ide: remove useless subdirs from drivers/ide/

Suggested-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

1 files changed, 165 insertions, 0 deletions

diff --git a/drivers/ide/cs5520.c b/drivers/ide/cs5520.c
new file mode 100644
index 00000000000..5efb467f8fa
--- /dev/null
+++ b/drivers/ide/cs5520.c
@@ -0,0 +1,165 @@
+/*
+ *	IDE tuning and bus mastering support for the CS5510/CS5520
+ *	chipsets
+ *
+ *	The CS5510/CS5520 are slightly unusual devices. Unlike the 
+ *	typical IDE controllers they do bus mastering with the drive in
+ *	PIO mode and smarter silicon.
+ *
+ *	The practical upshot of this is that we must always tune the
+ *	drive for the right PIO mode. We must also ignore all the blacklists
+ *	and the drive bus mastering DMA information.
+ *
+ *	*** This driver is strictly experimental ***
+ *
+ *	(c) Copyright Red Hat Inc 2002
+ * 
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2, or (at your option) any
+ * later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * General Public License for more details.
+ *
+ * For the avoidance of doubt the "preferred form" of this code is one which
+ * is in an open non patent encumbered format. Where cryptographic key signing
+ * forms part of the process of creating an executable the information
+ * including keys needed to generate an equivalently functional executable
+ * are deemed to be part of the source code.
+ *
+ */
+ 
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+#include <linux/dma-mapping.h>
+
+#define DRV_NAME "cs5520"
+
+struct pio_clocks
+{
+	int address;
+	int assert;
+	int recovery;
+};
+
+static struct pio_clocks cs5520_pio_clocks[]={
+	{3, 6, 11},
+	{2, 5, 6},
+	{1, 4, 3},
+	{1, 3, 2},
+	{1, 2, 1}
+};
+
+static void cs5520_set_pio_mode(ide_drive_t *drive, const u8 pio)
+{
+	ide_hwif_t *hwif = HWIF(drive);
+	struct pci_dev *pdev = to_pci_dev(hwif->dev);
+	int controller = drive->dn > 1 ? 1 : 0;
+
+	/* 8bit CAT/CRT - 8bit command timing for channel */
+	pci_write_config_byte(pdev, 0x62 + controller, 
+		(cs5520_pio_clocks[pio].recovery << 4) |
+		(cs5520_pio_clocks[pio].assert));
+
+	/* 0x64 - 16bit Primary, 0x68 - 16bit Secondary */
+
+	/* FIXME: should these use address ? */
+	/* Data read timing */
+	pci_write_config_byte(pdev, 0x64 + 4*controller + (drive->dn&1),
+		(cs5520_pio_clocks[pio].recovery << 4) |
+		(cs5520_pio_clocks[pio].assert));
+	/* Write command timing */
+	pci_write_config_byte(pdev, 0x66 + 4*controller + (drive->dn&1),
+		(cs5520_pio_clocks[pio].recovery << 4) |
+		(cs5520_pio_clocks[pio].assert));
+}
+
+static void cs5520_set_dma_mode(ide_drive_t *drive, const u8 speed)
+{
+	printk(KERN_ERR "cs55x0: bad ide timing.\n");
+
+	cs5520_set_pio_mode(drive, 0);
+}
+
+static const struct ide_port_ops cs5520_port_ops = {
+	.set_pio_mode		= cs5520_set_pio_mode,
+	.set_dma_mode		= cs5520_set_dma_mode,
+};
+
+static const struct ide_port_info cyrix_chipset __devinitdata = {
+	.name		= DRV_NAME,
+	.enablebits	= { { 0x60, 0x01, 0x01 }, { 0x60, 0x02, 0x02 } },
+	.port_ops	= &cs5520_port_ops,
+	.host_flags	= IDE_HFLAG_ISA_PORTS | IDE_HFLAG_CS5520,
+	.pio_mask	= ATA_PIO4,
+};
+
+/*
+ *	The 5510/5520 are a bit weird. They don't quite set up the way
+ *	the PCI helper layer expects so we must do much of the set up 
+ *	work longhand.
+ */
+ 
+static int __devinit cs5520_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+	const struct ide_port_info *d = &cyrix_chipset;
+	hw_regs_t hw[4], *hws[] = { NULL, NULL, NULL, NULL };
+
+	ide_setup_pci_noise(dev, d);
+
+	/* We must not grab the entire device, it has 'ISA' space in its
+	 * BARS too and we will freak out other bits of the kernel
+	 */
+	if (pci_enable_device_io(dev)) {
+		printk(KERN_WARNING "%s: Unable to enable 55x0.\n", d->name);
+		return -ENODEV;
+	}
+	pci_set_master(dev);
+	if (pci_set_dma_mask(dev, DMA_32BIT_MASK)) {
+		printk(KERN_WARNING "%s: No suitable DMA available.\n",
+			d->name);
+		return -ENODEV;
+	}
+
+	/*
+	 *	Now the chipset is configured we can let the core
+	 *	do all the device setup for us
+	 */
+
+	ide_pci_setup_ports(dev, d, 14, &hw[0], &hws[0]);
+
+	return ide_host_add(d, hws, NULL);
+}
+
+static const struct pci_device_id cs5520_pci_tbl[] = {
+	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), 0 },
+	{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), 1 },
+	{ 0, },
+};
+MODULE_DEVICE_TABLE(pci, cs5520_pci_tbl);
+
+static struct pci_driver cs5520_pci_driver = {
+	.name		= "Cyrix_IDE",
+	.id_table	= cs5520_pci_tbl,
+	.probe		= cs5520_init_one,
+	.suspend	= ide_pci_suspend,
+	.resume		= ide_pci_resume,
+};
+
+static int __init cs5520_ide_init(void)
+{
+	return ide_pci_register_driver(&cs5520_pci_driver);
+}
+
+module_init(cs5520_ide_init);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("PCI driver module for Cyrix 5510/5520 IDE");
+MODULE_LICENSE("GPL");