mmc: sd: add support for uhs bus speed mode selection

This patch adds support for setting UHS-I bus speed mode during UHS-I
initialization procedure. Since both the host and card can support
more than one bus speed, we select the highest speed based on both of
their capabilities. First we set the bus speed mode for the card using
CMD6 mode 1, and then we program the host controller to support the
required speed mode. We also set High Speed Enable in case one of the
UHS-I modes is selected. We take care to reset SD clock before setting
UHS mode in the Host Control2 register, and then re-enable it as per
the Host Controller spec v3.00. We then set the clock frequency for
the UHS-I mode selected.

Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.

Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

1 files changed, 65 insertions, 0 deletions

diff --git a/drivers/mmc/core/sd.c b/drivers/mmc/core/sd.c
index 5b7c9985563..6970b82171f 100644
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
@@ -452,6 +452,66 @@ static int sd_select_driver_type(struct mmc_card *card, u8 *status)
 	return 0;
 }
 
+static int sd_set_bus_speed_mode(struct mmc_card *card, u8 *status)
+{
+	unsigned int bus_speed = 0, timing = 0;
+	int err;
+
+	/*
+	 * If the host doesn't support any of the UHS-I modes, fallback on
+	 * default speed.
+	 */
+	if (!(card->host->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
+	    MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_DDR50)))
+		return 0;
+
+	if ((card->host->caps & MMC_CAP_UHS_SDR104) &&
+	    (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR104)) {
+			bus_speed = UHS_SDR104_BUS_SPEED;
+			timing = MMC_TIMING_UHS_SDR104;
+			card->sw_caps.uhs_max_dtr = UHS_SDR104_MAX_DTR;
+	} else if ((card->host->caps & MMC_CAP_UHS_DDR50) &&
+		   (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_DDR50)) {
+			bus_speed = UHS_DDR50_BUS_SPEED;
+			timing = MMC_TIMING_UHS_DDR50;
+			card->sw_caps.uhs_max_dtr = UHS_DDR50_MAX_DTR;
+	} else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
+		    MMC_CAP_UHS_SDR50)) && (card->sw_caps.sd3_bus_mode &
+		    SD_MODE_UHS_SDR50)) {
+			bus_speed = UHS_SDR50_BUS_SPEED;
+			timing = MMC_TIMING_UHS_SDR50;
+			card->sw_caps.uhs_max_dtr = UHS_SDR50_MAX_DTR;
+	} else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
+		    MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25)) &&
+		   (card->sw_caps.sd3_bus_mode & SD_MODE_UHS_SDR25)) {
+			bus_speed = UHS_SDR25_BUS_SPEED;
+			timing = MMC_TIMING_UHS_SDR25;
+			card->sw_caps.uhs_max_dtr = UHS_SDR25_MAX_DTR;
+	} else if ((card->host->caps & (MMC_CAP_UHS_SDR104 |
+		    MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR25 |
+		    MMC_CAP_UHS_SDR12)) && (card->sw_caps.sd3_bus_mode &
+		    SD_MODE_UHS_SDR12)) {
+			bus_speed = UHS_SDR12_BUS_SPEED;
+			timing = MMC_TIMING_UHS_SDR12;
+			card->sw_caps.uhs_max_dtr = UHS_SDR12_MAX_DTR;
+	}
+
+	card->sd_bus_speed = bus_speed;
+	err = mmc_sd_switch(card, 1, 0, bus_speed, status);
+	if (err)
+		return err;
+
+	if ((status[16] & 0xF) != bus_speed)
+		printk(KERN_WARNING "%s: Problem setting bus speed mode!\n",
+			mmc_hostname(card->host));
+	else {
+		mmc_set_timing(card->host, timing);
+		mmc_set_clock(card->host, card->sw_caps.uhs_max_dtr);
+	}
+
+	return 0;
+}
+
 /*
  * UHS-I specific initialization procedure
  */
@@ -485,6 +545,11 @@ static int mmc_sd_init_uhs_card(struct mmc_card *card)
 
 	/* Set the driver strength for the card */
 	err = sd_select_driver_type(card, status);
+	if (err)
+		goto out;
+
+	/* Set bus speed mode of the card */
+	err = sd_set_bus_speed_mode(card, status);
 
 out:
 	kfree(status);