Merge branch 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:
 "Here is the pull request from the i2c subsystem.  It got a little
  delayed because I needed to wait for a dependency to be included
  (commit b424080a9e08: "reset: Add optional resets and stubs").  Plus,
  I had some email problems.  All done now, the highlights are:

   - drivers can now deprecate their use of i2c classes.  That shouldn't
     be used on embedded platforms anyhow and was often blindly
     copy&pasted.  This mechanism gives users time to switch away and
     ultimately boot faster once the use of classes for those drivers is
     gone for good.

   - new drivers for QUP, Cadence, efm32

   - tracepoint support for I2C and SMBus

   - bigger cleanups for the mv64xxx, nomadik, and designware drivers

  And the usual bugfixes, cleanups, feature additions.  Most stuff has
  been in linux-next for a while.  Just some hot fixes and new drivers
  were added a bit more recently."

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (63 commits)
  i2c: cadence: fix Kconfig dependency
  i2c: Add driver for Cadence I2C controller
  i2c: cadence: Document device tree bindings
  Documentation: i2c: improve section about flags mangling the protocol
  i2c: qup: use proper type fro clk_freq
  i2c: qup: off by ones in qup_i2c_probe()
  i2c: efm32: fix binding doc
  MAINTAINERS: update I2C web resources
  i2c: qup: New bus driver for the Qualcomm QUP I2C controller
  i2c: qup: Add device tree bindings information
  i2c: i2c-xiic: deprecate class based instantiation
  i2c: i2c-sirf: deprecate class based instantiation
  i2c: i2c-mv64xxx: deprecate class based instantiation
  i2c: i2c-designware-platdrv: deprecate class based instantiation
  i2c: i2c-davinci: deprecate class based instantiation
  i2c: i2c-bcm2835: deprecate class based instantiation
  i2c: mv64xxx: Fix reset controller handling
  i2c: omap: fix usage of IS_ERR_VALUE with pm_runtime_get_sync
  i2c: efm32: new bus driver
  i2c: exynos5: remove unnecessary cast of void pointer
  ...

47 files changed, 2593 insertions, 345 deletions

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index 014afab1d55..c94db1c5e35 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -110,6 +110,7 @@ config I2C_I801
 	    Wellsburg (PCH)
 	    Coleto Creek (PCH)
 	    Wildcat Point-LP (PCH)
+	    BayTrail (SOC)
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-i801.
@@ -375,6 +376,13 @@ config I2C_BLACKFIN_TWI_CLK_KHZ
 	help
 	  The unit of the TWI clock is kHz.
 
+config I2C_CADENCE
+	tristate "Cadence I2C Controller"
+	depends on ARCH_ZYNQ
+	help
+	  Say yes here to select Cadence I2C Host Controller. This controller is
+	  e.g. used by Xilinx Zynq.
+
 config I2C_CBUS_GPIO
 	tristate "CBUS I2C driver"
 	depends on GPIOLIB
@@ -432,6 +440,13 @@ config I2C_DESIGNWARE_PCI
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-designware-pci.
 
+config I2C_EFM32
+	tristate "EFM32 I2C controller"
+	depends on ARCH_EFM32 || COMPILE_TEST
+	help
+	  This driver supports the i2c block found in Energy Micro's EFM32
+	  SoCs.
+
 config I2C_EG20T
 	tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) I2C"
 	depends on PCI
@@ -527,7 +542,7 @@ config I2C_MPC
 
 config I2C_MV64XXX
 	tristate "Marvell mv64xxx I2C Controller"
-	depends on (MV64X60 || PLAT_ORION || ARCH_SUNXI)
+	depends on MV64X60 || PLAT_ORION || ARCH_SUNXI
 	help
 	  If you say yes to this option, support will be included for the
 	  built-in I2C interface on the Marvell 64xxx line of host bridges.
@@ -648,6 +663,16 @@ config I2C_PXA_SLAVE
 	  is necessary for systems where the PXA may be a target on the
 	  I2C bus.
 
+config I2C_QUP
+	tristate "Qualcomm QUP based I2C controller"
+	depends on ARCH_QCOM
+	help
+	  If you say yes to this option, support will be included for the
+	  built-in I2C interface on the Qualcomm SoCs.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-qup.
+
 config I2C_RIIC
 	tristate "Renesas RIIC adapter"
 	depends on ARCH_SHMOBILE || COMPILE_TEST
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index a08931fe73e..18d18ff9db9 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -33,6 +33,7 @@ obj-$(CONFIG_I2C_AT91)		+= i2c-at91.o
 obj-$(CONFIG_I2C_AU1550)	+= i2c-au1550.o
 obj-$(CONFIG_I2C_BCM2835)	+= i2c-bcm2835.o
 obj-$(CONFIG_I2C_BLACKFIN_TWI)	+= i2c-bfin-twi.o
+obj-$(CONFIG_I2C_CADENCE)	+= i2c-cadence.o
 obj-$(CONFIG_I2C_CBUS_GPIO)	+= i2c-cbus-gpio.o
 obj-$(CONFIG_I2C_CPM)		+= i2c-cpm.o
 obj-$(CONFIG_I2C_DAVINCI)	+= i2c-davinci.o
@@ -41,6 +42,7 @@ obj-$(CONFIG_I2C_DESIGNWARE_PLATFORM)	+= i2c-designware-platform.o
 i2c-designware-platform-objs := i2c-designware-platdrv.o
 obj-$(CONFIG_I2C_DESIGNWARE_PCI)	+= i2c-designware-pci.o
 i2c-designware-pci-objs := i2c-designware-pcidrv.o
+obj-$(CONFIG_I2C_EFM32)		+= i2c-efm32.o
 obj-$(CONFIG_I2C_EG20T)		+= i2c-eg20t.o
 obj-$(CONFIG_I2C_EXYNOS5)	+= i2c-exynos5.o
 obj-$(CONFIG_I2C_GPIO)		+= i2c-gpio.o
@@ -63,6 +65,7 @@ obj-$(CONFIG_I2C_PNX)		+= i2c-pnx.o
 obj-$(CONFIG_I2C_PUV3)		+= i2c-puv3.o
 obj-$(CONFIG_I2C_PXA)		+= i2c-pxa.o
 obj-$(CONFIG_I2C_PXA_PCI)	+= i2c-pxa-pci.o
+obj-$(CONFIG_I2C_QUP)		+= i2c-qup.o
 obj-$(CONFIG_I2C_RIIC)		+= i2c-riic.o
 obj-$(CONFIG_I2C_S3C2410)	+= i2c-s3c2410.o
 obj-$(CONFIG_I2C_S6000)		+= i2c-s6000.o
diff --git a/drivers/i2c/busses/i2c-ali1535.c b/drivers/i2c/busses/i2c-ali1535.c
index 7d60d3a1f62..451e305f797 100644
--- a/drivers/i2c/busses/i2c-ali1535.c
+++ b/drivers/i2c/busses/i2c-ali1535.c
@@ -494,7 +494,7 @@ static struct i2c_adapter ali1535_adapter = {
 	.algo		= &smbus_algorithm,
 };
 
-static DEFINE_PCI_DEVICE_TABLE(ali1535_ids) = {
+static const struct pci_device_id ali1535_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101) },
 	{ },
 };
diff --git a/drivers/i2c/busses/i2c-ali1563.c b/drivers/i2c/busses/i2c-ali1563.c
index 4611e4754a6..98a1c97739b 100644
--- a/drivers/i2c/busses/i2c-ali1563.c
+++ b/drivers/i2c/busses/i2c-ali1563.c
@@ -416,7 +416,7 @@ static void ali1563_remove(struct pci_dev *dev)
 	ali1563_shutdown(dev);
 }
 
-static DEFINE_PCI_DEVICE_TABLE(ali1563_id_table) = {
+static const struct pci_device_id ali1563_id_table[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M1563) },
 	{},
 };
diff --git a/drivers/i2c/busses/i2c-ali15x3.c b/drivers/i2c/busses/i2c-ali15x3.c
index 4823206a487..2fa21ce9682 100644
--- a/drivers/i2c/busses/i2c-ali15x3.c
+++ b/drivers/i2c/busses/i2c-ali15x3.c
@@ -476,7 +476,7 @@ static struct i2c_adapter ali15x3_adapter = {
 	.algo		= &smbus_algorithm,
 };
 
-static DEFINE_PCI_DEVICE_TABLE(ali15x3_ids) = {
+static const struct pci_device_id ali15x3_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_AL, PCI_DEVICE_ID_AL_M7101) },
 	{ 0, }
 };
diff --git a/drivers/i2c/busses/i2c-amd756.c b/drivers/i2c/busses/i2c-amd756.c
index 819d3c1062a..a16f7289135 100644
--- a/drivers/i2c/busses/i2c-amd756.c
+++ b/drivers/i2c/busses/i2c-amd756.c
@@ -307,7 +307,7 @@ static const char* chipname[] = {
 	"nVidia nForce", "AMD8111",
 };
 
-static DEFINE_PCI_DEVICE_TABLE(amd756_ids) = {
+static const struct pci_device_id amd756_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_740B),
 	  .driver_data = AMD756 },
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_VIPER_7413),
diff --git a/drivers/i2c/busses/i2c-amd8111.c b/drivers/i2c/busses/i2c-amd8111.c
index f3d4d79855b..95a80a8f81b 100644
--- a/drivers/i2c/busses/i2c-amd8111.c
+++ b/drivers/i2c/busses/i2c-amd8111.c
@@ -414,7 +414,7 @@ static const struct i2c_algorithm smbus_algorithm = {
 };
 
 
-static DEFINE_PCI_DEVICE_TABLE(amd8111_ids) = {
+static const struct pci_device_id amd8111_ids[] = {
 	{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8111_SMBUS2) },
 	{ 0, }
 };
diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index 843d01268ae..e95f9ba9679 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -32,7 +32,7 @@
 #include <linux/slab.h>
 #include <linux/platform_data/dma-atmel.h>
 
-#define TWI_CLK_HZ		100000			/* max 400 Kbits/s */
+#define DEFAULT_TWI_CLK_HZ		100000		/* max 400 Kbits/s */
 #define AT91_I2C_TIMEOUT	msecs_to_jiffies(100)	/* transfer timeout */
 #define AT91_I2C_DMA_THRESHOLD	8			/* enable DMA if transfer size is bigger than this threshold */
 
@@ -711,6 +711,7 @@ static int at91_twi_probe(struct platform_device *pdev)
 	struct resource *mem;
 	int rc;
 	u32 phy_addr;
+	u32 bus_clk_rate;
 
 	dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL);
 	if (!dev)
@@ -756,13 +757,18 @@ static int at91_twi_probe(struct platform_device *pdev)
 			dev->use_dma = true;
 	}
 
-	at91_calc_twi_clock(dev, TWI_CLK_HZ);
+	rc = of_property_read_u32(dev->dev->of_node, "clock-frequency",
+			&bus_clk_rate);
+	if (rc)
+		bus_clk_rate = DEFAULT_TWI_CLK_HZ;
+
+	at91_calc_twi_clock(dev, bus_clk_rate);
 	at91_init_twi_bus(dev);
 
 	snprintf(dev->adapter.name, sizeof(dev->adapter.name), "AT91");
 	i2c_set_adapdata(&dev->adapter, dev);
 	dev->adapter.owner = THIS_MODULE;
-	dev->adapter.class = I2C_CLASS_HWMON;
+	dev->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_DEPRECATED;
 	dev->adapter.algo = &at91_twi_algorithm;
 	dev->adapter.dev.parent = dev->dev;
 	dev->adapter.nr = pdev->id;
diff --git a/drivers/i2c/busses/i2c-bcm2835.c b/drivers/i2c/busses/i2c-bcm2835.c
index 77df97b932a..c60719577fc 100644
--- a/drivers/i2c/busses/i2c-bcm2835.c
+++ b/drivers/i2c/busses/i2c-bcm2835.c
@@ -219,7 +219,7 @@ static const struct i2c_algorithm bcm2835_i2c_algo = {
 static int bcm2835_i2c_probe(struct platform_device *pdev)
 {
 	struct bcm2835_i2c_dev *i2c_dev;
-	struct resource *mem, *requested, *irq;
+	struct resource *mem, *irq;
 	u32 bus_clk_rate, divider;
 	int ret;
 	struct i2c_adapter *adap;
@@ -234,25 +234,9 @@ static int bcm2835_i2c_probe(struct platform_device *pdev)
 	init_completion(&i2c_dev->completion);
 
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!mem) {
-		dev_err(&pdev->dev, "No mem resource\n");
-		return -ENODEV;
-	}
-
-	requested = devm_request_mem_region(&pdev->dev, mem->start,
-					    resource_size(mem),
-					    dev_name(&pdev->dev));
-	if (!requested) {
-		dev_err(&pdev->dev, "Could not claim register region\n");
-		return -EBUSY;
-	}
-
-	i2c_dev->regs = devm_ioremap(&pdev->dev, mem->start,
-				     resource_size(mem));
-	if (!i2c_dev->regs) {
-		dev_err(&pdev->dev, "Could not map registers\n");
-		return -ENOMEM;
-	}
+	i2c_dev->regs = devm_ioremap_resource(&pdev->dev, mem);
+	if (IS_ERR(i2c_dev->regs))
+		return PTR_ERR(i2c_dev->regs);
 
 	i2c_dev->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(i2c_dev->clk)) {
@@ -295,7 +279,7 @@ static int bcm2835_i2c_probe(struct platform_device *pdev)
 	adap = &i2c_dev->adapter;
 	i2c_set_adapdata(adap, i2c_dev);
 	adap->owner = THIS_MODULE;
-	adap->class = I2C_CLASS_HWMON;
+	adap->class = I2C_CLASS_HWMON | I2C_CLASS_DEPRECATED;
 	strlcpy(adap->name, "bcm2835 I2C adapter", sizeof(adap->name));
 	adap->algo = &bcm2835_i2c_algo;
 	adap->dev.parent = &pdev->dev;
diff --git a/drivers/i2c/busses/i2c-bfin-twi.c b/drivers/i2c/busses/i2c-bfin-twi.c
index 3b9bd9a3f2b..e6d5162b637 100644
--- a/drivers/i2c/busses/i2c-bfin-twi.c
+++ b/drivers/i2c/busses/i2c-bfin-twi.c
@@ -21,10 +21,10 @@
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
 #include <linux/delay.h>
+#include <linux/i2c/bfin_twi.h>
 
-#include <asm/blackfin.h>
-#include <asm/portmux.h>
 #include <asm/irq.h>
+#include <asm/portmux.h>
 #include <asm/bfin_twi.h>
 
 /* SMBus mode*/
@@ -65,7 +65,6 @@ static void bfin_twi_handle_interrupt(struct bfin_twi_iface *iface,
 		/* Transmit next data */
 		while (iface->writeNum > 0 &&
 			(read_FIFO_STAT(iface) & XMTSTAT) != XMT_FULL) {
-			SSYNC();
 			write_XMT_DATA8(iface, *(iface->transPtr++));
 			iface->writeNum--;
 		}
@@ -248,7 +247,6 @@ static irqreturn_t bfin_twi_interrupt_entry(int irq, void *dev_id)
 		/* Clear interrupt status */
 		write_INT_STAT(iface, twi_int_status);
 		bfin_twi_handle_interrupt(iface, twi_int_status);
-		SSYNC();
 	}
 	spin_unlock_irqrestore(&iface->lock, flags);
 	return IRQ_HANDLED;
@@ -294,9 +292,7 @@ static int bfin_twi_do_master_xfer(struct i2c_adapter *adap,
 	 *  discarded before start a new operation.
 	 */
 	write_FIFO_CTL(iface, 0x3);
-	SSYNC();
 	write_FIFO_CTL(iface, 0);
-	SSYNC();
 
 	if (pmsg->flags & I2C_M_RD)
 		iface->read_write = I2C_SMBUS_READ;
@@ -306,7 +302,6 @@ static int bfin_twi_do_master_xfer(struct i2c_adapter *adap,
 		if (iface->writeNum > 0) {
 			write_XMT_DATA8(iface, *(iface->transPtr++));
 			iface->writeNum--;
-			SSYNC();
 		}
 	}
 
@@ -315,7 +310,6 @@ static int bfin_twi_do_master_xfer(struct i2c_adapter *adap,
 
 	/* Interrupt mask . Enable XMT, RCV interrupt */
 	write_INT_MASK(iface, MCOMP | MERR | RCVSERV | XMTSERV);
-	SSYNC();
 
 	if (pmsg->len <= 255)
 		write_MASTER_CTL(iface, pmsg->len << 6);
@@ -329,7 +323,6 @@ static int bfin_twi_do_master_xfer(struct i2c_adapter *adap,
 		(iface->msg_num > 1 ? RSTART : 0) |
 		((iface->read_write == I2C_SMBUS_READ) ? MDIR : 0) |
 		((CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ > 100) ? FAST : 0));
-	SSYNC();
 
 	while (!iface->result) {
 		if (!wait_for_completion_timeout(&iface->complete,
@@ -453,7 +446,6 @@ int bfin_twi_do_smbus_xfer(struct i2c_adapter *adap, u16 addr,
 	 * start a new operation.
 	 */
 	write_FIFO_CTL(iface, 0x3);
-	SSYNC();
 	write_FIFO_CTL(iface, 0);
 
 	/* clear int stat */
@@ -461,7 +453,6 @@ int bfin_twi_do_smbus_xfer(struct i2c_adapter *adap, u16 addr,
 
 	/* Set Transmit device address */
 	write_MASTER_ADDR(iface, addr);
-	SSYNC();
 
 	switch (iface->cur_mode) {
 	case TWI_I2C_MODE_STANDARDSUB:
@@ -469,7 +460,6 @@ int bfin_twi_do_smbus_xfer(struct i2c_adapter *adap, u16 addr,
 		write_INT_MASK(iface, MCOMP | MERR |
 			((iface->read_write == I2C_SMBUS_READ) ?
 			RCVSERV : XMTSERV));
-		SSYNC();
 
 		if (iface->writeNum + 1 <= 255)
 			write_MASTER_CTL(iface, (iface->writeNum + 1) << 6);
@@ -484,7 +474,6 @@ int bfin_twi_do_smbus_xfer(struct i2c_adapter *adap, u16 addr,
 	case TWI_I2C_MODE_COMBINED:
 		write_XMT_DATA8(iface, iface->command);
 		write_INT_MASK(iface, MCOMP | MERR | RCVSERV | XMTSERV);
-		SSYNC();
 
 		if (iface->writeNum > 0)
 			write_MASTER_CTL(iface, (iface->writeNum + 1) << 6);
@@ -531,7 +520,6 @@ int bfin_twi_do_smbus_xfer(struct i2c_adapter *adap, u16 addr,
 		write_INT_MASK(iface, MCOMP | MERR |
 			((iface->read_write == I2C_SMBUS_READ) ?
 			RCVSERV : XMTSERV));
-		SSYNC();
 
 		/* Master enable */
 		write_MASTER_CTL(iface, read_MASTER_CTL(iface) | MEN |
@@ -539,7 +527,6 @@ int bfin_twi_do_smbus_xfer(struct i2c_adapter *adap, u16 addr,
 			((CONFIG_I2C_BLACKFIN_TWI_CLK_KHZ > 100) ? FAST : 0));
 		break;
 	}
-	SSYNC();
 
 	while (!iface->result) {
 		if (!wait_for_completion_timeout(&iface->complete,
@@ -669,7 +656,7 @@ static int i2c_bfin_twi_probe(struct platform_device *pdev)
 	strlcpy(p_adap->name, pdev->name, sizeof(p_adap->name));
 	p_adap->algo = &bfin_twi_algorithm;
 	p_adap->algo_data = iface;
-	p_adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
+	p_adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD | I2C_CLASS_DEPRECATED;
 	p_adap->dev.parent = &pdev->dev;
 	p_adap->timeout = 5 * HZ;
 	p_adap->retries = 3;
@@ -704,7 +691,6 @@ static int i2c_bfin_twi_probe(struct platform_device *pdev)
 
 	/* Enable TWI */
 	write_CONTROL(iface, read_CONTROL(iface) | TWI_ENA);
-	SSYNC();
 
 	rc = i2c_add_numbered_adapter(p_adap);
 	if (rc < 0) {
diff --git a/drivers/i2c/busses/i2c-cadence.c b/drivers/i2c/busses/i2c-cadence.c
new file mode 100644
index 00000000000..63f3f03ecc9
--- /dev/null
+++ b/drivers/i2c/busses/i2c-cadence.c
@@ -0,0 +1,905 @@
+/*
+ * I2C bus driver for the Cadence I2C controller.
+ *
+ * Copyright (C) 2009 - 2014 Xilinx, Inc.
+ *
+ * This program is free software; you can redistribute it
+ * and/or modify it under the terms of the GNU General Public
+ * License as published by the Free Software Foundation;
+ * either version 2 of the License, or (at your option) any
+ * later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+/* Register offsets for the I2C device. */
+#define CDNS_I2C_CR_OFFSET		0x00 /* Control Register, RW */
+#define CDNS_I2C_SR_OFFSET		0x04 /* Status Register, RO */
+#define CDNS_I2C_ADDR_OFFSET		0x08 /* I2C Address Register, RW */
+#define CDNS_I2C_DATA_OFFSET		0x0C /* I2C Data Register, RW */
+#define CDNS_I2C_ISR_OFFSET		0x10 /* IRQ Status Register, RW */
+#define CDNS_I2C_XFER_SIZE_OFFSET	0x14 /* Transfer Size Register, RW */
+#define CDNS_I2C_TIME_OUT_OFFSET	0x1C /* Time Out Register, RW */
+#define CDNS_I2C_IER_OFFSET		0x24 /* IRQ Enable Register, WO */
+#define CDNS_I2C_IDR_OFFSET		0x28 /* IRQ Disable Register, WO */
+
+/* Control Register Bit mask definitions */
+#define CDNS_I2C_CR_HOLD		BIT(4) /* Hold Bus bit */
+#define CDNS_I2C_CR_ACK_EN		BIT(3)
+#define CDNS_I2C_CR_NEA			BIT(2)
+#define CDNS_I2C_CR_MS			BIT(1)
+/* Read or Write Master transfer 0 = Transmitter, 1 = Receiver */
+#define CDNS_I2C_CR_RW			BIT(0)
+/* 1 = Auto init FIFO to zeroes */
+#define CDNS_I2C_CR_CLR_FIFO		BIT(6)
+#define CDNS_I2C_CR_DIVA_SHIFT		14
+#define CDNS_I2C_CR_DIVA_MASK		(3 << CDNS_I2C_CR_DIVA_SHIFT)
+#define CDNS_I2C_CR_DIVB_SHIFT		8
+#define CDNS_I2C_CR_DIVB_MASK		(0x3f << CDNS_I2C_CR_DIVB_SHIFT)
+
+/* Status Register Bit mask definitions */
+#define CDNS_I2C_SR_BA		BIT(8)
+#define CDNS_I2C_SR_RXDV	BIT(5)
+
+/*
+ * I2C Address Register Bit mask definitions
+ * Normal addressing mode uses [6:0] bits. Extended addressing mode uses [9:0]
+ * bits. A write access to this register always initiates a transfer if the I2C
+ * is in master mode.
+ */
+#define CDNS_I2C_ADDR_MASK	0x000003FF /* I2C Address Mask */
+
+/*
+ * I2C Interrupt Registers Bit mask definitions
+ * All the four interrupt registers (Status/Mask/Enable/Disable) have the same
+ * bit definitions.
+ */
+#define CDNS_I2C_IXR_ARB_LOST		BIT(9)
+#define CDNS_I2C_IXR_RX_UNF		BIT(7)
+#define CDNS_I2C_IXR_TX_OVF		BIT(6)
+#define CDNS_I2C_IXR_RX_OVF		BIT(5)
+#define CDNS_I2C_IXR_SLV_RDY		BIT(4)
+#define CDNS_I2C_IXR_TO			BIT(3)
+#define CDNS_I2C_IXR_NACK		BIT(2)
+#define CDNS_I2C_IXR_DATA		BIT(1)
+#define CDNS_I2C_IXR_COMP		BIT(0)
+
+#define CDNS_I2C_IXR_ALL_INTR_MASK	(CDNS_I2C_IXR_ARB_LOST | \
+					 CDNS_I2C_IXR_RX_UNF | \
+					 CDNS_I2C_IXR_TX_OVF | \
+					 CDNS_I2C_IXR_RX_OVF | \
+					 CDNS_I2C_IXR_SLV_RDY | \
+					 CDNS_I2C_IXR_TO | \
+					 CDNS_I2C_IXR_NACK | \
+					 CDNS_I2C_IXR_DATA | \
+					 CDNS_I2C_IXR_COMP)
+
+#define CDNS_I2C_IXR_ERR_INTR_MASK	(CDNS_I2C_IXR_ARB_LOST | \
+					 CDNS_I2C_IXR_RX_UNF | \
+					 CDNS_I2C_IXR_TX_OVF | \
+					 CDNS_I2C_IXR_RX_OVF | \
+					 CDNS_I2C_IXR_NACK)
+
+#define CDNS_I2C_ENABLED_INTR_MASK	(CDNS_I2C_IXR_ARB_LOST | \
+					 CDNS_I2C_IXR_RX_UNF | \
+					 CDNS_I2C_IXR_TX_OVF | \
+					 CDNS_I2C_IXR_RX_OVF | \
+					 CDNS_I2C_IXR_NACK | \
+					 CDNS_I2C_IXR_DATA | \
+					 CDNS_I2C_IXR_COMP)
+
+#define CDNS_I2C_TIMEOUT		msecs_to_jiffies(1000)
+
+#define CDNS_I2C_FIFO_DEPTH		16
+/* FIFO depth at which the DATA interrupt occurs */
+#define CDNS_I2C_DATA_INTR_DEPTH	(CDNS_I2C_FIFO_DEPTH - 2)
+#define CDNS_I2C_MAX_TRANSFER_SIZE	255
+/* Transfer size in multiples of data interrupt depth */
+#define CDNS_I2C_TRANSFER_SIZE	(CDNS_I2C_MAX_TRANSFER_SIZE - 3)
+
+#define DRIVER_NAME		"cdns-i2c"
+
+#define CDNS_I2C_SPEED_MAX	400000
+#define CDNS_I2C_SPEED_DEFAULT	100000
+
+#define CDNS_I2C_DIVA_MAX	4
+#define CDNS_I2C_DIVB_MAX	64
+
+#define cdns_i2c_readreg(offset)       readl_relaxed(id->membase + offset)
+#define cdns_i2c_writereg(val, offset) writel_relaxed(val, id->membase + offset)
+
+/**
+ * struct cdns_i2c - I2C device private data structure
+ * @membase:		Base address of the I2C device
+ * @adap:		I2C adapter instance
+ * @p_msg:		Message pointer
+ * @err_status:		Error status in Interrupt Status Register
+ * @xfer_done:		Transfer complete status
+ * @p_send_buf:		Pointer to transmit buffer
+ * @p_recv_buf:		Pointer to receive buffer
+ * @suspended:		Flag holding the device's PM status
+ * @send_count:		Number of bytes still expected to send
+ * @recv_count:		Number of bytes still expected to receive
+ * @irq:		IRQ number
+ * @input_clk:		Input clock to I2C controller
+ * @i2c_clk:		Maximum I2C clock speed
+ * @bus_hold_flag:	Flag used in repeated start for clearing HOLD bit
+ * @clk:		Pointer to struct clk
+ * @clk_rate_change_nb:	Notifier block for clock rate changes
+ */
+struct cdns_i2c {
+	void __iomem *membase;
+	struct i2c_adapter adap;
+	struct i2c_msg *p_msg;
+	int err_status;
+	struct completion xfer_done;
+	unsigned char *p_send_buf;
+	unsigned char *p_recv_buf;
+	u8 suspended;
+	unsigned int send_count;
+	unsigned int recv_count;
+	int irq;
+	unsigned long input_clk;
+	unsigned int i2c_clk;
+	unsigned int bus_hold_flag;
+	struct clk *clk;
+	struct notifier_block clk_rate_change_nb;
+};
+
+#define to_cdns_i2c(_nb)	container_of(_nb, struct cdns_i2c, \
+					     clk_rate_change_nb)
+
+/**
+ * cdns_i2c_clear_bus_hold() - Clear bus hold bit
+ * @id:	Pointer to driver data struct
+ *
+ * Helper to clear the controller's bus hold bit.
+ */
+static void cdns_i2c_clear_bus_hold(struct cdns_i2c *id)
+{
+	u32 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
+	if (reg & CDNS_I2C_CR_HOLD)
+		cdns_i2c_writereg(reg & ~CDNS_I2C_CR_HOLD, CDNS_I2C_CR_OFFSET);
+}
+
+/**
+ * cdns_i2c_isr - Interrupt handler for the I2C device
+ * @irq:	irq number for the I2C device
+ * @ptr:	void pointer to cdns_i2c structure
+ *
+ * This function handles the data interrupt, transfer complete interrupt and
+ * the error interrupts of the I2C device.
+ *
+ * Return: IRQ_HANDLED always
+ */
+static irqreturn_t cdns_i2c_isr(int irq, void *ptr)
+{
+	unsigned int isr_status, avail_bytes;
+	unsigned int bytes_to_recv, bytes_to_send;
+	struct cdns_i2c *id = ptr;
+	/* Signal completion only after everything is updated */
+	int done_flag = 0;
+	irqreturn_t status = IRQ_NONE;
+
+	isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
+
+	/* Handling nack and arbitration lost interrupt */
+	if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_ARB_LOST)) {
+		done_flag = 1;
+		status = IRQ_HANDLED;
+	}
+
+	/* Handling Data interrupt */
+	if ((isr_status & CDNS_I2C_IXR_DATA) &&
+			(id->recv_count >= CDNS_I2C_DATA_INTR_DEPTH)) {
+		/* Always read data interrupt threshold bytes */
+		bytes_to_recv = CDNS_I2C_DATA_INTR_DEPTH;
+		id->recv_count -= CDNS_I2C_DATA_INTR_DEPTH;
+		avail_bytes = cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
+
+		/*
+		 * if the tranfer size register value is zero, then
+		 * check for the remaining bytes and update the
+		 * transfer size register.
+		 */
+		if (!avail_bytes) {
+			if (id->recv_count > CDNS_I2C_TRANSFER_SIZE)
+				cdns_i2c_writere