Merge tag 'boards2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc board updates from Olof Johansson:
 "This branch contains board updates, mostly for shmobile, but also a
  couple for PXA.

  The shmobile platforms are still in the early stages of DT enablement,
  so there's a bit more updates here than we'd ideally want to see:
   - regulator updates to provide some fixed regulators on several
     boards
   - gpio support updates for multiple boards
   - misc updates for recently-introduced boards armadillo800eva and
     kzm9g
   - defconfig updates"

* tag 'boards2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
  ARM: shmobile: kzm9g: defconfig enable INOTIFY_USER
  ARM: mach-shmobile: armadillo800eva: defconfig Allow use of armhf userspace
  ARM: shmobile: armadillo800eva: A3SP domain includes USB
  ARM: shmobile: armadillo800eva: A4LC domain includes LCDC
  ARM: shmobile: armadillo800eva: USB Func enables external IRQ mode
  ARM: mach-shmobile: kzm9d: Add defconfig
  ARM: mach-shmobile: select the fixed regulator driver on several boards
  ARM: mach-shmobile: add SDHI2 to the 2.8V fixed regulator consumers on kzm9g
  ARM: pxa: hx4700: Use DEFINE_RES_* macros consistently
  ARM: pxa: remove eseries.h
  ARM: mach-shmobile: add fixed voltage regulators to marzen
  ARM: mach-shmobile: add fixed voltage regulators to kzm9g
  ARM: mach-shmobile: add fixed voltage regulators to kzm9d
  ARM: mach-shmobile: add fixed voltage regulators to kota2
  ARM: mach-shmobile: add fixed voltage regulators to g4evm
  ARM: mach-shmobile: add fixed voltage regulators to bonito
  ARM: mach-shmobile: add fixed voltage regulators to armadillo800eva
  ARM: mach-shmobile: add fixed voltage regulators to ap4evb
  ARM: mach-shmobile: add fixed voltage regulators to ag5evm
  ARM: mach-shmobile: add 3.3V and 1.8V fixed regulators to mackerel
  ...

16 files changed, 1126 insertions, 153 deletions

diff --git a/arch/arm/configs/armadillo800eva_defconfig b/arch/arm/configs/armadillo800eva_defconfig
index ddc9fe6a78a..7d8718468e0 100644
--- a/arch/arm/configs/armadillo800eva_defconfig
+++ b/arch/arm/configs/armadillo800eva_defconfig
@@ -5,10 +5,7 @@ CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_UTS_NS is not set
 # CONFIG_IPC_NS is not set
-# CONFIG_USER_NS is not set
 # CONFIG_PID_NS is not set
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
@@ -21,7 +18,7 @@ CONFIG_ARCH_SHMOBILE=y
 CONFIG_ARCH_R8A7740=y
 CONFIG_MACH_ARMADILLO800EVA=y
 # CONFIG_SH_TIMER_TMU is not set
-# CONFIG_ARM_THUMB is not set
+CONFIG_ARM_THUMB=y
 CONFIG_CPU_BPREDICT_DISABLE=y
 # CONFIG_CACHE_L2X0 is not set
 CONFIG_ARM_ERRATA_430973=y
@@ -39,6 +36,7 @@ CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096"
 CONFIG_CMDLINE_FORCE=y
 CONFIG_KEXEC=y
+CONFIG_VFP=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
 # CONFIG_SUSPEND is not set
 CONFIG_NET=y
@@ -89,26 +87,32 @@ CONFIG_SERIAL_SH_SCI_CONSOLE=y
 CONFIG_I2C=y
 CONFIG_I2C_SH_MOBILE=y
 # CONFIG_HWMON is not set
+CONFIG_MEDIA_SUPPORT=y
+CONFIG_VIDEO_DEV=y
+# CONFIG_RC_CORE is not set
+# CONFIG_VIDEO_HELPER_CHIPS_AUTO is not set
+# CONFIG_V4L_USB_DRIVERS is not set
+CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SOC_CAMERA=y
+CONFIG_SOC_CAMERA_MT9T112=y
+CONFIG_VIDEO_SH_MOBILE_CEU=y
+# CONFIG_RADIO_ADAPTERS is not set
 CONFIG_FB=y
-CONFIG_FB_MODE_HELPERS=y
 CONFIG_FB_SH_MOBILE_LCDC=y
+CONFIG_FB_SH_MOBILE_HDMI=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
 CONFIG_LOGO=y
 # CONFIG_LOGO_LINUX_MONO is not set
 # CONFIG_LOGO_LINUX_VGA16 is not set
-CONFIG_SOUND=y
-CONFIG_SND=y
 # CONFIG_SND_SUPPORT_OLD_API is not set
 # CONFIG_SND_VERBOSE_PROCFS is not set
 # CONFIG_SND_DRIVERS is not set
 # CONFIG_SND_ARM is not set
-CONFIG_SND_SOC=y
 CONFIG_SND_SOC_SH4_FSI=y
 # CONFIG_HID_SUPPORT is not set
 CONFIG_USB=y
-# CONFIG_USB_DEVICE_CLASS is not set
 CONFIG_USB_RENESAS_USBHS=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_RENESAS_USBHS_UDC=y
@@ -116,6 +120,8 @@ CONFIG_USB_ETH=m
 CONFIG_MMC=y
 CONFIG_MMC_SDHI=y
 CONFIG_MMC_SH_MMCIF=y
+CONFIG_DMADEVICES=y
+CONFIG_SH_DMAE=y
 CONFIG_UIO=y
 CONFIG_UIO_PDRV_GENIRQ=y
 # CONFIG_DNOTIFY is not set
@@ -124,7 +130,6 @@ CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 # CONFIG_MISC_FILESYSTEMS is not set
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_NFS_V4_1=y
diff --git a/arch/arm/configs/kzm9d_defconfig b/arch/arm/configs/kzm9d_defconfig
new file mode 100644
index 00000000000..26146ffea1a
--- /dev/null
+++ b/arch/arm/configs/kzm9d_defconfig
@@ -0,0 +1,89 @@
+# CONFIG_ARM_PATCH_PHYS_VIRT is not set
+CONFIG_EXPERIMENTAL=y
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=16
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_EMBEDDED=y
+CONFIG_SLAB=y
+# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_IOSCHED_DEADLINE is not set
+# CONFIG_IOSCHED_CFQ is not set
+CONFIG_ARCH_SHMOBILE=y
+CONFIG_ARCH_EMEV2=y
+CONFIG_MACH_KZM9D=y
+CONFIG_MEMORY_START=0x40000000
+CONFIG_MEMORY_SIZE=0x10000000
+# CONFIG_SH_TIMER_TMU is not set
+# CONFIG_SWP_EMULATE is not set
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_SMP=y
+CONFIG_NR_CPUS=2
+CONFIG_HOTPLUG_CPU=y
+# CONFIG_LOCAL_TIMERS is not set
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+# CONFIG_CROSS_MEMORY_ATTACH is not set
+CONFIG_FORCE_MAX_ZONEORDER=13
+CONFIG_ZBOOT_ROM_TEXT=0x0
+CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_CMDLINE="console=tty0 console=ttyS1,115200n81 earlyprintk=serial8250-em.1,115200n81 mem=128M@0x40000000 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096"
+CONFIG_CMDLINE_FORCE=y
+CONFIG_VFP=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_SUSPEND is not set
+CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+# CONFIG_INET_DIAG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_WIRELESS is not set
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+# CONFIG_BLK_DEV is not set
+CONFIG_NETDEVICES=y
+# CONFIG_NET_VENDOR_BROADCOM is not set
+# CONFIG_NET_VENDOR_CHELSIO is not set
+# CONFIG_NET_VENDOR_CIRRUS is not set
+# CONFIG_NET_VENDOR_FARADAY is not set
+# CONFIG_NET_VENDOR_INTEL is not set
+# CONFIG_NET_VENDOR_MARVELL is not set
+# CONFIG_NET_VENDOR_MICREL is not set
+# CONFIG_NET_VENDOR_NATSEMI is not set
+# CONFIG_NET_VENDOR_SEEQ is not set
+CONFIG_SMSC911X=y
+# CONFIG_NET_VENDOR_STMICRO is not set
+# CONFIG_NET_VENDOR_WIZNET is not set
+# CONFIG_WLAN is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_8250=y
+CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_SERIAL_8250_EM=y
+# CONFIG_HW_RANDOM is not set
+CONFIG_GPIOLIB=y
+CONFIG_GPIO_EM=y
+# CONFIG_HWMON is not set
+# CONFIG_HID_SUPPORT is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_IOMMU_SUPPORT is not set
+# CONFIG_DNOTIFY is not set
+CONFIG_TMPFS=y
+# CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
+# CONFIG_FTRACE is not set
diff --git a/arch/arm/configs/kzm9g_defconfig b/arch/arm/configs/kzm9g_defconfig
index e3ebc20ed0a..2388c861062 100644
--- a/arch/arm/configs/kzm9g_defconfig
+++ b/arch/arm/configs/kzm9g_defconfig
@@ -100,7 +100,12 @@ CONFIG_SND_SOC_SH4_FSI=y
 CONFIG_USB=y
 CONFIG_USB_DEVICEFS=y
 CONFIG_USB_R8A66597_HCD=y
+CONFIG_USB_RENESAS_USBHS=y
 CONFIG_USB_STORAGE=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_RENESAS_USBHS_UDC=y
+CONFIG_USB_ETH=m
+CONFIG_USB_MASS_STORAGE=m
 CONFIG_MMC=y
 # CONFIG_MMC_BLOCK_BOUNCE is not set
 CONFIG_MMC_SDHI=y
@@ -108,12 +113,13 @@ CONFIG_MMC_SH_MMCIF=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_RS5C372=y
 CONFIG_DMADEVICES=y
 CONFIG_SH_DMAE=y
 CONFIG_ASYNC_TX_DMA=y
 CONFIG_STAGING=y
 # CONFIG_DNOTIFY is not set
-# CONFIG_INOTIFY_USER is not set
+CONFIG_INOTIFY_USER=y
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 # CONFIG_MISC_FILESYSTEMS is not set
diff --git a/arch/arm/mach-pxa/eseries.h b/arch/arm/mach-pxa/eseries.h
deleted file mode 100644
index b96949dd5ad..00000000000
--- a/arch/arm/mach-pxa/eseries.h
+++ /dev/null
@@ -1,14 +0,0 @@
-void __init eseries_fixup(struct tag *tags, char **cmdline, struct meminfo *mi);
-
-extern struct pxa2xx_udc_mach_info e7xx_udc_mach_info;
-extern struct pxaficp_platform_data e7xx_ficp_platform_data;
-extern int e7xx_irda_init(void);
-
-extern int eseries_tmio_enable(struct platform_device *dev);
-extern int eseries_tmio_disable(struct platform_device *dev);
-extern int eseries_tmio_suspend(struct platform_device *dev);
-extern int eseries_tmio_resume(struct platform_device *dev);
-extern void eseries_get_tmio_gpios(void);
-extern struct resource eseries_tmio_resources[];
-extern struct platform_device e300_tc6387xb_device;
-
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index d3de84b0dcb..e6311988add 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -296,27 +296,11 @@ static struct asic3_led asic3_leds[ASIC3_NUM_LEDS] = {
 
 static struct resource asic3_resources[] = {
 	/* GPIO part */
-	[0] = {
-		.start	= ASIC3_PHYS,
-		.end	= ASIC3_PHYS + ASIC3_MAP_SIZE_16BIT - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= PXA_GPIO_TO_IRQ(GPIO12_HX4700_ASIC3_IRQ),
-		.end	= PXA_GPIO_TO_IRQ(GPIO12_HX4700_ASIC3_IRQ),
-		.flags	= IORESOURCE_IRQ,
-	},
+	[0] = DEFINE_RES_MEM(ASIC3_PHYS, ASIC3_MAP_SIZE_16BIT),
+	[1] = DEFINE_RES_IRQ(PXA_GPIO_TO_IRQ(GPIO12_HX4700_ASIC3_IRQ)),
 	/* SD part */
-	[2] = {
-		.start	= ASIC3_SD_PHYS,
-		.end	= ASIC3_SD_PHYS + ASIC3_MAP_SIZE_16BIT - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[3] = {
-		.start	= PXA_GPIO_TO_IRQ(GPIO66_HX4700_ASIC3_nSDIO_IRQ),
-		.end	= PXA_GPIO_TO_IRQ(GPIO66_HX4700_ASIC3_nSDIO_IRQ),
-		.flags	= IORESOURCE_IRQ,
-	},
+	[2] = DEFINE_RES_MEM(ASIC3_SD_PHYS, ASIC3_MAP_SIZE_16BIT),
+	[3] = DEFINE_RES_IRQ(PXA_GPIO_TO_IRQ(GPIO66_HX4700_ASIC3_nSDIO_IRQ)),
 };
 
 static struct asic3_platform_data asic3_platform_data = {
@@ -343,11 +327,7 @@ static struct platform_device asic3 = {
  */
 
 static struct resource egpio_resources[] = {
-	[0] = {
-		.start = PXA_CS5_PHYS,
-		.end   = PXA_CS5_PHYS + 0x4 - 1,
-		.flags = IORESOURCE_MEM,
-	},
+	[0] = DEFINE_RES_MEM(PXA_CS5_PHYS, 0x4),
 };
 
 static struct htc_egpio_chip egpio_chips[] = {
@@ -537,11 +517,7 @@ static struct w100fb_mach_info w3220_info = {
 };
 
 static struct resource w3220_resources[] = {
-	[0] = {
-		.start	= ATI_W3220_PHYS,
-		.end	= ATI_W3220_PHYS + 0x00ffffff,
-		.flags	= IORESOURCE_MEM,
-	},
+	[0] = DEFINE_RES_MEM(ATI_W3220_PHYS, SZ_16M),
 };
 
 static struct platform_device w3220 = {
@@ -683,20 +659,12 @@ static struct pda_power_pdata power_supply_info = {
 };
 
 static struct resource power_supply_resources[] = {
-	[0] = {
-		.name  = "ac",
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE |
-		         IORESOURCE_IRQ_LOWEDGE,
-		.start = PXA_GPIO_TO_IRQ(GPIOD9_nAC_IN),
-		.end   = PXA_GPIO_TO_IRQ(GPIOD9_nAC_IN),
-	},
-	[1] = {
-		.name  = "usb",
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE |
-		         IORESOURCE_IRQ_LOWEDGE,
-		.start = PXA_GPIO_TO_IRQ(GPIOD14_nUSBC_DETECT),
-		.end   = PXA_GPIO_TO_IRQ(GPIOD14_nUSBC_DETECT),
-	},
+	[0] = DEFINE_RES_NAMED(PXA_GPIO_TO_IRQ(GPIOD9_nAC_IN), 1, "ac",
+		IORESOURCE_IRQ |
+		IORESOURCE_IRQ_HIGHEDGE | IORESOURCE_IRQ_LOWEDGE),
+	[1] = DEFINE_RES_NAMED(PXA_GPIO_TO_IRQ(GPIOD14_nUSBC_DETECT), 1, "usb",
+		IORESOURCE_IRQ |
+		IORESOURCE_IRQ_HIGHEDGE | IORESOURCE_IRQ_LOWEDGE),
 };
 
 static struct platform_device power_supply = {
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index eedb0d1888c..4cacc2d22fb 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -59,6 +59,7 @@ config MACH_G4EVM
 	bool "G4EVM board"
 	depends on ARCH_SH7377
 	select ARCH_REQUIRE_GPIOLIB
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 
 config MACH_AP4EVB
 	bool "AP4EVB board"
@@ -66,6 +67,7 @@ config MACH_AP4EVB
 	select ARCH_REQUIRE_GPIOLIB
 	select SH_LCD_MIPI_DSI
 	select SND_SOC_AK4642 if SND_SIMPLE_CARD
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 
 choice
 	prompt "AP4EVB LCD panel selection"
@@ -84,6 +86,7 @@ config MACH_AG5EVM
 	bool "AG5EVM board"
 	select ARCH_REQUIRE_GPIOLIB
 	select SH_LCD_MIPI_DSI
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	depends on ARCH_SH73A0
 
 config MACH_MACKEREL
@@ -91,15 +94,18 @@ config MACH_MACKEREL
 	depends on ARCH_SH7372
 	select ARCH_REQUIRE_GPIOLIB
 	select SND_SOC_AK4642 if SND_SIMPLE_CARD
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 
 config MACH_KOTA2
 	bool "KOTA2 board"
 	select ARCH_REQUIRE_GPIOLIB
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	depends on ARCH_SH73A0
 
 config MACH_BONITO
 	bool "bonito board"
 	select ARCH_REQUIRE_GPIOLIB
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 	depends on ARCH_R8A7740
 
 config MACH_ARMADILLO800EVA
@@ -107,22 +113,28 @@ config MACH_ARMADILLO800EVA
 	depends on ARCH_R8A7740
 	select ARCH_REQUIRE_GPIOLIB
 	select USE_OF
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
+	select SND_SOC_WM8978 if SND_SIMPLE_CARD
 
 config MACH_MARZEN
 	bool "MARZEN board"
 	depends on ARCH_R8A7779
 	select ARCH_REQUIRE_GPIOLIB
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 
 config MACH_KZM9D
 	bool "KZM9D board"
 	depends on ARCH_EMEV2
 	select USE_OF
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 
 config MACH_KZM9G
 	bool "KZM-A9-GT board"
 	depends on ARCH_SH73A0
 	select ARCH_REQUIRE_GPIOLIB
 	select USE_OF
+	select SND_SOC_AK4642 if SND_SIMPLE_CARD
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
 
 comment "SH-Mobile System Configuration"
 
diff --git a/arch/arm/mach-shmobile/board-ag5evm.c b/arch/arm/mach-shmobile/board-ag5evm.c
index 5a6f22f05e9..d82c010fdfc 100644
--- a/arch/arm/mach-shmobile/board-ag5evm.c
+++ b/arch/arm/mach-shmobile/board-ag5evm.c
@@ -27,6 +27,8 @@
 #include <linux/delay.h>
 #include <linux/io.h>
 #include <linux/dma-mapping.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/serial_sci.h>
 #include <linux/smsc911x.h>
 #include <linux/gpio.h>
@@ -52,6 +54,12 @@
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/traps.h>
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 static struct resource smsc9220_resources[] = {
 	[0] = {
 		.start		= 0x14000000,
@@ -142,6 +150,13 @@ static struct platform_device fsi_device = {
 	.resource	= fsi_resources,
 };
 
+/* Fixed 1.8V regulator to be used by MMCIF */
+static struct regulator_consumer_supply fixed1v8_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
+};
+
 static struct resource sh_mmcif_resources[] = {
 	[0] = {
 		.name	= "MMCIF",
@@ -364,6 +379,13 @@ static struct platform_device mipidsi0_device = {
 	},
 };
 
+/* Fixed 2.8V regulators to be used by SDHI0 */
+static struct regulator_consumer_supply fixed2v8_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+};
+
 /* SDHI0 */
 static struct sh_mobile_sdhi_info sdhi0_info = {
 	.dma_slave_tx	= SHDMA_SLAVE_SDHI0_TX,
@@ -408,8 +430,57 @@ static struct platform_device sdhi0_device = {
 	},
 };
 
-void ag5evm_sdhi1_set_pwr(struct platform_device *pdev, int state)
+/* Fixed 3.3V regulator to be used by SDHI1 */
+static struct regulator_consumer_supply cn4_power_consumers[] =
 {
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+};
+
+static struct regulator_init_data cn4_power_init_data = {
+	.constraints = {
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies  = ARRAY_SIZE(cn4_power_consumers),
+	.consumer_supplies      = cn4_power_consumers,
+};
+
+static struct fixed_voltage_config cn4_power_info = {
+	.supply_name = "CN4 SD/MMC Vdd",
+	.microvolts = 3300000,
+	.gpio = GPIO_PORT114,
+	.enable_high = 1,
+	.init_data = &cn4_power_init_data,
+};
+
+static struct platform_device cn4_power = {
+	.name = "reg-fixed-voltage",
+	.id   = 2,
+	.dev  = {
+		.platform_data = &cn4_power_info,
+	},
+};
+
+static void ag5evm_sdhi1_set_pwr(struct platform_device *pdev, int state)
+{
+	static int power_gpio = -EINVAL;
+
+	if (power_gpio < 0) {
+		int ret = gpio_request(GPIO_PORT114, "sdhi1_power");
+		if (!ret) {
+			power_gpio = GPIO_PORT114;
+			gpio_direction_output(power_gpio, 0);
+		}
+	}
+
+	/*
+	 * If requesting the GPIO above failed, it means, that the regulator got
+	 * probed and grabbed the GPIO, but we don't know, whether the sdhi
+	 * driver already uses the regulator. If it doesn't, we have to toggle
+	 * the GPIO ourselves, even though it is now owned by the fixed
+	 * regulator driver. We have to live with the race in case the driver
+	 * gets unloaded and the GPIO freed between these two steps.
+	 */
 	gpio_set_value(GPIO_PORT114, state);
 }
 
@@ -455,6 +526,7 @@ static struct platform_device sdhi1_device = {
 };
 
 static struct platform_device *ag5evm_devices[] __initdata = {
+	&cn4_power,
 	&eth_device,
 	&keysc_device,
 	&fsi_device,
@@ -468,6 +540,12 @@ static struct platform_device *ag5evm_devices[] __initdata = {
 
 static void __init ag5evm_init(void)
 {
+	regulator_register_always_on(0, "fixed-1.8V", fixed1v8_power_consumers,
+				     ARRAY_SIZE(fixed1v8_power_consumers), 1800000);
+	regulator_register_always_on(1, "fixed-2.8V", fixed2v8_power_consumers,
+				     ARRAY_SIZE(fixed2v8_power_consumers), 3300000);
+	regulator_register_fixed(3, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	sh73a0_pinmux_init();
 
 	/* enable SCIFA2 */
@@ -562,8 +640,6 @@ static void __init ag5evm_init(void)
 	gpio_request(GPIO_FN_SDHID1_2_PU, NULL);
 	gpio_request(GPIO_FN_SDHID1_1_PU, NULL);
 	gpio_request(GPIO_FN_SDHID1_0_PU, NULL);
-	gpio_request(GPIO_PORT114, "sdhi1_power");
-	gpio_direction_output(GPIO_PORT114, 0);
 
 #ifdef CONFIG_CACHE_L2X0
 	/* Shared attribute override enable, 64K*8way */
diff --git a/arch/arm/mach-shmobile/board-ap4evb.c b/arch/arm/mach-shmobile/board-ap4evb.c
index 7cac1df3085..f172ca85905 100644
--- a/arch/arm/mach-shmobile/board-ap4evb.c
+++ b/arch/arm/mach-shmobile/board-ap4evb.c
@@ -34,6 +34,8 @@
 #include <linux/i2c.h>
 #include <linux/i2c/tsc2007.h>
 #include <linux/io.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/sh_intc.h>
 #include <linux/sh_clk.h>
@@ -159,6 +161,27 @@
  * CN12: 3.3v
  */
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply fixed1v8_power_consumers[] =
+{
+	/* J22 default position: 1.8V */
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
+};
+
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+};
+
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 /* MTD */
 static struct mtd_partition nor_flash_partitions[] = {
 	{
@@ -1138,21 +1161,6 @@ static void __init fsi_init_pm_clock(void)
 	clk_put(fsia_ick);
 }
 
-/*
- * FIXME !!
- *
- * gpio_no_direction
- * are quick_hack.
- *
- * current gpio frame work doesn't have
- * the method to control only pull up/down/free.
- * this function should be replaced by correct gpio function
- */
-static void __init gpio_no_direction(u32 addr)
-{
-	__raw_writeb(0x00, addr);
-}
-
 /* TouchScreen */
 #ifdef CONFIG_AP4EVB_QHD
 # define GPIO_TSC_IRQ	GPIO_FN_IRQ28_123
@@ -1224,6 +1232,12 @@ static void __init ap4evb_init(void)
 	u32 srcr4;
 	struct clk *clk;
 
+	regulator_register_always_on(0, "fixed-1.8V", fixed1v8_power_consumers,
+				     ARRAY_SIZE(fixed1v8_power_consumers), 1800000);
+	regulator_register_always_on(1, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+	regulator_register_fixed(2, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	/* External clock source */
 	clk_set_rate(&sh7372_dv_clki_clk, 27000000);
 
@@ -1302,8 +1316,8 @@ static void __init ap4evb_init(void)
 
 	gpio_request(GPIO_PORT9, NULL);
 	gpio_request(GPIO_PORT10, NULL);
-	gpio_no_direction(GPIO_PORT9CR);  /* FSIAOBT needs no direction */
-	gpio_no_direction(GPIO_PORT10CR); /* FSIAOLR needs no direction */
+	gpio_direction_none(GPIO_PORT9CR);  /* FSIAOBT needs no direction */
+	gpio_direction_none(GPIO_PORT10CR); /* FSIAOLR needs no direction */
 
 	/* card detect pin for MMC slot (CN7) */
 	gpio_request(GPIO_PORT41, NULL);
diff --git a/arch/arm/mach-shmobile/board-armadillo800eva.c b/arch/arm/mach-shmobile/board-armadillo800eva.c
index d131e12c9ac..cf10f92856d 100644
--- a/arch/arm/mach-shmobile/board-armadillo800eva.c
+++ b/arch/arm/mach-shmobile/board-armadillo800eva.c
@@ -28,6 +28,8 @@
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
 #include <linux/gpio_keys.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/sh_eth.h>
 #include <linux/videodev2.h>
 #include <linux/usb/renesas_usbhs.h>
@@ -37,14 +39,20 @@
 #include <linux/mmc/sh_mobile_sdhi.h>
 #include <mach/common.h>
 #include <mach/irqs.h>
+#include <mach/r8a7740.h>
+#include <media/mt9t112.h>
+#include <media/sh_mobile_ceu.h>
+#include <media/soc_camera.h>
 #include <asm/page.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include <asm/mach/time.h>
 #include <asm/hardware/cache-l2x0.h>
-#include <mach/r8a7740.h>
 #include <video/sh_mobile_lcdc.h>
+#include <video/sh_mobile_hdmi.h>
+#include <sound/sh_fsi.h>
+#include <sound/simple_card.h>
 
 /*
  * CON1		Camera Module
@@ -108,6 +116,14 @@
  */
 
 /*
+ * FSI-WM8978
+ *
+ * this command is required when playback.
+ *
+ * # amixer set "Headphone" 50
+ */
+
+/*
  * USB function
  *
  * When you use USB Function,
@@ -117,14 +133,8 @@
  * These are a little bit complex.
  * see
  *	usbhsf_power_ctrl()
- *
- * CAUTION
- *
- * It uses autonomy mode for USB hotplug at this point
- * (= usbhs_private.platform_callback.get_vbus is NULL),
- * since we don't know what's happen on PM control
- * on this workaround.
  */
+#define IRQ7		evt2irq(0x02e0)
 #define USBCR1		0xe605810a
 #define USBH		0xC6700000
 #define USBH_USBCTR	0x10834
@@ -204,6 +214,20 @@ static void usbhsf_power_ctrl(struct platform_device *pdev,
 	}
 }
 
+static int usbhsf_get_vbus(struct platform_device *pdev)
+{
+	return gpio_get_value(GPIO_PORT209);
+}
+
+static irqreturn_t usbhsf_interrupt(int irq, void *data)
+{
+	struct platform_device *pdev = data;
+
+	renesas_usbhs_call_notify_hotplug(pdev);
+
+	return IRQ_HANDLED;
+}
+
 static void usbhsf_hardware_exit(struct platform_device *pdev)
 {
 	struct usbhsf_private *priv = usbhsf_get_priv(pdev);
@@ -227,11 +251,14 @@ static void usbhsf_hardware_exit(struct platform_device *pdev)
 	priv->host	= NULL;
 	priv->func	= NULL;
 	priv->usbh_base	= NULL;
+
+	free_irq(IRQ7, pdev);
 }
 
 static int usbhsf_hardware_init(struct platform_device *pdev)
 {
 	struct usbhsf_private *priv = usbhsf_get_priv(pdev);
+	int ret;
 
 	priv->phy	= clk_get(&pdev->dev, "phy");
 	priv->usb24	= clk_get(&pdev->dev, "usb24");
@@ -251,6 +278,14 @@ static int usbhsf_hardware_init(struct platform_device *pdev)
 		return -EIO;
 	}
 
+	ret = request_irq(IRQ7, usbhsf_interrupt, IRQF_TRIGGER_NONE,
+			  dev_name(&pdev->dev), pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "request_irq err\n");
+		return ret;
+	}
+	irq_set_irq_type(IRQ7, IRQ_TYPE_EDGE_BOTH);
+
 	/* usb24 use 1/1 of parent clock (= usb24s = 24MHz) */
 	clk_set_rate(priv->usb24,
 		     clk_get_rate(clk_get_parent(priv->usb24)));
@@ -262,6 +297,7 @@ static struct usbhsf_private usbhsf_private = {
 	.info = {
 		.platform_callback = {
 			.get_id		= usbhsf_get_id,
+			.get_vbus	= usbhsf_get_vbus,
 			.hardware_init	= usbhsf_hardware_init,
 			.hardware_exit	= usbhsf_hardware_exit,
 			.power_ctrl	= usbhsf_power_ctrl,
@@ -269,6 +305,8 @@ static struct usbhsf_private usbhsf_private = {
 		.driver_param = {
 			.buswait_bwait		= 5,
 			.detection_delay	= 5,
+			.d0_rx_id	= SHDMA_SLAVE_USBHS_RX,
+			.d1_tx_id	= SHDMA_SLAVE_USBHS_TX,
 		},
 	}
 };
@@ -384,6 +422,103 @@ static struct platform_device lcdc0_device = {
 	},
 };
 
+/*
+ * LCDC1/HDMI
+ */
+static struct sh_mobile_hdmi_info hdmi_info = {
+	.flags		= HDMI_OUTPUT_PUSH_PULL |
+			  HDMI_OUTPUT_POLARITY_HI |
+			  HDMI_32BIT_REG |
+			  HDMI_HAS_HTOP1 |
+			  HDMI_SND_SRC_SPDIF,
+};
+
+static struct resource hdmi_resources[] = {
+	[0] = {
+		.name	= "HDMI",
+		.start	= 0xe6be0000,
+		.end	= 0xe6be03ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0x1700),
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.name	= "HDMI emma3pf",
+		.start	= 0xe6be4000,
+		.end	= 0xe6be43ff,
+		.flags	= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device hdmi_device = {
+	.name		= "sh-mobile-hdmi",
+	.num_resources	= ARRAY_SIZE(hdmi_resources),
+	.resource	= hdmi_resources,
+	.id             = -1,
+	.dev	= {
+		.platform_data	= &hdmi_info,
+	},
+};
+
+static const struct fb_videomode lcdc1_mode = {
+	.name		= "HDMI 720p",
+	.xres		= 1280,
+	.yres		= 720,
+	.pixclock	= 13468,
+	.left_margin	= 220,
+	.right_margin	= 110,
+	.hsync_len	= 40,
+	.upper_margin	= 20,
+	.lower_margin	= 5,
+	.vsync_len	= 5,
+	.refresh	= 60,
+	.sync		= FB_SYNC_VERT_HIGH_ACT | FB_SYNC_HOR_HIGH_ACT,
+};
+
+static struct sh_mobile_lcdc_info hdmi_lcdc_info = {
+	.clock_source	= LCDC_CLK_PERIPHERAL, /* HDMI clock */
+	.ch[0] = {
+		.chan			= LCDC_CHAN_MAINLCD,
+		.fourcc			= V4L2_PIX_FMT_RGB565,
+		.interface_type		= RGB24,
+		.clock_divider		= 1,
+		.flags			= LCDC_FLAGS_DWPOL,
+		.lcd_modes		= &lcdc1_mode,
+		.num_modes		= 1,
+		.tx_dev			= &hdmi_device,
+		.panel_cfg = {
+			.width	= 1280,
+			.height = 720,
+		},
+	},
+};
+
+static struct resource hdmi_lcdc_resources[] = {
+	[0] = {
+		.name	= "LCDC1",
+		.start	= 0xfe944000,
+		.end	= 0xfe948000 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= intcs_evt2irq(0x1780),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device hdmi_lcdc_device = {
+	.name		= "sh_mobile_lcdc_fb",
+	.num_resources	= ARRAY_SIZE(hdmi_lcdc_resources),
+	.resource	= hdmi_lcdc_resources,
+	.id		= 1,
+	.dev	= {
+		.platform_data	= &hdmi_lcdc_info,
+		.coherent_dma_mask = ~0,
+	},
+};
+
 /* GPIO KEY */
 #define GPIO_KEY(c, g, d) { .code = c, .gpio = g, .desc = d, .active_low = 1 }
 
@@ -407,6 +542,17 @@ static struct platform_device gpio_keys_device = {
 	},
 };
 
+/* Fixed 3.3V regulator to be used by SDHI0, SDHI1, MMCIF */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vmmc", "sh_mmcif"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mmcif"),
+};
+
 /* SDHI0 */
 /*
  * FIXME
@@ -418,6 +564,8 @@ static struct platform_device gpio_keys_device = {
  */
 #define IRQ31	evt2irq(0x33E0)
 static struct sh_mobile_sdhi_info sdhi0_info = {
+	.dma_slave_tx	= SHDMA_SLAVE_SDHI0_TX,
+	.dma_slave_rx	= SHDMA_SLAVE_SDHI0_RX,
 	.tmio_caps	= MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ |\
 			  MMC_CAP_NEEDS_POLL,
 	.tmio_ocr_mask	= MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
@@ -458,6 +606,8 @@ static struct platform_device sdhi0_device = {
 
 /* SDHI1 */
 static struct sh_mobile_sdhi_info sdhi1_info = {
+	.dma_slave_tx	= SHDMA_SLAVE_SDHI1_TX,
+	.dma_slave_rx	= SHDMA_SLAVE_SDHI1_RX,
 	.tmio_caps	= MMC_CAP_SD_HIGHSPEED | MMC_CAP_SDIO_IRQ,
 	.tmio_ocr_mask	= MMC_VDD_165_195 | MMC_VDD_32_33 | MMC_VDD_33_34,
 	.tmio_flags	= TMIO_MMC_HAS_IDLE_WAIT,
@@ -532,12 +682,209 @@ static struct platform_device sh_mmcif_device = {
 	.resource	= sh_mmcif_resources,
 };
 
+/* Camera */
+static int mt9t111_power(struct device *dev, int mode)
+{
+	struct clk *mclk = clk_get(NULL, "video1");
+
+	if (IS_ERR(mclk)) {
+		dev_err(dev, "can't get video1 clock\n");
+		return -EINVAL;
+	}
+
+	if (mode) {
+		/* video1 (= CON1 camera) expect 24MHz */
+		clk_set_rate(mclk, clk_round_rate(mclk, 24000000));
+		clk_enable(mclk);
+		gpio_direction_output(GPIO_PORT158, 1);
+	} else {
+		gpio_direction_output(GPIO_PORT158, 0);
+		clk_disable(mclk);
+	}
+
+	clk_put(mclk);
+
+	return 0;
+}
+
+static struct i2c_board_info i2c_camera_mt9t111 = {
+	I2C_BOARD_INFO("mt9t112", 0x3d),
+};
+
+static struct mt9t112_camera_info mt9t111_info = {
+	.divider = { 16, 0, 0, 7, 0, 10, 14, 7, 7 },
+};
+
+static struct soc_camera_link mt9t111_link = {
+	.i2c_adapter_id	= 0,
+	.bus_id		= 0,
+	.board_info	= &i2c_camera_mt9t111,
+	.power		= mt9t111_power,
+	.priv		= &mt9t111_info,
+};
+
+static struct platform_device camera_device = {
+	.name	= "soc-camera-pdrv",
+	.id	= 0,
+	.dev	= {
+		.platform_data = &mt9t111_link,
+	},
+};
+
+/* CEU0 */
+static struct sh_mobile_ceu_info sh_mobile_ceu0_info = {
+	.flags = SH_CEU_FLAG_LOWER_8BIT,
+};
+
+static struct resource ceu0_resources[] = {
+	[0] = {
+		.name	= "CEU",
+		.start	= 0xfe910000,
+		.end	= 0xfe91009f,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = intcs_evt2irq(0x0500),
+		.flags  = IORESOURCE_IRQ,
+	},
+	[2] = {
+		/* place holder for contiguous memory */
+	},
+};
+
+static struct platform_device ceu0_device = {
+	.name		= "sh_mobile_ceu",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(ceu0_resources),
+	.resource	= ceu0_resources,
+	.dev	= {
+		.platform_data		= &sh_mobile_ceu0_info,
+		.coherent_dma_mask	= 0xffffffff,
+	},
+};
+
+/* FSI */
+static int fsi_hdmi_set_rate(struct device *dev, int rate, int enable)
+{
+	struct clk *fsib;
+	int ret;
+
+	/* it support 48KHz only */
+	if (48000 != rate)
+		return -EINVAL;
+
+	fsib = clk_get(dev, "ickb");
+	if (IS_ERR(fsib))
+		return -EINVAL;
+
+	if (enable) {
+		ret = SH_FSI_ACKMD_256 | SH_FSI_BPFMD_64;
+		clk_enable(fsib);
+	} else {
+		ret = 0;
+		clk_disable(fsib);
+	}
+
+	clk_put(fsib);
+
+	return ret;
+}
+
+static struct sh_fsi_platform_info fsi_info = {
+	/* FSI-WM8978 */
+	.port_a = {
+		.tx_id = SHDMA_SLAVE_FSIA_TX,
+	},
+	/* FSI-HDMI */
+	.port_b = {
+		.flags		= SH_FSI_FMT_SPDIF |
+				  SH_FSI_ENABLE_STREAM_MODE,
+		.set_rate	= fsi_hdmi_set_rate,
+		.tx_id		= SHDMA_SLAVE_FSIB_TX,
+	}
+};
+
+static struct resource fsi_resources[] = {
+	[0] = {
+		.name	= "FSI",
+		.start	= 0xfe1f0000,
+		.end	= 0xfe1f8400 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = evt2irq(0x1840),
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device fsi_device = {
+	.name		= "sh_fsi2",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(fsi_resources),
+	.resource	= fsi_resources,
+	.dev	= {
+		.platform_data	= &fsi_info,
+	},
+};
+
+/* FSI-WM8978 */
+static struct asoc_simple_dai_init_info fsi_wm8978_init_info = {
+	.fmt		= SND_SOC_DAIFMT_I2S,
+	.codec_daifmt	= SND_SOC_DAIFMT_CBM_CFM | SND_SOC_DAIFMT_NB_NF,
+	.cpu_daifmt	= SND_SOC_DAIFMT_CBS_CFS,
+	.sysclk		= 12288000,
+};
+
+static struct asoc_simple_card_info fsi_wm8978_info = {
+	.name		= "wm8978",
+	.card		= "FSI2A-WM8978",
+	.cpu_dai	= "fsia-dai",
+	.codec		= "wm8978.0-001a",
+	.platform	= "sh_fsi2",
+	.codec_dai	= "wm8978-hifi",
+	.init		= &fsi_wm8978_init_info,
+};
+
+static struct platform_device fsi_wm8978_device = {
+	.name	= "asoc-simple-card",
+	.id	= 0,
+	.dev	= {
+		.platform_data	= &fsi_wm8978_info,
+	},
+};
+
+/* FSI-HDMI */
+static struct asoc_simple_dai_init_info fsi2_hdmi_init_info = {
+	.cpu_daifmt	= SND_SOC_DAIFMT_CBM_CFM,
+};
+
+static struct asoc_simple_card_info fsi2_hdmi_info = {
+	.name		= "HDMI",
+	.card		= "FSI2B-HDMI",
+	.cpu_dai	= "fsib-dai",
+	.codec		= "sh-mobile-hdmi",
+	.platform	= "sh_fsi2",
+	.codec_dai	= "sh_mobile_hdmi-hifi",
+	.init		= &fsi2_hdmi_init_info,
+};
+
+static struct platform_device fsi_hdmi_device = {
+	.name	= "asoc-simple-card",
+	.id	= 1,
+	.dev	= {
+		.platform_data	= &fsi2_hdmi_info,
+	},
+};
+
 /* I2C */
 static struct i2c_board_info i2c0_devices[] = {
 	{
 		I2C_BOARD_INFO("st1232-ts", 0x55),
 		.irq = evt2irq(0x0340),
 	},
+	{
+		I2C_BOARD_INFO("wm8978", 0x1a),
+	},
 };
 
 /*
@@ -549,6 +896,13 @@ static struct platform_device *eva_devices[] __initdata = {
 	&sh_eth_device,
 	&sdhi0_device,
 	&sh_mmcif_device,
+	&hdmi_device,
+	&hdmi_lcdc_device,
+	&camera_device,
+	&ceu0_device,
+	&fsi_device,
+	&fsi_hdmi_device,
+	&fsi_wm8978_device,
 };
 
 static void __init eva_clock_init(void)
@@ -556,10 +910,14 @@ static void __init eva_clock_init(void)
 	struct clk *system	= clk_get(NULL, "system_clk");
 	struct clk *xtal1	= clk_get(NULL, "extal1");
 	struct clk *usb24s	= clk_get(NULL, "usb24s");
+	struct clk *fsibck	= clk_get(NULL, "fsibck");
+	struct clk *fsib	= clk_get(&fsi_device.dev, "ickb");
 
 	if (IS_ERR(system)	||
 	    IS_ERR(xtal1)	||
-	    IS_ERR(usb24s)) {
+	    IS_ERR(usb24s)	||
+	    IS_ERR(fsibck)	||
+	    IS_ERR(fsib)) {
 		pr_err("armadillo800eva board clock init failed\n");
 		goto clock_error;
 	}
@@ -570,6 +928,11 @@ static void __init eva_clock_init(void)
 	/* usb24s use extal1 (= system) clock (= 24MHz) */
 	clk_set_parent(usb24s, system);
 
+	/* FSIBCK is 12.288MHz, and it is parent of FSI-B */
+	clk_set_parent(fsib, fsibck);
+	clk_set_rate(fsibck, 12288000);
+	clk_set_rate(fsib,   12288000);
+
 clock_error:
 	if (!IS_ERR(system))
 		clk_put(system);
@@ -577,14 +940,23 @@ clock_error:
 		clk_put(xtal1);
 	if (!IS_ERR(usb24s))
 		clk_put(usb24s);
+	if (!IS_ERR(fsibck))
+		clk_put(fsibck);
+	if (!IS_ERR(fsib))
+		clk_put(fsib);
 }
 
 /*
  * board init
  */
+#define GPIO_PORT7CR	0xe6050007
+#define GPIO_PORT8CR	0xe6050008
 static void __init eva_init(void)
 {
-	eva_clock_init();
+	struct platform_device *usb = NULL;
+
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
 
 	r8a7740_pinmux_init();
 	r8a7740_meram_workaround();
@@ -668,8 +1040,19 @@ static void __init eva_init(void)
 		/* USB Host */
 	} else {
 		/* USB Func */
-		gpio_request(GPIO_FN_VBUS, NULL);
+		/*
+		 * A1 chip has 2 IRQ7 pin and it was controled by MSEL register.
+		 * OTOH, usbhs interrupt needs its value (HI/LOW) to decide
+		 * USB connection/disconnection (usbhsf_get_vbus()).
+		 * This means we needs to select GPIO_FN_IRQ7_PORT209 first,
+		 * and select GPIO_PORT209 here
+		 */
+		gpio_request(GPIO_FN_IRQ7_PORT209, NULL);
+		gpio_request(GPIO_PORT209, NULL);
+		gpio_direction_input(GPIO_PORT209);
+
 		platform_device_register(&usbhsf_device);
+		usb = &usbhsf_device;
 	}
 
 	/* SDHI0 */
@@ -707,6 +1090,48 @@ static void __init eva_init(void)
 	gpio_request(GPIO_FN_MMC1_D6_PORT143,	NULL);
 	gpio_request(GPIO_FN_MMC1_D7_PORT142,	NULL);
 
+	/* CEU0 */
+	gpio_request(GPIO_FN_VIO0_D7,		NULL);
+	gpio_request(GPIO_FN_VIO0_D6,		NULL);
+	gpio_request(GPIO_FN_VIO0_D5,		NULL);
+	gpio_request(GPIO_FN_VIO0_D4,		NULL);
+	gpio_request(GPIO_FN_VIO0_D3,		NULL);
+	gpio_request(GPIO_FN_VIO0_D2,		NULL);
+	gpio_request(GPIO_FN_VIO0_D1,		NULL);
+	gpio_request(GPIO_FN_VIO0_D0,		NULL);
+	gpio_request(GPIO_FN_VIO0_CLK,		NULL);
+	gpio_request(GPIO_FN_VIO0_HD,		NULL);
+	gpio_request(GPIO_FN_VIO0_VD,		NULL);
+	gpio_request(GPIO_FN_VIO0_FIELD,	NULL);
+	gpio_request(GPIO_FN_VIO_CKO,		NULL);
+
+	/* CON1/CON15 Camera */
+	gpio_request(GPIO_PORT173, NULL); /* STANDBY */
+	gpio_request(GPIO_PORT172, NULL); /* RST */
+	gpio_request(GPIO_PORT158, NULL); /* CAM_PON */
+	gpio_direction_output(GPIO_PORT173, 0);
+	gpio_direction_output(GPIO_PORT172, 1);
+	gpio_direction_output(GPIO_PORT158, 0); /* see mt9t111_power() */
+
+	/* FSI-WM8978 */
+	gpio_request(GPIO_FN_FSIAIBT,		NULL);
+	gpio_request(GPIO_FN_FSIAILR,		NULL);
+	gpio_request(GPIO_FN_FSIAOMC,		NULL);
+	gpio_request(GPIO_FN_FSIAOSLD,		NULL);
+	gpio_request(GPIO_FN_FSIAISLD_PORT5,	NULL);
+
+	gpio_request(GPIO_PORT7, NULL);
+	gpio_request(GPIO_PORT8, NULL);
+	gpio_direction_none(GPIO_PORT7CR); /* FSIAOBT needs no direction */
+	gpio_direction_none(GPIO_PORT8CR); /* FSIAOLR needs no direction */
+
+	/* FSI-HDMI */
+	gpio_request(GPIO_FN_FSIBCK,		NULL);
+
+	/* HDMI */
+	gpio_request(GPIO_FN_HDMI_HPD,		NULL);
+	gpio_request(GPIO_FN_HDMI_CEC,		NULL);
+
 	/*
 	 * CAUTION
 	 *
@@ -753,6 +1178,13 @@ static void __init eva_init(void)
 
 	platform_add_devices(eva_devices,
 			     ARRAY_SIZE(eva_devices));
+
+	eva_clock_init();
+
+	rmobile_add_device_to_domain(&r8a7740_pd_a4lc, &lcdc0_device);
+	rmobile_add_device_to_domain(&r8a7740_pd_a4lc, &hdmi_lcdc_device);
+	if (usb)
+		rmobile_add_device_to_domain(&r8a7740_pd_a3sp, usb);
 }
 
 static void __init eva_earlytimer_init(void)
diff --git a/arch/arm/mach-shmobile/board-bonito.c b/arch/arm/mach-shmobile/board-bonito.c
index e9b32cfbf74..4129008eae2 100644
--- a/arch/arm/mach-shmobile/board-bonito.c
+++ b/arch/arm/mach-shmobile/board-bonito.c
@@ -26,6 +26,8 @@
 #include <linux/irq.h>
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/videodev2.h>
 #include <mach/common.h>
@@ -75,6 +77,12 @@
  * S38.2 = OFF
  */
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 /*
  * FPGA
  */
@@ -360,6 +368,8 @@ static void __init bonito_init(void)
 {
 	u16 val;
 
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	r8a7740_pinmux_init();
 	bonito_fpga_init();
 
diff --git a/arch/arm/mach-shmobile/board-g4evm.c b/arch/arm/mach-shmobile/board-g4evm.c
index f1257321999..fa5dfc5c8ed 100644
--- a/arch/arm/mach-shmobile/board-g4evm.c
+++ b/arch/arm/mach-shmobile/board-g4evm.c
@@ -26,6 +26,8 @@
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/physmap.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/usb/r8a66597.h>
 #include <linux/io.h>
 #include <linux/input.h>
@@ -196,6 +198,15 @@ static struct platform_device keysc_device = {
 	},
 };
 
+/* Fixed 3.3V regulator to be used by SDHI0 and SDHI1 */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+};
+
 /* SDHI */
 static struct sh_mobile_sdhi_info sdhi0_info = {
 	.tmio_caps	= MMC_CAP_SDIO_IRQ,
@@ -271,26 +282,11 @@ static struct platform_device *g4evm_devices[] __initdata = {
 #define GPIO_SDHID1_D3	0xe6052106
 #define GPIO_SDHICMD1	0xe6052107
 
-/*
- * FIXME !!
- *
- * gpio_pull_up is quick_hack.
- *
- * current gpio frame work doesn't have
- * the method to control only pull up/down/free.
- * this function should be replaced by correct gpio function
- */
-static void __init gpio_pull_up(u32 addr)
-{
-	u8 data = __raw_readb(addr);
-
-	data &= 0x0F;
-	data |= 0xC0;
-	__raw_writeb(data, addr);
-}
-
 static void __init g4evm_init(void)
 {
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+
 	sh7377_pinmux_init();
 
 	/* Lit DS14 LED */
@@ -351,11 +347,11 @@ static void __init g4evm_init(void)
 	gpio_request(GPIO_FN_SDHID0_3, NULL);
 	gpio_request(GPIO_FN_SDHICMD0, NULL);
 	gpio_request(GPIO_FN_SDHIWP0, NULL);
-	gpio_pull_up(GPIO_SDHID0_D0);
-	gpio_pull_up(GPIO_SDHID0_D1);
-	gpio_pull_up(GPIO_SDHID0_D2);
-	gpio_pull_up(GPIO_SDHID0_D3);
-	gpio_pull_up(GPIO_SDHICMD0);
+	gpio_request_pullup(GPIO_SDHID0_D0);
+	gpio_request_pullup(GPIO_SDHID0_D1);
+	gpio_request_pullup(GPIO_SDHID0_D2);
+	gpio_request_pullup(GPIO_SDHID0_D3);
+	gpio_request_pullup(GPIO_SDHICMD0);
 
 	/* SDHI1 */
 	gpio_request(GPIO_FN_SDHICLK1, NULL);
@@ -364,11 +360,11 @@ static void __init g4evm_init(void)
 	gpio_request(GPIO_FN_SDHID1_2, NULL);
 	gpio_request(GPIO_FN_SDHID1_3, NULL);
 	gpio_request(GPIO_FN_SDHICMD1, NULL);
-	gpio_pull_up(GPIO_SDHID1_D0);
-	gpio_pull_up(GPIO_SDHID1_D1);
-	gpio_pull_up(GPIO_SDHID1_D2);
-	gpio_pull_up(GPIO_SDHID1_D3);
-	gpio_pull_up(GPIO_SDHICMD1);
+	gpio_request_pullup(GPIO_SDHID1_D0);
+	gpio_request_pullup(GPIO_SDHID1_D1);
+	gpio_request_pullup(GPIO_SDHID1_D2);
+	gpio_request_pullup(GPIO_SDHID1_D3);
+	gpio_request_pullup(GPIO_SDHICMD1);
 
 	sh7377_add_standard_devices();
 
diff --git a/arch/arm/mach-shmobile/board-kota2.c b/arch/arm/mach-shmobile/board-kota2.c
index f60f1b281cc..21dbe54304d 100644
--- a/arch/arm/mach-shmobile/board-kota2.c
+++ b/arch/arm/mach-shmobile/board-kota2.c
@@ -27,6 +27,8 @@
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 #include <linux/io.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/gpio.h>
 #include <linux/input.h>
@@ -49,6 +51,12 @@
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/traps.h>
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 /* SMSC 9220 */
 static struct resource smsc9220_resources[] = {
 	[0] = {
@@ -288,6 +296,13 @@ static struct platform_device leds_tpu30_device = {
 	.resource	= tpu30_resources,
 };
 
+/* Fixed 1.8V regulator to be used by MMCIF */
+static struct regulator_consumer_supply fixed1v8_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
+};
+
 /* MMCIF */
 static struct resource mmcif_resources[] = {
 	[0] = {
@@ -321,6 +336,15 @@ static struct platform_device mmcif_device = {
 	.resource       = mmcif_resources,
 };
 
+/* Fixed 3.3V regulator to be used by SDHI0 and SDHI1 */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+};
+
 /* SDHI0 */
 static struct sh_mobile_sdhi_info sdhi0_info = {
 	.tmio_caps      = MMC_CAP_SD_HIGHSPEED,
@@ -411,6 +435,12 @@ static struct platform_device *kota2_devices[] __initdata = {
 
 static void __init kota2_init(void)
 {
+	regulator_register_always_on(0, "fixed-1.8V", fixed1v8_power_consumers,
+				     ARRAY_SIZE(fixed1v8_power_consumers), 1800000);
+	regulator_register_always_on(1, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+	regulator_register_fixed(2, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	sh73a0_pinmux_init();
 
 	/* SCIFA2 (UART2) */
diff --git a/arch/arm/mach-shmobile/board-kzm9d.c b/arch/arm/mach-shmobile/board-kzm9d.c
index 6a33cf39342..2c986eaae7b 100644
--- a/arch/arm/mach-shmobile/board-kzm9d.c
+++ b/arch/arm/mach-shmobile/board-kzm9d.c
@@ -21,6 +21,8 @@
 #include <linux/kernel.h>
 #include <linux/interrupt.h>
 #include <linux/platform_device.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <mach/common.h>
 #include <mach/emev2.h>
@@ -28,6 +30,12 @@
 #include <asm/mach/arch.h>
 #include <asm/hardware/gic.h>
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 /* Ether */
 static struct resource smsc911x_resources[] = {
 	[0] = {
@@ -63,6 +71,8 @@ static struct platform_device *kzm9d_devices[] __initdata = {
 
 void __init kzm9d_add_standard_devices(void)
 {
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	emev2_add_standard_devices();
 
 	platform_add_devices(kzm9d_devices, ARRAY_SIZE(kzm9d_devices));
diff --git a/arch/arm/mach-shmobile/board-kzm9g.c b/arch/arm/mach-shmobile/board-kzm9g.c
index c0ae815e7be..53b7ea92c32 100644
--- a/arch/arm/mach-shmobile/board-kzm9g.c
+++ b/arch/arm/mach-shmobile/board-kzm9g.c
@@ -30,9 +30,14 @@
 #include <linux/mmc/sh_mobile_sdhi.h>
 #include <linux/mfd/tmio.h>
 #include <linux/platform_device.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/usb/r8a66597.h>
+#include <linux/usb/renesas_usbhs.h>
 #include <linux/videodev2.h>
+#include <sound/sh_fsi.h>
+#include <sound/simple_card.h>
 #include <mach/irqs.h>
 #include <mach/sh73a0.h>
 #include <mach/common.h>
@@ -54,6 +59,20 @@
 #define GPIO_PCF8575_PORT15	(GPIO_NR + 13)
 #define GPIO_PCF8575_PORT16	(GPIO_NR + 14)
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
+/*
+ * FSI-AK4648
+ *
+ * this command is required when playback.
+ *
+ * # amixer set "LINEOUT Mixer DACL" on
+ */
+
 /* SMSC 9221 */
 static struct resource smsc9221_resources[] = {
 	[0] = {
@@ -112,6 +131,151 @@ static struct platform_device usb_host_device = {
 	.resource	= usb_resources,
 };
 
+/* USB Func CN17 */
+struct usbhs_private {
+	unsigned int phy;
+	unsigned int cr2;
+	struct renesas_usbhs_platform_info info;
+};
+
+#define IRQ15			intcs_evt2irq(0x03e0)
+#define USB_PHY_MODE		(1 << 4)
+#define USB_PHY_INT_EN		((1 << 3) | (1 << 2))
+#define USB_PHY_ON		(1 << 1)
+#define USB_PHY_OFF		(1 << 0)
+#define USB_PHY_INT_CLR		(USB_PHY_ON | USB_PHY_OFF)
+
+#define usbhs_get_priv(pdev) \
+	container_of(renesas_usbhs_get_info(pdev), struct usbhs_private, info)
+
+static int usbhs_get_vbus(struct platform_device *pdev)
+{
+	struct usbhs_private *priv = usbhs_get_priv(pdev);
+
+	return !((1 << 7) & __raw_readw(priv->cr2));
+}
+
+static void usbhs_phy_reset(struct platform_device *pdev)
+{
+	struct usbhs_private *priv = usbhs_get_priv(pdev);
+
+	/* init phy */
+	__raw_writew(0x8a0a, priv->cr2);
+}
+
+static int usbhs_get_id(struct platform_device *pdev)
+{
+	return USBHS_GADGET;
+}
+
+static irqreturn_t usbhs_interrupt(int irq, void *data)
+{
+	struct platform_device *pdev = data;
+	struct usbhs_private *priv = usbhs_get_priv(pdev);
+
+	renesas_usbhs_call_notify_hotplug(pdev);
+
+	/* clear status */
+	__raw_writew(__raw_readw(priv->phy) | USB_PHY_INT_CLR, priv->phy);
+
+	return IRQ_HANDLED;
+}
+
+static int usbhs_hardware_init(struct platform_device *pdev)
+{
+	struct usbhs_private *priv = usbhs_get_priv(pdev);
+	int ret;
+
+	/* clear interrupt status */
+	__raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->phy);
+
+	ret = request_irq(IRQ15, usbhs_interrupt, IRQF_TRIGGER_HIGH,
+			  dev_name(&pdev->dev), pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "request_irq err\n");
+		return ret;
+	}
+
+	/* enable USB phy interrupt */
+	__raw_writew(USB_PHY_MODE | USB_PHY_INT_EN, priv->phy);
+
+	return 0;
+}
+
+static void usbhs_hardware_exit(struct platform_device *pdev)
+{
+	struct usbhs_private *priv = usbhs_get_priv(pdev);
+
+	/* clear interrupt status */
+	__raw_writew(USB_PHY_MODE | USB_PHY_INT_CLR, priv->phy);
+
+	free_irq(IRQ15, pdev);
+}
+
+static u32 usbhs_pipe_cfg[] = {
+	USB_ENDPOINT_XFER_CONTROL,
+	USB_ENDPOINT_XFER_ISOC,
+	USB_ENDPOINT_XFER_ISOC,
+	USB_ENDPOINT_XFER_BULK,
+	USB_ENDPOINT_XFER_BULK,
+	USB_ENDPOINT_XFER_BULK,
+	USB_ENDPOINT_XFER_INT,
+	USB_ENDPOINT_XFER_INT,
+	USB_ENDPOINT_XFER_INT,
+	USB_ENDPOINT_XFER_BULK,
+	USB_ENDPOINT_XFER_BULK,
+	USB_ENDPOINT_XFER_BULK,
+	USB_ENDPOINT_XFER_BULK,
+	USB_ENDPOINT_XFER_BULK,
+	USB_ENDPOINT_XFER_BULK,
+	USB_ENDPOINT_XFER_BULK,
+};
+
+static struct usbhs_private usbhs_private = {
+	.phy	= 0xe60781e0,		/* USBPHYINT */
+	.cr2	= 0xe605810c,		/* USBCR2 */
+	.info = {
+		.platform_callback = {
+			.hardware_init	= usbhs_hardware_init,
+			.hardware_exit	= usbhs_hardware_exit,
+			.get_id		= usbhs_get_id,
+			.phy_reset	= usbhs_phy_reset,
+			.get_vbus	= usbhs_get_vbus,
+		},
+		.driver_param = {
+			.buswait_bwait	= 4,
+			.has_otg	= 1,
+			.pipe_type	= usbhs_pipe_cfg,
+			.pipe_size	= ARRAY_SIZE(usbhs_pipe_cfg),
+		},
+	},
+};
+
+static struct resource usbhs_resources[] = {
+	[0] = {
+		.start	= 0xE6890000,
+		.end	= 0xE68900e6 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= gic_spi(62),
+		.end	= gic_spi(62),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device usbhs_device = {
+	.name	= "renesas_usbhs",
+	.id	= -1,
+	.dev = {
+		.dma_mask		= NULL,
+		.coherent_dma_mask	= 0xffffffff,
+		.platform_data		= &usbhs_private.info,
+	},
+	.num_resources	= ARRAY_SIZE(usbhs_resources),
+	.resource	= usbhs_resources,
+};
+
 /* LCDC */
 static struct fb_videomode kzm_lcdc_mode = {
 	.name		= "WVGA Panel",
@@ -166,6 +330,13 @@ static struct platform_device lcdc_device = {
 	},
 };
 
+/* Fixed 1.8V regulator to be used by MMCIF */
+static struct regulator_consumer_supply fixed1v8_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
+};
+
 /* MMCIF */
 static struct resource sh_mmcif_resources[] = {
 	[0] = {
@@ -187,6 +358,8 @@ static struct resource sh_mmcif_resources[] = {
 static struct sh_mmcif_plat_data sh_mmcif_platdata = {
 	.ocr		= MMC_VDD_165_195,
 	.caps		= MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE,
+	.slave_id_tx	= SHDMA_SLAVE_MMCIF_TX,
+	.slave_id_rx	= SHDMA_SLAVE_MMCIF_RX,
 };
 
 static struct platform_device mmc_device = {
@@ -200,6 +373,15 @@ static struct platform_device mmc_device = {
 	.resource	= sh_mmcif_resources,
 };
 
+/* Fixed 2.8V regulators to be used by SDHI0 and SDHI2 */
+static struct regulator_consumer_supply fixed2v8_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.2"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.2"),
+};
+
 /* SDHI */
 static struct sh_mobile_sdhi_info sdhi0_info = {
 	.tmio_flags	= TMIO_MMC_HAS_IDLE_WAIT,
@@ -240,6 +422,50 @@ static struct platform_device sdhi0_device = {
 	},
 };
 
+/* Micro SD */
+static struct sh_mobile_sdhi_info sdhi2_info = {
+	.tmio_flags	= TMIO_MMC_HAS_IDLE_WAIT |
+			  TMIO_MMC_USE_GPIO_CD |
+			  TMIO_MMC_WRPROTECT_DISABLE,
+	.tmio_caps	= MMC_CAP_SD_HIGHSPEED,
+	.tmio_ocr_mask	= MMC_VDD_27_28 | MMC_VDD_28_29,
+	.cd_gpio	= GPIO_PORT13,
+};
+
+static struct resource sdhi2_resources[] = {
+	[0] = {
+		.name	= "SDHI2",
+		.start	= 0xee140000,
+		.end	= 0xee1400ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.name	= SH_MOBILE_SDHI_IRQ_CARD_DETECT,
+		.start	= gic_spi(103),
+		.flags	= IORESOURCE_IRQ,
+	},
+	[2] = {
+		.name	= SH_MOBILE_SDHI_IRQ_SDCARD,
+		.start	= gic_spi(104),
+		.flags	= IORESOURCE_IRQ,
+	},
+	[3] = {
+		.name	= SH_MOBILE_SDHI_IRQ_SDIO,
+		.start	= gic_spi(105),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device sdhi2_device = {
+	.name		= "sh_mobile_sdhi",
+	.id		= 2,
+	.num_resources	= ARRAY_SIZE(sdhi2_resources),
+	.resource	= sdhi2_resources,
+	.dev	= {
+		.platform_data	= &sdhi2_info,
+	},
+};
+
 /* KEY */
 #define GPIO_KEY(c, g, d) { .code = c, .gpio = g, .desc = d, .active_low = 1 }
 
@@ -267,11 +493,74 @@ static struct platform_device gpio_keys_device = {
 	},
 };
 
+/* FSI-AK4648 */
+static struct sh_fsi_platform_info fsi_info = {
+	.port_a = {
+		.tx_id = SHDMA_SLAVE_FSI2A_TX,
+	},
+};
+
+static struct resource fsi_resources[] = {
+	[0] = {
+		.name	= "FSI",
+		.start	= 0xEC230000,
+		.end	= 0xEC230400 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = gic_spi(146),
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device fsi_device = {
+	.name		= "sh_fsi2",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(fsi_resources),
+	.resource	= fsi_resources,
+	.dev	= {
+		.platform_data	= &fsi_info,
+	},
+};
+
+static struct asoc_simple_dai_init_info fsi2_ak4648_init_info = {
+	.fmt		= SND_SOC_DAIFMT_LEFT_J,
+	.codec_daifmt	= SND_SOC_DAIFMT_CBM_CFM,
+	.cpu_daifmt	= SND_SOC_DAIFMT_CBS_CFS,
+	.sysclk		= 11289600,
+};
+
+static struct asoc_simple_card_info fsi2_ak4648_info = {
+	.name		= "AK4648",
+	.card		= "FSI2A-AK4648",
+	.cpu_dai	= "fsia-dai",
+	.codec		= "ak4642-codec.0-0012",
+	.platform	= "sh_fsi2",
+	.codec_dai	= "ak4642-hifi",
+	.init		= &fsi2_ak4648_init_info,
+};
+
+static struct platform_device fsi_ak4648_device = {
+	.name	= "asoc-simple-card",
+	.dev	= {
+		.platform_data	= &fsi2_ak4648_info,
+	},
+};
+
 /* I2C */
 static struct pcf857x_platform_data pcf8575_pdata = {
 	.gpio_base	= GPIO_PCF8575_BASE,
 };
 
+static struct i2c_board_info i2c0_devices[] = {
+	{
+		I2C_BOARD_INFO("ak4648", 0x12),
+	},
+	{
+		I2C_BOARD_INFO("r2025sd", 0x32),
+	}
+};
+
 static struct i2c_board_info i2c1_devices[] = {
 	{
 		I2C_BOARD_INFO("st1232-ts", 0x55),
@@ -289,10 +578,14 @@ static struct i2c_board_info i2c3_devices[] = {
 static struct platform_device *kzm_devices[] __initdata = {
 	&smsc_device,
 	&usb_host_device,
+	&usbhs_device,
 	&lcdc_device,
 	&mmc_device,
 	&sdhi0_device,
+	&sdhi2_device,
 	&gpio_keys_device,
+	&fsi_device,
+	&fsi_ak4648_device,
 };
 
 /*
@@ -350,6 +643,12 @@ device_initcall(as3711_enable_lcdc_backlight);
 
 static void __init kzm_init(void)
 {
+	regulator_register_always_on(0, "fixed-1.8V", fixed1v8_power_consumers,
+				     ARRAY_SIZE(fixed1v8_power_consumers), 1800000);
+	regulator_register_always_on(1, "fixed-2.8V", fixed2v8_power_consumers,
+				     ARRAY_SIZE(fixed2v8_power_consumers), 2800000);
+	regulator_register_fixed(2, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	sh73a0_pinmux_init();
 
 	/* enable SCIFA4 */
@@ -427,15 +726,36 @@ static void __init kzm_init(void)
 	gpio_request(GPIO_PORT15, NULL);
 	gpio_direction_output(GPIO_PORT15, 1); /* power */
 
+	/* enable Micro SD */
+	gpio_request(GPIO_FN_SDHID2_0,		NULL);
+	gpio_request(GPIO_FN_SDHID2_1,		NULL);
+	gpio_request(GPIO_FN_SDHID2_2,		NULL);
+	gpio_request(GPIO_FN_SDHID2_3,		NULL);
+	gpio_request(GPIO_FN_SDHICMD2,		NULL);
+	gpio_request(GPIO_FN_SDHICLK2,		NULL);
+	gpio_request(GPIO_PORT14, NULL);
+	gpio_direction_output(GPIO_PORT14, 1); /* power */
+
 	/* I2C 3 */
 	gpio_request(GPIO_FN_PORT27_I2C_SCL3, NULL);
 	gpio_request(GPIO_FN_PORT28_I2C_SDA3, NULL);
 
+	/* enable FSI2 port A (ak4648) */
+	gpio_request(GPIO_FN_FSIACK,	NULL);
+	gpio_request(GPIO_FN_FSIAILR,	NULL);
+	gpio_request(GPIO_FN_FSIAIBT,	NULL);
+	gpio_request(GPIO_FN_FSIAISLD,	NULL);
+	gpio_request(GPIO_FN_FSIAOSLD,	NULL);
+
+	/* enable USB */
+	gpio_request(GPIO_FN_VBUS_0,	NULL);
+
 #ifdef CONFIG_CACHE_L2X0
 	/* Early BRESP enable, Shared attribute override enable, 64K*8way */
 	l2x0_init(IOMEM(0xf0100000), 0x40460000, 0x82000fff);
 #endif
 
+	i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices));
 	i2c_register_board_info(1, i2c1_devices, ARRAY_SIZE(i2c1_devices));
 	i2c_register_board_info(3, i2c3_devices, ARRAY_SIZE(i2c3_devices));
 
diff --git a/arch/arm/mach-shmobile/board-mackerel.c b/arch/arm/mach-shmobile/board-mackerel.c
index 9640f34122b..7ea2b31e319 100644
--- a/arch/arm/mach-shmobile/board-mackerel.c
+++ b/arch/arm/mach-shmobile/board-mackerel.c
@@ -41,6 +41,8 @@
 #include <linux/mtd/physmap.h>
 #include <linux/mtd/sh_flctl.h>
 #include <linux/pm_clock.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <linux/sh_intc.h>
 #include <linux/tca6416_keypad.h>
@@ -203,31 +205,32 @@
  * amixer set "HPOUTR Mixer DACH" on
  */
 
-/*
- * FIXME !!
- *
- * gpio_no_direction
- * gpio_pull_down
- * are quick_hack.
- *
- * current gpio frame work doesn't have
- * the method to control only pull up/down/free.
- * this function should be replaced by correct gpio function
- */
-static void __init gpio_no_direction(u32 addr)
+/* Fixed 3.3V and 1.8V regulators to be used by multiple devices */
+static struct regulator_consumer_supply fixed1v8_power_consumers[] =
 {
-	__raw_writeb(0x00, addr);
-}
+	/*
+	 * J22 on mackerel switches mmcif.0 and sdhi.1 between 1.8V and 3.3V
+	 * Since we cannot support both voltages, we support the default 1.8V
+	 */
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.1"),
+	REGULATOR_SUPPLY("vmmc", "sh_mmcif.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mmcif.0"),
+};
 
-static void __init gpio_pull_down(u32 addr)
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
 {
-	u8 data = __raw_readb(addr);
-
-	data &= 0x0F;
-	data |= 0xA0;
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.2"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.2"),
+};
 
-	__raw_writeb(data, addr);
-}
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
 
 /* MTD */
 static struct mtd_partition nor_flash_partitions[] = {
@@ -1409,6 +1412,12 @@ static void __init mackerel_init(void)
 	u32 srcr4;
 	struct clk *clk;
 
+	regulator_register_always_on(0, "fixed-1.8V", fixed1v8_power_consumers,
+				     ARRAY_SIZE(fixed1v8_power_consumers), 1800000);
+	regulator_register_always_on(1, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+	regulator_register_fixed(2, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	/* External clock source */
 	clk_set_rate(&sh7372_dv_clki_clk, 27000000);
 
@@ -1458,11 +1467,11 @@ static void __init mackerel_init(void)
 
 	/* USBHS0 */
 	gpio_request(GPIO_FN_VBUS0_0, NULL);
-	gpio_pull_down(GPIO_PORT168CR); /* VBUS0_0 pull down */
+	gpio_request_pulldown(GPIO_PORT168CR); /* VBUS0_0 pull down */
 
 	/* USBHS1 */
 	gpio_request(GPIO_FN_VBUS0_1, NULL);
-	gpio_pull_down(GPIO_PORT167CR); /* VBUS0_1 pull down */
+	gpio_request_pulldown(GPIO_PORT167CR); /* VBUS0_1 pull down */
 	gpio_request(GPIO_FN_IDIN_1_113, NULL);
 
 	/* enable FSI2 port A (ak4643) */
@@ -1475,8 +1484,8 @@ static void __init mackerel_init(void)
 
 	gpio_request(GPIO_PORT9,  NULL);
 	gpio_request(GPIO_PORT10, NULL);
-	gpio_no_direction(GPIO_PORT9CR);  /* FSIAOBT needs no direction */
-	gpio_no_direction(GPIO_PORT10CR); /* FSIAOLR needs no direction */
+	gpio_direction_none(GPIO_PORT9CR);  /* FSIAOBT needs no direction */
+	gpio_direction_none(GPIO_PORT10CR); /* FSIAOLR needs no direction */
 
 	intc_set_priority(IRQ_FSI, 3); /* irq priority FSI(3) > SMSC911X(2) */
 
diff --git a/arch/arm/mach-shmobile/board-marzen.c b/arch/arm/mach-shmobile/board-marzen.c
index 14de3787caf..3a528cf4366 100644
--- a/arch/arm/mach-shmobile/board-marzen.c
+++ b/arch/arm/mach-shmobile/board-marzen.c
@@ -27,6 +27,8 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/dma-mapping.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
 #include <mach/hardware.h>
 #include <mach/r8a7779.h>
@@ -37,6 +39,12 @@
 #include <asm/hardware/gic.h>
 #include <asm/traps.h>
 
+/* Dummy supplies, where voltage doesn't matter */
+static struct regulator_consumer_supply dummy_supplies[] = {
+	REGULATOR_SUPPLY("vddvario", "smsc911x"),
+	REGULATOR_SUPPLY("vdd33a", "smsc911x"),
+};
+
 /* SMSC LAN89218 */
 static struct resource smsc911x_resources[] = {
 	[0] = {
@@ -73,6 +81,8 @@ static struct platform_device *marzen_devices[] __initdata = {
 
 static void __init marzen_init(void)
 {
+	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+
 	r8a7779_pinmux_init();
 
 	/* SCIF2 (CN18: DEBUG0) */