Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 214 insertions, 0 deletions

diff --git a/drivers/net/8390.h b/drivers/net/8390.h
new file mode 100644
index 00000000000..599b68d8c45
--- /dev/null
+++ b/drivers/net/8390.h
@@ -0,0 +1,214 @@
+/* Generic NS8390 register definitions. */
+/* This file is part of Donald Becker's 8390 drivers, and is distributed
+   under the same license. Auto-loading of 8390.o only in v2.2 - Paul G.
+   Some of these names and comments originated from the Crynwr
+   packet drivers, which are distributed under the GPL. */
+
+#ifndef _8390_h
+#define _8390_h
+
+#include <linux/config.h>
+#include <linux/if_ether.h>
+#include <linux/ioport.h>
+#include <linux/skbuff.h>
+
+#define TX_PAGES 12	/* Two Tx slots */
+
+#define ETHER_ADDR_LEN 6
+
+/* The 8390 specific per-packet-header format. */
+struct e8390_pkt_hdr {
+  unsigned char status; /* status */
+  unsigned char next;   /* pointer to next packet. */
+  unsigned short count; /* header + packet length in bytes */
+};
+
+#ifdef notdef
+extern int ei_debug;
+#else
+#define ei_debug 1
+#endif
+
+#ifdef CONFIG_NET_POLL_CONTROLLER
+extern void ei_poll(struct net_device *dev);
+#endif
+
+extern void NS8390_init(struct net_device *dev, int startp);
+extern int ei_open(struct net_device *dev);
+extern int ei_close(struct net_device *dev);
+extern irqreturn_t ei_interrupt(int irq, void *dev_id, struct pt_regs *regs);
+extern struct net_device *__alloc_ei_netdev(int size);
+static inline struct net_device *alloc_ei_netdev(void)
+{
+	return __alloc_ei_netdev(0);
+}
+
+/* You have one of these per-board */
+struct ei_device {
+	const char *name;
+	void (*reset_8390)(struct net_device *);
+	void (*get_8390_hdr)(struct net_device *, struct e8390_pkt_hdr *, int);
+	void (*block_output)(struct net_device *, int, const unsigned char *, int);
+	void (*block_input)(struct net_device *, int, struct sk_buff *, int);
+	unsigned long rmem_start;
+	unsigned long rmem_end;
+	void __iomem *mem;
+	unsigned char mcfilter[8];
+	unsigned open:1;
+	unsigned word16:1;  		/* We have the 16-bit (vs 8-bit) version of the card. */
+	unsigned bigendian:1;		/* 16-bit big endian mode. Do NOT */
+					/* set this on random 8390 clones! */
+	unsigned txing:1;		/* Transmit Active */
+	unsigned irqlock:1;		/* 8390's intrs disabled when '1'. */
+	unsigned dmaing:1;		/* Remote DMA Active */
+	unsigned char tx_start_page, rx_start_page, stop_page;
+	unsigned char current_page;	/* Read pointer in buffer  */
+	unsigned char interface_num;	/* Net port (AUI, 10bT.) to use. */
+	unsigned char txqueue;		/* Tx Packet buffer queue length. */
+	short tx1, tx2;			/* Packet lengths for ping-pong tx. */
+	short lasttx;			/* Alpha version consistency check. */
+	unsigned char reg0;		/* Register '0' in a WD8013 */
+	unsigned char reg5;		/* Register '5' in a WD8013 */
+	unsigned char saved_irq;	/* Original dev->irq value. */
+	struct net_device_stats stat;	/* The new statistics table. */
+	u32 *reg_offset;		/* Register mapping table */
+	spinlock_t page_lock;		/* Page register locks */
+	unsigned long priv;		/* Private field to store bus IDs etc. */
+};
+
+/* The maximum number of 8390 interrupt service routines called per IRQ. */
+#define MAX_SERVICE 12
+
+/* The maximum time waited (in jiffies) before assuming a Tx failed. (20ms) */
+#define TX_TIMEOUT (20*HZ/100)
+
+#define ei_status (*(struct ei_device *)netdev_priv(dev))
+
+/* Some generic ethernet register configurations. */
+#define E8390_TX_IRQ_MASK	0xa	/* For register EN0_ISR */
+#define E8390_RX_IRQ_MASK	0x5
+#define E8390_RXCONFIG		0x4	/* EN0_RXCR: broadcasts, no multicast,errors */
+#define E8390_RXOFF		0x20	/* EN0_RXCR: Accept no packets */
+#define E8390_TXCONFIG		0x00	/* EN0_TXCR: Normal transmit mode */
+#define E8390_TXOFF		0x02	/* EN0_TXCR: Transmitter off */
+
+/*  Register accessed at EN_CMD, the 8390 base addr.  */
+#define E8390_STOP	0x01	/* Stop and reset the chip */
+#define E8390_START	0x02	/* Start the chip, clear reset */
+#define E8390_TRANS	0x04	/* Transmit a frame */
+#define E8390_RREAD	0x08	/* Remote read */
+#define E8390_RWRITE	0x10	/* Remote write  */
+#define E8390_NODMA	0x20	/* Remote DMA */
+#define E8390_PAGE0	0x00	/* Select page chip registers */
+#define E8390_PAGE1	0x40	/* using the two high-order bits */
+#define E8390_PAGE2	0x80	/* Page 3 is invalid. */
+
+/*
+ *	Only generate indirect loads given a machine that needs them.
+ *      - removed AMIGA_PCMCIA from this list, handled as ISA io now
+ */
+ 
+#if defined(CONFIG_MAC) ||  \
+    defined(CONFIG_ZORRO8390) || defined(CONFIG_ZORRO8390_MODULE) || \
+    defined(CONFIG_HYDRA) || defined(CONFIG_HYDRA_MODULE)
+#define EI_SHIFT(x)	(ei_local->reg_offset[x])
+#undef inb
+#undef inb_p
+#undef outb
+#undef outb_p
+
+#define inb(port)   in_8(port)
+#define outb(val,port)  out_8(port,val)
+#define inb_p(port)   in_8(port)
+#define outb_p(val,port)  out_8(port,val)
+
+#elif defined(CONFIG_ARM_ETHERH) || defined(CONFIG_ARM_ETHERH_MODULE)
+#define EI_SHIFT(x)	(ei_local->reg_offset[x])
+#undef inb
+#undef inb_p
+#undef outb
+#undef outb_p
+
+#define inb(_p)		readb(_p)
+#define outb(_v,_p)	writeb(_v,_p)
+#define inb_p(_p)	inb(_p)
+#define outb_p(_v,_p)	outb(_v,_p)
+
+#elif defined(CONFIG_NET_CBUS) || defined(CONFIG_NE_H8300) || defined(CONFIG_NE_H8300_MODULE)
+#define EI_SHIFT(x)	(ei_local->reg_offset[x])
+#else
+#define EI_SHIFT(x)	(x)
+#endif
+
+#define E8390_CMD	EI_SHIFT(0x00)  /* The command register (for all pages) */
+/* Page 0 register offsets. */
+#define EN0_CLDALO	EI_SHIFT(0x01)	/* Low byte of current local dma addr  RD */
+#define EN0_STARTPG	EI_SHIFT(0x01)	/* Starting page of ring bfr WR */
+#define EN0_CLDAHI	EI_SHIFT(0x02)	/* High byte of current local dma addr  RD */
+#define EN0_STOPPG	EI_SHIFT(0x02)	/* Ending page +1 of ring bfr WR */
+#define EN0_BOUNDARY	EI_SHIFT(0x03)	/* Boundary page of ring bfr RD WR */
+#define EN0_TSR		EI_SHIFT(0x04)	/* Transmit status reg RD */
+#define EN0_TPSR	EI_SHIFT(0x04)	/* Transmit starting page WR */
+#define EN0_NCR		EI_SHIFT(0x05)	/* Number of collision reg RD */
+#define EN0_TCNTLO	EI_SHIFT(0x05)	/* Low  byte of tx byte count WR */
+#define EN0_FIFO	EI_SHIFT(0x06)	/* FIFO RD */
+#define EN0_TCNTHI	EI_SHIFT(0x06)	/* High byte of tx byte count WR */
+#define EN0_ISR		EI_SHIFT(0x07)	/* Interrupt status reg RD WR */
+#define EN0_CRDALO	EI_SHIFT(0x08)	/* low byte of current remote dma address RD */
+#define EN0_RSARLO	EI_SHIFT(0x08)	/* Remote start address reg 0 */
+#define EN0_CRDAHI	EI_SHIFT(0x09)	/* high byte, current remote dma address RD */
+#define EN0_RSARHI	EI_SHIFT(0x09)	/* Remote start address reg 1 */
+#define EN0_RCNTLO	EI_SHIFT(0x0a)	/* Remote byte count reg WR */
+#define EN0_RCNTHI	EI_SHIFT(0x0b)	/* Remote byte count reg WR */
+#define EN0_RSR		EI_SHIFT(0x0c)	/* rx status reg RD */
+#define EN0_RXCR	EI_SHIFT(0x0c)	/* RX configuration reg WR */
+#define EN0_TXCR	EI_SHIFT(0x0d)	/* TX configuration reg WR */
+#define EN0_COUNTER0	EI_SHIFT(0x0d)	/* Rcv alignment error counter RD */
+#define EN0_DCFG	EI_SHIFT(0x0e)	/* Data configuration reg WR */
+#define EN0_COUNTER1	EI_SHIFT(0x0e)	/* Rcv CRC error counter RD */
+#define EN0_IMR		EI_SHIFT(0x0f)	/* Interrupt mask reg WR */
+#define EN0_COUNTER2	EI_SHIFT(0x0f)	/* Rcv missed frame error counter RD */
+
+/* Bits in EN0_ISR - Interrupt status register */
+#define ENISR_RX	0x01	/* Receiver, no error */
+#define ENISR_TX	0x02	/* Transmitter, no error */
+#define ENISR_RX_ERR	0x04	/* Receiver, with error */
+#define ENISR_TX_ERR	0x08	/* Transmitter, with error */
+#define ENISR_OVER	0x10	/* Receiver overwrote the ring */
+#define ENISR_COUNTERS	0x20	/* Counters need emptying */
+#define ENISR_RDC	0x40	/* remote dma complete */
+#define ENISR_RESET	0x80	/* Reset completed */
+#define ENISR_ALL	0x3f	/* Interrupts we will enable */
+
+/* Bits in EN0_DCFG - Data config register */
+#define ENDCFG_WTS	0x01	/* word transfer mode selection */
+#define ENDCFG_BOS	0x02	/* byte order selection */
+
+/* Page 1 register offsets. */
+#define EN1_PHYS   EI_SHIFT(0x01)	/* This board's physical enet addr RD WR */
+#define EN1_PHYS_SHIFT(i)  EI_SHIFT(i+1) /* Get and set mac address */
+#define EN1_CURPAG EI_SHIFT(0x07)	/* Current memory page RD WR */
+#define EN1_MULT   EI_SHIFT(0x08)	/* Multicast filter mask array (8 bytes) RD WR */
+#define EN1_MULT_SHIFT(i)  EI_SHIFT(8+i) /* Get and set multicast filter */
+
+/* Bits in received packet status byte and EN0_RSR*/
+#define ENRSR_RXOK	0x01	/* Received a good packet */
+#define ENRSR_CRC	0x02	/* CRC error */
+#define ENRSR_FAE	0x04	/* frame alignment error */
+#define ENRSR_FO	0x08	/* FIFO overrun */
+#define ENRSR_MPA	0x10	/* missed pkt */
+#define ENRSR_PHY	0x20	/* physical/multicast address */
+#define ENRSR_DIS	0x40	/* receiver disable. set in monitor mode */
+#define ENRSR_DEF	0x80	/* deferring */
+
+/* Transmitted packet status, EN0_TSR. */
+#define ENTSR_PTX 0x01	/* Packet transmitted without error */
+#define ENTSR_ND  0x02	/* The transmit wasn't deferred. */
+#define ENTSR_COL 0x04	/* The transmit collided at least once. */
+#define ENTSR_ABT 0x08  /* The transmit collided 16 times, and was deferred. */
+#define ENTSR_CRS 0x10	/* The carrier sense was lost. */
+#define ENTSR_FU  0x20  /* A "FIFO underrun" occurred during transmit. */
+#define ENTSR_CDH 0x40	/* The collision detect "heartbeat" signal was lost. */
+#define ENTSR_OWC 0x80  /* There was an out-of-window collision. */
+
+#endif /* _8390_h */