ide: remove useless subdirs from drivers/ide/

Suggested-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

1 files changed, 0 insertions, 192 deletions

diff --git a/drivers/ide/pci/delkin_cb.c b/drivers/ide/pci/delkin_cb.c
deleted file mode 100644
index 8f1b2d9f051..00000000000
--- a/drivers/ide/pci/delkin_cb.c
+++ /dev/null
@@ -1,192 +0,0 @@
-/*
- *  Created 20 Oct 2004 by Mark Lord
- *
- *  Basic support for Delkin/ASKA/Workbit Cardbus CompactFlash adapter
- *
- *  Modeled after the 16-bit PCMCIA driver: ide-cs.c
- *
- *  This is slightly peculiar, in that it is a PCI driver,
- *  but is NOT an IDE PCI driver -- the IDE layer does not directly
- *  support hot insertion/removal of PCI interfaces, so this driver
- *  is unable to use the IDE PCI interfaces.  Instead, it uses the
- *  same interfaces as the ide-cs (PCMCIA) driver uses.
- *  On the plus side, the driver is also smaller/simpler this way.
- *
- *  This file is subject to the terms and conditions of the GNU General Public
- *  License.  See the file COPYING in the main directory of this archive for
- *  more details.
- */
-
-#include <linux/types.h>
-#include <linux/module.h>
-#include <linux/ide.h>
-#include <linux/init.h>
-#include <linux/pci.h>
-
-#include <asm/io.h>
-
-/*
- * No chip documentation has yet been found,
- * so these configuration values were pulled from
- * a running Win98 system using "debug".
- * This gives around 3MByte/second read performance,
- * which is about 2/3 of what the chip is capable of.
- *
- * There is also a 4KByte mmio region on the card,
- * but its purpose has yet to be reverse-engineered.
- */
-static const u8 setup[] = {
-	0x00, 0x05, 0xbe, 0x01, 0x20, 0x8f, 0x00, 0x00,
-	0xa4, 0x1f, 0xb3, 0x1b, 0x00, 0x00, 0x00, 0x80,
-	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
-	0x00, 0x00, 0x00, 0x00, 0xa4, 0x83, 0x02, 0x13,
-};
-
-static const struct ide_port_ops delkin_cb_port_ops = {
-	.quirkproc		= ide_undecoded_slave,
-};
-
-static unsigned int delkin_cb_init_chipset(struct pci_dev *dev)
-{
-	unsigned long base = pci_resource_start(dev, 0);
-	int i;
-
-	outb(0x02, base + 0x1e);	/* set nIEN to block interrupts */
-	inb(base + 0x17);		/* read status to clear interrupts */
-
-	for (i = 0; i < sizeof(setup); ++i) {
-		if (setup[i])
-			outb(setup[i], base + i);
-	}
-
-	return 0;
-}
-
-static const struct ide_port_info delkin_cb_port_info = {
-	.port_ops		= &delkin_cb_port_ops,
-	.host_flags		= IDE_HFLAG_IO_32BIT | IDE_HFLAG_UNMASK_IRQS |
-				  IDE_HFLAG_NO_DMA,
-	.init_chipset		= delkin_cb_init_chipset,
-};
-
-static int __devinit
-delkin_cb_probe (struct pci_dev *dev, const struct pci_device_id *id)
-{
-	struct ide_host *host;
-	unsigned long base;
-	int rc;
-	hw_regs_t hw, *hws[] = { &hw, NULL, NULL, NULL };
-
-	rc = pci_enable_device(dev);
-	if (rc) {
-		printk(KERN_ERR "delkin_cb: pci_enable_device failed (%d)\n", rc);
-		return rc;
-	}
-	rc = pci_request_regions(dev, "delkin_cb");
-	if (rc) {
-		printk(KERN_ERR "delkin_cb: pci_request_regions failed (%d)\n", rc);
-		pci_disable_device(dev);
-		return rc;
-	}
-	base = pci_resource_start(dev, 0);
-
-	delkin_cb_init_chipset(dev);
-
-	memset(&hw, 0, sizeof(hw));
-	ide_std_init_ports(&hw, base + 0x10, base + 0x1e);
-	hw.irq = dev->irq;
-	hw.dev = &dev->dev;
-	hw.chipset = ide_pci;		/* this enables IRQ sharing */
-
-	rc = ide_host_add(&delkin_cb_port_info, hws, &host);
-	if (rc)
-		goto out_disable;
-
-	pci_set_drvdata(dev, host);
-
-	return 0;
-
-out_disable:
-	pci_release_regions(dev);
-	pci_disable_device(dev);
-	return rc;
-}
-
-static void
-delkin_cb_remove (struct pci_dev *dev)
-{
-	struct ide_host *host = pci_get_drvdata(dev);
-
-	ide_host_remove(host);
-
-	pci_release_regions(dev);
-	pci_disable_device(dev);
-}
-
-#ifdef CONFIG_PM
-static int delkin_cb_suspend(struct pci_dev *dev, pm_message_t state)
-{
-	pci_save_state(dev);
-	pci_disable_device(dev);
-	pci_set_power_state(dev, pci_choose_state(dev, state));
-
-	return 0;
-}
-
-static int delkin_cb_resume(struct pci_dev *dev)
-{
-	struct ide_host *host = pci_get_drvdata(dev);
-	int rc;
-
-	pci_set_power_state(dev, PCI_D0);
-
-	rc = pci_enable_device(dev);
-	if (rc)
-		return rc;
-
-	pci_restore_state(dev);
-	pci_set_master(dev);
-
-	if (host->init_chipset)
-		host->init_chipset(dev);
-
-	return 0;
-}
-#else
-#define delkin_cb_suspend NULL
-#define delkin_cb_resume NULL
-#endif
-
-static struct pci_device_id delkin_cb_pci_tbl[] __devinitdata = {
-	{ 0x1145, 0xf021, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
-	{ 0x1145, 0xf024, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
-	{ 0, },
-};
-MODULE_DEVICE_TABLE(pci, delkin_cb_pci_tbl);
-
-static struct pci_driver delkin_cb_pci_driver = {
-	.name		= "Delkin-ASKA-Workbit Cardbus IDE",
-	.id_table	= delkin_cb_pci_tbl,
-	.probe		= delkin_cb_probe,
-	.remove		= delkin_cb_remove,
-	.suspend	= delkin_cb_suspend,
-	.resume		= delkin_cb_resume,
-};
-
-static int __init delkin_cb_init(void)
-{
-	return pci_register_driver(&delkin_cb_pci_driver);
-}
-
-static void __exit delkin_cb_exit(void)
-{
-	pci_unregister_driver(&delkin_cb_pci_driver);
-}
-
-module_init(delkin_cb_init);
-module_exit(delkin_cb_exit);
-
-MODULE_AUTHOR("Mark Lord");
-MODULE_DESCRIPTION("Basic support for Delkin/ASKA/Workbit Cardbus IDE");
-MODULE_LICENSE("GPL");
-