Merge branch 'master' of master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6

Conflicts:

	Documentation/powerpc/booting-without-of.txt
	drivers/atm/Makefile
	drivers/net/fs_enet/fs_enet-main.c
	drivers/pci/pci-acpi.c
	net/8021q/vlan.c
	net/iucv/iucv.c

12 files changed, 56 insertions, 864 deletions

diff --git a/drivers/ide/legacy/ali14xx.c b/drivers/ide/legacy/ali14xx.c
index 90c65cf9744..4ec19737f3c 100644
--- a/drivers/ide/legacy/ali14xx.c
+++ b/drivers/ide/legacy/ali14xx.c
@@ -116,11 +116,12 @@ static void ali14xx_set_pio_mode(ide_drive_t *drive, const u8 pio)
 	int time1, time2;
 	u8 param1, param2, param3, param4;
 	unsigned long flags;
-	int bus_speed = ide_vlb_clk ? ide_vlb_clk : system_bus_clock();
+	int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
+	struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
 
 	/* calculate timing, according to PIO mode */
 	time1 = ide_pio_cycle_time(drive, pio);
-	time2 = ide_pio_timings[pio].active_time;
+	time2 = t->active;
 	param3 = param1 = (time2 * bus_speed + 999) / 1000;
 	param4 = param2 = (time1 * bus_speed + 999) / 1000 - param1;
 	if (pio < 3) {
diff --git a/drivers/ide/legacy/buddha.c b/drivers/ide/legacy/buddha.c
index 9a1d27ef3f8..0497e7f85b0 100644
--- a/drivers/ide/legacy/buddha.c
+++ b/drivers/ide/legacy/buddha.c
@@ -227,7 +227,6 @@ fail_base2:
 			if (hwif) {
 				u8 index = hwif->index;
 
-				ide_init_port_data(hwif, index);
 				ide_init_port_hw(hwif, &hw);
 
 				idx[i] = index;
diff --git a/drivers/ide/legacy/falconide.c b/drivers/ide/legacy/falconide.c
index af11028b479..129a812bb57 100644
--- a/drivers/ide/legacy/falconide.c
+++ b/drivers/ide/legacy/falconide.c
@@ -111,7 +111,6 @@ static int __init falconide_init(void)
 		u8 index = hwif->index;
 		u8 idx[4] = { index, 0xff, 0xff, 0xff };
 
-		ide_init_port_data(hwif, index);
 		ide_init_port_hw(hwif, &hw);
 
 		/* Atari has a byte-swapped IDE interface */
diff --git a/drivers/ide/legacy/gayle.c b/drivers/ide/legacy/gayle.c
index fed7d812761..7e74b20202d 100644
--- a/drivers/ide/legacy/gayle.c
+++ b/drivers/ide/legacy/gayle.c
@@ -64,9 +64,7 @@
 #define GAYLE_HAS_CONTROL_REG	(!ide_doubler)
 #define GAYLE_IDEREG_SIZE	(ide_doubler ? 0x1000 : 0x2000)
 
-int ide_doubler = 0;	/* support IDE doublers? */
-EXPORT_SYMBOL_GPL(ide_doubler);
-
+static int ide_doubler;
 module_param_named(doubler, ide_doubler, bool, 0);
 MODULE_PARM_DESC(doubler, "enable support for IDE doublers");
 #endif /* CONFIG_BLK_DEV_IDEDOUBLER */
@@ -187,7 +185,6 @@ found:
 	if (hwif) {
 	    u8 index = hwif->index;
 
-	    ide_init_port_data(hwif, index);
 	    ide_init_port_hw(hwif, &hw);
 
 	    idx[i] = index;
diff --git a/drivers/ide/legacy/hd.c b/drivers/ide/legacy/hd.c
deleted file mode 100644
index abdedf56643..00000000000
--- a/drivers/ide/legacy/hd.c
+++ /dev/null
@@ -1,815 +0,0 @@
-/*
- *  Copyright (C) 1991, 1992  Linus Torvalds
- *
- * This is the low-level hd interrupt support. It traverses the
- * request-list, using interrupts to jump between functions. As
- * all the functions are called within interrupts, we may not
- * sleep. Special care is recommended.
- *
- *  modified by Drew Eckhardt to check nr of hd's from the CMOS.
- *
- *  Thanks to Branko Lankester, lankeste@fwi.uva.nl, who found a bug
- *  in the early extended-partition checks and added DM partitions
- *
- *  IRQ-unmask, drive-id, multiple-mode, support for ">16 heads",
- *  and general streamlining by Mark Lord.
- *
- *  Removed 99% of above. Use Mark's ide driver for those options.
- *  This is now a lightweight ST-506 driver. (Paul Gortmaker)
- *
- *  Modified 1995 Russell King for ARM processor.
- *
- *  Bugfix: max_sectors must be <= 255 or the wheels tend to come
- *  off in a hurry once you queue things up - Paul G. 02/2001
- */
-
-/* Uncomment the following if you want verbose error reports. */
-/* #define VERBOSE_ERRORS */
-
-#include <linux/blkdev.h>
-#include <linux/errno.h>
-#include <linux/signal.h>
-#include <linux/interrupt.h>
-#include <linux/timer.h>
-#include <linux/fs.h>
-#include <linux/kernel.h>
-#include <linux/genhd.h>
-#include <linux/slab.h>
-#include <linux/string.h>
-#include <linux/ioport.h>
-#include <linux/mc146818rtc.h> /* CMOS defines */
-#include <linux/init.h>
-#include <linux/blkpg.h>
-#include <linux/hdreg.h>
-
-#define REALLY_SLOW_IO
-#include <asm/system.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-
-#ifdef __arm__
-#undef  HD_IRQ
-#endif
-#include <asm/irq.h>
-#ifdef __arm__
-#define HD_IRQ IRQ_HARDDISK
-#endif
-
-/* Hd controller regster ports */
-
-#define HD_DATA		0x1f0		/* _CTL when writing */
-#define HD_ERROR	0x1f1		/* see err-bits */
-#define HD_NSECTOR	0x1f2		/* nr of sectors to read/write */
-#define HD_SECTOR	0x1f3		/* starting sector */
-#define HD_LCYL		0x1f4		/* starting cylinder */
-#define HD_HCYL		0x1f5		/* high byte of starting cyl */
-#define HD_CURRENT	0x1f6		/* 101dhhhh , d=drive, hhhh=head */
-#define HD_STATUS	0x1f7		/* see status-bits */
-#define HD_FEATURE	HD_ERROR	/* same io address, read=error, write=feature */
-#define HD_PRECOMP	HD_FEATURE	/* obsolete use of this port - predates IDE */
-#define HD_COMMAND	HD_STATUS	/* same io address, read=status, write=cmd */
-
-#define HD_CMD		0x3f6		/* used for resets */
-#define HD_ALTSTATUS	0x3f6		/* same as HD_STATUS but doesn't clear irq */
-
-/* Bits of HD_STATUS */
-#define ERR_STAT		0x01
-#define INDEX_STAT		0x02
-#define ECC_STAT		0x04	/* Corrected error */
-#define DRQ_STAT		0x08
-#define SEEK_STAT		0x10
-#define SERVICE_STAT		SEEK_STAT
-#define WRERR_STAT		0x20
-#define READY_STAT		0x40
-#define BUSY_STAT		0x80
-
-/* Bits for HD_ERROR */
-#define MARK_ERR		0x01	/* Bad address mark */
-#define TRK0_ERR		0x02	/* couldn't find track 0 */
-#define ABRT_ERR		0x04	/* Command aborted */
-#define MCR_ERR			0x08	/* media change request */
-#define ID_ERR			0x10	/* ID field not found */
-#define MC_ERR			0x20	/* media changed */
-#define ECC_ERR			0x40	/* Uncorrectable ECC error */
-#define BBD_ERR			0x80	/* pre-EIDE meaning:  block marked bad */
-#define ICRC_ERR		0x80	/* new meaning:  CRC error during transfer */
-
-static DEFINE_SPINLOCK(hd_lock);
-static struct request_queue *hd_queue;
-
-#define MAJOR_NR HD_MAJOR
-#define QUEUE (hd_queue)
-#define CURRENT elv_next_request(hd_queue)
-
-#define TIMEOUT_VALUE	(6*HZ)
-#define	HD_DELAY	0
-
-#define MAX_ERRORS     16	/* Max read/write errors/sector */
-#define RESET_FREQ      8	/* Reset controller every 8th retry */
-#define RECAL_FREQ      4	/* Recalibrate every 4th retry */
-#define MAX_HD		2
-
-#define STAT_OK		(READY_STAT|SEEK_STAT)
-#define OK_STATUS(s)	(((s)&(STAT_OK|(BUSY_STAT|WRERR_STAT|ERR_STAT)))==STAT_OK)
-
-static void recal_intr(void);
-static void bad_rw_intr(void);
-
-static int reset;
-static int hd_error;
-
-/*
- *  This struct defines the HD's and their types.
- */
-struct hd_i_struct {
-	unsigned int head, sect, cyl, wpcom, lzone, ctl;
-	int unit;
-	int recalibrate;
-	int special_op;
-};
-
-#ifdef HD_TYPE
-static struct hd_i_struct hd_info[] = { HD_TYPE };
-static int NR_HD = ARRAY_SIZE(hd_info);
-#else
-static struct hd_i_struct hd_info[MAX_HD];
-static int NR_HD;
-#endif
-
-static struct gendisk *hd_gendisk[MAX_HD];
-
-static struct timer_list device_timer;
-
-#define TIMEOUT_VALUE (6*HZ)
-
-#define SET_TIMER							\
-	do {								\
-		mod_timer(&device_timer, jiffies + TIMEOUT_VALUE);	\
-	} while (0)
-
-static void (*do_hd)(void) = NULL;
-#define SET_HANDLER(x) \
-if ((do_hd = (x)) != NULL) \
-	SET_TIMER; \
-else \
-	del_timer(&device_timer);
-
-
-#if (HD_DELAY > 0)
-
-#include <asm/i8253.h>
-
-unsigned long last_req;
-
-unsigned long read_timer(void)
-{
-	unsigned long t, flags;
-	int i;
-
-	spin_lock_irqsave(&i8253_lock, flags);
-	t = jiffies * 11932;
-	outb_p(0, 0x43);
-	i = inb_p(0x40);
-	i |= inb(0x40) << 8;
-	spin_unlock_irqrestore(&i8253_lock, flags);
-	return(t - i);
-}
-#endif
-
-static void __init hd_setup(char *str, int *ints)
-{
-	int hdind = 0;
-
-	if (ints[0] != 3)
-		return;
-	if (hd_info[0].head != 0)
-		hdind = 1;
-	hd_info[hdind].head = ints[2];
-	hd_info[hdind].sect = ints[3];
-	hd_info[hdind].cyl = ints[1];
-	hd_info[hdind].wpcom = 0;
-	hd_info[hdind].lzone = ints[1];
-	hd_info[hdind].ctl = (ints[2] > 8 ? 8 : 0);
-	NR_HD = hdind+1;
-}
-
-static void dump_status(const char *msg, unsigned int stat)
-{
-	char *name = "hd?";
-	if (CURRENT)
-		name = CURRENT->rq_disk->disk_name;
-
-#ifdef VERBOSE_ERRORS
-	printk("%s: %s: status=0x%02x { ", name, msg, stat & 0xff);
-	if (stat & BUSY_STAT)	printk("Busy ");
-	if (stat & READY_STAT)	printk("DriveReady ");
-	if (stat & WRERR_STAT)	printk("WriteFault ");
-	if (stat & SEEK_STAT)	printk("SeekComplete ");
-	if (stat & DRQ_STAT)	printk("DataRequest ");
-	if (stat & ECC_STAT)	printk("CorrectedError ");
-	if (stat & INDEX_STAT)	printk("Index ");
-	if (stat & ERR_STAT)	printk("Error ");
-	printk("}\n");
-	if ((stat & ERR_STAT) == 0) {
-		hd_error = 0;
-	} else {
-		hd_error = inb(HD_ERROR);
-		printk("%s: %s: error=0x%02x { ", name, msg, hd_error & 0xff);
-		if (hd_error & BBD_ERR)		printk("BadSector ");
-		if (hd_error & ECC_ERR)		printk("UncorrectableError ");
-		if (hd_error & ID_ERR)		printk("SectorIdNotFound ");
-		if (hd_error & ABRT_ERR)	printk("DriveStatusError ");
-		if (hd_error & TRK0_ERR)	printk("TrackZeroNotFound ");
-		if (hd_error & MARK_ERR)	printk("AddrMarkNotFound ");
-		printk("}");
-		if (hd_error & (BBD_ERR|ECC_ERR|ID_ERR|MARK_ERR)) {
-			printk(", CHS=%d/%d/%d", (inb(HD_HCYL)<<8) + inb(HD_LCYL),
-				inb(HD_CURRENT) & 0xf, inb(HD_SECTOR));
-			if (CURRENT)
-				printk(", sector=%ld", CURRENT->sector);
-		}
-		printk("\n");
-	}
-#else
-	printk("%s: %s: status=0x%02x.\n", name, msg, stat & 0xff);
-	if ((stat & ERR_STAT) == 0) {
-		hd_error = 0;
-	} else {
-		hd_error = inb(HD_ERROR);
-		printk("%s: %s: error=0x%02x.\n", name, msg, hd_error & 0xff);
-	}
-#endif
-}
-
-static void check_status(void)
-{
-	int i = inb_p(HD_STATUS);
-
-	if (!OK_STATUS(i)) {
-		dump_status("check_status", i);
-		bad_rw_intr();
-	}
-}
-
-static int controller_busy(void)
-{
-	int retries = 100000;
-	unsigned char status;
-
-	do {
-		status = inb_p(HD_STATUS);
-	} while ((status & BUSY_STAT) && --retries);
-	return status;
-}
-
-static int status_ok(void)
-{
-	unsigned char status = inb_p(HD_STATUS);
-
-	if (status & BUSY_STAT)
-		return 1;	/* Ancient, but does it make sense??? */
-	if (status & WRERR_STAT)
-		return 0;
-	if (!(status & READY_STAT))
-		return 0;
-	if (!(status & SEEK_STAT))
-		return 0;
-	return 1;
-}
-
-static int controller_ready(unsigned int drive, unsigned int head)
-{
-	int retry = 100;
-
-	do {
-		if (controller_busy() & BUSY_STAT)
-			return 0;
-		outb_p(0xA0 | (drive<<4) | head, HD_CURRENT);
-		if (status_ok())
-			return 1;
-	} while (--retry);
-	return 0;
-}
-
-static void hd_out(struct hd_i_struct *disk,
-		   unsigned int nsect,
-		   unsigned int sect,
-		   unsigned int head,
-		   unsigned int cyl,
-		   unsigned int cmd,
-		   void (*intr_addr)(void))
-{
-	unsigned short port;
-
-#if (HD_DELAY > 0)
-	while (read_timer() - last_req < HD_DELAY)
-		/* nothing */;
-#endif
-	if (reset)
-		return;
-	if (!controller_ready(disk->unit, head)) {
-		reset = 1;
-		return;
-	}
-	SET_HANDLER(intr_addr);
-	outb_p(disk->ctl, HD_CMD);
-	port = HD_DATA;
-	outb_p(disk->wpcom >> 2, ++port);
-	outb_p(nsect, ++port);
-	outb_p(sect, ++port);
-	outb_p(cyl, ++port);
-	outb_p(cyl >> 8, ++port);
-	outb_p(0xA0 | (disk->unit << 4) | head, ++port);
-	outb_p(cmd, ++port);
-}
-
-static void hd_request (void);
-
-static int drive_busy(void)
-{
-	unsigned int i;
-	unsigned char c;
-
-	for (i = 0; i < 500000 ; i++) {
-		c = inb_p(HD_STATUS);
-		if ((c & (BUSY_STAT | READY_STAT | SEEK_STAT)) == STAT_OK)
-			return 0;
-	}
-	dump_status("reset timed out", c);
-	return 1;
-}
-
-static void reset_controller(void)
-{
-	int	i;
-
-	outb_p(4, HD_CMD);
-	for (i = 0; i < 1000; i++) barrier();
-	outb_p(hd_info[0].ctl & 0x0f, HD_CMD);
-	for (i = 0; i < 1000; i++) barrier();
-	if (drive_busy())
-		printk("hd: controller still busy\n");
-	else if ((hd_error = inb(HD_ERROR)) != 1)
-		printk("hd: controller reset failed: %02x\n", hd_error);
-}
-
-static void reset_hd(void)
-{
-	static int i;
-
-repeat:
-	if (reset) {
-		reset = 0;
-		i = -1;
-		reset_controller();
-	} else {
-		check_status();
-		if (reset)
-			goto repeat;
-	}
-	if (++i < NR_HD) {
-		struct hd_i_struct *disk = &hd_info[i];
-		disk->special_op = disk->recalibrate = 1;
-		hd_out(disk, disk->sect, disk->sect, disk->head-1,
-			disk->cyl, WIN_SPECIFY, &reset_hd);
-		if (reset)
-			goto repeat;
-	} else
-		hd_request();
-}
-
-/*
- * Ok, don't know what to do with the unexpected interrupts: on some machines
- * doing a reset and a retry seems to result in an eternal loop. Right now I
- * ignore it, and just set the timeout.
- *
- * On laptops (and "green" PCs), an unexpected interrupt occurs whenever the
- * drive enters "idle", "standby", or "sleep" mode, so if the status looks
- * "good", we just ignore the interrupt completely.
- */
-static void unexpected_hd_interrupt(void)
-{
-	unsigned int stat = inb_p(HD_STATUS);
-
-	if (stat & (BUSY_STAT|DRQ_STAT|ECC_STAT|ERR_STAT)) {
-		dump_status("unexpected interrupt", stat);
-		SET_TIMER;
-	}
-}
-
-/*
- * bad_rw_intr() now tries to be a bit smarter and does things
- * according to the error returned by the controller.
- * -Mika Liljeberg (liljeber@cs.Helsinki.FI)
- */
-static void bad_rw_intr(void)
-{
-	struct request *req = CURRENT;
-	if (req != NULL) {
-		struct hd_i_struct *disk = req->rq_disk->private_data;
-		if (++req->errors >= MAX_ERRORS || (hd_error & BBD_ERR)) {
-			end_request(req, 0);
-			disk->special_op = disk->recalibrate = 1;
-		} else if (req->errors % RESET_FREQ == 0)
-			reset = 1;
-		else if ((hd_error & TRK0_ERR) || req->errors % RECAL_FREQ == 0)
-			disk->special_op = disk->recalibrate = 1;
-		/* Otherwise just retry */
-	}
-}
-
-static inline int wait_DRQ(void)
-{
-	int retries;
-	int stat;
-
-	for (retries = 0; retries < 100000; retries++) {
-		stat = inb_p(HD_STATUS);
-		if (stat & DRQ_STAT)
-			return 0;
-	}
-	dump_status("wait_DRQ", stat);
-	return -1;
-}
-
-static void read_intr(void)
-{
-	struct request *req;
-	int i, retries = 100000;
-
-	do {
-		i = (unsigned) inb_p(HD_STATUS);
-		if (i & BUSY_STAT)
-			continue;
-		if (!OK_STATUS(i))
-			break;
-		if (i & DRQ_STAT)
-			goto ok_to_read;
-	} while (--retries > 0);
-	dump_status("read_intr", i);
-	bad_rw_intr();
-	hd_request();
-	return;
-ok_to_read:
-	req = CURRENT;
-	insw(HD_DATA, req->buffer, 256);
-	req->sector++;
-	req->buffer += 512;
-	req->errors = 0;
-	i = --req->nr_sectors;
-	--req->current_nr_sectors;
-#ifdef DEBUG
-	printk("%s: read: sector %ld, remaining = %ld, buffer=%p\n",
-		req->rq_disk->disk_name, req->sector, req->nr_sectors,
-		req->buffer+512);
-#endif
-	if (req->current_nr_sectors <= 0)
-		end_request(req, 1);
-	if (i > 0) {
-		SET_HANDLER(&read_intr);
-		return;
-	}
-	(void) inb_p(HD_STATUS);
-#if (HD_DELAY > 0)
-	last_req = read_timer();
-#endif
-	if (elv_next_request(QUEUE))
-		hd_request();
-	return;
-}
-
-static void write_intr(void)
-{
-	struct request *req = CURRENT;
-	int i;
-	int retries = 100000;
-
-	do {
-		i = (unsigned) inb_p(HD_STATUS);
-		if (i & BUSY_STAT)
-			continue;
-		if (!OK_STATUS(i))
-			break;
-		if ((req->nr_sectors <= 1) || (i & DRQ_STAT))
-			goto ok_to_write;
-	} while (--retries > 0);
-	dump_status("write_intr", i);
-	bad_rw_intr();
-	hd_request();
-	return;
-ok_to_write:
-	req->sector++;
-	i = --req->nr_sectors;
-	--req->current_nr_sectors;
-	req->buffer += 512;
-	if (!i || (req->bio && req->current_nr_sectors <= 0))
-		end_request(req, 1);
-	if (i > 0) {
-		SET_HANDLER(&write_intr);
-		outsw(HD_DATA, req->buffer, 256);
-		local_irq_enable();
-	} else {
-#if (HD_DELAY > 0)
-		last_req = read_timer();
-#endif
-		hd_request();
-	}
-	return;
-}
-
-static void recal_intr(void)
-{
-	check_status();
-#if (HD_DELAY > 0)
-	last_req = read_timer();
-#endif
-	hd_request();
-}
-
-/*
- * This is another of the error-routines I don't know what to do with. The
- * best idea seems to just set reset, and start all over again.
- */
-static void hd_times_out(unsigned long dummy)
-{
-	char *name;
-
-	do_hd = NULL;
-
-	if (!CURRENT)
-		return;
-
-	disable_irq(HD_IRQ);
-	local_irq_enable();
-	reset = 1;
-	name = CURRENT->rq_disk->disk_name;
-	printk("%s: timeout\n", name);
-	if (++CURRENT->errors >= MAX_ERRORS) {
-#ifdef DEBUG
-		printk("%s: too many errors\n", name);
-#endif
-		end_request(CURRENT, 0);
-	}
-	local_irq_disable();
-	hd_request();
-	enable_irq(HD_IRQ);
-}
-
-static int do_special_op(struct hd_i_struct *disk, struct request *req)
-{
-	if (disk->recalibrate) {
-		disk->recalibrate = 0;
-		hd_out(disk, disk->sect, 0, 0, 0, WIN_RESTORE, &recal_intr);
-		return reset;
-	}
-	if (disk->head > 16) {
-		printk("%s: cannot handle device with more than 16 heads - giving up\n", req->rq_disk->disk_name);
-		end_request(req, 0);
-	}
-	disk->special_op = 0;
-	return 1;
-}
-
-/*
- * The driver enables interrupts as much as possible.  In order to do this,
- * (a) the device-interrupt is disabled before entering hd_request(),
- * and (b) the timeout-interrupt is disabled before the sti().
- *
- * Interrupts are still masked (by default) whenever we are exchanging
- * data/cmds with a drive, because some drives seem to have very poor
- * tolerance for latency during I/O. The IDE driver has support to unmask
- * interrupts for non-broken hardware, so use that driver if required.
- */
-static void hd_request(void)
-{
-	unsigned int block, nsect, sec, track, head, cyl;
-	struct hd_i_struct *disk;
-	struct request *req;
-
-	if (do_hd)
-		return;
-repeat:
-	del_timer(&device_timer);
-	local_irq_enable();
-
-	req = CURRENT;
-	if (!req) {
-		do_hd = NULL;
-		return;
-	}
-
-	if (reset) {
-		local_irq_disable();
-		reset_hd();
-		return;
-	}
-	disk = req->rq_disk->private_data;
-	block = req->sector;
-	nsect = req->nr_sectors;
-	if (block >= get_capacity(req->rq_disk) ||
-	    ((block+nsect) > get_capacity(req->rq_disk))) {
-		printk("%s: bad access: block=%d, count=%d\n",
-			req->rq_disk->disk_name, block, nsect);
-		end_request(req, 0);
-		goto repeat;
-	}
-
-	if (disk->special_op) {
-		if (do_special_op(disk, req))
-			goto repeat;
-		return;
-	}
-	sec   = block % disk->sect + 1;
-	track = block / disk->sect;
-	head  = track % disk->head;
-	cyl   = track / disk->head;
-#ifdef DEBUG
-	printk("%s: %sing: CHS=%d/%d/%d, sectors=%d, buffer=%p\n",
-		req->rq_disk->disk_name,
-		req_data_dir(req) == READ ? "read" : "writ",
-		cyl, head, sec, nsect, req->buffer);
-#endif
-	if (blk_fs_request(req)) {
-		switch (rq_data_dir(req)) {
-		case READ:
-			hd_out(disk, nsect, sec, head, cyl, WIN_READ,
-				&read_intr);
-			if (reset)
-				goto repeat;
-			break;
-		case WRITE:
-			hd_out(disk, nsect, sec, head, cyl, WIN_WRITE,
-				&write_intr);
-			if (reset)
-				goto repeat;
-			if (wait_DRQ()) {
-				bad_rw_intr();
-				goto repeat;
-			}
-			outsw(HD_DATA, req->buffer, 256);
-			break;
-		default:
-			printk("unknown hd-command\n");
-			end_request(req, 0);
-			break;
-		}
-	}
-}
-
-static void do_hd_request(struct request_queue *q)
-{
-	disable_irq(HD_IRQ);
-	hd_request();
-	enable_irq(HD_IRQ);
-}
-
-static int hd_getgeo(struct block_device *bdev, struct hd_geometry *geo)
-{
-	struct hd_i_struct *disk = bdev->bd_disk->private_data;
-
-	geo->heads = disk->head;
-	geo->sectors = disk->sect;
-	geo->cylinders = disk->cyl;
-	return 0;
-}
-
-/*
- * Releasing a block device means we sync() it, so that it can safely
- * be forgotten about...
- */
-
-static irqreturn_t hd_interrupt(int irq, void *dev_id)
-{
-	void (*handler)(void) = do_hd;
-
-	do_hd = NULL;
-	del_timer(&device_timer);
-	if (!handler)
-		handler = unexpected_hd_interrupt;
-	handler();
-	local_irq_enable();
-	return IRQ_HANDLED;
-}
-
-static struct block_device_operations hd_fops = {
-	.getgeo =	hd_getgeo,
-};
-
-/*
- * This is the hard disk IRQ description. The IRQF_DISABLED in sa_flags
- * means we run the IRQ-handler with interrupts disabled:  this is bad for
- * interrupt latency, but anything else has led to problems on some
- * machines.
- *
- * We enable interrupts in some of the routines after making sure it's
- * safe.
- */
-
-static int __init hd_init(void)
-{
-	int drive;
-
-	if (register_blkdev(MAJOR_NR, "hd"))
-		return -1;
-
-	hd_queue = blk_init_queue(do_hd_request, &hd_lock);
-	if (!hd_queue) {
-		unregister_blkdev(MAJOR_NR, "hd");
-		return -ENOMEM;
-	}
-
-	blk_queue_max_sectors(hd_queue, 255);
-	init_timer(&device_timer);
-	device_timer.function = hd_times_out;
-	blk_queue_hardsect_size(hd_queue, 512);
-
-	if (!NR_HD) {
-		/*
-		 * We don't know anything about the drive.  This means
-		 * that you *MUST* specify the drive parameters to the
-		 * kernel yourself.
-		 *
-		 * If we were on an i386, we used to read this info from
-		 * the BIOS or CMOS.  This doesn't work all that well,
-		 * since this assumes that this is a primary or secondary
-		 * drive, and if we're using this legacy driver, it's
-		 * probably an auxilliary controller added to recover
-		 * legacy data off an ST-506 drive.  Either way, it's
-		 * definitely safest to have the user explicitly specify
-		 * the information.
-		 */
-		printk("hd: no drives specified - use hd=cyl,head,sectors"
-			" on kernel command line\n");
-		goto out;
-	}
-
-	for (drive = 0 ; drive < NR_HD ; drive++) {
-		struct gendisk *disk = alloc_disk(64);
-		struct hd_i_struct *p = &hd_info[drive];
-		if (!disk)
-			goto Enomem;
-		disk->major = MAJOR_NR;
-		disk->first_minor = drive << 6;
-		disk->fops = &hd_fops;
-		sprintf(disk->disk_name, "hd%c", 'a'+drive);
-		disk->private_data = p;
-		set_capacity(disk, p->head * p->sect * p->cyl);
-		disk->queue = hd_queue;
-		p->unit = drive;
-		hd_gendisk[drive] = disk;
-		printk("%s: %luMB, CHS=%d/%d/%d\n",
-			disk->disk_name, (unsigned long)get_capacity(disk)/2048,
-			p->cyl, p->head, p->sect);
-	}
-
-	if (request_irq(HD_IRQ, hd_interrupt, IRQF_DISABLED, "hd", NULL)) {
-		printk("hd: unable to get IRQ%d for the hard disk driver\n",
-			HD_IRQ);
-		goto out1;
-	}
-	if (!request_region(HD_DATA, 8, "hd")) {
-		printk(KERN_WARNING "hd: port 0x%x busy\n", HD_DATA);
-		goto out2;
-	}
-	if (!request_region(HD_CMD, 1, "hd(cmd)")) {
-		printk(KERN_WARNING "hd: port 0x%x busy\n", HD_CMD);
-		goto out3;
-	}
-
-	/* Let them fly */
-	for (drive = 0; drive < NR_HD; drive++)
-		add_disk(hd_gendisk[drive]);
-
-	return 0;
-
-out3:
-	release_region(HD_DATA, 8);
-out2:
-	free_irq(HD_IRQ, NULL);
-out1:
-	for (drive = 0; drive < NR_HD; drive++)
-		put_disk(hd_gendisk[drive]);
-	NR_HD = 0;
-out:
-	del_timer(&device_timer);
-	unregister_blkdev(MAJOR_NR, "hd");
-	blk_cleanup_queue(hd_queue);
-	return -1;
-Enomem:
-	while (drive--)
-		put_disk(hd_gendisk[drive]);
-	goto out;
-}
-
-static int __init parse_hd_setup(char *line)
-{
-	int ints[6];
-
-	(void) get_options(line, ARRAY_SIZE(ints), ints);
-	hd_setup(NULL, ints);
-
-	return 1;
-}
-__setup("hd=", parse_hd_setup);
-
-module_init(hd_init);
diff --git a/drivers/ide/legacy/ht6560b.c b/drivers/ide/legacy/ht6560b.c
index 4fe516df9f7..7bc8fd59ea9 100644
--- a/drivers/ide/legacy/ht6560b.c
+++ b/drivers/ide/legacy/ht6560b.c
@@ -212,10 +212,11 @@ static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
 {
 	int active_time, recovery_time;
 	int active_cycles, recovery_cycles;
-	int bus_speed = ide_vlb_clk ? ide_vlb_clk : system_bus_clock();
+	int bus_speed = ide_vlb_clk ? ide_vlb_clk : 50;
 
         if (pio) {
 		unsigned int cycle_time;
+		struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
 
 		cycle_time = ide_pio_cycle_time(drive, pio);
 
@@ -224,10 +225,8 @@ static u8 ht_pio2timings(ide_drive_t *drive, const u8 pio)
 		 *  actual cycle time for recovery and activity
 		 *  according system bus speed.
 		 */
-		active_time = ide_pio_timings[pio].active_time;
-		recovery_time = cycle_time
-			- active_time
-			- ide_pio_timings[pio].setup_time;
+		active_time = t->active;
+		recovery_time = cycle_time - active_time - t->setup;
 		/*
 		 *  Cycle times should be Vesa bus cycles
 		 */
@@ -311,16 +310,16 @@ static void ht6560b_set_pio_mode(ide_drive_t *drive, const u8 pio)
 #endif
 }
 
-static void __init ht6560b_port_init_devs(ide_hwif_t *hwif)
+static void __init ht6560b_init_dev(ide_drive_t *drive)
 {
+	ide_hwif_t *hwif = drive->hwif;
 	/* Setting default configurations for drives. */
 	int t = (HT_CONFIG_DEFAULT << 8) | HT_TIMING_DEFAULT;
 
 	if (hwif->channel)
 		t |= (HT_SECONDARY_IF << 8);
 
-	hwif->drives[0].drive_data = t;
-	hwif->drives[1].drive_data = t;
+	drive->drive_data = t;
 }
 
 static int probe_ht6560b;
@@ -329,7 +328,7 @@ module_param_named(probe, probe_ht6560b, bool, 0);
 MODULE_PARM_DESC(probe, "probe for HT6560B chipset");
 
 static const struct ide_port_ops ht6560b_port_ops = {
-	.port_init_devs		= ht6560b_port_init_devs,
+	.init_dev		= ht6560b_init_dev,
 	.set_pio_mode		= ht6560b_set_pio_mode,
 	.selectproc		= ht6560b_selectproc,
 };
diff --git a/drivers/ide/legacy/ide-4drives.c b/drivers/ide/legacy/ide-4drives.c
index ecae916a338..89c8ff0a4d0 100644
--- a/drivers/ide/legacy/ide-4drives.c
+++ b/drivers/ide/legacy/ide-4drives.c
@@ -11,6 +11,21 @@ static int probe_4drives;
 module_param_named(probe, probe_4drives, bool, 0);
 MODULE_PARM_DESC(probe, "probe for generic IDE chipset with 4 drives/port");
 
+static void ide_4drives_init_dev(ide_drive_t *drive)
+{
+	if (drive->hwif->channel)
+		drive->select.all ^= 0x20;
+}
+
+static const struct ide_port_ops ide_4drives_port_ops = {
+	.init_dev		= ide_4drives_init_dev,
+};
+
+static const struct ide_port_info ide_4drives_port_info = {
+	.port_ops		= &ide_4drives_port_ops,
+	.host_flags		= IDE_HFLAG_SERIALIZE | IDE_HFLAG_NO_DMA,
+};
+
 static int __init ide_4drives_init(void)
 {
 	ide_hwif_t *hwif, *mate;
@@ -49,18 +64,10 @@ static int __init ide_4drives_init(void)
 	mate = ide_find_port();
 	if (mate) {
 		ide_init_port_hw(mate, &hw);
-		mate->drives[0].select.all ^= 0x20;
-		mate->drives[1].select.all ^= 0x20;
 		idx[1] = mate->index;
-
-		if (hwif) {
-			hwif->mate = mate;
-			mate->mate = hwif;
-			hwif->serialized = mate->serialized = 1;
-		}
 	}
 
-	ide_device_add(idx, NULL);
+	ide_device_add(idx, &ide_4drives_port_info);
 
 	return 0;
 }
diff --git a/drivers/ide/legacy/ide-cs.c b/drivers/ide/legacy/ide-cs.c
index 3381424d70a..27b1e0b7ecb 100644
--- a/drivers/ide/legacy/ide-cs.c
+++ b/drivers/ide/legacy/ide-cs.c
@@ -63,11 +63,9 @@ MODULE_LICENSE("Dual MPL/GPL");
 
 #define INT_MODULE_PARM(n, v) static int n = v; module_param(n, int, 0)
 
-#ifdef PCMCIA_DEBUG
-INT_MODULE_PARM(pc_debug, PCMCIA_DEBUG);
+#ifdef CONFIG_PCMCIA_DEBUG
+INT_MODULE_PARM(pc_debug, 0);
 #define DEBUG(n, args...) if (pc_debug>(n)) printk(KERN_DEBUG args)
-static char *version =
-"ide-cs.c 1.3 2002/10/26 05:45:31 (David Hinds)";
 #else
 #define DEBUG(n, args...)
 #endif
@@ -154,6 +152,11 @@ static const struct ide_port_ops idecs_port_ops = {
 	.quirkproc		= ide_undecoded_slave,
 };
 
+static const struct ide_port_info idecs_port_info = {
+	.port_ops		= &idecs_port_ops,
+	.host_flags		= IDE_HFLAG_NO_DMA,
+};
+
 static ide_hwif_t *idecs_register(unsigned long io, unsigned long ctl,
 				unsigned long irq, struct pcmcia_device *handle)
 {
@@ -187,13 +190,11 @@ static ide_hwif_t *idecs_register(unsigned long io, unsigned long ctl,
 
     i = hwif->index;
 
-    ide_init_port_data(hwif, i);
     ide_init_port_hw(hwif, &hw);
-    hwif->port_ops = &idecs_port_ops;
 
     idx[0] = i;
 
-    ide_device_add(idx, NULL);
+    ide_device_add(idx, &idecs_port_info);
 
     if (hwif->present)
 	return hwif;
@@ -375,7 +376,7 @@ failed:
 
 ======================================================================*/
 
-void ide_release(struct pcmcia_device *link)
+static void ide_release(struct pcmcia_device *link)
 {
     ide_info_t *info = link->priv;
     ide_hwif_t *hwif = info->hwif;
diff --git a/drivers/ide/legacy/ide_platform.c b/drivers/ide/legacy/ide_platform.c
index d3bc3f24e05..a249562b34b 100644
--- a/drivers/ide/legacy/ide_platform.c
+++ b/drivers/ide/legacy/ide_platform.c
@@ -44,6 +44,10 @@ static void __devinit plat_ide_setup_ports(hw_regs_t *hw,
 	hw->chipset = ide_generic;
 }
 
+static const struct ide_port_info platform_ide_port_info = {
+	.host_flags		= IDE_HFLAG_NO_DMA,
+};
+
 static int __devinit plat_ide_probe(struct platform_device *pdev)
 {
 	struct resource *res_base, *res_alt, *res_irq;
@@ -54,6 +58,7 @@ static int __devinit plat_ide_probe(struct platform_device *pdev)
 	int ret = 0;
 	int mmio = 0;
 	hw_regs_t hw;
+	struct ide_port_info d = platform_ide_port_info;
 
 	pdata = pdev->dev.platform_data;
 
@@ -102,13 +107,13 @@ static int __devinit plat_ide_probe(struct platform_device *pdev)
 	ide_init_port_hw(hwif, &hw);
 
 	if (mmio) {
-		hwif->host_flags = IDE_HFLAG_MMIO;
+		d.host_flags |= IDE_HFLAG_MMIO;
 		default_hwif_mmiops(hwif);
 	}
 
 	idx[0] = hwif->index;
 
-	ide_device_add(idx, NULL);
+	ide_device_add(idx, &d);
 
 	platform_set_drvdata(pdev, hwif);
 
diff --git a/drivers/ide/legacy/macide.c b/drivers/ide/legacy/macide.c
index 2e84290d0bc..0a6195bcfed 100644
--- a/drivers/ide/legacy/macide.c
+++ b/drivers/ide/legacy/macide.c
@@ -130,7 +130,6 @@ static int __init macide_init(void)
 		u8 index = hwif->index;
 		u8 idx[4] = { index, 0xff, 0xff, 0xff };
 
-		ide_init_port_data(hwif, index);
 		ide_init_port_hw(hwif, &hw);
 
 		ide_device_add(idx, NULL);
diff --git a/drivers/ide/legacy/q40ide.c b/drivers/ide/legacy/q40ide.c
index 8ff6e2d2083..9c2b9d078f6 100644
--- a/drivers/ide/legacy/q40ide.c
+++ b/drivers/ide/legacy/q40ide.c
@@ -142,7 +142,6 @@ static int __init q40ide_init(void)
 
 	hwif = ide_find_port();
 	if (hwif) {
-		ide_init_port_data(hwif, hwif->index);
 		ide_init_port_hw(hwif, &hw);
 
 		/* Q40 has a byte-swapped IDE interface */
diff --git a/drivers/ide/legacy/qd65xx.c b/drivers/ide/legacy/qd65xx.c
index 6424af15432..2338f344ea2 100644
--- a/drivers/ide/legacy/qd65xx.c
+++ b/drivers/ide/legacy/qd65xx.c
@@ -110,7 +110,7 @@ static void qd65xx_select(ide_drive_t *drive)
 
 static u8 qd6500_compute_timing (ide_hwif_t *hwif, int active_time, int recovery_time)
 {
-	int clk = ide_vlb_clk ? ide_vlb_clk : system_bus_clock();
+	int clk = ide_vlb_clk ? ide_vlb_clk : 50;
 	u8 act_cyc, rec_cyc;
 
 	if (clk <= 33) {
@@ -132,7 +132,7 @@ static u8 qd6500_compute_timing (ide_hwif_t *hwif, int active_time, int recovery
 
 static u8 qd6580_compute_timing (int active_time, int recovery_time)
 {
-	int clk = ide_vlb_clk ? ide_vlb_clk : system_bus_clock();
+	int clk = ide_vlb_clk ? ide_vlb_clk : 50;
 	u8 act_cyc, rec_cyc;
 
 	act_cyc = 17 - IDE_IN(active_time   * clk / 1000 + 1, 2, 17);
@@ -207,6 +207,7 @@ static void qd6500_set_pio_mode(ide_drive_t *drive, const u8 pio)
 static void qd6580_set_pio_mode(ide_drive_t *drive, const u8 pio)
 {
 	ide_hwif_t *hwif = drive->hwif;
+	struct ide_timing *t = ide_timing_find_mode(XFER_PIO_0 + pio);
 	unsigned int cycle_time;
 	int active_time   = 175;
 	int recovery_time = 415; /* worst case values from the dos driver */
@@ -236,7 +237,7 @@ static void qd6580_set_pio_mode(ide_drive_t *drive, const u8 pio)
 					active_time = 110;
 					recovery_time = cycle_time - 120;
 				} else {
-					active_time = ide_pio_timings[pio].active_time;
+					active_time = t->active;
 					recovery_time = cycle_time - active_time;
 				}
 		}
@@ -281,17 +282,18 @@ static int __init qd_testreg(int port)
 	return (readreg != QD_TESTVAL);
 }
 
-static void __init qd6500_port_init_devs(ide_hwif_t *hwif)
+static void __init qd6500_init_dev(ide_drive_t *drive)
 {
+	ide_hwif_t *hwif = drive->hwif;
 	u8 base = (hwif->config_data & 0xff00) >> 8;
 	u8 config = QD_CONFIG(hwif);
 
-	hwif->drives[0].drive_data = QD6500_DEF_DATA;
-	hwif->drives[1].drive_data = QD6500_DEF_DATA;
+	drive->drive_data = QD6500_DEF_DATA;
 }
 
-static void __init qd6580_port_init_devs(ide_hwif_t *hwif)
+static void __init qd6580_init_dev(ide_drive_t *drive)
 {
+	ide_hwif_t *hwif = drive->hwif;
 	u16 t1, t2;
 	u8 base = (hwif->config_data & 0xff00) >> 8;
 	u8 config = QD_CONFIG(hwif);
@@ -302,18 +304,17 @@ static void __init qd6580_port_init_devs(ide_hwif_t *hwif)
 	} else
 		t2 = t1 = hwif->channel ? QD6580_DEF_DATA2 : QD6580_DEF_DATA;
 
-	hwif->drives[0].drive_data = t1;
-	hwif->drives[1].drive_data = t2;
+	drive->drive_data = drive->select.b.unit ? t2 : t1;
 }
 
 static const struct ide_port_ops qd6500_port_ops = {
-	.port_init_devs		= qd6500_port_init_devs,
+	.init_dev		= qd6500_init_dev,
 	.set_pio_mode		= qd6500_set_pio_mode,
 	.selectproc		= qd65xx_select,
 };
 
 static const struct ide_port_ops qd6580_port_ops = {
-	.port_init_devs		= qd6580_port_init_devs,
+	.init_dev		= qd6580_init_dev,
 	.set_pio_mode		= qd6580_set_pio_mode,
 	.selectproc		= qd65xx_select,
 };