Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 107 insertions, 0 deletions

diff --git a/drivers/char/ip2/ip2.h b/drivers/char/ip2/ip2.h
new file mode 100644
index 00000000000..936ccc53394
--- /dev/null
+++ b/drivers/char/ip2/ip2.h
@@ -0,0 +1,107 @@
+/*******************************************************************************
+*
+*   (c) 1998 by Computone Corporation
+*
+********************************************************************************
+*
+*
+*   PACKAGE:     Linux tty Device Driver for IntelliPort II family of multiport
+*                serial I/O controllers.
+*
+*   DESCRIPTION: Driver constants for configuration and tuning
+*
+*   NOTES:
+*
+*******************************************************************************/
+#ifndef IP2_H
+#define IP2_H
+
+#include "ip2types.h"
+#include "i2cmd.h"
+
+/*************/
+/* Constants */
+/*************/
+
+/* Device major numbers - since version 2.0.26. */
+#define IP2_TTY_MAJOR      71
+#define IP2_CALLOUT_MAJOR  72
+#define IP2_IPL_MAJOR      73
+
+/* Board configuration array.
+ * This array defines the hardware irq and address for up to IP2_MAX_BOARDS
+ * (4 supported per ip2_types.h) ISA board addresses and irqs MUST be specified,
+ * PCI and EISA boards are probed for and automagicly configed
+ * iff the addresses are set to 1 and 2 respectivily.
+ *    0x0100 - 0x03f0 == ISA
+ *	         1        == PCI
+ *	         2        == EISA
+ *	         0        == (skip this board)
+ * This array defines the hardware addresses for them. Special 
+ * addresses are EISA and PCI which go sniffing for boards. 
+
+ * In a multiboard system the position in the array determines which port
+ * devices are assigned to each board: 
+ *		board 0 is assigned ttyF0.. to ttyF63, 
+ *		board 1 is assigned ttyF64  to ttyF127,
+ *		board 2 is assigned ttyF128 to ttyF191,
+ *		board 3 is assigned ttyF192 to ttyF255. 
+ *
+ * In PCI and EISA bus systems each range is mapped to card in 
+ * monotonically increasing slot number order, ISA position is as specified
+ * here.
+
+ * If the irqs are ALL set to 0,0,0,0 all boards operate in 
+ * polled mode. For interrupt operation ISA boards require that the IRQ be 
+ * specified, while PCI and EISA boards any nonzero entry 
+ * will enable interrupts using the BIOS configured irq for the board. 
+ * An invalid irq entry will default to polled mode for that card and print
+ * console warning.
+ 
+ * When the driver is loaded as a module these setting can be overridden on the 
+ * modprobe command line or on an option line in /etc/modprobe.conf.
+ * If the driver is built-in the configuration must be 
+ * set here for ISA cards and address set to 1 and 2 for PCI and EISA.
+ *
+ * Here is an example that shows most if not all possibe combinations:
+
+ *static ip2config_t ip2config =
+ *{
+ *	{11,1,0,0},		// irqs
+ *	{				// Addresses
+ *		0x0308,		// Board 0, ttyF0   - ttyF63// ISA card at io=0x308, irq=11
+ *		0x0001,		// Board 1, ttyF64  - ttyF127//PCI card configured by BIOS
+ *		0x0000,		// Board 2, ttyF128 - ttyF191// Slot skipped
+ *		0x0002		// Board 3, ttyF192 - ttyF255//EISA card configured by BIOS
+ *												 // but polled not irq driven
+ *	}
+ *};
+ */
+
+ /* this structure is zeroed out because the suggested method is to configure
+  * the driver as a module, set up the parameters with an options line in
+  * /etc/modprobe.conf and load with modprobe or kmod, the kernel
+  * module loader
+  */
+
+ /* This structure is NOW always initialized when the driver is initialized.
+  * Compiled in defaults MUST be added to the io and irq arrays in
+  * ip2.c.  Those values are configurable from insmod parameters in the
+  * case of modules or from command line parameters (ip2=io,irq) when
+  * compiled in.
+  */
+
+static ip2config_t ip2config =
+{
+	{0,0,0,0},		// irqs
+	{				// Addresses
+	/* Do NOT set compile time defaults HERE!  Use the arrays in
+		ip2.c!  These WILL be overwritten!  =mhw= */
+		0x0000,		// Board 0, ttyF0   - ttyF63
+		0x0000,		// Board 1, ttyF64  - ttyF127
+		0x0000,		// Board 2, ttyF128 - ttyF191
+		0x0000		// Board 3, ttyF192 - ttyF255
+	}
+};
+
+#endif