ide: remove useless subdirs from drivers/ide/

Suggested-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

1 files changed, 0 insertions, 470 deletions

diff --git a/drivers/ide/pci/serverworks.c b/drivers/ide/pci/serverworks.c
deleted file mode 100644
index 437bc919daf..00000000000
--- a/drivers/ide/pci/serverworks.c
+++ /dev/null
@@ -1,470 +0,0 @@
-/*
- * Copyright (C) 1998-2000 Michel Aubry
- * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
- * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
- * Copyright (C)      2007 Bartlomiej Zolnierkiewicz
- * Portions copyright (c) 2001 Sun Microsystems
- *
- *
- * RCC/ServerWorks IDE driver for Linux
- *
- *   OSB4: `Open South Bridge' IDE Interface (fn 1)
- *         supports UDMA mode 2 (33 MB/s)
- *
- *   CSB5: `Champion South Bridge' IDE Interface (fn 1)
- *         all revisions support UDMA mode 4 (66 MB/s)
- *         revision A2.0 and up support UDMA mode 5 (100 MB/s)
- *
- *         *** The CSB5 does not provide ANY register ***
- *         *** to detect 80-conductor cable presence. ***
- *
- *   CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
- *
- *   HT1000: AKA BCM5785 - Hypertransport Southbridge for Opteron systems. IDE
- *   controller same as the CSB6. Single channel ATA100 only.
- *
- * Documentation:
- *	Available under NDA only. Errata info very hard to get.
- *
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-
-#include <asm/io.h>
-
-#define DRV_NAME "serverworks"
-
-#define SVWKS_CSB5_REVISION_NEW	0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
-#define SVWKS_CSB6_REVISION	0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
-
-/* Seagate Barracuda ATA IV Family drives in UDMA mode 5
- * can overrun their FIFOs when used with the CSB5 */
-static const char *svwks_bad_ata100[] = {
-	"ST320011A",
-	"ST340016A",
-	"ST360021A",
-	"ST380021A",
-	NULL
-};
-
-static struct pci_dev *isa_dev;
-
-static int check_in_drive_lists (ide_drive_t *drive, const char **list)
-{
-	char *m = (char *)&drive->id[ATA_ID_PROD];
-
-	while (*list)
-		if (!strcmp(*list++, m))
-			return 1;
-	return 0;
-}
-
-static u8 svwks_udma_filter(ide_drive_t *drive)
-{
-	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
-	u8 mask = 0;
-
-	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
-		return 0x1f;
-	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
-		u32 reg = 0;
-		if (isa_dev)
-			pci_read_config_dword(isa_dev, 0x64, &reg);
-			
-		/*
-		 *	Don't enable UDMA on disk devices for the moment
-		 */
-		if(drive->media == ide_disk)
-			return 0;
-		/* Check the OSB4 DMA33 enable bit */
-		return ((reg & 0x00004000) == 0x00004000) ? 0x07 : 0;
-	} else if (dev->revision < SVWKS_CSB5_REVISION_NEW) {
-		return 0x07;
-	} else if (dev->revision >= SVWKS_CSB5_REVISION_NEW) {
-		u8 btr = 0, mode;
-		pci_read_config_byte(dev, 0x5A, &btr);
-		mode = btr & 0x3;
-
-		/* If someone decides to do UDMA133 on CSB5 the same
-		   issue will bite so be inclusive */
-		if (mode > 2 && check_in_drive_lists(drive, svwks_bad_ata100))
-			mode = 2;
-
-		switch(mode) {
-		case 3:	 mask = 0x3f; break;
-		case 2:	 mask = 0x1f; break;
-		case 1:	 mask = 0x07; break;
-		default: mask = 0x00; break;
-		}
-	}
-	if (((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
-	     (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) &&
-	    (!(PCI_FUNC(dev->devfn) & 1)))
-		mask = 0x1f;
-
-	return mask;
-}
-
-static u8 svwks_csb_check (struct pci_dev *dev)
-{
-	switch (dev->device) {
-		case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
-		case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
-		case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
-		case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
-			return 1;
-		default:
-			break;
-	}
-	return 0;
-}
-
-static void svwks_set_pio_mode(ide_drive_t *drive, const u8 pio)
-{
-	static const u8 pio_modes[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
-	static const u8 drive_pci[] = { 0x41, 0x40, 0x43, 0x42 };
-
-	struct pci_dev *dev = to_pci_dev(drive->hwif->dev);
-
-	pci_write_config_byte(dev, drive_pci[drive->dn], pio_modes[pio]);
-
-	if (svwks_csb_check(dev)) {
-		u16 csb_pio = 0;
-
-		pci_read_config_word(dev, 0x4a, &csb_pio);
-
-		csb_pio &= ~(0x0f << (4 * drive->dn));
-		csb_pio |= (pio << (4 * drive->dn));
-
-		pci_write_config_word(dev, 0x4a, csb_pio);
-	}
-}
-
-static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
-{
-	static const u8 udma_modes[]		= { 0x00, 0x01, 0x02, 0x03, 0x04, 0x05 };
-	static const u8 dma_modes[]		= { 0x77, 0x21, 0x20 };
-	static const u8 drive_pci2[]		= { 0x45, 0x44, 0x47, 0x46 };
-
-	ide_hwif_t *hwif	= HWIF(drive);
-	struct pci_dev *dev	= to_pci_dev(hwif->dev);
-	u8 unit			= drive->dn & 1;
-
-	u8 ultra_enable	 = 0, ultra_timing = 0, dma_timing = 0;
-
-	pci_read_config_byte(dev, (0x56|hwif->channel), &ultra_timing);
-	pci_read_config_byte(dev, 0x54, &ultra_enable);
-
-	ultra_timing	&= ~(0x0F << (4*unit));
-	ultra_enable	&= ~(0x01 << drive->dn);
-
-	if (speed >= XFER_UDMA_0) {
-		dma_timing   |= dma_modes[2];
-		ultra_timing |= (udma_modes[speed - XFER_UDMA_0] << (4 * unit));
-		ultra_enable |= (0x01 << drive->dn);
-	} else if (speed >= XFER_MW_DMA_0)
-		dma_timing   |= dma_modes[speed - XFER_MW_DMA_0];
-
-	pci_write_config_byte(dev, drive_pci2[drive->dn], dma_timing);
-	pci_write_config_byte(dev, (0x56|hwif->channel), ultra_timing);
-	pci_write_config_byte(dev, 0x54, ultra_enable);
-}
-
-static unsigned int init_chipset_svwks(struct pci_dev *dev)
-{
-	unsigned int reg;
-	u8 btr;
-
-	/* force Master Latency Timer value to 64 PCICLKs */
-	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x40);
-
-	/* OSB4 : South Bridge and IDE */
-	if (dev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
-		isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
-			  PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
-		if (isa_dev) {
-			pci_read_config_dword(isa_dev, 0x64, &reg);
-			reg &= ~0x00002000; /* disable 600ns interrupt mask */
-			if(!(reg & 0x00004000))
-				printk(KERN_DEBUG DRV_NAME " %s: UDMA not BIOS "
-					"enabled.\n", pci_name(dev));
-			reg |=  0x00004000; /* enable UDMA/33 support */
-			pci_write_config_dword(isa_dev, 0x64, reg);
-		}
-	}
-
-	/* setup CSB5/CSB6 : South Bridge and IDE option RAID */
-	else if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
-		 (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
-		 (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
-
-		/* Third Channel Test */
-		if (!(PCI_FUNC(dev->devfn) & 1)) {
-			struct pci_dev * findev = NULL;
-			u32 reg4c = 0;
-			findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
-				PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
-			if (findev) {
-				pci_read_config_dword(findev, 0x4C, &reg4c);
-				reg4c &= ~0x000007FF;
-				reg4c |=  0x00000040;
-				reg4c |=  0x00000020;
-				pci_write_config_dword(findev, 0x4C, reg4c);
-				pci_dev_put(findev);
-			}
-			outb_p(0x06, 0x0c00);
-			dev->irq = inb_p(0x0c01);
-		} else {
-			struct pci_dev * findev = NULL;
-			u8 reg41 = 0;
-
-			findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
-					PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
-			if (findev) {
-				pci_read_config_byte(findev, 0x41, &reg41);
-				reg41 &= ~0x40;
-				pci_write_config_byte(findev, 0x41, reg41);
-				pci_dev_put(findev);
-			}
-			/*
-			 * This is a device pin issue on CSB6.
-			 * Since there will be a future raid mode,
-			 * early versions of the chipset require the
-			 * interrupt pin to be set, and it is a compatibility
-			 * mode issue.
-			 */
-			if ((dev->class >> 8) == PCI_CLASS_STORAGE_IDE)
-				dev->irq = 0;
-		}
-//		pci_read_config_dword(dev, 0x40, &pioreg)
-//		pci_write_config_dword(dev, 0x40, 0x99999999);
-//		pci_read_config_dword(dev, 0x44, &dmareg);
-//		pci_write_config_dword(dev, 0x44, 0xFFFFFFFF);
-		/* setup the UDMA Control register
-		 *
-		 * 1. clear bit 6 to enable DMA
-		 * 2. enable DMA modes with bits 0-1
-		 * 	00 : legacy
-		 * 	01 : udma2
-		 * 	10 : udma2/udma4
-		 * 	11 : udma2/udma4/udma5
-		 */
-		pci_read_config_byte(dev, 0x5A, &btr);
-		btr &= ~0x40;
-		if (!(PCI_FUNC(dev->devfn) & 1))
-			btr |= 0x2;
-		else
-			btr |= (dev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
-		pci_write_config_byte(dev, 0x5A, btr);
-	}
-	/* Setup HT1000 SouthBridge Controller - Single Channel Only */
-	else if (dev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE) {
-		pci_read_config_byte(dev, 0x5A, &btr);
-		btr &= ~0x40;
-		btr |= 0x3;
-		pci_write_config_byte(dev, 0x5A, btr);
-	}
-
-	return dev->irq;
-}
-
-static u8 ata66_svwks_svwks(ide_hwif_t *hwif)
-{
-	return ATA_CBL_PATA80;
-}
-
-/* On Dell PowerEdge servers with a CSB5/CSB6, the top two bits
- * of the subsystem device ID indicate presence of an 80-pin cable.
- * Bit 15 clear = secondary IDE channel does not have 80-pin cable.
- * Bit 15 set   = secondary IDE channel has 80-pin cable.
- * Bit 14 clear = primary IDE channel does not have 80-pin cable.
- * Bit 14 set   = primary IDE channel has 80-pin cable.
- */
-static u8 ata66_svwks_dell(ide_hwif_t *hwif)
-{
-	struct pci_dev *dev = to_pci_dev(hwif->dev);
-
-	if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL &&
-	    dev->vendor	== PCI_VENDOR_ID_SERVERWORKS &&
-	    (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE ||
-	     dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE))
-		return ((1 << (hwif->channel + 14)) &
-			dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
-	return ATA_CBL_PATA40;
-}
-
-/* Sun Cobalt Alpine hardware avoids the 80-pin cable
- * detect issue by attaching the drives directly to the board.
- * This check follows the Dell precedent (how scary is that?!)
- *
- * WARNING: this only works on Alpine hardware!
- */
-static u8 ata66_svwks_cobalt(ide_hwif_t *hwif)
-{
-	struct pci_dev *dev = to_pci_dev(hwif->dev);
-
-	if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN &&
-	    dev->vendor	== PCI_VENDOR_ID_SERVERWORKS &&
-	    dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
-		return ((1 << (hwif->channel + 14)) &
-			dev->subsystem_device) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
-	return ATA_CBL_PATA40;
-}
-
-static u8 svwks_cable_detect(ide_hwif_t *hwif)
-{
-	struct pci_dev *dev = to_pci_dev(hwif->dev);
-
-	/* Server Works */
-	if (dev->subsystem_vendor == PCI_VENDOR_ID_SERVERWORKS)
-		return ata66_svwks_svwks (hwif);
-	
-	/* Dell PowerEdge */
-	if (dev->subsystem_vendor == PCI_VENDOR_ID_DELL)
-		return ata66_svwks_dell (hwif);
-
-	/* Cobalt Alpine */
-	if (dev->subsystem_vendor == PCI_VENDOR_ID_SUN)
-		return ata66_svwks_cobalt (hwif);
-
-	/* Per Specified Design by OEM, and ASIC Architect */
-	if ((dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
-	    (dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2))
-		return ATA_CBL_PATA80;
-
-	return ATA_CBL_PATA40;
-}
-
-static const struct ide_port_ops osb4_port_ops = {
-	.set_pio_mode		= svwks_set_pio_mode,
-	.set_dma_mode		= svwks_set_dma_mode,
-	.udma_filter		= svwks_udma_filter,
-};
-
-static const struct ide_port_ops svwks_port_ops = {
-	.set_pio_mode		= svwks_set_pio_mode,
-	.set_dma_mode		= svwks_set_dma_mode,
-	.udma_filter		= svwks_udma_filter,
-	.cable_detect		= svwks_cable_detect,
-};
-
-#define IDE_HFLAGS_SVWKS IDE_HFLAG_LEGACY_IRQS
-
-static const struct ide_port_info serverworks_chipsets[] __devinitdata = {
-	{	/* 0: OSB4 */
-		.name		= DRV_NAME,
-		.init_chipset	= init_chipset_svwks,
-		.port_ops	= &osb4_port_ops,
-		.host_flags	= IDE_HFLAGS_SVWKS,
-		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
-		.udma_mask	= 0x00, /* UDMA is problematic on OSB4 */
-	},
-	{	/* 1: CSB5 */
-		.name		= DRV_NAME,
-		.init_chipset	= init_chipset_svwks,
-		.port_ops	= &svwks_port_ops,
-		.host_flags	= IDE_HFLAGS_SVWKS,
-		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
-		.udma_mask	= ATA_UDMA5,
-	},
-	{	/* 2: CSB6 */
-		.name		= DRV_NAME,
-		.init_chipset	= init_chipset_svwks,
-		.port_ops	= &svwks_port_ops,
-		.host_flags	= IDE_HFLAGS_SVWKS,
-		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
-		.udma_mask	= ATA_UDMA5,
-	},
-	{	/* 3: CSB6-2 */
-		.name		= DRV_NAME,
-		.init_chipset	= init_chipset_svwks,
-		.port_ops	= &svwks_port_ops,
-		.host_flags	= IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
-		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
-		.udma_mask	= ATA_UDMA5,
-	},
-	{	/* 4: HT1000 */
-		.name		= DRV_NAME,
-		.init_chipset	= init_chipset_svwks,
-		.port_ops	= &svwks_port_ops,
-		.host_flags	= IDE_HFLAGS_SVWKS | IDE_HFLAG_SINGLE,
-		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
-		.udma_mask	= ATA_UDMA5,
-	}
-};
-
-/**
- *	svwks_init_one	-	called when a OSB/CSB is found
- *	@dev: the svwks device
- *	@id: the matching pci id
- *
- *	Called when the PCI registration layer (or the IDE initialization)
- *	finds a device matching our IDE device tables.
- */
- 
-static int __devinit svwks_init_one(struct pci_dev *dev, const struct pci_device_id *id)
-{
-	struct ide_port_info d;
-	u8 idx = id->driver_data;
-
-	d = serverworks_chipsets[idx];
-
-	if (idx == 1)
-		d.host_flags |= IDE_HFLAG_CLEAR_SIMPLEX;
-	else if (idx == 2 || idx == 3) {
-		if ((PCI_FUNC(dev->devfn) & 1) == 0) {
-			if (pci_resource_start(dev, 0) != 0x01f1)
-				d.host_flags |= IDE_HFLAG_NON_BOOTABLE;
-			d.host_flags |= IDE_HFLAG_SINGLE;
-		} else
-			d.host_flags &= ~IDE_HFLAG_SINGLE;
-	}
-
-	return ide_pci_init_one(dev, &d, NULL);
-}
-
-static const struct pci_device_id svwks_pci_tbl[] = {
-	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE),   0 },
-	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE),   1 },
-	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE),   2 },
-	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2),  3 },
-	{ PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 4 },
-	{ 0, },
-};
-MODULE_DEVICE_TABLE(pci, svwks_pci_tbl);
-
-static struct pci_driver svwks_pci_driver = {
-	.name		= "Serverworks_IDE",
-	.id_table	= svwks_pci_tbl,
-	.probe		= svwks_init_one,
-	.remove		= ide_pci_remove,
-	.suspend	= ide_pci_suspend,
-	.resume		= ide_pci_resume,
-};
-
-static int __init svwks_ide_init(void)
-{
-	return ide_pci_register_driver(&svwks_pci_driver);
-}
-
-static void __exit svwks_ide_exit(void)
-{
-	pci_unregister_driver(&svwks_pci_driver);
-}
-
-module_init(svwks_ide_init);
-module_exit(svwks_ide_exit);
-
-MODULE_AUTHOR("Michael Aubry. Andrzej Krzysztofowicz, Andre Hedrick");
-MODULE_DESCRIPTION("PCI driver module for Serverworks OSB4/CSB5/CSB6 IDE");
-MODULE_LICENSE("GPL");