Merge git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (110 commits)
  sh: i2c-sh7760: Replase from ctrl_* to __raw_*
  sh: clkfwk: Shuffle around to match the intc split up.
  sh: clkfwk: modify for_each_frequency end condition
  sh: fix clk_get() error handling
  sh: clkfwk: Fix fault in frequency iterator.
  sh: clkfwk: Add a helper for rate rounding by divisor ranges.
  sh: clkfwk: Abstract rate rounding helper.
  sh: clkfwk: support clock remapping.
  sh: pci: Convert to upper/lower_32_bits() helpers.
  sh: mach-sdk7786: Add support for the FPGA SRAM.
  sh: Provide a generic SRAM pool for tiny memories.
  sh: pci: Support secondary FPGA-driven PCIe clocks on SDK7786.
  sh: pci: Support slot 4 routing on SDK7786.
  sh: Fix up PMB locking.
  sh: mach-sdk7786: Add support for fpga gpios.
  sh: use pr_fmt for clock framework, too.
  sh: remove name and id from struct clk
  sh: free-without-alloc fix for sh_mobile_lcdcfb
  sh: perf: Set up perf_max_events.
  sh: perf: Support SH-X3 hardware counters.
  ...

Fix up trivial conflicts (perf_max_events got removed) in arch/sh/kernel/perf_event.c

13 files changed, 978 insertions, 22 deletions

diff --git a/arch/sh/boards/Kconfig b/arch/sh/boards/Kconfig
index 07b35ca2f64..9c94711aa6c 100644
--- a/arch/sh/boards/Kconfig
+++ b/arch/sh/boards/Kconfig
@@ -155,6 +155,8 @@ config SH_SDK7786
 	depends on CPU_SUBTYPE_SH7786
 	select SYS_SUPPORTS_PCI
 	select NO_IOPORT if !PCI
+	select ARCH_WANT_OPTIONAL_GPIOLIB
+	select HAVE_SRAM_POOL
 	help
 	  Select SDK7786 if configuring for a Renesas Technology Europe
 	  SH7786-65nm board.
@@ -165,6 +167,11 @@ config SH_HIGHLANDER
 	select SYS_SUPPORTS_PCI
 	select IO_TRAPPED if MMU
 
+config SH_SH7757LCR
+	bool "SH7757LCR"
+	depends on CPU_SUBTYPE_SH7757
+	select ARCH_REQUIRE_GPIOLIB
+
 config SH_SH7785LCR
 	bool "SH7785LCR"
 	depends on CPU_SUBTYPE_SH7785
@@ -309,6 +316,17 @@ config SH_POLARIS
 	help
 	  Select if configuring for an SMSC Polaris development board
 
+config SH_SH2007
+	bool "SH-2007 board"
+	select NO_IOPORT
+	depends on CPU_SUBTYPE_SH7780
+	help
+	  SH-2007 is a single-board computer based around SH7780 chip
+	  intended for embedded applications.
+	  It has an Ethernet interface (SMC9118), direct connected
+	  Compact Flash socket, two serial ports and PC-104 bus.
+	  More information at <http://sh2000.sh-linux.org>.
+
 endmenu
 
 source "arch/sh/boards/mach-r2d/Kconfig"
diff --git a/arch/sh/boards/Makefile b/arch/sh/boards/Makefile
index 4f90f9b7a92..38ef655cc0f 100644
--- a/arch/sh/boards/Makefile
+++ b/arch/sh/boards/Makefile
@@ -2,6 +2,7 @@
 # Specific board support, not covered by a mach group.
 #
 obj-$(CONFIG_SH_MAGIC_PANEL_R2)	+= board-magicpanelr2.o
+obj-$(CONFIG_SH_SH2007)		+= board-sh2007.o
 obj-$(CONFIG_SH_SH7785LCR)	+= board-sh7785lcr.o
 obj-$(CONFIG_SH_URQUELL)	+= board-urquell.o
 obj-$(CONFIG_SH_SHMIN)		+= board-shmin.o
@@ -9,3 +10,4 @@ obj-$(CONFIG_SH_EDOSK7760)	+= board-edosk7760.o
 obj-$(CONFIG_SH_ESPT)		+= board-espt.o
 obj-$(CONFIG_SH_POLARIS)	+= board-polaris.o
 obj-$(CONFIG_SH_TITAN)		+= board-titan.o
+obj-$(CONFIG_SH_SH7757LCR)	+= board-sh7757lcr.o
diff --git a/arch/sh/boards/board-sh2007.c b/arch/sh/boards/board-sh2007.c
new file mode 100644
index 00000000000..b90b78f6a82
--- /dev/null
+++ b/arch/sh/boards/board-sh2007.c
@@ -0,0 +1,133 @@
+/*
+ * SH-2007 board support.
+ *
+ * Copyright (C) 2003, 2004  SUGIOKA Toshinobu
+ * Copyright (C) 2010  Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
+ */
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/smsc911x.h>
+#include <linux/platform_device.h>
+#include <linux/ata_platform.h>
+#include <linux/io.h>
+#include <asm/machvec.h>
+#include <mach/sh2007.h>
+
+struct smsc911x_platform_config smc911x_info = {
+	.flags		= SMSC911X_USE_32BIT,
+	.irq_polarity	= SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+	.irq_type	= SMSC911X_IRQ_TYPE_PUSH_PULL,
+};
+
+static struct resource smsc9118_0_resources[] = {
+	[0] = {
+		.start	= SMC0_BASE,
+		.end	= SMC0_BASE + 0xff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0x240),
+		.end	= evt2irq(0x240),
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct resource smsc9118_1_resources[] = {
+	[0] = {
+		.start	= SMC1_BASE,
+		.end	= SMC1_BASE + 0xff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0x280),
+		.end	= evt2irq(0x280),
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static struct platform_device smsc9118_0_device = {
+	.name		= "smsc911x",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(smsc9118_0_resources),
+	.resource	= smsc9118_0_resources,
+	.dev = {
+		.platform_data = &smc911x_info,
+	},
+};
+
+static struct platform_device smsc9118_1_device = {
+	.name		= "smsc911x",
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(smsc9118_1_resources),
+	.resource	= smsc9118_1_resources,
+	.dev = {
+		.platform_data = &smc911x_info,
+	},
+};
+
+static struct resource cf_resources[] = {
+	[0] = {
+		.start	= CF_BASE + CF_OFFSET,
+		.end	= CF_BASE + CF_OFFSET + 0x0f,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= CF_BASE + CF_OFFSET + 0x206,
+		.end	= CF_BASE + CF_OFFSET + 0x20f,
+		.flags	= IORESOURCE_MEM,
+	},
+	[2] = {
+		.start	= evt2irq(0x2c0),
+		.end	= evt2irq(0x2c0),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device cf_device  = {
+	.name		= "pata_platform",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(cf_resources),
+	.resource	= cf_resources,
+};
+
+static struct platform_device *sh2007_devices[] __initdata = {
+	&smsc9118_0_device,
+	&smsc9118_1_device,
+	&cf_device,
+};
+
+static int __init sh2007_io_init(void)
+{
+	platform_add_devices(sh2007_devices, ARRAY_SIZE(sh2007_devices));
+	return 0;
+}
+subsys_initcall(sh2007_io_init);
+
+static void __init sh2007_init_irq(void)
+{
+	plat_irq_setup_pins(IRQ_MODE_IRQ);
+}
+
+/*
+ * Initialize the board
+ */
+static void __init sh2007_setup(char **cmdline_p)
+{
+	printk(KERN_INFO "SH-2007 Setup...");
+
+	/* setup wait control registers for area 5 */
+	__raw_writel(CS5BCR_D, CS5BCR);
+	__raw_writel(CS5WCR_D, CS5WCR);
+	__raw_writel(CS5PCR_D, CS5PCR);
+
+	printk(KERN_INFO " done.\n");
+}
+
+/*
+ * The Machine Vector
+ */
+struct sh_machine_vector mv_sh2007 __initmv = {
+	.mv_setup		= sh2007_setup,
+	.mv_name		= "sh2007",
+	.mv_init_irq		= sh2007_init_irq,
+};
diff --git a/arch/sh/boards/board-sh7757lcr.c b/arch/sh/boards/board-sh7757lcr.c
new file mode 100644
index 00000000000..c475f1056ab
--- /dev/null
+++ b/arch/sh/boards/board-sh7757lcr.c
@@ -0,0 +1,374 @@
+/*
+ * Renesas R0P7757LC0012RL Support.
+ *
+ * Copyright (C) 2009 - 2010  Renesas Solutions Corp.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/flash.h>
+#include <linux/io.h>
+#include <cpu/sh7757.h>
+#include <asm/sh_eth.h>
+#include <asm/heartbeat.h>
+
+static struct resource heartbeat_resource = {
+	.start	= 0xffec005c,	/* PUDR */
+	.end	= 0xffec005c,
+	.flags	= IORESOURCE_MEM | IORESOURCE_MEM_8BIT,
+};
+
+static unsigned char heartbeat_bit_pos[] = { 0, 1, 2, 3 };
+
+static struct heartbeat_data heartbeat_data = {
+	.bit_pos	= heartbeat_bit_pos,
+	.nr_bits	= ARRAY_SIZE(heartbeat_bit_pos),
+	.flags		= HEARTBEAT_INVERTED,
+};
+
+static struct platform_device heartbeat_device = {
+	.name		= "heartbeat",
+	.id		= -1,
+	.dev	= {
+		.platform_data	= &heartbeat_data,
+	},
+	.num_resources	= 1,
+	.resource	= &heartbeat_resource,
+};
+
+/* Fast Ethernet */
+static struct resource sh_eth0_resources[] = {
+	{
+		.start  = 0xfef00000,
+		.end    = 0xfef001ff,
+		.flags  = IORESOURCE_MEM,
+	}, {
+		.start  = 84,
+		.end    = 84,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct sh_eth_plat_data sh7757_eth0_pdata = {
+	.phy = 1,
+	.edmac_endian = EDMAC_LITTLE_ENDIAN,
+};
+
+static struct platform_device sh7757_eth0_device = {
+	.name		= "sh-eth",
+	.resource	= sh_eth0_resources,
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(sh_eth0_resources),
+	.dev		= {
+		.platform_data = &sh7757_eth0_pdata,
+	},
+};
+
+static struct resource sh_eth1_resources[] = {
+	{
+		.start  = 0xfef00800,
+		.end    = 0xfef009ff,
+		.flags  = IORESOURCE_MEM,
+	}, {
+		.start  = 84,
+		.end    = 84,
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct sh_eth_plat_data sh7757_eth1_pdata = {
+	.phy = 1,
+	.edmac_endian = EDMAC_LITTLE_ENDIAN,
+};
+
+static struct platform_device sh7757_eth1_device = {
+	.name		= "sh-eth",
+	.resource	= sh_eth1_resources,
+	.id		= 1,
+	.num_resources	= ARRAY_SIZE(sh_eth1_resources),
+	.dev		= {
+		.platform_data = &sh7757_eth1_pdata,
+	},
+};
+
+static struct platform_device *sh7757lcr_devices[] __initdata = {
+	&heartbeat_device,
+	&sh7757_eth0_device,
+	&sh7757_eth1_device,
+};
+
+static int __init sh7757lcr_devices_setup(void)
+{
+	/* RGMII (PTA) */
+	gpio_request(GPIO_FN_ET0_MDC, NULL);
+	gpio_request(GPIO_FN_ET0_MDIO, NULL);
+	gpio_request(GPIO_FN_ET1_MDC, NULL);
+	gpio_request(GPIO_FN_ET1_MDIO, NULL);
+
+	/* ONFI (PTB, PTZ) */
+	gpio_request(GPIO_FN_ON_NRE, NULL);
+	gpio_request(GPIO_FN_ON_NWE, NULL);
+	gpio_request(GPIO_FN_ON_NWP, NULL);
+	gpio_request(GPIO_FN_ON_NCE0, NULL);
+	gpio_request(GPIO_FN_ON_R_B0, NULL);
+	gpio_request(GPIO_FN_ON_ALE, NULL);
+	gpio_request(GPIO_FN_ON_CLE, NULL);
+
+	gpio_request(GPIO_FN_ON_DQ7, NULL);
+	gpio_request(GPIO_FN_ON_DQ6, NULL);
+	gpio_request(GPIO_FN_ON_DQ5, NULL);
+	gpio_request(GPIO_FN_ON_DQ4, NULL);
+	gpio_request(GPIO_FN_ON_DQ3, NULL);
+	gpio_request(GPIO_FN_ON_DQ2, NULL);
+	gpio_request(GPIO_FN_ON_DQ1, NULL);
+	gpio_request(GPIO_FN_ON_DQ0, NULL);
+
+	/* IRQ8 to 0 (PTB, PTC) */
+	gpio_request(GPIO_FN_IRQ8, NULL);
+	gpio_request(GPIO_FN_IRQ7, NULL);
+	gpio_request(GPIO_FN_IRQ6, NULL);
+	gpio_request(GPIO_FN_IRQ5, NULL);
+	gpio_request(GPIO_FN_IRQ4, NULL);
+	gpio_request(GPIO_FN_IRQ3, NULL);
+	gpio_request(GPIO_FN_IRQ2, NULL);
+	gpio_request(GPIO_FN_IRQ1, NULL);
+	gpio_request(GPIO_FN_IRQ0, NULL);
+
+	/* SPI0 (PTD) */
+	gpio_request(GPIO_FN_SP0_MOSI, NULL);
+	gpio_request(GPIO_FN_SP0_MISO, NULL);
+	gpio_request(GPIO_FN_SP0_SCK, NULL);
+	gpio_request(GPIO_FN_SP0_SCK_FB, NULL);
+	gpio_request(GPIO_FN_SP0_SS0, NULL);
+	gpio_request(GPIO_FN_SP0_SS1, NULL);
+	gpio_request(GPIO_FN_SP0_SS2, NULL);
+	gpio_request(GPIO_FN_SP0_SS3, NULL);
+
+	/* RMII 0/1 (PTE, PTF) */
+	gpio_request(GPIO_FN_RMII0_CRS_DV, NULL);
+	gpio_request(GPIO_FN_RMII0_TXD1, NULL);
+	gpio_request(GPIO_FN_RMII0_TXD0, NULL);
+	gpio_request(GPIO_FN_RMII0_TXEN, NULL);
+	gpio_request(GPIO_FN_RMII0_REFCLK, NULL);
+	gpio_request(GPIO_FN_RMII0_RXD1, NULL);
+	gpio_request(GPIO_FN_RMII0_RXD0, NULL);
+	gpio_request(GPIO_FN_RMII0_RX_ER, NULL);
+	gpio_request(GPIO_FN_RMII1_CRS_DV, NULL);
+	gpio_request(GPIO_FN_RMII1_TXD1, NULL);
+	gpio_request(GPIO_FN_RMII1_TXD0, NULL);
+	gpio_request(GPIO_FN_RMII1_TXEN, NULL);
+	gpio_request(GPIO_FN_RMII1_REFCLK, NULL);
+	gpio_request(GPIO_FN_RMII1_RXD1, NULL);
+	gpio_request(GPIO_FN_RMII1_RXD0, NULL);
+	gpio_request(GPIO_FN_RMII1_RX_ER, NULL);
+
+	/* eMMC (PTG) */
+	gpio_request(GPIO_FN_MMCCLK, NULL);
+	gpio_request(GPIO_FN_MMCCMD, NULL);
+	gpio_request(GPIO_FN_MMCDAT7, NULL);
+	gpio_request(GPIO_FN_MMCDAT6, NULL);
+	gpio_request(GPIO_FN_MMCDAT5, NULL);
+	gpio_request(GPIO_FN_MMCDAT4, NULL);
+	gpio_request(GPIO_FN_MMCDAT3, NULL);
+	gpio_request(GPIO_FN_MMCDAT2, NULL);
+	gpio_request(GPIO_FN_MMCDAT1, NULL);
+	gpio_request(GPIO_FN_MMCDAT0, NULL);
+
+	/* LPC (PTG, PTH, PTQ, PTU) */
+	gpio_request(GPIO_FN_SERIRQ, NULL);
+	gpio_request(GPIO_FN_LPCPD, NULL);
+	gpio_request(GPIO_FN_LDRQ, NULL);
+	gpio_request(GPIO_FN_WP, NULL);
+	gpio_request(GPIO_FN_FMS0, NULL);
+	gpio_request(GPIO_FN_LAD3, NULL);
+	gpio_request(GPIO_FN_LAD2, NULL);
+	gpio_request(GPIO_FN_LAD1, NULL);
+	gpio_request(GPIO_FN_LAD0, NULL);
+	gpio_request(GPIO_FN_LFRAME, NULL);
+	gpio_request(GPIO_FN_LRESET, NULL);
+	gpio_request(GPIO_FN_LCLK, NULL);
+	gpio_request(GPIO_FN_LGPIO7, NULL);
+	gpio_request(GPIO_FN_LGPIO6, NULL);
+	gpio_request(GPIO_FN_LGPIO5, NULL);
+	gpio_request(GPIO_FN_LGPIO4, NULL);
+
+	/* SPI1 (PTH) */
+	gpio_request(GPIO_FN_SP1_MOSI, NULL);
+	gpio_request(GPIO_FN_SP1_MISO, NULL);
+	gpio_request(GPIO_FN_SP1_SCK, NULL);
+	gpio_request(GPIO_FN_SP1_SCK_FB, NULL);
+	gpio_request(GPIO_FN_SP1_SS0, NULL);
+	gpio_request(GPIO_FN_SP1_SS1, NULL);
+
+	/* SDHI (PTI) */
+	gpio_request(GPIO_FN_SD_WP, NULL);
+	gpio_request(GPIO_FN_SD_CD, NULL);
+	gpio_request(GPIO_FN_SD_CLK, NULL);
+	gpio_request(GPIO_FN_SD_CMD, NULL);
+	gpio_request(GPIO_FN_SD_D3, NULL);
+	gpio_request(GPIO_FN_SD_D2, NULL);
+	gpio_request(GPIO_FN_SD_D1, NULL);
+	gpio_request(GPIO_FN_SD_D0, NULL);
+
+	/* SCIF3/4 (PTJ, PTW) */
+	gpio_request(GPIO_FN_RTS3, NULL);
+	gpio_request(GPIO_FN_CTS3, NULL);
+	gpio_request(GPIO_FN_TXD3, NULL);
+	gpio_request(GPIO_FN_RXD3, NULL);
+	gpio_request(GPIO_FN_RTS4, NULL);
+	gpio_request(GPIO_FN_RXD4, NULL);
+	gpio_request(GPIO_FN_TXD4, NULL);
+	gpio_request(GPIO_FN_CTS4, NULL);
+
+	/* SERMUX (PTK, PTL, PTO, PTV) */
+	gpio_request(GPIO_FN_COM2_TXD, NULL);
+	gpio_request(GPIO_FN_COM2_RXD, NULL);
+	gpio_request(GPIO_FN_COM2_RTS, NULL);
+	gpio_request(GPIO_FN_COM2_CTS, NULL);
+	gpio_request(GPIO_FN_COM2_DTR, NULL);
+	gpio_request(GPIO_FN_COM2_DSR, NULL);
+	gpio_request(GPIO_FN_COM2_DCD, NULL);
+	gpio_request(GPIO_FN_COM2_RI, NULL);
+	gpio_request(GPIO_FN_RAC_RXD, NULL);
+	gpio_request(GPIO_FN_RAC_RTS, NULL);
+	gpio_request(GPIO_FN_RAC_CTS, NULL);
+	gpio_request(GPIO_FN_RAC_DTR, NULL);
+	gpio_request(GPIO_FN_RAC_DSR, NULL);
+	gpio_request(GPIO_FN_RAC_DCD, NULL);
+	gpio_request(GPIO_FN_RAC_TXD, NULL);
+	gpio_request(GPIO_FN_COM1_TXD, NULL);
+	gpio_request(GPIO_FN_COM1_RXD, NULL);
+	gpio_request(GPIO_FN_COM1_RTS, NULL);
+	gpio_request(GPIO_FN_COM1_CTS, NULL);
+
+	writeb(0x10, 0xfe470000);	/* SMR0: SerMux mode 0 */
+
+	/* IIC (PTM, PTR, PTS) */
+	gpio_request(GPIO_FN_SDA7, NULL);
+	gpio_request(GPIO_FN_SCL7, NULL);
+	gpio_request(GPIO_FN_SDA6, NULL);
+	gpio_request(GPIO_FN_SCL6, NULL);
+	gpio_request(GPIO_FN_SDA5, NULL);
+	gpio_request(GPIO_FN_SCL5, NULL);
+	gpio_request(GPIO_FN_SDA4, NULL);
+	gpio_request(GPIO_FN_SCL4, NULL);
+	gpio_request(GPIO_FN_SDA3, NULL);
+	gpio_request(GPIO_FN_SCL3, NULL);
+	gpio_request(GPIO_FN_SDA2, NULL);
+	gpio_request(GPIO_FN_SCL2, NULL);
+	gpio_request(GPIO_FN_SDA1, NULL);
+	gpio_request(GPIO_FN_SCL1, NULL);
+	gpio_request(GPIO_FN_SDA0, NULL);
+	gpio_request(GPIO_FN_SCL0, NULL);
+
+	/* USB (PTN) */
+	gpio_request(GPIO_FN_VBUS_EN, NULL);
+	gpio_request(GPIO_FN_VBUS_OC, NULL);
+
+	/* SGPIO1/0 (PTN, PTO) */
+	gpio_request(GPIO_FN_SGPIO1_CLK, NULL);
+	gpio_request(GPIO_FN_SGPIO1_LOAD, NULL);
+	gpio_request(GPIO_FN_SGPIO1_DI, NULL);
+	gpio_request(GPIO_FN_SGPIO1_DO, NULL);
+	gpio_request(GPIO_FN_SGPIO0_CLK, NULL);
+	gpio_request(GPIO_FN_SGPIO0_LOAD, NULL);
+	gpio_request(GPIO_FN_SGPIO0_DI, NULL);
+	gpio_request(GPIO_FN_SGPIO0_DO, NULL);
+
+	/* WDT (PTN) */
+	gpio_request(GPIO_FN_SUB_CLKIN, NULL);
+
+	/* System (PTT) */
+	gpio_request(GPIO_FN_STATUS1, NULL);
+	gpio_request(GPIO_FN_STATUS0, NULL);
+
+	/* PWMX (PTT) */
+	gpio_request(GPIO_FN_PWMX1, NULL);
+	gpio_request(GPIO_FN_PWMX0, NULL);
+
+	/* R-SPI (PTV) */
+	gpio_request(GPIO_FN_R_SPI_MOSI, NULL);
+	gpio_request(GPIO_FN_R_SPI_MISO, NULL);
+	gpio_request(GPIO_FN_R_SPI_RSPCK, NULL);
+	gpio_request(GPIO_FN_R_SPI_SSL0, NULL);
+	gpio_request(GPIO_FN_R_SPI_SSL1, NULL);
+
+	/* EVC (PTV, PTW) */
+	gpio_request(GPIO_FN_EVENT7, NULL);
+	gpio_request(GPIO_FN_EVENT6, NULL);
+	gpio_request(GPIO_FN_EVENT5, NULL);
+	gpio_request(GPIO_FN_EVENT4, NULL);
+	gpio_request(GPIO_FN_EVENT3, NULL);
+	gpio_request(GPIO_FN_EVENT2, NULL);
+	gpio_request(GPIO_FN_EVENT1, NULL);
+	gpio_request(GPIO_FN_EVENT0, NULL);
+
+	/* LED for heartbeat */
+	gpio_request(GPIO_PTU3, NULL);
+	gpio_direction_output(GPIO_PTU3, 1);
+	gpio_request(GPIO_PTU2, NULL);
+	gpio_direction_output(GPIO_PTU2, 1);
+	gpio_request(GPIO_PTU1, NULL);
+	gpio_direction_output(GPIO_PTU1, 1);
+	gpio_request(GPIO_PTU0, NULL);
+	gpio_direction_output(GPIO_PTU0, 1);
+
+	/* control for MDIO of Gigabit Ethernet */
+	gpio_request(GPIO_PTT4, NULL);
+	gpio_direction_output(GPIO_PTT4, 1);
+
+	/* control for eMMC */
+	gpio_request(GPIO_PTT7, NULL);		/* eMMC_RST# */
+	gpio_direction_output(GPIO_PTT7, 0);
+	gpio_request(GPIO_PTT6, NULL);		/* eMMC_INDEX# */
+	gpio_direction_output(GPIO_PTT6, 0);
+	gpio_request(GPIO_PTT5, NULL);		/* eMMC_PRST# */
+	gpio_direction_output(GPIO_PTT5, 1);
+
+	/* General platform */
+	return platform_add_devices(sh7757lcr_devices,
+				    ARRAY_SIZE(sh7757lcr_devices));
+}
+arch_initcall(sh7757lcr_devices_setup);
+
+/* Initialize IRQ setting */
+void __init init_sh7757lcr_IRQ(void)
+{
+	plat_irq_setup_pins(IRQ_MODE_IRQ7654);
+	plat_irq_setup_pins(IRQ_MODE_IRQ3210);
+}
+
+/* Initialize the board */
+static void __init sh7757lcr_setup(char **cmdline_p)
+{
+	printk(KERN_INFO "Renesas R0P7757LC0012RL support.\n");
+}
+
+static int sh7757lcr_mode_pins(void)
+{
+	int value = 0;
+
+	/* These are the factory default settings of S3 (Low active).
+	 * If you change these dip switches then you will need to
+	 * adjust the values below as well.
+	 */
+	value |= MODE_PIN0;	/* Clock Mode: 1 */
+
+	return value;
+}
+
+/* The Machine Vector */
+static struct sh_machine_vector mv_sh7757lcr __initmv = {
+	.mv_name		= "SH7757LCR",
+	.mv_setup		= sh7757lcr_setup,
+	.mv_init_irq		= init_sh7757lcr_IRQ,
+	.mv_mode_pins		= sh7757lcr_mode_pins,
+};
+
diff --git a/arch/sh/boards/mach-ecovec24/setup.c b/arch/sh/boards/mach-ecovec24/setup.c
index 1d7b495a7db..71a3368ab1f 100644
--- a/arch/sh/boards/mach-ecovec24/setup.c
+++ b/arch/sh/boards/mach-ecovec24/setup.c
@@ -1248,14 +1248,14 @@ static int __init arch_setup(void)
 
 	/* set SPU2 clock to 83.4 MHz */
 	clk = clk_get(NULL, "spu_clk");
-	if (clk) {
+	if (!IS_ERR(clk)) {
 		clk_set_rate(clk, clk_round_rate(clk, 83333333));
 		clk_put(clk);
 	}
 
 	/* change parent of FSI B */
 	clk = clk_get(NULL, "fsib_clk");
-	if (clk) {
+	if (!IS_ERR(clk)) {
 		clk_register(&fsimckb_clk);
 		clk_set_parent(clk, &fsimckb_clk);
 		clk_set_rate(clk, 11000);
@@ -1273,7 +1273,7 @@ static int __init arch_setup(void)
 
 	/* set VPU clock to 166 MHz */
 	clk = clk_get(NULL, "vpu_clk");
-	if (clk) {
+	if (!IS_ERR(clk)) {
 		clk_set_rate(clk, clk_round_rate(clk, 166000000));
 		clk_put(clk);
 	}
diff --git a/arch/sh/boards/mach-sdk7786/Makefile b/arch/sh/boards/mach-sdk7786/Makefile
index a29f19e85b6..23ff7d4ac49 100644
--- a/arch/sh/boards/mach-sdk7786/Makefile
+++ b/arch/sh/boards/mach-sdk7786/Makefile
@@ -1 +1,4 @@
-obj-y	:= setup.o fpga.o irq.o
+obj-y	:= fpga.o irq.o setup.o
+
+obj-$(CONFIG_GENERIC_GPIO)	+= gpio.o
+obj-$(CONFIG_HAVE_SRAM_POOL)	+= sram.o
diff --git a/arch/sh/boards/mach-sdk7786/gpio.c b/arch/sh/boards/mach-sdk7786/gpio.c
new file mode 100644
index 00000000000..f71ce09d4e1
--- /dev/null
+++ b/arch/sh/boards/mach-sdk7786/gpio.c
@@ -0,0 +1,49 @@
+/*
+ * SDK7786 FPGA USRGPIR Support.
+ *
+ * Copyright (C) 2010  Paul Mundt
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <mach/fpga.h>
+
+#define NR_FPGA_GPIOS	8
+
+static const char *usrgpir_gpio_names[NR_FPGA_GPIOS] = {
+	"in0", "in1", "in2", "in3", "in4", "in5", "in6", "in7",
+};
+
+static int usrgpir_gpio_direction_input(struct gpio_chip *chip, unsigned gpio)
+{
+	/* always in */
+	return 0;
+}
+
+static int usrgpir_gpio_get(struct gpio_chip *chip, unsigned gpio)
+{
+	return !!(fpga_read_reg(USRGPIR) & (1 << gpio));
+}
+
+static struct gpio_chip usrgpir_gpio_chip = {
+	.label			= "sdk7786-fpga",
+	.names			= usrgpir_gpio_names,
+	.direction_input	= usrgpir_gpio_direction_input,
+	.get			= usrgpir_gpio_get,
+	.base			= -1, /* don't care */
+	.ngpio			= NR_FPGA_GPIOS,
+};
+
+static int __init usrgpir_gpio_setup(void)
+{
+	return gpiochip_add(&usrgpir_gpio_chip);
+}
+device_initcall(usrgpir_gpio_setup);
diff --git a/arch/sh/boards/mach-sdk7786/setup.c b/arch/sh/boards/mach-sdk7786/setup.c
index 2ec1ea5cf8e..7e0c4e3878e 100644
--- a/arch/sh/boards/mach-sdk7786/setup.c
+++ b/arch/sh/boards/mach-sdk7786/setup.c
@@ -20,6 +20,8 @@
 #include <asm/machvec.h>
 #include <asm/heartbeat.h>
 #include <asm/sizes.h>
+#include <asm/clock.h>
+#include <asm/clkdev.h>
 #include <asm/reboot.h>
 #include <asm/smp-ops.h>
 
@@ -140,6 +142,45 @@ static int sdk7786_mode_pins(void)
 	return fpga_read_reg(MODSWR);
 }
 
+/*
+ * FPGA-driven PCIe clocks
+ *
+ * Historically these include the oscillator, clock B (slots 2/3/4) and
+ * clock A (slot 1 and the CPU clock). Newer revs of the PCB shove
+ * everything under a single PCIe clocks enable bit that happens to map
+ * to the same bit position as the oscillator bit for earlier FPGA
+ * versions.
+ *
+ * Given that the legacy clocks have the side-effect of shutting the CPU
+ * off through the FPGA along with the PCI slots, we simply leave them in
+ * their initial state and don't bother registering them with the clock
+ * framework.
+ */
+static int sdk7786_pcie_clk_enable(struct clk *clk)
+{
+	fpga_write_reg(fpga_read_reg(PCIECR) | PCIECR_CLKEN, PCIECR);
+	return 0;
+}
+
+static void sdk7786_pcie_clk_disable(struct clk *clk)
+{
+	fpga_write_reg(fpga_read_reg(PCIECR) & ~PCIECR_CLKEN, PCIECR);
+}
+
+static struct clk_ops sdk7786_pcie_clk_ops = {
+	.enable		= sdk7786_pcie_clk_enable,
+	.disable	= sdk7786_pcie_clk_disable,
+};
+
+static struct clk sdk7786_pcie_clk = {
+	.ops		= &sdk7786_pcie_clk_ops,
+};
+
+static struct clk_lookup sdk7786_pcie_cl = {
+	.con_id		= "pcie_plat_clk",
+	.clk		= &sdk7786_pcie_clk,
+};
+
 static int sdk7786_clk_init(void)
 {
 	struct clk *clk;
@@ -158,7 +199,18 @@ static int sdk7786_clk_init(void)
 	ret = clk_set_rate(clk, 33333333);
 	clk_put(clk);
 
-	return ret;
+	/*
+	 * Setup the FPGA clocks.
+	 */
+	ret = clk_register(&sdk7786_pcie_clk);
+	if (unlikely(ret)) {
+		pr_err("FPGA clock registration failed\n");
+		return ret;
+	}
+
+	clkdev_add(&sdk7786_pcie_cl);
+
+	return 0;
 }
 
 static void sdk7786_restart(char *cmd)
diff --git a/arch/sh/boards/mach-sdk7786/sram.c b/arch/sh/boards/mach-sdk7786/sram.c
new file mode 100644
index 00000000000..c81c3abbe01
--- /dev/null
+++ b/arch/sh/boards/mach-sdk7786/sram.c
@@ -0,0 +1,72 @@
+/*
+ * SDK7786 FPGA SRAM Support.
+ *
+ * Copyright (C) 2010  Paul Mundt
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/io.h>
+#include <linux/string.h>
+#include <mach/fpga.h>
+#include <asm/sram.h>
+#include <asm/sizes.h>
+
+static int __init fpga_sram_init(void)
+{
+	unsigned long phys;
+	unsigned int area;
+	void __iomem *vaddr;
+	int ret;
+	u16 data;
+
+	/* Enable FPGA SRAM */
+	data = fpga_read_reg(LCLASR);
+	data |= LCLASR_FRAMEN;
+	fpga_write_reg(data, LCLASR);
+
+	/*
+	 * FPGA_SEL determines the area mapping
+	 */
+	area = (data & LCLASR_FPGA_SEL_MASK) >> LCLASR_FPGA_SEL_SHIFT;
+	if (unlikely(area == LCLASR_AREA_MASK)) {
+		pr_err("FPGA memory unmapped.\n");
+		return -ENXIO;
+	}
+
+	/*
+	 * The memory itself occupies a 2KiB range at the top of the area
+	 * immediately below the system registers.
+	 */
+	phys = (area << 26) + SZ_64M - SZ_4K;
+
+	/*
+	 * The FPGA SRAM resides in translatable physical space, so set
+	 * up a mapping prior to inserting it in to the pool.
+	 */
+	vaddr = ioremap(phys, SZ_2K);
+	if (unlikely(!vaddr)) {
+		pr_err("Failed remapping FPGA memory.\n");
+		return -ENXIO;
+	}
+
+	pr_info("Adding %dKiB of FPGA memory at 0x%08lx-0x%08lx "
+		"(area %d) to pool.\n",
+		SZ_2K >> 10, phys, phys + SZ_2K - 1, area);
+
+	ret = gen_pool_add(sram_pool, (unsigned long)vaddr, SZ_2K, -1);
+	if (unlikely(ret < 0)) {
+		pr_err("Failed adding memory\n");
+		iounmap(vaddr);
+		return ret;
+	}
+
+	return 0;
+}
+postcore_initcall(fpga_sram_init);
diff --git a/arch/sh/boards/mach-x3proto/Makefile b/arch/sh/boards/mach-x3proto/Makefile
index 983e4551fec..708c21c919f 100644
--- a/arch/sh/boards/mach-x3proto/Makefile
+++ b/arch/sh/boards/mach-x3proto/Makefile
@@ -1 +1,3 @@
 obj-y += setup.o ilsel.o
+
+obj-$(CONFIG_GENERIC_GPIO)	+= gpio.o
diff --git a/arch/sh/boards/mach-x3proto/gpio.c b/arch/sh/boards/mach-x3proto/gpio.c
new file mode 100644
index 00000000000..594adf76e46
--- /dev/null
+++ b/arch/sh/boards/mach-x3proto/gpio.c
@@ -0,0 +1,135 @@
+/*
+ * arch/sh/boards/mach-x3proto/gpio.c
+ *
+ * Renesas SH-X3 Prototype Baseboard GPIO Support.
+ *
+ * Copyright (C) 2010  Paul Mundt
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/spinlock.h>
+#include <linux/io.h>
+#include <mach/ilsel.h>
+#include <mach/hardware.h>
+
+#define KEYCTLR	0xb81c0000
+#define KEYOUTR	0xb81c0002
+#define KEYDETR 0xb81c0004
+
+static DEFINE_SPINLOCK(x3proto_gpio_lock);
+static unsigned int x3proto_gpio_irq_map[NR_BASEBOARD_GPIOS] = { 0, };
+
+static int x3proto_gpio_direction_input(struct gpio_chip *chip, unsigned gpio)
+{
+	unsigned long flags;
+	unsigned int data;
+
+	spin_lock_irqsave(&x3proto_gpio_lock, flags);
+	data = __raw_readw(KEYCTLR);
+	data |= (1 << gpio);
+	__raw_writew(data, KEYCTLR);
+	spin_unlock_irqrestore(&x3proto_gpio_lock, flags);
+
+	return 0;
+}
+
+static int x3proto_gpio_get(struct gpio_chip *chip, unsigned gpio)
+{
+	return !!(__raw_readw(KEYDETR) & (1 << gpio));
+}
+
+static int x3proto_gpio_to_irq(struct gpio_chip *chip, unsigned gpio)
+{
+	return x3proto_gpio_irq_map[gpio];
+}
+
+static void x3proto_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
+{
+	struct irq_chip *chip = get_irq_desc_chip(desc);
+	unsigned long mask;
+	int pin;
+
+	chip->mask_ack(irq);
+
+	mask = __raw_readw(KEYDETR);
+
+	for_each_set_bit(pin, &mask, NR_BASEBOARD_GPIOS)
+		generic_handle_irq(x3proto_gpio_to_irq(NULL, pin));
+
+	chip->unmask(irq);
+}
+
+struct gpio_chip x3proto_gpio_chip = {
+	.label			= "x3proto-gpio",
+	.direction_input	= x3proto_gpio_direction_input,
+	.get			= x3proto_gpio_get,
+	.to_irq			= x3proto_gpio_to_irq,
+	.base			= -1,
+	.ngpio			= NR_BASEBOARD_GPIOS,
+};
+
+int __init x3proto_gpio_setup(void)
+{
+	int ilsel;
+	int ret, i;
+
+	ilsel = ilsel_enable(ILSEL_KEY);
+	if (unlikely(ilsel < 0))
+		return ilsel;
+
+	ret = gpiochip_add(&x3proto_gpio_chip);
+	if (unlikely(ret))
+		goto err_gpio;
+
+	for (i = 0; i < NR_BASEBOARD_GPIOS; i++) {
+		unsigned long flags;
+		int irq = create_irq();
+
+		if (unlikely(irq < 0)) {
+			ret = -EINVAL;
+			goto err_irq;
+		}
+
+		spin_lock_irqsave(&x3proto_gpio_lock, flags);
+		x3proto_gpio_irq_map[i] = irq;
+		set_irq_chip_and_handler_name(irq, &dummy_irq_chip,
+					handle_simple_irq, "gpio");
+		spin_unlock_irqrestore(&x3proto_gpio_lock, flags);
+	}
+
+	pr_info("registering '%s' support, handling GPIOs %u -> %u, "
+		"bound to IRQ %u\n",
+		x3proto_gpio_chip.label, x3proto_gpio_chip.base,
+		x3proto_gpio_chip.base + x3proto_gpio_chip.ngpio,
+		ilsel);
+
+	set_irq_chained_handler(ilsel, x3proto_gpio_irq_handler);
+	set_irq_wake(ilsel, 1);
+
+	return 0;
+
+err_irq:
+	for (; i >= 0; --i)
+		if (x3proto_gpio_irq_map[i])
+			destroy_irq(x3proto_gpio_irq_map[i]);
+
+	ret = gpiochip_remove(&x3proto_gpio_chip);
+	if (unlikely(ret))
+		pr_err("Failed deregistering GPIO\n");
+
+err_gpio:
+	synchronize_irq(ilsel);
+
+	ilsel_disable(ILSEL_KEY);
+
+	return ret;
+}
diff --git a/arch/sh/boards/mach-x3proto/ilsel.c b/arch/sh/boards/mach-x3proto/ilsel.c
index 5c9842704c6..95e34613951 100644
--- a/arch/sh/boards/mach-x3proto/ilsel.c
+++ b/arch/sh/boards/mach-x3proto/ilsel.c
@@ -1,20 +1,22 @@
 /*
- * arch/sh/boards/renesas/x3proto/ilsel.c
+ * arch/sh/boards/mach-x3proto/ilsel.c
  *
  * Helper routines for SH-X3 proto board ILSEL.
  *
- * Copyright (C) 2007 Paul Mundt
+ * Copyright (C) 2007 - 2010  Paul Mundt
  *
  * This file is subject to the terms and conditions of the GNU General Public
  * License.  See the file "COPYING" in the main directory of this archive
  * for more details.
  */
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/bitmap.h>
 #include <linux/io.h>
-#include <asm/ilsel.h>
+#include <mach/ilsel.h>
 
 /*
  * ILSEL is split across:
@@ -64,6 +66,8 @@ static void __ilsel_enable(ilsel_source_t set, unsigned int bit)
 	unsigned int tmp, shift;
 	unsigned long addr;
 
+	pr_notice("enabling ILSEL set %d\n", set);
+
 	addr = mk_ilsel_addr(bit);
 	shift = mk_ilsel_shift(bit);
 
@@ -92,8 +96,10 @@ int ilsel_enable(ilsel_source_t set)
 {
 	unsigned int bit;
 
-	/* Aliased sources must use ilsel_enable_fixed() */
-	BUG_ON(set > ILSEL_KEY);
+	if (unlikely(set > ILSEL_KEY)) {
+		pr_err("Aliased sources must use ilsel_enable_fixed()\n");
+		return -EINVAL;
+	}
 
 	do {
 		bit = find_first_zero_bit(&ilsel_level_map, ILSEL_LEVELS);
@@ -140,6 +146,8 @@ void ilsel_disable(unsigned int irq)
 	unsigned long addr;
 	unsigned int tmp;
 
+	pr_notice("disabling ILSEL set %d\n", irq);
+
 	addr = mk_ilsel_addr(irq);
 
 	tmp = __raw_readw(addr);
diff --git a/arch/sh/boards/mach-x3proto/setup.c b/arch/sh/boards/mach-x3proto/setup.c
index 102bf56befb..d682e2b6a85 100644
--- a/arch/sh/boards/mach-x3proto/setup.c
+++ b/arch/sh/boards/mach-x3proto/setup.c
@@ -1,9 +1,9 @@
 /*
- * arch/sh/boards/renesas/x3proto/setup.c
+ * arch/sh/boards/mach-x3proto/setup.c
  *
  * Renesas SH-X3 Prototype Board Support.
  *
- * Copyright (C) 2007 - 2008 Paul Mundt
+ * Copyright (C) 2007 - 2010  Paul Mundt
  *
  * This file is subject to the terms and conditions of the GNU General Public
  * License.  See the file "COPYING" in the main directory of this archive
@@ -16,9 +16,13 @@
 #include <linux/smc91x.h>
 #include <linux/irq.h>
 #include <linux/interrupt.h>
+#include <linux/input.h>
 #include <linux/usb/r8a66597.h>
 #include <linux/usb/m66592.h>
-#include <asm/ilsel.h>
+#include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <mach/ilsel.h>
+#include <mach/hardware.h>
 #include <asm/smp-ops.h>
 
 static struct resource heartbeat_resources[] = {
@@ -122,15 +126,128 @@ static struct platform_device m66592_usb_peripheral_device = {
 	.resource	= m66592_usb_peripheral_resources,
 };
 
+static struct gpio_keys_button baseboard_buttons[NR_BASEBOARD_GPIOS] = {
+	{
+		.desc		= "key44",
+		.code		= KEY_POWER,
+		.active_low	= 1,
+		.wakeup		= 1,
+	}, {
+		.desc		= "key43",
+		.code		= KEY_SUSPEND,
+		.active_low	= 1,
+		.wakeup		= 1,
+	}, {
+		.desc		= "key42",
+		.code		= KEY_KATAKANAHIRAGANA,
+		.active_low	= 1,
+	}, {
+		.desc		= "key41",
+		.code		= KEY_SWITCHVIDEOMODE,
+		.active_low	= 1,
+	}, {
+		.desc		= "key34",
+		.code		= KEY_F12,
+		.active_low	= 1,
+	}, {
+		.desc		= "key33",
+		.code		= KEY_F11,
+		.active_low	= 1,
+	}, {
+		.desc		= "key32",
+		.code		= KEY_F10,
+		.active_low	= 1,
+	}, {
+		.desc		= "key31",
+		.code		= KEY_F9,
+		.active_low	= 1,
+	}, {
+		.desc		= "key24",
+		.code		= KEY_F8,
+		.active_low	= 1,
+	}, {
+		.desc		= "key23",
+		.code		= KEY_F7,
+		.active_low	= 1,
+	}, {
+		.desc		= "key22",
+		.code		= KEY_F6,
+		.active_low	= 1,
+	}, {
+		.desc		= "key21",
+		.code		= KEY_F5,
+		.active_low	= 1,
+	}, {
+		.desc		= "key14",
+		.code		= KEY_F4,
+		.active_low	= 1,
+	}, {
+		.desc		= "key13",
+		.code		= KEY_F3,
+		.active_low	= 1,
+	}, {
+		.desc		= "key12",
+		.code		= KEY_F2,
+		.active_low	= 1,
+	}, {
+		.desc		= "key11",
+		.code		= KEY_F1,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_platform_data baseboard_buttons_data = {
+	.buttons	= baseboard_buttons,
+	.nbuttons	= ARRAY_SIZE(baseboard_buttons),
+};
+
+static struct platform_device baseboard_buttons_device = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &baseboard_buttons_data,
+	},
+};
+
 static struct platform_device *x3proto_devices[] __initdata = {
 	&heartbeat_device,
 	&smc91x_device,
 	&r8a66597_usb_host_device,
 	&m66592_usb_peripheral_device,
+	&baseboard_buttons_device,
 };
 
+static void __init x3proto_init_irq(void)
+{
+	plat_irq_setup_pins(IRQ_MODE_IRL3210);
+
+	/* Set ICR0.LVLMODE */
+	__raw_writel(__raw_readl(0xfe410000) | (1 << 21), 0xfe410000);
+}
+
 static int __init x3proto_devices_setup(void)
 {
+	int ret, i;
+
+	/*
+	 * IRLs are only needed for ILSEL mappings, so flip over the INTC
+	 * pins at a later point to enable the GPIOs to settle.
+	 */
+	x3proto_init_irq();
+
+	/*
+	 * Now that ILSELs are available, set up the baseboard GPIOs.
+	 */
+	ret = x3proto_gpio_setup();
+	if (unlikely(ret))
+		return ret;
+
+	/*
+	 * Propagate dynamic GPIOs for the baseboard button device.
+	 */
+	for (i = 0; i < ARRAY_SIZE(baseboard_buttons); i++)
+		baseboard_buttons[i].gpio = x3proto_gpio_chip.base + i;
+
 	r8a66597_usb_host_resources[1].start =
 		r8a66597_usb_host_resources[1].end = ilsel_enable(ILSEL_USBH_I);
 
@@ -145,14 +262,6 @@ static int __init x3proto_devices_setup(void)
 }
 device_initcall(x3proto_devices_setup);
 
-static void __init x3proto_init_irq(void)
-{
-	plat_irq_setup_pins(IRQ_MODE_IRL3210);
-
-	/* Set ICR0.LVLMODE */
-	__raw_writel(__raw_readl(0xfe410000) | (1 << 21), 0xfe410000);
-}
-
 static void __init x3proto_setup(char **cmdline_p)
 {
 	register_smp_ops(&shx3_smp_ops);
@@ -161,5 +270,4 @@ static void __init x3proto_setup(char **cmdline_p)
 static struct sh_machine_vector mv_x3proto __initmv = {
 	.mv_name		= "x3proto",
 	.mv_setup		= x3proto_setup,
-	.mv_init_irq		= x3proto_init_irq,
 };