapter up and down as in the following
+ *		example:
+ *					ifconfig fddi0 up
+ *					ifconfig fddi0 down
+ *					ifconfig fddi0 up
+ *
+ *   Driver Shutdown -
+ *		Apparently, there is no shutdown or halt routine support under
+ *		Linux.  This routine would be called during "reboot" or
+ *		"shutdown" to allow the driver to place the adapter in a safe
+ *		state before a warm reboot occurs.  To be really safe, the user
+ *		should close the adapter before shutdown (eg. ifconfig fddi0 down)
+ *		to ensure that the adapter DMA engine is taken off-line.  However,
+ *		the current driver code anticipates this problem and always issues
+ *		a soft reset of the adapter	at the beginning of driver initialization.
+ *		A future driver enhancement in this area may occur in 2.1.X where
+ *		Alan indicated that a shutdown handler may be implemented.
+ *
+ *   Interrupt Service Routine -
+ *		The driver supports shared interrupts, so the ISR is registered for
+ *		each board with the appropriate flag and the pointer to that board's
+ *		device structure.  This provides the context during interrupt
+ *		processing to support shared interrupts and multiple boards.
+ *
+ *		Interrupt enabling/disabling can occur at many levels.  At the host
+ *		end, you can disable system interrupts, or disable interrupts at the
+ *		PIC (on Intel systems).  Across the bus, both EISA and PCI adapters
+ *		have a bus-logic chip interrupt enable/disable as well as a DMA
+ *		controller interrupt enable/disable.
+ *
+ *		The driver currently enables and disables adapter interrupts at the
+ *		bus-logic chip and assumes that Linux will take care of clearing or
+ *		acknowledging any host-based interrupt chips.
+ *
+ *   Control Functions -
+ *		Control functions are those used to support functions such as adding
+ *		or deleting multicast addresses, enabling or disabling packet
+ *		reception filters, or other custom/proprietary commands.  Presently,
+ *		the driver supports the "get statistics", "set multicast list", and
+ *		"set mac address" functions defined by Linux.  A list of possible
+ *		enhancements include:
+ *
+ *				- Custom ioctl interface for executing port interface commands
+ *				- Custom ioctl interface for adding unicast addresses to
+ *				  adapter CAM (to support bridge functions).
+ *				- Custom ioctl interface for supporting firmware upgrades.
+ *
+ *   Hardware (port interface) Support Routines -
+ *		The driver function names that start with "dfx_hw_" represent
+ *		low-level port interface routines that are called frequently.  They
+ *		include issuing a DMA or port control command to the adapter,
+ *		resetting the adapter, or reading the adapter state.  Since the
+ *		driver initialization and run-time code must make calls into the
+ *		port interface, these routines were written to be as generic and
+ *		usable as possible.
+ *
+ *   Receive Path -
+ *		The adapter DMA engine supports a 256 entry receive descriptor block
+ *		of which up to 255 entries can be used at any given time.  The
+ *		architecture is a standard producer, consumer, completion model in
+ *		which the driver "produces" receive buffers to the adapter, the
+ *		adapter "consumes" the receive buffers by DMAing incoming packet data,
+ *		and the driver "completes" the receive buffers by servicing the
+ *		incoming packet, then "produces" a new buffer and starts the cycle
+ *		again.  Receive buffers can be fragmented in up to 16 fragments
+ *		(descriptor	entries).  For simplicity, this driver posts
+ *		single-fragment receive buffers of 4608 bytes, then allocates a
+ *		sk_buff, copies the data, then reposts the buffer.  To reduce CPU
+ *		utilization, a better approach would be to pass up the receive
+ *		buffer (no extra copy) then allocate and post a replacement buffer.
+ *		This is a performance enhancement that should be looked into at
+ *		some point.
+ *
+ *   Transmit Path -
+ *		Like the receive path, the adapter DMA engine supports a 256 entry
+ *		transmit descriptor block of which up to 255 entries can be used at
+ *		any	given time.  Transmit buffers can be fragmented	in up to 255
+ *		fragments (descriptor entries).  This driver always posts one
+ *		fragment per transmit packet request.
+ *
+ *		The fragment contains the entire packet from FC to end of data.
+ *		Before posting the buffer to the adapter, the driver sets a three-byte
+ *		packet request header (PRH) which is required by the Motorola MAC chip
+ *		used on the adapters.  The PRH tells the MAC the type of token to
+ *		receive/send, whether or not to generate and append the CRC, whether
+ *		synchronous or asynchronous framing is used, etc.  Since the PRH
+ *		definition is not necessarily consistent across all FDDI chipsets,
+ *		the driver, rather than the common FDDI packet handler routines,
+ *		sets these bytes.
+ *
+ *		To reduce the amount of descriptor fetches needed per transmit request,
+ *		the driver takes advantage of the fact that there are at least three
+ *		bytes available before the skb->data field on the outgoing transmit
+ *		request.  This is guaranteed by having fddi_setup() in net_init.c set
+ *		dev->hard_header_len to 24 bytes.  21 bytes accounts for the largest
+ *		header in an 802.2 SNAP frame.  The other 3 bytes are the extra "pad"
+ *		bytes which we'll use to store the PRH.
+ *
+ *		There's a subtle advantage to adding these pad bytes to the
+ *		hard_header_len, it ensures that the data portion of the packet for
+ *		an 802.2 SNAP frame is longword aligned.  Other FDDI driver
+ *		implementations may not need the extra padding and can start copying
+ *		or DMAing directly from the FC byte which starts at skb->data.  Should
+ *		another driver implementation need ADDITIONAL padding, the net_init.c
+ *		module should be updated and dev->hard_header_len should be increased.
+ *		NOTE: To maintain the alignment on the data portion of the packet,
+ *		dev->hard_header_len should always be evenly divisible by 4 and at
+ *		least 24 bytes in size.
+ *
+ * Modification History:
+ *		Date		Name	Description
+ *		16-Aug-96	LVS		Created.
+ *		20-Aug-96	LVS		Updated dfx_probe so that version information
+ *							string is only displayed if 1 or more cards are
+ *							found.  Changed dfx_rcv_queue_process to copy
+ *							3 NULL bytes before FC to ensure that data is
+ *							longword aligned in receive buffer.
+ *		09-Sep-96	LVS		Updated dfx_ctl_set_multicast_list to enable
+ *							LLC group promiscuous mode if multicast list
+ *							is too large.  LLC individual/group promiscuous
+ *							mode is now disabled if IFF_PROMISC flag not set.
+ *							dfx_xmt_queue_pkt no longer checks for NULL skb
+ *							on Alan Cox recommendation.  Added node address
+ *							override support.
+ *		12-Sep-96	LVS		Reset current address to factory address during
+ *							device open.  Updated transmit path to post a
+ *							single fragment which includes PRH->end of data.
+ *		Mar 2000	AC		Did various cleanups for 2.3.x
+ *		Jun 2000	jgarzik		PCI and resource alloc cleanups
+ *		Jul 2000	tjeerd		Much cleanup and some bug fixes
+ *		Sep 2000	tjeerd		Fix leak on unload, cosmetic code cleanup
+ *		Feb 2001			Skb allocation fixes
+ *		Feb 2001	davej		PCI enable cleanups.
+ *		04 Aug 2003	macro		Converted to the DMA API.
+ *		14 Aug 2004	macro		Fix device names reported.
+ */
+
+/* Include files */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/errno.h>
+#include <linux/ioport.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/pci.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/netdevice.h>
+#include <linux/fddidevice.h>
+#include <linux/skbuff.h>
+#include <linux/bitops.h>
+
+#include <asm/byteorder.h>
+#include <asm/io.h>
+
+#include "defxx.h"
+
+/* Version information string should be updated prior to each new release!  */
+#define DRV_NAME "defxx"
+#define DRV_VERSION "v1.07"
+#define DRV_RELDATE "2004/08/14"
+
+static char version[] __devinitdata =
+	DRV_NAME ": " DRV_VERSION " " DRV_RELDATE
+	"  Lawrence V. Stefani and others\n";
+
+#define DYNAMIC_BUFFERS 1
+
+#define SKBUFF_RX_COPYBREAK 200
+/*
+ * NEW_SKB_SIZE = PI_RCV_DATA_K_SIZE_MAX+128 to allow 128 byte
+ * alignment for compatibility with old EISA boards.
+ */
+#define NEW_SKB_SIZE (PI_RCV_DATA_K_SIZE_MAX+128)
+
+/* Define module-wide (static) routines */
+
+static void		dfx_bus_init(struct net_device *dev);
+static void		dfx_bus_config_check(DFX_board_t *bp);
+
+static int		dfx_driver_init(struct net_device *dev, const char *print_name);
+static int		dfx_adap_init(DFX_board_t *bp, int get_buffers);
+
+static int		dfx_open(struct net_device *dev);
+static int		dfx_close(struct net_device *dev);
+
+static void		dfx_int_pr_halt_id(DFX_board_t *bp);
+static void		dfx_int_type_0_process(DFX_board_t *bp);
+static void		dfx_int_common(struct net_device *dev);
+static void		dfx_interrupt(int irq, void *dev_id, struct pt_regs *regs);
+
+static struct		net_device_stats *dfx_ctl_get_stats(struct net_device *dev);
+static void		dfx_ctl_set_multicast_list(struct net_device *dev);
+static int		dfx_ctl_set_mac_address(struct net_device *dev, void *addr);
+static int		dfx_ctl_update_cam(DFX_board_t *bp);
+static int		dfx_ctl_update_filters(DFX_board_t *bp);
+
+static int		dfx_hw_dma_cmd_req(DFX_board_t *bp);
+static int		dfx_hw_port_ctrl_req(DFX_board_t *bp, PI_UINT32	command, PI_UINT32 data_a, PI_UINT32 data_b, PI_UINT32 *host_data);
+static void		dfx_hw_adap_reset(DFX_board_t *bp, PI_UINT32 type);
+static int		dfx_hw_adap_state_rd(DFX_board_t *bp);
+static int		dfx_hw_dma_uninit(DFX_board_t *bp, PI_UINT32 type);
+
+static int		dfx_rcv_init(DFX_board_t *bp, int get_buffers);
+static void		dfx_rcv_queue_process(DFX_board_t *bp);
+static void		dfx_rcv_flush(DFX_board_t *bp);
+
+static int		dfx_xmt_queue_pkt(struct sk_buff *skb, struct net_device *dev);
+static int		dfx_xmt_done(DFX_board_t *bp);
+static void		dfx_xmt_flush(DFX_board_t *bp);
+
+/* Define module-wide (static) variables */
+
+static struct net_device *root_dfx_eisa_dev;
+
+
+/*
+ * =======================
+ * = dfx_port_write_byte =
+ * = dfx_port_read_byte	 =
+ * = dfx_port_write_long =
+ * = dfx_port_read_long  =
+ * =======================
+ *   
+ * Overview:
+ *   Routines for reading and writing values from/to adapter
+ *  
+ * Returns:
+ *   None
+ *       
+ * Arguments:
+ *   bp     - pointer to board information
+ *   offset - register offset from base I/O address
+ *   data   - for dfx_port_write_byte and dfx_port_write_long, this
+ *			  is a value to write.
+ *			  for dfx_port_read_byte and dfx_port_read_byte, this
+ *			  is a pointer to store the read value.
+ *
+ * Functional Description:
+ *   These routines perform the correct operation to read or write
+ *   the adapter register.
+ *   
+ *   EISA port block base addresses are based on the slot number in which the
+ *   controller is installed.  For example, if the EISA controller is installed
+ *   in slot 4, the port block base address is 0x4000.  If the controller is
+ *   installed in slot 2, the port block base address is 0x2000, and so on.
+ *   This port block can be used to access PDQ, ESIC, and DEFEA on-board
+ *   registers using the register offsets defined in DEFXX.H.
+ *
+ *   PCI port block base addresses are assigned by the PCI BIOS or system
+ *	 firmware.  There is one 128 byte port block which can be accessed.  It
+ *   allows for I/O mapping of both PDQ and PFI registers using the register
+ *   offsets defined in DEFXX.H.
+ *
+ * Return Codes:
+ *   None
+ *
+ * Assumptions:
+ *   bp->base_addr is a valid base I/O address for this adapter.
+ *   offset is a valid register offset for this adapter.
+ *
+ * Side Effects:
+ *   Rather than produce macros for these functions, these routines
+ *   are defined using "inline" to ensure that the compiler will
+ *   generate inline code and not waste a procedure call and return.
+ *   This provides all the benefits of macros, but with the
+ *   advantage of strict data type checking.
+ */
+
+static inline void dfx_port_write_byte(
+	DFX_board_t	*bp,
+	int			offset,
+	u8			data
+	)
+
+	{
+	u16 port = bp->base_addr + offset;
+
+	outb(data, port);
+	}
+
+static inline void dfx_port_read_byte(
+	DFX_board_t	*bp,
+	int			offset,
+	u8			*data
+	)
+
+	{
+	u16 port = bp->base_addr + offset;
+
+	*data = inb(port);
+	}
+
+static inline void dfx_port_write_long(
+	DFX_board_t	*bp,
+	int			offset,
+	u32			data
+	)
+
+	{
+	u16 port = bp->base_addr + offset;
+
+	outl(data, port);
+	}
+
+static inline void dfx_port_read_long(
+	DFX_board_t	*bp,
+	int			offset,
+	u32			*data
+	)
+
+	{
+	u16 port = bp->base_addr + offset;
+
+	*data = inl(port);
+	}
+
+
+/*
+ * =============
+ * = dfx_init_one_pci_or_eisa =
+ * =============
+ *   
+ * Overview:
+ *   Initializes a supported FDDI EISA or PCI controller
+ *  
+ * Returns:
+ *   Condition code
+ *       
+ * Arguments:
+ *   pdev - pointer to pci device information (NULL for EISA)
+ *   ioaddr - pointer to port (NULL for PCI)
+ *
+ * Functional Description:
+ *
+ * Return Codes:
+ *   0		 - This device (fddi0, fddi1, etc) configured successfully
+ *   -EBUSY      - Failed to get resources, or dfx_driver_init failed.
+ *
+ * Assumptions:
+ *   It compiles so it should work :-( (PCI cards do :-)
+ *
+ * Side Effects:
+ *   Device structures for FDDI adapters (fddi0, fddi1, etc) are
+ *   initialized and the board resources are read and stored in
+ *   the device structure.
+ */
+static int __devinit dfx_init_one_pci_or_eisa(struct pci_dev *pdev, long ioaddr)
+{
+	static int version_disp;
+	char *print_name = DRV_NAME;
+	struct net_device *dev;
+	DFX_board_t	  *bp;			/* board pointer */
+	int alloc_size;				/* total buffer size used */
+	int err;
+
+	if (!version_disp) {	/* display version info if adapter is found */
+		version_disp = 1;	/* set display flag to TRUE so that */
+		printk(version);	/* we only display this string ONCE */
+	}
+
+	if (pdev != NULL)
+		print_name = pci_name(pdev);
+
+	dev = alloc_fddidev(sizeof(*bp));
+	if (!dev) {
+		printk(KERN_ERR "%s: unable to allocate fddidev, aborting\n",
+		       print_name);
+		return -ENOMEM;
+	}
+
+	/* Enable PCI device. */
+	if (pdev != NULL) {
+		err = pci_enable_device (pdev);
+		if (err) goto err_out;
+		ioaddr = pci_resource_start (pdev, 1);
+	}
+
+	SET_MODULE_OWNER(dev);
+	SET_NETDEV_DEV(dev, &pdev->dev);
+
+	bp = dev->priv;
+
+	if (!request_region(ioaddr,
+			    pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN,
+			    print_name)) {
+		printk(KERN_ERR "%s: Cannot reserve I/O resource "
+		       "0x%x @ 0x%lx, aborting\n", print_name,
+		       pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN, ioaddr);
+		err = -EBUSY;
+		goto err_out;
+	}
+
+	/* Initialize new device structure */
+
+	dev->base_addr			= ioaddr; /* save port (I/O) base address */
+
+	dev->get_stats			= dfx_ctl_get_stats;
+	dev->open			= dfx_open;
+	dev->stop			= dfx_close;
+	dev->hard_start_xmit		= dfx_xmt_queue_pkt;
+	dev->set_multicast_list		= dfx_ctl_set_multicast_list;
+	dev->set_mac_address		= dfx_ctl_set_mac_address;
+
+	if (pdev == NULL) {
+		/* EISA board */
+		bp->bus_type = DFX_BUS_TYPE_EISA;
+		bp->next = root_dfx_eisa_dev;
+		root_dfx_eisa_dev = dev;
+	} else {
+		/* PCI board */
+		bp->bus_type = DFX_BUS_TYPE_PCI;
+		bp->pci_dev = pdev;
+		pci_set_drvdata (pdev, dev);
+		pci_set_master (pdev);
+	}
+
+	if (dfx_driver_init(dev, print_name) != DFX_K_SUCCESS) {
+		err = -ENODEV;
+		goto err_out_region;
+	}
+
+	err = register_netdev(dev);
+	if (err)
+		goto err_out_kfree;
+
+	printk("%s: registered as %s\n", print_name, dev->name);
+	return 0;
+
+err_out_kfree:
+	alloc_size = sizeof(PI_DESCR_BLOCK) +
+		     PI_CMD_REQ_K_SIZE_MAX + PI_CMD_RSP_K_SIZE_MAX +
+#ifndef DYNAMIC_BUFFERS
+		     (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) +
+#endif
+		     sizeof(PI_CONSUMER_BLOCK) +
+		     (PI_ALIGN_K_DESC_BLK - 1);
+	if (bp->kmalloced)
+		pci_free_consistent(pdev, alloc_size,
+				    bp->kmalloced, bp->kmalloced_dma);
+err_out_region:
+	release_region(ioaddr, pdev ? PFI_K_CSR_IO_LEN : PI_ESIC_K_CSR_IO_LEN);
+err_out:
+	free_netdev(dev);
+	return err;
+}
+
+static int __devinit dfx_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+	return dfx_init_one_pci_or_eisa(pdev, 0);
+}
+
+static int __init dfx_eisa_init(void)
+{
+	int rc = -ENODEV;
+	int i;			/* used in for loops */
+	u16 port;		/* temporary I/O (port) address */
+	u32 slot_id;		/* EISA hardware (slot) ID read from adapter */
+
+	DBG_printk("In dfx_eisa_init...\n");
+
+	/* Scan for FDDI EISA controllers */
+
+	for (i=0; i < DFX_MAX_EISA_SLOTS; i++)		/* only scan for up to 16 EISA slots */
+	{
+		port = (i << 12) + PI_ESIC_K_SLOT_ID;	/* port = I/O address for reading slot ID */
+		slot_id = inl(port);					/* read EISA HW (slot) ID */
+		if ((slot_id & 0xF0FFFFFF) == DEFEA_PRODUCT_ID)
+		{
+			port = (i << 12);					/* recalc base addr */
+
+			if (dfx_init_one_pci_or_eisa(NULL, port) == 0) rc = 0;
+		}
+	}
+	return rc;
+}
+
+/*
+ * ================
+ * = dfx_bus_init =
+ * ================
+ *   
+ * Overview:
+ *   Initializes EISA and PCI controller bus-specific logic.
+ *  
+ * Returns:
+ *   None
+ *       
+ * Arguments:
+ *   dev - pointer to device information
+ *
+ * Functional Description:
+ *   Determine and save adapter IRQ in device table,
+ *   then perform bus-specific logic initialization.
+ *
+ * Return Codes:
+ *   None
+ *
+ * Assumptions:
+ *   dev->base_addr has already been set with the proper
+ *	 base I/O address for this device.
+ *
+ * Side Effects:
+ *   Interrupts are enabled at the adapter bus-specific logic.
+ *   Note:  Interrupts at the DMA engine (PDQ chip) are not
+ *   enabled yet.
+ */
+
+static void __devinit dfx_bus_init(struct net_device *dev)
+{
+	DFX_board_t *bp = dev->priv;
+	u8			val;	/* used for I/O read/writes */
+
+	DBG_printk("In dfx_bus_init...\n");
+
+	/*
+	 * Initialize base I/O address field in bp structure
+	 *
+	 * Note: bp->base_addr is the same as dev->base_addr.
+	 *		 It's useful because often we'll need to read
+	 *		 or write registers where we already have the
+	 *		 bp pointer instead of the dev pointer.  Having
+	 *		 the base address in the bp structure will
+	 *		 save a pointer dereference.
+	 *
+	 *		 IMPORTANT!! This field must be defined before
+	 *		 any of the dfx_port_* inline functions are
+	 *		 called.
+	 */
+
+	bp->base_addr = dev->base_addr;
+
+	/* And a pointer back to the net_device struct */
+	bp->dev = dev;
+
+	/* Initialize adapter based on bus type */
+
+	if (bp->bus_type == DFX_BUS_TYPE_EISA)
+		{
+		/* Get the interrupt level from the ESIC chip */
+
+		dfx_port_read_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, &val);
+		switch ((val & PI_CONFIG_STAT_0_M_IRQ) >> PI_CONFIG_STAT_0_V_IRQ)
+			{
+			case PI_CONFIG_STAT_0_IRQ_K_9:
+				dev->irq = 9;
+				break;
+
+			case PI_CONFIG_STAT_0_IRQ_K_10:
+				dev->irq = 10;
+				break;
+
+			case PI_CONFIG_STAT_0_IRQ_K_11:
+				dev->irq = 11;
+				break;
+
+			case PI_CONFIG_STAT_0_IRQ_K_15:
+				dev->irq = 15;
+				break;
+			}
+
+		/* Enable access to I/O on the board by writing 0x03 to Function Control Register */
+
+		dfx_port_write_byte(bp, PI_ESIC_K_FUNCTION_CNTRL, PI_ESIC_K_FUNCTION_CNTRL_IO_ENB);
+
+		/* Set the I/O decode range of the board */
+
+		val = ((dev->base_addr >> 12) << PI_IO_CMP_V_SLOT);
+		dfx_port_write_byte(bp, PI_ESIC_K_IO_CMP_0_1, val);
+		dfx_port_write_byte(bp, PI_ESIC_K_IO_CMP_1_1, val);
+
+		/* Enable access to rest of module (including PDQ and packet memory) */
+
+		dfx_port_write_byte(bp, PI_ESIC_K_SLOT_CNTRL, PI_SLOT_CNTRL_M_ENB);
+
+		/*
+		 * Map PDQ registers into I/O space.  This is done by clearing a bit
+		 * in Burst Holdoff register.
+		 */
+
+		dfx_port_read_byte(bp, PI_ESIC_K_BURST_HOLDOFF, &val);
+		dfx_port_write_byte(bp, PI_ESIC_K_BURST_HOLDOFF, (val & ~PI_BURST_HOLDOFF_M_MEM_MAP));
+
+		/* Enable interrupts at EISA bus interface chip (ESIC) */
+
+		dfx_port_read_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, &val);
+		dfx_port_write_byte(bp, PI_ESIC_K_IO_CONFIG_STAT_0, (val | PI_CONFIG_STAT_0_M_INT_ENB));
+		}
+	else
+		{
+		struct pci_dev *pdev = bp->pci_dev;
+
+		/* Get the interrupt level from the PCI Configuration Table */
+
+		dev->irq = pdev->irq;
+
+		/* Check Latency Timer and set if less than minimal */
+
+		pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &val);
+		if (val < PFI_K_LAT_TIMER_MIN)	/* if less than min, override with default */
+			{
+			val = PFI_K_LAT_TIMER_DEF;
+			pci_write_config_byte(pdev, PCI_LATENCY_TIMER, val);
+			}
+
+		/* Enable interrupts at PCI bus interface chip (PFI) */
+
+		dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, (PFI_MODE_M_PDQ_INT_ENB | PFI_MODE_M_DMA_ENB));
+		}
+	}
+
+
+/*
+ * ========================
+ * = dfx_bus_config_check =
+ * ========================
+ *   
+ * Overview:
+ *   Checks the configuration (burst size, full-duplex, etc.)  If any parameters
+ *   are illegal, then this routine will set new defaults.
+ *  
+ * Returns:
+ *   None
+ *       
+ * Arguments:
+ *   bp - pointer to board information
+ *
+ * Functional Description:
+ *   For Revision 1 FDDI EISA, Revision 2 or later FDDI EISA with rev E or later
+ *   PDQ, and all FDDI PCI controllers, all values are legal.
+ *
+ * Return Codes:
+ *   None
+ *
+ * Assumptions:
+ *   dfx_adap_init has NOT been called yet so burst size and other items have
+ *   not been set.
+ *
+ * Side Effects:
+ *   None
+ */
+
+static void __devinit dfx_bus_config_check(DFX_board_t *bp)
+{
+	int	status;				/* return code from adapter port control call */
+	u32	slot_id;			/* EISA-bus hardware id (DEC3001, DEC3002,...) */
+	u32	host_data;			/* LW data returned from port control call */
+
+	DBG_printk("In dfx_bus_config_check...\n");
+
+	/* Configuration check only valid for EISA adapter */
+
+	if (bp->bus_type == DFX_BUS_TYPE_EISA)
+		{
+		dfx_port_read_long(bp, PI_ESIC_K_SLOT_ID, &slot_id);
+
+		/*
+		 * First check if revision 2 EISA controller.  Rev. 1 cards used
+		 * PDQ revision B, so no workaround needed in this case.  Rev. 3
+		 * cards used PDQ revision E, so no workaround needed in this
+		 * case, either.  Only Rev. 2 cards used either Rev. D or E
+		 * chips, so we must verify the chip revision on Rev. 2 cards.
+		 */
+
+		if (slot_id == DEFEA_PROD_ID_2)
+			{
+			/*
+			 * Revision 2 FDDI EISA controller found, so let's check PDQ
+			 * revision of adapter.
+			 */
+
+			status = dfx_hw_port_ctrl_req(bp,
+											PI_PCTRL_M_SUB_CMD,
+											PI_SUB_CMD_K_PDQ_REV_GET,
+											0,
+											&host_data);
+			if ((status != DFX_K_SUCCESS) || (host_data == 2))
+				{
+				/*
+				 * Either we couldn't determine the PDQ revision, or
+				 * we determined that it is at revision D.  In either case,
+				 * we need to implement the workaround.
+				 */
+
+				/* Ensure that the burst size is set to 8 longwords or less */
+
+				switch (bp->burst_size)
+					{
+					case PI_PDATA_B_DMA_BURST_SIZE_32:
+					case PI_PDATA_B_DMA_BURST_SIZE_16:
+						bp->burst_size = PI_PDATA_B_DMA_BURST_SIZE_8;
+						break;
+
+					default:
+						break;
+					}
+
+				/* Ensure that full-duplex mode is not enabled */
+
+				bp->full_duplex_enb = PI_SNMP_K_FALSE;
+				}
+			}
+		}
+	}
+
+
+/*
+ * ===================
+ * = dfx_driver_init =
+ * ===================
+ *   
+ * Overview:
+ *   Initializes remaining adapter board structure information
+ *   and makes sure adapter is in a safe state prior to dfx_open().
+ *  
+ * Returns:
+ *   Condition code
+ *       
+ * Arguments:
+ *   dev - pointer to device information
+ *   print_name - printable device name
+ *
+ * Functional Description:
+ *   This function allocates additional resources such as the host memory
+ *   blocks needed by the adapter (eg. descriptor and consumer blocks).
+ *	 Remaining bus initialization steps are also completed.  The adapter
+ *   is also reset so that it is in the DMA_UNAVAILABLE state.  The OS
+ *   must call dfx_open() to open the adapter and bring it on-line.
+ *
+ * Return Codes:
+ *   DFX_K_SUCCESS	- initialization succeeded
+ *   DFX_K_FAILURE	- initialization failed - could not allocate memory
+ *						or read adapter MAC address
+ *
+ * Assumptions:
+ *   Memory allocated from pci_alloc_consistent() call is physically
+ *   contiguous, locked memory.
+ *
+ * Side Effects:
+ *   Adapter is reset and should be in DMA_UNAVAILABLE state before
+ *   returning from this routine.
+ */
+
+static int __devinit dfx_driver_init(struct net_device *dev,
+				     const char *print_name)
+{
+	DFX_board_t *bp = dev->priv;
+	int			alloc_size;			/* total buffer size needed */
+	char		*top_v, *curr_v;	/* virtual addrs into memory block */
+	dma_addr_t		top_p, curr_p;		/* physical addrs into memory block */
+	u32			data;				/* host data register value */
+
+	DBG_printk("In dfx_driver_init...\n");
+
+	/* Initialize bus-specific hardware registers */
+
+	dfx_bus_init(dev);
+
+	/*
+	 * Initialize default values for configurable parameters
+	 *
+	 * Note: All of these parameters are ones that a user may
+	 *       want to customize.  It'd be nice to break these
+	 *		 out into Space.c or someplace else that's more
+	 *		 accessible/understandable than this file.
+	 */
+
+	bp->full_duplex_enb		= PI_SNMP_K_FALSE;
+	bp->req_ttrt			= 8 * 12500;		/* 8ms in 80 nanosec units */
+	bp->burst_size			= PI_PDATA_B_DMA_BURST_SIZE_DEF;
+	bp->rcv_bufs_to_post	= RCV_BUFS_DEF;
+
+	/*
+	 * Ensure that HW configuration is OK
+	 *
+	 * Note: Depending on the hardware revision, we may need to modify
+	 *       some of the configurable parameters to workaround hardware
+	 *       limitations.  We'll perform this configuration check AFTER
+	 *       setting the parameters to their default values.
+	 */
+
+	dfx_bus_config_check(bp);
+
+	/* Disable PDQ interrupts first */
+
+	dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
+
+	/* Place adapter in DMA_UNAVAILABLE state by resetting adapter */
+
+	(void) dfx_hw_dma_uninit(bp, PI_PDATA_A_RESET_M_SKIP_ST);
+
+	/*  Read the factory MAC address from the adapter then save it */
+
+	if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_MLA, PI_PDATA_A_MLA_K_LO, 0,
+				 &data) != DFX_K_SUCCESS) {
+		printk("%s: Could not read adapter factory MAC address!\n",
+		       print_name);
+		return(DFX_K_FAILURE);
+	}
+	memcpy(&bp->factory_mac_addr[0], &data, sizeof(u32));
+
+	if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_MLA, PI_PDATA_A_MLA_K_HI, 0,
+				 &data) != DFX_K_SUCCESS) {
+		printk("%s: Could not read adapter factory MAC address!\n",
+		       print_name);
+		return(DFX_K_FAILURE);
+	}
+	memcpy(&bp->factory_mac_addr[4], &data, sizeof(u16));
+
+	/*
+	 * Set current address to factory address
+	 *
+	 * Note: Node address override support is handled through
+	 *       dfx_ctl_set_mac_address.
+	 */
+
+	memcpy(dev->dev_addr, bp->factory_mac_addr, FDDI_K_ALEN);
+	if (bp->bus_type == DFX_BUS_TYPE_EISA)
+		printk("%s: DEFEA at I/O addr = 0x%lX, IRQ = %d, "
+		       "Hardware addr = %02X-%02X-%02X-%02X-%02X-%02X\n",
+		       print_name, dev->base_addr, dev->irq,
+		       dev->dev_addr[0], dev->dev_addr[1],
+		       dev->dev_addr[2], dev->dev_addr[3],
+		       dev->dev_addr[4], dev->dev_addr[5]);
+	else
+		printk("%s: DEFPA at I/O addr = 0x%lX, IRQ = %d, "
+		       "Hardware addr = %02X-%02X-%02X-%02X-%02X-%02X\n",
+		       print_name, dev->base_addr, dev->irq,
+		       dev->dev_addr[0], dev->dev_addr[1],
+		       dev->dev_addr[2], dev->dev_addr[3],
+		       dev->dev_addr[4], dev->dev_addr[5]);
+
+	/*
+	 * Get memory for descriptor block, consumer block, and other buffers
+	 * that need to be DMA read or written to by the adapter.
+	 */
+
+	alloc_size = sizeof(PI_DESCR_BLOCK) +
+					PI_CMD_REQ_K_SIZE_MAX +
+					PI_CMD_RSP_K_SIZE_MAX +
+#ifndef DYNAMIC_BUFFERS
+					(bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) +
+#endif
+					sizeof(PI_CONSUMER_BLOCK) +
+					(PI_ALIGN_K_DESC_BLK - 1);
+	bp->kmalloced = top_v = pci_alloc_consistent(bp->pci_dev, alloc_size,
+						     &bp->kmalloced_dma);
+	if (top_v == NULL) {
+		printk("%s: Could not allocate memory for host buffers "
+		       "and structures!\n", print_name);
+		return(DFX_K_FAILURE);
+	}
+	memset(top_v, 0, alloc_size);	/* zero out memory before continuing */
+	top_p = bp->kmalloced_dma;	/* get physical address of buffer */
+
+	/*
+	 *  To guarantee the 8K alignment required for the descriptor block, 8K - 1
+	 *  plus the amount of memory needed was allocated.  The physical address
+	 *	is now 8K aligned.  By carving up the memory in a specific order,
+	 *  we'll guarantee the alignment requirements for all other structures.
+	 *
+	 *  Note: If the assumptions change regarding the non-paged, non-cached,
+	 *		  physically contiguous nature of the memory block or the address
+	 *		  alignments, then we'll need to implement a different algorithm
+	 *		  for allocating the needed memory.
+	 */
+
+	curr_p = ALIGN(top_p, PI_ALIGN_K_DESC_BLK);
+	curr_v = top_v + (curr_p - top_p);
+
+	/* Reserve space for descriptor block */
+
+	bp->descr_block_virt = (PI_DESCR_BLOCK *) curr_v;
+	bp->descr_block_phys = curr_p;
+	curr_v += sizeof(PI_DESCR_BLOCK);
+	curr_p += sizeof(PI_DESCR_BLOCK);
+
+	/* Reserve space for command request buffer */
+
+	bp->cmd_req_virt = (PI_DMA_CMD_REQ *) curr_v;
+	bp->cmd_req_phys = curr_p;
+	curr_v += PI_CMD_REQ_K_SIZE_MAX;
+	curr_p += PI_CMD_REQ_K_SIZE_MAX;
+
+	/* Reserve space for command response buffer */
+
+	bp->cmd_rsp_virt = (PI_DMA_CMD_RSP *) curr_v;
+	bp->cmd_rsp_phys = curr_p;
+	curr_v += PI_CMD_RSP_K_SIZE_MAX;
+	curr_p += PI_CMD_RSP_K_SIZE_MAX;
+
+	/* Reserve space for the LLC host receive queue buffers */
+
+	bp->rcv_block_virt = curr_v;
+	bp->rcv_block_phys = curr_p;
+
+#ifndef DYNAMIC_BUFFERS
+	curr_v += (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX);
+	curr_p += (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX);
+#endif
+
+	/* Reserve space for the consumer block */
+
+	bp->cons_block_virt = (PI_CONSUMER_BLOCK *) curr_v;
+	bp->cons_block_phys = curr_p;
+
+	/* Display virtual and physical addresses if debug driver */
+
+	DBG_printk("%s: Descriptor block virt = %0lX, phys = %0X\n",
+		   print_name,
+		   (long)bp->descr_block_virt, bp->descr_block_phys);
+	DBG_printk("%s: Command Request buffer virt = %0lX, phys = %0X\n",
+		   print_name, (long)bp->cmd_req_virt, bp->cmd_req_phys);
+	DBG_printk("%s: Command Response buffer virt = %0lX, phys = %0X\n",
+		   print_name, (long)bp->cmd_rsp_virt, bp->cmd_rsp_phys);
+	DBG_printk("%s: Receive buffer block virt = %0lX, phys = %0X\n",
+		   print_name, (long)bp->rcv_block_virt, bp->rcv_block_phys);
+	DBG_printk("%s: Consumer block virt = %0lX, phys = %0X\n",
+		   print_name, (long)bp->cons_block_virt, bp->cons_block_phys);
+
+	return(DFX_K_SUCCESS);
+}
+
+
+/*
+ * =================
+ * = dfx_adap_init =
+ * =================
+ *   
+ * Overview:
+ *   Brings the adapter to the link avail/link unavailable state.
+ *  
+ * Returns:
+ *   Condition code
+ *       
+ * Arguments:
+ *   bp - pointer to board information
+ *   get_buffers - non-zero if buffers to be allocated
+ *
+ * Functional Description:
+ *   Issues the low-level firmware/hardware calls necessary to bring
+ *   the adapter up, or to properly reset and restore adapter during
+ *   run-time.
+ *
+ * Return Codes:
+ *   DFX_K_SUCCESS - Adapter brought up successfully
+ *   DFX_K_FAILURE - Adapter initialization failed
+ *
+ * Assumptions:
+ *   bp->reset_type should be set to a valid reset type value before
+ *   calling this routine.
+ *
+ * Side Effects:
+ *   Adapter should be in LINK_AVAILABLE or LINK_UNAVAILABLE state
+ *   upon a successful return of this routine.
+ */
+
+static int dfx_adap_init(DFX_board_t *bp, int get_buffers)
+	{
+	DBG_printk("In dfx_adap_init...\n");
+
+	/* Disable PDQ interrupts first */
+
+	dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
+
+	/* Place adapter in DMA_UNAVAILABLE state by resetting adapter */
+
+	if (dfx_hw_dma_uninit(bp, bp->reset_type) != DFX_K_SUCCESS)
+		{
+		printk("%s: Could not uninitialize/reset adapter!\n", bp->dev->name);
+		return(DFX_K_FAILURE);
+		}
+
+	/*
+	 * When the PDQ is reset, some false Type 0 interrupts may be pending,
+	 * so we'll acknowledge all Type 0 interrupts now before continuing.
+	 */
+
+	dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_0_STATUS, PI_HOST_INT_K_ACK_ALL_TYPE_0);
+
+	/*
+	 * Clear Type 1 and Type 2 registers before going to DMA_AVAILABLE state
+	 *
+	 * Note: We only need to clear host copies of these regis