[PATCH] ppc32: katana updates

Update the katana platform support code:
- if booted as zImage, pass mem size in via bi_req from bootwrapper
- if booted as uImage, get mem size from bd_info passed in from u-boot
- add support for 82544 present on katana 752i's
- set cacheline size on pci devices
- some minor fixups

Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

2 files changed, 201 insertions, 68 deletions

diff --git a/arch/ppc/platforms/katana.c b/arch/ppc/platforms/katana.c
index 169dbf6534b..2b53afae0e9 100644
--- a/arch/ppc/platforms/katana.c
+++ b/arch/ppc/platforms/katana.c
@@ -33,6 +33,7 @@
 #include <linux/bootimg.h>
 #endif
 #include <asm/io.h>
+#include <asm/unistd.h>
 #include <asm/page.h>
 #include <asm/time.h>
 #include <asm/smp.h>
@@ -42,15 +43,14 @@
 #include <asm/mv64x60.h>
 #include <platforms/katana.h>
 
-static struct		mv64x60_handle bh;
-static katana_id_t	katana_id;
-static void __iomem	*cpld_base;
-static void __iomem	*sram_base;
-
-static u32		katana_flash_size_0;
-static u32		katana_flash_size_1;
-
-static u32		katana_bus_frequency;
+static struct mv64x60_handle	bh;
+static katana_id_t		katana_id;
+static void __iomem		*cpld_base;
+static void __iomem		*sram_base;
+static u32			katana_flash_size_0;
+static u32			katana_flash_size_1;
+static u32			katana_bus_frequency;
+static struct pci_controller	katana_hose_a;
 
 unsigned char	__res[sizeof(bd_t)];
 
@@ -71,8 +71,12 @@ katana_irq_lookup_750i(unsigned char idsel, unsigned char pin)
 			KATANA_PCI_INTA_IRQ_750i, KATANA_PCI_INTB_IRQ_750i },
 		/* IDSEL 6 (T8110) */
 		{KATANA_PCI_INTD_IRQ_750i, 0, 0, 0 },
+		/* IDSEL 7 (unused) */
+		{0, 0, 0, 0 },
+		/* IDSEL 8 (Intel 82544) (752i only but doesn't harm 750i) */
+		{KATANA_PCI_INTD_IRQ_750i, 0, 0, 0 },
 	};
-	const long min_idsel = 4, max_idsel = 6, irqs_per_slot = 4;
+	const long min_idsel = 4, max_idsel = 8, irqs_per_slot = 4;
 
 	return PCI_IRQ_TABLE_LOOKUP;
 }
@@ -148,7 +152,7 @@ katana_get_proc_num(void)
 			save_exclude = mv64x60_pci_exclude_bridge;
 			mv64x60_pci_exclude_bridge = 0;
 
-			early_read_config_word(bh.hose_a, 0,
+			early_read_config_word(bh.hose_b, 0,
 				PCI_DEVFN(0,0), PCI_DEVICE_ID, &val);
 
 			mv64x60_pci_exclude_bridge = save_exclude;
@@ -191,7 +195,8 @@ katana_setup_bridge(void)
 	struct mv64x60_setup_info si;
 	void __iomem *vaddr;
 	int i;
-	u16 val;
+	u32 v;
+	u16 val, type;
 	u8 save_exclude;
 
 	/*
@@ -222,6 +227,20 @@ katana_setup_bridge(void)
 			PCI_DEVICE_ID, val);
 	}
 
+	/*
+	 * While we're in here, set the hotswap register correctly.
+	 * Turn off blue LED; mask ENUM#, clear insertion & extraction bits.
+	 */
+	early_read_config_dword(&hose, 0, PCI_DEVFN(0, 0),
+		MV64360_PCICFG_CPCI_HOTSWAP, &v);
+	v &= ~(1<<19);
+	v |= ((1<<17) | (1<<22) | (1<<23));
+	early_write_config_dword(&hose, 0, PCI_DEVFN(0, 0),
+		MV64360_PCICFG_CPCI_HOTSWAP, v);
+
+	/* While we're at it, grab the bridge type for later */
+	early_read_config_word(&hose, 0, PCI_DEVFN(0, 0), PCI_DEVICE_ID, &type);
+
 	mv64x60_pci_exclude_bridge = save_exclude;
 	iounmap(vaddr);
 
@@ -251,21 +270,23 @@ katana_setup_bridge(void)
 		si.idma_options[i] = MV64360_IDMA2MEM_SNOOP_NONE;
 
 		si.pci_1.acc_cntl_options[i] =
-		    MV64360_PCI_ACC_CNTL_SNOOP_NONE |
-		    MV64360_PCI_ACC_CNTL_SWAP_NONE |
-		    MV64360_PCI_ACC_CNTL_MBURST_128_BYTES |
-		    MV64360_PCI_ACC_CNTL_RDSIZE_256_BYTES;
+			MV64360_PCI_ACC_CNTL_SNOOP_NONE |
+			MV64360_PCI_ACC_CNTL_SWAP_NONE |
+			MV64360_PCI_ACC_CNTL_MBURST_128_BYTES |
+			MV64360_PCI_ACC_CNTL_RDSIZE_256_BYTES;
 #else
 		si.cpu_prot_options[i] = 0;
-		si.enet_options[i] = MV64360_ENET2MEM_SNOOP_NONE; /* errata */
-		si.mpsc_options[i] = MV64360_MPSC2MEM_SNOOP_NONE; /* errata */
-		si.idma_options[i] = MV64360_IDMA2MEM_SNOOP_NONE; /* errata */
+		si.enet_options[i] = MV64360_ENET2MEM_SNOOP_WB;
+		si.mpsc_options[i] = MV64360_MPSC2MEM_SNOOP_WB;
+		si.idma_options[i] = MV64360_IDMA2MEM_SNOOP_WB;
 
 		si.pci_1.acc_cntl_options[i] =
-		    MV64360_PCI_ACC_CNTL_SNOOP_WB |
-		    MV64360_PCI_ACC_CNTL_SWAP_NONE |
-		    MV64360_PCI_ACC_CNTL_MBURST_32_BYTES |
-		    MV64360_PCI_ACC_CNTL_RDSIZE_32_BYTES;
+			MV64360_PCI_ACC_CNTL_SNOOP_WB |
+			MV64360_PCI_ACC_CNTL_SWAP_NONE |
+			MV64360_PCI_ACC_CNTL_MBURST_32_BYTES |
+			((type == PCI_DEVICE_ID_MARVELL_MV64360) ?
+				MV64360_PCI_ACC_CNTL_RDSIZE_32_BYTES :
+				MV64360_PCI_ACC_CNTL_RDSIZE_256_BYTES);
 #endif
 	}
 
@@ -281,12 +302,26 @@ katana_setup_bridge(void)
 	mv64x60_set_bus(&bh, 1, 0);
 	bh.hose_b->first_busno = 0;
 	bh.hose_b->last_busno = 0xff;
+
+	/*
+	 * Need to access hotswap reg which is in the pci config area of the
+	 * bridge's hose 0.  Note that pcibios_alloc_controller() can't be used
+	 * to alloc hose_a b/c that would make hose 0 known to the generic
+	 * pci code which we don't want.
+	 */
+	bh.hose_a = &katana_hose_a;
+	setup_indirect_pci_nomap(bh.hose_a,
+		bh.v_base + MV64x60_PCI0_CONFIG_ADDR,
+		bh.v_base + MV64x60_PCI0_CONFIG_DATA);
 }
 
 /* Bridge & platform setup routines */
 void __init
 katana_intr_setup(void)
 {
+	if (bh.type == MV64x60_TYPE_MV64460) /* As per instns from Marvell */
+		mv64x60_clr_bits(&bh, MV64x60_CPU_MASTER_CNTL, 1 << 15);
+
 	/* MPP 8, 9, and 10 */
 	mv64x60_clr_bits(&bh, MV64x60_MPP_CNTL_1, 0xfff);
 
@@ -309,9 +344,16 @@ katana_intr_setup(void)
 	/* Config GPP intr ctlr to respond to level trigger */
 	mv64x60_set_bits(&bh, MV64x60_COMM_ARBITER_CNTL, (1<<10));
 
-	/* Erranum FEr PCI-#8 */
-	mv64x60_clr_bits(&bh, MV64x60_PCI0_CMD, (1<<5) | (1<<9));
-	mv64x60_clr_bits(&bh, MV64x60_PCI1_CMD, (1<<5) | (1<<9));
+	if (bh.type == MV64x60_TYPE_MV64360) {
+		/* Erratum FEr PCI-#9 */
+		mv64x60_clr_bits(&bh, MV64x60_PCI1_CMD,
+				(1<<4) | (1<<5) | (1<<6) | (1<<7));
+		mv64x60_set_bits(&bh, MV64x60_PCI1_CMD, (1<<8) | (1<<9));
+	} else {
+		mv64x60_clr_bits(&bh, MV64x60_PCI1_CMD, (1<<6) | (1<<7));
+		mv64x60_set_bits(&bh, MV64x60_PCI1_CMD,
+				(1<<4) | (1<<5) | (1<<8) | (1<<9));
+	}
 
 	/*
 	 * Dismiss and then enable interrupt on GPP interrupt cause
@@ -473,17 +515,46 @@ katana_setup_arch(void)
 		ppc_md.progress("katana_setup_arch: exit", 0);
 }
 
+void
+katana_fixup_resources(struct pci_dev *dev)
+{
+	u16	v16;
+
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, L1_CACHE_LINE_SIZE>>2);
+
+	pci_read_config_word(dev, PCI_COMMAND, &v16);
+	v16 |= PCI_COMMAND_INVALIDATE | PCI_COMMAND_FAST_BACK;
+	pci_write_config_word(dev, PCI_COMMAND, v16);
+}
+
+static const unsigned int cpu_750xx[32] = { /* 750FX & 750GX */
+	 0,  0,  2,  2,  4,  5,  6,  7,  8,  9, 10, 11, 12, 13, 14, 15,/* 0-15*/
+	16, 17, 18, 19, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38, 40,  0 /*16-31*/
+};
+
+static int
+katana_get_cpu_freq(void)
+{
+	unsigned long	pll_cfg;
+
+	pll_cfg = (mfspr(SPRN_HID1) & 0xf8000000) >> 27;
+	return katana_bus_frequency * cpu_750xx[pll_cfg]/2;
+}
+
 /* Platform device data fixup routines. */
 #if defined(CONFIG_SERIAL_MPSC)
 static void __init
 katana_fixup_mpsc_pdata(struct platform_device *pdev)
 {
-	struct mpsc_pdata *pdata;
+	struct mpsc_pdata *pdata = (struct mpsc_pdata *)pdev->dev.platform_data;
+	bd_t *bdp = (bd_t *)__res;
 
-	pdata = (struct mpsc_pdata *)pdev->dev.platform_data;
+	if (bdp->bi_baudrate)
+		pdata->default_baud = bdp->bi_baudrate;
+	else
+		pdata->default_baud = KATANA_DEFAULT_BAUD;
 
 	pdata->max_idle = 40;
-	pdata->default_baud = KATANA_DEFAULT_BAUD;
 	pdata->brg_clk_src = KATANA_MPSC_CLK_SRC;
 	/*
 	 * TCLK (not SysCLk) is routed to BRG, then to the MPSC.  On most parts,
@@ -513,6 +584,18 @@ katana_fixup_eth_pdata(struct platform_device *pdev)
 }
 #endif
 
+#if defined(CONFIG_SYSFS)
+static void __init
+katana_fixup_mv64xxx_pdata(struct platform_device *pdev)
+{
+	struct mv64xxx_pdata *pdata = (struct mv64xxx_pdata *)
+		pdev->dev.platform_data;
+
+	/* Katana supports the mv64xxx hotswap register */
+	pdata->hs_reg_valid = 1;
+}
+#endif
+
 static int __init
 katana_platform_notify(struct device *dev)
 {
@@ -529,6 +612,9 @@ katana_platform_notify(struct device *dev)
 		{ MV643XX_ETH_NAME ".1", katana_fixup_eth_pdata },
 		{ MV643XX_ETH_NAME ".2", katana_fixup_eth_pdata },
 #endif
+#if defined(CONFIG_SYSFS)
+		{ MV64XXX_DEV_NAME ".0", katana_fixup_mv64xxx_pdata },
+#endif
 	};
 	struct platform_device	*pdev;
 	int	i;
@@ -536,8 +622,7 @@ katana_platform_notify(struct device *dev)
 	if (dev && dev->bus_id)
 		for (i=0; i<ARRAY_SIZE(dev_map); i++)
 			if (!strncmp(dev->bus_id, dev_map[i].bus_id,
-				BUS_ID_SIZE)) {
-
+					BUS_ID_SIZE)) {
 				pdev = container_of(dev,
 					struct platform_device, dev);
 				dev_map[i].rtn(pdev);
@@ -578,8 +663,7 @@ katana_setup_mtd(void)
 	ptbl_entries = (size >= (64*MB)) ? 6 : 4;
 
 	if ((ptbl = kmalloc(ptbl_entries * sizeof(struct mtd_partition),
-		GFP_KERNEL)) == NULL) {
-
+			GFP_KERNEL)) == NULL) {
 		printk(KERN_WARNING "Can't alloc MTD partition table\n");
 		return -ENOMEM;
 	}
@@ -611,7 +695,6 @@ katana_setup_mtd(void)
 	physmap_set_partitions(ptbl, ptbl_entries);
 	return 0;
 }
-
 arch_initcall(katana_setup_mtd);
 #endif
 
@@ -632,7 +715,22 @@ katana_halt(void)
 {
 	u8	v;
 
-	if (katana_id == KATANA_ID_752I) {
+	/* Turn on blue LED to indicate its okay to remove */
+	if (katana_id == KATANA_ID_750I) {
+		u32	v;
+		u8	save_exclude;
+
+		/* Set LOO bit in cPCI HotSwap reg of hose 0 to turn on LED. */
+		save_exclude = mv64x60_pci_exclude_bridge;
+		mv64x60_pci_exclude_bridge = 0;
+		early_read_config_dword(bh.hose_a, 0, PCI_DEVFN(0, 0),
+			MV64360_PCICFG_CPCI_HOTSWAP, &v);
+		v &= 0xff;
+		v |= (1 << 19);
+		early_write_config_dword(bh.hose_a, 0, PCI_DEVFN(0, 0),
+			MV64360_PCICFG_CPCI_HOTSWAP, v);
+		mv64x60_pci_exclude_bridge = save_exclude;
+	} else if (katana_id == KATANA_ID_752I) {
 		   v = in_8(cpld_base + HSL_PLD_BASE + HSL_PLD_HOT_SWAP_OFF);
 		   v |= HSL_PLD_HOT_SWAP_LED_BIT;
 		   out_8(cpld_base + HSL_PLD_BASE + HSL_PLD_HOT_SWAP_OFF, v);
@@ -652,37 +750,65 @@ katana_power_off(void)
 static int
 katana_show_cpuinfo(struct seq_file *m)
 {
+	char	*s;
+
+	seq_printf(m, "cpu freq\t: %dMHz\n",
+		(katana_get_cpu_freq() + 500000) / 1000000);
+	seq_printf(m, "bus freq\t: %ldMHz\n",
+		((long)katana_bus_frequency + 500000) / 1000000);
 	seq_printf(m, "vendor\t\t: Artesyn Communication Products, LLC\n");
 
 	seq_printf(m, "board\t\t: ");
-
 	switch (katana_id) {
 	case KATANA_ID_3750:
-		seq_printf(m, "Katana 3750\n");
+		seq_printf(m, "Katana 3750");
 		break;
 
 	case KATANA_ID_750I:
-		seq_printf(m, "Katana 750i\n");
+		seq_printf(m, "Katana 750i");
 		break;
 
 	case KATANA_ID_752I:
-		seq_printf(m, "Katana 752i\n");
+		seq_printf(m, "Katana 752i");
 		break;
 
 	default:
-		seq_printf(m, "Unknown\n");
+		seq_printf(m, "Unknown");
 		break;
 	}
-
-	seq_printf(m, "product ID\t: 0x%x\n",
+	seq_printf(m, " (product id: 0x%x)\n",
 		   in_8(cpld_base + KATANA_CPLD_PRODUCT_ID));
+
+	seq_printf(m, "pci mode\t: %sMonarch\n",
+		katana_is_monarch()? "" : "Non-");
 	seq_printf(m, "hardware rev\t: 0x%x\n",
 		   in_8(cpld_base+KATANA_CPLD_HARDWARE_VER));
-	seq_printf(m, "PLD rev\t\t: 0x%x\n",
+	seq_printf(m, "pld rev\t\t: 0x%x\n",
 		   in_8(cpld_base + KATANA_CPLD_PLD_VER));
-	seq_printf(m, "PLB freq\t: %ldMhz\n",
-		(long)katana_bus_frequency / 1000000);
-	seq_printf(m, "PCI\t\t: %sMonarch\n", katana_is_monarch()? "" : "Non-");
+
+	switch(bh.type) {
+	case MV64x60_TYPE_GT64260A:
+		s = "gt64260a";
+		break;
+	case MV64x60_TYPE_GT64260B:
+		s = "gt64260b";
+		break;
+	case MV64x60_TYPE_MV64360:
+		s = "mv64360";
+		break;
+	case MV64x60_TYPE_MV64460:
+		s = "mv64460";
+		break;
+	default:
+		s = "Unknown";
+	}
+	seq_printf(m, "bridge type\t: %s\n", s);
+	seq_printf(m, "bridge rev\t: 0x%x\n", bh.rev);
+#if defined(CONFIG_NOT_COHERENT_CACHE)
+	seq_printf(m, "coherency\t: %s\n", "off");
+#else
+	seq_printf(m, "coherency\t: %s\n", "on");
+#endif
 
 	return 0;
 }
@@ -701,11 +827,20 @@ katana_calibrate_decr(void)
 	tb_to_us = mulhwu_scale_factor(freq, 1000000);
 }
 
+/*
+ * The katana supports both uImage and zImage.  If uImage, get the mem size
+ * from the bd info.  If zImage, the bootwrapper adds a BI_MEMSIZE entry in
+ * the bi_rec data which is sucked out and put into boot_mem_size by
+ * parse_bootinfo().  MMU_init() will then use the boot_mem_size for the mem
+ * size and not call this routine.  The only way this will fail is when a uImage
+ * is used but the fw doesn't pass in a valid bi_memsize.  This should never
+ * happen, though.
+ */
 unsigned long __init
 katana_find_end_of_memory(void)
 {
-	return mv64x60_get_mem_size(CONFIG_MV64X60_NEW_BASE,
-		MV64x60_TYPE_MV64360);
+	bd_t *bdp = (bd_t *)__res;
+	return bdp->bi_memsize;
 }
 
 #if defined(CONFIG_I2C_MV64XXX) && defined(CONFIG_SENSORS_M41T00)
@@ -729,15 +864,6 @@ katana_rtc_hookup(void)
 late_initcall(katana_rtc_hookup);
 #endif
 
-static inline void
-katana_set_bat(void)
-{
-	mb();
-	mtspr(SPRN_DBAT2U, 0xf0001ffe);
-	mtspr(SPRN_DBAT2L, 0xf000002a);
-	mb();
-}
-
 #if defined(CONFIG_SERIAL_TEXT_DEBUG) && defined(CONFIG_SERIAL_MPSC_CONSOLE)
 static void __init
 katana_map_io(void)
@@ -763,15 +889,24 @@ platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
 	 */
 	if (r3 && r6) {
 		/* copy board info structure */
-		memcpy( (void *)__res,(void *)(r3+KERNELBASE), sizeof(bd_t) );
+		memcpy((void *)__res, (void *)(r3+KERNELBASE), sizeof(bd_t));
 		/* copy command line */
 		*(char *)(r7+KERNELBASE) = 0;
 		strcpy(cmd_line, (char *)(r6+KERNELBASE));
 	}
 
+#ifdef CONFIG_BLK_DEV_INITRD
+	/* take care of initrd if we have one */
+	if (r4) {
+		initrd_start = r4 + KERNELBASE;
+		initrd_end = r5 + KERNELBASE;
+	}
+#endif /* CONFIG_BLK_DEV_INITRD */
+
 	isa_mem_base = 0;
 
 	ppc_md.setup_arch = katana_setup_arch;
+	ppc_md.pcibios_fixup_resources = katana_fixup_resources;
 	ppc_md.show_cpuinfo = katana_show_cpuinfo;
 	ppc_md.init_IRQ = mv64360_init_irq;
 	ppc_md.get_irq = mv64360_get_irq;
@@ -790,6 +925,4 @@ platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
 #if defined(CONFIG_SERIAL_MPSC) || defined(CONFIG_MV643XX_ETH)
 	platform_notify = katana_platform_notify;
 #endif
-
-	katana_set_bat(); /* Need for katana_find_end_of_memory and progress */
 }
diff --git a/arch/ppc/platforms/katana.h b/arch/ppc/platforms/katana.h
index b82ed81950f..597257eff2e 100644
--- a/arch/ppc/platforms/katana.h
+++ b/arch/ppc/platforms/katana.h
@@ -56,14 +56,14 @@
 #define KATANA_PCI1_IO_SIZE                     0x04000000 /* 64 MB */
 
 /* Board-specific IRQ info */
-#define  KATANA_PCI_INTA_IRQ_3750		64+8
-#define  KATANA_PCI_INTB_IRQ_3750		64+9
-#define  KATANA_PCI_INTC_IRQ_3750		64+10
-
-#define  KATANA_PCI_INTA_IRQ_750i		64+8
-#define  KATANA_PCI_INTB_IRQ_750i		64+9
-#define  KATANA_PCI_INTC_IRQ_750i		64+10
-#define  KATANA_PCI_INTD_IRQ_750i		64+14
+#define  KATANA_PCI_INTA_IRQ_3750		(64+8)
+#define  KATANA_PCI_INTB_IRQ_3750		(64+9)
+#define  KATANA_PCI_INTC_IRQ_3750		(64+10)
+
+#define  KATANA_PCI_INTA_IRQ_750i		(64+8)
+#define  KATANA_PCI_INTB_IRQ_750i		(64+9)
+#define  KATANA_PCI_INTC_IRQ_750i		(64+10)
+#define  KATANA_PCI_INTD_IRQ_750i		(64+14)
 
 #define KATANA_CPLD_RST_EVENT			0x00000000
 #define KATANA_CPLD_RST_CMD			0x00001000