Merge branch 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux

Pull i2c-embedded changes from Wolfram Sang:
 - CBUS driver (an I2C variant)
 - continued rework of the omap driver
 - s3c2410 gets lots of fixes and gains pinctrl support
 - at91 gains DMA support
 - the GPIO muxer gains devicetree probing
 - typical fixes and additions all over

* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
  i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
  i2c: at91: add dma support
  i2c: at91: change struct members indentation
  i2c: at91: fix compilation warning
  i2c: mxs: Do not disable the I2C SMBus quick mode
  i2c: mxs: Handle i2c DMA failure properly
  i2c: s3c2410: Remove recently introduced performance overheads
  i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
  i2c: s3c2410: Add fix for i2c suspend/resume
  i2c: s3c2410: Fix code to free gpios
  i2c: i2c-cbus-gpio: introduce driver
  i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
  i2c: ocores: Add irq support for sparc
  i2c: omap: Move the remove constraint
  ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
  i2c: s3c2410: do not special case HDMIPHY stuck bus detection
  i2c: s3c2410: use exponential back off while polling for bus idle
  i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
  i2c: s3c2410: grab adapter lock while changing i2c clock
  i2c: s3c2410: Add support for pinctrl
  ...

13 files changed, 1236 insertions, 337 deletions

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index c7bff51fe52..bdca5111eb9 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -337,6 +337,16 @@ config I2C_BLACKFIN_TWI_CLK_KHZ
 	help
 	  The unit of the TWI clock is kHz.
 
+config I2C_CBUS_GPIO
+	tristate "CBUS I2C driver"
+	depends on GENERIC_GPIO
+	help
+	  Support for CBUS access using I2C API. Mostly relevant for Nokia
+	  Internet Tablets (770, N800 and N810).
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called i2c-cbus-gpio.
+
 config I2C_CPM
 	tristate "Freescale CPM1 or CPM2 (MPC8xx/826x)"
 	depends on (CPM1 || CPM2) && OF_I2C
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index e5cb209d276..6181f3ff263 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -31,6 +31,7 @@ obj-$(CONFIG_I2C_POWERMAC)	+= i2c-powermac.o
 obj-$(CONFIG_I2C_AT91)		+= i2c-at91.o
 obj-$(CONFIG_I2C_AU1550)	+= i2c-au1550.o
 obj-$(CONFIG_I2C_BLACKFIN_TWI)	+= i2c-bfin-twi.o
+obj-$(CONFIG_I2C_CBUS_GPIO)	+= i2c-cbus-gpio.o
 obj-$(CONFIG_I2C_CPM)		+= i2c-cpm.o
 obj-$(CONFIG_I2C_DAVINCI)	+= i2c-davinci.o
 obj-$(CONFIG_I2C_DESIGNWARE_CORE)	+= i2c-designware-core.o
diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
index c02bf208084..b4575ee4bdf 100644
--- a/drivers/i2c/busses/i2c-at91.c
+++ b/drivers/i2c/busses/i2c-at91.c
@@ -19,6 +19,8 @@
 
 #include <linux/clk.h>
 #include <linux/completion.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
 #include <linux/err.h>
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
@@ -29,9 +31,11 @@
 #include <linux/of_i2c.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
+#include <linux/platform_data/dma-atmel.h>
 
 #define TWI_CLK_HZ		100000			/* max 400 Kbits/s */
 #define AT91_I2C_TIMEOUT	msecs_to_jiffies(100)	/* transfer timeout */
+#define AT91_I2C_DMA_THRESHOLD	8			/* enable DMA if transfer size is bigger than this threshold */
 
 /* AT91 TWI register definitions */
 #define	AT91_TWI_CR		0x0000	/* Control Register */
@@ -66,24 +70,39 @@
 #define	AT91_TWI_THR		0x0034	/* Transmit Holding Register */
 
 struct at91_twi_pdata {
-	unsigned	clk_max_div;
-	unsigned	clk_offset;
-	bool		has_unre_flag;
+	unsigned clk_max_div;
+	unsigned clk_offset;
+	bool has_unre_flag;
+	bool has_dma_support;
+	struct at_dma_slave dma_slave;
+};
+
+struct at91_twi_dma {
+	struct dma_chan *chan_rx;
+	struct dma_chan *chan_tx;
+	struct scatterlist sg;
+	struct dma_async_tx_descriptor *data_desc;
+	enum dma_data_direction direction;
+	bool buf_mapped;
+	bool xfer_in_progress;
 };
 
 struct at91_twi_dev {
-	struct device		*dev;
-	void __iomem		*base;
-	struct completion	cmd_complete;
-	struct clk		*clk;
-	u8			*buf;
-	size_t			buf_len;
-	struct i2c_msg		*msg;
-	int			irq;
-	unsigned		transfer_status;
-	struct i2c_adapter	adapter;
-	unsigned		twi_cwgr_reg;
-	struct at91_twi_pdata	*pdata;
+	struct device *dev;
+	void __iomem *base;
+	struct completion cmd_complete;
+	struct clk *clk;
+	u8 *buf;
+	size_t buf_len;
+	struct i2c_msg *msg;
+	int irq;
+	unsigned imr;
+	unsigned transfer_status;
+	struct i2c_adapter adapter;
+	unsigned twi_cwgr_reg;
+	struct at91_twi_pdata *pdata;
+	bool use_dma;
+	struct at91_twi_dma dma;
 };
 
 static unsigned at91_twi_read(struct at91_twi_dev *dev, unsigned reg)
@@ -102,6 +121,17 @@ static void at91_disable_twi_interrupts(struct at91_twi_dev *dev)
 		       AT91_TWI_TXCOMP | AT91_TWI_RXRDY | AT91_TWI_TXRDY);
 }
 
+static void at91_twi_irq_save(struct at91_twi_dev *dev)
+{
+	dev->imr = at91_twi_read(dev, AT91_TWI_IMR) & 0x7;
+	at91_disable_twi_interrupts(dev);
+}
+
+static void at91_twi_irq_restore(struct at91_twi_dev *dev)
+{
+	at91_twi_write(dev, AT91_TWI_IER, dev->imr);
+}
+
 static void at91_init_twi_bus(struct at91_twi_dev *dev)
 {
 	at91_disable_twi_interrupts(dev);
@@ -138,6 +168,28 @@ static void __devinit at91_calc_twi_clock(struct at91_twi_dev *dev, int twi_clk)
 	dev_dbg(dev->dev, "cdiv %d ckdiv %d\n", cdiv, ckdiv);
 }
 
+static void at91_twi_dma_cleanup(struct at91_twi_dev *dev)
+{
+	struct at91_twi_dma *dma = &dev->dma;
+
+	at91_twi_irq_save(dev);
+
+	if (dma->xfer_in_progress) {
+		if (dma->direction == DMA_FROM_DEVICE)
+			dmaengine_terminate_all(dma->chan_rx);
+		else
+			dmaengine_terminate_all(dma->chan_tx);
+		dma->xfer_in_progress = false;
+	}
+	if (dma->buf_mapped) {
+		dma_unmap_single(dev->dev, sg_dma_address(&dma->sg),
+				 dev->buf_len, dma->direction);
+		dma->buf_mapped = false;
+	}
+
+	at91_twi_irq_restore(dev);
+}
+
 static void at91_twi_write_next_byte(struct at91_twi_dev *dev)
 {
 	if (dev->buf_len <= 0)
@@ -154,6 +206,60 @@ static void at91_twi_write_next_byte(struct at91_twi_dev *dev)
 	++dev->buf;
 }
 
+static void at91_twi_write_data_dma_callback(void *data)
+{
+	struct at91_twi_dev *dev = (struct at91_twi_dev *)data;
+
+	dma_unmap_single(dev->dev, sg_dma_address(&dev->dma.sg),
+			 dev->buf_len, DMA_MEM_TO_DEV);
+
+	at91_twi_write(dev, AT91_TWI_CR, AT91_TWI_STOP);
+}
+
+static void at91_twi_write_data_dma(struct at91_twi_dev *dev)
+{
+	dma_addr_t dma_addr;
+	struct dma_async_tx_descriptor *txdesc;
+	struct at91_twi_dma *dma = &dev->dma;
+	struct dma_chan *chan_tx = dma->chan_tx;
+
+	if (dev->buf_len <= 0)
+		return;
+
+	dma->direction = DMA_TO_DEVICE;
+
+	at91_twi_irq_save(dev);
+	dma_addr = dma_map_single(dev->dev, dev->buf, dev->buf_len,
+				  DMA_TO_DEVICE);
+	if (dma_mapping_error(dev->dev, dma_addr)) {
+		dev_err(dev->dev, "dma map failed\n");
+		return;
+	}
+	dma->buf_mapped = true;
+	at91_twi_irq_restore(dev);
+	sg_dma_len(&dma->sg) = dev->buf_len;
+	sg_dma_address(&dma->sg) = dma_addr;
+
+	txdesc = dmaengine_prep_slave_sg(chan_tx, &dma->sg, 1, DMA_MEM_TO_DEV,
+					 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	if (!txdesc) {
+		dev_err(dev->dev, "dma prep slave sg failed\n");
+		goto error;
+	}
+
+	txdesc->callback = at91_twi_write_data_dma_callback;
+	txdesc->callback_param = dev;
+
+	dma->xfer_in_progress = true;
+	dmaengine_submit(txdesc);
+	dma_async_issue_pending(chan_tx);
+
+	return;
+
+error:
+	at91_twi_dma_cleanup(dev);
+}
+
 static void at91_twi_read_next_byte(struct at91_twi_dev *dev)
 {
 	if (dev->buf_len <= 0)
@@ -179,6 +285,61 @@ static void at91_twi_read_next_byte(struct at91_twi_dev *dev)
 	++dev->buf;
 }
 
+static void at91_twi_read_data_dma_callback(void *data)
+{
+	struct at91_twi_dev *dev = (struct at91_twi_dev *)data;
+
+	dma_unmap_single(dev->dev, sg_dma_address(&dev->dma.sg),
+			 dev->buf_len, DMA_DEV_TO_MEM);
+
+	/* The last two bytes have to be read without using dma */
+	dev->buf += dev->buf_len - 2;
+	dev->buf_len = 2;
+	at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_RXRDY);
+}
+
+static void at91_twi_read_data_dma(struct at91_twi_dev *dev)
+{
+	dma_addr_t dma_addr;
+	struct dma_async_tx_descriptor *rxdesc;
+	struct at91_twi_dma *dma = &dev->dma;
+	struct dma_chan *chan_rx = dma->chan_rx;
+
+	dma->direction = DMA_FROM_DEVICE;
+
+	/* Keep in mind that we won't use dma to read the last two bytes */
+	at91_twi_irq_save(dev);
+	dma_addr = dma_map_single(dev->dev, dev->buf, dev->buf_len - 2,
+				  DMA_FROM_DEVICE);
+	if (dma_mapping_error(dev->dev, dma_addr)) {
+		dev_err(dev->dev, "dma map failed\n");
+		return;
+	}
+	dma->buf_mapped = true;
+	at91_twi_irq_restore(dev);
+	dma->sg.dma_address = dma_addr;
+	sg_dma_len(&dma->sg) = dev->buf_len - 2;
+
+	rxdesc = dmaengine_prep_slave_sg(chan_rx, &dma->sg, 1, DMA_DEV_TO_MEM,
+					 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+	if (!rxdesc) {
+		dev_err(dev->dev, "dma prep slave sg failed\n");
+		goto error;
+	}
+
+	rxdesc->callback = at91_twi_read_data_dma_callback;
+	rxdesc->callback_param = dev;
+
+	dma->xfer_in_progress = true;
+	dmaengine_submit(rxdesc);
+	dma_async_issue_pending(dma->chan_rx);
+
+	return;
+
+error:
+	at91_twi_dma_cleanup(dev);
+}
+
 static irqreturn_t atmel_twi_interrupt(int irq, void *dev_id)
 {
 	struct at91_twi_dev *dev = dev_id;
@@ -229,12 +390,36 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev)
 		if (dev->buf_len <= 1 && !(dev->msg->flags & I2C_M_RECV_LEN))
 			start_flags |= AT91_TWI_STOP;
 		at91_twi_write(dev, AT91_TWI_CR, start_flags);
-		at91_twi_write(dev, AT91_TWI_IER,
+		/*
+		 * When using dma, the last byte has to be read manually in
+		 * order to not send the stop command too late and then
+		 * to receive extra data. In practice, there are some issues
+		 * if you use the dma to read n-1 bytes because of latency.
+		 * Reading n-2 bytes with dma and the two last ones manually
+		 * seems to be the best solution.
+		 */
+		if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) {
+			at91_twi_read_data_dma(dev);
+			/*
+			 * It is important to enable TXCOMP irq here because
+			 * doing it only when transferring the last two bytes
+			 * will mask NACK errors since TXCOMP is set when a
+			 * NACK occurs.
+			 */
+			at91_twi_write(dev, AT91_TWI_IER,
+			       AT91_TWI_TXCOMP);
+		} else
+			at91_twi_write(dev, AT91_TWI_IER,
 			       AT91_TWI_TXCOMP | AT91_TWI_RXRDY);
 	} else {
-		at91_twi_write_next_byte(dev);
-		at91_twi_write(dev, AT91_TWI_IER,
-			       AT91_TWI_TXCOMP | AT91_TWI_TXRDY);
+		if (dev->use_dma && (dev->buf_len > AT91_I2C_DMA_THRESHOLD)) {
+			at91_twi_write_data_dma(dev);
+			at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);
+		} else {
+			at91_twi_write_next_byte(dev);
+			at91_twi_write(dev, AT91_TWI_IER,
+				AT91_TWI_TXCOMP | AT91_TWI_TXRDY);
+		}
 	}
 
 	ret = wait_for_completion_interruptible_timeout(&dev->cmd_complete,
@@ -242,23 +427,31 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev)
 	if (ret == 0) {
 		dev_err(dev->dev, "controller timed out\n");
 		at91_init_twi_bus(dev);
-		return -ETIMEDOUT;
+		ret = -ETIMEDOUT;
+		goto error;
 	}
 	if (dev->transfer_status & AT91_TWI_NACK) {
 		dev_dbg(dev->dev, "received nack\n");
-		return -EREMOTEIO;
+		ret = -EREMOTEIO;
+		goto error;
 	}
 	if (dev->transfer_status & AT91_TWI_OVRE) {
 		dev_err(dev->dev, "overrun while reading\n");
-		return -EIO;
+		ret = -EIO;
+		goto error;
 	}
 	if (has_unre_flag && dev->transfer_status & AT91_TWI_UNRE) {
 		dev_err(dev->dev, "underrun while writing\n");
-		return -EIO;
+		ret = -EIO;
+		goto error;
 	}
 	dev_dbg(dev->dev, "transfer complete\n");
 
 	return 0;
+
+error:
+	at91_twi_dma_cleanup(dev);
+	return ret;
 }
 
 static int at91_twi_xfer(struct i2c_adapter *adap, struct i2c_msg *msg, int num)
@@ -329,36 +522,42 @@ static struct at91_twi_pdata at91rm9200_config = {
 	.clk_max_div = 5,
 	.clk_offset = 3,
 	.has_unre_flag = true,
+	.has_dma_support = false,
 };
 
 static struct at91_twi_pdata at91sam9261_config = {
 	.clk_max_div = 5,
 	.clk_offset = 4,
 	.has_unre_flag = false,
+	.has_dma_support = false,
 };
 
 static struct at91_twi_pdata at91sam9260_config = {
 	.clk_max_div = 7,
 	.clk_offset = 4,
 	.has_unre_flag = false,
+	.has_dma_support = false,
 };
 
 static struct at91_twi_pdata at91sam9g20_config = {
 	.clk_max_div = 7,
 	.clk_offset = 4,
 	.has_unre_flag = false,
+	.has_dma_support = false,
 };
 
 static struct at91_twi_pdata at91sam9g10_config = {
 	.clk_max_div = 7,
 	.clk_offset = 4,
 	.has_unre_flag = false,
+	.has_dma_support = false,
 };
 
 static struct at91_twi_pdata at91sam9x5_config = {
 	.clk_max_div = 7,
 	.clk_offset = 4,
 	.has_unre_flag = false,
+	.has_dma_support = true,
 };
 
 static const struct platform_device_id at91_twi_devtypes[] = {
@@ -405,6 +604,90 @@ MODULE_DEVICE_TABLE(of, atmel_twi_dt_ids);
 #define atmel_twi_dt_ids NULL
 #endif
 
+static bool __devinit filter(struct dma_chan *chan, void *slave)
+{
+	struct at_dma_slave *sl = slave;
+
+	if (sl->dma_dev == chan->device->dev) {
+		chan->private = sl;
+		return true;
+	} else {
+		return false;
+	}
+}
+
+static int __devinit at91_twi_configure_dma(struct at91_twi_dev *dev, u32 phy_addr)
+{
+	int ret = 0;
+	struct at_dma_slave *sdata;
+	struct dma_slave_config slave_config;
+	struct at91_twi_dma *dma = &dev->dma;
+
+	sdata = &dev->pdata->dma_slave;
+
+	memset(&slave_config, 0, sizeof(slave_config));
+	slave_config.src_addr = (dma_addr_t)phy_addr + AT91_TWI_RHR;
+	slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	slave_config.src_maxburst = 1;
+	slave_config.dst_addr = (dma_addr_t)phy_addr + AT91_TWI_THR;
+	slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	slave_config.dst_maxburst = 1;
+	slave_config.device_fc = false;
+
+	if (sdata && sdata->dma_dev) {
+		dma_cap_mask_t mask;
+
+		dma_cap_zero(mask);
+		dma_cap_set(DMA_SLAVE, mask);
+		dma->chan_tx = dma_request_channel(mask, filter, sdata);
+		if (!dma->chan_tx) {
+			dev_err(dev->dev, "no DMA channel available for tx\n");
+			ret = -EBUSY;
+			goto error;
+		}
+		dma->chan_rx = dma_request_channel(mask, filter, sdata);
+		if (!dma->chan_rx) {
+			dev_err(dev->dev, "no DMA channel available for rx\n");
+			ret = -EBUSY;
+			goto error;
+		}
+	} else {
+		ret = -EINVAL;
+		goto error;
+	}
+
+	slave_config.direction = DMA_MEM_TO_DEV;
+	if (dmaengine_slave_config(dma->chan_tx, &slave_config)) {
+		dev_err(dev->dev, "failed to configure tx channel\n");
+		ret = -EINVAL;
+		goto error;
+	}
+
+	slave_config.direction = DMA_DEV_TO_MEM;
+	if (dmaengine_slave_config(dma->chan_rx, &slave_config)) {
+		dev_err(dev->dev, "failed to configure rx channel\n");
+		ret = -EINVAL;
+		goto error;
+	}
+
+	sg_init_table(&dma->sg, 1);
+	dma->buf_mapped = false;
+	dma->xfer_in_progress = false;
+
+	dev_info(dev->dev, "using %s (tx) and %s (rx) for DMA transfers\n",
+		 dma_chan_name(dma->chan_tx), dma_chan_name(dma->chan_rx));
+
+	return ret;
+
+error:
+	dev_info(dev->dev, "can't use DMA\n");
+	if (dma->chan_rx)
+		dma_release_channel(dma->chan_rx);
+	if (dma->chan_tx)
+		dma_release_channel(dma->chan_tx);
+	return ret;
+}
+
 static struct at91_twi_pdata * __devinit at91_twi_get_driver_data(
 					struct platform_device *pdev)
 {
@@ -413,7 +696,7 @@ static struct at91_twi_pdata * __devinit at91_twi_get_driver_data(
 		match = of_match_node(atmel_twi_dt_ids, pdev->dev.of_node);
 		if (!match)
 			return NULL;
-		return match->data;
+		return (struct at91_twi_pdata *)match->data;
 	}
 	return (struct at91_twi_pdata *) platform_get_device_id(pdev)->driver_data;
 }
@@ -423,6 +706,7 @@ static int __devinit at91_twi_probe(struct platform_device *pdev)
 	struct at91_twi_dev *dev;
 	struct resource *mem;
 	int rc;
+	u32 phy_addr;
 
 	dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL);
 	if (!dev)
@@ -433,6 +717,7 @@ static int __devinit at91_twi_probe(struct platform_device *pdev)
 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!mem)
 		return -ENODEV;
+	phy_addr = mem->start;
 
 	dev->pdata = at91_twi_get_driver_data(pdev);
 	if (!dev->pdata)
@@ -462,6 +747,11 @@ static int __devinit at91_twi_probe(struct platform_device *pdev)
 	}
 	clk_prepare_enable(dev->clk);
 
+	if (dev->pdata->has_dma_support) {
+		if (at91_twi_configure_dma(dev, phy_addr) == 0)
+			dev->use_dma = true;
+	}
+
 	at91_calc_twi_clock(dev, TWI_CLK_HZ);
 	at91_init_twi_bus(dev);
 
diff --git a/drivers/i2c/busses/i2c-cbus-gpio.c b/drivers/i2c/busses/i2c-cbus-gpio.c
new file mode 100644
index 00000000000..98386d65931
--- /dev/null
+++ b/drivers/i2c/busses/i2c-cbus-gpio.c
@@ -0,0 +1,300 @@
+/*
+ * CBUS I2C driver for Nokia Internet Tablets.
+ *
+ * Copyright (C) 2004-2010 Nokia Corporation
+ *
+ * Based on code written by Juha Yrjölä, David Weinehall, Mikko Ylinen and
+ * Felipe Balbi. Converted to I2C driver by Aaro Koskinen.
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_gpio.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/platform_data/i2c-cbus-gpio.h>
+
+/*
+ * Bit counts are derived from Nokia implementation. These should be checked
+ * if other CBUS implementations appear.
+ */
+#define CBUS_ADDR_BITS	3
+#define CBUS_REG_BITS	5
+
+struct cbus_host {
+	spinlock_t	lock;		/* host lock */
+	struct device	*dev;
+	int		clk_gpio;
+	int		dat_gpio;
+	int		sel_gpio;
+};
+
+/**
+ * cbus_send_bit - sends one bit over the bus
+ * @host: the host we're using
+ * @bit: one bit of information to send
+ */
+static void cbus_send_bit(struct cbus_host *host, unsigned bit)
+{
+	gpio_set_value(host->dat_gpio, bit ? 1 : 0);
+	gpio_set_value(host->clk_gpio, 1);
+	gpio_set_value(host->clk_gpio, 0);
+}
+
+/**
+ * cbus_send_data - sends @len amount of data over the bus
+ * @host: the host we're using
+ * @data: the data to send
+ * @len: size of the transfer
+ */
+static void cbus_send_data(struct cbus_host *host, unsigned data, unsigned len)
+{
+	int i;
+
+	for (i = len; i > 0; i--)
+		cbus_send_bit(host, data & (1 << (i - 1)));
+}
+
+/**
+ * cbus_receive_bit - receives one bit from the bus
+ * @host: the host we're using
+ */
+static int cbus_receive_bit(struct cbus_host *host)
+{
+	int ret;
+
+	gpio_set_value(host->clk_gpio, 1);
+	ret = gpio_get_value(host->dat_gpio);
+	gpio_set_value(host->clk_gpio, 0);
+	return ret;
+}
+
+/**
+ * cbus_receive_word - receives 16-bit word from the bus
+ * @host: the host we're using
+ */
+static int cbus_receive_word(struct cbus_host *host)
+{
+	int ret = 0;
+	int i;
+
+	for (i = 16; i > 0; i--) {
+		int bit = cbus_receive_bit(host);
+
+		if (bit < 0)
+			return bit;
+
+		if (bit)
+			ret |= 1 << (i - 1);
+	}
+	return ret;
+}
+
+/**
+ * cbus_transfer - transfers data over the bus
+ * @host: the host we're using
+ * @rw: read/write flag
+ * @dev: device address
+ * @reg: register address
+ * @data: if @rw == I2C_SBUS_WRITE data to send otherwise 0
+ */
+static int cbus_transfer(struct cbus_host *host, char rw, unsigned dev,
+			 unsigned reg, unsigned data)
+{
+	unsigned long flags;
+	int ret;
+
+	/* We don't want interrupts disturbing our transfer */
+	spin_lock_irqsave(&host->lock, flags);
+
+	/* Reset state and start of transfer, SEL stays down during transfer */
+	gpio_set_value(host->sel_gpio, 0);
+
+	/* Set the DAT pin to output */
+	gpio_direction_output(host->dat_gpio, 1);
+
+	/* Send the device address */
+	cbus_send_data(host, dev, CBUS_ADDR_BITS);
+
+	/* Send the rw flag */
+	cbus_send_bit(host, rw == I2C_SMBUS_READ);
+
+	/* Send the register address */
+	cbus_send_data(host, reg, CBUS_REG_BITS);
+
+	if (rw == I2C_SMBUS_WRITE) {
+		cbus_send_data(host, data, 16);
+		ret = 0;
+	} else {
+		ret = gpio_direction_input(host->dat_gpio);
+		if (ret) {
+			dev_dbg(host->dev, "failed setting direction\n");
+			goto out;
+		}
+		gpio_set_value(host->clk_gpio, 1);
+
+		ret = cbus_receive_word(host);
+		if (ret < 0) {
+			dev_dbg(host->dev, "failed receiving data\n");
+			goto out;
+		}
+	}
+
+	/* Indicate end of transfer, SEL goes up until next transfer */
+	gpio_set_value(host->sel_gpio, 1);
+	gpio_set_value(host->clk_gpio, 1);
+	gpio_set_value(host->clk_gpio, 0);
+
+out:
+	spin_unlock_irqrestore(&host->lock, flags);
+
+	return ret;
+}
+
+static int cbus_i2c_smbus_xfer(struct i2c_adapter	*adapter,
+			       u16			addr,
+			       unsigned short		flags,
+			       char			read_write,
+			       u8			command,
+			       int			size,
+			       union i2c_smbus_data	*data)
+{
+	struct cbus_host *chost = i2c_get_adapdata(adapter);
+	int ret;
+
+	if (size != I2C_SMBUS_WORD_DATA)
+		return -EINVAL;
+
+	ret = cbus_transfer(chost, read_write == I2C_SMBUS_READ, addr,
+			    command, data->word);
+	if (ret < 0)
+		return ret;
+
+	if (read_write == I2C_SMBUS_READ)
+		data->word = ret;
+
+	return 0;
+}
+
+static u32 cbus_i2c_func(struct i2c_adapter *adapter)
+{
+	return I2C_FUNC_SMBUS_READ_WORD_DATA | I2C_FUNC_SMBUS_WRITE_WORD_DATA;
+}
+
+static const struct i2c_algorithm cbus_i2c_algo = {
+	.smbus_xfer	= cbus_i2c_smbus_xfer,
+	.functionality	= cbus_i2c_func,
+};
+
+static int cbus_i2c_remove(struct platform_device *pdev)
+{
+	struct i2c_adapter *adapter = platform_get_drvdata(pdev);
+
+	return i2c_del_adapter(adapter);
+}
+
+static int cbus_i2c_probe(struct platform_device *pdev)
+{
+	struct i2c_adapter *adapter;
+	struct cbus_host *chost;
+	int ret;
+
+	adapter = devm_kzalloc(&pdev->dev, sizeof(struct i2c_adapter),
+			       GFP_KERNEL);
+	if (!adapter)
+		return -ENOMEM;
+
+	chost = devm_kzalloc(&pdev->dev, sizeof(*chost), GFP_KERNEL);
+	if (!chost)
+		return -ENOMEM;
+
+	if (pdev->dev.of_node) {
+		struct device_node *dnode = pdev->dev.of_node;
+		if (of_gpio_count(dnode) != 3)
+			return -ENODEV;
+		chost->clk_gpio = of_get_gpio(dnode, 0);
+		chost->dat_gpio = of_get_gpio(dnode, 1);
+		chost->sel_gpio = of_get_gpio(dnode, 2);
+	} else if (pdev->dev.platform_data) {
+		struct i2c_cbus_platform_data *pdata = pdev->dev.platform_data;
+		chost->clk_gpio = pdata->clk_gpio;
+		chost->dat_gpio = pdata->dat_gpio;
+		chost->sel_gpio = pdata->sel_gpio;
+	} else {
+		return -ENODEV;
+	}
+
+	adapter->owner		= THIS_MODULE;
+	adapter->class		= I2C_CLASS_HWMON;
+	adapter->dev.parent	= &pdev->dev;
+	adapter->nr		= pdev->id;
+	adapter->timeout	= HZ;
+	adapter->algo		= &cbus_i2c_algo;
+	strlcpy(adapter->name, "CBUS I2C adapter", sizeof(adapter->name));
+
+	spin_lock_init(&chost->lock);
+	chost->dev = &pdev->dev;
+
+	ret = devm_gpio_request_one(&pdev->dev, chost->clk_gpio,
+				    GPIOF_OUT_INIT_LOW, "CBUS clk");
+	if (ret)
+		return ret;
+
+	ret = devm_gpio_request_one(&pdev->dev, chost->dat_gpio, GPIOF_IN,
+				    "CBUS data");
+	if (ret)
+		return ret;
+
+	ret = devm_gpio_request_one(&pdev->dev, chost->sel_gpio,
+				    GPIOF_OUT_INIT_HIGH, "CBUS sel");
+	if (ret)
+		return ret;
+
+	i2c_set_adapdata(adapter, chost);
+	platform_set_drvdata(pdev, adapter);
+
+	return i2c_add_numbered_adapter(adapter);
+}
+
+#if defined(CONFIG_OF)
+static const struct of_device_id i2c_cbus_dt_ids[] = {
+	{ .compatible = "i2c-cbus-gpio", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, i2c_cbus_dt_ids);
+#endif
+
+static struct platform_driver cbus_i2c_driver = {
+	.probe	= cbus_i2c_probe,
+	.remove	= cbus_i2c_remove,
+	.driver	= {
+		.owner	= THIS_MODULE,
+		.name	= "i2c-cbus-gpio",
+	},
+};
+module_platform_driver(cbus_i2c_driver);
+
+MODULE_ALIAS("platform:i2c-cbus-gpio");
+MODULE_DESCRIPTION("CBUS I2C driver");
+MODULE_AUTHOR("Juha Yrjölä");
+MODULE_AUTHOR("David Weinehall");
+MODULE_AUTHOR("Mikko Ylinen");
+MODULE_AUTHOR("Felipe Balbi");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/i2c/busses/i2c-gpio.c b/drivers/i2c/busses/i2c-gpio.c
index e62d2d93862..257299a92df 100644
--- a/drivers/i2c/busses/i2c-gpio.c
+++ b/drivers/i2c/busses/i2c-gpio.c
@@ -184,7 +184,11 @@ static int __devinit i2c_gpio_probe(struct platform_device *pdev)
 	bit_data->data = pdata;
 
 	adap->owner = THIS_MODULE;
-	snprintf(adap->name, sizeof(adap->name), "i2c-gpio%d", pdev->id);
+	if (pdev->dev.of_node)
+		strlcpy(adap->name, dev_name(&pdev->dev), sizeof(adap->name));
+	else
+		snprintf(adap->name, sizeof(adap->name), "i2c-gpio%d", pdev->id);
+
 	adap->algo_data = bit_data;
 	adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD;
 	adap->dev.parent = &pdev->dev;
diff --git a/drivers/i2c/busses/i2c-mxs.c b/drivers/i2c/busses/i2c-mxs.c
index 0670da79ee5..6ed53da9e1f 100644
--- a/drivers/i2c/busses/i2c-mxs.c
+++ b/drivers/i2c/busses/i2c-mxs.c
@@ -359,7 +359,7 @@ static int mxs_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[],
 
 static u32 mxs_i2c_func(struct i2c_adapter *adap)
 {
-	return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK);
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
 }
 
 static irqreturn_t mxs_i2c_isr(int this_irq, void *dev_id)
diff --git a/drivers/i2c/busses/i2c-nomadik.c b/drivers/i2c/busses/i2c-nomadik.c
index 02c3115a2df..8b2ffcf4532 100644
--- a/drivers/i2c/busses/i2c-nomadik.c
+++ b/drivers/i2c/busses/i2c-nomadik.c
@@ -435,13 +435,6 @@ static int read_i2c(struct nmk_i2c_dev *dev, u16 flags)
 	timeout = wait_for_completion_timeout(
 		&dev->xfer_complete, dev->adap.timeout);
 
-	if (timeout < 0) {
-		dev_err(&dev->adev->dev,
-			"wait_for_completion_timeout "
-			"returned %d waiting for event\n", timeout);
-		status = timeout;
-	}
-
 	if (timeout == 0) {
 		/* Controller timed out */
 		dev_err(&dev->adev->dev, "read from slave 0x%x timed out\n",
@@ -523,13 +516,6 @@ static int write_i2c(struct nmk_i2c_dev *dev, u16 flags)
 	timeout = wait_for_completion_timeout(
 		&dev->xfer_complete, dev->adap.timeout);
 
-	if (timeout < 0) {
-		dev_err(&dev->adev->dev,
-			"wait_for_completion_timeout "
-			"returned %d waiting for event\n", timeout);
-		status = timeout;
-	}
-
 	if (timeout == 0) {
 		/* Controller timed out */
 		dev_err(&dev->adev->dev, "write to slave 0x%x timed out\n",
diff --git a/drivers/i2c/busses/i2c-ocores.c b/drivers/i2c/busses/i2c-ocores.c
index 15da1ac7cf9..9b35c9fbb2f 100644
--- a/drivers/i2c/busses/i2c-ocores.c
+++ b/drivers/i2c/busses/i2c-ocores.c
@@ -4,6 +4,9 @@
  *
  * Peter Korsgaard <jacmet@sunsite.dk>
  *
+ * Support for the GRLIB port of the controller by
+ * Andreas Larsson <andreas@gaisler.com>
+ *
  * This file is licensed under the terms of the GNU General Public License
  * version 2.  This program is licensed "as is" without any warranty of any
  * kind, whether express or implied.
@@ -34,6 +37,8 @@ struct ocores_i2c {
 	int nmsgs;
 	int state; /* see STATE_ */
 	int clock_khz;
+	void (*setreg)(struct ocores_i2c *i2c, int reg, u8 value);
+	u8 (*getreg)(struct ocores_i2c *i2c, int reg);
 };
 
 /* registers */
@@ -67,24 +72,47 @@ struct ocores_i2c {
 #define STATE_READ		3
 #define STATE_ERROR		4
 
+#define TYPE_OCORES		0
+#define TYPE_GRLIB		1
+
+static void oc_setreg_8(struct ocores_i2c *i2c, int reg, u8 value)
+{
+	iowrite8(value, i2c->base + (reg << i2c->reg_shift));
+}
+
+static void oc_setreg_16(struct ocores_i2c *i2c, int reg, u8 value)
+{
+	iowrite16(value, i2c->base + (reg << i2c->reg_shift));
+}
+
+static void oc_setreg_32(struct ocores_i2c *i2c, int reg, u8 value)
+{
+	iowrite32(value, i2c->base + (reg << i2c->reg_shift));
+}
+
+static inline u8 oc_getreg_8(struct ocores_i2c *i2c, int reg)
+{
+	return ioread8(i2c->base + (reg << i2c->reg_shift));
+}
+
+static inline u8 oc_getreg_16(struct ocores_i2c *i2c, int reg)
+{
+	return ioread16(i2c->base + (reg << i2c->reg_shift));
+}
+
+static inline u8 oc_getreg_32(struct ocores_i2c *i2c, int reg)
+{
+	return ioread32(i2c->base + (reg << i2c->reg_shift));
+}
+
 static inline void oc_setreg(struct ocores_i2c *i2c, int reg, u8 value)
 {
-	if (i2c->reg_io_width == 4)
-		iowrite32(value, i2c->base + (reg << i2c->reg_shift));
-	else if (i2c->reg_io_width == 2)
-		iowrite16(value, i2c->base + (reg << i2c->reg_shift));
-	else
-		iowrite8(value, i2c->base + (reg << i2c->reg_shift));
+	i2c->setreg(i2c, reg, value);
 }
 
 static inline u8 oc_getreg(struct ocores_i2c *i2c, int reg)
 {
-	if (i2c->reg_io_width == 4)
-		return ioread32(i2c->base + (reg << i2c->reg_shift));
-	else if (i2c->reg_io_width == 2)
-		return ioread16(i2c->base + (reg << i2c->reg_shift));
-	else
-		return ioread8(i2c->base + (reg << i2c->reg_shift));
+	return i2c->getreg(i2c, reg);
 }
 
 static void ocores_process(struct ocores_i2c *i2c)
@@ -223,11 +251,59 @@ static struct i2c_adapter ocores_adapter = {
 	.algo		= &ocores_algorithm,
 };
 
+static struct of_device_id ocores_i2c_match[] = {
+	{
+		.compatible = "opencores,i2c-ocores",