Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC multiplatform conversion patches from Olof Johansson:
 "Here are more patches in the progression towards multiplatform, sparse
  irq conversions in particular.

  Tegra has a handful of cleanups and general groundwork, but is not
  quite there yet on full enablement.

  Platforms that are enabled through this branch are VT8500 and Zynq.
  Note that i.MX was converted in one of the earlier cleanup branches as
  well (before we started a separate topic for multiplatform).  And both
  new platforms for this merge window, sunxi and bcm, were merged with
  multiplatform support enabled."

Fix up conflicts mostly as per Olof.

* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
  ARM: zynq: Remove all unused mach headers
  ARM: zynq: add support for ARCH_MULTIPLATFORM
  ARM: zynq: make use of debug_ll_io_init()
  ARM: zynq: remove TTC early mapping
  ARM: tegra: move debug-macro.S to include/debug
  ARM: tegra: don't include iomap.h from debug-macro.S
  ARM: tegra: decouple uncompress.h and debug-macro.S
  ARM: tegra: simplify DEBUG_LL UART selection options
  ARM: tegra: select SPARSE_IRQ
  ARM: tegra: enhance timer.c to get IO address from device tree
  ARM: tegra: enhance timer.c to get IRQ info from device tree
  ARM: timer: fix checkpatch warnings
  ARM: tegra: add TWD to device tree
  ARM: tegra: define DT bindings for and instantiate RTC
  ARM: tegra: define DT bindings for and instantiate timer
  clocksource/mtu-nomadik: use apb_pclk
  clk: ux500: Register mtu apb_pclocks
  ARM: plat-nomadik: convert platforms to SPARSE_IRQ
  mfd/db8500-prcmu: use the irq_domain_add_simple()
  mfd/ab8500-core: use irq_domain_add_simple()
  ...

3 files changed, 247 insertions, 1 deletions

diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index a0985732f1e..7fdcbd3f4da 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -25,6 +25,21 @@ config ARMADA_370_XP_TIMER
 config SUNXI_TIMER
 	bool
 
+config CLKSRC_NOMADIK_MTU
+	bool
+	depends on (ARCH_NOMADIK || ARCH_U8500)
+	select CLKSRC_MMIO
+	help
+	  Support for Multi Timer Unit. MTU provides access
+	  to multiple interrupt generating programmable
+	  32-bit free running decrementing counters.
+
+config CLKSRC_NOMADIK_MTU_SCHED_CLOCK
+	bool
+	depends on CLKSRC_NOMADIK_MTU
+	help
+	  Use the Multi Timer Unit as the sched_clock.
+
 config CLKSRC_DBX500_PRCMU
 	bool "Clocksource PRCMU Timer"
 	depends on UX500_SOC_DB8500
@@ -34,7 +49,7 @@ config CLKSRC_DBX500_PRCMU
 
 config CLKSRC_DBX500_PRCMU_SCHED_CLOCK
 	bool "Clocksource PRCMU Timer sched_clock"
-	depends on (CLKSRC_DBX500_PRCMU && !NOMADIK_MTU_SCHED_CLOCK)
+	depends on (CLKSRC_DBX500_PRCMU && !CLKSRC_NOMADIK_MTU_SCHED_CLOCK)
 	default y
 	help
 	  Use the always on PRCMU Timer as sched_clock
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 36f06de4c5a..f93453d0167 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_CLKBLD_I8253)	+= i8253.o
 obj-$(CONFIG_CLKSRC_MMIO)	+= mmio.o
 obj-$(CONFIG_DW_APB_TIMER)	+= dw_apb_timer.o
 obj-$(CONFIG_DW_APB_TIMER_OF)	+= dw_apb_timer_of.o
+obj-$(CONFIG_CLKSRC_NOMADIK_MTU)	+= nomadik-mtu.o
 obj-$(CONFIG_CLKSRC_DBX500_PRCMU)	+= clksrc-dbx500-prcmu.o
 obj-$(CONFIG_ARMADA_370_XP_TIMER)	+= time-armada-370-xp.o
 obj-$(CONFIG_ARCH_BCM2835)	+= bcm2835_timer.o
diff --git a/drivers/clocksource/nomadik-mtu.c b/drivers/clocksource/nomadik-mtu.c
new file mode 100644
index 00000000000..8914c3c1c88
--- /dev/null
+++ b/drivers/clocksource/nomadik-mtu.c
@@ -0,0 +1,230 @@
+/*
+ * Copyright (C) 2008 STMicroelectronics
+ * Copyright (C) 2010 Alessandro Rubini
+ * Copyright (C) 2010 Linus Walleij for ST-Ericsson
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2, as
+ * published by the Free Software Foundation.
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+#include <linux/clk.h>
+#include <linux/jiffies.h>
+#include <linux/err.h>
+#include <linux/platform_data/clocksource-nomadik-mtu.h>
+#include <asm/mach/time.h>
+#include <asm/sched_clock.h>
+
+/*
+ * The MTU device hosts four different counters, with 4 set of
+ * registers. These are register names.
+ */
+
+#define MTU_IMSC	0x00	/* Interrupt mask set/clear */
+#define MTU_RIS		0x04	/* Raw interrupt status */
+#define MTU_MIS		0x08	/* Masked interrupt status */
+#define MTU_ICR		0x0C	/* Interrupt clear register */
+
+/* per-timer registers take 0..3 as argument */
+#define MTU_LR(x)	(0x10 + 0x10 * (x) + 0x00)	/* Load value */
+#define MTU_VAL(x)	(0x10 + 0x10 * (x) + 0x04)	/* Current value */
+#define MTU_CR(x)	(0x10 + 0x10 * (x) + 0x08)	/* Control reg */
+#define MTU_BGLR(x)	(0x10 + 0x10 * (x) + 0x0c)	/* At next overflow */
+
+/* bits for the control register */
+#define MTU_CRn_ENA		0x80
+#define MTU_CRn_PERIODIC	0x40	/* if 0 = free-running */
+#define MTU_CRn_PRESCALE_MASK	0x0c
+#define MTU_CRn_PRESCALE_1		0x00
+#define MTU_CRn_PRESCALE_16		0x04
+#define MTU_CRn_PRESCALE_256		0x08
+#define MTU_CRn_32BITS		0x02
+#define MTU_CRn_ONESHOT		0x01	/* if 0 = wraps reloading from BGLR*/
+
+/* Other registers are usual amba/primecell registers, currently not used */
+#define MTU_ITCR	0xff0
+#define MTU_ITOP	0xff4
+
+#define MTU_PERIPH_ID0	0xfe0
+#define MTU_PERIPH_ID1	0xfe4
+#define MTU_PERIPH_ID2	0xfe8
+#define MTU_PERIPH_ID3	0xfeC
+
+#define MTU_PCELL0	0xff0
+#define MTU_PCELL1	0xff4
+#define MTU_PCELL2	0xff8
+#define MTU_PCELL3	0xffC
+
+static void __iomem *mtu_base;
+static bool clkevt_periodic;
+static u32 clk_prescale;
+static u32 nmdk_cycle;		/* write-once */
+
+#ifdef CONFIG_NOMADIK_MTU_SCHED_CLOCK
+/*
+ * Override the global weak sched_clock symbol with this
+ * local implementation which uses the clocksource to get some
+ * better resolution when scheduling the kernel.
+ */
+static u32 notrace nomadik_read_sched_clock(void)
+{
+	if (unlikely(!mtu_base))
+		return 0;
+
+	return -readl(mtu_base + MTU_VAL(0));
+}
+#endif
+
+/* Clockevent device: use one-shot mode */
+static int nmdk_clkevt_next(unsigned long evt, struct clock_event_device *ev)
+{
+	writel(1 << 1, mtu_base + MTU_IMSC);
+	writel(evt, mtu_base + MTU_LR(1));
+	/* Load highest value, enable device, enable interrupts */
+	writel(MTU_CRn_ONESHOT | clk_prescale |
+	       MTU_CRn_32BITS | MTU_CRn_ENA,
+	       mtu_base + MTU_CR(1));
+
+	return 0;
+}
+
+void nmdk_clkevt_reset(void)
+{
+	if (clkevt_periodic) {
+		/* Timer: configure load and background-load, and fire it up */
+		writel(nmdk_cycle, mtu_base + MTU_LR(1));
+		writel(nmdk_cycle, mtu_base + MTU_BGLR(1));
+
+		writel(MTU_CRn_PERIODIC | clk_prescale |
+		       MTU_CRn_32BITS | MTU_CRn_ENA,
+		       mtu_base + MTU_CR(1));
+		writel(1 << 1, mtu_base + MTU_IMSC);
+	} else {
+		/* Generate an interrupt to start the clockevent again */
+		(void) nmdk_clkevt_next(nmdk_cycle, NULL);
+	}
+}
+
+static void nmdk_clkevt_mode(enum clock_event_mode mode,
+			     struct clock_event_device *dev)
+{
+	switch (mode) {
+	case CLOCK_EVT_MODE_PERIODIC:
+		clkevt_periodic = true;
+		nmdk_clkevt_reset();
+		break;
+	case CLOCK_EVT_MODE_ONESHOT:
+		clkevt_periodic = false;
+		break;
+	case CLOCK_EVT_MODE_SHUTDOWN:
+	case CLOCK_EVT_MODE_UNUSED:
+		writel(0, mtu_base + MTU_IMSC);
+		/* disable timer */
+		writel(0, mtu_base + MTU_CR(1));
+		/* load some high default value */
+		writel(0xffffffff, mtu_base + MTU_LR(1));
+		break;
+	case CLOCK_EVT_MODE_RESUME:
+		break;
+	}
+}
+
+static struct clock_event_device nmdk_clkevt = {
+	.name		= "mtu_1",
+	.features	= CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_PERIODIC,
+	.rating		= 200,
+	.set_mode	= nmdk_clkevt_mode,
+	.set_next_event	= nmdk_clkevt_next,
+};
+
+/*
+ * IRQ Handler for timer 1 of the MTU block.
+ */
+static irqreturn_t nmdk_timer_interrupt(int irq, void *dev_id)
+{
+	struct clock_event_device *evdev = dev_id;
+
+	writel(1 << 1, mtu_base + MTU_ICR); /* Interrupt clear reg */
+	evdev->event_handler(evdev);
+	return IRQ_HANDLED;
+}
+
+static struct irqaction nmdk_timer_irq = {
+	.name		= "Nomadik Timer Tick",
+	.flags		= IRQF_DISABLED | IRQF_TIMER,
+	.handler	= nmdk_timer_interrupt,
+	.dev_id		= &nmdk_clkevt,
+};
+
+void nmdk_clksrc_reset(void)
+{
+	/* Disable */
+	writel(0, mtu_base + MTU_CR(0));
+
+	/* ClockSource: configure load and background-load, and fire it up */
+	writel(nmdk_cycle, mtu_base + MTU_LR(0));
+	writel(nmdk_cycle, mtu_base + MTU_BGLR(0));
+
+	writel(clk_prescale | MTU_CRn_32BITS | MTU_CRn_ENA,
+	       mtu_base + MTU_CR(0));
+}
+
+void __init nmdk_timer_init(void __iomem *base, int irq)
+{
+	unsigned long rate;
+	struct clk *clk0, *pclk0;
+
+	mtu_base = base;
+
+	pclk0 = clk_get_sys("mtu0", "apb_pclk");
+	BUG_ON(IS_ERR(pclk0));
+	BUG_ON(clk_prepare(pclk0) < 0);
+	BUG_ON(clk_enable(pclk0) < 0);
+
+	clk0 = clk_get_sys("mtu0", NULL);
+	BUG_ON(IS_ERR(clk0));
+	BUG_ON(clk_prepare(clk0) < 0);
+	BUG_ON(clk_enable(clk0) < 0);
+
+	/*
+	 * Tick rate is 2.4MHz for Nomadik and 2.4Mhz, 100MHz or 133 MHz
+	 * for ux500.
+	 * Use a divide-by-16 counter if the tick rate is more than 32MHz.
+	 * At 32 MHz, the timer (with 32 bit counter) can be programmed
+	 * to wake-up at a max 127s a head in time. Dividing a 2.4 MHz timer
+	 * with 16 gives too low timer resolution.
+	 */
+	rate = clk_get_rate(clk0);
+	if (rate > 32000000) {
+		rate /= 16;
+		clk_prescale = MTU_CRn_PRESCALE_16;
+	} else {
+		clk_prescale = MTU_CRn_PRESCALE_1;
+	}
+
+	/* Cycles for periodic mode */
+	nmdk_cycle = DIV_ROUND_CLOSEST(rate, HZ);
+
+
+	/* Timer 0 is the free running clocksource */
+	nmdk_clksrc_reset();
+
+	if (clocksource_mmio_init(mtu_base + MTU_VAL(0), "mtu_0",
+			rate, 200, 32, clocksource_mmio_readl_down))
+		pr_err("timer: failed to initialize clock source %s\n",
+		       "mtu_0");
+
+#ifdef CONFIG_NOMADIK_MTU_SCHED_CLOCK
+	setup_sched_clock(nomadik_read_sched_clock, 32, rate);
+#endif
+
+	/* Timer 1 is used for events, register irq and clockevents */
+	setup_irq(irq, &nmdk_timer_irq);
+	nmdk_clkevt.cpumask = cpumask_of(0);
+	clockevents_config_and_register(&nmdk_clkevt, rate, 2, 0xffffffffU);
+}