ide: remove useless subdirs from drivers/ide/

Suggested-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

1 files changed, 480 insertions, 0 deletions

diff --git a/drivers/ide/piix.c b/drivers/ide/piix.c
new file mode 100644
index 00000000000..d63f9fdca76
--- /dev/null
+++ b/drivers/ide/piix.c
@@ -0,0 +1,480 @@
+/*
+ *  Copyright (C) 1998-1999 Andrzej Krzysztofowicz, Author and Maintainer
+ *  Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
+ *  Copyright (C) 2003 Red Hat Inc <alan@redhat.com>
+ *  Copyright (C) 2006-2007 MontaVista Software, Inc. <source@mvista.com>
+ *
+ *  May be copied or modified under the terms of the GNU General Public License
+ *
+ * Documentation:
+ *
+ *	Publically available from Intel web site. Errata documentation
+ * is also publically available. As an aide to anyone hacking on this
+ * driver the list of errata that are relevant is below.going back to
+ * PIIX4. Older device documentation is now a bit tricky to find.
+ *
+ * Errata of note:
+ *
+ * Unfixable
+ *	PIIX4    errata #9	- Only on ultra obscure hw
+ *	ICH3	 errata #13     - Not observed to affect real hw
+ *				  by Intel
+ *
+ * Things we must deal with
+ *	PIIX4	errata #10	- BM IDE hang with non UDMA
+ *				  (must stop/start dma to recover)
+ *	440MX   errata #15	- As PIIX4 errata #10
+ *	PIIX4	errata #15	- Must not read control registers
+ * 				  during a PIO transfer
+ *	440MX   errata #13	- As PIIX4 errata #15
+ *	ICH2	errata #21	- DMA mode 0 doesn't work right
+ *	ICH0/1  errata #55	- As ICH2 errata #21
+ *	ICH2	spec c #9	- Extra operations needed to handle
+ *				  drive hotswap [NOT YET SUPPORTED]
+ *	ICH2    spec c #20	- IDE PRD must not cross a 64K boundary
+ *				  and must be dword aligned
+ *	ICH2    spec c #24	- UDMA mode 4,5 t85/86 should be 6ns not 3.3
+ *
+ * Should have been BIOS fixed:
+ *	450NX:	errata #19	- DMA hangs on old 450NX
+ *	450NX:  errata #20	- DMA hangs on old 450NX
+ *	450NX:  errata #25	- Corruption with DMA on old 450NX
+ *	ICH3    errata #15      - IDE deadlock under high load
+ *				  (BIOS must set dev 31 fn 0 bit 23)
+ *	ICH3	errata #18	- Don't use native mode
+ */
+
+#include <linux/types.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+#define DRV_NAME "piix"
+
+static int no_piix_dma;
+
+/**
+ *	piix_set_pio_mode	-	set host controller for PIO mode
+ *	@drive: drive
+ *	@pio: PIO mode number
+ *
+ *	Set the interface PIO mode based upon the settings done by AMI BIOS.
+ */
+
+static void piix_set_pio_mode(ide_drive_t *drive, const u8 pio)
+{
+	ide_hwif_t *hwif	= HWIF(drive);
+	struct pci_dev *dev	= to_pci_dev(hwif->dev);
+	int is_slave		= drive->dn & 1;
+	int master_port		= hwif->channel ? 0x42 : 0x40;
+	int slave_port		= 0x44;
+	unsigned long flags;
+	u16 master_data;
+	u8 slave_data;
+	static DEFINE_SPINLOCK(tune_lock);
+	int control = 0;
+
+				     /* ISP  RTC */
+	static const u8 timings[][2]= {
+					{ 0, 0 },
+					{ 0, 0 },
+					{ 1, 0 },
+					{ 2, 1 },
+					{ 2, 3 }, };
+
+	/*
+	 * Master vs slave is synchronized above us but the slave register is
+	 * shared by the two hwifs so the corner case of two slave timeouts in
+	 * parallel must be locked.
+	 */
+	spin_lock_irqsave(&tune_lock, flags);
+	pci_read_config_word(dev, master_port, &master_data);
+
+	if (pio > 1)
+		control |= 1;	/* Programmable timing on */
+	if (drive->media == ide_disk)
+		control |= 4;	/* Prefetch, post write */
+	if (pio > 2)
+		control |= 2;	/* IORDY */
+	if (is_slave) {
+		master_data |=  0x4000;
+		master_data &= ~0x0070;
+		if (pio > 1) {
+			/* Set PPE, IE and TIME */
+			master_data |= control << 4;
+		}
+		pci_read_config_byte(dev, slave_port, &slave_data);
+		slave_data &= hwif->channel ? 0x0f : 0xf0;
+		slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) <<
+			       (hwif->channel ? 4 : 0);
+	} else {
+		master_data &= ~0x3307;
+		if (pio > 1) {
+			/* enable PPE, IE and TIME */
+			master_data |= control;
+		}
+		master_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8);
+	}
+	pci_write_config_word(dev, master_port, master_data);
+	if (is_slave)
+		pci_write_config_byte(dev, slave_port, slave_data);
+	spin_unlock_irqrestore(&tune_lock, flags);
+}
+
+/**
+ *	piix_set_dma_mode	-	set host controller for DMA mode
+ *	@drive: drive
+ *	@speed: DMA mode
+ *
+ *	Set a PIIX host controller to the desired DMA mode.  This involves
+ *	programming the right timing data into the PCI configuration space.
+ */
+
+static void piix_set_dma_mode(ide_drive_t *drive, const u8 speed)
+{
+	ide_hwif_t *hwif	= HWIF(drive);
+	struct pci_dev *dev	= to_pci_dev(hwif->dev);
+	u8 maslave		= hwif->channel ? 0x42 : 0x40;
+	int a_speed		= 3 << (drive->dn * 4);
+	int u_flag		= 1 << drive->dn;
+	int v_flag		= 0x01 << drive->dn;
+	int w_flag		= 0x10 << drive->dn;
+	int u_speed		= 0;
+	int			sitre;
+	u16			reg4042, reg4a;
+	u8			reg48, reg54, reg55;
+
+	pci_read_config_word(dev, maslave, &reg4042);
+	sitre = (reg4042 & 0x4000) ? 1 : 0;
+	pci_read_config_byte(dev, 0x48, &reg48);
+	pci_read_config_word(dev, 0x4a, &reg4a);
+	pci_read_config_byte(dev, 0x54, &reg54);
+	pci_read_config_byte(dev, 0x55, &reg55);
+
+	if (speed >= XFER_UDMA_0) {
+		u8 udma = speed - XFER_UDMA_0;
+
+		u_speed = min_t(u8, 2 - (udma & 1), udma) << (drive->dn * 4);
+
+		if (!(reg48 & u_flag))
+			pci_write_config_byte(dev, 0x48, reg48 | u_flag);
+		if (speed == XFER_UDMA_5) {
+			pci_write_config_byte(dev, 0x55, (u8) reg55|w_flag);
+		} else {
+			pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+		}
+		if ((reg4a & a_speed) != u_speed)
+			pci_write_config_word(dev, 0x4a, (reg4a & ~a_speed) | u_speed);
+		if (speed > XFER_UDMA_2) {
+			if (!(reg54 & v_flag))
+				pci_write_config_byte(dev, 0x54, reg54 | v_flag);
+		} else
+			pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
+	} else {
+		const u8 mwdma_to_pio[] = { 0, 3, 4 };
+		u8 pio;
+
+		if (reg48 & u_flag)
+			pci_write_config_byte(dev, 0x48, reg48 & ~u_flag);
+		if (reg4a & a_speed)
+			pci_write_config_word(dev, 0x4a, reg4a & ~a_speed);
+		if (reg54 & v_flag)
+			pci_write_config_byte(dev, 0x54, reg54 & ~v_flag);
+		if (reg55 & w_flag)
+			pci_write_config_byte(dev, 0x55, (u8) reg55 & ~w_flag);
+
+		if (speed >= XFER_MW_DMA_0)
+			pio = mwdma_to_pio[speed - XFER_MW_DMA_0];
+		else
+			pio = 2; /* only SWDMA2 is allowed */
+
+		piix_set_pio_mode(drive, pio);
+	}
+}
+
+/**
+ *	init_chipset_ich	-	set up the ICH chipset
+ *	@dev: PCI device to set up
+ *
+ *	Initialize the PCI device as required.  For the ICH this turns
+ *	out to be nice and simple.
+ */
+
+static unsigned int init_chipset_ich(struct pci_dev *dev)
+{
+	u32 extra = 0;
+
+	pci_read_config_dword(dev, 0x54, &extra);
+	pci_write_config_dword(dev, 0x54, extra | 0x400);
+
+	return 0;
+}
+
+/**
+ *	ich_clear_irq	-	clear BMDMA status
+ *	@drive: IDE drive
+ *
+ *	ICHx contollers set DMA INTR no matter DMA or PIO.
+ *	BMDMA status might need to be cleared even for
+ *	PIO interrupts to prevent spurious/lost IRQ.
+ */
+static void ich_clear_irq(ide_drive_t *drive)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	u8 dma_stat;
+
+	/*
+	 * ide_dma_end() needs BMDMA status for error checking.
+	 * So, skip clearing BMDMA status here and leave it
+	 * to ide_dma_end() if this is DMA interrupt.
+	 */
+	if (drive->waiting_for_dma || hwif->dma_base == 0)
+		return;
+
+	/* clear the INTR & ERROR bits */
+	dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS);
+	/* Should we force the bit as well ? */
+	outb(dma_stat, hwif->dma_base + ATA_DMA_STATUS);
+}
+
+struct ich_laptop {
+	u16 device;
+	u16 subvendor;
+	u16 subdevice;
+};
+
+/*
+ *	List of laptops that use short cables rather than 80 wire
+ */
+
+static const struct ich_laptop ich_laptop[] = {
+	/* devid, subvendor, subdev */
+	{ 0x27DF, 0x1025, 0x0102 },	/* ICH7 on Acer 5602aWLMi */
+	{ 0x27DF, 0x0005, 0x0280 },	/* ICH7 on Acer 5602WLMi */
+	{ 0x27DF, 0x1025, 0x0110 },	/* ICH7 on Acer 3682WLMi */
+	{ 0x27DF, 0x1043, 0x1267 },	/* ICH7 on Asus W5F */
+	{ 0x27DF, 0x103C, 0x30A1 },	/* ICH7 on HP Compaq nc2400 */
+	{ 0x27DF, 0x1071, 0xD221 },	/* ICH7 on Hercules EC-900 */
+	{ 0x24CA, 0x1025, 0x0061 },	/* ICH4 on Acer Aspire 2023WLMi */
+	{ 0x2653, 0x1043, 0x82D8 },	/* ICH6M on Asus Eee 701 */
+	/* end marker */
+	{ 0, }
+};
+
+static u8 piix_cable_detect(ide_hwif_t *hwif)
+{
+	struct pci_dev *pdev = to_pci_dev(hwif->dev);
+	const struct ich_laptop *lap = &ich_laptop[0];
+	u8 reg54h = 0, mask = hwif->channel ? 0xc0 : 0x30;
+
+	/* check for specials */
+	while (lap->device) {
+		if (lap->device == pdev->device &&
+		    lap->subvendor == pdev->subsystem_vendor &&
+		    lap->subdevice == pdev->subsystem_device) {
+			return ATA_CBL_PATA40_SHORT;
+		}
+		lap++;
+	}
+
+	pci_read_config_byte(pdev, 0x54, &reg54h);
+
+	return (reg54h & mask) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
+}
+
+/**
+ *	init_hwif_piix		-	fill in the hwif for the PIIX
+ *	@hwif: IDE interface
+ *
+ *	Set up the ide_hwif_t for the PIIX interface according to the
+ *	capabilities of the hardware.
+ */
+
+static void __devinit init_hwif_piix(ide_hwif_t *hwif)
+{
+	if (!hwif->dma_base)
+		return;
+
+	if (no_piix_dma)
+		hwif->ultra_mask = hwif->mwdma_mask = hwif->swdma_mask = 0;
+}
+
+static const struct ide_port_ops piix_port_ops = {
+	.set_pio_mode		= piix_set_pio_mode,
+	.set_dma_mode		= piix_set_dma_mode,
+	.cable_detect		= piix_cable_detect,
+};
+
+static const struct ide_port_ops ich_port_ops = {
+	.set_pio_mode		= piix_set_pio_mode,
+	.set_dma_mode		= piix_set_dma_mode,
+	.clear_irq		= ich_clear_irq,
+	.cable_detect		= piix_cable_detect,
+};
+
+#ifndef CONFIG_IA64
+ #define IDE_HFLAGS_PIIX IDE_HFLAG_LEGACY_IRQS
+#else
+ #define IDE_HFLAGS_PIIX 0
+#endif
+
+#define DECLARE_PIIX_DEV(udma) \
+	{						\
+		.name		= DRV_NAME,		\
+		.init_hwif	= init_hwif_piix,	\
+		.enablebits	= {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
+		.port_ops	= &piix_port_ops,	\
+		.host_flags	= IDE_HFLAGS_PIIX,	\
+		.pio_mask	= ATA_PIO4,		\
+		.swdma_mask	= ATA_SWDMA2_ONLY,	\
+		.mwdma_mask	= ATA_MWDMA12_ONLY,	\
+		.udma_mask	= udma,			\
+	}
+
+#define DECLARE_ICH_DEV(udma) \
+	{ \
+		.name		= DRV_NAME, \
+		.init_chipset	= init_chipset_ich, \
+		.init_hwif	= init_hwif_piix, \
+		.enablebits	= {{0x41,0x80,0x80}, {0x43,0x80,0x80}}, \
+		.port_ops	= &ich_port_ops, \
+		.host_flags	= IDE_HFLAGS_PIIX, \
+		.pio_mask	= ATA_PIO4, \
+		.swdma_mask	= ATA_SWDMA2_ONLY, \
+		.mwdma_mask	= ATA_MWDMA12_ONLY, \
+		.udma_mask	= udma, \
+	}
+
+static const struct ide_port_info piix_pci_info[] __devinitdata = {
+	/* 0: MPIIX */
+	{	/*
+		 * MPIIX actually has only a single IDE channel mapped to
+		 * the primary or secondary ports depending on the value
+		 * of the bit 14 of the IDETIM register at offset 0x6c
+		 */
+		.name		= DRV_NAME,
+		.enablebits	= {{0x6d,0xc0,0x80}, {0x6d,0xc0,0xc0}},
+		.host_flags	= IDE_HFLAG_ISA_PORTS | IDE_HFLAG_NO_DMA |
+				  IDE_HFLAGS_PIIX,
+		.pio_mask	= ATA_PIO4,
+		/* This is a painful system best to let it self tune for now */
+	},
+	/* 1: PIIXa/PIIXb/PIIX3 */
+	DECLARE_PIIX_DEV(0x00), /* no udma */
+	/* 2: PIIX4 */
+	DECLARE_PIIX_DEV(ATA_UDMA2),
+	/* 3: ICH0 */
+	DECLARE_ICH_DEV(ATA_UDMA2),
+	/* 4: ICH */
+	DECLARE_ICH_DEV(ATA_UDMA4),
+	/* 5: PIIX4 */
+	DECLARE_PIIX_DEV(ATA_UDMA4),
+	/* 6: ICH[2-7]/ICH[2-3]M/C-ICH/ICH5-SATA/ESB2/ICH8M */
+	DECLARE_ICH_DEV(ATA_UDMA5),
+};
+
+/**
+ *	piix_init_one	-	called when a PIIX is found
+ *	@dev: the piix device
+ *	@id: the matching pci id
+ *
+ *	Called when the PCI registration layer (or the IDE initialization)
+ *	finds a device matching our IDE device tables.
+ */
+ 
+static int __devinit piix_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	return ide_pci_init_one(dev, &piix_pci_info[id->driver_data], NULL);
+}
+
+/**
+ *	piix_check_450nx	-	Check for problem 450NX setup
+ *	
+ *	Check for the present of 450NX errata #19 and errata #25. If
+ *	they are found, disable use of DMA IDE
+ */
+
+static void __devinit piix_check_450nx(void)
+{
+	struct pci_dev *pdev = NULL;
+	u16 cfg;
+	while((pdev=pci_get_device(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454NX, pdev))!=NULL)
+	{
+		/* Look for 450NX PXB. Check for problem configurations
+		   A PCI quirk checks bit 6 already */
+		pci_read_config_word(pdev, 0x41, &cfg);
+		/* Only on the original revision: IDE DMA can hang */
+		if (pdev->revision == 0x00)
+			no_piix_dma = 1;
+		/* On all revisions below 5 PXB bus lock must be disabled for IDE */
+		else if (cfg & (1<<14) && pdev->revision < 5)
+			no_piix_dma = 2;
+	}
+	if(no_piix_dma)
+		printk(KERN_WARNING DRV_NAME ": 450NX errata present, disabling IDE DMA.\n");
+	if(no_piix_dma == 2)
+		printk(KERN_WARNING DRV_NAME ": A BIOS update may resolve this.\n");
+}		
+
+static const struct pci_device_id piix_pci_tbl[] = {
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_0),  1 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371FB_1),  1 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371MX),    0 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371SB_1),  1 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82371AB),    2 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AB_1),  3 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82443MX_1),  2 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801AA_1),  4 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82372FB_1),  5 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82451NX),    2 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_9),  6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801BA_8),  6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_10), 6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801CA_11), 6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_11), 6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_11), 6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801E_11),  6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_10), 6 },
+#ifdef CONFIG_BLK_DEV_IDE_SATA
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801EB_1),  6 },
+#endif
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB_2),      6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH6_19),    6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH7_21),    6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_82801DB_1),  6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ESB2_18),    6 },
+	{ PCI_VDEVICE(INTEL, PCI_DEVICE_ID_INTEL_ICH8_6),     6 },
+	{ 0, },
+};
+MODULE_DEVICE_TABLE(pci, piix_pci_tbl);
+
+static struct pci_driver piix_pci_driver = {
+	.name		= "PIIX_IDE",
+	.id_table	= piix_pci_tbl,
+	.probe		= piix_init_one,
+	.remove		= ide_pci_remove,
+	.suspend	= ide_pci_suspend,
+	.resume		= ide_pci_resume,
+};
+
+static int __init piix_ide_init(void)
+{
+	piix_check_450nx();
+	return ide_pci_register_driver(&piix_pci_driver);
+}
+
+static void __exit piix_ide_exit(void)
+{
+	pci_unregister_driver(&piix_pci_driver);
+}
+
+module_init(piix_ide_init);
+module_exit(piix_ide_exit);
+
+MODULE_AUTHOR("Andre Hedrick, Andrzej Krzysztofowicz");
+MODULE_DESCRIPTION("PCI driver module for Intel PIIX IDE");
+MODULE_LICENSE("GPL");