Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (82 commits)
  [PATCH] pata_ali: small fixes
  [PATCH] pata_via: VIA 8251 bridged systems are now out and about
  [PATCH] trivial piix: swap bogus dot for comma space
  [PATCH] sata_promise: PHYMODE4 fixup
  [PATCH] libata: always use polling IDENTIFY
  [libata] pata_cs5535: fix build
  [PATCH] ahci: do not powerdown during initialization
  [PATCH] libata: prepare ata_sg_clean() for invocation from EH
  [PATCH] libata: separate out rw ATA taskfile building into ata_build_rw_tf()
  [PATCH] libata: implement ata_exec_internal_sg()
  [PATCH] libata: make sure IRQ is cleared after ata_bmdma_freeze()
  [PATCH] libata: move BMDMA host status recording from EH to interrupt handler
  [PATCH] libata: make sure sdev doesn't go away while rescanning
  [PATCH] libata: don't request sense if the port is frozen
  [PATCH] libata: fix READ CAPACITY simulation
  [PATCH] libata: implement ATA_FLAG_SETXFER_POLLING and use it in pata_via, take #2
  [PATCH] libata: set IRQF_SHARED for legacy PCI IDE IRQs
  [PATCH] libata: remove unused HSM_ST_UNKNOWN
  [PATCH] libata: kill unnecessary sht->max_sectors initializations
  [PATCH] libata: add missing sht->slave_destroy
  ...

1 files changed, 6 insertions, 28 deletions

diff --git a/drivers/ata/pata_opti.c b/drivers/ata/pata_opti.c
index c6319cf50de..c2988b0aa8e 100644
--- a/drivers/ata/pata_opti.c
+++ b/drivers/ata/pata_opti.c
@@ -34,7 +34,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME "pata_opti"
-#define DRV_VERSION "0.2.5"
+#define DRV_VERSION "0.2.7"
 
 enum {
 	READ_REG	= 0,	/* index of Read cycle timing register */
@@ -109,30 +109,6 @@ static void opti_write_reg(struct ata_port *ap, u8 val, int reg)
 	outb(0x83, regio + 2);
 }
 
-#if 0
-/**
- *	opti_read_reg		-	control register read
- *	@ap: ATA port
- *	@reg: control register number
- *
- *	The Opti uses magic 'trapdoor' register accesses to do configuration
- *	rather than using PCI space as other controllers do. The double inw
- *	on the error register activates configuration mode. We can then read
- *	the control register
- */
-
-static u8 opti_read_reg(struct ata_port *ap, int reg)
-{
-	unsigned long regio = ap->ioaddr.cmd_addr;
-	u8 ret;
-	inw(regio + 1);
-	inw(regio + 1);
-	outb(3, regio + 2);
-	ret = inb(regio + reg);
-	outb(0x83, regio + 2);
-}
-#endif
-
 /**
  *	opti_set_piomode	-	set initial PIO mode data
  *	@ap: ATA interface
@@ -195,7 +171,6 @@ static struct scsi_host_template opti_sht = {
 	.can_queue		= ATA_DEF_QUEUE,
 	.this_id		= ATA_SHT_THIS_ID,
 	.sg_tablesize		= LIBATA_MAX_PRD,
-	.max_sectors		= ATA_MAX_SECTORS,
 	.cmd_per_lun		= ATA_SHT_CMD_PER_LUN,
 	.emulated		= ATA_SHT_EMULATED,
 	.use_clustering		= ATA_SHT_USE_CLUSTERING,
@@ -204,12 +179,13 @@ static struct scsi_host_template opti_sht = {
 	.slave_configure	= ata_scsi_slave_config,
 	.slave_destroy		= ata_scsi_slave_destroy,
 	.bios_param		= ata_std_bios_param,
+	.resume			= ata_scsi_device_resume,
+	.suspend		= ata_scsi_device_suspend,
 };
 
 static struct ata_port_operations opti_port_ops = {
 	.port_disable	= ata_port_disable,
 	.set_piomode	= opti_set_piomode,
-/*	.set_dmamode	= opti_set_dmamode, */
 	.tf_load	= ata_tf_load,
 	.tf_read	= ata_tf_read,
 	.check_status 	= ata_check_status,
@@ -267,7 +243,9 @@ static struct pci_driver opti_pci_driver = {
 	.name 		= DRV_NAME,
 	.id_table	= opti,
 	.probe 		= opti_init_one,
-	.remove		= ata_pci_remove_one
+	.remove		= ata_pci_remove_one,
+	.suspend	= ata_pci_device_suspend,
+	.resume		= ata_pci_device_resume,
 };
 
 static int __init opti_init(void)