bnx2x: Add Warpcore support for 578xx

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>

1 files changed, 1626 insertions, 186 deletions

diff --git a/drivers/net/bnx2x/bnx2x_link.c b/drivers/net/bnx2x/bnx2x_link.c
index 873463966a0..b777d2c9633 100644
--- a/drivers/net/bnx2x/bnx2x_link.c
+++ b/drivers/net/bnx2x/bnx2x_link.c
@@ -37,6 +37,13 @@
 #define ETH_MAX_JUMBO_PACKET_SIZE	9600
 #define MDIO_ACCESS_TIMEOUT		1000
 #define BMAC_CONTROL_RX_ENABLE		2
+#define WC_LANE_MAX			4
+#define I2C_SWITCH_WIDTH		2
+#define I2C_BSC0			0
+#define I2C_BSC1			1
+#define I2C_WA_RETRY_CNT		3
+#define MCPR_IMC_COMMAND_READ_OP	1
+#define MCPR_IMC_COMMAND_WRITE_OP	2
 
 /***********************************************************/
 /*			Shortcut definitions		   */
@@ -108,7 +115,10 @@
 #define GP_STATUS_1G_KX MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_1G_KX
 #define GP_STATUS_10G_KX4 \
 			MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KX4
-
+#define	GP_STATUS_10G_KR MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_KR
+#define	GP_STATUS_10G_XFI   MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_XFI
+#define	GP_STATUS_20G_DXGXS MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_20G_DXGXS
+#define	GP_STATUS_10G_SFI   MDIO_GP_STATUS_TOP_AN_STATUS1_ACTUAL_SPEED_10G_SFI
 #define LINK_10THD		LINK_STATUS_SPEED_AND_DUPLEX_10THD
 #define LINK_10TFD		LINK_STATUS_SPEED_AND_DUPLEX_10TFD
 #define LINK_100TXHD		LINK_STATUS_SPEED_AND_DUPLEX_100TXHD
@@ -122,11 +132,8 @@
 #define LINK_2500XFD		LINK_STATUS_SPEED_AND_DUPLEX_2500XFD
 #define LINK_10GTFD		LINK_STATUS_SPEED_AND_DUPLEX_10GTFD
 #define LINK_10GXFD		LINK_STATUS_SPEED_AND_DUPLEX_10GXFD
-
-#define PHY_XGXS_FLAG			0x1
-#define PHY_SGMII_FLAG			0x2
-#define PHY_SERDES_FLAG			0x4
-
+#define LINK_20GTFD		LINK_STATUS_SPEED_AND_DUPLEX_20GTFD
+#define LINK_20GXFD		LINK_STATUS_SPEED_AND_DUPLEX_20GXFD
 /* */
 #define SFP_EEPROM_CON_TYPE_ADDR		0x2
 	#define SFP_EEPROM_CON_TYPE_VAL_LC	0x7
@@ -247,6 +254,7 @@
 #define ETS_E3B0_PBF_MIN_W_VAL				(10000)
 
 #define MAX_PACKET_SIZE					(9700)
+#define WC_UC_TIMEOUT					100
 
 /**********************************************************/
 /*                     INTERFACE                          */
@@ -283,6 +291,47 @@ static u32 bnx2x_bits_dis(struct bnx2x *bp, u32 reg, u32 bits)
 }
 
 /******************************************************************/
+/*			EPIO/GPIO section			  */
+/******************************************************************/
+static void bnx2x_set_epio(struct bnx2x *bp, u32 epio_pin, u32 en)
+{
+	u32 epio_mask, gp_output, gp_oenable;
+
+	/* Sanity check */
+	if (epio_pin > 31) {
+		DP(NETIF_MSG_LINK, "Invalid EPIO pin %d to set\n", epio_pin);
+		return;
+	}
+	DP(NETIF_MSG_LINK, "Setting EPIO pin %d to %d\n", epio_pin, en);
+	epio_mask = 1 << epio_pin;
+	/* Set this EPIO to output */
+	gp_output = REG_RD(bp, MCP_REG_MCPR_GP_OUTPUTS);
+	if (en)
+		gp_output |= epio_mask;
+	else
+		gp_output &= ~epio_mask;
+
+	REG_WR(bp, MCP_REG_MCPR_GP_OUTPUTS, gp_output);
+
+	/* Set the value for this EPIO */
+	gp_oenable = REG_RD(bp, MCP_REG_MCPR_GP_OENABLE);
+	REG_WR(bp, MCP_REG_MCPR_GP_OENABLE, gp_oenable | epio_mask);
+}
+
+static void bnx2x_set_cfg_pin(struct bnx2x *bp, u32 pin_cfg, u32 val)
+{
+	if (pin_cfg == PIN_CFG_NA)
+		return;
+	if (pin_cfg >= PIN_CFG_EPIO0) {
+		bnx2x_set_epio(bp, pin_cfg - PIN_CFG_EPIO0, val);
+	} else {
+		u8 gpio_num = (pin_cfg - PIN_CFG_GPIO0_P0) & 0x3;
+		u8 gpio_port = (pin_cfg - PIN_CFG_GPIO0_P0) >> 2;
+		bnx2x_set_gpio(bp, gpio_num, (u8)val, gpio_port);
+	}
+}
+
+/******************************************************************/
 /*				ETS section			  */
 /******************************************************************/
 void bnx2x_ets_disabled(struct link_params *params)
@@ -607,7 +656,10 @@ static void bnx2x_set_mdio_clk(struct bnx2x *bp, u32 chip_id, u8 port)
 	mode = REG_RD(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE);
 	mode &= ~(EMAC_MDIO_MODE_AUTO_POLL |
 		  EMAC_MDIO_MODE_CLOCK_CNT);
-	mode |= (49L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT);
+	if (USES_WARPCORE(bp))
+		mode |= (74L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT);
+	else
+		mode |= (49L << EMAC_MDIO_MODE_CLOCK_CNT_BITSHIFT);
 
 	mode |= (EMAC_MDIO_MODE_CLAUSE_45);
 	REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_MODE, mode);
@@ -729,7 +781,7 @@ static void bnx2x_umac_enable(struct link_params *params,
 	/* Enable RX and TX */
 	val &= ~UMAC_COMMAND_CONFIG_REG_PAD_EN;
 	val |= UMAC_COMMAND_CONFIG_REG_TX_ENA |
-	       UMAC_COMMAND_CONFIG_REG_RX_ENA;
+		UMAC_COMMAND_CONFIG_REG_RX_ENA;
 	REG_WR(bp, umac_base + UMAC_REG_COMMAND_CONFIG, val);
 	udelay(50);
 
@@ -1649,7 +1701,7 @@ int bnx2x_update_pfc(struct link_params *params,
 	else {
 		val = REG_RD(bp, MISC_REG_RESET_REG_2);
 		if ((val &
-		    (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << params->port))
+		     (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << params->port))
 		    == 0) {
 			DP(NETIF_MSG_LINK, "About to update PFC in EMAC\n");
 			bnx2x_emac_enable(params, vars, 0);
@@ -1940,18 +1992,6 @@ static int bnx2x_pbf_update(struct link_params *params, u32 flow_ctrl,
 		case SPEED_10000:
 			init_crd = thresh + 553 - 22;
 			break;
-
-		case SPEED_12000:
-			init_crd = thresh + 664 - 22;
-			break;
-
-		case SPEED_13000:
-			init_crd = thresh + 742 - 22;
-			break;
-
-		case SPEED_16000:
-			init_crd = thresh + 778 - 22;
-			break;
 		default:
 			DP(NETIF_MSG_LINK, "Invalid line_speed 0x%x\n",
 				  line_speed);
@@ -2073,6 +2113,14 @@ static int bnx2x_cl45_read(struct bnx2x *bp, struct bnx2x_phy *phy,
 			rc = -EFAULT;
 		}
 	}
+	/* Work around for E3 A0 */
+	if (phy->flags & FLAGS_MDC_MDIO_WA) {
+		phy->flags ^= FLAGS_DUMMY_READ;
+		if (phy->flags & FLAGS_DUMMY_READ) {
+			u16 temp_val;
+			bnx2x_cl45_read(bp, phy, devad, 0xf, &temp_val);
+		}
+	}
 
 	return rc;
 }
@@ -2128,11 +2176,149 @@ static int bnx2x_cl45_write(struct bnx2x *bp, struct bnx2x_phy *phy,
 			rc = -EFAULT;
 		}
 	}
+	/* Work around for E3 A0 */
+	if (phy->flags & FLAGS_MDC_MDIO_WA) {
+		phy->flags ^= FLAGS_DUMMY_READ;
+		if (phy->flags & FLAGS_DUMMY_READ) {
+			u16 temp_val;
+			bnx2x_cl45_read(bp, phy, devad, 0xf, &temp_val);
+		}
+	}
+
+	return rc;
+}
+
+
+/******************************************************************/
+/*			BSC access functions from E3	          */
+/******************************************************************/
+static void bnx2x_bsc_module_sel(struct link_params *params)
+{
+	int idx;
+	u32 board_cfg, sfp_ctrl;
+	u32 i2c_pins[I2C_SWITCH_WIDTH], i2c_val[I2C_SWITCH_WIDTH];
+	struct bnx2x *bp = params->bp;
+	u8 port = params->port;
+	/* Read I2C output PINs */
+	board_cfg = REG_RD(bp, params->shmem_base +
+			   offsetof(struct shmem_region,
+				    dev_info.shared_hw_config.board));
+	i2c_pins[I2C_BSC0] = board_cfg & SHARED_HW_CFG_E3_I2C_MUX0_MASK;
+	i2c_pins[I2C_BSC1] = (board_cfg & SHARED_HW_CFG_E3_I2C_MUX1_MASK) >>
+			SHARED_HW_CFG_E3_I2C_MUX1_SHIFT;
+
+	/* Read I2C output value */
+	sfp_ctrl = REG_RD(bp, params->shmem_base +
+			  offsetof(struct shmem_region,
+				 dev_info.port_hw_config[port].e3_cmn_pin_cfg));
+	i2c_val[I2C_BSC0] = (sfp_ctrl & PORT_HW_CFG_E3_I2C_MUX0_MASK) > 0;
+	i2c_val[I2C_BSC1] = (sfp_ctrl & PORT_HW_CFG_E3_I2C_MUX1_MASK) > 0;
+	DP(NETIF_MSG_LINK, "Setting BSC switch\n");
+	for (idx = 0; idx < I2C_SWITCH_WIDTH; idx++)
+		bnx2x_set_cfg_pin(bp, i2c_pins[idx], i2c_val[idx]);
+}
+
+static int bnx2x_bsc_read(struct link_params *params,
+			  struct bnx2x_phy *phy,
+			  u8 sl_devid,
+			  u16 sl_addr,
+			  u8 lc_addr,
+			  u8 xfer_cnt,
+			  u32 *data_array)
+{
+	u32 val, i;
+	int rc = 0;
+	struct bnx2x *bp = params->bp;
+
+	if ((sl_devid != 0xa0) && (sl_devid != 0xa2)) {
+		DP(NETIF_MSG_LINK, "invalid sl_devid 0x%x\n", sl_devid);
+		return -EINVAL;
+	}
+
+	if (xfer_cnt > 16) {
+		DP(NETIF_MSG_LINK, "invalid xfer_cnt %d. Max is 16 bytes\n",
+					xfer_cnt);
+		return -EINVAL;
+	}
+	bnx2x_bsc_module_sel(params);
+
+	xfer_cnt = 16 - lc_addr;
+
+	/* enable the engine */
+	val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
+	val |= MCPR_IMC_COMMAND_ENABLE;
+	REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val);
+
+	/* program slave device ID */
+	val = (sl_devid << 16) | sl_addr;
+	REG_WR(bp, MCP_REG_MCPR_IMC_SLAVE_CONTROL, val);
+
+	/* start xfer with 0 byte to update the address pointer ???*/
+	val = (MCPR_IMC_COMMAND_ENABLE) |
+	      (MCPR_IMC_COMMAND_WRITE_OP <<
+		MCPR_IMC_COMMAND_OPERATION_BITSHIFT) |
+		(lc_addr << MCPR_IMC_COMMAND_TRANSFER_ADDRESS_BITSHIFT) | (0);
+	REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val);
+
+	/* poll for completion */
+	i = 0;
+	val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
+	while (((val >> MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT) & 0x3) != 1) {
+		udelay(10);
+		val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
+		if (i++ > 1000) {
+			DP(NETIF_MSG_LINK, "wr 0 byte timed out after %d try\n",
+								i);
+			rc = -EFAULT;
+			break;
+		}
+	}
+	if (rc == -EFAULT)
+		return rc;
 
+	/* start xfer with read op */
+	val = (MCPR_IMC_COMMAND_ENABLE) |
+		(MCPR_IMC_COMMAND_READ_OP <<
+		MCPR_IMC_COMMAND_OPERATION_BITSHIFT) |
+		(lc_addr << MCPR_IMC_COMMAND_TRANSFER_ADDRESS_BITSHIFT) |
+		  (xfer_cnt);
+	REG_WR(bp, MCP_REG_MCPR_IMC_COMMAND, val);
+
+	/* poll for completion */
+	i = 0;
+	val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
+	while (((val >> MCPR_IMC_COMMAND_IMC_STATUS_BITSHIFT) & 0x3) != 1) {
+		udelay(10);
+		val = REG_RD(bp, MCP_REG_MCPR_IMC_COMMAND);
+		if (i++ > 1000) {
+			DP(NETIF_MSG_LINK, "rd op timed out after %d try\n", i);
+			rc = -EFAULT;
+			break;
+		}
+	}
+	if (rc == -EFAULT)
+		return rc;
 
+	for (i = (lc_addr >> 2); i < 4; i++) {
+		data_array[i] = REG_RD(bp, (MCP_REG_MCPR_IMC_DATAREG0 + i*4));
+#ifdef __BIG_ENDIAN
+		data_array[i] = ((data_array[i] & 0x000000ff) << 24) |
+				((data_array[i] & 0x0000ff00) << 8) |
+				((data_array[i] & 0x00ff0000) >> 8) |
+				((data_array[i] & 0xff000000) >> 24);
+#endif
+	}
 	return rc;
 }
 
+static void bnx2x_cl45_read_or_write(struct bnx2x *bp, struct bnx2x_phy *phy,
+				     u8 devad, u16 reg, u16 or_val)
+{
+	u16 val;
+	bnx2x_cl45_read(bp, phy, devad, reg, &val);
+	bnx2x_cl45_write(bp, phy, devad, reg, val | or_val);
+}
+
 int bnx2x_phy_read(struct link_params *params, u8 phy_addr,
 		   u8 devad, u16 reg, u16 *ret_val)
 {
@@ -2168,6 +2354,59 @@ int bnx2x_phy_write(struct link_params *params, u8 phy_addr,
 	}
 	return -EINVAL;
 }
+static u8 bnx2x_get_warpcore_lane(struct bnx2x_phy *phy,
+				  struct link_params *params)
+{
+	u8 lane = 0;
+	struct bnx2x *bp = params->bp;
+	u32 path_swap, path_swap_ovr;
+	u8 path, port;
+
+	path = BP_PATH(bp);
+	port = params->port;
+
+	if (bnx2x_is_4_port_mode(bp)) {
+		u32 port_swap, port_swap_ovr;
+
+		/*figure out path swap value */
+		path_swap_ovr = REG_RD(bp, MISC_REG_FOUR_PORT_PATH_SWAP_OVWR);
+		if (path_swap_ovr & 0x1)
+			path_swap = (path_swap_ovr & 0x2);
+		else
+			path_swap = REG_RD(bp, MISC_REG_FOUR_PORT_PATH_SWAP);
+
+		if (path_swap)
+			path = path ^ 1;
+
+		/*figure out port swap value */
+		port_swap_ovr = REG_RD(bp, MISC_REG_FOUR_PORT_PORT_SWAP_OVWR);
+		if (port_swap_ovr & 0x1)
+			port_swap = (port_swap_ovr & 0x2);
+		else
+			port_swap = REG_RD(bp, MISC_REG_FOUR_PORT_PORT_SWAP);
+
+		if (port_swap)
+			port = port ^ 1;
+
+		lane = (port<<1) + path;
+	} else { /* two port mode - no port swap */
+
+		/*figure out path swap value */
+		path_swap_ovr =
+			REG_RD(bp, MISC_REG_TWO_PORT_PATH_SWAP_OVWR);
+		if (path_swap_ovr & 0x1) {
+			path_swap = (path_swap_ovr & 0x2);
+		} else {
+			path_swap =
+				REG_RD(bp, MISC_REG_TWO_PORT_PATH_SWAP);
+		}
+		if (path_swap)
+			path = path ^ 1;
+
+		lane = path << 1 ;
+	}
+	return lane;
+}
 
 static void bnx2x_set_aer_mmd(struct link_params *params,
 			      struct bnx2x_phy *phy)
@@ -2182,7 +2421,18 @@ static void bnx2x_set_aer_mmd(struct link_params *params,
 	offset = (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) ?
 		(phy->addr + ser_lane) : 0;
 
-	if (CHIP_IS_E2(bp))
+	if (USES_WARPCORE(bp)) {
+		aer_val = bnx2x_get_warpcore_lane(phy, params);
+		/*
+		 * In Dual-lane mode, two lanes are joined together,
+		 * so in order to configure them, the AER broadcast method is
+		 * used here.
+		 * 0x200 is the broadcast address for lanes 0,1
+		 * 0x201 is the broadcast address for lanes 2,3
+		 */
+		if (phy->flags & FLAGS_WC_DUAL_MODE)
+			aer_val = (aer_val >> 1) | 0x200;
+	} else if (CHIP_IS_E2(bp))
 		aer_val = 0x3800 + offset - 1;
 	else
 		aer_val = 0x3800 + offset;
@@ -2415,6 +2665,778 @@ static u8 bnx2x_ext_phy_resolve_fc(struct bnx2x_phy *phy,
 	}
 	return ret;
 }
+/******************************************************************/
+/*			Warpcore section			  */
+/******************************************************************/
+/* The init_internal_warpcore should mirror the xgxs,
+ * i.e. reset the lane (if needed), set aer for the
+ * init configuration, and set/clear SGMII flag. Internal
+ * phy init is done purely in phy_init stage.
+ */
+static void bnx2x_warpcore_enable_AN_KR(struct bnx2x_phy *phy,
+					struct link_params *params,
+					struct link_vars *vars) {
+	u16 val16 = 0, lane;
+	struct bnx2x *bp = params->bp;
+	DP(NETIF_MSG_LINK, "Enable Auto Negotiation for KR\n");
+	/* Check adding advertisement for 1G KX */
+	if (((vars->line_speed == SPEED_AUTO_NEG) &&
+	     (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_1G)) ||
+	    (vars->line_speed == SPEED_1000)) {
+		u16 sd_digital;
+		val16 |= (1<<5);
+
+		/* Enable CL37 1G Parallel Detect */
+		bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, &sd_digital);
+		bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2,
+				 (sd_digital | 0x1));
+
+		DP(NETIF_MSG_LINK, "Advertize 1G\n");
+	}
+	if (((vars->line_speed == SPEED_AUTO_NEG) &&
+	     (phy->speed_cap_mask & PORT_HW_CFG_SPEED_CAPABILITY_D0_10G)) ||
+	    (vars->line_speed ==  SPEED_10000)) {
+		/* Check adding advertisement for 10G KR */
+		val16 |= (1<<7);
+		/* Enable 10G Parallel Detect */
+		bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
+				MDIO_WC_REG_PAR_DET_10G_CTRL, 1);
+
+		DP(NETIF_MSG_LINK, "Advertize 10G\n");
+	}
+
+	/* Set Transmit PMD settings */
+	lane = bnx2x_get_warpcore_lane(phy, params);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+		      MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane,
+		     ((0x02 << MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET) |
+		      (0x06 << MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET) |
+		      (0x09 << MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET)));
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_CL72_USERB0_CL72_OS_DEF_CTRL,
+			 0x03f0);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_CL72_USERB0_CL72_2P5_DEF_CTRL,
+			 0x03f0);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL,
+			 0x383f);
+
+	/* Advertised speeds */
+	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
+			 MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT1, val16);
+
+	/* Advertise pause */
+	bnx2x_ext_phy_set_pause(params, phy, vars);
+
+	/* Enable Autoneg */
+	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
+			 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x1000);
+
+	/* Over 1G - AN local device user page 1 */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_DIGITAL3_UP1, 0x1f);
+
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_DIGITAL5_MISC7, &val16);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_DIGITAL5_MISC7, val16 | 0x100);
+}
+
+static void bnx2x_warpcore_set_10G_KR(struct bnx2x_phy *phy,
+				      struct link_params *params,
+				      struct link_vars *vars)
+{
+	struct bnx2x *bp = params->bp;
+	u16 val;
+
+	/* Disable Autoneg */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 0x7);
+
+	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
+			 MDIO_WC_REG_PAR_DET_10G_CTRL, 0);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL, 0x3f00);
+
+	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
+			 MDIO_WC_REG_AN_IEEE1BLK_AN_ADVERTISEMENT1, 0);
+
+	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD,
+			 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x0);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_DIGITAL3_UP1, 0x1);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_DIGITAL5_MISC7, 0xa);
+
+	/* Disable CL36 PCS Tx */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_XGXSBLK1_LANECTRL0, 0x0);
+
+	/* Double Wide Single Data Rate @ pll rate */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_XGXSBLK1_LANECTRL1, 0xFFFF);
+
+	/* Leave cl72 training enable, needed for KR */
+	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD,
+		MDIO_WC_REG_PMD_IEEE9BLK_TENGBASE_KR_PMD_CONTROL_REGISTER_150,
+		0x2);
+
+	/* Leave CL72 enabled */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL,
+			 &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_CL72_USERB0_CL72_MISC1_CONTROL,
+			 val | 0x3800);
+
+	/* Set speed via PMA/PMD register */
+	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD,
+			 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x2040);
+
+	bnx2x_cl45_write(bp, phy, MDIO_PMA_DEVAD,
+			 MDIO_WC_REG_IEEE0BLK_AUTONEGNP, 0xB);
+
+	/*Enable encoded forced speed */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_MISC2, 0x30);
+
+	/* Turn TX scramble payload only the 64/66 scrambler */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_TX66_CONTROL, 0x9);
+
+	/* Turn RX scramble payload only the 64/66 scrambler */
+	bnx2x_cl45_read_or_write(bp, phy, MDIO_WC_DEVAD,
+				 MDIO_WC_REG_RX66_CONTROL, 0xF9);
+
+	/* set and clear loopback to cause a reset to 64/66 decoder */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x4000);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x0);
+
+}
+
+static void bnx2x_warpcore_set_10G_XFI(struct bnx2x_phy *phy,
+				       struct link_params *params,
+				       u8 is_xfi)
+{
+	struct bnx2x *bp = params->bp;
+	u16 misc1_val, tap_val, tx_driver_val, lane, val;
+	/* Hold rxSeqStart */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0, (val | 0x8000));
+
+	/* Hold tx_fifo_reset */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, (val | 0x1));
+
+	/* Disable CL73 AN */
+	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0);
+
+	/* Disable 100FX Enable and Auto-Detect */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_FX100_CTRL1, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_FX100_CTRL1, (val & 0xFFFA));
+
+	/* Disable 100FX Idle detect */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_FX100_CTRL3, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_FX100_CTRL3, (val | 0x0080));
+
+	/* Set Block address to Remote PHY & Clear forced_speed[5] */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_DIGITAL4_MISC3, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_DIGITAL4_MISC3, (val & 0xFF7F));
+
+	/* Turn off auto-detect & fiber mode */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1,
+			 (val & 0xFFEE));
+
+	/* Set filter_force_link, disable_false_link and parallel_detect */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2,
+			 ((val | 0x0006) & 0xFFFE));
+
+	/* Set XFI / SFI */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_MISC1, &misc1_val);
+
+	misc1_val &= ~(0x1f);
+
+	if (is_xfi) {
+		misc1_val |= 0x5;
+		tap_val = ((0x08 << MDIO_WC_REG_TX_FIR_TAP_POST_TAP_OFFSET) |
+			   (0x37 << MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_OFFSET) |
+			   (0x00 << MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_OFFSET));
+		tx_driver_val =
+		      ((0x00 << MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET) |
+		       (0x02 << MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET) |
+		       (0x03 << MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET));
+
+	} else {
+		misc1_val |= 0x9;
+		tap_val = ((0x12 << MDIO_WC_REG_TX_FIR_TAP_POST_TAP_OFFSET) |
+			   (0x2d << MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_OFFSET) |
+			   (0x00 << MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_OFFSET));
+		tx_driver_val =
+		      ((0x02 << MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET) |
+		       (0x02 << MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET) |
+		       (0x02 << MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET));
+	}
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_MISC1, misc1_val);
+
+	/* Set Transmit PMD settings */
+	lane = bnx2x_get_warpcore_lane(phy, params);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_TX_FIR_TAP,
+			 tap_val | MDIO_WC_REG_TX_FIR_TAP_ENABLE);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane,
+			 tx_driver_val);
+
+	/* Enable fiber mode, enable and invert sig_det */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, val | 0xd);
+
+	/* Set Block address to Remote PHY & Set forced_speed[5], 40bit mode */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_DIGITAL4_MISC3, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_DIGITAL4_MISC3, val | 0x8080);
+
+	/* 10G XFI Full Duplex */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x100);
+
+	/* Release tx_fifo_reset */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, val & 0xFFFE);
+
+	/* Release rxSeqStart */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0, &val);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_DSC2B0_DSC_MISC_CTRL0, (val & 0x7FFF));
+}
+
+static void bnx2x_warpcore_set_20G_KR2(struct bnx2x *bp,
+				       struct bnx2x_phy *phy)
+{
+	DP(NETIF_MSG_LINK, "KR2 still not supported !!!\n");
+}
+
+static void bnx2x_warpcore_set_20G_DXGXS(struct bnx2x *bp,
+					 struct bnx2x_phy *phy,
+					 u16 lane)
+{
+	/* Rx0 anaRxControl1G */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX0_ANARXCONTROL1G, 0x90);
+
+	/* Rx2 anaRxControl1G */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX2_ANARXCONTROL1G, 0x90);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX66_SCW0, 0xE070);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX66_SCW1, 0xC0D0);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX66_SCW2, 0xA0B0);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX66_SCW3, 0x8090);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX66_SCW0_MASK, 0xF0F0);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX66_SCW1_MASK, 0xF0F0);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX66_SCW2_MASK, 0xF0F0);
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX66_SCW3_MASK, 0xF0F0);
+
+	/* Serdes Digital Misc1 */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_MISC1, 0x6008);
+
+	/* Serdes Digital4 Misc3 */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_DIGITAL4_MISC3, 0x8088);
+
+	/* Set Transmit PMD settings */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_TX_FIR_TAP,
+			((0x12 << MDIO_WC_REG_TX_FIR_TAP_POST_TAP_OFFSET) |
+			 (0x2d << MDIO_WC_REG_TX_FIR_TAP_MAIN_TAP_OFFSET) |
+			 (0x00 << MDIO_WC_REG_TX_FIR_TAP_PRE_TAP_OFFSET) |
+			 MDIO_WC_REG_TX_FIR_TAP_ENABLE));
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+		      MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane,
+		     ((0x02 << MDIO_WC_REG_TX0_TX_DRIVER_POST2_COEFF_OFFSET) |
+		      (0x02 << MDIO_WC_REG_TX0_TX_DRIVER_IDRIVER_OFFSET) |
+		      (0x02 << MDIO_WC_REG_TX0_TX_DRIVER_IPRE_DRIVER_OFFSET)));
+}
+
+static void bnx2x_warpcore_set_sgmii_speed(struct bnx2x_phy *phy,
+					   struct link_params *params,
+					   u8 fiber_mode)
+{
+	struct bnx2x *bp = params->bp;
+	u16 val16, digctrl_kx1, digctrl_kx2;
+	u8 lane;
+
+	lane = bnx2x_get_warpcore_lane(phy, params);
+
+	/* Clear XFI clock comp in non-10G single lane mode. */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_RX66_CONTROL, &val16);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX66_CONTROL, val16 & ~(3<<13));
+
+	if (phy->req_line_speed == SPEED_AUTO_NEG) {
+		/* SGMII Autoneg */
+		bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+				MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16);
+		bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+				 MDIO_WC_REG_COMBO_IEEE0_MIICTRL,
+				 val16 | 0x1000);
+		DP(NETIF_MSG_LINK, "set SGMII AUTONEG\n");
+	} else {
+		bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+				MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16);
+		val16 &= 0xcfbf;
+		switch (phy->req_line_speed) {
+		case SPEED_10:
+			break;
+		case SPEED_100:
+			val16 |= 0x2000;
+			break;
+		case SPEED_1000:
+			val16 |= 0x0040;
+			break;
+		default:
+			DP(NETIF_MSG_LINK, "Speed not supported: 0x%x"
+					   "\n", phy->req_line_speed);
+			return;
+		}
+
+		if (phy->req_duplex == DUPLEX_FULL)
+			val16 |= 0x0100;
+
+		bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+				MDIO_WC_REG_COMBO_IEEE0_MIICTRL, val16);
+
+		DP(NETIF_MSG_LINK, "set SGMII force speed %d\n",
+			       phy->req_line_speed);
+		bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+				MDIO_WC_REG_COMBO_IEEE0_MIICTRL, &val16);
+		DP(NETIF_MSG_LINK, "  (readback) %x\n", val16);
+	}
+
+	/* SGMII Slave mode and disable signal detect */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, &digctrl_kx1);
+	if (fiber_mode)
+		digctrl_kx1 = 1;
+	else
+		digctrl_kx1 &= 0xff4a;
+
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1,
+			digctrl_kx1);
+
+	/* Turn off parallel detect */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, &digctrl_kx2);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2,
+			(digctrl_kx2 & ~(1<<2)));
+
+	/* Re-enable parallel detect */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2,
+			(digctrl_kx2 | (1<<2)));
+
+	/* Enable autodet */
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1,
+			(digctrl_kx1 | 0x10));
+}
+
+static void bnx2x_warpcore_reset_lane(struct bnx2x *bp,
+				      struct bnx2x_phy *phy,
+				      u8 reset)
+{
+	u16 val;
+	/* Take lane out of reset after configuration is finished */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_DIGITAL5_MISC6, &val);
+	if (reset)
+		val |= 0xC000;
+	else
+		val &= 0x3FFF;
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_DIGITAL5_MISC6, val);
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_DIGITAL5_MISC6, &val);
+}
+
+
+	/* Clear SFI/XFI link settings registers */
+static void bnx2x_warpcore_clear_regs(struct bnx2x_phy *phy,
+				      struct link_params *params,
+				      u16 lane)
+{
+	struct bnx2x *bp = params->bp;
+	u16 val16;
+
+	/* Set XFI clock comp as default. */
+	bnx2x_cl45_read(bp, phy, MDIO_WC_DEVAD,
+			MDIO_WC_REG_RX66_CONTROL, &val16);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_RX66_CONTROL, val16 | (3<<13));
+
+	bnx2x_warpcore_reset_lane(bp, phy, 1);
+	bnx2x_cl45_write(bp, phy, MDIO_AN_DEVAD, MDIO_AN_REG_CTRL, 0);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_FX100_CTRL1, 0x014a);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_FX100_CTRL3, 0x0800);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_DIGITAL4_MISC3, 0x8008);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X1, 0x0195);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X2, 0x0007);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_CONTROL1000X3, 0x0002);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_SERDESDIGITAL_MISC1, 0x6000);
+	lane = bnx2x_get_warpcore_lane(phy, params);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_TX_FIR_TAP, 0x0000);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_TX0_TX_DRIVER + 0x10*lane, 0x0990);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_IEEE0BLK_MIICNTL, 0x2040);
+	bnx2x_cl45_write(bp, phy, MDIO_WC_DEVAD,
+			 MDIO_WC_REG_COMBO_IEEE0_MIICTRL, 0x0140);
+	bnx2x_warpcore_reset_lane(bp, phy, 0);
+}
+
+static int bnx2x_get_mod_abs_int_cfg(struct bnx2x *bp,
+						u32 chip_id,
+						u32 shmem_base, u8 port,
+						u8 *gpio_num, u8 *gpio_port)
+{
+	u32 cfg_pin;
+	*gpio_num = 0;
+	*gpio_port = 0;
+	if (CHIP_IS_E3(bp)) {
+		cfg_pin = (REG_RD(bp, shmem_base +
+				offsetof(struct shmem_region,
+				dev_info.port_hw_config[port].e3_sfp_ctrl)) &
+				PORT_HW_CFG_E3_MOD_ABS_MASK) >>
+				PORT_HW_CFG_E3_MOD_ABS_SHIFT;
+
+		/*
+		 * Should not happen. This function called upon interrupt
+		 * triggered by GPIO ( since EPIO can only generate interrupts
+		 * to MCP).
+		 * So if this function was called and none of the GPIOs was set,
+		 * it means the shit hit the fan.
+		 */
+		if ((cfg_pin < PIN_CFG_GPIO0_P0) ||
+		    (cfg_pin > PIN_CFG_GPIO3_P1)) {
+			DP(NETIF_MSG_LINK, "ERROR: Invalid cfg pin %x for "
+					   "module detect indication\n",
+				       cfg_pin);
+			return -EINVAL;
+		}
+
+		*gpio_num = (cfg_pin - PIN_CFG_GPIO0_P0) & 0x3;
+		*gpio_port = (cfg_pin - PIN_CFG_GPIO0_P0) >> 2;
+	} else {
+		*gpio_num = MISC_REGISTERS_GPIO_3;
+		*gpio_port = port;
+	}
+	DP(NETIF_MSG_LINK, "MOD_ABS int GPIO%d_P%d\n", *gpio_num, *gpio_port);
+	return 0;
+}
+
+static int bnx2x_is_sfp_module_plugged(struct bnx2x_phy *phy,
+				       struct link_params *params)
+{
+	struct bnx2x *bp = params->bp;
+	u8 gpio_num, gpio_port;
+	u32 gpio_val;
+	if (bnx2x_get_mod_abs_int_cfg(bp, params->chip_id,
+				      params->shmem_base, params->port,
+				      &gpio_num, &gpio_port) != 0)
+		return 0;
+	gpio_val = bnx2x_get_gpio(bp, gpio_num, gpio_port);
+
+	/* Call the handling function in case module is detected */
+	if (gpio_val == 0)
+		return 1;
+	else
+		return 0;
+}
+
+static void bnx2x_warpcore_config_init(struct bnx2x_phy *phy,
+				       struct link_params *params,
+				       struct link_vars *vars)
+{
+	struct bnx2x *bp = params->bp;
+	u32 serdes_net_if;
+	u8 fiber_mode;
+	u16 lane = bnx2x_get_warpcore_lane(phy, params);
+	serdes_net_if = (REG_RD(bp, params->shmem_base +
+			 offsetof(struct shmem_region, dev_info.
+				  port_hw_config[params->port].default_cfg)) &
+			 PORT_HW_CFG_NET_SERDES_IF_MASK);
+	DP(NETIF_MSG_LINK, "Begin Warpcore init, link_speed %d, "
+			   "serdes_net_if = 0x%x\n",
+		       vars->line_speed, serdes_net_if);
+	bnx2x_set_aer_mmd(params, phy);
+
+	vars->phy_flags |= PHY_XGXS_FLAG;
+	if ((serdes_net_if == PORT_HW_CFG_NET_SERDES_IF_SGMII) ||
+	    (phy->req_line_speed &&
+	     ((phy->req_line_speed == SPEED_100) ||
+	      (phy->req_line_speed == SPEED_10)))) {
+		vars->phy_flags |= PHY_SGMII_FLAG;
+		DP(NETIF_MSG_LINK, "Setting SGMII mode\n");
+		bnx2x_warpcore_clear_regs(phy, params, lane);
+		bnx2x_warpcore_set_sgmii_speed(phy, params, 0);
+	} else {
+		switch (serdes_net_if) {
+		case PORT_HW_CFG_NET_SERDES_IF_KR:
+			/* Enable KR Auto Neg */
+			if (params->loopback_mode == LOOPBACK_NONE)
+				bnx2x_warpcore_enable_AN_KR(phy, params, vars);
+			else {
+				DP(NETIF_MSG_LINK, "Setting KR 10G-Force\n");
+				bnx2x_warpcore_set_10G_KR(phy, params, vars);
+			}
+			break;
+
+		case PORT_HW_CFG_NET_SERDES_IF_XFI:
+			bnx2x_warpcore_clear_regs(phy, params, lane);
+			if (vars->line_speed == SPEED_10000) {
+				DP(NETIF_MSG_LINK, "Setting 10G XFI\n");
+				bnx2x_warpcore_set_10G_XFI(phy, params, 1);
+			} else {
+				if (SINGLE_MEDIA_DIRECT(params)) {
+					DP(NETIF_MSG_LINK, "1G Fiber\n");
+					fiber_mode = 1;
+				} else {
+					DP(NETIF_MSG_LINK, "10/100/1G SGMII\n");
+					fiber_mode = 0;
+				}
+				bnx2x_warpcore_set_sgmii_speed(phy,
+								params,
+								fiber_mode);
+			}
+
+			break;
+
+		case PORT_HW_CFG_NET_SERDES_IF_SFI:
+
+			bnx2x_warpcore_clear_regs(phy, params, lane);
+			if (vars->line_speed == SPEED_10000) {
+				DP(NETIF_MSG_LINK, "Setting 10G SFI\n");
+				bnx2x_warpcore_set_10G_XFI(phy, params, 0);
+			} else if (vars->line_speed == SPEED_1000) {
+				DP(NETIF_MSG_LINK, "Setting 1G Fiber\n");
+				bnx2x_warpcore_set_sgmii_speed(phy, params, 1);
+			}
+			/* Issue Module detection */
+			if (bnx2x_is_sfp_module_plugged(phy, params))
+				bnx2x_sfp_module_detection(phy, params);
+			break;
+
+		case PORT_HW_CFG_NET_SERDES_IF_DXGXS:
+			if (vars->line_speed != SPEED_20000) {
+				DP(NETIF_MSG_LINK, "Speed not supported yet\n");
+				return;
+			}
+			DP(NETIF_MSG_LINK, "Setting 20G DXGXS\n");
+			bnx2x_warpcore_set_20G_DXGXS(bp, phy, lane);
+			/* Issue Module detection */
+
+			bnx2x_sfp_module_detection(phy, params);
+			break;
+
+		case PORT_HW_CFG_NET_SERDES_IF_KR2:
+			if (vars->line_speed != SPEED_20000) {
+				DP(NETIF_MSG_LINK, "Speed not supported yet\n");
+				return;
+			}
+			DP(NETIF_MSG_LINK, "Setting 20G KR2\n");
+			bnx2x_warpcore_set_20G_KR2(bp, phy);
+			break;
+
+		default:
+			DP(NETIF_MSG_LINK, "Unsupported Serdes Net Interface "
+					   "0x%x\n", serdes_net_if);
+			return;
+		}
+	}
+
+	/* Take lane out of reset after configuration is finished */
+	bnx2x_warpcore_reset_lane(bp, phy, 0);
+	DP(NETIF_MSG_LINK, "Exit config init\n");
+}
+
+static void bnx2x_sfp_e3_set_transmitter(struct link_params *params,
+					 struct bnx2x_phy *phy,
+					 u8 tx_en)
+{
+	struct bnx2x *bp = params->bp;
+	u32 cfg_pin;
+	u8 port = params->port;
+
+	cfg_pin = REG_RD(bp, params->shmem_base +
+				offsetof(struct shmem_region,
+				dev_info.port_hw_config[port].e3_sfp_ctrl)) &
+				PORT_HW_CFG_TX_LASER_MASK;