ARM: imx: initial SolidRun HummingBoard support

Add support for the SolidRun HummingBoard.  This commit adds support for
the following interfaces on this board:

- Consumer Ir receiver
- S/PDIF output
- Both USB interfaces
- Gigabit Ethernet using AR8035
- UART port

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

5 files changed, 298 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index d57c1a65b24..875af333c6d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_MXC) += \
 	imx53-mba53.dtb \
 	imx53-qsb.dtb \
 	imx53-smd.dtb \
+	imx6dl-hummingboard.dtb \
 	imx6dl-sabreauto.dtb \
 	imx6dl-sabresd.dtb \
 	imx6dl-wandboard.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-hummingboard.dts b/arch/arm/boot/dts/imx6dl-hummingboard.dts
new file mode 100644
index 00000000000..fd8fc7cd53f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-hummingboard.dts
@@ -0,0 +1,167 @@
+/*
+ * Copyright (C) 2013,2014 Russell King
+ */
+/dts-v1/;
+
+#include "imx6dl.dtsi"
+#include "imx6qdl-microsom.dtsi"
+#include "imx6qdl-microsom-ar8035.dtsi"
+
+/ {
+	model = "SolidRun HummingBoard DL/Solo";
+	compatible = "solidrun,hummingboard", "fsl,imx6dl";
+
+	ir_recv: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio1 2 1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hummingboard_gpio1_2>;
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_3p3v: 3p3v {
+			compatible = "regulator-fixed";
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		reg_usbh1_vbus: usb-h1-vbus {
+			compatible = "regulator-fixed";
+			enable-active-high;
+			gpio = <&gpio1 0 0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_hummingboard_usbh1_vbus>;
+			regulator-name = "usb_h1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+
+		reg_usbotg_vbus: usb-otg-vbus {
+			compatible = "regulator-fixed";
+			enable-active-high;
+			gpio = <&gpio3 22 0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_hummingboard_usbotg_vbus>;
+			regulator-name = "usb_otg_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+	};
+
+	codec: spdif-transmitter {
+		compatible = "linux,spdif-dit";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_hummingboard_spdif>;
+	};
+
+	sound-spdif {
+		compatible = "fsl,imx-audio-spdif";
+		model = "imx-spdif";
+		/* IMX6 doesn't implement this yet */
+		spdif-controller = <&spdif>;
+		spdif-out;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hummingboard_flexcan1>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hummingboard_i2c1>;
+
+	/*
+	 * Not fitted on Carrier-1 board... yet
+	status = "okay";
+
+	rtc: pcf8523@68 {
+		compatible = "nxp,pcf8523";
+		reg = <0x68>;
+	};
+	 */
+};
+
+&iomuxc {
+	hummingboard {
+		pinctrl_hummingboard_flexcan1: hummingboard-flexcan1 {
+			fsl,pins = <
+				MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x80000000
+				MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x80000000
+			>;
+		};
+
+		pinctrl_hummingboard_gpio1_2: hummingboard-gpio1_2 {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000
+			>;
+		};
+
+		pinctrl_hummingboard_i2c1: hummingboard-i2c1 {
+			fsl,pins = <
+				MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+				MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+			>;
+		};
+
+		pinctrl_hummingboard_spdif: hummingboard-spdif {
+			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0>;
+		};
+
+		pinctrl_hummingboard_usbh1_vbus: hummingboard-usbh1-vbus {
+			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
+		};
+
+		pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
+			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
+		};
+
+		pinctrl_hummingboard_usdhc2_aux: hummingboard-usdhc2-aux {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_4__GPIO1_IO04    0x1f071
+			>;
+		};
+
+		pinctrl_hummingboard_usdhc2: hummingboard-usdhc2 {
+			fsl,pins = <
+				MX6QDL_PAD_SD2_CMD__SD2_CMD    0x17059
+				MX6QDL_PAD_SD2_CLK__SD2_CLK    0x10059
+				MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+				MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+				MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+				MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x13059
+			>;
+		};
+	};
+};
+
+&spdif {
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usbh1_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usbotg_vbus>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&pinctrl_hummingboard_usdhc2_aux
+		&pinctrl_hummingboard_usdhc2
+	>;
+	vmmc-supply = <&reg_3p3v>;
+	cd-gpios = <&gpio1 4 0>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi b/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
new file mode 100644
index 00000000000..a3cb2fff8f6
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
@@ -0,0 +1,62 @@
+/*
+ * Copyright (C) 2013,2014 Russell King
+ *
+ * This describes the hookup for an AR8035 to the iMX6 on the SolidRun
+ * MicroSOM.
+ */
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
+	phy-mode = "rgmii";
+	phy-reset-duration = <2>;
+	phy-reset-gpios = <&gpio4 15 0>;
+	status = "okay";
+};
+
+&iomuxc {
+	enet {
+		pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+				/* AR8035 reset */
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x130b0
+				/* AR8035 interrupt */
+				MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x80000000
+				/* GPIO16 -> AR8035 25MHz */
+				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0xc0000000
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x80000000
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
+				/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x0a0b1
+				/* AR8035 pin strapping: IO voltage: pull up */
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
+				/* AR8035 pin strapping: PHYADDR#0: pull down */
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x130b0
+				/* AR8035 pin strapping: PHYADDR#1: pull down */
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x130b0
+				/* AR8035 pin strapping: MODE#1: pull up */
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
+				/* AR8035 pin strapping: MODE#3: pull up */
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
+				/* AR8035 pin strapping: MODE#0: pull down */
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x130b0
+
+				/*
+				 * As the RMII pins are also connected to RGMII
+				 * so that an AR8030 can be placed, set these
+				 * to high-z with the same pulls as above.
+				 * Use the GPIO settings to avoid changing the
+				 * input select registers.
+				 */
+				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x03000
+				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x03000
+				MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x03000
+			>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-microsom.dtsi b/arch/arm/boot/dts/imx6qdl-microsom.dtsi
new file mode 100644
index 00000000000..d729d0b15f2
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-microsom.dtsi
@@ -0,0 +1,33 @@
+/*
+ * Copyright (C) 2013,2014 Russell King
+ */
+
+&iomuxc {
+	microsom {
+		pinctrl_microsom_uart1: microsom-uart1 {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
+				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
+			>;
+		};
+
+		pinctrl_microsom_usbotg: microsom-usbotg {
+			/*
+			 * Similar to pinctrl_usbotg_2, but we want it
+			 * pulled down for a fixed host connection.
+			 */
+			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_uart1>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_usbotg>;
+};
diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c
index d0cfb225ec9..cb6fa3d6124 100644
--- a/arch/arm/mach-imx/mach-imx6q.c
+++ b/arch/arm/mach-imx/mach-imx6q.c
@@ -103,6 +103,39 @@ static int ar8031_phy_fixup(struct phy_device *dev)
 
 #define PHY_ID_AR8031	0x004dd074
 
+static int ar8035_phy_fixup(struct phy_device *dev)
+{
+	u16 val;
+
+	/* Ar803x phy SmartEEE feature cause link status generates glitch,
+	 * which cause ethernet link down/up issue, so disable SmartEEE
+	 */
+	phy_write(dev, 0xd, 0x3);
+	phy_write(dev, 0xe, 0x805d);
+	phy_write(dev, 0xd, 0x4003);
+
+	val = phy_read(dev, 0xe);
+	phy_write(dev, 0xe, val & ~(1 << 8));
+
+	/*
+	 * Enable 125MHz clock from CLK_25M on the AR8031.  This
+	 * is fed in to the IMX6 on the ENET_REF_CLK (V22) pad.
+	 * Also, introduce a tx clock delay.
+	 *
+	 * This is the same as is the AR8031 fixup.
+	 */
+	ar8031_phy_fixup(dev);
+
+	/*check phy power*/
+	val = phy_read(dev, 0x0);
+	if (val & BMCR_PDOWN)
+		phy_write(dev, 0x0, val & ~BMCR_PDOWN);
+
+	return 0;
+}
+
+#define PHY_ID_AR8035 0x004dd072
+
 static void __init imx6q_enet_phy_init(void)
 {
 	if (IS_BUILTIN(CONFIG_PHYLIB)) {
@@ -112,6 +145,8 @@ static void __init imx6q_enet_phy_init(void)
 				ksz9031rn_phy_fixup);
 		phy_register_fixup_for_uid(PHY_ID_AR8031, 0xffffffff,
 				ar8031_phy_fixup);
+		phy_register_fixup_for_uid(PHY_ID_AR8035, 0xffffffef,
+				ar8035_phy_fixup);
 	}
 }