Merge tag 'imx-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes

From Shawn Guo:
The imx fixes for 3.9:
 - move early resume code out of .data section to fix allyesconfig
   failure since c08e20d (arm: Add v7_invalidate_l1 to cache-v7.S)
   gets merged
 - Fix incorrect DISP1_DAT_21 number in imx53-mba53 disp1-grp1

* tag 'imx-fixes-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: dts: imx53-mba53: fix fsl,pins for disp1-grp1
  ARM: mach-imx: move early resume code out of the .data section

Signed-off-by: Olof Johansson <olof@lixom.net>

3 files changed, 10 insertions, 26 deletions

diff --git a/arch/arm/boot/dts/imx53-mba53.dts b/arch/arm/boot/dts/imx53-mba53.dts
index e54fffd4836..468c0a1d48d 100644
--- a/arch/arm/boot/dts/imx53-mba53.dts
+++ b/arch/arm/boot/dts/imx53-mba53.dts
@@ -42,10 +42,9 @@
 			fsl,pins = <689 0x10000		/* DISP1_DRDY	*/
 				    482 0x10000		/* DISP1_HSYNC	*/
 				    489 0x10000		/* DISP1_VSYNC	*/
-				    684 0x10000		/* DISP1_DAT_0	*/
 				    515 0x10000		/* DISP1_DAT_22	*/
 				    523 0x10000		/* DISP1_DAT_23	*/
-				    543 0x10000		/* DISP1_DAT_21	*/
+				    545 0x10000		/* DISP1_DAT_21	*/
 				    553 0x10000		/* DISP1_DAT_20	*/
 				    558 0x10000		/* DISP1_DAT_19	*/
 				    564 0x10000		/* DISP1_DAT_18	*/
diff --git a/arch/arm/mach-imx/headsmp.S b/arch/arm/mach-imx/headsmp.S
index 921fc155585..a58c8b0527c 100644
--- a/arch/arm/mach-imx/headsmp.S
+++ b/arch/arm/mach-imx/headsmp.S
@@ -26,16 +26,16 @@ ENDPROC(v7_secondary_startup)
 
 #ifdef CONFIG_PM
 /*
- * The following code is located into the .data section.  This is to
- * allow phys_l2x0_saved_regs to be accessed with a relative load
- * as we are running on physical address here.
+ * The following code must assume it is running from physical address
+ * where absolute virtual addresses to the data section have to be
+ * turned into relative ones.
  */
-	.data
-	.align
 
 #ifdef CONFIG_CACHE_L2X0
 	.macro	pl310_resume
-	ldr	r2, phys_l2x0_saved_regs
+	adr	r0, l2x0_saved_regs_offset
+	ldr	r2, [r0]
+	add	r2, r2, r0
 	ldr	r0, [r2, #L2X0_R_PHY_BASE]	@ get physical base of l2x0
 	ldr	r1, [r2, #L2X0_R_AUX_CTRL]	@ get aux_ctrl value
 	str	r1, [r0, #L2X0_AUX_CTRL]	@ restore aux_ctrl
@@ -43,9 +43,9 @@ ENDPROC(v7_secondary_startup)
 	str	r1, [r0, #L2X0_CTRL]		@ re-enable L2
 	.endm
 
-	.globl	phys_l2x0_saved_regs
-phys_l2x0_saved_regs:
-        .long   0
+l2x0_saved_regs_offset:
+	.word	l2x0_saved_regs - .
+
 #else
 	.macro	pl310_resume
 	.endm
diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c
index ee42d20cba1..5faba7a3c95 100644
--- a/arch/arm/mach-imx/pm-imx6q.c
+++ b/arch/arm/mach-imx/pm-imx6q.c
@@ -22,8 +22,6 @@
 #include "common.h"
 #include "hardware.h"
 
-extern unsigned long phys_l2x0_saved_regs;
-
 static int imx6q_suspend_finish(unsigned long val)
 {
 	cpu_do_idle();
@@ -57,18 +55,5 @@ static const struct platform_suspend_ops imx6q_pm_ops = {
 
 void __init imx6q_pm_init(void)
 {
-	/*
-	 * The l2x0 core code provides an infrastucture to save and restore
-	 * l2x0 registers across suspend/resume cycle.  But because imx6q
-	 * retains L2 content during suspend and needs to resume L2 before
-	 * MMU is enabled, it can only utilize register saving support and
-	 * have to take care of restoring on its own.  So we save physical
-	 * address of the data structure used by l2x0 core to save registers,
-	 * and later restore the necessary ones in imx6q resume entry.
-	 */
-#ifdef CONFIG_CACHE_L2X0
-	phys_l2x0_saved_regs = __pa(&l2x0_saved_regs);
-#endif
-
 	suspend_set_ops(&imx6q_pm_ops);
 }