Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 81 insertions, 0 deletions

diff --git a/drivers/fc4/Kconfig b/drivers/fc4/Kconfig
new file mode 100644
index 00000000000..f00c02a13ed
--- /dev/null
+++ b/drivers/fc4/Kconfig
@@ -0,0 +1,81 @@
+#
+# FC4 device configuration
+#
+
+menu "Fibre Channel support"
+
+config FC4
+	tristate "Fibre Channel and FC4 SCSI support"
+	---help---
+	  Fibre Channel is a high speed serial protocol mainly used to
+	  connect large storage devices to the computer; it is compatible with
+	  and intended to replace SCSI.
+
+	  This is an experimental support for storage arrays connected to your
+	  computer using optical fibre cables and the "X3.269-199X Fibre
+	  Channel Protocol for SCSI" specification. If you want to use this,
+	  you need to say Y here and to "SCSI support" as well as to the
+	  drivers for the storage array itself and for the interface adapter
+	  such as SOC or SOC+. This subsystem could even serve for IP
+	  networking, with some code extensions.
+
+	  If unsure, say N.
+
+comment "FC4 drivers"
+	depends on FC4
+
+config FC4_SOC
+	tristate "Sun SOC/Sbus"
+	depends on FC4!=n && (SPARC32 || SPARC64)
+	help
+	  Serial Optical Channel is an interface card with one or two Fibre
+	  Optic ports, each of which can be connected to a disk array. Note
+	  that if you have older firmware in the card, you'll need the
+	  microcode from the Solaris driver to make it work.
+
+	  To compile this support as a module, choose M here: the module will
+	  be called soc.
+
+config FC4_SOCAL
+	tristate "Sun SOC+ (aka SOCAL)"
+	depends on FC4!=n && (SPARC32 || SPARC64)
+	---help---
+	  Serial Optical Channel Plus is an interface card with up to two
+	  Fibre Optic ports. This card supports FC Arbitrated Loop (usually
+	  A5000 or internal FC disks in E[3-6]000 machines through the
+	  Interface Board). You'll probably need the microcode from the
+	  Solaris driver to make it work.
+
+	  To compile this support as a module, choose M here: the module will
+	  be called socal.
+
+comment "FC4 targets"
+	depends on FC4
+
+config SCSI_PLUTO
+	tristate "SparcSTORAGE Array 100 and 200 series"
+	depends on FC4!=n && SCSI
+	help
+	  If you never bought a disk array made by Sun, go with N.
+
+	  To compile this support as a module, choose M here: the module will
+	  be called pluto.
+
+config SCSI_FCAL
+	tristate "Sun Enterprise Network Array (A5000 and EX500)" if SPARC32 || SPARC64
+	depends on FC4!=n && SCSI
+	help
+	  This driver drives FC-AL disks connected through a Fibre Channel
+	  card using the drivers/fc4 layer (currently only SOCAL). The most
+	  common is either A5000 array or internal disks in E[3-6]000
+	  machines.
+
+	  To compile this support as a module, choose M here: the module will
+	  be called fcal.
+
+config SCSI_FCAL
+	prompt "Generic FC-AL disk driver"
+	depends on FC4!=n && SCSI && !SPARC32 && !SPARC64
+
+endmenu
+