Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC updates from Olof Johansson:
 "This contains the bulk of new SoC development for this merge window.

  Two new platforms have been added, the sunxi platforms (Allwinner A1x
  SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
  series of ARMv7 platforms from them, where the hope is that we can
  keep the platform code generic enough to have them all share one mach
  directory.  The new Broadcom platform is contributed by Christian
  Daudt.

  Highbank has grown support for Calxeda's next generation of hardware,
  ECX-2000.

  clps711x has seen a lot of cleanup from Alexander Shiyan, and he's
  also taken on maintainership of the platform.

  Beyond this there has been a bunch of work from a number of people on
  converting more platforms to IRQ domains, pinctrl conversion, cleanup
  and general feature enablement across most of the active platforms."

Fix up trivial conflicts as per Olof.

* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits)
  mfd: vexpress-sysreg: Remove LEDs code
  irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids
  clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids
  irq: versatile: delete dangling variable
  ARM: sunxi: add missing include for mdelay()
  ARM: EXYNOS: Avoid early use of of_machine_is_compatible()
  ARM: dts: add node for PL330 MDMA1 controller for exynos4
  ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
  ARM: EXYNOS: add UART3 to DEBUG_LL ports
  ARM: S3C24XX: Add clkdev entry for camif-upll clock
  ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
  ARM: sunxi: Add missing sun4i.dtsi file
  pinctrl: samsung: Do not initialise statics to 0
  ARM i.MX6: remove gate_mask from pllv3
  ARM i.MX6: Fix ethernet PLL clocks
  ARM i.MX6: rename PLLs according to datasheet
  ARM i.MX6: Add pwm support
  ARM i.MX51: Add pwm support
  ARM i.MX53: Add pwm support
  ARM: mx5: Replace clk_register_clkdev with clock DT lookup
  ...

4 files changed, 0 insertions, 428 deletions

diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 4883139460b..531807dec6b 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -49,13 +49,6 @@ config MTD_NAND_MUSEUM_IDS
 	  NAND chips (page size 256 byte, erase size 4-8KiB). The IDs
 	  of these chips were reused by later, larger chips.
 
-config MTD_NAND_AUTCPU12
-	tristate "SmartMediaCard on autronix autcpu12 board"
-	depends on ARCH_AUTCPU12
-	help
-	  This enables the driver for the autronix autcpu12 board to
-	  access the SmartMediaCard.
-
 config MTD_NAND_DENALI
        depends on PCI
         tristate "Support Denali NAND controller on Intel Moorestown"
@@ -86,12 +79,6 @@ config MTD_NAND_GPIO
 	help
 	  This enables a GPIO based NAND flash driver.
 
-config MTD_NAND_SPIA
-	tristate "NAND Flash device on SPIA board"
-	depends on ARCH_P720T
-	help
-	  If you had to ask, you don't have one. Say 'N'.
-
 config MTD_NAND_AMS_DELTA
 	tristate "NAND Flash device on Amstrad E3"
 	depends on MACH_AMS_DELTA
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 2cbd0916b73..6c7f2b3ca8a 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -9,9 +9,7 @@ obj-$(CONFIG_MTD_NAND_IDS)		+= nand_ids.o
 obj-$(CONFIG_MTD_SM_COMMON) 		+= sm_common.o
 
 obj-$(CONFIG_MTD_NAND_CAFE)		+= cafe_nand.o
-obj-$(CONFIG_MTD_NAND_SPIA)		+= spia.o
 obj-$(CONFIG_MTD_NAND_AMS_DELTA)	+= ams-delta.o
-obj-$(CONFIG_MTD_NAND_AUTCPU12)		+= autcpu12.o
 obj-$(CONFIG_MTD_NAND_DENALI)		+= denali.o
 obj-$(CONFIG_MTD_NAND_AU1550)		+= au1550nd.o
 obj-$(CONFIG_MTD_NAND_BF5XX)		+= bf5xx_nand.o
diff --git a/drivers/mtd/nand/autcpu12.c b/drivers/mtd/nand/autcpu12.c
deleted file mode 100644
index 04769a49a7c..00000000000
--- a/drivers/mtd/nand/autcpu12.c
+++ /dev/null
@@ -1,237 +0,0 @@
-/*
- *  drivers/mtd/autcpu12.c
- *
- *  Copyright (c) 2002 Thomas Gleixner <tgxl@linutronix.de>
- *
- *  Derived from drivers/mtd/spia.c
- *	 Copyright (C) 2000 Steven J. Hill (sjhill@realitydiluted.com)
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  Overview:
- *   This is a device driver for the NAND flash device found on the
- *   autronix autcpu12 board, which is a SmartMediaCard. It supports
- *   16MiB, 32MiB and 64MiB cards.
- *
- *
- *	02-12-2002 TG	Cleanup of module params
- *
- *	02-20-2002 TG	adjusted for different rd/wr address support
- *			added support for read device ready/busy line
- *			added page_cache
- *
- *	10-06-2002 TG	128K card support added
- */
-
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/module.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-#include <asm/io.h>
-#include <mach/hardware.h>
-#include <asm/sizes.h>
-#include <mach/autcpu12.h>
-
-/*
- * MTD structure for AUTCPU12 board
- */
-static struct mtd_info *autcpu12_mtd = NULL;
-static void __iomem *autcpu12_fio_base;
-
-/*
- * Define partitions for flash devices
- */
-static struct mtd_partition partition_info16k[] = {
-	{ .name		= "AUTCPU12 flash partition 1",
-	  .offset	= 0,
-	  .size		= 8 * SZ_1M },
-	{ .name		= "AUTCPU12 flash partition 2",
-	  .offset	= 8 * SZ_1M,
-	  .size		= 8 * SZ_1M },
-};
-
-static struct mtd_partition partition_info32k[] = {
-	{ .name		= "AUTCPU12 flash partition 1",
-	  .offset	= 0,
-	  .size		= 8 * SZ_1M },
-	{ .name		= "AUTCPU12 flash partition 2",
-	  .offset	= 8 * SZ_1M,
-	  .size		= 24 * SZ_1M },
-};
-
-static struct mtd_partition partition_info64k[] = {
-	{ .name		= "AUTCPU12 flash partition 1",
-	  .offset	= 0,
-	  .size		= 16 * SZ_1M },
-	{ .name		= "AUTCPU12 flash partition 2",
-	  .offset	= 16 * SZ_1M,
-	  .size		= 48 * SZ_1M },
-};
-
-static struct mtd_partition partition_info128k[] = {
-	{ .name		= "AUTCPU12 flash partition 1",
-	  .offset	= 0,
-	  .size		= 16 * SZ_1M },
-	{ .name		= "AUTCPU12 flash partition 2",
-	  .offset	= 16 * SZ_1M,
-	  .size		= 112 * SZ_1M },
-};
-
-#define NUM_PARTITIONS16K 2
-#define NUM_PARTITIONS32K 2
-#define NUM_PARTITIONS64K 2
-#define NUM_PARTITIONS128K 2
-/*
- *	hardware specific access to control-lines
- *
- *	ALE bit 4 autcpu12_pedr
- *	CLE bit 5 autcpu12_pedr
- *	NCE bit 0 fio_ctrl
- *
- */
-static void autcpu12_hwcontrol(struct mtd_info *mtd, int cmd,
-			       unsigned int ctrl)
-{
-	struct nand_chip *chip = mtd->priv;
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		void __iomem *addr;
-		unsigned char bits;
-
-		bits = clps_readb(AUTCPU12_SMC_PORT_OFFSET) & ~0x30;
-		bits |= (ctrl & NAND_CLE) << 4;
-		bits |= (ctrl & NAND_ALE) << 2;
-		clps_writeb(bits, AUTCPU12_SMC_PORT_OFFSET);
-
-		addr = autcpu12_fio_base + AUTCPU12_SMC_SELECT_OFFSET;
-		writeb((readb(addr) & ~0x1) | (ctrl & NAND_NCE), addr);
-	}
-
-	if (cmd != NAND_CMD_NONE)
-		writeb(cmd, chip->IO_ADDR_W);
-}
-
-/*
- *	read device ready pin
- */
-int autcpu12_device_ready(struct mtd_info *mtd)
-{
-	return clps_readb(AUTCPU12_SMC_PORT_OFFSET) & AUTCPU12_SMC_RDY;
-}
-
-/*
- * Main initialization routine
- */
-static int __init autcpu12_init(void)
-{
-	struct nand_chip *this;
-	int err = 0;
-
-	/* Allocate memory for MTD device structure and private data */
-	autcpu12_mtd = kmalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip),
-			       GFP_KERNEL);
-	if (!autcpu12_mtd) {
-		printk("Unable to allocate AUTCPU12 NAND MTD device structure.\n");
-		err = -ENOMEM;
-		goto out;
-	}
-
-	/* map physical address */
-	autcpu12_fio_base = ioremap(AUTCPU12_PHYS_SMC, SZ_1K);
-	if (!autcpu12_fio_base) {
-		printk("Ioremap autcpu12 SmartMedia Card failed\n");
-		err = -EIO;
-		goto out_mtd;
-	}
-
-	/* Get pointer to private data */
-	this = (struct nand_chip *)(&autcpu12_mtd[1]);
-
-	/* Initialize structures */
-	memset(autcpu12_mtd, 0, sizeof(struct mtd_info));
-	memset(this, 0, sizeof(struct nand_chip));
-
-	/* Link the private data with the MTD structure */
-	autcpu12_mtd->priv = this;
-	autcpu12_mtd->owner = THIS_MODULE;
-
-	/* Set address of NAND IO lines */
-	this->IO_ADDR_R = autcpu12_fio_base;
-	this->IO_ADDR_W = autcpu12_fio_base;
-	this->cmd_ctrl = autcpu12_hwcontrol;
-	this->dev_ready = autcpu12_device_ready;
-	/* 20 us command delay time */
-	this->chip_delay = 20;
-	this->ecc.mode = NAND_ECC_SOFT;
-
-	/* Enable the following for a flash based bad block table */
-	/*
-	   this->bbt_options = NAND_BBT_USE_FLASH;
-	 */
-	this->bbt_options = NAND_BBT_USE_FLASH;
-
-	/* Scan to find existence of the device */
-	if (nand_scan(autcpu12_mtd, 1)) {
-		err = -ENXIO;
-		goto out_ior;
-	}
-
-	/* Register the partitions */
-	switch (autcpu12_mtd->size) {
-		case SZ_16M:
-			mtd_device_register(autcpu12_mtd, partition_info16k,
-					    NUM_PARTITIONS16K);
-			break;
-		case SZ_32M:
-			mtd_device_register(autcpu12_mtd, partition_info32k,
-					    NUM_PARTITIONS32K);
-			break;
-		case SZ_64M:
-			mtd_device_register(autcpu12_mtd, partition_info64k,
-					    NUM_PARTITIONS64K);
-			break;
-		case SZ_128M:
-			mtd_device_register(autcpu12_mtd, partition_info128k,
-					    NUM_PARTITIONS128K);
-			break;
-		default:
-			printk("Unsupported SmartMedia device\n");
-			err = -ENXIO;
-			goto out_ior;
-	}
-	goto out;
-
- out_ior:
-	iounmap(autcpu12_fio_base);
- out_mtd:
-	kfree(autcpu12_mtd);
- out:
-	return err;
-}
-
-module_init(autcpu12_init);
-
-/*
- * Clean up routine
- */
-static void __exit autcpu12_cleanup(void)
-{
-	/* Release resources, unregister device */
-	nand_release(autcpu12_mtd);
-
-	/* unmap physical address */
-	iounmap(autcpu12_fio_base);
-
-	/* Free the MTD device structure */
-	kfree(autcpu12_mtd);
-}
-
-module_exit(autcpu12_cleanup);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Thomas Gleixner <tglx@linutronix.de>");
-MODULE_DESCRIPTION("Glue layer for SmartMediaCard on autronix autcpu12");
diff --git a/drivers/mtd/nand/spia.c b/drivers/mtd/nand/spia.c
deleted file mode 100644
index bef76cd7c24..00000000000
--- a/drivers/mtd/nand/spia.c
+++ /dev/null
@@ -1,176 +0,0 @@
-/*
- *  drivers/mtd/nand/spia.c
- *
- *  Copyright (C) 2000 Steven J. Hill (sjhill@realitydiluted.com)
- *
- *
- *	10-29-2001 TG	change to support hardwarespecific access
- *			to controllines	(due to change in nand.c)
- *			page_cache added
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  Overview:
- *   This is a device driver for the NAND flash device found on the
- *   SPIA board which utilizes the Toshiba TC58V64AFT part. This is
- *   a 64Mibit (8MiB x 8 bits) NAND flash device.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/module.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/partitions.h>
-#include <asm/io.h>
-
-/*
- * MTD structure for SPIA board
- */
-static struct mtd_info *spia_mtd = NULL;
-
-/*
- * Values specific to the SPIA board (used with EP7212 processor)
- */
-#define SPIA_IO_BASE	0xd0000000	/* Start of EP7212 IO address space */
-#define SPIA_FIO_BASE	0xf0000000	/* Address where flash is mapped */
-#define SPIA_PEDR	0x0080	/*
-				 * IO offset to Port E data register
-				 * where the CLE, ALE and NCE pins
-				 * are wired to.
-				 */
-#define SPIA_PEDDR	0x00c0	/*
-				 * IO offset to Port E data direction
-				 * register so we can control the IO
-				 * lines.
-				 */
-
-/*
- * Module stuff
- */
-
-static int spia_io_base = SPIA_IO_BASE;
-static int spia_fio_base = SPIA_FIO_BASE;
-static int spia_pedr = SPIA_PEDR;
-static int spia_peddr = SPIA_PEDDR;
-
-module_param(spia_io_base, int, 0);
-module_param(spia_fio_base, int, 0);
-module_param(spia_pedr, int, 0);
-module_param(spia_peddr, int, 0);
-
-/*
- * Define partitions for flash device
- */
-static const struct mtd_partition partition_info[] = {
-	{
-	 .name = "SPIA flash partition 1",
-	 .offset = 0,
-	 .size = 2 * 1024 * 1024},
-	{
-	 .name = "SPIA flash partition 2",
-	 .offset = 2 * 1024 * 1024,
-	 .size = 6 * 1024 * 1024}
-};
-
-#define NUM_PARTITIONS 2
-
-/*
- *	hardware specific access to control-lines
- *
- *	ctrl:
- *	NAND_CNE: bit 0 -> bit 2
- *	NAND_CLE: bit 1 -> bit 0
- *	NAND_ALE: bit 2 -> bit 1
- */
-static void spia_hwcontrol(struct mtd_info *mtd, int cmd)
-{
-	struct nand_chip *chip = mtd->priv;
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		void __iomem *addr = spia_io_base + spia_pedr;
-		unsigned char bits;
-
-		bits = (ctrl & NAND_CNE) << 2;
-		bits |= (ctrl & NAND_CLE | NAND_ALE) >> 1;
-		writeb((readb(addr) & ~0x7) | bits, addr);
-	}
-
-	if (cmd != NAND_CMD_NONE)
-		writeb(cmd, chip->IO_ADDR_W);
-}
-
-/*
- * Main initialization routine
- */
-static int __init spia_init(void)
-{
-	struct nand_chip *this;
-
-	/* Allocate memory for MTD device structure and private data */
-	spia_mtd = kmalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip), GFP_KERNEL);
-	if (!spia_mtd) {
-		printk("Unable to allocate SPIA NAND MTD device structure.\n");
-		return -ENOMEM;
-	}
-
-	/* Get pointer to private data */
-	this = (struct nand_chip *)(&spia_mtd[1]);
-
-	/* Initialize structures */
-	memset(spia_mtd, 0, sizeof(struct mtd_info));
-	memset(this, 0, sizeof(struct nand_chip));
-
-	/* Link the private data with the MTD structure */
-	spia_mtd->priv = this;
-	spia_mtd->owner = THIS_MODULE;
-
-	/*
-	 * Set GPIO Port E control register so that the pins are configured
-	 * to be outputs for controlling the NAND flash.
-	 */
-	(*(volatile unsigned char *)(spia_io_base + spia_peddr)) = 0x07;
-
-	/* Set address of NAND IO lines */
-	this->IO_ADDR_R = (void __iomem *)spia_fio_base;
-	this->IO_ADDR_W = (void __iomem *)spia_fio_base;
-	/* Set address of hardware control function */
-	this->cmd_ctrl = spia_hwcontrol;
-	/* 15 us command delay time */
-	this->chip_delay = 15;
-
-	/* Scan to find existence of the device */
-	if (nand_scan(spia_mtd, 1)) {
-		kfree(spia_mtd);
-		return -ENXIO;
-	}
-
-	/* Register the partitions */
-	mtd_device_register(spia_mtd, partition_info, NUM_PARTITIONS);
-
-	/* Return happy */
-	return 0;
-}
-
-module_init(spia_init);
-
-/*
- * Clean up routine
- */
-static void __exit spia_cleanup(void)
-{
-	/* Release resources, unregister device */
-	nand_release(spia_mtd);
-
-	/* Free the MTD device structure */
-	kfree(spia_mtd);
-}
-
-module_exit(spia_cleanup);
-
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Steven J. Hill <sjhill@realitydiluted.com");
-MODULE_DESCRIPTION("Board-specific glue layer for NAND flash on SPIA board");