mmc: require explicit support for high-speed

The new high-speed timings are similar to each other and the old
system, but not identical. And although things "just work" most of
the time, sometimes it does not. So we need to start marking which
hosts are known to fully comply with the new timings.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

1 files changed, 10 insertions, 15 deletions

diff --git a/drivers/mmc/sdhci.c b/drivers/mmc/sdhci.c
index 7522f76b15e..c52b167e858 100644
--- a/drivers/mmc/sdhci.c
+++ b/drivers/mmc/sdhci.c
@@ -606,7 +606,6 @@ static void sdhci_finish_command(struct sdhci_host *host)
 static void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
 {
 	int div;
-	u8 ctrl;
 	u16 clk;
 	unsigned long timeout;
 
@@ -615,13 +614,6 @@ static void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
 
 	writew(0, host->ioaddr + SDHCI_CLOCK_CONTROL);
 
-	ctrl = readb(host->ioaddr + SDHCI_HOST_CONTROL);
-	if (clock > 25000000)
-		ctrl |= SDHCI_CTRL_HISPD;
-	else
-		ctrl &= ~SDHCI_CTRL_HISPD;
-	writeb(ctrl, host->ioaddr + SDHCI_HOST_CONTROL);
-
 	if (clock == 0)
 		goto out;
 
@@ -761,10 +753,17 @@ static void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 		sdhci_set_power(host, ios->vdd);
 
 	ctrl = readb(host->ioaddr + SDHCI_HOST_CONTROL);
+
 	if (ios->bus_width == MMC_BUS_WIDTH_4)
 		ctrl |= SDHCI_CTRL_4BITBUS;
 	else
 		ctrl &= ~SDHCI_CTRL_4BITBUS;
+
+	if (ios->timing == MMC_TIMING_SD_HS)
+		ctrl |= SDHCI_CTRL_HISPD;
+	else
+		ctrl &= ~SDHCI_CTRL_HISPD;
+
 	writeb(ctrl, host->ioaddr + SDHCI_HOST_CONTROL);
 
 	mmiowb();
@@ -1274,6 +1273,9 @@ static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot)
 	mmc->f_max = host->max_clk;
 	mmc->caps = MMC_CAP_4_BIT_DATA | MMC_CAP_MULTIWRITE | MMC_CAP_BYTEBLOCK;
 
+	if (caps & SDHCI_CAN_DO_HISPD)
+		mmc->caps |= MMC_CAP_SD_HIGHSPEED;
+
 	mmc->ocr_avail = 0;
 	if (caps & SDHCI_CAN_VDD_330)
 		mmc->ocr_avail |= MMC_VDD_32_33|MMC_VDD_33_34;
@@ -1282,13 +1284,6 @@ static int __devinit sdhci_probe_slot(struct pci_dev *pdev, int slot)
 	if (caps & SDHCI_CAN_VDD_180)
 		mmc->ocr_avail |= MMC_VDD_17_18|MMC_VDD_18_19;
 
-	if ((host->max_clk > 25000000) && !(caps & SDHCI_CAN_DO_HISPD)) {
-		printk(KERN_ERR "%s: Controller reports > 25 MHz base clock,"
-			" but no high speed support.\n",
-			host->slot_descr);
-		mmc->f_max = 25000000;
-	}
-
 	if (mmc->ocr_avail == 0) {
 		printk(KERN_ERR "%s: Hardware doesn't report any "
 			"support voltages.\n", host->slot_descr);