Add support for GMT G762/G763 PWM fan controllers

GMT G762/763 fan speed PWM controller is connected directly to a fan
and performs closed-loop or open-loop control of the fan speed. Two
modes - PWM or DC - are supported by the chip. Introduced driver
provides various knobs to control the operations of the chip (via
sysfs interface). Specific characteristics of the system can be passed
either using board init code or via DT. Documentation for both the
driver and DT bindings are also provided.

Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

3 files changed, 1160 insertions, 0 deletions

diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index 683c769a8fc..e989f7fd645 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -461,6 +461,16 @@ config SENSORS_G760A
 	  This driver can also be built as a module.  If so, the module
 	  will be called g760a.
 
+config SENSORS_G762
+	tristate "GMT G762 and G763"
+	depends on I2C
+	help
+	  If you say yes here you get support for Global Mixed-mode
+	  Technology Inc G762 and G763 fan speed PWM controller chips.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called g762.
+
 config SENSORS_GL518SM
 	tristate "Genesys Logic GL518SM"
 	depends on I2C
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index d17d3e64f9f..4f0fb5235f4 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -60,6 +60,7 @@ obj-$(CONFIG_SENSORS_F75375S)	+= f75375s.o
 obj-$(CONFIG_SENSORS_FAM15H_POWER) += fam15h_power.o
 obj-$(CONFIG_SENSORS_FSCHMD)	+= fschmd.o
 obj-$(CONFIG_SENSORS_G760A)	+= g760a.o
+obj-$(CONFIG_SENSORS_G762)	+= g762.o
 obj-$(CONFIG_SENSORS_GL518SM)	+= gl518sm.o
 obj-$(CONFIG_SENSORS_GL520SM)	+= gl520sm.o
 obj-$(CONFIG_SENSORS_GPIO_FAN)	+= gpio-fan.o
diff --git a/drivers/hwmon/g762.c b/drivers/hwmon/g762.c
new file mode 100644
index 00000000000..73adf01b0ef
--- /dev/null
+++ b/drivers/hwmon/g762.c
@@ -0,0 +1,1149 @@
+/*
+ * g762 - Driver for the Global Mixed-mode Technology Inc. fan speed
+ *        PWM controller chips from G762 family, i.e. G762 and G763
+ *
+ * Copyright (C) 2013, Arnaud EBALARD <arno@natisbad.org>
+ *
+ * This work is based on a basic version for 2.6.31 kernel developed
+ * by Olivier Mouchet for LaCie. Updates and correction have been
+ * performed to run on recent kernels. Additional features, like the
+ * ability to configure various characteristics via .dts file or
+ * board init file have been added. Detailed datasheet on which this
+ * development is based is available here:
+ *
+ *  http://natisbad.org/NAS/refs/GMT_EDS-762_763-080710-0.2.pdf
+ *
+ * Headers from previous developments have been kept below:
+ *
+ * Copyright (c) 2009 LaCie
+ *
+ * Author: Olivier Mouchet <olivier.mouchet@gmail.com>
+ *
+ * based on g760a code written by Herbert Valerio Riedel <hvr@gnu.org>
+ * Copyright (C) 2007  Herbert Valerio Riedel <hvr@gnu.org>
+ *
+ * g762: minimal datasheet available at:
+ *       http://www.gmt.com.tw/product/datasheet/EDS-762_3.pdf
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation.
+ */
+
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/jiffies.h>
+#include <linux/i2c.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/err.h>
+#include <linux/mutex.h>
+#include <linux/kernel.h>
+#include <linux/clk.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_data/g762.h>
+
+#define DRVNAME "g762"
+
+static const struct i2c_device_id g762_id[] = {
+	{ "g762", 0 },
+	{ "g763", 0 },
+	{ }
+};
+MODULE_DEVICE_TABLE(i2c, g762_id);
+
+enum g762_regs {
+	G762_REG_SET_CNT  = 0x00,
+	G762_REG_ACT_CNT  = 0x01,
+	G762_REG_FAN_STA  = 0x02,
+	G762_REG_SET_OUT  = 0x03,
+	G762_REG_FAN_CMD1 = 0x04,
+	G762_REG_FAN_CMD2 = 0x05,
+};
+
+/* Config register bits */
+#define G762_REG_FAN_CMD1_DET_FAN_FAIL  0x80 /* enable fan_fail signal */
+#define G762_REG_FAN_CMD1_DET_FAN_OOC   0x40 /* enable fan_out_of_control */
+#define G762_REG_FAN_CMD1_OUT_MODE      0x20 /* out mode: PWM or DC */
+#define G762_REG_FAN_CMD1_FAN_MODE      0x10 /* fan mode: closed/open-loop */
+#define G762_REG_FAN_CMD1_CLK_DIV_ID1   0x08 /* clock divisor value */
+#define G762_REG_FAN_CMD1_CLK_DIV_ID0   0x04
+#define G762_REG_FAN_CMD1_PWM_POLARITY  0x02 /* PWM polarity */
+#define G762_REG_FAN_CMD1_PULSE_PER_REV 0x01 /* pulse per fan revolution */
+
+#define G762_REG_FAN_CMD2_GEAR_MODE_1   0x08 /* fan gear mode */
+#define G762_REG_FAN_CMD2_GEAR_MODE_0   0x04
+#define G762_REG_FAN_CMD2_FAN_STARTV_1  0x02 /* fan startup voltage */
+#define G762_REG_FAN_CMD2_FAN_STARTV_0  0x01
+
+#define G762_REG_FAN_STA_FAIL           0x02 /* fan fail */
+#define G762_REG_FAN_STA_OOC            0x01 /* fan out of control */
+
+/* Config register values */
+#define G762_OUT_MODE_PWM            1
+#define G762_OUT_MODE_DC             0
+
+#define G762_FAN_MODE_CLOSED_LOOP    2
+#define G762_FAN_MODE_OPEN_LOOP      1
+
+#define G762_PWM_POLARITY_NEGATIVE   1
+#define G762_PWM_POLARITY_POSITIVE   0
+
+/* Register data is read (and cached) at most once per second. */
+#define G762_UPDATE_INTERVAL    HZ
+
+/*
+ * Extract pulse count per fan revolution value (2 or 4) from given
+ * FAN_CMD1 register value.
+ */
+#define G762_PULSE_FROM_REG(reg) \
+	((((reg) & G762_REG_FAN_CMD1_PULSE_PER_REV) + 1) << 1)
+
+/*
+ * Extract fan clock divisor (1, 2, 4 or 8) from given FAN_CMD1
+ * register value.
+ */
+#define G762_CLKDIV_FROM_REG(reg) \
+	(1 << (((reg) & (G762_REG_FAN_CMD1_CLK_DIV_ID0 |	\
+			 G762_REG_FAN_CMD1_CLK_DIV_ID1)) >> 2))
+
+/*
+ * Extract fan gear mode multiplier value (0, 2 or 4) from given
+ * FAN_CMD2 register value.
+ */
+#define G762_GEARMULT_FROM_REG(reg) \
+	(1 << (((reg) & (G762_REG_FAN_CMD2_GEAR_MODE_0 |	\
+			 G762_REG_FAN_CMD2_GEAR_MODE_1)) >> 2))
+
+struct g762_data {
+	struct i2c_client *client;
+	struct device *hwmon_dev;
+	struct clk *clk;
+
+	/* update mutex */
+	struct mutex update_lock;
+
+	/* board specific parameters. */
+	u32 clk_freq;
+
+	/* g762 register cache */
+	bool valid;
+	unsigned long last_updated; /* in jiffies */
+
+	u8 set_cnt;  /* controls fan rotation speed in closed-loop mode */
+	u8 act_cnt;  /* provides access to current fan RPM value */
+	u8 fan_sta;  /* bit 0: set when actual fan speed is more than
+		      *        25% outside requested fan speed
+		      * bit 1: set when no transition occurs on fan
+		      *        pin for 0.7s
+		      */
+	u8 set_out;  /* controls fan rotation speed in open-loop mode */
+	u8 fan_cmd1; /*   0: FG_PLS_ID0 FG pulses count per revolution
+		      *      0: 2 counts per revolution
+		      *      1: 4 counts per revolution
+		      *   1: PWM_POLARITY 1: negative_duty
+		      *                   0: positive_duty
+		      * 2,3: [FG_CLOCK_ID0, FG_CLK_ID1]
+		      *         00: Divide fan clock by 1
+		      *         01: Divide fan clock by 2
+		      *         10: Divide fan clock by 4
+		      *         11: Divide fan clock by 8
+		      *   4: FAN_MODE 1:closed-loop, 0:open-loop
+		      *   5: OUT_MODE 1:PWM, 0:DC
+		      *   6: DET_FAN_OOC enable "fan ooc" status
+		      *   7: DET_FAN_FAIL enable "fan fail" status
+		      */
+	u8 fan_cmd2; /* 0,1: FAN_STARTV 0,1,2,3 -> 0,32,64,96 dac_code
+		      * 2,3: FG_GEAR_MODE
+		      *         00: multiplier = 1
+		      *         01: multiplier = 2
+		      *         10: multiplier = 4
+		      *   4: Mask ALERT# (g763 only)
+		      */
+};
+
+/*
+ * Convert count value from fan controller register (FAN_SET_CNT) into fan
+ * speed RPM value. Note that the datasheet documents a basic formula;
+ * influence of additional parameters (fan clock divisor, fan gear mode)
+ * have been infered from examples in the datasheet and tests.
+ */
+static inline unsigned int rpm_from_cnt(u8 cnt, u32 clk_freq, u16 p,
+					u8 clk_div, u8 gear_mult)
+{
+	if (cnt == 0xff)  /* setting cnt to 255 stops the fan */
+		return 0;
+
+	return (clk_freq * 30 * gear_mult) / ((cnt ? cnt : 1) * p * clk_div);
+}
+
+/*
+ * Convert fan RPM value from sysfs into count value for fan controller
+ * register (FAN_SET_CNT).
+ */
+static inline unsigned char cnt_from_rpm(u32 rpm, u32 clk_freq, u16 p,
+					 u8 clk_div, u8 gear_mult)
+{
+	if (!rpm)         /* to stop the fan, set cnt to 255 */
+		return 0xff;
+
+	return clamp_val(((clk_freq * 30 * gear_mult) / (rpm * p * clk_div)),
+			 0, 255);
+}
+
+/* helper to grab and cache data, at most one time per second */
+static struct g762_data *g762_update_client(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = i2c_get_clientdata(client);
+	int ret = 0;
+
+	mutex_lock(&data->update_lock);
+	if (time_before(jiffies, data->last_updated + G762_UPDATE_INTERVAL) &&
+	    likely(data->valid))
+		goto out;
+
+	ret = i2c_smbus_read_byte_data(client, G762_REG_SET_CNT);
+	if (ret < 0)
+		goto out;
+	data->set_cnt = ret;
+
+	ret = i2c_smbus_read_byte_data(client, G762_REG_ACT_CNT);
+	if (ret < 0)
+		goto out;
+	data->act_cnt = ret;
+
+	ret = i2c_smbus_read_byte_data(client, G762_REG_FAN_STA);
+	if (ret < 0)
+		goto out;
+	data->fan_sta = ret;
+
+	ret = i2c_smbus_read_byte_data(client, G762_REG_SET_OUT);
+	if (ret < 0)
+		goto out;
+	data->set_out = ret;
+
+	ret = i2c_smbus_read_byte_data(client, G762_REG_FAN_CMD1);
+	if (ret < 0)
+		goto out;
+	data->fan_cmd1 = ret;
+
+	ret = i2c_smbus_read_byte_data(client, G762_REG_FAN_CMD2);
+	if (ret < 0)
+		goto out;
+	data->fan_cmd2 = ret;
+
+	data->last_updated = jiffies;
+	data->valid = true;
+ out:
+	mutex_unlock(&data->update_lock);
+
+	if (ret < 0) /* upon error, encode it in return value */
+		data = ERR_PTR(ret);
+
+	return data;
+}
+
+/* helpers for writing hardware parameters */
+
+/*
+ * Set input clock frequency received on CLK pin of the chip. Accepted values
+ * are between 0 and 0xffffff. If zero is given, then default frequency
+ * (32,768Hz) is used. Note that clock frequency is a characteristic of the
+ * system but an internal parameter, i.e. value is not passed to the device.
+ */
+static int do_set_clk_freq(struct device *dev, unsigned long val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = i2c_get_clientdata(client);
+
+	if (val > 0xffffff)
+		return -EINVAL;
+	if (!val)
+		val = 32768;
+
+	data->clk_freq = val;
+
+	return 0;
+}
+
+/* Set pwm mode. Accepts either 0 (PWM mode) or 1 (DC mode) */
+static int do_set_pwm_mode(struct device *dev, unsigned long val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = g762_update_client(dev);
+	int ret;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	mutex_lock(&data->update_lock);
+	switch (val) {
+	case G762_OUT_MODE_PWM:
+		data->fan_cmd1 |=  G762_REG_FAN_CMD1_OUT_MODE;
+		break;
+	case G762_OUT_MODE_DC:
+		data->fan_cmd1 &= ~G762_REG_FAN_CMD1_OUT_MODE;
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+	ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+					data->fan_cmd1);
+	data->valid = false;
+ out:
+	mutex_unlock(&data->update_lock);
+
+	return ret;
+}
+
+/* Set fan clock divisor. Accepts either 1, 2, 4 or 8. */
+static int do_set_fan_div(struct device *dev, unsigned long val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = g762_update_client(dev);
+	int ret;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	mutex_lock(&data->update_lock);
+	switch (val) {
+	case 1:
+		data->fan_cmd1 &= ~G762_REG_FAN_CMD1_CLK_DIV_ID0;
+		data->fan_cmd1 &= ~G762_REG_FAN_CMD1_CLK_DIV_ID1;
+		break;
+	case 2:
+		data->fan_cmd1 |=  G762_REG_FAN_CMD1_CLK_DIV_ID0;
+		data->fan_cmd1 &= ~G762_REG_FAN_CMD1_CLK_DIV_ID1;
+		break;
+	case 4:
+		data->fan_cmd1 &= ~G762_REG_FAN_CMD1_CLK_DIV_ID0;
+		data->fan_cmd1 |=  G762_REG_FAN_CMD1_CLK_DIV_ID1;
+		break;
+	case 8:
+		data->fan_cmd1 |=  G762_REG_FAN_CMD1_CLK_DIV_ID0;
+		data->fan_cmd1 |=  G762_REG_FAN_CMD1_CLK_DIV_ID1;
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+	ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+					data->fan_cmd1);
+	data->valid = false;
+ out:
+	mutex_unlock(&data->update_lock);
+
+	return ret;
+}
+
+/* Set fan gear mode. Accepts either 0, 1 or 2. */
+static int do_set_fan_gear_mode(struct device *dev, unsigned long val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = g762_update_client(dev);
+	int ret;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	mutex_lock(&data->update_lock);
+	switch (val) {
+	case 0:
+		data->fan_cmd2 &= ~G762_REG_FAN_CMD2_GEAR_MODE_0;
+		data->fan_cmd2 &= ~G762_REG_FAN_CMD2_GEAR_MODE_1;
+		break;
+	case 1:
+		data->fan_cmd2 |=  G762_REG_FAN_CMD2_GEAR_MODE_0;
+		data->fan_cmd2 &= ~G762_REG_FAN_CMD2_GEAR_MODE_1;
+		break;
+	case 2:
+		data->fan_cmd2 &= ~G762_REG_FAN_CMD2_GEAR_MODE_0;
+		data->fan_cmd2 |=  G762_REG_FAN_CMD2_GEAR_MODE_1;
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+	ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD2,
+					data->fan_cmd2);
+	data->valid = false;
+ out:
+	mutex_unlock(&data->update_lock);
+
+	return ret;
+}
+
+/* Set number of fan pulses per revolution. Accepts either 2 or 4. */
+static int do_set_fan_pulses(struct device *dev, unsigned long val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = g762_update_client(dev);
+	int ret;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	mutex_lock(&data->update_lock);
+	switch (val) {
+	case 2:
+		data->fan_cmd1 &= ~G762_REG_FAN_CMD1_PULSE_PER_REV;
+		break;
+	case 4:
+		data->fan_cmd1 |=  G762_REG_FAN_CMD1_PULSE_PER_REV;
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+	ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+					data->fan_cmd1);
+	data->valid = false;
+ out:
+	mutex_unlock(&data->update_lock);
+
+	return ret;
+}
+
+/* Set fan mode. Accepts either 1 (open-loop) or 2 (closed-loop). */
+static int do_set_pwm_enable(struct device *dev, unsigned long val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = g762_update_client(dev);
+	int ret;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	mutex_lock(&data->update_lock);
+	switch (val) {
+	case G762_FAN_MODE_CLOSED_LOOP:
+		data->fan_cmd1 |=  G762_REG_FAN_CMD1_FAN_MODE;
+		break;
+	case G762_FAN_MODE_OPEN_LOOP:
+		data->fan_cmd1 &= ~G762_REG_FAN_CMD1_FAN_MODE;
+		/*
+		 * BUG FIX: if SET_CNT register value is 255 then, for some
+		 * unknown reason, fan will not rotate as expected, no matter
+		 * the value of SET_OUT (to be specific, this seems to happen
+		 * only in PWM mode). To workaround this bug, we give SET_CNT
+		 * value of 254 if it is 255 when switching to open-loop.
+		 */
+		if (data->set_cnt == 0xff)
+			i2c_smbus_write_byte_data(client, G762_REG_SET_CNT,
+						  254);
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+
+	ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+					data->fan_cmd1);
+	data->valid = false;
+ out:
+	mutex_unlock(&data->update_lock);
+
+	return ret;
+}
+
+/* Set PWM polarity. Accepts either 0 (positive duty) or 1 (negative duty) */
+static int do_set_pwm_polarity(struct device *dev, unsigned long val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = g762_update_client(dev);
+	int ret;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	mutex_lock(&data->update_lock);
+	switch (val) {
+	case G762_PWM_POLARITY_POSITIVE:
+		data->fan_cmd1 &= ~G762_REG_FAN_CMD1_PWM_POLARITY;
+		break;
+	case G762_PWM_POLARITY_NEGATIVE:
+		data->fan_cmd1 |=  G762_REG_FAN_CMD1_PWM_POLARITY;
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+	ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+					data->fan_cmd1);
+	data->valid = false;
+ out:
+	mutex_unlock(&data->update_lock);
+
+	return ret;
+}
+
+/*
+ * Set pwm value. Accepts values between 0 (stops the fan) and
+ * 255 (full speed). This only makes sense in open-loop mode.
+ */
+static int do_set_pwm(struct device *dev, unsigned long val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = i2c_get_clientdata(client);
+	int ret;
+
+	if (val > 255)
+		return -EINVAL;
+
+	mutex_lock(&data->update_lock);
+	ret = i2c_smbus_write_byte_data(client, G762_REG_SET_OUT, val);
+	data->valid = false;
+	mutex_unlock(&data->update_lock);
+
+	return ret;
+}
+
+/*
+ * Set fan RPM value. Can be called both in closed and open-loop mode
+ * but effect will only be seen after closed-loop mode is configured.
+ */
+static int do_set_fan_target(struct device *dev, unsigned long val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = g762_update_client(dev);
+	int ret;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	mutex_lock(&data->update_lock);
+	data->set_cnt = cnt_from_rpm(val, data->clk_freq,
+				     G762_PULSE_FROM_REG(data->fan_cmd1),
+				     G762_CLKDIV_FROM_REG(data->fan_cmd1),
+				     G762_GEARMULT_FROM_REG(data->fan_cmd2));
+	ret = i2c_smbus_write_byte_data(client, G762_REG_SET_CNT,
+					data->set_cnt);
+	data->valid = false;
+	mutex_unlock(&data->update_lock);
+
+	return ret;
+}
+
+/* Set fan startup voltage. Accepted values are either 0, 1, 2 or 3. */
+static int do_set_fan_startv(struct device *dev, unsigned long val)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = g762_update_client(dev);
+	int ret;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	mutex_lock(&data->update_lock);
+	switch (val) {
+	case 0:
+		data->fan_cmd2 &= ~G762_REG_FAN_CMD2_FAN_STARTV_0;
+		data->fan_cmd2 &= ~G762_REG_FAN_CMD2_FAN_STARTV_1;
+		break;
+	case 1:
+		data->fan_cmd2 |=  G762_REG_FAN_CMD2_FAN_STARTV_0;
+		data->fan_cmd2 &= ~G762_REG_FAN_CMD2_FAN_STARTV_1;
+		break;
+	case 2:
+		data->fan_cmd2 &= ~G762_REG_FAN_CMD2_FAN_STARTV_0;
+		data->fan_cmd2 |=  G762_REG_FAN_CMD2_FAN_STARTV_1;
+		break;
+	case 3:
+		data->fan_cmd2 |=  G762_REG_FAN_CMD2_FAN_STARTV_0;
+		data->fan_cmd2 |=  G762_REG_FAN_CMD2_FAN_STARTV_1;
+		break;
+	default:
+		ret = -EINVAL;
+		goto out;
+	}
+	ret = i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD2,
+					data->fan_cmd2);
+	data->valid = false;
+ out:
+	mutex_unlock(&data->update_lock);
+
+	return ret;
+}
+
+/*
+ * Helper to import hardware characteristics from .dts file and push
+ * those to the chip.
+ */
+
+#ifdef CONFIG_OF
+static struct of_device_id g762_dt_match[] = {
+	{ .compatible = "gmt,g762" },
+	{ .compatible = "gmt,g763" },
+	{ },
+};
+
+/*
+ * Grab clock (a required property), enable it, get (fixed) clock frequency
+ * and store it. Note: upon success, clock has been prepared and enabled; it
+ * must later be unprepared and disabled (e.g. during module unloading) by a
+ * call to g762_of_clock_disable(). Note that a reference to clock is kept
+ * in our private data structure to be used in this function.
+ */
+static int g762_of_clock_enable(struct i2c_client *client)
+{
+	struct g762_data *data;
+	unsigned long clk_freq;
+	struct clk *clk;
+	int ret;
+
+	if (!client->dev.of_node)
+		return 0;
+
+	clk = of_clk_get(client->dev.of_node, 0);
+	if (IS_ERR(clk)) {
+		dev_err(&client->dev, "failed to get clock\n");
+		return PTR_ERR(clk);
+	}
+
+	ret = clk_prepare_enable(clk);
+	if (ret) {
+		dev_err(&client->dev, "failed to enable clock\n");
+		goto clk_put;
+	}
+
+	clk_freq = clk_get_rate(clk);
+	ret = do_set_clk_freq(&client->dev, clk_freq);
+	if (ret) {
+		dev_err(&client->dev, "invalid clock freq %lu\n", clk_freq);
+		goto clk_unprep;
+	}
+
+	data = i2c_get_clientdata(client);
+	data->clk = clk;
+
+	return 0;
+
+ clk_unprep:
+	clk_disable_unprepare(clk);
+
+ clk_put:
+	clk_put(clk);
+
+	return ret;
+}
+
+static void g762_of_clock_disable(struct i2c_client *client)
+{
+	struct g762_data *data = i2c_get_clientdata(client);
+
+	if (!data->clk)
+		return;
+
+	clk_disable_unprepare(data->clk);
+	clk_put(data->clk);
+}
+
+static int g762_of_prop_import_one(struct i2c_client *client,
+				   const char *pname,
+				   int (*psetter)(struct device *dev,
+						  unsigned long val))
+{
+	const __be32 *prop;
+	int len, ret;
+	u32 pval;
+
+	prop = of_get_property(client->dev.of_node, pname, &len);
+	if (!prop || len != sizeof(u32))
+		return 0;
+
+	pval = be32_to_cpu(prop[0]);
+	dev_dbg(&client->dev, "found %s (%d)\n", pname, pval);
+	ret = (*psetter)(&client->dev, pval);
+	if (ret)
+		dev_err(&client->dev, "unable to set %s (%d)\n", pname, pval);
+
+	return ret;
+}
+
+static int g762_of_prop_import(struct i2c_client *client)
+{
+	int ret;
+
+	if (!client->dev.of_node)
+		return 0;
+
+	ret = g762_of_prop_import_one(client, "fan_gear_mode",
+				      do_set_fan_gear_mode);
+	if (ret)
+		return ret;
+
+	ret = g762_of_prop_import_one(client, "pwm_polarity",
+				      do_set_pwm_polarity);
+	if (ret)
+		return ret;
+
+	return g762_of_prop_import_one(client, "fan_startv",
+				       do_set_fan_startv);
+}
+
+#else
+static int g762_of_prop_import(struct i2c_client *client)
+{
+	return 0;
+}
+
+static int g762_of_clock_enable(struct i2c_client *client)
+{
+	return 0;
+}
+
+static void g762_of_clock_disable(struct i2c_client *client) { }
+#endif
+
+/*
+ * Helper to import hardware characteristics from .dts file and push
+ * those to the chip.
+ */
+
+static int g762_pdata_prop_import(struct i2c_client *client)
+{
+	struct g762_platform_data *pdata = client->dev.platform_data;
+	int ret;
+
+	if (!pdata)
+		return 0;
+
+	ret = do_set_fan_gear_mode(&client->dev, pdata->fan_gear_mode);
+	if (ret)
+		return ret;
+
+	ret = do_set_pwm_polarity(&client->dev, pdata->pwm_polarity);
+	if (ret)
+		return ret;
+
+	ret = do_set_fan_startv(&client->dev, pdata->fan_startv);
+	if (ret)
+		return ret;
+
+	return do_set_clk_freq(&client->dev, pdata->clk_freq);
+}
+
+/*
+ * sysfs attributes
+ */
+
+/*
+ * Read function for fan1_input sysfs file. Return current fan RPM value, or
+ * 0 if fan is out of control.
+ */
+static ssize_t get_fan_rpm(struct device *dev, struct device_attribute *da,
+			   char *buf)
+{
+	struct g762_data *data = g762_update_client(dev);
+	unsigned int rpm = 0;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	mutex_lock(&data->update_lock);
+	/* reverse logic: fan out of control reporting is enabled low */
+	if (data->fan_sta & G762_REG_FAN_STA_OOC) {
+		rpm = rpm_from_cnt(data->act_cnt, data->clk_freq,
+				   G762_PULSE_FROM_REG(data->fan_cmd1),
+				   G762_CLKDIV_FROM_REG(data->fan_cmd1),
+				   G762_GEARMULT_FROM_REG(data->fan_cmd2));
+	}
+	mutex_unlock(&data->update_lock);
+
+	return sprintf(buf, "%u\n", rpm);
+}
+
+/*
+ * Read and write functions for pwm1_mode sysfs file. Get and set fan speed
+ * control mode i.e. PWM (1) or DC (0).
+ */
+static ssize_t get_pwm_mode(struct device *dev, struct device_attribute *da,
+			    char *buf)
+{
+	struct g762_data *data = g762_update_client(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return sprintf(buf, "%d\n",
+		       !!(data->fan_cmd1 & G762_REG_FAN_CMD1_OUT_MODE));
+}
+
+static ssize_t set_pwm_mode(struct device *dev, struct device_attribute *da,
+			    const char *buf, size_t count)
+{
+	unsigned long val;
+	int ret;
+
+	if (kstrtoul(buf, 10, &val))
+		return -EINVAL;
+
+	ret = do_set_pwm_mode(dev, val);
+	if (ret < 0)
+		return ret;
+
+	return count;
+}
+
+/*
+ * Read and write functions for fan1_div sysfs file. Get and set fan
+ * controller prescaler value
+ */
+static ssize_t get_fan_div(struct device *dev,
+			   struct device_attribute *da, char *buf)
+{
+	struct g762_data *data = g762_update_client(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return sprintf(buf, "%d\n", G762_CLKDIV_FROM_REG(data->fan_cmd1));
+}
+
+static ssize_t set_fan_div(struct device *dev,
+			   struct device_attribute *da,
+			   const char *buf, size_t count)
+{
+	unsigned long val;
+	int ret;
+
+	if (kstrtoul(buf, 10, &val))
+		return -EINVAL;
+
+	ret = do_set_fan_div(dev, val);
+	if (ret < 0)
+		return ret;
+
+	return count;
+}
+
+/*
+ * Read and write functions for fan1_pulses sysfs file. Get and set number
+ * of tachometer pulses per fan revolution.
+ */
+static ssize_t get_fan_pulses(struct device *dev,
+			      struct device_attribute *da, char *buf)
+{
+	struct g762_data *data = g762_update_client(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return sprintf(buf, "%d\n", G762_PULSE_FROM_REG(data->fan_cmd1));
+}
+
+static ssize_t set_fan_pulses(struct device *dev,
+			      struct device_attribute *da,
+			      const char *buf, size_t count)
+{
+	unsigned long val;
+	int ret;
+
+	if (kstrtoul(buf, 10, &val))
+		return -EINVAL;
+
+	ret = do_set_fan_pulses(dev, val);
+	if (ret < 0)
+		return ret;
+
+	return count;
+}
+
+/*
+ * Read and write functions for pwm1_enable. Get and set fan speed control mode
+ * (i.e. closed or open-loop).
+ *
+ * Following documentation about hwmon's sysfs interface, a pwm1_enable node
+ * should accept followings:
+ *
+ *  0 : no fan speed control (i.e. fan at full speed)
+ *  1 : manual fan speed control enabled (use pwm[1-*]) (open-loop)
+ *  2+: automatic fan speed control enabled (use fan[1-*]_target) (closed-loop)
+ *
+ * but we do not accept 0 as this mode is not natively supported by the chip
+ * and it is not emulated by g762 driver. -EINVAL is returned in this case.
+ */
+static ssize_t get_pwm_enable(struct device *dev,
+			      struct device_attribute *da, char *buf)
+{
+	struct g762_data *data = g762_update_client(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return sprintf(buf, "%d\n",
+		       (!!(data->fan_cmd1 & G762_REG_FAN_CMD1_FAN_MODE)) + 1);
+}
+
+static ssize_t set_pwm_enable(struct device *dev,
+			      struct device_attribute *da,
+			      const char *buf, size_t count)
+{
+	unsigned long val;
+	int ret;
+
+	if (kstrtoul(buf, 10, &val))
+		return -EINVAL;
+
+	ret = do_set_pwm_enable(dev, val);
+	if (ret < 0)
+		return ret;
+
+	return count;
+}
+
+/*
+ * Read and write functions for pwm1 sysfs file. Get and set pwm value
+ * (which affects fan speed) in open-loop mode. 0 stops the fan and 255
+ * makes it run at full speed.
+ */
+static ssize_t get_pwm(struct device *dev, struct device_attribute *da,
+		       char *buf)
+{
+	struct g762_data *data = g762_update_client(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return sprintf(buf, "%d\n", data->set_out);
+}
+
+static ssize_t set_pwm(struct device *dev, struct device_attribute *da,
+		       const char *buf, size_t count)
+{
+	unsigned long val;
+	int ret;
+
+	if (kstrtoul(buf, 10, &val))
+		return -EINVAL;
+
+	ret = do_set_pwm(dev, val);
+	if (ret < 0)
+		return ret;
+
+	return count;
+}
+
+/*
+ * Read and write function for fan1_target sysfs file. Get/set the fan speed in
+ * closed-loop mode. Speed is given as a RPM value; then the chip will regulate
+ * the fan speed using pulses from fan tachometer.
+ *
+ * Refer to rpm_from_cnt() implementation above to get info about count number
+ * calculation.
+ *
+ * Also note that due to rounding errors it is possible that you don't read
+ * back exactly the value you have set.
+ */
+static ssize_t get_fan_target(struct device *dev, struct device_attribute *da,
+			      char *buf)
+{
+	struct g762_data *data = g762_update_client(dev);
+	unsigned int rpm;
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	mutex_lock(&data->update_lock);
+	rpm = rpm_from_cnt(data->set_cnt, data->clk_freq,
+			   G762_PULSE_FROM_REG(data->fan_cmd1),
+			   G762_CLKDIV_FROM_REG(data->fan_cmd1),
+			   G762_GEARMULT_FROM_REG(data->fan_cmd2));
+	mutex_unlock(&data->update_lock);
+
+	return sprintf(buf, "%u\n", rpm);
+}
+
+static ssize_t set_fan_target(struct device *dev, struct device_attribute *da,
+			      const char *buf, size_t count)
+{
+	unsigned long val;
+	int ret;
+
+	if (kstrtoul(buf, 10, &val))
+		return -EINVAL;
+
+	ret = do_set_fan_target(dev, val);
+	if (ret < 0)
+		return ret;
+
+	return count;
+}
+
+/* read function for fan1_fault sysfs file. */
+static ssize_t get_fan_failure(struct device *dev, struct device_attribute *da,
+			       char *buf)
+{
+	struct g762_data *data = g762_update_client(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return sprintf(buf, "%u\n", !!(data->fan_sta & G762_REG_FAN_STA_FAIL));
+}
+
+/*
+ * read function for fan1_alarm sysfs file. Note that OOC condition is
+ * enabled low
+ */
+static ssize_t get_fan_ooc(struct device *dev, struct device_attribute *da,
+			   char *buf)
+{
+	struct g762_data *data = g762_update_client(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	return sprintf(buf, "%u\n", !(data->fan_sta & G762_REG_FAN_STA_OOC));
+}
+
+static DEVICE_ATTR(pwm1, S_IWUSR | S_IRUGO, get_pwm, set_pwm);
+static DEVICE_ATTR(pwm1_mode, S_IWUSR | S_IRUGO, get_pwm_mode, set_pwm_mode);
+static DEVICE_ATTR(pwm1_enable, S_IWUSR | S_IRUGO,
+		   get_pwm_enable, set_pwm_enable);
+static DEVICE_ATTR(fan1_input, S_IRUGO, get_fan_rpm, NULL);
+static DEVICE_ATTR(fan1_alarm, S_IRUGO, get_fan_ooc, NULL);
+static DEVICE_ATTR(fan1_fault, S_IRUGO, get_fan_failure, NULL);
+static DEVICE_ATTR(fan1_target, S_IWUSR | S_IRUGO,
+		   get_fan_target, set_fan_target);
+static DEVICE_ATTR(fan1_div, S_IWUSR | S_IRUGO, get_fan_div, set_fan_div);
+static DEVICE_ATTR(fan1_pulses, S_IWUSR | S_IRUGO,
+		   get_fan_pulses, set_fan_pulses);
+
+/* Driver data */
+static struct attribute *g762_attributes[] = {
+	&dev_attr_fan1_input.attr,
+	&dev_attr_fan1_alarm.attr,
+	&dev_attr_fan1_fault.attr,
+	&dev_attr_fan1_target.attr,
+	&dev_attr_fan1_div.attr,
+	&dev_attr_fan1_pulses.attr,
+	&dev_attr_pwm1.attr,
+	&dev_attr_pwm1_mode.attr,
+	&dev_attr_pwm1_enable.attr,
+	NULL
+};
+
+static const struct attribute_group g762_group = {
+	.attrs = g762_attributes,
+};
+
+/*
+ * Enable both fan failure detection and fan out of control protection. The
+ * function does not protect change/access to data structure; it must thus
+ * only be called during initialization.
+ */
+static inline int g762_fan_init(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct g762_data *data = g762_update_client(dev);
+
+	if (IS_ERR(data))
+		return PTR_ERR(data);
+
+	data->fan_cmd1 |= G762_REG_FAN_CMD1_DET_FAN_FAIL;
+	data->fan_cmd1 |= G762_REG_FAN_CMD1_DET_FAN_OOC;
+	data->valid = false;
+
+	return i2c_smbus_write_byte_data(client, G762_REG_FAN_CMD1,
+					 data->fan_cmd1);
+}
+
+static int g762_probe(struct i2c_client *client, const struct i2c_device_id *id)
+{
+	struct g762_data *data;
+	int ret;
+
+	if (!i2c_check_functionality(client->adapter,
+				     I2C_FUNC_SMBUS_BYTE_DATA))
+		return -ENODEV;
+
+	data = devm_kzalloc(&client->dev, sizeof(struct g762_data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	i2c_set_clientdata(client, data);
+	data->client = client;
+	mutex_init(&data->update_lock);
+
+	/* Enable fan failure detection and fan out of control protection */
+	ret = g762_fan_init(&client->dev);
+	if (ret)
+		return ret;
+
+	/* Get configuration via DT ... */
+	ret = g762_of_clock_enable(client);
+	if (ret)
+		return ret;
+	ret = g762_of_prop_import(client);
+	if (ret)
+		goto clock_dis;
+	/* ... or platform_data */
+	ret = g762_pdata_prop_import(client);
+	if (ret)
+		goto clock_dis;
+
+	/* Register sysfs hooks */
+	ret = sysfs_create_group(&client->dev.kobj, &g762_group);
+	if (ret)
+		goto clock_dis;
+
+	data->hwmon_dev = hwmon_device_register(&client->dev);
+	if (IS_ERR(data->hwmon_dev)) {
+		ret = PTR_ERR(data->hwmon_dev);
+		goto sysfs_rem;
+	}
+
+	return 0;
+
+ sysfs_rem:
+	sysfs_remove_group(&client->dev.kobj, &g762_group);
+
+ clock_dis:
+	g762_of_clock_disable(client);
+
+	return ret;
+}
+
+static int g762_remove(struct i2c_client *client)
+{
+	struct g762_data *data = i2c_get_clientdata(client);
+
+	hwmon_device_unregister(data->hwmon_dev);
+	sysfs_remove_group(&client->dev.kobj, &g762_group);
+	g762_of_clock_disable(client);
+
+	return 0;
+}
+
+static struct i2c_driver g762_driver = {
+	.driver = {
+		.name = DRVNAME,
+		.owner = THIS_MODULE,
+		.of_match_table = of_match_ptr(g762_dt_match),
+	},
+	.probe	  = g762_probe,
+	.remove	  = g762_remove,
+	.id_table = g762_id,
+};
+
+module_i2c_driver(g762_driver);
+
+MODULE_AUTHOR("Arnaud EBALARD <arno@natisbad.org>");
+MODULE_DESCRIPTION("GMT G762/G763 driver");
+MODULE_LICENSE("GPL");