Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 165 insertions, 0 deletions

diff --git a/drivers/ide/legacy/dtc2278.c b/drivers/ide/legacy/dtc2278.c
new file mode 100644
index 00000000000..20eb5b872ca
--- /dev/null
+++ b/drivers/ide/legacy/dtc2278.c
@@ -0,0 +1,165 @@
+/*
+ *  linux/drivers/ide/legacy/dtc2278.c		Version 0.02	Feb 10, 1996
+ *
+ *  Copyright (C) 1996  Linus Torvalds & author (see below)
+ */
+
+#undef REALLY_SLOW_IO           /* most systems can safely undef this */
+
+#include <linux/module.h>
+#include <linux/config.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/mm.h>
+#include <linux/ioport.h>
+#include <linux/blkdev.h>
+#include <linux/hdreg.h>
+#include <linux/ide.h>
+#include <linux/init.h>
+
+#include <asm/io.h>
+
+/*
+ * Changing this #undef to #define may solve start up problems in some systems.
+ */
+#undef ALWAYS_SET_DTC2278_PIO_MODE
+
+/*
+ * From: andy@cercle.cts.com (Dyan Wile)
+ *
+ * Below is a patch for DTC-2278 - alike software-programmable controllers
+ * The code enables the secondary IDE controller and the PIO4 (3?) timings on
+ * the primary (EIDE). You may probably have to enable the 32-bit support to
+ * get the full speed. You better get the disk interrupts disabled ( hdparm -u0
+ * /dev/hd.. ) for the drives connected to the EIDE interface. (I get my
+ * filesystem  corrupted with -u1, but under heavy disk load only :-)
+ *
+ * This card is now forced to use the "serialize" feature,
+ * and irq-unmasking is disallowed.  If io_32bit is enabled,
+ * it must be done for BOTH drives on each interface.
+ *
+ * This code was written for the DTC2278E, but might work with any of these:
+ *
+ * DTC2278S has only a single IDE interface.
+ * DTC2278D has two IDE interfaces and is otherwise identical to the S version.
+ * DTC2278E also has serial ports and a printer port
+ * DTC2278EB: has onboard BIOS, and "works like a charm" -- Kent Bradford <kent@theory.caltech.edu>
+ *
+ * There may be a fourth controller type. The S and D versions use the
+ * Winbond chip, and I think the E version does also.
+ *
+ */
+
+static void sub22 (char b, char c)
+{
+	int i;
+
+	for(i = 0; i < 3; ++i) {
+		inb(0x3f6);
+		outb_p(b,0xb0);
+		inb(0x3f6);
+		outb_p(c,0xb4);
+		inb(0x3f6);
+		if(inb(0xb4) == c) {
+			outb_p(7,0xb0);
+			inb(0x3f6);
+			return;	/* success */
+		}
+	}
+}
+
+static void tune_dtc2278 (ide_drive_t *drive, u8 pio)
+{
+	unsigned long flags;
+
+	pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
+
+	if (pio >= 3) {
+		spin_lock_irqsave(&ide_lock, flags);
+		/*
+		 * This enables PIO mode4 (3?) on the first interface
+		 */
+		sub22(1,0xc3);
+		sub22(0,0xa0);
+		spin_unlock_irqrestore(&ide_lock, flags);
+	} else {
+		/* we don't know how to set it back again.. */
+	}
+
+	/*
+	 * 32bit I/O has to be enabled for *both* drives at the same time.
+	 */
+	drive->io_32bit = 1;
+	HWIF(drive)->drives[!drive->select.b.unit].io_32bit = 1;
+}
+
+static int __init probe_dtc2278(void)
+{
+	unsigned long flags;
+	ide_hwif_t *hwif, *mate;
+
+	hwif = &ide_hwifs[0];
+	mate = &ide_hwifs[1];
+
+	if (hwif->chipset != ide_unknown || mate->chipset != ide_unknown)
+		return 1;
+
+	local_irq_save(flags);
+	/*
+	 * This enables the second interface
+	 */
+	outb_p(4,0xb0);
+	inb(0x3f6);
+	outb_p(0x20,0xb4);
+	inb(0x3f6);
+#ifdef ALWAYS_SET_DTC2278_PIO_MODE
+	/*
+	 * This enables PIO mode4 (3?) on the first interface
+	 * and may solve start-up problems for some people.
+	 */
+	sub22(1,0xc3);
+	sub22(0,0xa0);
+#endif
+	local_irq_restore(flags);
+
+	hwif->serialized = 1;
+	hwif->chipset = ide_dtc2278;
+	hwif->tuneproc = &tune_dtc2278;
+	hwif->drives[0].no_unmask = 1;
+	hwif->drives[1].no_unmask = 1;
+	hwif->mate = mate;
+
+	mate->serialized = 1;
+	mate->chipset = ide_dtc2278;
+	mate->drives[0].no_unmask = 1;
+	mate->drives[1].no_unmask = 1;
+	mate->mate = hwif;
+	mate->channel = 1;
+
+	probe_hwif_init(hwif);
+	probe_hwif_init(mate);
+
+	create_proc_ide_interfaces();
+
+	return 0;
+}
+
+/* Can be called directly from ide.c. */
+int __init dtc2278_init(void)
+{
+	if (probe_dtc2278()) {
+		printk(KERN_ERR "dtc2278: ide interfaces already in use!\n");
+		return -EBUSY;
+	}
+	return 0;
+}
+
+#ifdef MODULE
+module_init(dtc2278_init);
+#endif
+
+MODULE_AUTHOR("See Local File");
+MODULE_DESCRIPTION("support of DTC-2278 VLB IDE chipsets");
+MODULE_LICENSE("GPL");