Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 89 insertions, 0 deletions

diff --git a/arch/i386/math-emu/fpu_system.h b/arch/i386/math-emu/fpu_system.h
new file mode 100644
index 00000000000..bf26341c8bd
--- /dev/null
+++ b/arch/i386/math-emu/fpu_system.h
@@ -0,0 +1,89 @@
+/*---------------------------------------------------------------------------+
+ |  fpu_system.h                                                             |
+ |                                                                           |
+ | Copyright (C) 1992,1994,1997                                              |
+ |                       W. Metzenthen, 22 Parker St, Ormond, Vic 3163,      |
+ |                       Australia.  E-mail   billm@suburbia.net             |
+ |                                                                           |
+ +---------------------------------------------------------------------------*/
+
+#ifndef _FPU_SYSTEM_H
+#define _FPU_SYSTEM_H
+
+/* system dependent definitions */
+
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+
+/* This sets the pointer FPU_info to point to the argument part
+   of the stack frame of math_emulate() */
+#define SETUP_DATA_AREA(arg)	FPU_info = (struct info *) &arg
+
+/* s is always from a cpu register, and the cpu does bounds checking
+ * during register load --> no further bounds checks needed */
+#define LDT_DESCRIPTOR(s)	(((struct desc_struct *)current->mm->context.ldt)[(s) >> 3])
+#define SEG_D_SIZE(x)		((x).b & (3 << 21))
+#define SEG_G_BIT(x)		((x).b & (1 << 23))
+#define SEG_GRANULARITY(x)	(((x).b & (1 << 23)) ? 4096 : 1)
+#define SEG_286_MODE(x)		((x).b & ( 0xff000000 | 0xf0000 | (1 << 23)))
+#define SEG_BASE_ADDR(s)	(((s).b & 0xff000000) \
+				 | (((s).b & 0xff) << 16) | ((s).a >> 16))
+#define SEG_LIMIT(s)		(((s).b & 0xff0000) | ((s).a & 0xffff))
+#define SEG_EXECUTE_ONLY(s)	(((s).b & ((1 << 11) | (1 << 9))) == (1 << 11))
+#define SEG_WRITE_PERM(s)	(((s).b & ((1 << 11) | (1 << 9))) == (1 << 9))
+#define SEG_EXPAND_DOWN(s)	(((s).b & ((1 << 11) | (1 << 10))) \
+				 == (1 << 10))
+
+#define I387			(current->thread.i387)
+#define FPU_info		(I387.soft.info)
+
+#define FPU_CS			(*(unsigned short *) &(FPU_info->___cs))
+#define FPU_SS			(*(unsigned short *) &(FPU_info->___ss))
+#define FPU_DS			(*(unsigned short *) &(FPU_info->___ds))
+#define FPU_EAX			(FPU_info->___eax)
+#define FPU_EFLAGS		(FPU_info->___eflags)
+#define FPU_EIP			(FPU_info->___eip)
+#define FPU_ORIG_EIP		(FPU_info->___orig_eip)
+
+#define FPU_lookahead           (I387.soft.lookahead)
+
+/* nz if ip_offset and cs_selector are not to be set for the current
+   instruction. */
+#define no_ip_update		(*(u_char *)&(I387.soft.no_update))
+#define FPU_rm			(*(u_char *)&(I387.soft.rm))
+
+/* Number of bytes of data which can be legally accessed by the current
+   instruction. This only needs to hold a number <= 108, so a byte will do. */
+#define access_limit		(*(u_char *)&(I387.soft.alimit))
+
+#define partial_status		(I387.soft.swd)
+#define control_word		(I387.soft.cwd)
+#define fpu_tag_word		(I387.soft.twd)
+#define registers		(I387.soft.st_space)
+#define top			(I387.soft.ftop)
+
+#define instruction_address	(*(struct address *)&I387.soft.fip)
+#define operand_address		(*(struct address *)&I387.soft.foo)
+
+#define FPU_access_ok(x,y,z)	if ( !access_ok(x,y,z) ) \
+				math_abort(FPU_info,SIGSEGV)
+
+#undef FPU_IGNORE_CODE_SEGV
+#ifdef FPU_IGNORE_CODE_SEGV
+/* access_ok() is very expensive, and causes the emulator to run
+   about 20% slower if applied to the code. Anyway, errors due to bad
+   code addresses should be much rarer than errors due to bad data
+   addresses. */
+#define	FPU_code_access_ok(z)
+#else
+/* A simpler test than access_ok() can probably be done for
+   FPU_code_access_ok() because the only possible error is to step
+   past the upper boundary of a legal code area. */
+#define	FPU_code_access_ok(z) FPU_access_ok(VERIFY_READ,(void __user *)FPU_EIP,z)
+#endif
+
+#define FPU_get_user(x,y)       get_user((x),(y))
+#define FPU_put_user(x,y)       put_user((x),(y))
+
+#endif