Blackfin arch: move include/asm-blackfin header files to arch/blackfin

Signed-off-by: Bryan Wu <cooloney@kernel.org>

19 files changed, 7799 insertions, 2 deletions

diff --git a/arch/blackfin/mach-bf527/head.S b/arch/blackfin/mach-bf527/head.S
index c3334cc5bcb..28c48619120 100644
--- a/arch/blackfin/mach-bf527/head.S
+++ b/arch/blackfin/mach-bf527/head.S
@@ -31,8 +31,8 @@
 #include <linux/init.h>
 #include <asm/blackfin.h>
 #ifdef CONFIG_BFIN_KERNEL_CLOCK
-#include <asm/mach-common/clocks.h>
-#include <asm/mach/mem_init.h>
+#include <asm/clocks.h>
+#include <mach/mem_init.h>
 #endif
 
 .section .l1.text
diff --git a/arch/blackfin/mach-bf527/include/mach/anomaly.h b/arch/blackfin/mach-bf527/include/mach/anomaly.h
new file mode 100644
index 00000000000..b7b166f4f06
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/anomaly.h
@@ -0,0 +1,104 @@
+/*
+ * File: include/asm-blackfin/mach-bf527/anomaly.h
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Copyright (C) 2004-2008 Analog Devices Inc.
+ * Licensed under the GPL-2 or later.
+ */
+
+/* This file shoule be up to date with:
+ *  - Revision C, 01/25/2008; ADSP-BF527 Blackfin Processor Anomaly List
+ */
+
+#ifndef _MACH_ANOMALY_H_
+#define _MACH_ANOMALY_H_
+
+/* Multi-Issue Instruction with dsp32shiftimm in slot1 and P-reg Store in slot2 Not Supported */
+#define ANOMALY_05000074 (1)
+/* DMA_RUN Bit Is Not Valid after a Peripheral Receive Channel DMA Stops */
+#define ANOMALY_05000119 (1)
+/* Rx.H Cannot Be Used to Access 16-bit System MMR Registers */
+#define ANOMALY_05000122 (1)
+/* Spurious Hardware Error from an Access in the Shadow of a Conditional Branch */
+#define ANOMALY_05000245 (1)
+/* Sensitivity To Noise with Slow Input Edge Rates on External SPORT TX and RX Clocks */
+#define ANOMALY_05000265 (1)
+/* New Feature: EMAC TX DMA Word Alignment */
+#define ANOMALY_05000285 (1)
+/* Errors when SSYNC, CSYNC, or Loads to LT, LB and LC Registers Are Interrupted */
+#define ANOMALY_05000312 (1)
+/* Incorrect Access of OTP_STATUS During otp_write() Function */
+#define ANOMALY_05000328 (1)
+/* Disallowed Configuration Prevents Subsequent Allowed Configuration on Host DMA Port */
+#define ANOMALY_05000337 (1)
+/* Ethernet MAC MDIO Reads Do Not Meet IEEE Specification */
+#define ANOMALY_05000341 (1)
+/* TWI May Not Operate Correctly Under Certain Signal Termination Conditions */
+#define ANOMALY_05000342 (1)
+/* USB Calibration Value Is Not Initialized */
+#define ANOMALY_05000346 (1)
+/* Preboot Routine Incorrectly Alters Reset Value of USB Register */
+#define ANOMALY_05000347 (1)
+/* Security Features Are Not Functional */
+#define ANOMALY_05000348 (__SILICON_REVISION__ < 1)
+/* Regulator Programming Blocked when Hibernate Wakeup Source Remains Active */
+#define ANOMALY_05000355 (1)
+/* Serial Port (SPORT) Multichannel Transmit Failure when Channel 0 Is Disabled */
+#define ANOMALY_05000357 (1)
+/* Incorrect Revision Number in DSPID Register */
+#define ANOMALY_05000364 (__SILICON_REVISION__ > 0)
+/* PPI Underflow Error Goes Undetected in ITU-R 656 Mode */
+#define ANOMALY_05000366 (1)
+/* New Feature: Higher Default CCLK Rate */
+#define ANOMALY_05000368 (1)
+/* Possible RETS Register Corruption when Subroutine Is under 5 Cycles in Duration */
+#define ANOMALY_05000371 (1)
+/* Authentication Fails To Initiate */
+#define ANOMALY_05000376 (__SILICON_REVISION__ > 0)
+/* Data Read From L3 Memory by USB DMA May be Corrupted */
+#define ANOMALY_05000380 (1)
+/* USB Full-speed Mode not Fully Tested */
+#define ANOMALY_05000381 (1)
+/* New Feature: Boot from OTP Memory */
+#define ANOMALY_05000385 (1)
+/* New Feature: bfrom_SysControl() Routine */
+#define ANOMALY_05000386 (1)
+/* New Feature: Programmable Preboot Settings */
+#define ANOMALY_05000387 (1)
+/* Reset Vector Must Not Be in SDRAM Memory Space */
+#define ANOMALY_05000389 (1)
+/* New Feature: pTempCurrent Added to ADI_BOOT_DATA Structure */
+#define ANOMALY_05000392 (1)
+/* New Feature: dTempByteCount Value Increased in ADI_BOOT_DATA Structure */
+#define ANOMALY_05000393 (1)
+/* New Feature: Log Buffer Functionality */
+#define ANOMALY_05000394 (1)
+/* New Feature: Hook Routine Functionality */
+#define ANOMALY_05000395 (1)
+/* New Feature: Header Indirect Bit */
+#define ANOMALY_05000396 (1)
+/* New Feature: BK_ONES, BK_ZEROS, and BK_DATECODE Constants */
+#define ANOMALY_05000397 (1)
+/* New Feature: SWRESET, DFRESET and WDRESET Bits Added to SYSCR Register */
+#define ANOMALY_05000398 (1)
+/* New Feature: BCODE_NOBOOT Added to BCODE Field of SYSCR Register */
+#define ANOMALY_05000399 (1)
+/* PPI Data Signals D0 and D8 do not Tristate After Disabling PPI */
+#define ANOMALY_05000401 (1)
+
+/* Anomalies that don't exist on this proc */
+#define ANOMALY_05000125 (0)
+#define ANOMALY_05000158 (0)
+#define ANOMALY_05000183 (0)
+#define ANOMALY_05000198 (0)
+#define ANOMALY_05000230 (0)
+#define ANOMALY_05000244 (0)
+#define ANOMALY_05000261 (0)
+#define ANOMALY_05000263 (0)
+#define ANOMALY_05000266 (0)
+#define ANOMALY_05000273 (0)
+#define ANOMALY_05000311 (0)
+#define ANOMALY_05000323 (0)
+#define ANOMALY_05000363 (0)
+
+#endif
diff --git a/arch/blackfin/mach-bf527/include/mach/bf527.h b/arch/blackfin/mach-bf527/include/mach/bf527.h
new file mode 100644
index 00000000000..056eb4b9cd2
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/bf527.h
@@ -0,0 +1,127 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/bf527.h
+ * Based on:	include/asm-blackfin/mach-bf537/bf537.h
+ * Author:	Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * Created:
+ * Description:  SYSTEM MMR REGISTER AND MEMORY MAP FOR ADSP-BF527
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#ifndef __MACH_BF527_H__
+#define __MACH_BF527_H__
+
+#define SUPPORTED_REVID 2
+
+#define OFFSET_(x) ((x) & 0x0000FFFF)
+
+/*some misc defines*/
+#define IMASK_IVG15		0x8000
+#define IMASK_IVG14		0x4000
+#define IMASK_IVG13		0x2000
+#define IMASK_IVG12		0x1000
+
+#define IMASK_IVG11		0x0800
+#define IMASK_IVG10		0x0400
+#define IMASK_IVG9		0x0200
+#define IMASK_IVG8		0x0100
+
+#define IMASK_IVG7		0x0080
+#define IMASK_IVGTMR	0x0040
+#define IMASK_IVGHW		0x0020
+
+/***************************/
+
+#define BFIN_DSUBBANKS	4
+#define BFIN_DWAYS		2
+#define BFIN_DLINES		64
+#define BFIN_ISUBBANKS	4
+#define BFIN_IWAYS		4
+#define BFIN_ILINES		32
+
+#define WAY0_L			0x1
+#define WAY1_L			0x2
+#define WAY01_L			0x3
+#define WAY2_L			0x4
+#define WAY02_L			0x5
+#define	WAY12_L			0x6
+#define	WAY012_L		0x7
+
+#define	WAY3_L			0x8
+#define	WAY03_L			0x9
+#define	WAY13_L			0xA
+#define	WAY013_L		0xB
+
+#define	WAY32_L			0xC
+#define	WAY320_L		0xD
+#define	WAY321_L		0xE
+#define	WAYALL_L		0xF
+
+#define DMC_ENABLE (2<<2)	/*yes, 2, not 1 */
+
+/********************************* EBIU Settings ************************************/
+#define AMBCTL0VAL	((CONFIG_BANK_1 << 16) | CONFIG_BANK_0)
+#define AMBCTL1VAL	((CONFIG_BANK_3 << 16) | CONFIG_BANK_2)
+
+#ifdef CONFIG_C_AMBEN_ALL
+#define V_AMBEN AMBEN_ALL
+#endif
+#ifdef CONFIG_C_AMBEN
+#define V_AMBEN 0x0
+#endif
+#ifdef CONFIG_C_AMBEN_B0
+#define V_AMBEN AMBEN_B0
+#endif
+#ifdef CONFIG_C_AMBEN_B0_B1
+#define V_AMBEN AMBEN_B0_B1
+#endif
+#ifdef CONFIG_C_AMBEN_B0_B1_B2
+#define V_AMBEN AMBEN_B0_B1_B2
+#endif
+#ifdef CONFIG_C_AMCKEN
+#define V_AMCKEN AMCKEN
+#else
+#define V_AMCKEN 0x0
+#endif
+#ifdef CONFIG_C_CDPRIO
+#define V_CDPRIO 0x100
+#else
+#define V_CDPRIO 0x0
+#endif
+
+#define AMGCTLVAL	(V_AMBEN | V_AMCKEN | V_CDPRIO)
+
+#ifdef CONFIG_BF527
+#define CPU "BF527"
+#endif
+#ifdef CONFIG_BF525
+#define CPU "BF525"
+#endif
+#ifdef CONFIG_BF522
+#define CPU "BF522"
+#endif
+#ifndef CPU
+#define	CPU "UNKNOWN"
+#define CPUID 0x0
+#endif
+
+#endif				/* __MACH_BF527_H__  */
diff --git a/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h b/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
new file mode 100644
index 00000000000..2526b6ed6fa
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/bfin_serial_5xx.h
@@ -0,0 +1,195 @@
+/*
+ * file:        include/asm-blackfin/mach-bf527/bfin_serial_5xx.h
+ * based on:
+ * author:
+ *
+ * created:
+ * description:
+ *	blackfin serial driver head file
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define UART_GET_CHAR(uart)     bfin_read16(((uart)->port.membase + OFFSET_RBR))
+#define UART_GET_DLL(uart)	bfin_read16(((uart)->port.membase + OFFSET_DLL))
+#define UART_GET_IER(uart)      bfin_read16(((uart)->port.membase + OFFSET_IER))
+#define UART_GET_DLH(uart)	bfin_read16(((uart)->port.membase + OFFSET_DLH))
+#define UART_GET_IIR(uart)      bfin_read16(((uart)->port.membase + OFFSET_IIR))
+#define UART_GET_LCR(uart)      bfin_read16(((uart)->port.membase + OFFSET_LCR))
+#define UART_GET_GCTL(uart)     bfin_read16(((uart)->port.membase + OFFSET_GCTL))
+
+#define UART_PUT_CHAR(uart, v)   bfin_write16(((uart)->port.membase + OFFSET_THR), v)
+#define UART_PUT_DLL(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_DLL), v)
+#define UART_PUT_IER(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_IER), v)
+#define UART_SET_IER(uart, v)    UART_PUT_IER(uart, UART_GET_IER(uart) | (v))
+#define UART_CLEAR_IER(uart, v)  UART_PUT_IER(uart, UART_GET_IER(uart) & ~(v))
+#define UART_PUT_DLH(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_DLH), v)
+#define UART_PUT_LCR(uart, v)    bfin_write16(((uart)->port.membase + OFFSET_LCR), v)
+#define UART_PUT_GCTL(uart, v)   bfin_write16(((uart)->port.membase + OFFSET_GCTL), v)
+
+#define UART_SET_DLAB(uart)     do { UART_PUT_LCR(uart, UART_GET_LCR(uart) | DLAB); SSYNC(); } while (0)
+#define UART_CLEAR_DLAB(uart)   do { UART_PUT_LCR(uart, UART_GET_LCR(uart) & ~DLAB); SSYNC(); } while (0)
+
+#define UART_GET_CTS(x) gpio_get_value(x->cts_pin)
+#define UART_SET_RTS(x) gpio_set_value(x->rts_pin, 1)
+#define UART_CLEAR_RTS(x) gpio_set_value(x->rts_pin, 0)
+#define UART_ENABLE_INTS(x, v) UART_PUT_IER(x, v)
+#define UART_DISABLE_INTS(x) UART_PUT_IER(x, 0)
+
+#if defined(CONFIG_BFIN_UART0_CTSRTS) || defined(CONFIG_BFIN_UART1_CTSRTS)
+# define CONFIG_SERIAL_BFIN_CTSRTS
+
+# ifndef CONFIG_UART0_CTS_PIN
+#  define CONFIG_UART0_CTS_PIN -1
+# endif
+
+# ifndef CONFIG_UART0_RTS_PIN
+#  define CONFIG_UART0_RTS_PIN -1
+# endif
+
+# ifndef CONFIG_UART1_CTS_PIN
+#  define CONFIG_UART1_CTS_PIN -1
+# endif
+
+# ifndef CONFIG_UART1_RTS_PIN
+#  define CONFIG_UART1_RTS_PIN -1
+# endif
+#endif
+/*
+ * The pin configuration is different from schematic
+ */
+struct bfin_serial_port {
+	struct uart_port port;
+	unsigned int old_status;
+	unsigned int lsr;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	int tx_done;
+	int tx_count;
+	struct circ_buf rx_dma_buf;
+	struct timer_list rx_dma_timer;
+	int rx_dma_nrows;
+	unsigned int tx_dma_channel;
+	unsigned int rx_dma_channel;
+	struct work_struct tx_dma_workqueue;
+#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	struct timer_list cts_timer;
+	int cts_pin;
+	int rts_pin;
+#endif
+};
+
+/* The hardware clears the LSR bits upon read, so we need to cache
+ * some of the more fun bits in software so they don't get lost
+ * when checking the LSR in other code paths (TX).
+ */
+static inline unsigned int UART_GET_LSR(struct bfin_serial_port *uart)
+{
+	unsigned int lsr = bfin_read16(uart->port.membase + OFFSET_LSR);
+	uart->lsr |= (lsr & (BI|FE|PE|OE));
+	return lsr | uart->lsr;
+}
+
+static inline void UART_CLEAR_LSR(struct bfin_serial_port *uart)
+{
+	uart->lsr = 0;
+	bfin_write16(uart->port.membase + OFFSET_LSR, -1);
+}
+
+struct bfin_serial_port bfin_serial_ports[BFIN_UART_NR_PORTS];
+struct bfin_serial_res {
+	unsigned long uart_base_addr;
+	int uart_irq;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	unsigned int uart_tx_dma_channel;
+	unsigned int uart_rx_dma_channel;
+#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	int uart_cts_pin;
+	int uart_rts_pin;
+#endif
+};
+
+struct bfin_serial_res bfin_serial_resource[] = {
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	{
+	 0xFFC00400,
+	 IRQ_UART0_RX,
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	 CH_UART0_TX,
+	 CH_UART0_RX,
+#endif
+#ifdef CONFIG_BFIN_UART0_CTSRTS
+	 CONFIG_UART0_CTS_PIN,
+	 CONFIG_UART0_RTS_PIN,
+#endif
+	 },
+#endif
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	{
+	 0xFFC02000,
+	 IRQ_UART1_RX,
+#ifdef CONFIG_SERIAL_BFIN_DMA
+	 CH_UART1_TX,
+	 CH_UART1_RX,
+#endif
+#ifdef CONFIG_BFIN_UART1_CTSRTS
+	 CONFIG_UART1_CTS_PIN,
+	 CONFIG_UART1_RTS_PIN,
+#endif
+	 },
+#endif
+};
+
+int nr_ports = ARRAY_SIZE(bfin_serial_resource);
+
+#define DRIVER_NAME "bfin-uart"
+
+static void bfin_serial_hw_init(struct bfin_serial_port *uart)
+{
+
+#ifdef CONFIG_SERIAL_BFIN_UART0
+	peripheral_request(P_UART0_TX, DRIVER_NAME);
+	peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART1
+	peripheral_request(P_UART1_TX, DRIVER_NAME);
+	peripheral_request(P_UART1_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+	if (uart->cts_pin >= 0) {
+		gpio_request(uart->cts_pin, DRIVER_NAME);
+		gpio_direction_input(uart->cts_pin);
+	}
+
+	if (uart->rts_pin >= 0) {
+		gpio_request(uart->rts_pin, DRIVER_NAME);
+		gpio_direction_output(uart->rts_pin, 0);
+	}
+#endif
+}
diff --git a/arch/blackfin/mach-bf527/include/mach/bfin_sir.h b/arch/blackfin/mach-bf527/include/mach/bfin_sir.h
new file mode 100644
index 00000000000..cfd8ad4f1f2
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/bfin_sir.h
@@ -0,0 +1,142 @@
+/*
+ * Blackfin Infra-red Driver
+ *
+ * Copyright 2006-2008 Analog Devices Inc.
+ *
+ * Enter bugs at http://blackfin.uclinux.org/
+ *
+ * Licensed under the GPL-2 or later.
+ *
+ */
+
+#include <linux/serial.h>
+#include <asm/dma.h>
+#include <asm/portmux.h>
+
+#define SIR_UART_GET_CHAR(port)   bfin_read16((port)->membase + OFFSET_RBR)
+#define SIR_UART_GET_DLL(port)    bfin_read16((port)->membase + OFFSET_DLL)
+#define SIR_UART_GET_IER(port)    bfin_read16((port)->membase + OFFSET_IER)
+#define SIR_UART_GET_DLH(port)    bfin_read16((port)->membase + OFFSET_DLH)
+#define SIR_UART_GET_IIR(port)    bfin_read16((port)->membase + OFFSET_IIR)
+#define SIR_UART_GET_LCR(port)    bfin_read16((port)->membase + OFFSET_LCR)
+#define SIR_UART_GET_GCTL(port)   bfin_read16((port)->membase + OFFSET_GCTL)
+
+#define SIR_UART_PUT_CHAR(port, v) bfin_write16(((port)->membase + OFFSET_THR), v)
+#define SIR_UART_PUT_DLL(port, v)  bfin_write16(((port)->membase + OFFSET_DLL), v)
+#define SIR_UART_PUT_IER(port, v)  bfin_write16(((port)->membase + OFFSET_IER), v)
+#define SIR_UART_PUT_DLH(port, v)  bfin_write16(((port)->membase + OFFSET_DLH), v)
+#define SIR_UART_PUT_LCR(port, v)  bfin_write16(((port)->membase + OFFSET_LCR), v)
+#define SIR_UART_PUT_GCTL(port, v) bfin_write16(((port)->membase + OFFSET_GCTL), v)
+
+#ifdef CONFIG_SIR_BFIN_DMA
+struct dma_rx_buf {
+	char *buf;
+	int head;
+	int tail;
+	};
+#endif /* CONFIG_SIR_BFIN_DMA */
+
+struct bfin_sir_port {
+	unsigned char __iomem   *membase;
+	unsigned int            irq;
+	unsigned int            lsr;
+	unsigned long           clk;
+	struct net_device       *dev;
+#ifdef CONFIG_SIR_BFIN_DMA
+	int                     tx_done;
+	struct dma_rx_buf       rx_dma_buf;
+	struct timer_list       rx_dma_timer;
+	int                     rx_dma_nrows;
+#endif /* CONFIG_SIR_BFIN_DMA */
+	unsigned int            tx_dma_channel;
+	unsigned int            rx_dma_channel;
+};
+
+struct bfin_sir_port sir_ports[BFIN_UART_NR_PORTS];
+
+struct bfin_sir_port_res {
+	unsigned long   base_addr;
+	int             irq;
+	unsigned int    rx_dma_channel;
+	unsigned int    tx_dma_channel;
+};
+
+struct bfin_sir_port_res bfin_sir_port_resource[] = {
+#ifdef CONFIG_BFIN_SIR0
+	{
+	0xFFC00400,
+	IRQ_UART0_RX,
+	CH_UART0_RX,
+	CH_UART0_TX,
+	},
+#endif
+#ifdef CONFIG_BFIN_SIR1
+	{
+	0xFFC02000,
+	IRQ_UART1_RX,
+	CH_UART1_RX,
+	CH_UART1_TX,
+	},
+#endif
+};
+
+int nr_sirs = ARRAY_SIZE(bfin_sir_port_resource);
+
+struct bfin_sir_self {
+	struct bfin_sir_port    *sir_port;
+	spinlock_t              lock;
+	unsigned int            open;
+	int                     speed;
+	int                     newspeed;
+
+	struct sk_buff          *txskb;
+	struct sk_buff          *rxskb;
+	struct net_device_stats stats;
+	struct device           *dev;
+	struct irlap_cb         *irlap;
+	struct qos_info         qos;
+
+	iobuff_t                tx_buff;
+	iobuff_t                rx_buff;
+
+	struct work_struct      work;
+	int                     mtt;
+};
+
+static inline unsigned int SIR_UART_GET_LSR(struct bfin_sir_port *port)
+{
+	unsigned int lsr = bfin_read16(port->membase + OFFSET_LSR);
+	port->lsr |= (lsr & (BI|FE|PE|OE));
+	return lsr | port->lsr;
+}
+
+static inline void SIR_UART_CLEAR_LSR(struct bfin_sir_port *port)
+{
+	port->lsr = 0;
+	bfin_read16(port->membase + OFFSET_LSR);
+}
+
+#define DRIVER_NAME "bfin_sir"
+
+static int bfin_sir_hw_init(void)
+{
+	int ret = -ENODEV;
+#ifdef CONFIG_BFIN_SIR0
+	ret = peripheral_request(P_UART0_TX, DRIVER_NAME);
+	if (ret)
+		return ret;
+	ret = peripheral_request(P_UART0_RX, DRIVER_NAME);
+	if (ret)
+		return ret;
+#endif
+
+#ifdef CONFIG_BFIN_SIR1
+	ret = peripheral_request(P_UART1_TX, DRIVER_NAME);
+	if (ret)
+		return ret;
+	ret = peripheral_request(P_UART1_RX, DRIVER_NAME);
+	if (ret)
+		return ret;
+#endif
+	return ret;
+}
diff --git a/arch/blackfin/mach-bf527/include/mach/blackfin.h b/arch/blackfin/mach-bf527/include/mach/blackfin.h
new file mode 100644
index 00000000000..297821e2d79
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/blackfin.h
@@ -0,0 +1,93 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/blackfin.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _MACH_BLACKFIN_H_
+#define _MACH_BLACKFIN_H_
+
+#define BF527_FAMILY
+
+#include "bf527.h"
+#include "mem_map.h"
+#include "defBF522.h"
+#include "anomaly.h"
+
+#if defined(CONFIG_BF527) || defined(CONFIG_BF526)
+#include "defBF527.h"
+#endif
+
+#if defined(CONFIG_BF525) || defined(CONFIG_BF524)
+#include "defBF525.h"
+#endif
+
+#if !defined(__ASSEMBLY__)
+#include "cdefBF522.h"
+
+#if defined(CONFIG_BF527) || defined(CONFIG_BF526)
+#include "cdefBF527.h"
+#endif
+
+#if defined(CONFIG_BF525) || defined(CONFIG_BF524)
+#include "cdefBF525.h"
+#endif
+#endif
+
+/* UART_IIR Register */
+#define STATUS(x)	((x << 1) & 0x06)
+#define STATUS_P1	0x02
+#define STATUS_P0	0x01
+
+#define BFIN_UART_NR_PORTS	2
+
+#define OFFSET_THR              0x00	/* Transmit Holding register            */
+#define OFFSET_RBR              0x00	/* Receive Buffer register              */
+#define OFFSET_DLL              0x00	/* Divisor Latch (Low-Byte)             */
+#define OFFSET_IER              0x04	/* Interrupt Enable Register            */
+#define OFFSET_DLH              0x04	/* Divisor Latch (High-Byte)            */
+#define OFFSET_IIR              0x08	/* Interrupt Identification Register    */
+#define OFFSET_LCR              0x0C	/* Line Control Register                */
+#define OFFSET_MCR              0x10	/* Modem Control Register               */
+#define OFFSET_LSR              0x14	/* Line Status Register                 */
+#define OFFSET_MSR              0x18	/* Modem Status Register                */
+#define OFFSET_SCR              0x1C	/* SCR Scratch Register                 */
+#define OFFSET_GCTL             0x24	/* Global Control Register              */
+
+/* DPMC*/
+#define bfin_read_STOPCK_OFF() bfin_read_STOPCK()
+#define bfin_write_STOPCK_OFF(val) bfin_write_STOPCK(val)
+#define STOPCK_OFF STOPCK
+
+/* PLL_DIV Masks													*/
+#define CCLK_DIV1 CSEL_DIV1	/*          CCLK = VCO / 1                                  */
+#define CCLK_DIV2 CSEL_DIV2	/*          CCLK = VCO / 2                                  */
+#define CCLK_DIV4 CSEL_DIV4	/*          CCLK = VCO / 4                                  */
+#define CCLK_DIV8 CSEL_DIV8	/*          CCLK = VCO / 8                                  */
+
+#endif
diff --git a/arch/blackfin/mach-bf527/include/mach/cdefBF522.h b/arch/blackfin/mach-bf527/include/mach/cdefBF522.h
new file mode 100644
index 00000000000..663c2bbdfd9
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/cdefBF522.h
@@ -0,0 +1,46 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/cdefbf522.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:  system mmr register map
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _CDEF_BF522_H
+#define _CDEF_BF522_H
+
+/* include all Core registers and bit definitions */
+#include "defBF522.h"
+
+/* include core specific register pointer definitions */
+#include <asm/cdef_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF522 */
+
+/* include cdefBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */
+#include "cdefBF52x_base.h"
+
+#endif /* _CDEF_BF522_H */
diff --git a/arch/blackfin/mach-bf527/include/mach/cdefBF525.h b/arch/blackfin/mach-bf527/include/mach/cdefBF525.h
new file mode 100644
index 00000000000..00377eb59b7
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/cdefBF525.h
@@ -0,0 +1,461 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/cdefbf525.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:  system mmr register map
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _CDEF_BF525_H
+#define _CDEF_BF525_H
+
+/* include all Core registers and bit definitions */
+#include "defBF525.h"
+
+/* include core specific register pointer definitions */
+#include <asm/cdef_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF525 */
+
+/* include cdefBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */
+#include "cdefBF52x_base.h"
+
+/* The following are the #defines needed by ADSP-BF525 that are not in the common header */
+
+/* USB Control Registers */
+
+#define bfin_read_USB_FADDR()			bfin_read16(USB_FADDR)
+#define bfin_write_USB_FADDR(val)		bfin_write16(USB_FADDR, val)
+#define bfin_read_USB_POWER()			bfin_read16(USB_POWER)
+#define bfin_write_USB_POWER(val)		bfin_write16(USB_POWER, val)
+#define bfin_read_USB_INTRTX()			bfin_read16(USB_INTRTX)
+#define bfin_write_USB_INTRTX(val)		bfin_write16(USB_INTRTX, val)
+#define bfin_read_USB_INTRRX()			bfin_read16(USB_INTRRX)
+#define bfin_write_USB_INTRRX(val)		bfin_write16(USB_INTRRX, val)
+#define bfin_read_USB_INTRTXE()			bfin_read16(USB_INTRTXE)
+#define bfin_write_USB_INTRTXE(val)		bfin_write16(USB_INTRTXE, val)
+#define bfin_read_USB_INTRRXE()			bfin_read16(USB_INTRRXE)
+#define bfin_write_USB_INTRRXE(val)		bfin_write16(USB_INTRRXE, val)
+#define bfin_read_USB_INTRUSB()			bfin_read16(USB_INTRUSB)
+#define bfin_write_USB_INTRUSB(val)		bfin_write16(USB_INTRUSB, val)
+#define bfin_read_USB_INTRUSBE()		bfin_read16(USB_INTRUSBE)
+#define bfin_write_USB_INTRUSBE(val)		bfin_write16(USB_INTRUSBE, val)
+#define bfin_read_USB_FRAME()			bfin_read16(USB_FRAME)
+#define bfin_write_USB_FRAME(val)		bfin_write16(USB_FRAME, val)
+#define bfin_read_USB_INDEX()			bfin_read16(USB_INDEX)
+#define bfin_write_USB_INDEX(val)		bfin_write16(USB_INDEX, val)
+#define bfin_read_USB_TESTMODE()		bfin_read16(USB_TESTMODE)
+#define bfin_write_USB_TESTMODE(val)		bfin_write16(USB_TESTMODE, val)
+#define bfin_read_USB_GLOBINTR()		bfin_read16(USB_GLOBINTR)
+#define bfin_write_USB_GLOBINTR(val)		bfin_write16(USB_GLOBINTR, val)
+#define bfin_read_USB_GLOBAL_CTL()		bfin_read16(USB_GLOBAL_CTL)
+#define bfin_write_USB_GLOBAL_CTL(val)		bfin_write16(USB_GLOBAL_CTL, val)
+
+/* USB Packet Control Registers */
+
+#define bfin_read_USB_TX_MAX_PACKET()		bfin_read16(USB_TX_MAX_PACKET)
+#define bfin_write_USB_TX_MAX_PACKET(val)	bfin_write16(USB_TX_MAX_PACKET, val)
+#define bfin_read_USB_CSR0()			bfin_read16(USB_CSR0)
+#define bfin_write_USB_CSR0(val)		bfin_write16(USB_CSR0, val)
+#define bfin_read_USB_TXCSR()			bfin_read16(USB_TXCSR)
+#define bfin_write_USB_TXCSR(val)		bfin_write16(USB_TXCSR, val)
+#define bfin_read_USB_RX_MAX_PACKET()		bfin_read16(USB_RX_MAX_PACKET)
+#define bfin_write_USB_RX_MAX_PACKET(val)	bfin_write16(USB_RX_MAX_PACKET, val)
+#define bfin_read_USB_RXCSR()			bfin_read16(USB_RXCSR)
+#define bfin_write_USB_RXCSR(val)		bfin_write16(USB_RXCSR, val)
+#define bfin_read_USB_COUNT0()			bfin_read16(USB_COUNT0)
+#define bfin_write_USB_COUNT0(val)		bfin_write16(USB_COUNT0, val)
+#define bfin_read_USB_RXCOUNT()			bfin_read16(USB_RXCOUNT)
+#define bfin_write_USB_RXCOUNT(val)		bfin_write16(USB_RXCOUNT, val)
+#define bfin_read_USB_TXTYPE()			bfin_read16(USB_TXTYPE)
+#define bfin_write_USB_TXTYPE(val)		bfin_write16(USB_TXTYPE, val)
+#define bfin_read_USB_NAKLIMIT0()		bfin_read16(USB_NAKLIMIT0)
+#define bfin_write_USB_NAKLIMIT0(val)		bfin_write16(USB_NAKLIMIT0, val)
+#define bfin_read_USB_TXINTERVAL()		bfin_read16(USB_TXINTERVAL)
+#define bfin_write_USB_TXINTERVAL(val)		bfin_write16(USB_TXINTERVAL, val)
+#define bfin_read_USB_RXTYPE()			bfin_read16(USB_RXTYPE)
+#define bfin_write_USB_RXTYPE(val)		bfin_write16(USB_RXTYPE, val)
+#define bfin_read_USB_RXINTERVAL()		bfin_read16(USB_RXINTERVAL)
+#define bfin_write_USB_RXINTERVAL(val)		bfin_write16(USB_RXINTERVAL, val)
+#define bfin_read_USB_TXCOUNT()			bfin_read16(USB_TXCOUNT)
+#define bfin_write_USB_TXCOUNT(val)		bfin_write16(USB_TXCOUNT, val)
+
+/* USB Endpoint FIFO Registers */
+
+#define bfin_read_USB_EP0_FIFO()		bfin_read16(USB_EP0_FIFO)
+#define bfin_write_USB_EP0_FIFO(val)		bfin_write16(USB_EP0_FIFO, val)
+#define bfin_read_USB_EP1_FIFO()		bfin_read16(USB_EP1_FIFO)
+#define bfin_write_USB_EP1_FIFO(val)		bfin_write16(USB_EP1_FIFO, val)
+#define bfin_read_USB_EP2_FIFO()		bfin_read16(USB_EP2_FIFO)
+#define bfin_write_USB_EP2_FIFO(val)		bfin_write16(USB_EP2_FIFO, val)
+#define bfin_read_USB_EP3_FIFO()		bfin_read16(USB_EP3_FIFO)
+#define bfin_write_USB_EP3_FIFO(val)		bfin_write16(USB_EP3_FIFO, val)
+#define bfin_read_USB_EP4_FIFO()		bfin_read16(USB_EP4_FIFO)
+#define bfin_write_USB_EP4_FIFO(val)		bfin_write16(USB_EP4_FIFO, val)
+#define bfin_read_USB_EP5_FIFO()		bfin_read16(USB_EP5_FIFO)
+#define bfin_write_USB_EP5_FIFO(val)		bfin_write16(USB_EP5_FIFO, val)
+#define bfin_read_USB_EP6_FIFO()		bfin_read16(USB_EP6_FIFO)
+#define bfin_write_USB_EP6_FIFO(val)		bfin_write16(USB_EP6_FIFO, val)
+#define bfin_read_USB_EP7_FIFO()		bfin_read16(USB_EP7_FIFO)
+#define bfin_write_USB_EP7_FIFO(val)		bfin_write16(USB_EP7_FIFO, val)
+
+/* USB OTG Control Registers */
+
+#define bfin_read_USB_OTG_DEV_CTL()		bfin_read16(USB_OTG_DEV_CTL)
+#define bfin_write_USB_OTG_DEV_CTL(val)		bfin_write16(USB_OTG_DEV_CTL, val)
+#define bfin_read_USB_OTG_VBUS_IRQ()		bfin_read16(USB_OTG_VBUS_IRQ)
+#define bfin_write_USB_OTG_VBUS_IRQ(val)	bfin_write16(USB_OTG_VBUS_IRQ, val)
+#define bfin_read_USB_OTG_VBUS_MASK()		bfin_read16(USB_OTG_VBUS_MASK)
+#define bfin_write_USB_OTG_VBUS_MASK(val)	bfin_write16(USB_OTG_VBUS_MASK, val)
+
+/* USB Phy Control Registers */
+
+#define bfin_read_USB_LINKINFO()		bfin_read16(USB_LINKINFO)
+#define bfin_write_USB_LINKINFO(val)		bfin_write16(USB_LINKINFO, val)
+#define bfin_read_USB_VPLEN()			bfin_read16(USB_VPLEN)
+#define bfin_write_USB_VPLEN(val)		bfin_write16(USB_VPLEN, val)
+#define bfin_read_USB_HS_EOF1()			bfin_read16(USB_HS_EOF1)
+#define bfin_write_USB_HS_EOF1(val)		bfin_write16(USB_HS_EOF1, val)
+#define bfin_read_USB_FS_EOF1()			bfin_read16(USB_FS_EOF1)
+#define bfin_write_USB_FS_EOF1(val)		bfin_write16(USB_FS_EOF1, val)
+#define bfin_read_USB_LS_EOF1()			bfin_read16(USB_LS_EOF1)
+#define bfin_write_USB_LS_EOF1(val)		bfin_write16(USB_LS_EOF1, val)
+
+/* (APHY_CNTRL is for ADI usage only) */
+
+#define bfin_read_USB_APHY_CNTRL()		bfin_read16(USB_APHY_CNTRL)
+#define bfin_write_USB_APHY_CNTRL(val)		bfin_write16(USB_APHY_CNTRL, val)
+
+/* (APHY_CALIB is for ADI usage only) */
+
+#define bfin_read_USB_APHY_CALIB()		bfin_read16(USB_APHY_CALIB)
+#define bfin_write_USB_APHY_CALIB(val)		bfin_write16(USB_APHY_CALIB, val)
+
+#define bfin_read_USB_APHY_CNTRL2()		bfin_read16(USB_APHY_CNTRL2)
+#define bfin_write_USB_APHY_CNTRL2(val)		bfin_write16(USB_APHY_CNTRL2, val)
+
+/* (PHY_TEST is for ADI usage only) */
+
+#define bfin_read_USB_PHY_TEST()		bfin_read16(USB_PHY_TEST)
+#define bfin_write_USB_PHY_TEST(val)		bfin_write16(USB_PHY_TEST, val)
+
+#define bfin_read_USB_PLLOSC_CTRL()		bfin_read16(USB_PLLOSC_CTRL)
+#define bfin_write_USB_PLLOSC_CTRL(val)		bfin_write16(USB_PLLOSC_CTRL, val)
+#define bfin_read_USB_SRP_CLKDIV()		bfin_read16(USB_SRP_CLKDIV)
+#define bfin_write_USB_SRP_CLKDIV(val)		bfin_write16(USB_SRP_CLKDIV, val)
+
+/* USB Endpoint 0 Control Registers */
+
+#define bfin_read_USB_EP_NI0_TXMAXP()		bfin_read16(USB_EP_NI0_TXMAXP)
+#define bfin_write_USB_EP_NI0_TXMAXP(val)	bfin_write16(USB_EP_NI0_TXMAXP, val)
+#define bfin_read_USB_EP_NI0_TXCSR()		bfin_read16(USB_EP_NI0_TXCSR)
+#define bfin_write_USB_EP_NI0_TXCSR(val)	bfin_write16(USB_EP_NI0_TXCSR, val)
+#define bfin_read_USB_EP_NI0_RXMAXP()		bfin_read16(USB_EP_NI0_RXMAXP)
+#define bfin_write_USB_EP_NI0_RXMAXP(val)	bfin_write16(USB_EP_NI0_RXMAXP, val)
+#define bfin_read_USB_EP_NI0_RXCSR()		bfin_read16(USB_EP_NI0_RXCSR)
+#define bfin_write_USB_EP_NI0_RXCSR(val)	bfin_write16(USB_EP_NI0_RXCSR, val)
+#define bfin_read_USB_EP_NI0_RXCOUNT()		bfin_read16(USB_EP_NI0_RXCOUNT)
+#define bfin_write_USB_EP_NI0_RXCOUNT(val)	bfin_write16(USB_EP_NI0_RXCOUNT, val)
+#define bfin_read_USB_EP_NI0_TXTYPE()		bfin_read16(USB_EP_NI0_TXTYPE)
+#define bfin_write_USB_EP_NI0_TXTYPE(val)	bfin_write16(USB_EP_NI0_TXTYPE, val)
+#define bfin_read_USB_EP_NI0_TXINTERVAL()	bfin_read16(USB_EP_NI0_TXINTERVAL)
+#define bfin_write_USB_EP_NI0_TXINTERVAL(val)	bfin_write16(USB_EP_NI0_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI0_RXTYPE()		bfin_read16(USB_EP_NI0_RXTYPE)
+#define bfin_write_USB_EP_NI0_RXTYPE(val)	bfin_write16(USB_EP_NI0_RXTYPE, val)
+#define bfin_read_USB_EP_NI0_RXINTERVAL()	bfin_read16(USB_EP_NI0_RXINTERVAL)
+#define bfin_write_USB_EP_NI0_RXINTERVAL(val)	bfin_write16(USB_EP_NI0_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI0_TXCOUNT()		bfin_read16(USB_EP_NI0_TXCOUNT)
+#define bfin_write_USB_EP_NI0_TXCOUNT(val)	bfin_write16(USB_EP_NI0_TXCOUNT, val)
+
+/* USB Endpoint 1 Control Registers */
+
+#define bfin_read_USB_EP_NI1_TXMAXP()		bfin_read16(USB_EP_NI1_TXMAXP)
+#define bfin_write_USB_EP_NI1_TXMAXP(val)	bfin_write16(USB_EP_NI1_TXMAXP, val)
+#define bfin_read_USB_EP_NI1_TXCSR()		bfin_read16(USB_EP_NI1_TXCSR)
+#define bfin_write_USB_EP_NI1_TXCSR(val)	bfin_write16(USB_EP_NI1_TXCSR, val)
+#define bfin_read_USB_EP_NI1_RXMAXP()		bfin_read16(USB_EP_NI1_RXMAXP)
+#define bfin_write_USB_EP_NI1_RXMAXP(val)	bfin_write16(USB_EP_NI1_RXMAXP, val)
+#define bfin_read_USB_EP_NI1_RXCSR()		bfin_read16(USB_EP_NI1_RXCSR)
+#define bfin_write_USB_EP_NI1_RXCSR(val)	bfin_write16(USB_EP_NI1_RXCSR, val)
+#define bfin_read_USB_EP_NI1_RXCOUNT()		bfin_read16(USB_EP_NI1_RXCOUNT)
+#define bfin_write_USB_EP_NI1_RXCOUNT(val)	bfin_write16(USB_EP_NI1_RXCOUNT, val)
+#define bfin_read_USB_EP_NI1_TXTYPE()		bfin_read16(USB_EP_NI1_TXTYPE)
+#define bfin_write_USB_EP_NI1_TXTYPE(val)	bfin_write16(USB_EP_NI1_TXTYPE, val)
+#define bfin_read_USB_EP_NI1_TXINTERVAL()	bfin_read16(USB_EP_NI1_TXINTERVAL)
+#define bfin_write_USB_EP_NI1_TXINTERVAL(val)	bfin_write16(USB_EP_NI1_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI1_RXTYPE()		bfin_read16(USB_EP_NI1_RXTYPE)
+#define bfin_write_USB_EP_NI1_RXTYPE(val)	bfin_write16(USB_EP_NI1_RXTYPE, val)
+#define bfin_read_USB_EP_NI1_RXINTERVAL()	bfin_read16(USB_EP_NI1_RXINTERVAL)
+#define bfin_write_USB_EP_NI1_RXINTERVAL(val)	bfin_write16(USB_EP_NI1_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI1_TXCOUNT()		bfin_read16(USB_EP_NI1_TXCOUNT)
+#define bfin_write_USB_EP_NI1_TXCOUNT(val)	bfin_write16(USB_EP_NI1_TXCOUNT, val)
+
+/* USB Endpoint 2 Control Registers */
+
+#define bfin_read_USB_EP_NI2_TXMAXP()		bfin_read16(USB_EP_NI2_TXMAXP)
+#define bfin_write_USB_EP_NI2_TXMAXP(val)	bfin_write16(USB_EP_NI2_TXMAXP, val)
+#define bfin_read_USB_EP_NI2_TXCSR()		bfin_read16(USB_EP_NI2_TXCSR)
+#define bfin_write_USB_EP_NI2_TXCSR(val)	bfin_write16(USB_EP_NI2_TXCSR, val)
+#define bfin_read_USB_EP_NI2_RXMAXP()		bfin_read16(USB_EP_NI2_RXMAXP)
+#define bfin_write_USB_EP_NI2_RXMAXP(val)	bfin_write16(USB_EP_NI2_RXMAXP, val)
+#define bfin_read_USB_EP_NI2_RXCSR()		bfin_read16(USB_EP_NI2_RXCSR)
+#define bfin_write_USB_EP_NI2_RXCSR(val)	bfin_write16(USB_EP_NI2_RXCSR, val)
+#define bfin_read_USB_EP_NI2_RXCOUNT()		bfin_read16(USB_EP_NI2_RXCOUNT)
+#define bfin_write_USB_EP_NI2_RXCOUNT(val)	bfin_write16(USB_EP_NI2_RXCOUNT, val)
+#define bfin_read_USB_EP_NI2_TXTYPE()		bfin_read16(USB_EP_NI2_TXTYPE)
+#define bfin_write_USB_EP_NI2_TXTYPE(val)	bfin_write16(USB_EP_NI2_TXTYPE, val)
+#define bfin_read_USB_EP_NI2_TXINTERVAL()	bfin_read16(USB_EP_NI2_TXINTERVAL)
+#define bfin_write_USB_EP_NI2_TXINTERVAL(val)	bfin_write16(USB_EP_NI2_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI2_RXTYPE()		bfin_read16(USB_EP_NI2_RXTYPE)
+#define bfin_write_USB_EP_NI2_RXTYPE(val)	bfin_write16(USB_EP_NI2_RXTYPE, val)
+#define bfin_read_USB_EP_NI2_RXINTERVAL()	bfin_read16(USB_EP_NI2_RXINTERVAL)
+#define bfin_write_USB_EP_NI2_RXINTERVAL(val)	bfin_write16(USB_EP_NI2_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI2_TXCOUNT()		bfin_read16(USB_EP_NI2_TXCOUNT)
+#define bfin_write_USB_EP_NI2_TXCOUNT(val)	bfin_write16(USB_EP_NI2_TXCOUNT, val)
+
+/* USB Endpoint 3 Control Registers */
+
+#define bfin_read_USB_EP_NI3_TXMAXP()		bfin_read16(USB_EP_NI3_TXMAXP)
+#define bfin_write_USB_EP_NI3_TXMAXP(val)	bfin_write16(USB_EP_NI3_TXMAXP, val)
+#define bfin_read_USB_EP_NI3_TXCSR()		bfin_read16(USB_EP_NI3_TXCSR)
+#define bfin_write_USB_EP_NI3_TXCSR(val)	bfin_write16(USB_EP_NI3_TXCSR, val)
+#define bfin_read_USB_EP_NI3_RXMAXP()		bfin_read16(USB_EP_NI3_RXMAXP)
+#define bfin_write_USB_EP_NI3_RXMAXP(val)	bfin_write16(USB_EP_NI3_RXMAXP, val)
+#define bfin_read_USB_EP_NI3_RXCSR()		bfin_read16(USB_EP_NI3_RXCSR)
+#define bfin_write_USB_EP_NI3_RXCSR(val)	bfin_write16(USB_EP_NI3_RXCSR, val)
+#define bfin_read_USB_EP_NI3_RXCOUNT()		bfin_read16(USB_EP_NI3_RXCOUNT)
+#define bfin_write_USB_EP_NI3_RXCOUNT(val)	bfin_write16(USB_EP_NI3_RXCOUNT, val)
+#define bfin_read_USB_EP_NI3_TXTYPE()		bfin_read16(USB_EP_NI3_TXTYPE)
+#define bfin_write_USB_EP_NI3_TXTYPE(val)	bfin_write16(USB_EP_NI3_TXTYPE, val)
+#define bfin_read_USB_EP_NI3_TXINTERVAL()	bfin_read16(USB_EP_NI3_TXINTERVAL)
+#define bfin_write_USB_EP_NI3_TXINTERVAL(val)	bfin_write16(USB_EP_NI3_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI3_RXTYPE()		bfin_read16(USB_EP_NI3_RXTYPE)
+#define bfin_write_USB_EP_NI3_RXTYPE(val)	bfin_write16(USB_EP_NI3_RXTYPE, val)
+#define bfin_read_USB_EP_NI3_RXINTERVAL()	bfin_read16(USB_EP_NI3_RXINTERVAL)
+#define bfin_write_USB_EP_NI3_RXINTERVAL(val)	bfin_write16(USB_EP_NI3_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI3_TXCOUNT()		bfin_read16(USB_EP_NI3_TXCOUNT)
+#define bfin_write_USB_EP_NI3_TXCOUNT(val)	bfin_write16(USB_EP_NI3_TXCOUNT, val)
+
+/* USB Endpoint 4 Control Registers */
+
+#define bfin_read_USB_EP_NI4_TXMAXP()		bfin_read16(USB_EP_NI4_TXMAXP)
+#define bfin_write_USB_EP_NI4_TXMAXP(val)	bfin_write16(USB_EP_NI4_TXMAXP, val)
+#define bfin_read_USB_EP_NI4_TXCSR()		bfin_read16(USB_EP_NI4_TXCSR)
+#define bfin_write_USB_EP_NI4_TXCSR(val)	bfin_write16(USB_EP_NI4_TXCSR, val)
+#define bfin_read_USB_EP_NI4_RXMAXP()		bfin_read16(USB_EP_NI4_RXMAXP)
+#define bfin_write_USB_EP_NI4_RXMAXP(val)	bfin_write16(USB_EP_NI4_RXMAXP, val)
+#define bfin_read_USB_EP_NI4_RXCSR()		bfin_read16(USB_EP_NI4_RXCSR)
+#define bfin_write_USB_EP_NI4_RXCSR(val)	bfin_write16(USB_EP_NI4_RXCSR, val)
+#define bfin_read_USB_EP_NI4_RXCOUNT()		bfin_read16(USB_EP_NI4_RXCOUNT)
+#define bfin_write_USB_EP_NI4_RXCOUNT(val)	bfin_write16(USB_EP_NI4_RXCOUNT, val)
+#define bfin_read_USB_EP_NI4_TXTYPE()		bfin_read16(USB_EP_NI4_TXTYPE)
+#define bfin_write_USB_EP_NI4_TXTYPE(val)	bfin_write16(USB_EP_NI4_TXTYPE, val)
+#define bfin_read_USB_EP_NI4_TXINTERVAL()	bfin_read16(USB_EP_NI4_TXINTERVAL)
+#define bfin_write_USB_EP_NI4_TXINTERVAL(val)	bfin_write16(USB_EP_NI4_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI4_RXTYPE()		bfin_read16(USB_EP_NI4_RXTYPE)
+#define bfin_write_USB_EP_NI4_RXTYPE(val)	bfin_write16(USB_EP_NI4_RXTYPE, val)
+#define bfin_read_USB_EP_NI4_RXINTERVAL()	bfin_read16(USB_EP_NI4_RXINTERVAL)
+#define bfin_write_USB_EP_NI4_RXINTERVAL(val)	bfin_write16(USB_EP_NI4_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI4_TXCOUNT()		bfin_read16(USB_EP_NI4_TXCOUNT)
+#define bfin_write_USB_EP_NI4_TXCOUNT(val)	bfin_write16(USB_EP_NI4_TXCOUNT, val)
+
+/* USB Endpoint 5 Control Registers */
+
+#define bfin_read_USB_EP_NI5_TXMAXP()		bfin_read16(USB_EP_NI5_TXMAXP)
+#define bfin_write_USB_EP_NI5_TXMAXP(val)	bfin_write16(USB_EP_NI5_TXMAXP, val)
+#define bfin_read_USB_EP_NI5_TXCSR()		bfin_read16(USB_EP_NI5_TXCSR)
+#define bfin_write_USB_EP_NI5_TXCSR(val)	bfin_write16(USB_EP_NI5_TXCSR, val)
+#define bfin_read_USB_EP_NI5_RXMAXP()		bfin_read16(USB_EP_NI5_RXMAXP)
+#define bfin_write_USB_EP_NI5_RXMAXP(val)	bfin_write16(USB_EP_NI5_RXMAXP, val)
+#define bfin_read_USB_EP_NI5_RXCSR()		bfin_read16(USB_EP_NI5_RXCSR)
+#define bfin_write_USB_EP_NI5_RXCSR(val)	bfin_write16(USB_EP_NI5_RXCSR, val)
+#define bfin_read_USB_EP_NI5_RXCOUNT()		bfin_read16(USB_EP_NI5_RXCOUNT)
+#define bfin_write_USB_EP_NI5_RXCOUNT(val)	bfin_write16(USB_EP_NI5_RXCOUNT, val)
+#define bfin_read_USB_EP_NI5_TXTYPE()		bfin_read16(USB_EP_NI5_TXTYPE)
+#define bfin_write_USB_EP_NI5_TXTYPE(val)	bfin_write16(USB_EP_NI5_TXTYPE, val)
+#define bfin_read_USB_EP_NI5_TXINTERVAL()	bfin_read16(USB_EP_NI5_TXINTERVAL)
+#define bfin_write_USB_EP_NI5_TXINTERVAL(val)	bfin_write16(USB_EP_NI5_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI5_RXTYPE()		bfin_read16(USB_EP_NI5_RXTYPE)
+#define bfin_write_USB_EP_NI5_RXTYPE(val)	bfin_write16(USB_EP_NI5_RXTYPE, val)
+#define bfin_read_USB_EP_NI5_RXINTERVAL()	bfin_read16(USB_EP_NI5_RXINTERVAL)
+#define bfin_write_USB_EP_NI5_RXINTERVAL(val)	bfin_write16(USB_EP_NI5_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI5_TXCOUNT()		bfin_read16(USB_EP_NI5_TXCOUNT)
+#define bfin_write_USB_EP_NI5_TXCOUNT(val)	bfin_write16(USB_EP_NI5_TXCOUNT, val)
+
+/* USB Endpoint 6 Control Registers */
+
+#define bfin_read_USB_EP_NI6_TXMAXP()		bfin_read16(USB_EP_NI6_TXMAXP)
+#define bfin_write_USB_EP_NI6_TXMAXP(val)	bfin_write16(USB_EP_NI6_TXMAXP, val)
+#define bfin_read_USB_EP_NI6_TXCSR()		bfin_read16(USB_EP_NI6_TXCSR)
+#define bfin_write_USB_EP_NI6_TXCSR(val)	bfin_write16(USB_EP_NI6_TXCSR, val)
+#define bfin_read_USB_EP_NI6_RXMAXP()		bfin_read16(USB_EP_NI6_RXMAXP)
+#define bfin_write_USB_EP_NI6_RXMAXP(val)	bfin_write16(USB_EP_NI6_RXMAXP, val)
+#define bfin_read_USB_EP_NI6_RXCSR()		bfin_read16(USB_EP_NI6_RXCSR)
+#define bfin_write_USB_EP_NI6_RXCSR(val)	bfin_write16(USB_EP_NI6_RXCSR, val)
+#define bfin_read_USB_EP_NI6_RXCOUNT()		bfin_read16(USB_EP_NI6_RXCOUNT)
+#define bfin_write_USB_EP_NI6_RXCOUNT(val)	bfin_write16(USB_EP_NI6_RXCOUNT, val)
+#define bfin_read_USB_EP_NI6_TXTYPE()		bfin_read16(USB_EP_NI6_TXTYPE)
+#define bfin_write_USB_EP_NI6_TXTYPE(val)	bfin_write16(USB_EP_NI6_TXTYPE, val)
+#define bfin_read_USB_EP_NI6_TXINTERVAL()	bfin_read16(USB_EP_NI6_TXINTERVAL)
+#define bfin_write_USB_EP_NI6_TXINTERVAL(val)	bfin_write16(USB_EP_NI6_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI6_RXTYPE()		bfin_read16(USB_EP_NI6_RXTYPE)
+#define bfin_write_USB_EP_NI6_RXTYPE(val)	bfin_write16(USB_EP_NI6_RXTYPE, val)
+#define bfin_read_USB_EP_NI6_RXINTERVAL()	bfin_read16(USB_EP_NI6_RXINTERVAL)
+#define bfin_write_USB_EP_NI6_RXINTERVAL(val)	bfin_write16(USB_EP_NI6_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI6_TXCOUNT()		bfin_read16(USB_EP_NI6_TXCOUNT)
+#define bfin_write_USB_EP_NI6_TXCOUNT(val)	bfin_write16(USB_EP_NI6_TXCOUNT, val)
+
+/* USB Endpoint 7 Control Registers */
+
+#define bfin_read_USB_EP_NI7_TXMAXP()		bfin_read16(USB_EP_NI7_TXMAXP)
+#define bfin_write_USB_EP_NI7_TXMAXP(val)	bfin_write16(USB_EP_NI7_TXMAXP, val)
+#define bfin_read_USB_EP_NI7_TXCSR()		bfin_read16(USB_EP_NI7_TXCSR)
+#define bfin_write_USB_EP_NI7_TXCSR(val)	bfin_write16(USB_EP_NI7_TXCSR, val)
+#define bfin_read_USB_EP_NI7_RXMAXP()		bfin_read16(USB_EP_NI7_RXMAXP)
+#define bfin_write_USB_EP_NI7_RXMAXP(val)	bfin_write16(USB_EP_NI7_RXMAXP, val)
+#define bfin_read_USB_EP_NI7_RXCSR()		bfin_read16(USB_EP_NI7_RXCSR)
+#define bfin_write_USB_EP_NI7_RXCSR(val)	bfin_write16(USB_EP_NI7_RXCSR, val)
+#define bfin_read_USB_EP_NI7_RXCOUNT()		bfin_read16(USB_EP_NI7_RXCOUNT)
+#define bfin_write_USB_EP_NI7_RXCOUNT(val)	bfin_write16(USB_EP_NI7_RXCOUNT, val)
+#define bfin_read_USB_EP_NI7_TXTYPE()		bfin_read16(USB_EP_NI7_TXTYPE)
+#define bfin_write_USB_EP_NI7_TXTYPE(val)	bfin_write16(USB_EP_NI7_TXTYPE, val)
+#define bfin_read_USB_EP_NI7_TXINTERVAL()	bfin_read16(USB_EP_NI7_TXINTERVAL)
+#define bfin_write_USB_EP_NI7_TXINTERVAL(val)	bfin_write16(USB_EP_NI7_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI7_RXTYPE()		bfin_read16(USB_EP_NI7_RXTYPE)
+#define bfin_write_USB_EP_NI7_RXTYPE(val)	bfin_write16(USB_EP_NI7_RXTYPE, val)
+#define bfin_read_USB_EP_NI7_RXINTERVAL()	bfin_read16(USB_EP_NI7_RXINTERVAL)
+#define bfin_write_USB_EP_NI7_RXINTERVAL(val)	bfin_write16(USB_EP_NI7_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI7_TXCOUNT()		bfin_read16(USB_EP_NI7_TXCOUNT)
+#define bfin_write_USB_EP_NI7_TXCOUNT(val)	bfin_write16(USB_EP_NI7_TXCOUNT, val)
+
+#define bfin_read_USB_DMA_INTERRUPT()		bfin_read16(USB_DMA_INTERRUPT)
+#define bfin_write_USB_DMA_INTERRUPT(val)	bfin_write16(USB_DMA_INTERRUPT, val)
+
+/* USB Channel 0 Config Registers */
+
+#define bfin_read_USB_DMA0CONTROL()		bfin_read16(USB_DMA0CONTROL)
+#define bfin_write_USB_DMA0CONTROL(val)		bfin_write16(USB_DMA0CONTROL, val)
+#define bfin_read_USB_DMA0ADDRLOW()		bfin_read16(USB_DMA0ADDRLOW)
+#define bfin_write_USB_DMA0ADDRLOW(val)		bfin_write16(USB_DMA0ADDRLOW, val)
+#define bfin_read_USB_DMA0ADDRHIGH()		bfin_read16(USB_DMA0ADDRHIGH)
+#define bfin_write_USB_DMA0ADDRHIGH(val)	bfin_write16(USB_DMA0ADDRHIGH, val)
+#define bfin_read_USB_DMA0COUNTLOW()		bfin_read16(USB_DMA0COUNTLOW)
+#define bfin_write_USB_DMA0COUNTLOW(val)	bfin_write16(USB_DMA0COUNTLOW, val)
+#define bfin_read_USB_DMA0COUNTHIGH()		bfin_read16(USB_DMA0COUNTHIGH)
+#define bfin_write_USB_DMA0COUNTHIGH(val)	bfin_write16(USB_DMA0COUNTHIGH, val)
+
+/* USB Channel 1 Config Registers */
+
+#define bfin_read_USB_DMA1CONTROL()		bfin_read16(USB_DMA1CONTROL)
+#define bfin_write_USB_DMA1CONTROL(val)		bfin_write16(USB_DMA1CONTROL, val)
+#define bfin_read_USB_DMA1ADDRLOW()		bfin_read16(USB_DMA1ADDRLOW)
+#define bfin_write_USB_DMA1ADDRLOW(val)		bfin_write16(USB_DMA1ADDRLOW, val)
+#define bfin_read_USB_DMA1ADDRHIGH()		bfin_read16(USB_DMA1ADDRHIGH)
+#define bfin_write_USB_DMA1ADDRHIGH(val)	bfin_write16(USB_DMA1ADDRHIGH, val)
+#define bfin_read_USB_DMA1COUNTLOW()		bfin_read16(USB_DMA1COUNTLOW)
+#define bfin_write_USB_DMA1COUNTLOW(val)	bfin_write16(USB_DMA1COUNTLOW, val)
+#define bfin_read_USB_DMA1COUNTHIGH()		bfin_read16(USB_DMA1COUNTHIGH)
+#define bfin_write_USB_DMA1COUNTHIGH(val)	bfin_write16(USB_DMA1COUNTHIGH, val)
+
+/* USB Channel 2 Config Registers */
+
+#define bfin_read_USB_DMA2CONTROL()		bfin_read16(USB_DMA2CONTROL)
+#define bfin_write_USB_DMA2CONTROL(val)		bfin_write16(USB_DMA2CONTROL, val)
+#define bfin_read_USB_DMA2ADDRLOW()		bfin_read16(USB_DMA2ADDRLOW)
+#define bfin_write_USB_DMA2ADDRLOW(val)		bfin_write16(USB_DMA2ADDRLOW, val)
+#define bfin_read_USB_DMA2ADDRHIGH()		bfin_read16(USB_DMA2ADDRHIGH)
+#define bfin_write_USB_DMA2ADDRHIGH(val)	bfin_write16(USB_DMA2ADDRHIGH, val)
+#define bfin_read_USB_DMA2COUNTLOW()		bfin_read16(USB_DMA2COUNTLOW)
+#define bfin_write_USB_DMA2COUNTLOW(val)	bfin_write16(USB_DMA2COUNTLOW, val)
+#define bfin_read_USB_DMA2COUNTHIGH()		bfin_read16(USB_DMA2COUNTHIGH)
+#define bfin_write_USB_DMA2COUNTHIGH(val)	bfin_write16(USB_DMA2COUNTHIGH, val)
+
+/* USB Channel 3 Config Registers */
+
+#define bfin_read_USB_DMA3CONTROL()		bfin_read16(USB_DMA3CONTROL)
+#define bfin_write_USB_DMA3CONTROL(val)		bfin_write16(USB_DMA3CONTROL, val)
+#define bfin_read_USB_DMA3ADDRLOW()		bfin_read16(USB_DMA3ADDRLOW)
+#define bfin_write_USB_DMA3ADDRLOW(val)		bfin_write16(USB_DMA3ADDRLOW, val)
+#define bfin_read_USB_DMA3ADDRHIGH()		bfin_read16(USB_DMA3ADDRHIGH)
+#define bfin_write_USB_DMA3ADDRHIGH(val)	bfin_write16(USB_DMA3ADDRHIGH, val)
+#define bfin_read_USB_DMA3COUNTLOW()		bfin_read16(USB_DMA3COUNTLOW)
+#define bfin_write_USB_DMA3COUNTLOW(val)	bfin_write16(USB_DMA3COUNTLOW, val)
+#define bfin_read_USB_DMA3COUNTHIGH()		bfin_read16(USB_DMA3COUNTHIGH)
+#define bfin_write_USB_DMA3COUNTHIGH(val)	bfin_write16(USB_DMA3COUNTHIGH, val)
+
+/* USB Channel 4 Config Registers */
+
+#define bfin_read_USB_DMA4CONTROL()		bfin_read16(USB_DMA4CONTROL)
+#define bfin_write_USB_DMA4CONTROL(val)		bfin_write16(USB_DMA4CONTROL, val)
+#define bfin_read_USB_DMA4ADDRLOW()		bfin_read16(USB_DMA4ADDRLOW)
+#define bfin_write_USB_DMA4ADDRLOW(val)		bfin_write16(USB_DMA4ADDRLOW, val)
+#define bfin_read_USB_DMA4ADDRHIGH()		bfin_read16(USB_DMA4ADDRHIGH)
+#define bfin_write_USB_DMA4ADDRHIGH(val)	bfin_write16(USB_DMA4ADDRHIGH, val)
+#define bfin_read_USB_DMA4COUNTLOW()		bfin_read16(USB_DMA4COUNTLOW)
+#define bfin_write_USB_DMA4COUNTLOW(val)	bfin_write16(USB_DMA4COUNTLOW, val)
+#define bfin_read_USB_DMA4COUNTHIGH()		bfin_read16(USB_DMA4COUNTHIGH)
+#define bfin_write_USB_DMA4COUNTHIGH(val)	bfin_write16(USB_DMA4COUNTHIGH, val)
+
+/* USB Channel 5 Config Registers */
+
+#define bfin_read_USB_DMA5CONTROL()		bfin_read16(USB_DMA5CONTROL)
+#define bfin_write_USB_DMA5CONTROL(val)		bfin_write16(USB_DMA5CONTROL, val)
+#define bfin_read_USB_DMA5ADDRLOW()		bfin_read16(USB_DMA5ADDRLOW)
+#define bfin_write_USB_DMA5ADDRLOW(val)		bfin_write16(USB_DMA5ADDRLOW, val)
+#define bfin_read_USB_DMA5ADDRHIGH()		bfin_read16(USB_DMA5ADDRHIGH)
+#define bfin_write_USB_DMA5ADDRHIGH(val)	bfin_write16(USB_DMA5ADDRHIGH, val)
+#define bfin_read_USB_DMA5COUNTLOW()		bfin_read16(USB_DMA5COUNTLOW)
+#define bfin_write_USB_DMA5COUNTLOW(val)	bfin_write16(USB_DMA5COUNTLOW, val)
+#define bfin_read_USB_DMA5COUNTHIGH()		bfin_read16(USB_DMA5COUNTHIGH)
+#define bfin_write_USB_DMA5COUNTHIGH(val)	bfin_write16(USB_DMA5COUNTHIGH, val)
+
+/* USB Channel 6 Config Registers */
+
+#define bfin_read_USB_DMA6CONTROL()		bfin_read16(USB_DMA6CONTROL)
+#define bfin_write_USB_DMA6CONTROL(val)		bfin_write16(USB_DMA6CONTROL, val)
+#define bfin_read_USB_DMA6ADDRLOW()		bfin_read16(USB_DMA6ADDRLOW)
+#define bfin_write_USB_DMA6ADDRLOW(val)		bfin_write16(USB_DMA6ADDRLOW, val)
+#define bfin_read_USB_DMA6ADDRHIGH()		bfin_read16(USB_DMA6ADDRHIGH)
+#define bfin_write_USB_DMA6ADDRHIGH(val)	bfin_write16(USB_DMA6ADDRHIGH, val)
+#define bfin_read_USB_DMA6COUNTLOW()		bfin_read16(USB_DMA6COUNTLOW)
+#define bfin_write_USB_DMA6COUNTLOW(val)	bfin_write16(USB_DMA6COUNTLOW, val)
+#define bfin_read_USB_DMA6COUNTHIGH()		bfin_read16(USB_DMA6COUNTHIGH)
+#define bfin_write_USB_DMA6COUNTHIGH(val)	bfin_write16(USB_DMA6COUNTHIGH, val)
+
+/* USB Channel 7 Config Registers */
+
+#define bfin_read_USB_DMA7CONTROL()		bfin_read16(USB_DMA7CONTROL)
+#define bfin_write_USB_DMA7CONTROL(val)		bfin_write16(USB_DMA7CONTROL, val)
+#define bfin_read_USB_DMA7ADDRLOW()		bfin_read16(USB_DMA7ADDRLOW)
+#define bfin_write_USB_DMA7ADDRLOW(val)		bfin_write16(USB_DMA7ADDRLOW, val)
+#define bfin_read_USB_DMA7ADDRHIGH()		bfin_read16(USB_DMA7ADDRHIGH)
+#define bfin_write_USB_DMA7ADDRHIGH(val)	bfin_write16(USB_DMA7ADDRHIGH, val)
+#define bfin_read_USB_DMA7COUNTLOW()		bfin_read16(USB_DMA7COUNTLOW)
+#define bfin_write_USB_DMA7COUNTLOW(val)	bfin_write16(USB_DMA7COUNTLOW, val)
+#define bfin_read_USB_DMA7COUNTHIGH()		bfin_read16(USB_DMA7COUNTHIGH)
+#define bfin_write_USB_DMA7COUNTHIGH(val)	bfin_write16(USB_DMA7COUNTHIGH, val)
+
+#endif /* _CDEF_BF525_H */
diff --git a/arch/blackfin/mach-bf527/include/mach/cdefBF527.h b/arch/blackfin/mach-bf527/include/mach/cdefBF527.h
new file mode 100644
index 00000000000..fca8db70811
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/cdefBF527.h
@@ -0,0 +1,626 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/cdefbf527.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:  system mmr register map
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _CDEF_BF527_H
+#define _CDEF_BF527_H
+
+/* include all Core registers and bit definitions */
+#include "defBF527.h"
+
+/* include core specific register pointer definitions */
+#include <asm/cdef_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF527 */
+
+/* include cdefBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */
+#include "cdefBF52x_base.h"
+
+/* The following are the #defines needed by ADSP-BF527 that are not in the common header */
+
+/* 10/100 Ethernet Controller	(0xFFC03000 - 0xFFC031FF) */
+
+#define bfin_read_EMAC_OPMODE()			bfin_read32(EMAC_OPMODE)
+#define bfin_write_EMAC_OPMODE(val)		bfin_write32(EMAC_OPMODE, val)
+#define bfin_read_EMAC_ADDRLO()			bfin_read32(EMAC_ADDRLO)
+#define bfin_write_EMAC_ADDRLO(val)		bfin_write32(EMAC_ADDRLO, val)
+#define bfin_read_EMAC_ADDRHI()			bfin_read32(EMAC_ADDRHI)
+#define bfin_write_EMAC_ADDRHI(val)		bfin_write32(EMAC_ADDRHI, val)
+#define bfin_read_EMAC_HASHLO()			bfin_read32(EMAC_HASHLO)
+#define bfin_write_EMAC_HASHLO(val)		bfin_write32(EMAC_HASHLO, val)
+#define bfin_read_EMAC_HASHHI()			bfin_read32(EMAC_HASHHI)
+#define bfin_write_EMAC_HASHHI(val)		bfin_write32(EMAC_HASHHI, val)
+#define bfin_read_EMAC_STAADD()			bfin_read32(EMAC_STAADD)
+#define bfin_write_EMAC_STAADD(val)		bfin_write32(EMAC_STAADD, val)
+#define bfin_read_EMAC_STADAT()			bfin_read32(EMAC_STADAT)
+#define bfin_write_EMAC_STADAT(val)		bfin_write32(EMAC_STADAT, val)
+#define bfin_read_EMAC_FLC()			bfin_read32(EMAC_FLC)
+#define bfin_write_EMAC_FLC(val)		bfin_write32(EMAC_FLC, val)
+#define bfin_read_EMAC_VLAN1()			bfin_read32(EMAC_VLAN1)
+#define bfin_write_EMAC_VLAN1(val)		bfin_write32(EMAC_VLAN1, val)
+#define bfin_read_EMAC_VLAN2()			bfin_read32(EMAC_VLAN2)
+#define bfin_write_EMAC_VLAN2(val)		bfin_write32(EMAC_VLAN2, val)
+#define bfin_read_EMAC_WKUP_CTL()		bfin_read32(EMAC_WKUP_CTL)
+#define bfin_write_EMAC_WKUP_CTL(val)		bfin_write32(EMAC_WKUP_CTL, val)
+#define bfin_read_EMAC_WKUP_FFMSK0()		bfin_read32(EMAC_WKUP_FFMSK0)
+#define bfin_write_EMAC_WKUP_FFMSK0(val)	bfin_write32(EMAC_WKUP_FFMSK0, val)
+#define bfin_read_EMAC_WKUP_FFMSK1()		bfin_read32(EMAC_WKUP_FFMSK1)
+#define bfin_write_EMAC_WKUP_FFMSK1(val)	bfin_write32(EMAC_WKUP_FFMSK1, val)
+#define bfin_read_EMAC_WKUP_FFMSK2()		bfin_read32(EMAC_WKUP_FFMSK2)
+#define bfin_write_EMAC_WKUP_FFMSK2(val)	bfin_write32(EMAC_WKUP_FFMSK2, val)
+#define bfin_read_EMAC_WKUP_FFMSK3()		bfin_read32(EMAC_WKUP_FFMSK3)
+#define bfin_write_EMAC_WKUP_FFMSK3(val)	bfin_write32(EMAC_WKUP_FFMSK3, val)
+#define bfin_read_EMAC_WKUP_FFCMD()		bfin_read32(EMAC_WKUP_FFCMD)
+#define bfin_write_EMAC_WKUP_FFCMD(val)		bfin_write32(EMAC_WKUP_FFCMD, val)
+#define bfin_read_EMAC_WKUP_FFOFF()		bfin_read32(EMAC_WKUP_FFOFF)
+#define bfin_write_EMAC_WKUP_FFOFF(val)		bfin_write32(EMAC_WKUP_FFOFF, val)
+#define bfin_read_EMAC_WKUP_FFCRC0()		bfin_read32(EMAC_WKUP_FFCRC0)
+#define bfin_write_EMAC_WKUP_FFCRC0(val)	bfin_write32(EMAC_WKUP_FFCRC0, val)
+#define bfin_read_EMAC_WKUP_FFCRC1()		bfin_read32(EMAC_WKUP_FFCRC1)
+#define bfin_write_EMAC_WKUP_FFCRC1(val)	bfin_write32(EMAC_WKUP_FFCRC1, val)
+
+#define bfin_read_EMAC_SYSCTL()			bfin_read32(EMAC_SYSCTL)
+#define bfin_write_EMAC_SYSCTL(val)		bfin_write32(EMAC_SYSCTL, val)
+#define bfin_read_EMAC_SYSTAT()			bfin_read32(EMAC_SYSTAT)
+#define bfin_write_EMAC_SYSTAT(val)		bfin_write32(EMAC_SYSTAT, val)
+#define bfin_read_EMAC_RX_STAT()		bfin_read32(EMAC_RX_STAT)
+#define bfin_write_EMAC_RX_STAT(val)		bfin_write32(EMAC_RX_STAT, val)
+#define bfin_read_EMAC_RX_STKY()		bfin_read32(EMAC_RX_STKY)
+#define bfin_write_EMAC_RX_STKY(val)		bfin_write32(EMAC_RX_STKY, val)
+#define bfin_read_EMAC_RX_IRQE()		bfin_read32(EMAC_RX_IRQE)
+#define bfin_write_EMAC_RX_IRQE(val)		bfin_write32(EMAC_RX_IRQE, val)
+#define bfin_read_EMAC_TX_STAT()		bfin_read32(EMAC_TX_STAT)
+#define bfin_write_EMAC_TX_STAT(val)		bfin_write32(EMAC_TX_STAT, val)
+#define bfin_read_EMAC_TX_STKY()		bfin_read32(EMAC_TX_STKY)
+#define bfin_write_EMAC_TX_STKY(val)		bfin_write32(EMAC_TX_STKY, val)
+#define bfin_read_EMAC_TX_IRQE()		bfin_read32(EMAC_TX_IRQE)
+#define bfin_write_EMAC_TX_IRQE(val)		bfin_write32(EMAC_TX_IRQE, val)
+
+#define bfin_read_EMAC_MMC_CTL()		bfin_read32(EMAC_MMC_CTL)
+#define bfin_write_EMAC_MMC_CTL(val)		bfin_write32(EMAC_MMC_CTL, val)
+#define bfin_read_EMAC_MMC_RIRQS()		bfin_read32(EMAC_MMC_RIRQS)
+#define bfin_write_EMAC_MMC_RIRQS(val)		bfin_write32(EMAC_MMC_RIRQS, val)
+#define bfin_read_EMAC_MMC_RIRQE()		bfin_read32(EMAC_MMC_RIRQE)
+#define bfin_write_EMAC_MMC_RIRQE(val)		bfin_write32(EMAC_MMC_RIRQE, val)
+#define bfin_read_EMAC_MMC_TIRQS()		bfin_read32(EMAC_MMC_TIRQS)
+#define bfin_write_EMAC_MMC_TIRQS(val)		bfin_write32(EMAC_MMC_TIRQS, val)
+#define bfin_read_EMAC_MMC_TIRQE()		bfin_read32(EMAC_MMC_TIRQE)
+#define bfin_write_EMAC_MMC_TIRQE(val)		bfin_write32(EMAC_MMC_TIRQE, val)
+
+#define bfin_read_EMAC_RXC_OK()			bfin_read32(EMAC_RXC_OK)
+#define bfin_write_EMAC_RXC_OK(val)		bfin_write32(EMAC_RXC_OK, val)
+#define bfin_read_EMAC_RXC_FCS()		bfin_read32(EMAC_RXC_FCS)
+#define bfin_write_EMAC_RXC_FCS(val)		bfin_write32(EMAC_RXC_FCS, val)
+#define bfin_read_EMAC_RXC_ALIGN()		bfin_read32(EMAC_RXC_ALIGN)
+#define bfin_write_EMAC_RXC_ALIGN(val)		bfin_write32(EMAC_RXC_ALIGN, val)
+#define bfin_read_EMAC_RXC_OCTET()		bfin_read32(EMAC_RXC_OCTET)
+#define bfin_write_EMAC_RXC_OCTET(val)		bfin_write32(EMAC_RXC_OCTET, val)
+#define bfin_read_EMAC_RXC_DMAOVF()		bfin_read32(EMAC_RXC_DMAOVF)
+#define bfin_write_EMAC_RXC_DMAOVF(val)		bfin_write32(EMAC_RXC_DMAOVF, val)
+#define bfin_read_EMAC_RXC_UNICST()		bfin_read32(EMAC_RXC_UNICST)
+#define bfin_write_EMAC_RXC_UNICST(val)		bfin_write32(EMAC_RXC_UNICST, val)
+#define bfin_read_EMAC_RXC_MULTI()		bfin_read32(EMAC_RXC_MULTI)
+#define bfin_write_EMAC_RXC_MULTI(val)		bfin_write32(EMAC_RXC_MULTI, val)
+#define bfin_read_EMAC_RXC_BROAD()		bfin_read32(EMAC_RXC_BROAD)
+#define bfin_write_EMAC_RXC_BROAD(val)		bfin_write32(EMAC_RXC_BROAD, val)
+#define bfin_read_EMAC_RXC_LNERRI()		bfin_read32(EMAC_RXC_LNERRI)
+#define bfin_write_EMAC_RXC_LNERRI(val)		bfin_write32(EMAC_RXC_LNERRI, val)
+#define bfin_read_EMAC_RXC_LNERRO()		bfin_read32(EMAC_RXC_LNERRO)
+#define bfin_write_EMAC_RXC_LNERRO(val)		bfin_write32(EMAC_RXC_LNERRO, val)
+#define bfin_read_EMAC_RXC_LONG()		bfin_read32(EMAC_RXC_LONG)
+#define bfin_write_EMAC_RXC_LONG(val)		bfin_write32(EMAC_RXC_LONG, val)
+#define bfin_read_EMAC_RXC_MACCTL()		bfin_read32(EMAC_RXC_MACCTL)
+#define bfin_write_EMAC_RXC_MACCTL(val)		bfin_write32(EMAC_RXC_MACCTL, val)
+#define bfin_read_EMAC_RXC_OPCODE()		bfin_read32(EMAC_RXC_OPCODE)
+#define bfin_write_EMAC_RXC_OPCODE(val)		bfin_write32(EMAC_RXC_OPCODE, val)
+#define bfin_read_EMAC_RXC_PAUSE()		bfin_read32(EMAC_RXC_PAUSE)
+#define bfin_write_EMAC_RXC_PAUSE(val)		bfin_write32(EMAC_RXC_PAUSE, val)
+#define bfin_read_EMAC_RXC_ALLFRM()		bfin_read32(EMAC_RXC_ALLFRM)
+#define bfin_write_EMAC_RXC_ALLFRM(val)		bfin_write32(EMAC_RXC_ALLFRM, val)
+#define bfin_read_EMAC_RXC_ALLOCT()		bfin_read32(EMAC_RXC_ALLOCT)
+#define bfin_write_EMAC_RXC_ALLOCT(val)		bfin_write32(EMAC_RXC_ALLOCT, val)
+#define bfin_read_EMAC_RXC_TYPED()		bfin_read32(EMAC_RXC_TYPED)
+#define bfin_write_EMAC_RXC_TYPED(val)		bfin_write32(EMAC_RXC_TYPED, val)
+#define bfin_read_EMAC_RXC_SHORT()		bfin_read32(EMAC_RXC_SHORT)
+#define bfin_write_EMAC_RXC_SHORT(val)		bfin_write32(EMAC_RXC_SHORT, val)
+#define bfin_read_EMAC_RXC_EQ64()		bfin_read32(EMAC_RXC_EQ64)
+#define bfin_write_EMAC_RXC_EQ64(val)		bfin_write32(EMAC_RXC_EQ64, val)
+#define bfin_read_EMAC_RXC_LT128()		bfin_read32(EMAC_RXC_LT128)
+#define bfin_write_EMAC_RXC_LT128(val)		bfin_write32(EMAC_RXC_LT128, val)
+#define bfin_read_EMAC_RXC_LT256()		bfin_read32(EMAC_RXC_LT256)
+#define bfin_write_EMAC_RXC_LT256(val)		bfin_write32(EMAC_RXC_LT256, val)
+#define bfin_read_EMAC_RXC_LT512()		bfin_read32(EMAC_RXC_LT512)
+#define bfin_write_EMAC_RXC_LT512(val)		bfin_write32(EMAC_RXC_LT512, val)
+#define bfin_read_EMAC_RXC_LT1024()		bfin_read32(EMAC_RXC_LT1024)
+#define bfin_write_EMAC_RXC_LT1024(val)		bfin_write32(EMAC_RXC_LT1024, val)
+#define bfin_read_EMAC_RXC_GE1024()		bfin_read32(EMAC_RXC_GE1024)
+#define bfin_write_EMAC_RXC_GE1024(val)		bfin_write32(EMAC_RXC_GE1024, val)
+
+#define bfin_read_EMAC_TXC_OK()			bfin_read32(EMAC_TXC_OK)
+#define bfin_write_EMAC_TXC_OK(val)		bfin_write32(EMAC_TXC_OK, val)
+#define bfin_read_EMAC_TXC_1COL()		bfin_read32(EMAC_TXC_1COL)
+#define bfin_write_EMAC_TXC_1COL(val)		bfin_write32(EMAC_TXC_1COL, val)
+#define bfin_read_EMAC_TXC_GT1COL()		bfin_read32(EMAC_TXC_GT1COL)
+#define bfin_write_EMAC_TXC_GT1COL(val)		bfin_write32(EMAC_TXC_GT1COL, val)
+#define bfin_read_EMAC_TXC_OCTET()		bfin_read32(EMAC_TXC_OCTET)
+#define bfin_write_EMAC_TXC_OCTET(val)		bfin_write32(EMAC_TXC_OCTET, val)
+#define bfin_read_EMAC_TXC_DEFER()		bfin_read32(EMAC_TXC_DEFER)
+#define bfin_write_EMAC_TXC_DEFER(val)		bfin_write32(EMAC_TXC_DEFER, val)
+#define bfin_read_EMAC_TXC_LATECL()		bfin_read32(EMAC_TXC_LATECL)
+#define bfin_write_EMAC_TXC_LATECL(val)		bfin_write32(EMAC_TXC_LATECL, val)
+#define bfin_read_EMAC_TXC_XS_COL()		bfin_read32(EMAC_TXC_XS_COL)
+#define bfin_write_EMAC_TXC_XS_COL(val)		bfin_write32(EMAC_TXC_XS_COL, val)
+#define bfin_read_EMAC_TXC_DMAUND()		bfin_read32(EMAC_TXC_DMAUND)
+#define bfin_write_EMAC_TXC_DMAUND(val)		bfin_write32(EMAC_TXC_DMAUND, val)
+#define bfin_read_EMAC_TXC_CRSERR()		bfin_read32(EMAC_TXC_CRSERR)
+#define bfin_write_EMAC_TXC_CRSERR(val)		bfin_write32(EMAC_TXC_CRSERR, val)
+#define bfin_read_EMAC_TXC_UNICST()		bfin_read32(EMAC_TXC_UNICST)
+#define bfin_write_EMAC_TXC_UNICST(val)		bfin_write32(EMAC_TXC_UNICST, val)
+#define bfin_read_EMAC_TXC_MULTI()		bfin_read32(EMAC_TXC_MULTI)
+#define bfin_write_EMAC_TXC_MULTI(val)		bfin_write32(EMAC_TXC_MULTI, val)
+#define bfin_read_EMAC_TXC_BROAD()		bfin_read32(EMAC_TXC_BROAD)
+#define bfin_write_EMAC_TXC_BROAD(val)		bfin_write32(EMAC_TXC_BROAD, val)
+#define bfin_read_EMAC_TXC_XS_DFR()		bfin_read32(EMAC_TXC_XS_DFR)
+#define bfin_write_EMAC_TXC_XS_DFR(val)		bfin_write32(EMAC_TXC_XS_DFR, val)
+#define bfin_read_EMAC_TXC_MACCTL()		bfin_read32(EMAC_TXC_MACCTL)
+#define bfin_write_EMAC_TXC_MACCTL(val)		bfin_write32(EMAC_TXC_MACCTL, val)
+#define bfin_read_EMAC_TXC_ALLFRM()		bfin_read32(EMAC_TXC_ALLFRM)
+#define bfin_write_EMAC_TXC_ALLFRM(val)		bfin_write32(EMAC_TXC_ALLFRM, val)
+#define bfin_read_EMAC_TXC_ALLOCT()		bfin_read32(EMAC_TXC_ALLOCT)
+#define bfin_write_EMAC_TXC_ALLOCT(val)		bfin_write32(EMAC_TXC_ALLOCT, val)
+#define bfin_read_EMAC_TXC_EQ64()		bfin_read32(EMAC_TXC_EQ64)
+#define bfin_write_EMAC_TXC_EQ64(val)		bfin_write32(EMAC_TXC_EQ64, val)
+#define bfin_read_EMAC_TXC_LT128()		bfin_read32(EMAC_TXC_LT128)
+#define bfin_write_EMAC_TXC_LT128(val)		bfin_write32(EMAC_TXC_LT128, val)
+#define bfin_read_EMAC_TXC_LT256()		bfin_read32(EMAC_TXC_LT256)
+#define bfin_write_EMAC_TXC_LT256(val)		bfin_write32(EMAC_TXC_LT256, val)
+#define bfin_read_EMAC_TXC_LT512()		bfin_read32(EMAC_TXC_LT512)
+#define bfin_write_EMAC_TXC_LT512(val)		bfin_write32(EMAC_TXC_LT512, val)
+#define bfin_read_EMAC_TXC_LT1024()		bfin_read32(EMAC_TXC_LT1024)
+#define bfin_write_EMAC_TXC_LT1024(val)		bfin_write32(EMAC_TXC_LT1024, val)
+#define bfin_read_EMAC_TXC_GE1024()		bfin_read32(EMAC_TXC_GE1024)
+#define bfin_write_EMAC_TXC_GE1024(val)		bfin_write32(EMAC_TXC_GE1024, val)
+#define bfin_read_EMAC_TXC_ABORT()		bfin_read32(EMAC_TXC_ABORT)
+#define bfin_write_EMAC_TXC_ABORT(val)		bfin_write32(EMAC_TXC_ABORT, val)
+
+/* USB Control Registers */
+
+#define bfin_read_USB_FADDR()			bfin_read16(USB_FADDR)
+#define bfin_write_USB_FADDR(val)		bfin_write16(USB_FADDR, val)
+#define bfin_read_USB_POWER()			bfin_read16(USB_POWER)
+#define bfin_write_USB_POWER(val)		bfin_write16(USB_POWER, val)
+#define bfin_read_USB_INTRTX()			bfin_read16(USB_INTRTX)
+#define bfin_write_USB_INTRTX(val)		bfin_write16(USB_INTRTX, val)
+#define bfin_read_USB_INTRRX()			bfin_read16(USB_INTRRX)
+#define bfin_write_USB_INTRRX(val)		bfin_write16(USB_INTRRX, val)
+#define bfin_read_USB_INTRTXE()			bfin_read16(USB_INTRTXE)
+#define bfin_write_USB_INTRTXE(val)		bfin_write16(USB_INTRTXE, val)
+#define bfin_read_USB_INTRRXE()			bfin_read16(USB_INTRRXE)
+#define bfin_write_USB_INTRRXE(val)		bfin_write16(USB_INTRRXE, val)
+#define bfin_read_USB_INTRUSB()			bfin_read16(USB_INTRUSB)
+#define bfin_write_USB_INTRUSB(val)		bfin_write16(USB_INTRUSB, val)
+#define bfin_read_USB_INTRUSBE()		bfin_read16(USB_INTRUSBE)
+#define bfin_write_USB_INTRUSBE(val)		bfin_write16(USB_INTRUSBE, val)
+#define bfin_read_USB_FRAME()			bfin_read16(USB_FRAME)
+#define bfin_write_USB_FRAME(val)		bfin_write16(USB_FRAME, val)
+#define bfin_read_USB_INDEX()			bfin_read16(USB_INDEX)
+#define bfin_write_USB_INDEX(val)		bfin_write16(USB_INDEX, val)
+#define bfin_read_USB_TESTMODE()		bfin_read16(USB_TESTMODE)
+#define bfin_write_USB_TESTMODE(val)		bfin_write16(USB_TESTMODE, val)
+#define bfin_read_USB_GLOBINTR()		bfin_read16(USB_GLOBINTR)
+#define bfin_write_USB_GLOBINTR(val)		bfin_write16(USB_GLOBINTR, val)
+#define bfin_read_USB_GLOBAL_CTL()		bfin_read16(USB_GLOBAL_CTL)
+#define bfin_write_USB_GLOBAL_CTL(val)		bfin_write16(USB_GLOBAL_CTL, val)
+
+/* USB Packet Control Registers */
+
+#define bfin_read_USB_TX_MAX_PACKET()		bfin_read16(USB_TX_MAX_PACKET)
+#define bfin_write_USB_TX_MAX_PACKET(val)	bfin_write16(USB_TX_MAX_PACKET, val)
+#define bfin_read_USB_CSR0()			bfin_read16(USB_CSR0)
+#define bfin_write_USB_CSR0(val)		bfin_write16(USB_CSR0, val)
+#define bfin_read_USB_TXCSR()			bfin_read16(USB_TXCSR)
+#define bfin_write_USB_TXCSR(val)		bfin_write16(USB_TXCSR, val)
+#define bfin_read_USB_RX_MAX_PACKET()		bfin_read16(USB_RX_MAX_PACKET)
+#define bfin_write_USB_RX_MAX_PACKET(val)	bfin_write16(USB_RX_MAX_PACKET, val)
+#define bfin_read_USB_RXCSR()			bfin_read16(USB_RXCSR)
+#define bfin_write_USB_RXCSR(val)		bfin_write16(USB_RXCSR, val)
+#define bfin_read_USB_COUNT0()			bfin_read16(USB_COUNT0)
+#define bfin_write_USB_COUNT0(val)		bfin_write16(USB_COUNT0, val)
+#define bfin_read_USB_RXCOUNT()			bfin_read16(USB_RXCOUNT)
+#define bfin_write_USB_RXCOUNT(val)		bfin_write16(USB_RXCOUNT, val)
+#define bfin_read_USB_TXTYPE()			bfin_read16(USB_TXTYPE)
+#define bfin_write_USB_TXTYPE(val)		bfin_write16(USB_TXTYPE, val)
+#define bfin_read_USB_NAKLIMIT0()		bfin_read16(USB_NAKLIMIT0)
+#define bfin_write_USB_NAKLIMIT0(val)		bfin_write16(USB_NAKLIMIT0, val)
+#define bfin_read_USB_TXINTERVAL()		bfin_read16(USB_TXINTERVAL)
+#define bfin_write_USB_TXINTERVAL(val)		bfin_write16(USB_TXINTERVAL, val)
+#define bfin_read_USB_RXTYPE()			bfin_read16(USB_RXTYPE)
+#define bfin_write_USB_RXTYPE(val)		bfin_write16(USB_RXTYPE, val)
+#define bfin_read_USB_RXINTERVAL()		bfin_read16(USB_RXINTERVAL)
+#define bfin_write_USB_RXINTERVAL(val)		bfin_write16(USB_RXINTERVAL, val)
+#define bfin_read_USB_TXCOUNT()			bfin_read16(USB_TXCOUNT)
+#define bfin_write_USB_TXCOUNT(val)		bfin_write16(USB_TXCOUNT, val)
+
+/* USB Endpoint FIFO Registers */
+
+#define bfin_read_USB_EP0_FIFO()		bfin_read16(USB_EP0_FIFO)
+#define bfin_write_USB_EP0_FIFO(val)		bfin_write16(USB_EP0_FIFO, val)
+#define bfin_read_USB_EP1_FIFO()		bfin_read16(USB_EP1_FIFO)
+#define bfin_write_USB_EP1_FIFO(val)		bfin_write16(USB_EP1_FIFO, val)
+#define bfin_read_USB_EP2_FIFO()		bfin_read16(USB_EP2_FIFO)
+#define bfin_write_USB_EP2_FIFO(val)		bfin_write16(USB_EP2_FIFO, val)
+#define bfin_read_USB_EP3_FIFO()		bfin_read16(USB_EP3_FIFO)
+#define bfin_write_USB_EP3_FIFO(val)		bfin_write16(USB_EP3_FIFO, val)
+#define bfin_read_USB_EP4_FIFO()		bfin_read16(USB_EP4_FIFO)
+#define bfin_write_USB_EP4_FIFO(val)		bfin_write16(USB_EP4_FIFO, val)
+#define bfin_read_USB_EP5_FIFO()		bfin_read16(USB_EP5_FIFO)
+#define bfin_write_USB_EP5_FIFO(val)		bfin_write16(USB_EP5_FIFO, val)
+#define bfin_read_USB_EP6_FIFO()		bfin_read16(USB_EP6_FIFO)
+#define bfin_write_USB_EP6_FIFO(val)		bfin_write16(USB_EP6_FIFO, val)
+#define bfin_read_USB_EP7_FIFO()		bfin_read16(USB_EP7_FIFO)
+#define bfin_write_USB_EP7_FIFO(val)		bfin_write16(USB_EP7_FIFO, val)
+
+/* USB OTG Control Registers */
+
+#define bfin_read_USB_OTG_DEV_CTL()		bfin_read16(USB_OTG_DEV_CTL)
+#define bfin_write_USB_OTG_DEV_CTL(val)		bfin_write16(USB_OTG_DEV_CTL, val)
+#define bfin_read_USB_OTG_VBUS_IRQ()		bfin_read16(USB_OTG_VBUS_IRQ)
+#define bfin_write_USB_OTG_VBUS_IRQ(val)	bfin_write16(USB_OTG_VBUS_IRQ, val)
+#define bfin_read_USB_OTG_VBUS_MASK()		bfin_read16(USB_OTG_VBUS_MASK)
+#define bfin_write_USB_OTG_VBUS_MASK(val)	bfin_write16(USB_OTG_VBUS_MASK, val)
+
+/* USB Phy Control Registers */
+
+#define bfin_read_USB_LINKINFO()		bfin_read16(USB_LINKINFO)
+#define bfin_write_USB_LINKINFO(val)		bfin_write16(USB_LINKINFO, val)
+#define bfin_read_USB_VPLEN()			bfin_read16(USB_VPLEN)
+#define bfin_write_USB_VPLEN(val)		bfin_write16(USB_VPLEN, val)
+#define bfin_read_USB_HS_EOF1()			bfin_read16(USB_HS_EOF1)
+#define bfin_write_USB_HS_EOF1(val)		bfin_write16(USB_HS_EOF1, val)
+#define bfin_read_USB_FS_EOF1()			bfin_read16(USB_FS_EOF1)
+#define bfin_write_USB_FS_EOF1(val)		bfin_write16(USB_FS_EOF1, val)
+#define bfin_read_USB_LS_EOF1()			bfin_read16(USB_LS_EOF1)
+#define bfin_write_USB_LS_EOF1(val)		bfin_write16(USB_LS_EOF1, val)
+
+/* (APHY_CNTRL is for ADI usage only) */
+
+#define bfin_read_USB_APHY_CNTRL()		bfin_read16(USB_APHY_CNTRL)
+#define bfin_write_USB_APHY_CNTRL(val)		bfin_write16(USB_APHY_CNTRL, val)
+
+/* (APHY_CALIB is for ADI usage only) */
+
+#define bfin_read_USB_APHY_CALIB()		bfin_read16(USB_APHY_CALIB)
+#define bfin_write_USB_APHY_CALIB(val)		bfin_write16(USB_APHY_CALIB, val)
+
+#define bfin_read_USB_APHY_CNTRL2()		bfin_read16(USB_APHY_CNTRL2)
+#define bfin_write_USB_APHY_CNTRL2(val)		bfin_write16(USB_APHY_CNTRL2, val)
+
+/* (PHY_TEST is for ADI usage only) */
+
+#define bfin_read_USB_PHY_TEST()		bfin_read16(USB_PHY_TEST)
+#define bfin_write_USB_PHY_TEST(val)		bfin_write16(USB_PHY_TEST, val)
+
+#define bfin_read_USB_PLLOSC_CTRL()		bfin_read16(USB_PLLOSC_CTRL)
+#define bfin_write_USB_PLLOSC_CTRL(val)		bfin_write16(USB_PLLOSC_CTRL, val)
+#define bfin_read_USB_SRP_CLKDIV()		bfin_read16(USB_SRP_CLKDIV)
+#define bfin_write_USB_SRP_CLKDIV(val)		bfin_write16(USB_SRP_CLKDIV, val)
+
+/* USB Endpoint 0 Control Registers */
+
+#define bfin_read_USB_EP_NI0_TXMAXP()		bfin_read16(USB_EP_NI0_TXMAXP)
+#define bfin_write_USB_EP_NI0_TXMAXP(val)	bfin_write16(USB_EP_NI0_TXMAXP, val)
+#define bfin_read_USB_EP_NI0_TXCSR()		bfin_read16(USB_EP_NI0_TXCSR)
+#define bfin_write_USB_EP_NI0_TXCSR(val)	bfin_write16(USB_EP_NI0_TXCSR, val)
+#define bfin_read_USB_EP_NI0_RXMAXP()		bfin_read16(USB_EP_NI0_RXMAXP)
+#define bfin_write_USB_EP_NI0_RXMAXP(val)	bfin_write16(USB_EP_NI0_RXMAXP, val)
+#define bfin_read_USB_EP_NI0_RXCSR()		bfin_read16(USB_EP_NI0_RXCSR)
+#define bfin_write_USB_EP_NI0_RXCSR(val)	bfin_write16(USB_EP_NI0_RXCSR, val)
+#define bfin_read_USB_EP_NI0_RXCOUNT()		bfin_read16(USB_EP_NI0_RXCOUNT)
+#define bfin_write_USB_EP_NI0_RXCOUNT(val)	bfin_write16(USB_EP_NI0_RXCOUNT, val)
+#define bfin_read_USB_EP_NI0_TXTYPE()		bfin_read16(USB_EP_NI0_TXTYPE)
+#define bfin_write_USB_EP_NI0_TXTYPE(val)	bfin_write16(USB_EP_NI0_TXTYPE, val)
+#define bfin_read_USB_EP_NI0_TXINTERVAL()	bfin_read16(USB_EP_NI0_TXINTERVAL)
+#define bfin_write_USB_EP_NI0_TXINTERVAL(val)	bfin_write16(USB_EP_NI0_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI0_RXTYPE()		bfin_read16(USB_EP_NI0_RXTYPE)
+#define bfin_write_USB_EP_NI0_RXTYPE(val)	bfin_write16(USB_EP_NI0_RXTYPE, val)
+#define bfin_read_USB_EP_NI0_RXINTERVAL()	bfin_read16(USB_EP_NI0_RXINTERVAL)
+#define bfin_write_USB_EP_NI0_RXINTERVAL(val)	bfin_write16(USB_EP_NI0_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI0_TXCOUNT()		bfin_read16(USB_EP_NI0_TXCOUNT)
+#define bfin_write_USB_EP_NI0_TXCOUNT(val)	bfin_write16(USB_EP_NI0_TXCOUNT, val)
+
+/* USB Endpoint 1 Control Registers */
+
+#define bfin_read_USB_EP_NI1_TXMAXP()		bfin_read16(USB_EP_NI1_TXMAXP)
+#define bfin_write_USB_EP_NI1_TXMAXP(val)	bfin_write16(USB_EP_NI1_TXMAXP, val)
+#define bfin_read_USB_EP_NI1_TXCSR()		bfin_read16(USB_EP_NI1_TXCSR)
+#define bfin_write_USB_EP_NI1_TXCSR(val)	bfin_write16(USB_EP_NI1_TXCSR, val)
+#define bfin_read_USB_EP_NI1_RXMAXP()		bfin_read16(USB_EP_NI1_RXMAXP)
+#define bfin_write_USB_EP_NI1_RXMAXP(val)	bfin_write16(USB_EP_NI1_RXMAXP, val)
+#define bfin_read_USB_EP_NI1_RXCSR()		bfin_read16(USB_EP_NI1_RXCSR)
+#define bfin_write_USB_EP_NI1_RXCSR(val)	bfin_write16(USB_EP_NI1_RXCSR, val)
+#define bfin_read_USB_EP_NI1_RXCOUNT()		bfin_read16(USB_EP_NI1_RXCOUNT)
+#define bfin_write_USB_EP_NI1_RXCOUNT(val)	bfin_write16(USB_EP_NI1_RXCOUNT, val)
+#define bfin_read_USB_EP_NI1_TXTYPE()		bfin_read16(USB_EP_NI1_TXTYPE)
+#define bfin_write_USB_EP_NI1_TXTYPE(val)	bfin_write16(USB_EP_NI1_TXTYPE, val)
+#define bfin_read_USB_EP_NI1_TXINTERVAL()	bfin_read16(USB_EP_NI1_TXINTERVAL)
+#define bfin_write_USB_EP_NI1_TXINTERVAL(val)	bfin_write16(USB_EP_NI1_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI1_RXTYPE()		bfin_read16(USB_EP_NI1_RXTYPE)
+#define bfin_write_USB_EP_NI1_RXTYPE(val)	bfin_write16(USB_EP_NI1_RXTYPE, val)
+#define bfin_read_USB_EP_NI1_RXINTERVAL()	bfin_read16(USB_EP_NI1_RXINTERVAL)
+#define bfin_write_USB_EP_NI1_RXINTERVAL(val)	bfin_write16(USB_EP_NI1_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI1_TXCOUNT()		bfin_read16(USB_EP_NI1_TXCOUNT)
+#define bfin_write_USB_EP_NI1_TXCOUNT(val)	bfin_write16(USB_EP_NI1_TXCOUNT, val)
+
+/* USB Endpoint 2 Control Registers */
+
+#define bfin_read_USB_EP_NI2_TXMAXP()		bfin_read16(USB_EP_NI2_TXMAXP)
+#define bfin_write_USB_EP_NI2_TXMAXP(val)	bfin_write16(USB_EP_NI2_TXMAXP, val)
+#define bfin_read_USB_EP_NI2_TXCSR()		bfin_read16(USB_EP_NI2_TXCSR)
+#define bfin_write_USB_EP_NI2_TXCSR(val)	bfin_write16(USB_EP_NI2_TXCSR, val)
+#define bfin_read_USB_EP_NI2_RXMAXP()		bfin_read16(USB_EP_NI2_RXMAXP)
+#define bfin_write_USB_EP_NI2_RXMAXP(val)	bfin_write16(USB_EP_NI2_RXMAXP, val)
+#define bfin_read_USB_EP_NI2_RXCSR()		bfin_read16(USB_EP_NI2_RXCSR)
+#define bfin_write_USB_EP_NI2_RXCSR(val)	bfin_write16(USB_EP_NI2_RXCSR, val)
+#define bfin_read_USB_EP_NI2_RXCOUNT()		bfin_read16(USB_EP_NI2_RXCOUNT)
+#define bfin_write_USB_EP_NI2_RXCOUNT(val)	bfin_write16(USB_EP_NI2_RXCOUNT, val)
+#define bfin_read_USB_EP_NI2_TXTYPE()		bfin_read16(USB_EP_NI2_TXTYPE)
+#define bfin_write_USB_EP_NI2_TXTYPE(val)	bfin_write16(USB_EP_NI2_TXTYPE, val)
+#define bfin_read_USB_EP_NI2_TXINTERVAL()	bfin_read16(USB_EP_NI2_TXINTERVAL)
+#define bfin_write_USB_EP_NI2_TXINTERVAL(val)	bfin_write16(USB_EP_NI2_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI2_RXTYPE()		bfin_read16(USB_EP_NI2_RXTYPE)
+#define bfin_write_USB_EP_NI2_RXTYPE(val)	bfin_write16(USB_EP_NI2_RXTYPE, val)
+#define bfin_read_USB_EP_NI2_RXINTERVAL()	bfin_read16(USB_EP_NI2_RXINTERVAL)
+#define bfin_write_USB_EP_NI2_RXINTERVAL(val)	bfin_write16(USB_EP_NI2_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI2_TXCOUNT()		bfin_read16(USB_EP_NI2_TXCOUNT)
+#define bfin_write_USB_EP_NI2_TXCOUNT(val)	bfin_write16(USB_EP_NI2_TXCOUNT, val)
+
+/* USB Endpoint 3 Control Registers */
+
+#define bfin_read_USB_EP_NI3_TXMAXP()		bfin_read16(USB_EP_NI3_TXMAXP)
+#define bfin_write_USB_EP_NI3_TXMAXP(val)	bfin_write16(USB_EP_NI3_TXMAXP, val)
+#define bfin_read_USB_EP_NI3_TXCSR()		bfin_read16(USB_EP_NI3_TXCSR)
+#define bfin_write_USB_EP_NI3_TXCSR(val)	bfin_write16(USB_EP_NI3_TXCSR, val)
+#define bfin_read_USB_EP_NI3_RXMAXP()		bfin_read16(USB_EP_NI3_RXMAXP)
+#define bfin_write_USB_EP_NI3_RXMAXP(val)	bfin_write16(USB_EP_NI3_RXMAXP, val)
+#define bfin_read_USB_EP_NI3_RXCSR()		bfin_read16(USB_EP_NI3_RXCSR)
+#define bfin_write_USB_EP_NI3_RXCSR(val)	bfin_write16(USB_EP_NI3_RXCSR, val)
+#define bfin_read_USB_EP_NI3_RXCOUNT()		bfin_read16(USB_EP_NI3_RXCOUNT)
+#define bfin_write_USB_EP_NI3_RXCOUNT(val)	bfin_write16(USB_EP_NI3_RXCOUNT, val)
+#define bfin_read_USB_EP_NI3_TXTYPE()		bfin_read16(USB_EP_NI3_TXTYPE)
+#define bfin_write_USB_EP_NI3_TXTYPE(val)	bfin_write16(USB_EP_NI3_TXTYPE, val)
+#define bfin_read_USB_EP_NI3_TXINTERVAL()	bfin_read16(USB_EP_NI3_TXINTERVAL)
+#define bfin_write_USB_EP_NI3_TXINTERVAL(val)	bfin_write16(USB_EP_NI3_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI3_RXTYPE()		bfin_read16(USB_EP_NI3_RXTYPE)
+#define bfin_write_USB_EP_NI3_RXTYPE(val)	bfin_write16(USB_EP_NI3_RXTYPE, val)
+#define bfin_read_USB_EP_NI3_RXINTERVAL()	bfin_read16(USB_EP_NI3_RXINTERVAL)
+#define bfin_write_USB_EP_NI3_RXINTERVAL(val)	bfin_write16(USB_EP_NI3_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI3_TXCOUNT()		bfin_read16(USB_EP_NI3_TXCOUNT)
+#define bfin_write_USB_EP_NI3_TXCOUNT(val)	bfin_write16(USB_EP_NI3_TXCOUNT, val)
+
+/* USB Endpoint 4 Control Registers */
+
+#define bfin_read_USB_EP_NI4_TXMAXP()		bfin_read16(USB_EP_NI4_TXMAXP)
+#define bfin_write_USB_EP_NI4_TXMAXP(val)	bfin_write16(USB_EP_NI4_TXMAXP, val)
+#define bfin_read_USB_EP_NI4_TXCSR()		bfin_read16(USB_EP_NI4_TXCSR)
+#define bfin_write_USB_EP_NI4_TXCSR(val)	bfin_write16(USB_EP_NI4_TXCSR, val)
+#define bfin_read_USB_EP_NI4_RXMAXP()		bfin_read16(USB_EP_NI4_RXMAXP)
+#define bfin_write_USB_EP_NI4_RXMAXP(val)	bfin_write16(USB_EP_NI4_RXMAXP, val)
+#define bfin_read_USB_EP_NI4_RXCSR()		bfin_read16(USB_EP_NI4_RXCSR)
+#define bfin_write_USB_EP_NI4_RXCSR(val)	bfin_write16(USB_EP_NI4_RXCSR, val)
+#define bfin_read_USB_EP_NI4_RXCOUNT()		bfin_read16(USB_EP_NI4_RXCOUNT)
+#define bfin_write_USB_EP_NI4_RXCOUNT(val)	bfin_write16(USB_EP_NI4_RXCOUNT, val)
+#define bfin_read_USB_EP_NI4_TXTYPE()		bfin_read16(USB_EP_NI4_TXTYPE)
+#define bfin_write_USB_EP_NI4_TXTYPE(val)	bfin_write16(USB_EP_NI4_TXTYPE, val)
+#define bfin_read_USB_EP_NI4_TXINTERVAL()	bfin_read16(USB_EP_NI4_TXINTERVAL)
+#define bfin_write_USB_EP_NI4_TXINTERVAL(val)	bfin_write16(USB_EP_NI4_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI4_RXTYPE()		bfin_read16(USB_EP_NI4_RXTYPE)
+#define bfin_write_USB_EP_NI4_RXTYPE(val)	bfin_write16(USB_EP_NI4_RXTYPE, val)
+#define bfin_read_USB_EP_NI4_RXINTERVAL()	bfin_read16(USB_EP_NI4_RXINTERVAL)
+#define bfin_write_USB_EP_NI4_RXINTERVAL(val)	bfin_write16(USB_EP_NI4_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI4_TXCOUNT()		bfin_read16(USB_EP_NI4_TXCOUNT)
+#define bfin_write_USB_EP_NI4_TXCOUNT(val)	bfin_write16(USB_EP_NI4_TXCOUNT, val)
+
+/* USB Endpoint 5 Control Registers */
+
+#define bfin_read_USB_EP_NI5_TXMAXP()		bfin_read16(USB_EP_NI5_TXMAXP)
+#define bfin_write_USB_EP_NI5_TXMAXP(val)	bfin_write16(USB_EP_NI5_TXMAXP, val)
+#define bfin_read_USB_EP_NI5_TXCSR()		bfin_read16(USB_EP_NI5_TXCSR)
+#define bfin_write_USB_EP_NI5_TXCSR(val)	bfin_write16(USB_EP_NI5_TXCSR, val)
+#define bfin_read_USB_EP_NI5_RXMAXP()		bfin_read16(USB_EP_NI5_RXMAXP)
+#define bfin_write_USB_EP_NI5_RXMAXP(val)	bfin_write16(USB_EP_NI5_RXMAXP, val)
+#define bfin_read_USB_EP_NI5_RXCSR()		bfin_read16(USB_EP_NI5_RXCSR)
+#define bfin_write_USB_EP_NI5_RXCSR(val)	bfin_write16(USB_EP_NI5_RXCSR, val)
+#define bfin_read_USB_EP_NI5_RXCOUNT()		bfin_read16(USB_EP_NI5_RXCOUNT)
+#define bfin_write_USB_EP_NI5_RXCOUNT(val)	bfin_write16(USB_EP_NI5_RXCOUNT, val)
+#define bfin_read_USB_EP_NI5_TXTYPE()		bfin_read16(USB_EP_NI5_TXTYPE)
+#define bfin_write_USB_EP_NI5_TXTYPE(val)	bfin_write16(USB_EP_NI5_TXTYPE, val)
+#define bfin_read_USB_EP_NI5_TXINTERVAL()	bfin_read16(USB_EP_NI5_TXINTERVAL)
+#define bfin_write_USB_EP_NI5_TXINTERVAL(val)	bfin_write16(USB_EP_NI5_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI5_RXTYPE()		bfin_read16(USB_EP_NI5_RXTYPE)
+#define bfin_write_USB_EP_NI5_RXTYPE(val)	bfin_write16(USB_EP_NI5_RXTYPE, val)
+#define bfin_read_USB_EP_NI5_RXINTERVAL()	bfin_read16(USB_EP_NI5_RXINTERVAL)
+#define bfin_write_USB_EP_NI5_RXINTERVAL(val)	bfin_write16(USB_EP_NI5_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI5_TXCOUNT()		bfin_read16(USB_EP_NI5_TXCOUNT)
+#define bfin_write_USB_EP_NI5_TXCOUNT(val)	bfin_write16(USB_EP_NI5_TXCOUNT, val)
+
+/* USB Endpoint 6 Control Registers */
+
+#define bfin_read_USB_EP_NI6_TXMAXP()		bfin_read16(USB_EP_NI6_TXMAXP)
+#define bfin_write_USB_EP_NI6_TXMAXP(val)	bfin_write16(USB_EP_NI6_TXMAXP, val)
+#define bfin_read_USB_EP_NI6_TXCSR()		bfin_read16(USB_EP_NI6_TXCSR)
+#define bfin_write_USB_EP_NI6_TXCSR(val)	bfin_write16(USB_EP_NI6_TXCSR, val)
+#define bfin_read_USB_EP_NI6_RXMAXP()		bfin_read16(USB_EP_NI6_RXMAXP)
+#define bfin_write_USB_EP_NI6_RXMAXP(val)	bfin_write16(USB_EP_NI6_RXMAXP, val)
+#define bfin_read_USB_EP_NI6_RXCSR()		bfin_read16(USB_EP_NI6_RXCSR)
+#define bfin_write_USB_EP_NI6_RXCSR(val)	bfin_write16(USB_EP_NI6_RXCSR, val)
+#define bfin_read_USB_EP_NI6_RXCOUNT()		bfin_read16(USB_EP_NI6_RXCOUNT)
+#define bfin_write_USB_EP_NI6_RXCOUNT(val)	bfin_write16(USB_EP_NI6_RXCOUNT, val)
+#define bfin_read_USB_EP_NI6_TXTYPE()		bfin_read16(USB_EP_NI6_TXTYPE)
+#define bfin_write_USB_EP_NI6_TXTYPE(val)	bfin_write16(USB_EP_NI6_TXTYPE, val)
+#define bfin_read_USB_EP_NI6_TXINTERVAL()	bfin_read16(USB_EP_NI6_TXINTERVAL)
+#define bfin_write_USB_EP_NI6_TXINTERVAL(val)	bfin_write16(USB_EP_NI6_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI6_RXTYPE()		bfin_read16(USB_EP_NI6_RXTYPE)
+#define bfin_write_USB_EP_NI6_RXTYPE(val)	bfin_write16(USB_EP_NI6_RXTYPE, val)
+#define bfin_read_USB_EP_NI6_RXINTERVAL()	bfin_read16(USB_EP_NI6_RXINTERVAL)
+#define bfin_write_USB_EP_NI6_RXINTERVAL(val)	bfin_write16(USB_EP_NI6_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI6_TXCOUNT()		bfin_read16(USB_EP_NI6_TXCOUNT)
+#define bfin_write_USB_EP_NI6_TXCOUNT(val)	bfin_write16(USB_EP_NI6_TXCOUNT, val)
+
+/* USB Endpoint 7 Control Registers */
+
+#define bfin_read_USB_EP_NI7_TXMAXP()		bfin_read16(USB_EP_NI7_TXMAXP)
+#define bfin_write_USB_EP_NI7_TXMAXP(val)	bfin_write16(USB_EP_NI7_TXMAXP, val)
+#define bfin_read_USB_EP_NI7_TXCSR()		bfin_read16(USB_EP_NI7_TXCSR)
+#define bfin_write_USB_EP_NI7_TXCSR(val)	bfin_write16(USB_EP_NI7_TXCSR, val)
+#define bfin_read_USB_EP_NI7_RXMAXP()		bfin_read16(USB_EP_NI7_RXMAXP)
+#define bfin_write_USB_EP_NI7_RXMAXP(val)	bfin_write16(USB_EP_NI7_RXMAXP, val)
+#define bfin_read_USB_EP_NI7_RXCSR()		bfin_read16(USB_EP_NI7_RXCSR)
+#define bfin_write_USB_EP_NI7_RXCSR(val)	bfin_write16(USB_EP_NI7_RXCSR, val)
+#define bfin_read_USB_EP_NI7_RXCOUNT()		bfin_read16(USB_EP_NI7_RXCOUNT)
+#define bfin_write_USB_EP_NI7_RXCOUNT(val)	bfin_write16(USB_EP_NI7_RXCOUNT, val)
+#define bfin_read_USB_EP_NI7_TXTYPE()		bfin_read16(USB_EP_NI7_TXTYPE)
+#define bfin_write_USB_EP_NI7_TXTYPE(val)	bfin_write16(USB_EP_NI7_TXTYPE, val)
+#define bfin_read_USB_EP_NI7_TXINTERVAL()	bfin_read16(USB_EP_NI7_TXINTERVAL)
+#define bfin_write_USB_EP_NI7_TXINTERVAL(val)	bfin_write16(USB_EP_NI7_TXINTERVAL, val)
+#define bfin_read_USB_EP_NI7_RXTYPE()		bfin_read16(USB_EP_NI7_RXTYPE)
+#define bfin_write_USB_EP_NI7_RXTYPE(val)	bfin_write16(USB_EP_NI7_RXTYPE, val)
+#define bfin_read_USB_EP_NI7_RXINTERVAL()	bfin_read16(USB_EP_NI7_RXINTERVAL)
+#define bfin_write_USB_EP_NI7_RXINTERVAL(val)	bfin_write16(USB_EP_NI7_RXINTERVAL, val)
+#define bfin_read_USB_EP_NI7_TXCOUNT()		bfin_read16(USB_EP_NI7_TXCOUNT)
+#define bfin_write_USB_EP_NI7_TXCOUNT(val)	bfin_write16(USB_EP_NI7_TXCOUNT, val)
+
+#define bfin_read_USB_DMA_INTERRUPT()		bfin_read16(USB_DMA_INTERRUPT)
+#define bfin_write_USB_DMA_INTERRUPT(val)	bfin_write16(USB_DMA_INTERRUPT, val)
+
+/* USB Channel 0 Config Registers */
+
+#define bfin_read_USB_DMA0CONTROL()		bfin_read16(USB_DMA0CONTROL)
+#define bfin_write_USB_DMA0CONTROL(val)		bfin_write16(USB_DMA0CONTROL, val)
+#define bfin_read_USB_DMA0ADDRLOW()		bfin_read16(USB_DMA0ADDRLOW)
+#define bfin_write_USB_DMA0ADDRLOW(val)		bfin_write16(USB_DMA0ADDRLOW, val)
+#define bfin_read_USB_DMA0ADDRHIGH()		bfin_read16(USB_DMA0ADDRHIGH)
+#define bfin_write_USB_DMA0ADDRHIGH(val)	bfin_write16(USB_DMA0ADDRHIGH, val)
+#define bfin_read_USB_DMA0COUNTLOW()		bfin_read16(USB_DMA0COUNTLOW)
+#define bfin_write_USB_DMA0COUNTLOW(val)	bfin_write16(USB_DMA0COUNTLOW, val)
+#define bfin_read_USB_DMA0COUNTHIGH()		bfin_read16(USB_DMA0COUNTHIGH)
+#define bfin_write_USB_DMA0COUNTHIGH(val)	bfin_write16(USB_DMA0COUNTHIGH, val)
+
+/* USB Channel 1 Config Registers */
+
+#define bfin_read_USB_DMA1CONTROL()		bfin_read16(USB_DMA1CONTROL)
+#define bfin_write_USB_DMA1CONTROL(val)		bfin_write16(USB_DMA1CONTROL, val)
+#define bfin_read_USB_DMA1ADDRLOW()		bfin_read16(USB_DMA1ADDRLOW)
+#define bfin_write_USB_DMA1ADDRLOW(val)		bfin_write16(USB_DMA1ADDRLOW, val)
+#define bfin_read_USB_DMA1ADDRHIGH()		bfin_read16(USB_DMA1ADDRHIGH)
+#define bfin_write_USB_DMA1ADDRHIGH(val)	bfin_write16(USB_DMA1ADDRHIGH, val)
+#define bfin_read_USB_DMA1COUNTLOW()		bfin_read16(USB_DMA1COUNTLOW)
+#define bfin_write_USB_DMA1COUNTLOW(val)	bfin_write16(USB_DMA1COUNTLOW, val)
+#define bfin_read_USB_DMA1COUNTHIGH()		bfin_read16(USB_DMA1COUNTHIGH)
+#define bfin_write_USB_DMA1COUNTHIGH(val)	bfin_write16(USB_DMA1COUNTHIGH, val)
+
+/* USB Channel 2 Config Registers */
+
+#define bfin_read_USB_DMA2CONTROL()		bfin_read16(USB_DMA2CONTROL)
+#define bfin_write_USB_DMA2CONTROL(val)		bfin_write16(USB_DMA2CONTROL, val)
+#define bfin_read_USB_DMA2ADDRLOW()		bfin_read16(USB_DMA2ADDRLOW)
+#define bfin_write_USB_DMA2ADDRLOW(val)		bfin_write16(USB_DMA2ADDRLOW, val)
+#define bfin_read_USB_DMA2ADDRHIGH()		bfin_read16(USB_DMA2ADDRHIGH)
+#define bfin_write_USB_DMA2ADDRHIGH(val)	bfin_write16(USB_DMA2ADDRHIGH, val)
+#define bfin_read_USB_DMA2COUNTLOW()		bfin_read16(USB_DMA2COUNTLOW)
+#define bfin_write_USB_DMA2COUNTLOW(val)	bfin_write16(USB_DMA2COUNTLOW, val)
+#define bfin_read_USB_DMA2COUNTHIGH()		bfin_read16(USB_DMA2COUNTHIGH)
+#define bfin_write_USB_DMA2COUNTHIGH(val)	bfin_write16(USB_DMA2COUNTHIGH, val)
+
+/* USB Channel 3 Config Registers */
+
+#define bfin_read_USB_DMA3CONTROL()		bfin_read16(USB_DMA3CONTROL)
+#define bfin_write_USB_DMA3CONTROL(val)		bfin_write16(USB_DMA3CONTROL, val)
+#define bfin_read_USB_DMA3ADDRLOW()		bfin_read16(USB_DMA3ADDRLOW)
+#define bfin_write_USB_DMA3ADDRLOW(val)		bfin_write16(USB_DMA3ADDRLOW, val)
+#define bfin_read_USB_DMA3ADDRHIGH()		bfin_read16(USB_DMA3ADDRHIGH)
+#define bfin_write_USB_DMA3ADDRHIGH(val)	bfin_write16(USB_DMA3ADDRHIGH, val)
+#define bfin_read_USB_DMA3COUNTLOW()		bfin_read16(USB_DMA3COUNTLOW)
+#define bfin_write_USB_DMA3COUNTLOW(val)	bfin_write16(USB_DMA3COUNTLOW, val)
+#define bfin_read_USB_DMA3COUNTHIGH()		bfin_read16(USB_DMA3COUNTHIGH)
+#define bfin_write_USB_DMA3COUNTHIGH(val)	bfin_write16(USB_DMA3COUNTHIGH, val)
+
+/* USB Channel 4 Config Registers */
+
+#define bfin_read_USB_DMA4CONTROL()		bfin_read16(USB_DMA4CONTROL)
+#define bfin_write_USB_DMA4CONTROL(val)		bfin_write16(USB_DMA4CONTROL, val)
+#define bfin_read_USB_DMA4ADDRLOW()		bfin_read16(USB_DMA4ADDRLOW)
+#define bfin_write_USB_DMA4ADDRLOW(val)		bfin_write16(USB_DMA4ADDRLOW, val)
+#define bfin_read_USB_DMA4ADDRHIGH()		bfin_read16(USB_DMA4ADDRHIGH)
+#define bfin_write_USB_DMA4ADDRHIGH(val)	bfin_write16(USB_DMA4ADDRHIGH, val)
+#define bfin_read_USB_DMA4COUNTLOW()		bfin_read16(USB_DMA4COUNTLOW)
+#define bfin_write_USB_DMA4COUNTLOW(val)	bfin_write16(USB_DMA4COUNTLOW, val)
+#define bfin_read_USB_DMA4COUNTHIGH()		bfin_read16(USB_DMA4COUNTHIGH)
+#define bfin_write_USB_DMA4COUNTHIGH(val)	bfin_write16(USB_DMA4COUNTHIGH, val)
+
+/* USB Channel 5 Config Registers */
+
+#define bfin_read_USB_DMA5CONTROL()		bfin_read16(USB_DMA5CONTROL)
+#define bfin_write_USB_DMA5CONTROL(val)		bfin_write16(USB_DMA5CONTROL, val)
+#define bfin_read_USB_DMA5ADDRLOW()		bfin_read16(USB_DMA5ADDRLOW)
+#define bfin_write_USB_DMA5ADDRLOW(val)		bfin_write16(USB_DMA5ADDRLOW, val)
+#define bfin_read_USB_DMA5ADDRHIGH()		bfin_read16(USB_DMA5ADDRHIGH)
+#define bfin_write_USB_DMA5ADDRHIGH(val)	bfin_write16(USB_DMA5ADDRHIGH, val)
+#define bfin_read_USB_DMA5COUNTLOW()		bfin_read16(USB_DMA5COUNTLOW)
+#define bfin_write_USB_DMA5COUNTLOW(val)	bfin_write16(USB_DMA5COUNTLOW, val)
+#define bfin_read_USB_DMA5COUNTHIGH()		bfin_read16(USB_DMA5COUNTHIGH)
+#define bfin_write_USB_DMA5COUNTHIGH(val)	bfin_write16(USB_DMA5COUNTHIGH, val)
+
+/* USB Channel 6 Config Registers */
+
+#define bfin_read_USB_DMA6CONTROL()		bfin_read16(USB_DMA6CONTROL)
+#define bfin_write_USB_DMA6CONTROL(val)		bfin_write16(USB_DMA6CONTROL, val)
+#define bfin_read_USB_DMA6ADDRLOW()		bfin_read16(USB_DMA6ADDRLOW)
+#define bfin_write_USB_DMA6ADDRLOW(val)		bfin_write16(USB_DMA6ADDRLOW, val)
+#define bfin_read_USB_DMA6ADDRHIGH()		bfin_read16(USB_DMA6ADDRHIGH)
+#define bfin_write_USB_DMA6ADDRHIGH(val)	bfin_write16(USB_DMA6ADDRHIGH, val)
+#define bfin_read_USB_DMA6COUNTLOW()		bfin_read16(USB_DMA6COUNTLOW)
+#define bfin_write_USB_DMA6COUNTLOW(val)	bfin_write16(USB_DMA6COUNTLOW, val)
+#define bfin_read_USB_DMA6COUNTHIGH()		bfin_read16(USB_DMA6COUNTHIGH)
+#define bfin_write_USB_DMA6COUNTHIGH(val)	bfin_write16(USB_DMA6COUNTHIGH, val)
+
+/* USB Channel 7 Config Registers */
+
+#define bfin_read_USB_DMA7CONTROL()		bfin_read16(USB_DMA7CONTROL)
+#define bfin_write_USB_DMA7CONTROL(val)		bfin_write16(USB_DMA7CONTROL, val)
+#define bfin_read_USB_DMA7ADDRLOW()		bfin_read16(USB_DMA7ADDRLOW)
+#define bfin_write_USB_DMA7ADDRLOW(val)		bfin_write16(USB_DMA7ADDRLOW, val)
+#define bfin_read_USB_DMA7ADDRHIGH()		bfin_read16(USB_DMA7ADDRHIGH)
+#define bfin_write_USB_DMA7ADDRHIGH(val)	bfin_write16(USB_DMA7ADDRHIGH, val)
+#define bfin_read_USB_DMA7COUNTLOW()		bfin_read16(USB_DMA7COUNTLOW)
+#define bfin_write_USB_DMA7COUNTLOW(val)	bfin_write16(USB_DMA7COUNTLOW, val)
+#define bfin_read_USB_DMA7COUNTHIGH()		bfin_read16(USB_DMA7COUNTHIGH)
+#define bfin_write_USB_DMA7COUNTHIGH(val)	bfin_write16(USB_DMA7COUNTHIGH, val)
+
+#endif /* _CDEF_BF527_H */
diff --git a/arch/blackfin/mach-bf527/include/mach/cdefBF52x_base.h b/arch/blackfin/mach-bf527/include/mach/cdefBF52x_base.h
new file mode 100644
index 00000000000..9a814b9a12b
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/cdefBF52x_base.h
@@ -0,0 +1,1204 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/cdefBF52x_base.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _CDEF_BF52X_H
+#define _CDEF_BF52X_H
+
+#include <asm/system.h>
+#include <asm/blackfin.h>
+
+#include "defBF52x_base.h"
+
+/* Include core specific register pointer definitions 								*/
+#include <asm/cdef_LPBlackfin.h>
+
+/* ==== begin from cdefBF534.h ==== */
+
+/* Clock and System Control	(0xFFC00000 - 0xFFC000FF)								*/
+#define bfin_read_PLL_CTL()			bfin_read16(PLL_CTL)
+/* Writing to PLL_CTL initiates a PLL relock sequence. */
+static __inline__ void bfin_write_PLL_CTL(unsigned int val)
+{
+	unsigned long flags, iwr0, iwr1;
+
+	if (val == bfin_read_PLL_CTL())
+		return;
+
+	local_irq_save(flags);
+	/* Enable the PLL Wakeup bit in SIC IWR */
+	iwr0 = bfin_read32(SIC_IWR0);
+	iwr1 = bfin_read32(SIC_IWR1);
+	/* Only allow PPL Wakeup) */
+	bfin_write32(SIC_IWR0, IWR_ENABLE(0));
+	bfin_write32(SIC_IWR1, 0);
+
+	bfin_write16(PLL_CTL, val);
+	SSYNC();
+	asm("IDLE;");
+
+	bfin_write32(SIC_IWR0, iwr0);
+	bfin_write32(SIC_IWR1, iwr1);
+	local_irq_restore(flags);
+}
+#define bfin_read_PLL_DIV()			bfin_read16(PLL_DIV)
+#define bfin_write_PLL_DIV(val)			bfin_write16(PLL_DIV, val)
+#define bfin_read_VR_CTL()			bfin_read16(VR_CTL)
+/* Writing to VR_CTL initiates a PLL relock sequence. */
+static __inline__ void bfin_write_VR_CTL(unsigned int val)
+{
+	unsigned long flags, iwr0, iwr1;
+
+	if (val == bfin_read_VR_CTL())
+		return;
+
+	local_irq_save(flags);
+	/* Enable the PLL Wakeup bit in SIC IWR */
+	iwr0 = bfin_read32(SIC_IWR0);
+	iwr1 = bfin_read32(SIC_IWR1);
+	/* Only allow PPL Wakeup) */
+	bfin_write32(SIC_IWR0, IWR_ENABLE(0));
+	bfin_write32(SIC_IWR1, 0);
+
+	bfin_write16(VR_CTL, val);
+	SSYNC();
+	asm("IDLE;");
+
+	bfin_write32(SIC_IWR0, iwr0);
+	bfin_write32(SIC_IWR1, iwr1);
+	local_irq_restore(flags);
+}
+#define bfin_read_PLL_STAT()			bfin_read16(PLL_STAT)
+#define bfin_write_PLL_STAT(val)		bfin_write16(PLL_STAT, val)
+#define bfin_read_PLL_LOCKCNT()			bfin_read16(PLL_LOCKCNT)
+#define bfin_write_PLL_LOCKCNT(val)		bfin_write16(PLL_LOCKCNT, val)
+#define bfin_read_CHIPID()			bfin_read32(CHIPID)
+#define bfin_write_CHIPID(val)			bfin_write32(CHIPID, val)
+
+
+/* System Interrupt Controller (0xFFC00100 - 0xFFC001FF)							*/
+#define bfin_read_SWRST()			bfin_read16(SWRST)
+#define bfin_write_SWRST(val)			bfin_write16(SWRST, val)
+#define bfin_read_SYSCR()			bfin_read16(SYSCR)
+#define bfin_write_SYSCR(val)			bfin_write16(SYSCR, val)
+
+#define bfin_read_SIC_RVECT()			bfin_read32(SIC_RVECT)
+#define bfin_write_SIC_RVECT(val)		bfin_write32(SIC_RVECT, val)
+#define bfin_read_SIC_IMASK0()			bfin_read32(SIC_IMASK0)
+#define bfin_write_SIC_IMASK0(val)		bfin_write32(SIC_IMASK0, val)
+#define bfin_read_SIC_IMASK(x)			bfin_read32(SIC_IMASK0 + (x << 6))
+#define bfin_write_SIC_IMASK(x, val)		bfin_write32((SIC_IMASK0 + (x << 6)), val)
+
+#define bfin_read_SIC_IAR0()			bfin_read32(SIC_IAR0)
+#define bfin_write_SIC_IAR0(val)		bfin_write32(SIC_IAR0, val)
+#define bfin_read_SIC_IAR1()			bfin_read32(SIC_IAR1)
+#define bfin_write_SIC_IAR1(val)		bfin_write32(SIC_IAR1, val)
+#define bfin_read_SIC_IAR2()			bfin_read32(SIC_IAR2)
+#define bfin_write_SIC_IAR2(val)		bfin_write32(SIC_IAR2, val)
+#define bfin_read_SIC_IAR3()			bfin_read32(SIC_IAR3)
+#define bfin_write_SIC_IAR3(val)		bfin_write32(SIC_IAR3, val)
+
+#define bfin_read_SIC_ISR0()			bfin_read32(SIC_ISR0)
+#define bfin_write_SIC_ISR0(val)		bfin_write32(SIC_ISR0, val)
+#define bfin_read_SIC_ISR(x)			bfin_read32(SIC_ISR0 + (x << 6))
+#define bfin_write_SIC_ISR(x, val)		bfin_write32((SIC_ISR0 + (x << 6)), val)
+
+#define bfin_read_SIC_IWR0()			bfin_read32(SIC_IWR0)
+#define bfin_write_SIC_IWR0(val)		bfin_write32(SIC_IWR0, val)
+#define bfin_read_SIC_IWR(x)			bfin_read32(SIC_IWR0 + (x << 6))
+#define bfin_write_SIC_IWR(x, val)		bfin_write32((SIC_IWR0 + (x << 6)), val)
+
+/* SIC Additions to ADSP-BF52x (0xFFC0014C - 0xFFC00162) */
+
+#define bfin_read_SIC_IMASK1()			bfin_read32(SIC_IMASK1)
+#define bfin_write_SIC_IMASK1(val)		bfin_write32(SIC_IMASK1, val)
+#define bfin_read_SIC_IAR4()			bfin_read32(SIC_IAR4)
+#define bfin_write_SIC_IAR4(val)		bfin_write32(SIC_IAR4, val)
+#define bfin_read_SIC_IAR5()			bfin_read32(SIC_IAR5)
+#define bfin_write_SIC_IAR5(val)		bfin_write32(SIC_IAR5, val)
+#define bfin_read_SIC_IAR6()			bfin_read32(SIC_IAR6)
+#define bfin_write_SIC_IAR6(val)		bfin_write32(SIC_IAR6, val)
+#define bfin_read_SIC_IAR7()			bfin_read32(SIC_IAR7)
+#define bfin_write_SIC_IAR7(val)		bfin_write32(SIC_IAR7, val)
+#define bfin_read_SIC_ISR1()			bfin_read32(SIC_ISR1)
+#define bfin_write_SIC_ISR1(val)		bfin_write32(SIC_ISR1, val)
+#define bfin_read_SIC_IWR1()			bfin_read32(SIC_IWR1)
+#define bfin_write_SIC_IWR1(val)		bfin_write32(SIC_IWR1, val)
+
+/* Watchdog Timer		(0xFFC00200 - 0xFFC002FF)									*/
+#define bfin_read_WDOG_CTL()			bfin_read16(WDOG_CTL)
+#define bfin_write_WDOG_CTL(val)		bfin_write16(WDOG_CTL, val)
+#define bfin_read_WDOG_CNT()			bfin_read32(WDOG_CNT)
+#define bfin_write_WDOG_CNT(val)		bfin_write32(WDOG_CNT, val)
+#define bfin_read_WDOG_STAT()			bfin_read32(WDOG_STAT)
+#define bfin_write_WDOG_STAT(val)		bfin_write32(WDOG_STAT, val)
+
+
+/* Real Time Clock		(0xFFC00300 - 0xFFC003FF)									*/
+#define bfin_read_RTC_STAT()			bfin_read32(RTC_STAT)
+#define bfin_write_RTC_STAT(val)		bfin_write32(RTC_STAT, val)
+#define bfin_read_RTC_ICTL()			bfin_read16(RTC_ICTL)
+#define bfin_write_RTC_ICTL(val)		bfin_write16(RTC_ICTL, val)
+#define bfin_read_RTC_ISTAT()			bfin_read16(RTC_ISTAT)
+#define bfin_write_RTC_ISTAT(val)		bfin_write16(RTC_ISTAT, val)
+#define bfin_read_RTC_SWCNT()			bfin_read16(RTC_SWCNT)
+#define bfin_write_RTC_SWCNT(val)		bfin_write16(RTC_SWCNT, val)
+#define bfin_read_RTC_ALARM()			bfin_read32(RTC_ALARM)
+#define bfin_write_RTC_ALARM(val)		bfin_write32(RTC_ALARM, val)
+#define bfin_read_RTC_FAST()			bfin_read16(RTC_FAST)
+#define bfin_write_RTC_FAST(val)		bfin_write16(RTC_FAST, val)
+#define bfin_read_RTC_PREN()			bfin_read16(RTC_PREN)
+#define bfin_write_RTC_PREN(val)		bfin_write16(RTC_PREN, val)
+
+
+/* UART0 Controller		(0xFFC00400 - 0xFFC004FF)									*/
+#define bfin_read_UART0_THR()			bfin_read16(UART0_THR)
+#define bfin_write_UART0_THR(val)		bfin_write16(UART0_THR, val)
+#define bfin_read_UART0_RBR()			bfin_read16(UART0_RBR)
+#define bfin_write_UART0_RBR(val)		bfin_write16(UART0_RBR, val)
+#define bfin_read_UART0_DLL()			bfin_read16(UART0_DLL)
+#define bfin_write_UART0_DLL(val)		bfin_write16(UART0_DLL, val)
+#define bfin_read_UART0_IER()			bfin_read16(UART0_IER)
+#define bfin_write_UART0_IER(val)		bfin_write16(UART0_IER, val)
+#define bfin_read_UART0_DLH()			bfin_read16(UART0_DLH)
+#define bfin_write_UART0_DLH(val)		bfin_write16(UART0_DLH, val)
+#define bfin_read_UART0_IIR()			bfin_read16(UART0_IIR)
+#define bfin_write_UART0_IIR(val)		bfin_write16(UART0_IIR, val)
+#define bfin_read_UART0_LCR()			bfin_read16(UART0_LCR)
+#define bfin_write_UART0_LCR(val)		bfin_write16(UART0_LCR, val)
+#define bfin_read_UART0_MCR()			bfin_read16(UART0_MCR)
+#define bfin_write_UART0_MCR(val)		bfin_write16(UART0_MCR, val)
+#define bfin_read_UART0_LSR()			bfin_read16(UART0_LSR)
+#define bfin_write_UART0_LSR(val)		bfin_write16(UART0_LSR, val)
+#define bfin_read_UART0_MSR()			bfin_read16(UART0_MSR)
+#define bfin_write_UART0_MSR(val)		bfin_write16(UART0_MSR, val)
+#define bfin_read_UART0_SCR()			bfin_read16(UART0_SCR)
+#define bfin_write_UART0_SCR(val)		bfin_write16(UART0_SCR, val)
+#define bfin_read_UART0_GCTL()			bfin_read16(UART0_GCTL)
+#define bfin_write_UART0_GCTL(val)		bfin_write16(UART0_GCTL, val)
+
+
+/* SPI Controller		(0xFFC00500 - 0xFFC005FF)									*/
+#define bfin_read_SPI_CTL()			bfin_read16(SPI_CTL)
+#define bfin_write_SPI_CTL(val)			bfin_write16(SPI_CTL, val)
+#define bfin_read_SPI_FLG()			bfin_read16(SPI_FLG)
+#define bfin_write_SPI_FLG(val)			bfin_write16(SPI_FLG, val)
+#define bfin_read_SPI_STAT()			bfin_read16(SPI_STAT)
+#define bfin_write_SPI_STAT(val)		bfin_write16(SPI_STAT, val)
+#define bfin_read_SPI_TDBR()			bfin_read16(SPI_TDBR)
+#define bfin_write_SPI_TDBR(val)		bfin_write16(SPI_TDBR, val)
+#define bfin_read_SPI_RDBR()			bfin_read16(SPI_RDBR)
+#define bfin_write_SPI_RDBR(val)		bfin_write16(SPI_RDBR, val)
+#define bfin_read_SPI_BAUD()			bfin_read16(SPI_BAUD)
+#define bfin_write_SPI_BAUD(val)		bfin_write16(SPI_BAUD, val)
+#define bfin_read_SPI_SHADOW()			bfin_read16(SPI_SHADOW)
+#define bfin_write_SPI_SHADOW(val)		bfin_write16(SPI_SHADOW, val)
+
+
+/* TIMER0-7 Registers		(0xFFC00600 - 0xFFC006FF)								*/
+#define bfin_read_TIMER0_CONFIG()		bfin_read16(TIMER0_CONFIG)
+#define bfin_write_TIMER0_CONFIG(val)		bfin_write16(TIMER0_CONFIG, val)
+#define bfin_read_TIMER0_COUNTER()		bfin_read32(TIMER0_COUNTER)
+#define bfin_write_TIMER0_COUNTER(val)		bfin_write32(TIMER0_COUNTER, val)
+#define bfin_read_TIMER0_PERIOD()		bfin_read32(TIMER0_PERIOD)
+#define bfin_write_TIMER0_PERIOD(val)		bfin_write32(TIMER0_PERIOD, val)
+#define bfin_read_TIMER0_WIDTH()		bfin_read32(TIMER0_WIDTH)
+#define bfin_write_TIMER0_WIDTH(val)		bfin_write32(TIMER0_WIDTH, val)
+
+#define bfin_read_TIMER1_CONFIG()		bfin_read16(TIMER1_CONFIG)
+#define bfin_write_TIMER1_CONFIG(val)		bfin_write16(TIMER1_CONFIG, val)
+#define bfin_read_TIMER1_COUNTER()		bfin_read32(TIMER1_COUNTER)
+#define bfin_write_TIMER1_COUNTER(val)		bfin_write32(TIMER1_COUNTER, val)
+#define bfin_read_TIMER1_PERIOD()		bfin_read32(TIMER1_PERIOD)
+#define bfin_write_TIMER1_PERIOD(val)		bfin_write32(TIMER1_PERIOD, val)
+#define bfin_read_TIMER1_WIDTH()		bfin_read32(TIMER1_WIDTH)
+#define bfin_write_TIMER1_WIDTH(val)		bfin_write32(TIMER1_WIDTH, val)
+
+#define bfin_read_TIMER2_CONFIG()		bfin_read16(TIMER2_CONFIG)
+#define bfin_write_TIMER2_CONFIG(val)		bfin_write16(TIMER2_CONFIG, val)
+#define bfin_read_TIMER2_COUNTER()		bfin_read32(TIMER2_COUNTER)
+#define bfin_write_TIMER2_COUNTER(val)		bfin_write32(TIMER2_COUNTER, val)
+#define bfin_read_TIMER2_PERIOD()		bfin_read32(TIMER2_PERIOD)
+#define bfin_write_TIMER2_PERIOD(val)		bfin_write32(TIMER2_PERIOD, val)
+#define bfin_read_TIMER2_WIDTH()		bfin_read32(TIMER2_WIDTH)
+#define bfin_write_TIMER2_WIDTH(val)		bfin_write32(TIMER2_WIDTH, val)
+
+#define bfin_read_TIMER3_CONFIG()		bfin_read16(TIMER3_CONFIG)
+#define bfin_write_TIMER3_CONFIG(val)		bfin_write16(TIMER3_CONFIG, val)
+#define bfin_read_TIMER3_COUNTER()		bfin_read32(TIMER3_COUNTER)
+#define bfin_write_TIMER3_COUNTER(val)		bfin_write32(TIMER3_COUNTER, val)
+#define bfin_read_TIMER3_PERIOD()		bfin_read32(TIMER3_PERIOD)
+#define bfin_write_TIMER3_PERIOD(val)		bfin_write32(TIMER3_PERIOD, val)
+#define bfin_read_TIMER3_WIDTH()		bfin_read32(TIMER3_WIDTH)
+#define bfin_write_TIMER3_WIDTH(val)		bfin_write32(TIMER3_WIDTH, val)
+
+#define bfin_read_TIMER4_CONFIG()		bfin_read16(TIMER4_CONFIG)
+#define bfin_write_TIMER4_CONFIG(val)		bfin_write16(TIMER4_CONFIG, val)
+#define bfin_read_TIMER4_COUNTER()		bfin_read32(TIMER4_COUNTER)
+#define bfin_write_TIMER4_COUNTER(val)		bfin_write32(TIMER4_COUNTER, val)
+#define bfin_read_TIMER4_PERIOD()		bfin_read32(TIMER4_PERIOD)
+#define bfin_write_TIMER4_PERIOD(val)		bfin_write32(TIMER4_PERIOD, val)
+#define bfin_read_TIMER4_WIDTH()		bfin_read32(TIMER4_WIDTH)
+#define bfin_write_TIMER4_WIDTH(val)		bfin_write32(TIMER4_WIDTH, val)
+
+#define bfin_read_TIMER5_CONFIG()		bfin_read16(TIMER5_CONFIG)
+#define bfin_write_TIMER5_CONFIG(val)		bfin_write16(TIMER5_CONFIG, val)
+#define bfin_read_TIMER5_COUNTER()		bfin_read32(TIMER5_COUNTER)
+#define bfin_write_TIMER5_COUNTER(val)		bfin_write32(TIMER5_COUNTER, val)
+#define bfin_read_TIMER5_PERIOD()		bfin_read32(TIMER5_PERIOD)
+#define bfin_write_TIMER5_PERIOD(val)		bfin_write32(TIMER5_PERIOD, val)
+#define bfin_read_TIMER5_WIDTH()		bfin_read32(TIMER5_WIDTH)
+#define bfin_write_TIMER5_WIDTH(val)		bfin_write32(TIMER5_WIDTH, val)
+
+#define bfin_read_TIMER6_CONFIG()		bfin_read16(TIMER6_CONFIG)
+#define bfin_write_TIMER6_CONFIG(val)		bfin_write16(TIMER6_CONFIG, val)
+#define bfin_read_TIMER6_COUNTER()		bfin_read32(TIMER6_COUNTER)
+#define bfin_write_TIMER6_COUNTER(val)		bfin_write32(TIMER6_COUNTER, val)
+#define bfin_read_TIMER6_PERIOD()		bfin_read32(TIMER6_PERIOD)
+#define bfin_write_TIMER6_PERIOD(val)		bfin_write32(TIMER6_PERIOD, val)
+#define bfin_read_TIMER6_WIDTH()		bfin_read32(TIMER6_WIDTH)
+#define bfin_write_TIMER6_WIDTH(val)		bfin_write32(TIMER6_WIDTH, val)
+
+#define bfin_read_TIMER7_CONFIG()		bfin_read16(TIMER7_CONFIG)
+#define bfin_write_TIMER7_CONFIG(val)		bfin_write16(TIMER7_CONFIG, val)
+#define bfin_read_TIMER7_COUNTER()		bfin_read32(TIMER7_COUNTER)
+#define bfin_write_TIMER7_COUNTER(val)		bfin_write32(TIMER7_COUNTER, val)
+#define bfin_read_TIMER7_PERIOD()		bfin_read32(TIMER7_PERIOD)
+#define bfin_write_TIMER7_PERIOD(val)		bfin_write32(TIMER7_PERIOD, val)
+#define bfin_read_TIMER7_WIDTH()		bfin_read32(TIMER7_WIDTH)
+#define bfin_write_TIMER7_WIDTH(val)		bfin_write32(TIMER7_WIDTH, val)
+
+#define bfin_read_TIMER_ENABLE()		bfin_read16(TIMER_ENABLE)
+#define bfin_write_TIMER_ENABLE(val)		bfin_write16(TIMER_ENABLE, val)
+#define bfin_read_TIMER_DISABLE()		bfin_read16(TIMER_DISABLE)
+#define bfin_write_TIMER_DISABLE(val)		bfin_write16(TIMER_DISABLE, val)
+#define bfin_read_TIMER_STATUS()		bfin_read32(TIMER_STATUS)
+#define bfin_write_TIMER_STATUS(val)		bfin_write32(TIMER_STATUS, val)
+
+
+/* General Purpose I/O Port F (0xFFC00700 - 0xFFC007FF)								*/
+#define bfin_read_PORTFIO()			bfin_read16(PORTFIO)
+#define bfin_write_PORTFIO(val)			bfin_write16(PORTFIO, val)
+#define bfin_read_PORTFIO_CLEAR()		bfin_read16(PORTFIO_CLEAR)
+#define bfin_write_PORTFIO_CLEAR(val)		bfin_write16(PORTFIO_CLEAR, val)
+#define bfin_read_PORTFIO_SET()			bfin_read16(PORTFIO_SET)
+#define bfin_write_PORTFIO_SET(val)		bfin_write16(PORTFIO_SET, val)
+#define bfin_read_PORTFIO_TOGGLE()		bfin_read16(PORTFIO_TOGGLE)
+#define bfin_write_PORTFIO_TOGGLE(val)		bfin_write16(PORTFIO_TOGGLE, val)
+#define bfin_read_PORTFIO_MASKA()		bfin_read16(PORTFIO_MASKA)
+#define bfin_write_PORTFIO_MASKA(val)		bfin_write16(PORTFIO_MASKA, val)
+#define bfin_read_PORTFIO_MASKA_CLEAR()		bfin_read16(PORTFIO_MASKA_CLEAR)
+#define bfin_write_PORTFIO_MASKA_CLEAR(val)	bfin_write16(PORTFIO_MASKA_CLEAR, val)
+#define bfin_read_PORTFIO_MASKA_SET()		bfin_read16(PORTFIO_MASKA_SET)
+#define bfin_write_PORTFIO_MASKA_SET(val)	bfin_write16(PORTFIO_MASKA_SET, val)
+#define bfin_read_PORTFIO_MASKA_TOGGLE()	bfin_read16(PORTFIO_MASKA_TOGGLE)
+#define bfin_write_PORTFIO_MASKA_TOGGLE(val)	bfin_write16(PORTFIO_MASKA_TOGGLE, val)
+#define bfin_read_PORTFIO_MASKB()		bfin_read16(PORTFIO_MASKB)
+#define bfin_write_PORTFIO_MASKB(val)		bfin_write16(PORTFIO_MASKB, val)
+#define bfin_read_PORTFIO_MASKB_CLEAR()		bfin_read16(PORTFIO_MASKB_CLEAR)
+#define bfin_write_PORTFIO_MASKB_CLEAR(val)	bfin_write16(PORTFIO_MASKB_CLEAR, val)
+#define bfin_read_PORTFIO_MASKB_SET()		bfin_read16(PORTFIO_MASKB_SET)
+#define bfin_write_PORTFIO_MASKB_SET(val)	bfin_write16(PORTFIO_MASKB_SET, val)
+#define bfin_read_PORTFIO_MASKB_TOGGLE()	bfin_read16(PORTFIO_MASKB_TOGGLE)
+#define bfin_write_PORTFIO_MASKB_TOGGLE(val)	bfin_write16(PORTFIO_MASKB_TOGGLE, val)
+#define bfin_read_PORTFIO_DIR()			bfin_read16(PORTFIO_DIR)
+#define bfin_write_PORTFIO_DIR(val)		bfin_write16(PORTFIO_DIR, val)
+#define bfin_read_PORTFIO_POLAR()		bfin_read16(PORTFIO_POLAR)
+#define bfin_write_PORTFIO_POLAR(val)		bfin_write16(PORTFIO_POLAR, val)
+#define bfin_read_PORTFIO_EDGE()		bfin_read16(PORTFIO_EDGE)
+#define bfin_write_PORTFIO_EDGE(val)		bfin_write16(PORTFIO_EDGE, val)
+#define bfin_read_PORTFIO_BOTH()		bfin_read16(PORTFIO_BOTH)
+#define bfin_write_PORTFIO_BOTH(val)		bfin_write16(PORTFIO_BOTH, val)
+#define bfin_read_PORTFIO_INEN()		bfin_read16(PORTFIO_INEN)
+#define bfin_write_PORTFIO_INEN(val)		bfin_write16(PORTFIO_INEN, val)
+
+
+/* SPORT0 Controller		(0xFFC00800 - 0xFFC008FF)								*/
+#define bfin_read_SPORT0_TCR1()			bfin_read16(SPORT0_TCR1)
+#define bfin_write_SPORT0_TCR1(val)		bfin_write16(SPORT0_TCR1, val)
+#define bfin_read_SPORT0_TCR2()			bfin_read16(SPORT0_TCR2)
+#define bfin_write_SPORT0_TCR2(val)		bfin_write16(SPORT0_TCR2, val)
+#define bfin_read_SPORT0_TCLKDIV()		bfin_read16(SPORT0_TCLKDIV)
+#define bfin_write_SPORT0_TCLKDIV(val)		bfin_write16(SPORT0_TCLKDIV, val)
+#define bfin_read_SPORT0_TFSDIV()		bfin_read16(SPORT0_TFSDIV)
+#define bfin_write_SPORT0_TFSDIV(val)		bfin_write16(SPORT0_TFSDIV, val)
+#define bfin_read_SPORT0_TX()			bfin_read32(SPORT0_TX)
+#define bfin_write_SPORT0_TX(val)		bfin_write32(SPORT0_TX, val)
+#define bfin_read_SPORT0_RX()			bfin_read32(SPORT0_RX)
+#define bfin_write_SPORT0_RX(val)		bfin_write32(SPORT0_RX, val)
+#define bfin_read_SPORT0_TX32()			bfin_read32(SPORT0_TX32)
+#define bfin_write_SPORT0_TX32(val)		bfin_write32(SPORT0_TX32, val)
+#define bfin_read_SPORT0_RX32()			bfin_read32(SPORT0_RX32)
+#define bfin_write_SPORT0_RX32(val)		bfin_write32(SPORT0_RX32, val)
+#define bfin_read_SPORT0_TX16()			bfin_read16(SPORT0_TX16)
+#define bfin_write_SPORT0_TX16(val)		bfin_write16(SPORT0_TX16, val)
+#define bfin_read_SPORT0_RX16()			bfin_read16(SPORT0_RX16)
+#define bfin_write_SPORT0_RX16(val)		bfin_write16(SPORT0_RX16, val)
+#define bfin_read_SPORT0_RCR1()			bfin_read16(SPORT0_RCR1)
+#define bfin_write_SPORT0_RCR1(val)		bfin_write16(SPORT0_RCR1, val)
+#define bfin_read_SPORT0_RCR2()			bfin_read16(SPORT0_RCR2)
+#define bfin_write_SPORT0_RCR2(val)		bfin_write16(SPORT0_RCR2, val)
+#define bfin_read_SPORT0_RCLKDIV()		bfin_read16(SPORT0_RCLKDIV)
+#define bfin_write_SPORT0_RCLKDIV(val)		bfin_write16(SPORT0_RCLKDIV, val)
+#define bfin_read_SPORT0_RFSDIV()		bfin_read16(SPORT0_RFSDIV)
+#define bfin_write_SPORT0_RFSDIV(val)		bfin_write16(SPORT0_RFSDIV, val)
+#define bfin_read_SPORT0_STAT()			bfin_read16(SPORT0_STAT)
+#define bfin_write_SPORT0_STAT(val)		bfin_write16(SPORT0_STAT, val)
+#define bfin_read_SPORT0_CHNL()			bfin_read16(SPORT0_CHNL)
+#define bfin_write_SPORT0_CHNL(val)		bfin_write16(SPORT0_CHNL, val)
+#define bfin_read_SPORT0_MCMC1()		bfin_read16(SPORT0_MCMC1)
+#define bfin_write_SPORT0_MCMC1(val)		bfin_write16(SPORT0_MCMC1, val)
+#define bfin_read_SPORT0_MCMC2()		bfin_read16(SPORT0_MCMC2)
+#define bfin_write_SPORT0_MCMC2(val)		bfin_write16(SPORT0_MCMC2, val)
+#define bfin_read_SPORT0_MTCS0()		bfin_read32(SPORT0_MTCS0)
+#define bfin_write_SPORT0_MTCS0(val)		bfin_write32(SPORT0_MTCS0, val)
+#define bfin_read_SPORT0_MTCS1()		bfin_read32(SPORT0_MTCS1)
+#define bfin_write_SPORT0_MTCS1(val)		bfin_write32(SPORT0_MTCS1, val)
+#define bfin_read_SPORT0_MTCS2()		bfin_read32(SPORT0_MTCS2)
+#define bfin_write_SPORT0_MTCS2(val)		bfin_write32(SPORT0_MTCS2, val)
+#define bfin_read_SPORT0_MTCS3()		bfin_read32(SPORT0_MTCS3)
+#define bfin_write_SPORT0_MTCS3(val)		bfin_write32(SPORT0_MTCS3, val)
+#define bfin_read_SPORT0_MRCS0()		bfin_read32(SPORT0_MRCS0)
+#define bfin_write_SPORT0_MRCS0(val)		bfin_write32(SPORT0_MRCS0, val)
+#define bfin_read_SPORT0_MRCS1()		bfin_read32(SPORT0_MRCS1)
+#define bfin_write_SPORT0_MRCS1(val)		bfin_write32(SPORT0_MRCS1, val)
+#define bfin_read_SPORT0_MRCS2()		bfin_read32(SPORT0_MRCS2)
+#define bfin_write_SPORT0_MRCS2(val)		bfin_write32(SPORT0_MRCS2, val)
+#define bfin_read_SPORT0_MRCS3()		bfin_read32(SPORT0_MRCS3)
+#define bfin_write_SPORT0_MRCS3(val)		bfin_write32(SPORT0_MRCS3, val)
+
+
+/* SPORT1 Controller		(0xFFC00900 - 0xFFC009FF)								*/
+#define bfin_read_SPORT1_TCR1()			bfin_read16(SPORT1_TCR1)
+#define bfin_write_SPORT1_TCR1(val)		bfin_write16(SPORT1_TCR1, val)
+#define bfin_read_SPORT1_TCR2()			bfin_read16(SPORT1_TCR2)
+#define bfin_write_SPORT1_TCR2(val)		bfin_write16(SPORT1_TCR2, val)
+#define bfin_read_SPORT1_TCLKDIV()		bfin_read16(SPORT1_TCLKDIV)
+#define bfin_write_SPORT1_TCLKDIV(val)		bfin_write16(SPORT1_TCLKDIV, val)
+#define bfin_read_SPORT1_TFSDIV()		bfin_read16(SPORT1_TFSDIV)
+#define bfin_write_SPORT1_TFSDIV(val)		bfin_write16(SPORT1_TFSDIV, val)
+#define bfin_read_SPORT1_TX()			bfin_read32(SPORT1_TX)
+#define bfin_write_SPORT1_TX(val)		bfin_write32(SPORT1_TX, val)
+#define bfin_read_SPORT1_RX()			bfin_read32(SPORT1_RX)
+#define bfin_write_SPORT1_RX(val)		bfin_write32(SPORT1_RX, val)
+#define bfin_read_SPORT1_TX32()			bfin_read32(SPORT1_TX32)
+#define bfin_write_SPORT1_TX32(val)		bfin_write32(SPORT1_TX32, val)
+#define bfin_read_SPORT1_RX32()			bfin_read32(SPORT1_RX32)
+#define bfin_write_SPORT1_RX32(val)		bfin_write32(SPORT1_RX32, val)
+#define bfin_read_SPORT1_TX16()			bfin_read16(SPORT1_TX16)
+#define bfin_write_SPORT1_TX16(val)		bfin_write16(SPORT1_TX16, val)
+#define bfin_read_SPORT1_RX16()			bfin_read16(SPORT1_RX16)
+#define bfin_write_SPORT1_RX16(val)		bfin_write16(SPORT1_RX16, val)
+#define bfin_read_SPORT1_RCR1()			bfin_read16(SPORT1_RCR1)
+#define bfin_write_SPORT1_RCR1(val)		bfin_write16(SPORT1_RCR1, val)
+#define bfin_read_SPORT1_RCR2()			bfin_read16(SPORT1_RCR2)
+#define bfin_write_SPORT1_RCR2(val)		bfin_write16(SPORT1_RCR2, val)
+#define bfin_read_SPORT1_RCLKDIV()		bfin_read16(SPORT1_RCLKDIV)
+#define bfin_write_SPORT1_RCLKDIV(val)		bfin_write16(SPORT1_RCLKDIV, val)
+#define bfin_read_SPORT1_RFSDIV()		bfin_read16(SPORT1_RFSDIV)
+#define bfin_write_SPORT1_RFSDIV(val)		bfin_write16(SPORT1_RFSDIV, val)
+#define bfin_read_SPORT1_STAT()			bfin_read16(SPORT1_STAT)
+#define bfin_write_SPORT1_STAT(val)		bfin_write16(SPORT1_STAT, val)
+#define bfin_read_SPORT1_CHNL()			bfin_read16(SPORT1_CHNL)
+#define bfin_write_SPORT1_CHNL(val)		bfin_write16(SPORT1_CHNL, val)
+#define bfin_read_SPORT1_MCMC1()		bfin_read16(SPORT1_MCMC1)
+#define bfin_write_SPORT1_MCMC1(val)		bfin_write16(SPORT1_MCMC1, val)
+#define bfin_read_SPORT1_MCMC2()		bfin_read16(SPORT1_MCMC2)
+#define bfin_write_SPORT1_MCMC2(val)		bfin_write16(SPORT1_MCMC2, val)
+#define bfin_read_SPORT1_MTCS0()		bfin_read32(SPORT1_MTCS0)
+#define bfin_write_SPORT1_MTCS0(val)		bfin_write32(SPORT1_MTCS0, val)
+#define bfin_read_SPORT1_MTCS1()		bfin_read32(SPORT1_MTCS1)
+#define bfin_write_SPORT1_MTCS1(val)		bfin_write32(SPORT1_MTCS1, val)
+#define bfin_read_SPORT1_MTCS2()		bfin_read32(SPORT1_MTCS2)
+#define bfin_write_SPORT1_MTCS2(val)		bfin_write32(SPORT1_MTCS2, val)
+#define bfin_read_SPORT1_MTCS3()		bfin_read32(SPORT1_MTCS3)
+#define bfin_write_SPORT1_MTCS3(val)		bfin_write32(SPORT1_MTCS3, val)
+#define bfin_read_SPORT1_MRCS0()		bfin_read32(SPORT1_MRCS0)
+#define bfin_write_SPORT1_MRCS0(val)		bfin_write32(SPORT1_MRCS0, val)
+#define bfin_read_SPORT1_MRCS1()		bfin_read32(SPORT1_MRCS1)
+#define bfin_write_SPORT1_MRCS1(val)		bfin_write32(SPORT1_MRCS1, val)
+#define bfin_read_SPORT1_MRCS2()		bfin_read32(SPORT1_MRCS2)
+#define bfin_write_SPORT1_MRCS2(val)		bfin_write32(SPORT1_MRCS2, val)
+#define bfin_read_SPORT1_MRCS3()		bfin_read32(SPORT1_MRCS3)
+#define bfin_write_SPORT1_MRCS3(val)		bfin_write32(SPORT1_MRCS3, val)
+
+
+/* External Bus Interface Unit (0xFFC00A00 - 0xFFC00AFF)							*/
+#define bfin_read_EBIU_AMGCTL()			bfin_read16(EBIU_AMGCTL)
+#define bfin_write_EBIU_AMGCTL(val)		bfin_write16(EBIU_AMGCTL, val)
+#define bfin_read_EBIU_AMBCTL0()		bfin_read32(EBIU_AMBCTL0)
+#define bfin_write_EBIU_AMBCTL0(val)		bfin_write32(EBIU_AMBCTL0, val)
+#define bfin_read_EBIU_AMBCTL1()		bfin_read32(EBIU_AMBCTL1)
+#define bfin_write_EBIU_AMBCTL1(val)		bfin_write32(EBIU_AMBCTL1, val)
+#define bfin_read_EBIU_SDGCTL()			bfin_read32(EBIU_SDGCTL)
+#define bfin_write_EBIU_SDGCTL(val)		bfin_write32(EBIU_SDGCTL, val)
+#define bfin_read_EBIU_SDBCTL()			bfin_read16(EBIU_SDBCTL)
+#define bfin_write_EBIU_SDBCTL(val)		bfin_write16(EBIU_SDBCTL, val)
+#define bfin_read_EBIU_SDRRC()			bfin_read16(EBIU_SDRRC)
+#define bfin_write_EBIU_SDRRC(val)		bfin_write16(EBIU_SDRRC, val)
+#define bfin_read_EBIU_SDSTAT()			bfin_read16(EBIU_SDSTAT)
+#define bfin_write_EBIU_SDSTAT(val)		bfin_write16(EBIU_SDSTAT, val)
+
+
+/* DMA Traffic Control Registers													*/
+#define bfin_read_DMA_TC_PER()			bfin_read16(DMA_TC_PER)
+#define bfin_write_DMA_TC_PER(val)		bfin_write16(DMA_TC_PER, val)
+#define bfin_read_DMA_TC_CNT()			bfin_read16(DMA_TC_CNT)
+#define bfin_write_DMA_TC_CNT(val)		bfin_write16(DMA_TC_CNT, val)
+
+/* Alternate deprecated register names (below) provided for backwards code compatibility */
+#define bfin_read_DMA_TCPER()			bfin_read16(DMA_TCPER)
+#define bfin_write_DMA_TCPER(val)		bfin_write16(DMA_TCPER, val)
+#define bfin_read_DMA_TCCNT()			bfin_read16(DMA_TCCNT)
+#define bfin_write_DMA_TCCNT(val)		bfin_write16(DMA_TCCNT, val)
+
+/* DMA Controller																	*/
+#define bfin_read_DMA0_CONFIG()			bfin_read16(DMA0_CONFIG)
+#define bfin_write_DMA0_CONFIG(val)		bfin_write16(DMA0_CONFIG, val)
+#define bfin_read_DMA0_NEXT_DESC_PTR()		bfin_read32(DMA0_NEXT_DESC_PTR)
+#define bfin_write_DMA0_NEXT_DESC_PTR(val)	bfin_write32(DMA0_NEXT_DESC_PTR, val)
+#define bfin_read_DMA0_START_ADDR()		bfin_read32(DMA0_START_ADDR)
+#define bfin_write_DMA0_START_ADDR(val)		bfin_write32(DMA0_START_ADDR, val)
+#define bfin_read_DMA0_X_COUNT()		bfin_read16(DMA0_X_COUNT)
+#define bfin_write_DMA0_X_COUNT(val)		bfin_write16(DMA0_X_COUNT, val)
+#define bfin_read_DMA0_Y_COUNT()		bfin_read16(DMA0_Y_COUNT)
+#define bfin_write_DMA0_Y_COUNT(val)		bfin_write16(DMA0_Y_COUNT, val)
+#define bfin_read_DMA0_X_MODIFY()		bfin_read16(DMA0_X_MODIFY)
+#define bfin_write_DMA0_X_MODIFY(val)		bfin_write16(DMA0_X_MODIFY, val)
+#define bfin_read_DMA0_Y_MODIFY()		bfin_read16(DMA0_Y_MODIFY)
+#define bfin_write_DMA0_Y_MODIFY(val)		bfin_write16(DMA0_Y_MODIFY, val)
+#define bfin_read_DMA0_CURR_DESC_PTR()		bfin_read32(DMA0_CURR_DESC_PTR)
+#define bfin_write_DMA0_CURR_DESC_PTR(val)	bfin_write32(DMA0_CURR_DESC_PTR, val)
+#define bfin_read_DMA0_CURR_ADDR()		bfin_read32(DMA0_CURR_ADDR)
+#define bfin_write_DMA0_CURR_ADDR(val)		bfin_write32(DMA0_CURR_ADDR, val)
+#define bfin_read_DMA0_CURR_X_COUNT()		bfin_read16(DMA0_CURR_X_COUNT)
+#define bfin_write_DMA0_CURR_X_COUNT(val)	bfin_write16(DMA0_CURR_X_COUNT, val)
+#define bfin_read_DMA0_CURR_Y_COUNT()		bfin_read16(DMA0_CURR_Y_COUNT)
+#define bfin_write_DMA0_CURR_Y_COUNT(val)	bfin_write16(DMA0_CURR_Y_COUNT, val)
+#define bfin_read_DMA0_IRQ_STATUS()		bfin_read16(DMA0_IRQ_STATUS)
+#define bfin_write_DMA0_IRQ_STATUS(val)		bfin_write16(DMA0_IRQ_STATUS, val)
+#define bfin_read_DMA0_PERIPHERAL_MAP()		bfin_read16(DMA0_PERIPHERAL_MAP)
+#define bfin_write_DMA0_PERIPHERAL_MAP(val)	bfin_write16(DMA0_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA1_CONFIG()			bfin_read16(DMA1_CONFIG)
+#define bfin_write_DMA1_CONFIG(val)		bfin_write16(DMA1_CONFIG, val)
+#define bfin_read_DMA1_NEXT_DESC_PTR()		bfin_read32(DMA1_NEXT_DESC_PTR)
+#define bfin_write_DMA1_NEXT_DESC_PTR(val)	bfin_write32(DMA1_NEXT_DESC_PTR, val)
+#define bfin_read_DMA1_START_ADDR()		bfin_read32(DMA1_START_ADDR)
+#define bfin_write_DMA1_START_ADDR(val)		bfin_write32(DMA1_START_ADDR, val)
+#define bfin_read_DMA1_X_COUNT()		bfin_read16(DMA1_X_COUNT)
+#define bfin_write_DMA1_X_COUNT(val)		bfin_write16(DMA1_X_COUNT, val)
+#define bfin_read_DMA1_Y_COUNT()		bfin_read16(DMA1_Y_COUNT)
+#define bfin_write_DMA1_Y_COUNT(val)		bfin_write16(DMA1_Y_COUNT, val)
+#define bfin_read_DMA1_X_MODIFY()		bfin_read16(DMA1_X_MODIFY)
+#define bfin_write_DMA1_X_MODIFY(val)		bfin_write16(DMA1_X_MODIFY, val)
+#define bfin_read_DMA1_Y_MODIFY()		bfin_read16(DMA1_Y_MODIFY)
+#define bfin_write_DMA1_Y_MODIFY(val)		bfin_write16(DMA1_Y_MODIFY, val)
+#define bfin_read_DMA1_CURR_DESC_PTR()		bfin_read32(DMA1_CURR_DESC_PTR)
+#define bfin_write_DMA1_CURR_DESC_PTR(val)	bfin_write32(DMA1_CURR_DESC_PTR, val)
+#define bfin_read_DMA1_CURR_ADDR()		bfin_read32(DMA1_CURR_ADDR)
+#define bfin_write_DMA1_CURR_ADDR(val)		bfin_write32(DMA1_CURR_ADDR, val)
+#define bfin_read_DMA1_CURR_X_COUNT()		bfin_read16(DMA1_CURR_X_COUNT)
+#define bfin_write_DMA1_CURR_X_COUNT(val)	bfin_write16(DMA1_CURR_X_COUNT, val)
+#define bfin_read_DMA1_CURR_Y_COUNT()		bfin_read16(DMA1_CURR_Y_COUNT)
+#define bfin_write_DMA1_CURR_Y_COUNT(val)	bfin_write16(DMA1_CURR_Y_COUNT, val)
+#define bfin_read_DMA1_IRQ_STATUS()		bfin_read16(DMA1_IRQ_STATUS)
+#define bfin_write_DMA1_IRQ_STATUS(val)		bfin_write16(DMA1_IRQ_STATUS, val)
+#define bfin_read_DMA1_PERIPHERAL_MAP()		bfin_read16(DMA1_PERIPHERAL_MAP)
+#define bfin_write_DMA1_PERIPHERAL_MAP(val)	bfin_write16(DMA1_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA2_CONFIG()			bfin_read16(DMA2_CONFIG)
+#define bfin_write_DMA2_CONFIG(val)		bfin_write16(DMA2_CONFIG, val)
+#define bfin_read_DMA2_NEXT_DESC_PTR()		bfin_read32(DMA2_NEXT_DESC_PTR)
+#define bfin_write_DMA2_NEXT_DESC_PTR(val)	bfin_write32(DMA2_NEXT_DESC_PTR, val)
+#define bfin_read_DMA2_START_ADDR()		bfin_read32(DMA2_START_ADDR)
+#define bfin_write_DMA2_START_ADDR(val)		bfin_write32(DMA2_START_ADDR, val)
+#define bfin_read_DMA2_X_COUNT()		bfin_read16(DMA2_X_COUNT)
+#define bfin_write_DMA2_X_COUNT(val)		bfin_write16(DMA2_X_COUNT, val)
+#define bfin_read_DMA2_Y_COUNT()		bfin_read16(DMA2_Y_COUNT)
+#define bfin_write_DMA2_Y_COUNT(val)		bfin_write16(DMA2_Y_COUNT, val)
+#define bfin_read_DMA2_X_MODIFY()		bfin_read16(DMA2_X_MODIFY)
+#define bfin_write_DMA2_X_MODIFY(val)		bfin_write16(DMA2_X_MODIFY, val)
+#define bfin_read_DMA2_Y_MODIFY()		bfin_read16(DMA2_Y_MODIFY)
+#define bfin_write_DMA2_Y_MODIFY(val)		bfin_write16(DMA2_Y_MODIFY, val)
+#define bfin_read_DMA2_CURR_DESC_PTR()		bfin_read32(DMA2_CURR_DESC_PTR)
+#define bfin_write_DMA2_CURR_DESC_PTR(val)	bfin_write32(DMA2_CURR_DESC_PTR, val)
+#define bfin_read_DMA2_CURR_ADDR()		bfin_read32(DMA2_CURR_ADDR)
+#define bfin_write_DMA2_CURR_ADDR(val)		bfin_write32(DMA2_CURR_ADDR, val)
+#define bfin_read_DMA2_CURR_X_COUNT()		bfin_read16(DMA2_CURR_X_COUNT)
+#define bfin_write_DMA2_CURR_X_COUNT(val)	bfin_write16(DMA2_CURR_X_COUNT, val)
+#define bfin_read_DMA2_CURR_Y_COUNT()		bfin_read16(DMA2_CURR_Y_COUNT)
+#define bfin_write_DMA2_CURR_Y_COUNT(val)	bfin_write16(DMA2_CURR_Y_COUNT, val)
+#define bfin_read_DMA2_IRQ_STATUS()		bfin_read16(DMA2_IRQ_STATUS)
+#define bfin_write_DMA2_IRQ_STATUS(val)		bfin_write16(DMA2_IRQ_STATUS, val)
+#define bfin_read_DMA2_PERIPHERAL_MAP()		bfin_read16(DMA2_PERIPHERAL_MAP)
+#define bfin_write_DMA2_PERIPHERAL_MAP(val)	bfin_write16(DMA2_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA3_CONFIG()			bfin_read16(DMA3_CONFIG)
+#define bfin_write_DMA3_CONFIG(val)		bfin_write16(DMA3_CONFIG, val)
+#define bfin_read_DMA3_NEXT_DESC_PTR()		bfin_read32(DMA3_NEXT_DESC_PTR)
+#define bfin_write_DMA3_NEXT_DESC_PTR(val)	bfin_write32(DMA3_NEXT_DESC_PTR, val)
+#define bfin_read_DMA3_START_ADDR()		bfin_read32(DMA3_START_ADDR)
+#define bfin_write_DMA3_START_ADDR(val)		bfin_write32(DMA3_START_ADDR, val)
+#define bfin_read_DMA3_X_COUNT()		bfin_read16(DMA3_X_COUNT)
+#define bfin_write_DMA3_X_COUNT(val)		bfin_write16(DMA3_X_COUNT, val)
+#define bfin_read_DMA3_Y_COUNT()		bfin_read16(DMA3_Y_COUNT)
+#define bfin_write_DMA3_Y_COUNT(val)		bfin_write16(DMA3_Y_COUNT, val)
+#define bfin_read_DMA3_X_MODIFY()		bfin_read16(DMA3_X_MODIFY)
+#define bfin_write_DMA3_X_MODIFY(val)		bfin_write16(DMA3_X_MODIFY, val)
+#define bfin_read_DMA3_Y_MODIFY()		bfin_read16(DMA3_Y_MODIFY)
+#define bfin_write_DMA3_Y_MODIFY(val)		bfin_write16(DMA3_Y_MODIFY, val)
+#define bfin_read_DMA3_CURR_DESC_PTR()		bfin_read32(DMA3_CURR_DESC_PTR)
+#define bfin_write_DMA3_CURR_DESC_PTR(val)	bfin_write32(DMA3_CURR_DESC_PTR, val)
+#define bfin_read_DMA3_CURR_ADDR()		bfin_read32(DMA3_CURR_ADDR)
+#define bfin_write_DMA3_CURR_ADDR(val)		bfin_write32(DMA3_CURR_ADDR, val)
+#define bfin_read_DMA3_CURR_X_COUNT()		bfin_read16(DMA3_CURR_X_COUNT)
+#define bfin_write_DMA3_CURR_X_COUNT(val)	bfin_write16(DMA3_CURR_X_COUNT, val)
+#define bfin_read_DMA3_CURR_Y_COUNT()		bfin_read16(DMA3_CURR_Y_COUNT)
+#define bfin_write_DMA3_CURR_Y_COUNT(val)	bfin_write16(DMA3_CURR_Y_COUNT, val)
+#define bfin_read_DMA3_IRQ_STATUS()		bfin_read16(DMA3_IRQ_STATUS)
+#define bfin_write_DMA3_IRQ_STATUS(val)		bfin_write16(DMA3_IRQ_STATUS, val)
+#define bfin_read_DMA3_PERIPHERAL_MAP()		bfin_read16(DMA3_PERIPHERAL_MAP)
+#define bfin_write_DMA3_PERIPHERAL_MAP(val)	bfin_write16(DMA3_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA4_CONFIG()			bfin_read16(DMA4_CONFIG)
+#define bfin_write_DMA4_CONFIG(val)		bfin_write16(DMA4_CONFIG, val)
+#define bfin_read_DMA4_NEXT_DESC_PTR()		bfin_read32(DMA4_NEXT_DESC_PTR)
+#define bfin_write_DMA4_NEXT_DESC_PTR(val)	bfin_write32(DMA4_NEXT_DESC_PTR, val)
+#define bfin_read_DMA4_START_ADDR()		bfin_read32(DMA4_START_ADDR)
+#define bfin_write_DMA4_START_ADDR(val)		bfin_write32(DMA4_START_ADDR, val)
+#define bfin_read_DMA4_X_COUNT()		bfin_read16(DMA4_X_COUNT)
+#define bfin_write_DMA4_X_COUNT(val)		bfin_write16(DMA4_X_COUNT, val)
+#define bfin_read_DMA4_Y_COUNT()		bfin_read16(DMA4_Y_COUNT)
+#define bfin_write_DMA4_Y_COUNT(val)		bfin_write16(DMA4_Y_COUNT, val)
+#define bfin_read_DMA4_X_MODIFY()		bfin_read16(DMA4_X_MODIFY)
+#define bfin_write_DMA4_X_MODIFY(val)		bfin_write16(DMA4_X_MODIFY, val)
+#define bfin_read_DMA4_Y_MODIFY()		bfin_read16(DMA4_Y_MODIFY)
+#define bfin_write_DMA4_Y_MODIFY(val)		bfin_write16(DMA4_Y_MODIFY, val)
+#define bfin_read_DMA4_CURR_DESC_PTR()		bfin_read32(DMA4_CURR_DESC_PTR)
+#define bfin_write_DMA4_CURR_DESC_PTR(val)	bfin_write32(DMA4_CURR_DESC_PTR, val)
+#define bfin_read_DMA4_CURR_ADDR()		bfin_read32(DMA4_CURR_ADDR)
+#define bfin_write_DMA4_CURR_ADDR(val)		bfin_write32(DMA4_CURR_ADDR, val)
+#define bfin_read_DMA4_CURR_X_COUNT()		bfin_read16(DMA4_CURR_X_COUNT)
+#define bfin_write_DMA4_CURR_X_COUNT(val)	bfin_write16(DMA4_CURR_X_COUNT, val)
+#define bfin_read_DMA4_CURR_Y_COUNT()		bfin_read16(DMA4_CURR_Y_COUNT)
+#define bfin_write_DMA4_CURR_Y_COUNT(val)	bfin_write16(DMA4_CURR_Y_COUNT, val)
+#define bfin_read_DMA4_IRQ_STATUS()		bfin_read16(DMA4_IRQ_STATUS)
+#define bfin_write_DMA4_IRQ_STATUS(val)		bfin_write16(DMA4_IRQ_STATUS, val)
+#define bfin_read_DMA4_PERIPHERAL_MAP()		bfin_read16(DMA4_PERIPHERAL_MAP)
+#define bfin_write_DMA4_PERIPHERAL_MAP(val)	bfin_write16(DMA4_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA5_CONFIG()			bfin_read16(DMA5_CONFIG)
+#define bfin_write_DMA5_CONFIG(val)		bfin_write16(DMA5_CONFIG, val)
+#define bfin_read_DMA5_NEXT_DESC_PTR()		bfin_read32(DMA5_NEXT_DESC_PTR)
+#define bfin_write_DMA5_NEXT_DESC_PTR(val)	bfin_write32(DMA5_NEXT_DESC_PTR, val)
+#define bfin_read_DMA5_START_ADDR()		bfin_read32(DMA5_START_ADDR)
+#define bfin_write_DMA5_START_ADDR(val)		bfin_write32(DMA5_START_ADDR, val)
+#define bfin_read_DMA5_X_COUNT()		bfin_read16(DMA5_X_COUNT)
+#define bfin_write_DMA5_X_COUNT(val)		bfin_write16(DMA5_X_COUNT, val)
+#define bfin_read_DMA5_Y_COUNT()		bfin_read16(DMA5_Y_COUNT)
+#define bfin_write_DMA5_Y_COUNT(val)		bfin_write16(DMA5_Y_COUNT, val)
+#define bfin_read_DMA5_X_MODIFY()		bfin_read16(DMA5_X_MODIFY)
+#define bfin_write_DMA5_X_MODIFY(val)		bfin_write16(DMA5_X_MODIFY, val)
+#define bfin_read_DMA5_Y_MODIFY()		bfin_read16(DMA5_Y_MODIFY)
+#define bfin_write_DMA5_Y_MODIFY(val)		bfin_write16(DMA5_Y_MODIFY, val)
+#define bfin_read_DMA5_CURR_DESC_PTR()		bfin_read32(DMA5_CURR_DESC_PTR)
+#define bfin_write_DMA5_CURR_DESC_PTR(val)	bfin_write32(DMA5_CURR_DESC_PTR, val)
+#define bfin_read_DMA5_CURR_ADDR()		bfin_read32(DMA5_CURR_ADDR)
+#define bfin_write_DMA5_CURR_ADDR(val)		bfin_write32(DMA5_CURR_ADDR, val)
+#define bfin_read_DMA5_CURR_X_COUNT()		bfin_read16(DMA5_CURR_X_COUNT)
+#define bfin_write_DMA5_CURR_X_COUNT(val)	bfin_write16(DMA5_CURR_X_COUNT, val)
+#define bfin_read_DMA5_CURR_Y_COUNT()		bfin_read16(DMA5_CURR_Y_COUNT)
+#define bfin_write_DMA5_CURR_Y_COUNT(val)	bfin_write16(DMA5_CURR_Y_COUNT, val)
+#define bfin_read_DMA5_IRQ_STATUS()		bfin_read16(DMA5_IRQ_STATUS)
+#define bfin_write_DMA5_IRQ_STATUS(val)		bfin_write16(DMA5_IRQ_STATUS, val)
+#define bfin_read_DMA5_PERIPHERAL_MAP()		bfin_read16(DMA5_PERIPHERAL_MAP)
+#define bfin_write_DMA5_PERIPHERAL_MAP(val)	bfin_write16(DMA5_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA6_CONFIG()			bfin_read16(DMA6_CONFIG)
+#define bfin_write_DMA6_CONFIG(val)		bfin_write16(DMA6_CONFIG, val)
+#define bfin_read_DMA6_NEXT_DESC_PTR()		bfin_read32(DMA6_NEXT_DESC_PTR)
+#define bfin_write_DMA6_NEXT_DESC_PTR(val)	bfin_write32(DMA6_NEXT_DESC_PTR, val)
+#define bfin_read_DMA6_START_ADDR()		bfin_read32(DMA6_START_ADDR)
+#define bfin_write_DMA6_START_ADDR(val)		bfin_write32(DMA6_START_ADDR, val)
+#define bfin_read_DMA6_X_COUNT()		bfin_read16(DMA6_X_COUNT)
+#define bfin_write_DMA6_X_COUNT(val)		bfin_write16(DMA6_X_COUNT, val)
+#define bfin_read_DMA6_Y_COUNT()		bfin_read16(DMA6_Y_COUNT)
+#define bfin_write_DMA6_Y_COUNT(val)		bfin_write16(DMA6_Y_COUNT, val)
+#define bfin_read_DMA6_X_MODIFY()		bfin_read16(DMA6_X_MODIFY)
+#define bfin_write_DMA6_X_MODIFY(val)		bfin_write16(DMA6_X_MODIFY, val)
+#define bfin_read_DMA6_Y_MODIFY()		bfin_read16(DMA6_Y_MODIFY)
+#define bfin_write_DMA6_Y_MODIFY(val)		bfin_write16(DMA6_Y_MODIFY, val)
+#define bfin_read_DMA6_CURR_DESC_PTR()		bfin_read32(DMA6_CURR_DESC_PTR)
+#define bfin_write_DMA6_CURR_DESC_PTR(val)	bfin_write32(DMA6_CURR_DESC_PTR, val)
+#define bfin_read_DMA6_CURR_ADDR()		bfin_read32(DMA6_CURR_ADDR)
+#define bfin_write_DMA6_CURR_ADDR(val)		bfin_write32(DMA6_CURR_ADDR, val)
+#define bfin_read_DMA6_CURR_X_COUNT()		bfin_read16(DMA6_CURR_X_COUNT)
+#define bfin_write_DMA6_CURR_X_COUNT(val)	bfin_write16(DMA6_CURR_X_COUNT, val)
+#define bfin_read_DMA6_CURR_Y_COUNT()		bfin_read16(DMA6_CURR_Y_COUNT)
+#define bfin_write_DMA6_CURR_Y_COUNT(val)	bfin_write16(DMA6_CURR_Y_COUNT, val)
+#define bfin_read_DMA6_IRQ_STATUS()		bfin_read16(DMA6_IRQ_STATUS)
+#define bfin_write_DMA6_IRQ_STATUS(val)		bfin_write16(DMA6_IRQ_STATUS, val)
+#define bfin_read_DMA6_PERIPHERAL_MAP()		bfin_read16(DMA6_PERIPHERAL_MAP)
+#define bfin_write_DMA6_PERIPHERAL_MAP(val)	bfin_write16(DMA6_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA7_CONFIG()			bfin_read16(DMA7_CONFIG)
+#define bfin_write_DMA7_CONFIG(val)		bfin_write16(DMA7_CONFIG, val)
+#define bfin_read_DMA7_NEXT_DESC_PTR()		bfin_read32(DMA7_NEXT_DESC_PTR)
+#define bfin_write_DMA7_NEXT_DESC_PTR(val)	bfin_write32(DMA7_NEXT_DESC_PTR, val)
+#define bfin_read_DMA7_START_ADDR()		bfin_read32(DMA7_START_ADDR)
+#define bfin_write_DMA7_START_ADDR(val)		bfin_write32(DMA7_START_ADDR, val)
+#define bfin_read_DMA7_X_COUNT()		bfin_read16(DMA7_X_COUNT)
+#define bfin_write_DMA7_X_COUNT(val)		bfin_write16(DMA7_X_COUNT, val)
+#define bfin_read_DMA7_Y_COUNT()		bfin_read16(DMA7_Y_COUNT)
+#define bfin_write_DMA7_Y_COUNT(val)		bfin_write16(DMA7_Y_COUNT, val)
+#define bfin_read_DMA7_X_MODIFY()		bfin_read16(DMA7_X_MODIFY)
+#define bfin_write_DMA7_X_MODIFY(val)		bfin_write16(DMA7_X_MODIFY, val)
+#define bfin_read_DMA7_Y_MODIFY()		bfin_read16(DMA7_Y_MODIFY)
+#define bfin_write_DMA7_Y_MODIFY(val)		bfin_write16(DMA7_Y_MODIFY, val)
+#define bfin_read_DMA7_CURR_DESC_PTR()		bfin_read32(DMA7_CURR_DESC_PTR)
+#define bfin_write_DMA7_CURR_DESC_PTR(val)	bfin_write32(DMA7_CURR_DESC_PTR, val)
+#define bfin_read_DMA7_CURR_ADDR()		bfin_read32(DMA7_CURR_ADDR)
+#define bfin_write_DMA7_CURR_ADDR(val)		bfin_write32(DMA7_CURR_ADDR, val)
+#define bfin_read_DMA7_CURR_X_COUNT()		bfin_read16(DMA7_CURR_X_COUNT)
+#define bfin_write_DMA7_CURR_X_COUNT(val)	bfin_write16(DMA7_CURR_X_COUNT, val)
+#define bfin_read_DMA7_CURR_Y_COUNT()		bfin_read16(DMA7_CURR_Y_COUNT)
+#define bfin_write_DMA7_CURR_Y_COUNT(val)	bfin_write16(DMA7_CURR_Y_COUNT, val)
+#define bfin_read_DMA7_IRQ_STATUS()		bfin_read16(DMA7_IRQ_STATUS)
+#define bfin_write_DMA7_IRQ_STATUS(val)		bfin_write16(DMA7_IRQ_STATUS, val)
+#define bfin_read_DMA7_PERIPHERAL_MAP()		bfin_read16(DMA7_PERIPHERAL_MAP)
+#define bfin_write_DMA7_PERIPHERAL_MAP(val)	bfin_write16(DMA7_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA8_CONFIG()			bfin_read16(DMA8_CONFIG)
+#define bfin_write_DMA8_CONFIG(val)		bfin_write16(DMA8_CONFIG, val)
+#define bfin_read_DMA8_NEXT_DESC_PTR()		bfin_read32(DMA8_NEXT_DESC_PTR)
+#define bfin_write_DMA8_NEXT_DESC_PTR(val)	bfin_write32(DMA8_NEXT_DESC_PTR, val)
+#define bfin_read_DMA8_START_ADDR()		bfin_read32(DMA8_START_ADDR)
+#define bfin_write_DMA8_START_ADDR(val)		bfin_write32(DMA8_START_ADDR, val)
+#define bfin_read_DMA8_X_COUNT()		bfin_read16(DMA8_X_COUNT)
+#define bfin_write_DMA8_X_COUNT(val)		bfin_write16(DMA8_X_COUNT, val)
+#define bfin_read_DMA8_Y_COUNT()		bfin_read16(DMA8_Y_COUNT)
+#define bfin_write_DMA8_Y_COUNT(val)		bfin_write16(DMA8_Y_COUNT, val)
+#define bfin_read_DMA8_X_MODIFY()		bfin_read16(DMA8_X_MODIFY)
+#define bfin_write_DMA8_X_MODIFY(val)		bfin_write16(DMA8_X_MODIFY, val)
+#define bfin_read_DMA8_Y_MODIFY()		bfin_read16(DMA8_Y_MODIFY)
+#define bfin_write_DMA8_Y_MODIFY(val)		bfin_write16(DMA8_Y_MODIFY, val)
+#define bfin_read_DMA8_CURR_DESC_PTR()		bfin_read32(DMA8_CURR_DESC_PTR)
+#define bfin_write_DMA8_CURR_DESC_PTR(val)	bfin_write32(DMA8_CURR_DESC_PTR, val)
+#define bfin_read_DMA8_CURR_ADDR()		bfin_read32(DMA8_CURR_ADDR)
+#define bfin_write_DMA8_CURR_ADDR(val)		bfin_write32(DMA8_CURR_ADDR, val)
+#define bfin_read_DMA8_CURR_X_COUNT()		bfin_read16(DMA8_CURR_X_COUNT)
+#define bfin_write_DMA8_CURR_X_COUNT(val)	bfin_write16(DMA8_CURR_X_COUNT, val)
+#define bfin_read_DMA8_CURR_Y_COUNT()		bfin_read16(DMA8_CURR_Y_COUNT)
+#define bfin_write_DMA8_CURR_Y_COUNT(val)	bfin_write16(DMA8_CURR_Y_COUNT, val)
+#define bfin_read_DMA8_IRQ_STATUS()		bfin_read16(DMA8_IRQ_STATUS)
+#define bfin_write_DMA8_IRQ_STATUS(val)		bfin_write16(DMA8_IRQ_STATUS, val)
+#define bfin_read_DMA8_PERIPHERAL_MAP()		bfin_read16(DMA8_PERIPHERAL_MAP)
+#define bfin_write_DMA8_PERIPHERAL_MAP(val)	bfin_write16(DMA8_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA9_CONFIG()			bfin_read16(DMA9_CONFIG)
+#define bfin_write_DMA9_CONFIG(val)		bfin_write16(DMA9_CONFIG, val)
+#define bfin_read_DMA9_NEXT_DESC_PTR()		bfin_read32(DMA9_NEXT_DESC_PTR)
+#define bfin_write_DMA9_NEXT_DESC_PTR(val)	bfin_write32(DMA9_NEXT_DESC_PTR, val)
+#define bfin_read_DMA9_START_ADDR()		bfin_read32(DMA9_START_ADDR)
+#define bfin_write_DMA9_START_ADDR(val)		bfin_write32(DMA9_START_ADDR, val)
+#define bfin_read_DMA9_X_COUNT()		bfin_read16(DMA9_X_COUNT)
+#define bfin_write_DMA9_X_COUNT(val)		bfin_write16(DMA9_X_COUNT, val)
+#define bfin_read_DMA9_Y_COUNT()		bfin_read16(DMA9_Y_COUNT)
+#define bfin_write_DMA9_Y_COUNT(val)		bfin_write16(DMA9_Y_COUNT, val)
+#define bfin_read_DMA9_X_MODIFY()		bfin_read16(DMA9_X_MODIFY)
+#define bfin_write_DMA9_X_MODIFY(val)		bfin_write16(DMA9_X_MODIFY, val)
+#define bfin_read_DMA9_Y_MODIFY()		bfin_read16(DMA9_Y_MODIFY)
+#define bfin_write_DMA9_Y_MODIFY(val)		bfin_write16(DMA9_Y_MODIFY, val)
+#define bfin_read_DMA9_CURR_DESC_PTR()		bfin_read32(DMA9_CURR_DESC_PTR)
+#define bfin_write_DMA9_CURR_DESC_PTR(val)	bfin_write32(DMA9_CURR_DESC_PTR, val)
+#define bfin_read_DMA9_CURR_ADDR()		bfin_read32(DMA9_CURR_ADDR)
+#define bfin_write_DMA9_CURR_ADDR(val)		bfin_write32(DMA9_CURR_ADDR, val)
+#define bfin_read_DMA9_CURR_X_COUNT()		bfin_read16(DMA9_CURR_X_COUNT)
+#define bfin_write_DMA9_CURR_X_COUNT(val)	bfin_write16(DMA9_CURR_X_COUNT, val)
+#define bfin_read_DMA9_CURR_Y_COUNT()		bfin_read16(DMA9_CURR_Y_COUNT)
+#define bfin_write_DMA9_CURR_Y_COUNT(val)	bfin_write16(DMA9_CURR_Y_COUNT, val)
+#define bfin_read_DMA9_IRQ_STATUS()		bfin_read16(DMA9_IRQ_STATUS)
+#define bfin_write_DMA9_IRQ_STATUS(val)		bfin_write16(DMA9_IRQ_STATUS, val)
+#define bfin_read_DMA9_PERIPHERAL_MAP()		bfin_read16(DMA9_PERIPHERAL_MAP)
+#define bfin_write_DMA9_PERIPHERAL_MAP(val)	bfin_write16(DMA9_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA10_CONFIG()		bfin_read16(DMA10_CONFIG)
+#define bfin_write_DMA10_CONFIG(val)		bfin_write16(DMA10_CONFIG, val)
+#define bfin_read_DMA10_NEXT_DESC_PTR()		bfin_read32(DMA10_NEXT_DESC_PTR)
+#define bfin_write_DMA10_NEXT_DESC_PTR(val)	bfin_write32(DMA10_NEXT_DESC_PTR, val)
+#define bfin_read_DMA10_START_ADDR()		bfin_read32(DMA10_START_ADDR)
+#define bfin_write_DMA10_START_ADDR(val)	bfin_write32(DMA10_START_ADDR, val)
+#define bfin_read_DMA10_X_COUNT()		bfin_read16(DMA10_X_COUNT)
+#define bfin_write_DMA10_X_COUNT(val)		bfin_write16(DMA10_X_COUNT, val)
+#define bfin_read_DMA10_Y_COUNT()		bfin_read16(DMA10_Y_COUNT)
+#define bfin_write_DMA10_Y_COUNT(val)		bfin_write16(DMA10_Y_COUNT, val)
+#define bfin_read_DMA10_X_MODIFY()		bfin_read16(DMA10_X_MODIFY)
+#define bfin_write_DMA10_X_MODIFY(val)		bfin_write16(DMA10_X_MODIFY, val)
+#define bfin_read_DMA10_Y_MODIFY()		bfin_read16(DMA10_Y_MODIFY)
+#define bfin_write_DMA10_Y_MODIFY(val)		bfin_write16(DMA10_Y_MODIFY, val)
+#define bfin_read_DMA10_CURR_DESC_PTR()		bfin_read32(DMA10_CURR_DESC_PTR)
+#define bfin_write_DMA10_CURR_DESC_PTR(val)	bfin_write32(DMA10_CURR_DESC_PTR, val)
+#define bfin_read_DMA10_CURR_ADDR()		bfin_read32(DMA10_CURR_ADDR)
+#define bfin_write_DMA10_CURR_ADDR(val)		bfin_write32(DMA10_CURR_ADDR, val)
+#define bfin_read_DMA10_CURR_X_COUNT()		bfin_read16(DMA10_CURR_X_COUNT)
+#define bfin_write_DMA10_CURR_X_COUNT(val)	bfin_write16(DMA10_CURR_X_COUNT, val)
+#define bfin_read_DMA10_CURR_Y_COUNT()		bfin_read16(DMA10_CURR_Y_COUNT)
+#define bfin_write_DMA10_CURR_Y_COUNT(val)	bfin_write16(DMA10_CURR_Y_COUNT, val)
+#define bfin_read_DMA10_IRQ_STATUS()		bfin_read16(DMA10_IRQ_STATUS)
+#define bfin_write_DMA10_IRQ_STATUS(val)	bfin_write16(DMA10_IRQ_STATUS, val)
+#define bfin_read_DMA10_PERIPHERAL_MAP()	bfin_read16(DMA10_PERIPHERAL_MAP)
+#define bfin_write_DMA10_PERIPHERAL_MAP(val)	bfin_write16(DMA10_PERIPHERAL_MAP, val)
+
+#define bfin_read_DMA11_CONFIG()		bfin_read16(DMA11_CONFIG)
+#define bfin_write_DMA11_CONFIG(val)		bfin_write16(DMA11_CONFIG, val)
+#define bfin_read_DMA11_NEXT_DESC_PTR()		bfin_read32(DMA11_NEXT_DESC_PTR)
+#define bfin_write_DMA11_NEXT_DESC_PTR(val)	bfin_write32(DMA11_NEXT_DESC_PTR, val)
+#define bfin_read_DMA11_START_ADDR()		bfin_read32(DMA11_START_ADDR)
+#define bfin_write_DMA11_START_ADDR(val)	bfin_write32(DMA11_START_ADDR, val)
+#define bfin_read_DMA11_X_COUNT()		bfin_read16(DMA11_X_COUNT)
+#define bfin_write_DMA11_X_COUNT(val)		bfin_write16(DMA11_X_COUNT, val)
+#define bfin_read_DMA11_Y_COUNT()		bfin_read16(DMA11_Y_COUNT)
+#define bfin_write_DMA11_Y_COUNT(val)		bfin_write16(DMA11_Y_COUNT, val)
+#define bfin_read_DMA11_X_MODIFY()		bfin_read16(DMA11_X_MODIFY)
+#define bfin_write_DMA11_X_MODIFY(val)		bfin_write16(DMA11_X_MODIFY, val)
+#define bfin_read_DMA11_Y_MODIFY()		bfin_read16(DMA11_Y_MODIFY)
+#define bfin_write_DMA11_Y_MODIFY(val)		bfin_write16(DMA11_Y_MODIFY, val)
+#define bfin_read_DMA11_CURR_DESC_PTR()		bfin_read32(DMA11_CURR_DESC_PTR)
+#define bfin_write_DMA11_CURR_DESC_PTR(val)	bfin_write32(DMA11_CURR_DESC_PTR, val)
+#define bfin_read_DMA11_CURR_ADDR()		bfin_read32(DMA11_CURR_ADDR)
+#define bfin_write_DMA11_CURR_ADDR(val)		bfin_write32(DMA11_CURR_ADDR, val)
+#define bfin_read_DMA11_CURR_X_COUNT()		bfin_read16(DMA11_CURR_X_COUNT)
+#define bfin_write_DMA11_CURR_X_COUNT(val)	bfin_write16(DMA11_CURR_X_COUNT, val)
+#define bfin_read_DMA11_CURR_Y_COUNT()		bfin_read16(DMA11_CURR_Y_COUNT)
+#define bfin_write_DMA11_CURR_Y_COUNT(val)	bfin_write16(DMA11_CURR_Y_COUNT, val)
+#define bfin_read_DMA11_IRQ_STATUS()		bfin_read16(DMA11_IRQ_STATUS)
+#define bfin_write_DMA11_IRQ_STATUS(val)	bfin_write16(DMA11_IRQ_STATUS, val)
+#define bfin_read_DMA11_PERIPHERAL_MAP()	bfin_read16(DMA11_PERIPHERAL_MAP)
+#define bfin_write_DMA11_PERIPHERAL_MAP(val)	bfin_write16(DMA11_PERIPHERAL_MAP, val)
+
+#define bfin_read_MDMA_D0_CONFIG()		bfin_read16(MDMA_D0_CONFIG)
+#define bfin_write_MDMA_D0_CONFIG(val)		bfin_write16(MDMA_D0_CONFIG, val)
+#define bfin_read_MDMA_D0_NEXT_DESC_PTR()	bfin_read32(MDMA_D0_NEXT_DESC_PTR)
+#define bfin_write_MDMA_D0_NEXT_DESC_PTR(val)	bfin_write32(MDMA_D0_NEXT_DESC_PTR, val)
+#define bfin_read_MDMA_D0_START_ADDR()		bfin_read32(MDMA_D0_START_ADDR)
+#define bfin_write_MDMA_D0_START_ADDR(val)	bfin_write32(MDMA_D0_START_ADDR, val)
+#define bfin_read_MDMA_D0_X_COUNT()		bfin_read16(MDMA_D0_X_COUNT)
+#define bfin_write_MDMA_D0_X_COUNT(val)		bfin_write16(MDMA_D0_X_COUNT, val)
+#define bfin_read_MDMA_D0_Y_COUNT()		bfin_read16(MDMA_D0_Y_COUNT)
+#define bfin_write_MDMA_D0_Y_COUNT(val)		bfin_write16(MDMA_D0_Y_COUNT, val)
+#define bfin_read_MDMA_D0_X_MODIFY()		bfin_read16(MDMA_D0_X_MODIFY)
+#define bfin_write_MDMA_D0_X_MODIFY(val)	bfin_write16(MDMA_D0_X_MODIFY, val)
+#define bfin_read_MDMA_D0_Y_MODIFY()		bfin_read16(MDMA_D0_Y_MODIFY)
+#define bfin_write_MDMA_D0_Y_MODIFY(val)	bfin_write16(MDMA_D0_Y_MODIFY, val)
+#define bfin_read_MDMA_D0_CURR_DESC_PTR()	bfin_read32(MDMA_D0_CURR_DESC_PTR)
+#define bfin_write_MDMA_D0_CURR_DESC_PTR(val)	bfin_write32(MDMA_D0_CURR_DESC_PTR, val)
+#define bfin_read_MDMA_D0_CURR_ADDR()		bfin_read32(MDMA_D0_CURR_ADDR)
+#define bfin_write_MDMA_D0_CURR_ADDR(val)	bfin_write32(MDMA_D0_CURR_ADDR, val)
+#define bfin_read_MDMA_D0_CURR_X_COUNT()	bfin_read16(MDMA_D0_CURR_X_COUNT)
+#define bfin_write_MDMA_D0_CURR_X_COUNT(val)	bfin_write16(MDMA_D0_CURR_X_COUNT, val)
+#define bfin_read_MDMA_D0_CURR_Y_COUNT()	bfin_read16(MDMA_D0_CURR_Y_COUNT)
+#define bfin_write_MDMA_D0_CURR_Y_COUNT(val)	bfin_write16(MDMA_D0_CURR_Y_COUNT, val)
+#define bfin_read_MDMA_D0_IRQ_STATUS()		bfin_read16(MDMA_D0_IRQ_STATUS)
+#define bfin_write_MDMA_D0_IRQ_STATUS(val)	bfin_write16(MDMA_D0_IRQ_STATUS, val)
+#define bfin_read_MDMA_D0_PERIPHERAL_MAP()	bfin_read16(MDMA_D0_PERIPHERAL_MAP)
+#define bfin_write_MDMA_D0_PERIPHERAL_MAP(val)	bfin_write16(MDMA_D0_PERIPHERAL_MAP, val)
+
+#define bfin_read_MDMA_S0_CONFIG()		bfin_read16(MDMA_S0_CONFIG)
+#define bfin_write_MDMA_S0_CONFIG(val)		bfin_write16(MDMA_S0_CONFIG, val)
+#define bfin_read_MDMA_S0_NEXT_DESC_PTR()	bfin_read32(MDMA_S0_NEXT_DESC_PTR)
+#define bfin_write_MDMA_S0_NEXT_DESC_PTR(val)	bfin_write32(MDMA_S0_NEXT_DESC_PTR, val)
+#define bfin_read_MDMA_S0_START_ADDR()		bfin_read32(MDMA_S0_START_ADDR)
+#define bfin_write_MDMA_S0_START_ADDR(val)	bfin_write32(MDMA_S0_START_ADDR, val)
+#define bfin_read_MDMA_S0_X_COUNT()		bfin_read16(MDMA_S0_X_COUNT)
+#define bfin_write_MDMA_S0_X_COUNT(val)		bfin_write16(MDMA_S0_X_COUNT, val)
+#define bfin_read_MDMA_S0_Y_COUNT()		bfin_read16(MDMA_S0_Y_COUNT)
+#define bfin_write_MDMA_S0_Y_COUNT(val)		bfin_write16(MDMA_S0_Y_COUNT, val)
+#define bfin_read_MDMA_S0_X_MODIFY()		bfin_read16(MDMA_S0_X_MODIFY)
+#define bfin_write_MDMA_S0_X_MODIFY(val)	bfin_write16(MDMA_S0_X_MODIFY, val)
+#define bfin_read_MDMA_S0_Y_MODIFY()		bfin_read16(MDMA_S0_Y_MODIFY)
+#define bfin_write_MDMA_S0_Y_MODIFY(val)	bfin_write16(MDMA_S0_Y_MODIFY, val)
+#define bfin_read_MDMA_S0_CURR_DESC_PTR()	bfin_read32(MDMA_S0_CURR_DESC_PTR)
+#define bfin_write_MDMA_S0_CURR_DESC_PTR(val)	bfin_write32(MDMA_S0_CURR_DESC_PTR, val)
+#define bfin_read_MDMA_S0_CURR_ADDR()		bfin_read32(MDMA_S0_CURR_ADDR)
+#define bfin_write_MDMA_S0_CURR_ADDR(val)	bfin_write32(MDMA_S0_CURR_ADDR, val)
+#define bfin_read_MDMA_S0_CURR_X_COUNT()	bfin_read16(MDMA_S0_CURR_X_COUNT)
+#define bfin_write_MDMA_S0_CURR_X_COUNT(val)	bfin_write16(MDMA_S0_CURR_X_COUNT, val)
+#define bfin_read_MDMA_S0_CURR_Y_COUNT()	bfin_read16(MDMA_S0_CURR_Y_COUNT)
+#define bfin_write_MDMA_S0_CURR_Y_COUNT(val)	bfin_write16(MDMA_S0_CURR_Y_COUNT, val)
+#define bfin_read_MDMA_S0_IRQ_STATUS()		bfin_read16(MDMA_S0_IRQ_STATUS)
+#define bfin_write_MDMA_S0_IRQ_STATUS(val)	bfin_write16(MDMA_S0_IRQ_STATUS, val)
+#define bfin_read_MDMA_S0_PERIPHERAL_MAP()	bfin_read16(MDMA_S0_PERIPHERAL_MAP)
+#define bfin_write_MDMA_S0_PERIPHERAL_MAP(val)	bfin_write16(MDMA_S0_PERIPHERAL_MAP, val)
+
+#define bfin_read_MDMA_D1_CONFIG()		bfin_read16(MDMA_D1_CONFIG)
+#define bfin_write_MDMA_D1_CONFIG(val)		bfin_write16(MDMA_D1_CONFIG, val)
+#define bfin_read_MDMA_D1_NEXT_DESC_PTR()	bfin_read32(MDMA_D1_NEXT_DESC_PTR)
+#define bfin_write_MDMA_D1_NEXT_DESC_PTR(val)	bfin_write32(MDMA_D1_NEXT_DESC_PTR, val)
+#define bfin_read_MDMA_D1_START_ADDR()		bfin_read32(MDMA_D1_START_ADDR)
+#define bfin_write_MDMA_D1_START_ADDR(val)	bfin_write32(MDMA_D1_START_ADDR, val)
+#define bfin_read_MDMA_D1_X_COUNT()		bfin_read16(MDMA_D1_X_COUNT)
+#define bfin_write_MDMA_D1_X_COUNT(val)		bfin_write16(MDMA_D1_X_COUNT, val)
+#define bfin_read_MDMA_D1_Y_COUNT()		bfin_read16(MDMA_D1_Y_COUNT)
+#define bfin_write_MDMA_D1_Y_COUNT(val)		bfin_write16(MDMA_D1_Y_COUNT, val)
+#define bfin_read_MDMA_D1_X_MODIFY()		bfin_read16(MDMA_D1_X_MODIFY)
+#define bfin_write_MDMA_D1_X_MODIFY(val)	bfin_write16(MDMA_D1_X_MODIFY, val)
+#define bfin_read_MDMA_D1_Y_MODIFY()		bfin_read16(MDMA_D1_Y_MODIFY)
+#define bfin_write_MDMA_D1_Y_MODIFY(val)	bfin_write16(MDMA_D1_Y_MODIFY, val)
+#define bfin_read_MDMA_D1_CURR_DESC_PTR()	bfin_read32(MDMA_D1_CURR_DESC_PTR)
+#define bfin_write_MDMA_D1_CURR_DESC_PTR(val)	bfin_write32(MDMA_D1_CURR_DESC_PTR, val)
+#define bfin_read_MDMA_D1_CURR_ADDR()		bfin_read32(MDMA_D1_CURR_ADDR)
+#define bfin_write_MDMA_D1_CURR_ADDR(val)	bfin_write32(MDMA_D1_CURR_ADDR, val)
+#define bfin_read_MDMA_D1_CURR_X_COUNT()	bfin_read16(MDMA_D1_CURR_X_COUNT)
+#define bfin_write_MDMA_D1_CURR_X_COUNT(val)	bfin_write16(MDMA_D1_CURR_X_COUNT, val)
+#define bfin_read_MDMA_D1_CURR_Y_COUNT()	bfin_read16(MDMA_D1_CURR_Y_COUNT)
+#define bfin_write_MDMA_D1_CURR_Y_COUNT(val)	bfin_write16(MDMA_D1_CURR_Y_COUNT, val)
+#define bfin_read_MDMA_D1_IRQ_STATUS()		bfin_read16(MDMA_D1_IRQ_STATUS)
+#define bfin_write_MDMA_D1_IRQ_STATUS(val)	bfin_write16(MDMA_D1_IRQ_STATUS, val)
+#define bfin_read_MDMA_D1_PERIPHERAL_MAP()	bfin_read16(MDMA_D1_PERIPHERAL_MAP)
+#define bfin_write_MDMA_D1_PERIPHERAL_MAP(val)	bfin_write16(MDMA_D1_PERIPHERAL_MAP, val)
+
+#define bfin_read_MDMA_S1_CONFIG()		bfin_read16(MDMA_S1_CONFIG)
+#define bfin_write_MDMA_S1_CONFIG(val)		bfin_write16(MDMA_S1_CONFIG, val)
+#define bfin_read_MDMA_S1_NEXT_DESC_PTR()	bfin_read32(MDMA_S1_NEXT_DESC_PTR)
+#define bfin_write_MDMA_S1_NEXT_DESC_PTR(val)	bfin_write32(MDMA_S1_NEXT_DESC_PTR, val)
+#define bfin_read_MDMA_S1_START_ADDR()		bfin_read32(MDMA_S1_START_ADDR)
+#define bfin_write_MDMA_S1_START_ADDR(val)	bfin_write32(MDMA_S1_START_ADDR, val)
+#define bfin_read_MDMA_S1_X_COUNT()		bfin_read16(MDMA_S1_X_COUNT)
+#define bfin_write_MDMA_S1_X_COUNT(val)		bfin_write16(MDMA_S1_X_COUNT, val)
+#define bfin_read_MDMA_S1_Y_COUNT()		bfin_read16(MDMA_S1_Y_COUNT)
+#define bfin_write_MDMA_S1_Y_COUNT(val)		bfin_write16(MDMA_S1_Y_COUNT, val)
+#define bfin_read_MDMA_S1_X_MODIFY()		bfin_read16(MDMA_S1_X_MODIFY)
+#define bfin_write_MDMA_S1_X_MODIFY(val)	bfin_write16(MDMA_S1_X_MODIFY, val)
+#define bfin_read_MDMA_S1_Y_MODIFY()		bfin_read16(MDMA_S1_Y_MODIFY)
+#define bfin_write_MDMA_S1_Y_MODIFY(val)	bfin_write16(MDMA_S1_Y_MODIFY, val)
+#define bfin_read_MDMA_S1_CURR_DESC_PTR()	bfin_read32(MDMA_S1_CURR_DESC_PTR)
+#define bfin_write_MDMA_S1_CURR_DESC_PTR(val)	bfin_write32(MDMA_S1_CURR_DESC_PTR, val)
+#define bfin_read_MDMA_S1_CURR_ADDR()		bfin_read32(MDMA_S1_CURR_ADDR)
+#define bfin_write_MDMA_S1_CURR_ADDR(val)	bfin_write32(MDMA_S1_CURR_ADDR, val)
+#define bfin_read_MDMA_S1_CURR_X_COUNT()	bfin_read16(MDMA_S1_CURR_X_COUNT)
+#define bfin_write_MDMA_S1_CURR_X_COUNT(val)	bfin_write16(MDMA_S1_CURR_X_COUNT, val)
+#define bfin_read_MDMA_S1_CURR_Y_COUNT()	bfin_read16(MDMA_S1_CURR_Y_COUNT)
+#define bfin_write_MDMA_S1_CURR_Y_COUNT(val)	bfin_write16(MDMA_S1_CURR_Y_COUNT, val)
+#define bfin_read_MDMA_S1_IRQ_STATUS()		bfin_read16(MDMA_S1_IRQ_STATUS)
+#define bfin_write_MDMA_S1_IRQ_STATUS(val)	bfin_write16(MDMA_S1_IRQ_STATUS, val)
+#define bfin_read_MDMA_S1_PERIPHERAL_MAP()	bfin_read16(MDMA_S1_PERIPHERAL_MAP)
+#define bfin_write_MDMA_S1_PERIPHERAL_MAP(val)	bfin_write16(MDMA_S1_PERIPHERAL_MAP, val)
+
+
+/* Parallel Peripheral Interface (0xFFC01000 - 0xFFC010FF)							*/
+#define bfin_read_PPI_CONTROL()			bfin_read16(PPI_CONTROL)
+#define bfin_write_PPI_CONTROL(val)		bfin_write16(PPI_CONTROL, val)
+#define bfin_read_PPI_STATUS()			bfin_read16(PPI_STATUS)
+#define bfin_write_PPI_STATUS(val)		bfin_write16(PPI_STATUS, val)
+#define bfin_read_PPI_DELAY()			bfin_read16(PPI_DELAY)
+#define bfin_write_PPI_DELAY(val)		bfin_write16(PPI_DELAY, val)
+#define bfin_read_PPI_COUNT()			bfin_read16(PPI_COUNT)
+#define bfin_write_PPI_COUNT(val)		bfin_write16(PPI_COUNT, val)
+#define bfin_read_PPI_FRAME()			bfin_read16(PPI_FRAME)
+#define bfin_write_PPI_FRAME(val)		bfin_write16(PPI_FRAME, val)
+
+
+/* Two-Wire Interface		(0xFFC01400 - 0xFFC014FF)								*/
+
+/* General Purpose I/O Port G (0xFFC01500 - 0xFFC015FF)								*/
+#define bfin_read_PORTGIO()			bfin_read16(PORTGIO)
+#define bfin_write_PORTGIO(val)			bfin_write16(PORTGIO, val)
+#define bfin_read_PORTGIO_CLEAR()		bfin_read16(PORTGIO_CLEAR)
+#define bfin_write_PORTGIO_CLEAR(val)		bfin_write16(PORTGIO_CLEAR, val)
+#define bfin_read_PORTGIO_SET()			bfin_read16(PORTGIO_SET)
+#define bfin_write_PORTGIO_SET(val)		bfin_write16(PORTGIO_SET, val)
+#define bfin_read_PORTGIO_TOGGLE()		bfin_read16(PORTGIO_TOGGLE)
+#define bfin_write_PORTGIO_TOGGLE(val)		bfin_write16(PORTGIO_TOGGLE, val)
+#define bfin_read_PORTGIO_MASKA()		bfin_read16(PORTGIO_MASKA)
+#define bfin_write_PORTGIO_MASKA(val)		bfin_write16(PORTGIO_MASKA, val)
+#define bfin_read_PORTGIO_MASKA_CLEAR()		bfin_read16(PORTGIO_MASKA_CLEAR)
+#define bfin_write_PORTGIO_MASKA_CLEAR(val)	bfin_write16(PORTGIO_MASKA_CLEAR, val)
+#define bfin_read_PORTGIO_MASKA_SET()		bfin_read16(PORTGIO_MASKA_SET)
+#define bfin_write_PORTGIO_MASKA_SET(val)	bfin_write16(PORTGIO_MASKA_SET, val)
+#define bfin_read_PORTGIO_MASKA_TOGGLE()	bfin_read16(PORTGIO_MASKA_TOGGLE)
+#define bfin_write_PORTGIO_MASKA_TOGGLE(val)	bfin_write16(PORTGIO_MASKA_TOGGLE, val)
+#define bfin_read_PORTGIO_MASKB()		bfin_read16(PORTGIO_MASKB)
+#define bfin_write_PORTGIO_MASKB(val)		bfin_write16(PORTGIO_MASKB, val)
+#define bfin_read_PORTGIO_MASKB_CLEAR()		bfin_read16(PORTGIO_MASKB_CLEAR)
+#define bfin_write_PORTGIO_MASKB_CLEAR(val)	bfin_write16(PORTGIO_MASKB_CLEAR, val)
+#define bfin_read_PORTGIO_MASKB_SET()		bfin_read16(PORTGIO_MASKB_SET)
+#define bfin_write_PORTGIO_MASKB_SET(val)	bfin_write16(PORTGIO_MASKB_SET, val)
+#define bfin_read_PORTGIO_MASKB_TOGGLE()	bfin_read16(PORTGIO_MASKB_TOGGLE)
+#define bfin_write_PORTGIO_MASKB_TOGGLE(val)	bfin_write16(PORTGIO_MASKB_TOGGLE, val)
+#define bfin_read_PORTGIO_DIR()			bfin_read16(PORTGIO_DIR)
+#define bfin_write_PORTGIO_DIR(val)		bfin_write16(PORTGIO_DIR, val)
+#define bfin_read_PORTGIO_POLAR()		bfin_read16(PORTGIO_POLAR)
+#define bfin_write_PORTGIO_POLAR(val)		bfin_write16(PORTGIO_POLAR, val)
+#define bfin_read_PORTGIO_EDGE()		bfin_read16(PORTGIO_EDGE)
+#define bfin_write_PORTGIO_EDGE(val)		bfin_write16(PORTGIO_EDGE, val)
+#define bfin_read_PORTGIO_BOTH()		bfin_read16(PORTGIO_BOTH)
+#define bfin_write_PORTGIO_BOTH(val)		bfin_write16(PORTGIO_BOTH, val)
+#define bfin_read_PORTGIO_INEN()		bfin_read16(PORTGIO_INEN)
+#define bfin_write_PORTGIO_INEN(val)		bfin_write16(PORTGIO_INEN, val)
+
+
+/* General Purpose I/O Port H (0xFFC01700 - 0xFFC017FF)								*/
+#define bfin_read_PORTHIO()			bfin_read16(PORTHIO)
+#define bfin_write_PORTHIO(val)			bfin_write16(PORTHIO, val)
+#define bfin_read_PORTHIO_CLEAR()		bfin_read16(PORTHIO_CLEAR)
+#define bfin_write_PORTHIO_CLEAR(val)		bfin_write16(PORTHIO_CLEAR, val)
+#define bfin_read_PORTHIO_SET()			bfin_read16(PORTHIO_SET)
+#define bfin_write_PORTHIO_SET(val)		bfin_write16(PORTHIO_SET, val)
+#define bfin_read_PORTHIO_TOGGLE()		bfin_read16(PORTHIO_TOGGLE)
+#define bfin_write_PORTHIO_TOGGLE(val)		bfin_write16(PORTHIO_TOGGLE, val)
+#define bfin_read_PORTHIO_MASKA()		bfin_read16(PORTHIO_MASKA)
+#define bfin_write_PORTHIO_MASKA(val)		bfin_write16(PORTHIO_MASKA, val)
+#define bfin_read_PORTHIO_MASKA_CLEAR()		bfin_read16(PORTHIO_MASKA_CLEAR)
+#define bfin_write_PORTHIO_MASKA_CLEAR(val)	bfin_write16(PORTHIO_MASKA_CLEAR, val)
+#define bfin_read_PORTHIO_MASKA_SET()		bfin_read16(PORTHIO_MASKA_SET)
+#define bfin_write_PORTHIO_MASKA_SET(val)	bfin_write16(PORTHIO_MASKA_SET, val)
+#define bfin_read_PORTHIO_MASKA_TOGGLE()	bfin_read16(PORTHIO_MASKA_TOGGLE)
+#define bfin_write_PORTHIO_MASKA_TOGGLE(val)	bfin_write16(PORTHIO_MASKA_TOGGLE, val)
+#define bfin_read_PORTHIO_MASKB()		bfin_read16(PORTHIO_MASKB)
+#define bfin_write_PORTHIO_MASKB(val)		bfin_write16(PORTHIO_MASKB, val)
+#define bfin_read_PORTHIO_MASKB_CLEAR()		bfin_read16(PORTHIO_MASKB_CLEAR)
+#define bfin_write_PORTHIO_MASKB_CLEAR(val)	bfin_write16(PORTHIO_MASKB_CLEAR, val)
+#define bfin_read_PORTHIO_MASKB_SET()		bfin_read16(PORTHIO_MASKB_SET)
+#define bfin_write_PORTHIO_MASKB_SET(val)	bfin_write16(PORTHIO_MASKB_SET, val)
+#define bfin_read_PORTHIO_MASKB_TOGGLE()	bfin_read16(PORTHIO_MASKB_TOGGLE)
+#define bfin_write_PORTHIO_MASKB_TOGGLE(val)	bfin_write16(PORTHIO_MASKB_TOGGLE, val)
+#define bfin_read_PORTHIO_DIR()			bfin_read16(PORTHIO_DIR)
+#define bfin_write_PORTHIO_DIR(val)		bfin_write16(PORTHIO_DIR, val)
+#define bfin_read_PORTHIO_POLAR()		bfin_read16(PORTHIO_POLAR)
+#define bfin_write_PORTHIO_POLAR(val)		bfin_write16(PORTHIO_POLAR, val)
+#define bfin_read_PORTHIO_EDGE()		bfin_read16(PORTHIO_EDGE)
+#define bfin_write_PORTHIO_EDGE(val)		bfin_write16(PORTHIO_EDGE, val)
+#define bfin_read_PORTHIO_BOTH()		bfin_read16(PORTHIO_BOTH)
+#define bfin_write_PORTHIO_BOTH(val)		bfin_write16(PORTHIO_BOTH, val)
+#define bfin_read_PORTHIO_INEN()		bfin_read16(PORTHIO_INEN)
+#define bfin_write_PORTHIO_INEN(val)		bfin_write16(PORTHIO_INEN, val)
+
+
+/* UART1 Controller		(0xFFC02000 - 0xFFC020FF)								*/
+#define bfin_read_UART1_THR()			bfin_read16(UART1_THR)
+#define bfin_write_UART1_THR(val)		bfin_write16(UART1_THR, val)
+#define bfin_read_UART1_RBR()			bfin_read16(UART1_RBR)
+#define bfin_write_UART1_RBR(val)		bfin_write16(UART1_RBR, val)
+#define bfin_read_UART1_DLL()			bfin_read16(UART1_DLL)
+#define bfin_write_UART1_DLL(val)		bfin_write16(UART1_DLL, val)
+#define bfin_read_UART1_IER()			bfin_read16(UART1_IER)
+#define bfin_write_UART1_IER(val)		bfin_write16(UART1_IER, val)
+#define bfin_read_UART1_DLH()			bfin_read16(UART1_DLH)
+#define bfin_write_UART1_DLH(val)		bfin_write16(UART1_DLH, val)
+#define bfin_read_UART1_IIR()			bfin_read16(UART1_IIR)
+#define bfin_write_UART1_IIR(val)		bfin_write16(UART1_IIR, val)
+#define bfin_read_UART1_LCR()			bfin_read16(UART1_LCR)
+#define bfin_write_UART1_LCR(val)		bfin_write16(UART1_LCR, val)
+#define bfin_read_UART1_MCR()			bfin_read16(UART1_MCR)
+#define bfin_write_UART1_MCR(val)		bfin_write16(UART1_MCR, val)
+#define bfin_read_UART1_LSR()			bfin_read16(UART1_LSR)
+#define bfin_write_UART1_LSR(val)		bfin_write16(UART1_LSR, val)
+#define bfin_read_UART1_MSR()			bfin_read16(UART1_MSR)
+#define bfin_write_UART1_MSR(val)		bfin_write16(UART1_MSR, val)
+#define bfin_read_UART1_SCR()			bfin_read16(UART1_SCR)
+#define bfin_write_UART1_SCR(val)		bfin_write16(UART1_SCR, val)
+#define bfin_read_UART1_GCTL()			bfin_read16(UART1_GCTL)
+#define bfin_write_UART1_GCTL(val)		bfin_write16(UART1_GCTL, val)
+
+/* Omit CAN register sets from the cdefBF534.h (CAN is not in the ADSP-BF52x processor) */
+
+/* Pin Control Registers	(0xFFC03200 - 0xFFC032FF)								*/
+#define bfin_read_PORTF_FER()			bfin_read16(PORTF_FER)
+#define bfin_write_PORTF_FER(val)		bfin_write16(PORTF_FER, val)
+#define bfin_read_PORTG_FER()			bfin_read16(PORTG_FER)
+#define bfin_write_PORTG_FER(val)		bfin_write16(PORTG_FER, val)
+#define bfin_read_PORTH_FER()			bfin_read16(PORTH_FER)
+#define bfin_write_PORTH_FER(val)		bfin_write16(PORTH_FER, val)
+#define bfin_read_PORT_MUX()			bfin_read16(PORT_MUX)
+#define bfin_write_PORT_MUX(val)		bfin_write16(PORT_MUX, val)
+
+
+/* Handshake MDMA Registers	(0xFFC03300 - 0xFFC033FF)								*/
+#define bfin_read_HMDMA0_CONTROL()		bfin_read16(HMDMA0_CONTROL)
+#define bfin_write_HMDMA0_CONTROL(val)		bfin_write16(HMDMA0_CONTROL, val)
+#define bfin_read_HMDMA0_ECINIT()		bfin_read16(HMDMA0_ECINIT)
+#define bfin_write_HMDMA0_ECINIT(val)		bfin_write16(HMDMA0_ECINIT, val)
+#define bfin_read_HMDMA0_BCINIT()		bfin_read16(HMDMA0_BCINIT)
+#define bfin_write_HMDMA0_BCINIT(val)		bfin_write16(HMDMA0_BCINIT, val)
+#define bfin_read_HMDMA0_ECURGENT()		bfin_read16(HMDMA0_ECURGENT)
+#define bfin_write_HMDMA0_ECURGENT(val)		bfin_write16(HMDMA0_ECURGENT, val)
+#define bfin_read_HMDMA0_ECOVERFLOW()		bfin_read16(HMDMA0_ECOVERFLOW)
+#define bfin_write_HMDMA0_ECOVERFLOW(val)	bfin_write16(HMDMA0_ECOVERFLOW, val)
+#define bfin_read_HMDMA0_ECOUNT()		bfin_read16(HMDMA0_ECOUNT)
+#define bfin_write_HMDMA0_ECOUNT(val)		bfin_write16(HMDMA0_ECOUNT, val)
+#define bfin_read_HMDMA0_BCOUNT()		bfin_read16(HMDMA0_BCOUNT)
+#define bfin_write_HMDMA0_BCOUNT(val)		bfin_write16(HMDMA0_BCOUNT, val)
+
+#define bfin_read_HMDMA1_CONTROL()		bfin_read16(HMDMA1_CONTROL)
+#define bfin_write_HMDMA1_CONTROL(val)		bfin_write16(HMDMA1_CONTROL, val)
+#define bfin_read_HMDMA1_ECINIT()		bfin_read16(HMDMA1_ECINIT)
+#define bfin_write_HMDMA1_ECINIT(val)		bfin_write16(HMDMA1_ECINIT, val)
+#define bfin_read_HMDMA1_BCINIT()		bfin_read16(HMDMA1_BCINIT)
+#define bfin_write_HMDMA1_BCINIT(val)		bfin_write16(HMDMA1_BCINIT, val)
+#define bfin_read_HMDMA1_ECURGENT()		bfin_read16(HMDMA1_ECURGENT)
+#define bfin_write_HMDMA1_ECURGENT(val)		bfin_write16(HMDMA1_ECURGENT, val)
+#define bfin_read_HMDMA1_ECOVERFLOW()		bfin_read16(HMDMA1_ECOVERFLOW)
+#define bfin_write_HMDMA1_ECOVERFLOW(val)	bfin_write16(HMDMA1_ECOVERFLOW, val)
+#define bfin_read_HMDMA1_ECOUNT()		bfin_read16(HMDMA1_ECOUNT)
+#define bfin_write_HMDMA1_ECOUNT(val)		bfin_write16(HMDMA1_ECOUNT, val)
+#define bfin_read_HMDMA1_BCOUNT()		bfin_read16(HMDMA1_BCOUNT)
+#define bfin_write_HMDMA1_BCOUNT(val)		bfin_write16(HMDMA1_BCOUNT, val)
+
+/* ==== end from cdefBF534.h ==== */
+
+/* GPIO PIN mux (0xFFC03210 - OxFFC03288) */
+
+#define bfin_read_PORTF_MUX()			bfin_read16(PORTF_MUX)
+#define bfin_write_PORTF_MUX(val)		bfin_write16(PORTF_MUX, val)
+#define bfin_read_PORTG_MUX()			bfin_read16(PORTG_MUX)
+#define bfin_write_PORTG_MUX(val)		bfin_write16(PORTG_MUX, val)
+#define bfin_read_PORTH_MUX()			bfin_read16(PORTH_MUX)
+#define bfin_write_PORTH_MUX(val)		bfin_write16(PORTH_MUX, val)
+
+#define bfin_read_PORTF_DRIVE()			bfin_read16(PORTF_DRIVE)
+#define bfin_write_PORTF_DRIVE(val)		bfin_write16(PORTF_DRIVE, val)
+#define bfin_read_PORTG_DRIVE()			bfin_read16(PORTG_DRIVE)
+#define bfin_write_PORTG_DRIVE(val)		bfin_write16(PORTG_DRIVE, val)
+#define bfin_read_PORTH_DRIVE()			bfin_read16(PORTH_DRIVE)
+#define bfin_write_PORTH_DRIVE(val)		bfin_write16(PORTH_DRIVE, val)
+#define bfin_read_PORTF_SLEW()			bfin_read16(PORTF_SLEW)
+#define bfin_write_PORTF_SLEW(val)		bfin_write16(PORTF_SLEW, val)
+#define bfin_read_PORTG_SLEW()			bfin_read16(PORTG_SLEW)
+#define bfin_write_PORTG_SLEW(val)		bfin_write16(PORTG_SLEW, val)
+#define bfin_read_PORTH_SLEW()			bfin_read16(PORTH_SLEW)
+#define bfin_write_PORTH_SLEW(val)		bfin_write16(PORTH_SLEW, val)
+#define bfin_read_PORTF_HYSTERISIS()		bfin_read16(PORTF_HYSTERISIS)
+#define bfin_write_PORTF_HYSTERISIS(val)	bfin_write16(PORTF_HYSTERISIS, val)
+#define bfin_read_PORTG_HYSTERISIS()		bfin_read16(PORTG_HYSTERISIS)
+#define bfin_write_PORTG_HYSTERISIS(val)	bfin_write16(PORTG_HYSTERISIS, val)
+#define bfin_read_PORTH_HYSTERISIS()		bfin_read16(PORTH_HYSTERISIS)
+#define bfin_write_PORTH_HYSTERISIS(val)	bfin_write16(PORTH_HYSTERISIS, val)
+#define bfin_read_MISCPORT_DRIVE()		bfin_read16(MISCPORT_DRIVE)
+#define bfin_write_MISCPORT_DRIVE(val)		bfin_write16(MISCPORT_DRIVE, val)
+#define bfin_read_MISCPORT_SLEW()		bfin_read16(MISCPORT_SLEW)
+#define bfin_write_MISCPORT_SLEW(val)		bfin_write16(MISCPORT_SLEW, val)
+#define bfin_read_MISCPORT_HYSTERISIS()		bfin_read16(MISCPORT_HYSTERISIS)
+#define bfin_write_MISCPORT_HYSTERISIS(val)	bfin_write16(MISCPORT_HYSTERISIS, val)
+
+/* HOST Port Registers */
+
+#define bfin_read_HOST_CONTROL()		bfin_read16(HOST_CONTROL)
+#define bfin_write_HOST_CONTROL(val)		bfin_write16(HOST_CONTROL, val)
+#define bfin_read_HOST_STATUS()			bfin_read16(HOST_STATUS)
+#define bfin_write_HOST_STATUS(val)		bfin_write16(HOST_STATUS, val)
+#define bfin_read_HOST_TIMEOUT()		bfin_read16(HOST_TIMEOUT)
+#define bfin_write_HOST_TIMEOUT(val)		bfin_write16(HOST_TIMEOUT, val)
+
+/* Counter Registers */
+
+#define bfin_read_CNT_CONFIG()			bfin_read16(CNT_CONFIG)
+#define bfin_write_CNT_CONFIG(val)		bfin_write16(CNT_CONFIG, val)
+#define bfin_read_CNT_IMASK()			bfin_read16(CNT_IMASK)
+#define bfin_write_CNT_IMASK(val)		bfin_write16(CNT_IMASK, val)
+#define bfin_read_CNT_STATUS()			bfin_read16(CNT_STATUS)
+#define bfin_write_CNT_STATUS(val)		bfin_write16(CNT_STATUS, val)
+#define bfin_read_CNT_COMMAND()			bfin_read16(CNT_COMMAND)
+#define bfin_write_CNT_COMMAND(val)		bfin_write16(CNT_COMMAND, val)
+#define bfin_read_CNT_DEBOUNCE()		bfin_read16(CNT_DEBOUNCE)
+#define bfin_write_CNT_DEBOUNCE(val)		bfin_write16(CNT_DEBOUNCE, val)
+#define bfin_read_CNT_COUNTER()			bfin_read32(CNT_COUNTER)
+#define bfin_write_CNT_COUNTER(val)		bfin_write32(CNT_COUNTER, val)
+#define bfin_read_CNT_MAX()			bfin_read32(CNT_MAX)
+#define bfin_write_CNT_MAX(val)			bfin_write32(CNT_MAX, val)
+#define bfin_read_CNT_MIN()			bfin_read32(CNT_MIN)
+#define bfin_write_CNT_MIN(val)			bfin_write32(CNT_MIN, val)
+
+/* OTP/FUSE Registers */
+
+#define bfin_read_OTP_CONTROL()			bfin_read16(OTP_CONTROL)
+#define bfin_write_OTP_CONTROL(val)		bfin_write16(OTP_CONTROL, val)
+#define bfin_read_OTP_BEN()			bfin_read16(OTP_BEN)
+#define bfin_write_OTP_BEN(val)			bfin_write16(OTP_BEN, val)
+#define bfin_read_OTP_STATUS()			bfin_read16(OTP_STATUS)
+#define bfin_write_OTP_STATUS(val)		bfin_write16(OTP_STATUS, val)
+#define bfin_read_OTP_TIMING()			bfin_read32(OTP_TIMING)
+#define bfin_write_OTP_TIMING(val)		bfin_write32(OTP_TIMING, val)
+
+/* Security Registers */
+
+#define bfin_read_SECURE_SYSSWT()		bfin_read32(SECURE_SYSSWT)
+#define bfin_write_SECURE_SYSSWT(val)		bfin_write32(SECURE_SYSSWT, val)
+#define bfin_read_SECURE_CONTROL()		bfin_read16(SECURE_CONTROL)
+#define bfin_write_SECURE_CONTROL(val)		bfin_write16(SECURE_CONTROL, val)
+#define bfin_read_SECURE_STATUS()		bfin_read16(SECURE_STATUS)
+#define bfin_write_SECURE_STATUS(val)		bfin_write16(SECURE_STATUS, val)
+
+/* OTP Read/Write Data Buffer Registers */
+
+#define bfin_read_OTP_DATA0()			bfin_read32(OTP_DATA0)
+#define bfin_write_OTP_DATA0(val)		bfin_write32(OTP_DATA0, val)
+#define bfin_read_OTP_DATA1()			bfin_read32(OTP_DATA1)
+#define bfin_write_OTP_DATA1(val)		bfin_write32(OTP_DATA1, val)
+#define bfin_read_OTP_DATA2()			bfin_read32(OTP_DATA2)
+#define bfin_write_OTP_DATA2(val)		bfin_write32(OTP_DATA2, val)
+#define bfin_read_OTP_DATA3()			bfin_read32(OTP_DATA3)
+#define bfin_write_OTP_DATA3(val)		bfin_write32(OTP_DATA3, val)
+
+/* NFC Registers */
+
+#define bfin_read_NFC_CTL()			bfin_read16(NFC_CTL)
+#define bfin_write_NFC_CTL(val)			bfin_write16(NFC_CTL, val)
+#define bfin_read_NFC_STAT()			bfin_read16(NFC_STAT)
+#define bfin_write_NFC_STAT(val)		bfin_write16(NFC_STAT, val)
+#define bfin_read_NFC_IRQSTAT()			bfin_read16(NFC_IRQSTAT)
+#define bfin_write_NFC_IRQSTAT(val)		bfin_write16(NFC_IRQSTAT, val)
+#define bfin_read_NFC_IRQMASK()			bfin_read16(NFC_IRQMASK)
+#define bfin_write_NFC_IRQMASK(val)		bfin_write16(NFC_IRQMASK, val)
+#define bfin_read_NFC_ECC0()			bfin_read16(NFC_ECC0)
+#define bfin_write_NFC_ECC0(val)		bfin_write16(NFC_ECC0, val)
+#define bfin_read_NFC_ECC1()			bfin_read16(NFC_ECC1)
+#define bfin_write_NFC_ECC1(val)		bfin_write16(NFC_ECC1, val)
+#define bfin_read_NFC_ECC2()			bfin_read16(NFC_ECC2)
+#define bfin_write_NFC_ECC2(val)		bfin_write16(NFC_ECC2, val)
+#define bfin_read_NFC_ECC3()			bfin_read16(NFC_ECC3)
+#define bfin_write_NFC_ECC3(val)		bfin_write16(NFC_ECC3, val)
+#define bfin_read_NFC_COUNT()			bfin_read16(NFC_COUNT)
+#define bfin_write_NFC_COUNT(val)		bfin_write16(NFC_COUNT, val)
+#define bfin_read_NFC_RST()			bfin_read16(NFC_RST)
+#define bfin_write_NFC_RST(val)			bfin_write16(NFC_RST, val)
+#define bfin_read_NFC_PGCTL()			bfin_read16(NFC_PGCTL)
+#define bfin_write_NFC_PGCTL(val)		bfin_write16(NFC_PGCTL, val)
+#define bfin_read_NFC_READ()			bfin_read16(NFC_READ)
+#define bfin_write_NFC_READ(val)		bfin_write16(NFC_READ, val)
+#define bfin_read_NFC_ADDR()			bfin_read16(NFC_ADDR)
+#define bfin_write_NFC_ADDR(val)		bfin_write16(NFC_ADDR, val)
+#define bfin_read_NFC_CMD()			bfin_read16(NFC_CMD)
+#define bfin_write_NFC_CMD(val)			bfin_write16(NFC_CMD, val)
+#define bfin_read_NFC_DATA_WR()			bfin_read16(NFC_DATA_WR)
+#define bfin_write_NFC_DATA_WR(val)		bfin_write16(NFC_DATA_WR, val)
+#define bfin_read_NFC_DATA_RD()			bfin_read16(NFC_DATA_RD)
+#define bfin_write_NFC_DATA_RD(val)		bfin_write16(NFC_DATA_RD, val)
+
+#endif /* _CDEF_BF52X_H */
diff --git a/arch/blackfin/mach-bf527/include/mach/defBF522.h b/arch/blackfin/mach-bf527/include/mach/defBF522.h
new file mode 100644
index 00000000000..0a8cdcdf0b4
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/defBF522.h
@@ -0,0 +1,42 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/defBF522.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _DEF_BF522_H
+#define _DEF_BF522_H
+
+/* Include all Core registers and bit definitions */
+#include <asm/def_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF522 */
+
+/* Include defBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */
+#include "defBF52x_base.h"
+
+#endif /* _DEF_BF522_H */
diff --git a/arch/blackfin/mach-bf527/include/mach/defBF525.h b/arch/blackfin/mach-bf527/include/mach/defBF525.h
new file mode 100644
index 00000000000..5cd7576fef7
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/defBF525.h
@@ -0,0 +1,713 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/defBF525.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _DEF_BF525_H
+#define _DEF_BF525_H
+
+/* Include all Core registers and bit definitions */
+#include <asm/def_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF525 */
+
+/* Include defBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */
+#include "defBF52x_base.h"
+
+/* The following are the #defines needed by ADSP-BF525 that are not in the common header */
+
+/* USB Control Registers */
+
+#define                        USB_FADDR  0xffc03800   /* Function address register */
+#define                        USB_POWER  0xffc03804   /* Power management register */
+#define                       USB_INTRTX  0xffc03808   /* Interrupt register for endpoint 0 and Tx endpoint 1 to 7 */
+#define                       USB_INTRRX  0xffc0380c   /* Interrupt register for Rx endpoints 1 to 7 */
+#define                      USB_INTRTXE  0xffc03810   /* Interrupt enable register for IntrTx */
+#define                      USB_INTRRXE  0xffc03814   /* Interrupt enable register for IntrRx */
+#define                      USB_INTRUSB  0xffc03818   /* Interrupt register for common USB interrupts */
+#define                     USB_INTRUSBE  0xffc0381c   /* Interrupt enable register for IntrUSB */
+#define                        USB_FRAME  0xffc03820   /* USB frame number */
+#define                        USB_INDEX  0xffc03824   /* Index register for selecting the indexed endpoint registers */
+#define                     USB_TESTMODE  0xffc03828   /* Enabled USB 20 test modes */
+#define                     USB_GLOBINTR  0xffc0382c   /* Global Interrupt Mask register and Wakeup Exception Interrupt */
+#define                   USB_GLOBAL_CTL  0xffc03830   /* Global Clock Control for the core */
+
+/* USB Packet Control Registers */
+
+#define                USB_TX_MAX_PACKET  0xffc03840   /* Maximum packet size for Host Tx endpoint */
+#define                         USB_CSR0  0xffc03844   /* Control Status register for endpoint 0 and Control Status register for Host Tx endpoint */
+#define                        USB_TXCSR  0xffc03844   /* Control Status register for endpoint 0 and Control Status register for Host Tx endpoint */
+#define                USB_RX_MAX_PACKET  0xffc03848   /* Maximum packet size for Host Rx endpoint */
+#define                        USB_RXCSR  0xffc0384c   /* Control Status register for Host Rx endpoint */
+#define                       USB_COUNT0  0xffc03850   /* Number of bytes received in endpoint 0 FIFO and Number of bytes received in Host Tx endpoint */
+#define                      USB_RXCOUNT  0xffc03850   /* Number of bytes received in endpoint 0 FIFO and Number of bytes received in Host Tx endpoint */
+#define                       USB_TXTYPE  0xffc03854   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint */
+#define                    USB_NAKLIMIT0  0xffc03858   /* Sets the NAK response timeout on Endpoint 0 and on Bulk transfers for Host Tx endpoint */
+#define                   USB_TXINTERVAL  0xffc03858   /* Sets the NAK response timeout on Endpoint 0 and on Bulk transfers for Host Tx endpoint */
+#define                       USB_RXTYPE  0xffc0385c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint */
+#define                   USB_RXINTERVAL  0xffc03860   /* Sets the polling interval for Interrupt and Isochronous transfers or the NAK response timeout on Bulk transfers */
+#define                      USB_TXCOUNT  0xffc03868   /* Number of bytes to be written to the selected endpoint Tx FIFO */
+
+/* USB Endpoint FIFO Registers */
+
+#define                     USB_EP0_FIFO  0xffc03880   /* Endpoint 0 FIFO */
+#define                     USB_EP1_FIFO  0xffc03888   /* Endpoint 1 FIFO */
+#define                     USB_EP2_FIFO  0xffc03890   /* Endpoint 2 FIFO */
+#define                     USB_EP3_FIFO  0xffc03898   /* Endpoint 3 FIFO */
+#define                     USB_EP4_FIFO  0xffc038a0   /* Endpoint 4 FIFO */
+#define                     USB_EP5_FIFO  0xffc038a8   /* Endpoint 5 FIFO */
+#define                     USB_EP6_FIFO  0xffc038b0   /* Endpoint 6 FIFO */
+#define                     USB_EP7_FIFO  0xffc038b8   /* Endpoint 7 FIFO */
+
+/* USB OTG Control Registers */
+
+#define                  USB_OTG_DEV_CTL  0xffc03900   /* OTG Device Control Register */
+#define                 USB_OTG_VBUS_IRQ  0xffc03904   /* OTG VBUS Control Interrupts */
+#define                USB_OTG_VBUS_MASK  0xffc03908   /* VBUS Control Interrupt Enable */
+
+/* USB Phy Control Registers */
+
+#define                     USB_LINKINFO  0xffc03948   /* Enables programming of some PHY-side delays */
+#define                        USB_VPLEN  0xffc0394c   /* Determines duration of VBUS pulse for VBUS charging */
+#define                      USB_HS_EOF1  0xffc03950   /* Time buffer for High-Speed transactions */
+#define                      USB_FS_EOF1  0xffc03954   /* Time buffer for Full-Speed transactions */
+#define                      USB_LS_EOF1  0xffc03958   /* Time buffer for Low-Speed transactions */
+
+/* (APHY_CNTRL is for ADI usage only) */
+
+#define                   USB_APHY_CNTRL  0xffc039e0   /* Register that increases visibility of Analog PHY */
+
+/* (APHY_CALIB is for ADI usage only) */
+
+#define                   USB_APHY_CALIB  0xffc039e4   /* Register used to set some calibration values */
+
+#define                  USB_APHY_CNTRL2  0xffc039e8   /* Register used to prevent re-enumeration once Moab goes into hibernate mode */
+
+/* (PHY_TEST is for ADI usage only) */
+
+#define                     USB_PHY_TEST  0xffc039ec   /* Used for reducing simulation time and simplifies FIFO testability */
+
+#define                  USB_PLLOSC_CTRL  0xffc039f0   /* Used to program different parameters for USB PLL and Oscillator */
+#define                   USB_SRP_CLKDIV  0xffc039f4   /* Used to program clock divide value for the clock fed to the SRP detection logic */
+
+/* USB Endpoint 0 Control Registers */
+
+#define                USB_EP_NI0_TXMAXP  0xffc03a00   /* Maximum packet size for Host Tx endpoint0 */
+#define                 USB_EP_NI0_TXCSR  0xffc03a04   /* Control Status register for endpoint 0 */
+#define                USB_EP_NI0_RXMAXP  0xffc03a08   /* Maximum packet size for Host Rx endpoint0 */
+#define                 USB_EP_NI0_RXCSR  0xffc03a0c   /* Control Status register for Host Rx endpoint0 */
+#define               USB_EP_NI0_RXCOUNT  0xffc03a10   /* Number of bytes received in endpoint 0 FIFO */
+#define                USB_EP_NI0_TXTYPE  0xffc03a14   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint0 */
+#define            USB_EP_NI0_TXINTERVAL  0xffc03a18   /* Sets the NAK response timeout on Endpoint 0 */
+#define                USB_EP_NI0_RXTYPE  0xffc03a1c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint0 */
+#define            USB_EP_NI0_RXINTERVAL  0xffc03a20   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint0 */
+#define               USB_EP_NI0_TXCOUNT  0xffc03a28   /* Number of bytes to be written to the endpoint0 Tx FIFO */
+
+/* USB Endpoint 1 Control Registers */
+
+#define                USB_EP_NI1_TXMAXP  0xffc03a40   /* Maximum packet size for Host Tx endpoint1 */
+#define                 USB_EP_NI1_TXCSR  0xffc03a44   /* Control Status register for endpoint1 */
+#define                USB_EP_NI1_RXMAXP  0xffc03a48   /* Maximum packet size for Host Rx endpoint1 */
+#define                 USB_EP_NI1_RXCSR  0xffc03a4c   /* Control Status register for Host Rx endpoint1 */
+#define               USB_EP_NI1_RXCOUNT  0xffc03a50   /* Number of bytes received in endpoint1 FIFO */
+#define                USB_EP_NI1_TXTYPE  0xffc03a54   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint1 */
+#define            USB_EP_NI1_TXINTERVAL  0xffc03a58   /* Sets the NAK response timeout on Endpoint1 */
+#define                USB_EP_NI1_RXTYPE  0xffc03a5c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint1 */
+#define            USB_EP_NI1_RXINTERVAL  0xffc03a60   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint1 */
+#define               USB_EP_NI1_TXCOUNT  0xffc03a68   /* Number of bytes to be written to the+H102 endpoint1 Tx FIFO */
+
+/* USB Endpoint 2 Control Registers */
+
+#define                USB_EP_NI2_TXMAXP  0xffc03a80   /* Maximum packet size for Host Tx endpoint2 */
+#define                 USB_EP_NI2_TXCSR  0xffc03a84   /* Control Status register for endpoint2 */
+#define                USB_EP_NI2_RXMAXP  0xffc03a88   /* Maximum packet size for Host Rx endpoint2 */
+#define                 USB_EP_NI2_RXCSR  0xffc03a8c   /* Control Status register for Host Rx endpoint2 */
+#define               USB_EP_NI2_RXCOUNT  0xffc03a90   /* Number of bytes received in endpoint2 FIFO */
+#define                USB_EP_NI2_TXTYPE  0xffc03a94   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint2 */
+#define            USB_EP_NI2_TXINTERVAL  0xffc03a98   /* Sets the NAK response timeout on Endpoint2 */
+#define                USB_EP_NI2_RXTYPE  0xffc03a9c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint2 */
+#define            USB_EP_NI2_RXINTERVAL  0xffc03aa0   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint2 */
+#define               USB_EP_NI2_TXCOUNT  0xffc03aa8   /* Number of bytes to be written to the endpoint2 Tx FIFO */
+
+/* USB Endpoint 3 Control Registers */
+
+#define                USB_EP_NI3_TXMAXP  0xffc03ac0   /* Maximum packet size for Host Tx endpoint3 */
+#define                 USB_EP_NI3_TXCSR  0xffc03ac4   /* Control Status register for endpoint3 */
+#define                USB_EP_NI3_RXMAXP  0xffc03ac8   /* Maximum packet size for Host Rx endpoint3 */
+#define                 USB_EP_NI3_RXCSR  0xffc03acc   /* Control Status register for Host Rx endpoint3 */
+#define               USB_EP_NI3_RXCOUNT  0xffc03ad0   /* Number of bytes received in endpoint3 FIFO */
+#define                USB_EP_NI3_TXTYPE  0xffc03ad4   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint3 */
+#define            USB_EP_NI3_TXINTERVAL  0xffc03ad8   /* Sets the NAK response timeout on Endpoint3 */
+#define                USB_EP_NI3_RXTYPE  0xffc03adc   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint3 */
+#define            USB_EP_NI3_RXINTERVAL  0xffc03ae0   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint3 */
+#define               USB_EP_NI3_TXCOUNT  0xffc03ae8   /* Number of bytes to be written to the H124endpoint3 Tx FIFO */
+
+/* USB Endpoint 4 Control Registers */
+
+#define                USB_EP_NI4_TXMAXP  0xffc03b00   /* Maximum packet size for Host Tx endpoint4 */
+#define                 USB_EP_NI4_TXCSR  0xffc03b04   /* Control Status register for endpoint4 */
+#define                USB_EP_NI4_RXMAXP  0xffc03b08   /* Maximum packet size for Host Rx endpoint4 */
+#define                 USB_EP_NI4_RXCSR  0xffc03b0c   /* Control Status register for Host Rx endpoint4 */
+#define               USB_EP_NI4_RXCOUNT  0xffc03b10   /* Number of bytes received in endpoint4 FIFO */
+#define                USB_EP_NI4_TXTYPE  0xffc03b14   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint4 */
+#define            USB_EP_NI4_TXINTERVAL  0xffc03b18   /* Sets the NAK response timeout on Endpoint4 */
+#define                USB_EP_NI4_RXTYPE  0xffc03b1c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint4 */
+#define            USB_EP_NI4_RXINTERVAL  0xffc03b20   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint4 */
+#define               USB_EP_NI4_TXCOUNT  0xffc03b28   /* Number of bytes to be written to the endpoint4 Tx FIFO */
+
+/* USB Endpoint 5 Control Registers */
+
+#define                USB_EP_NI5_TXMAXP  0xffc03b40   /* Maximum packet size for Host Tx endpoint5 */
+#define                 USB_EP_NI5_TXCSR  0xffc03b44   /* Control Status register for endpoint5 */
+#define                USB_EP_NI5_RXMAXP  0xffc03b48   /* Maximum packet size for Host Rx endpoint5 */
+#define                 USB_EP_NI5_RXCSR  0xffc03b4c   /* Control Status register for Host Rx endpoint5 */
+#define               USB_EP_NI5_RXCOUNT  0xffc03b50   /* Number of bytes received in endpoint5 FIFO */
+#define                USB_EP_NI5_TXTYPE  0xffc03b54   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint5 */
+#define            USB_EP_NI5_TXINTERVAL  0xffc03b58   /* Sets the NAK response timeout on Endpoint5 */
+#define                USB_EP_NI5_RXTYPE  0xffc03b5c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint5 */
+#define            USB_EP_NI5_RXINTERVAL  0xffc03b60   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint5 */
+#define               USB_EP_NI5_TXCOUNT  0xffc03b68   /* Number of bytes to be written to the endpoint5 Tx FIFO */
+
+/* USB Endpoint 6 Control Registers */
+
+#define                USB_EP_NI6_TXMAXP  0xffc03b80   /* Maximum packet size for Host Tx endpoint6 */
+#define                 USB_EP_NI6_TXCSR  0xffc03b84   /* Control Status register for endpoint6 */
+#define                USB_EP_NI6_RXMAXP  0xffc03b88   /* Maximum packet size for Host Rx endpoint6 */
+#define                 USB_EP_NI6_RXCSR  0xffc03b8c   /* Control Status register for Host Rx endpoint6 */
+#define               USB_EP_NI6_RXCOUNT  0xffc03b90   /* Number of bytes received in endpoint6 FIFO */
+#define                USB_EP_NI6_TXTYPE  0xffc03b94   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint6 */
+#define            USB_EP_NI6_TXINTERVAL  0xffc03b98   /* Sets the NAK response timeout on Endpoint6 */
+#define                USB_EP_NI6_RXTYPE  0xffc03b9c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint6 */
+#define            USB_EP_NI6_RXINTERVAL  0xffc03ba0   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint6 */
+#define               USB_EP_NI6_TXCOUNT  0xffc03ba8   /* Number of bytes to be written to the endpoint6 Tx FIFO */
+
+/* USB Endpoint 7 Control Registers */
+
+#define                USB_EP_NI7_TXMAXP  0xffc03bc0   /* Maximum packet size for Host Tx endpoint7 */
+#define                 USB_EP_NI7_TXCSR  0xffc03bc4   /* Control Status register for endpoint7 */
+#define                USB_EP_NI7_RXMAXP  0xffc03bc8   /* Maximum packet size for Host Rx endpoint7 */
+#define                 USB_EP_NI7_RXCSR  0xffc03bcc   /* Control Status register for Host Rx endpoint7 */
+#define               USB_EP_NI7_RXCOUNT  0xffc03bd0   /* Number of bytes received in endpoint7 FIFO */
+#define                USB_EP_NI7_TXTYPE  0xffc03bd4   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint7 */
+#define            USB_EP_NI7_TXINTERVAL  0xffc03bd8   /* Sets the NAK response timeout on Endpoint7 */
+#define                USB_EP_NI7_RXTYPE  0xffc03bdc   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint7 */
+#define            USB_EP_NI7_RXINTERVAL  0xffc03bf0   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint7 */
+#define               USB_EP_NI7_TXCOUNT  0xffc03bf8   /* Number of bytes to be written to the endpoint7 Tx FIFO */
+
+#define                USB_DMA_INTERRUPT  0xffc03c00   /* Indicates pending interrupts for the DMA channels */
+
+/* USB Channel 0 Config Registers */
+
+#define                  USB_DMA0CONTROL  0xffc03c04   /* DMA master channel 0 configuration */
+#define                  USB_DMA0ADDRLOW  0xffc03c08   /* Lower 16-bits of memory source/destination address for DMA master channel 0 */
+#define                 USB_DMA0ADDRHIGH  0xffc03c0c   /* Upper 16-bits of memory source/destination address for DMA master channel 0 */
+#define                 USB_DMA0COUNTLOW  0xffc03c10   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 0 */
+#define                USB_DMA0COUNTHIGH  0xffc03c14   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 0 */
+
+/* USB Channel 1 Config Registers */
+
+#define                  USB_DMA1CONTROL  0xffc03c24   /* DMA master channel 1 configuration */
+#define                  USB_DMA1ADDRLOW  0xffc03c28   /* Lower 16-bits of memory source/destination address for DMA master channel 1 */
+#define                 USB_DMA1ADDRHIGH  0xffc03c2c   /* Upper 16-bits of memory source/destination address for DMA master channel 1 */
+#define                 USB_DMA1COUNTLOW  0xffc03c30   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 1 */
+#define                USB_DMA1COUNTHIGH  0xffc03c34   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 1 */
+
+/* USB Channel 2 Config Registers */
+
+#define                  USB_DMA2CONTROL  0xffc03c44   /* DMA master channel 2 configuration */
+#define                  USB_DMA2ADDRLOW  0xffc03c48   /* Lower 16-bits of memory source/destination address for DMA master channel 2 */
+#define                 USB_DMA2ADDRHIGH  0xffc03c4c   /* Upper 16-bits of memory source/destination address for DMA master channel 2 */
+#define                 USB_DMA2COUNTLOW  0xffc03c50   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 2 */
+#define                USB_DMA2COUNTHIGH  0xffc03c54   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 2 */
+
+/* USB Channel 3 Config Registers */
+
+#define                  USB_DMA3CONTROL  0xffc03c64   /* DMA master channel 3 configuration */
+#define                  USB_DMA3ADDRLOW  0xffc03c68   /* Lower 16-bits of memory source/destination address for DMA master channel 3 */
+#define                 USB_DMA3ADDRHIGH  0xffc03c6c   /* Upper 16-bits of memory source/destination address for DMA master channel 3 */
+#define                 USB_DMA3COUNTLOW  0xffc03c70   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 3 */
+#define                USB_DMA3COUNTHIGH  0xffc03c74   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 3 */
+
+/* USB Channel 4 Config Registers */
+
+#define                  USB_DMA4CONTROL  0xffc03c84   /* DMA master channel 4 configuration */
+#define                  USB_DMA4ADDRLOW  0xffc03c88   /* Lower 16-bits of memory source/destination address for DMA master channel 4 */
+#define                 USB_DMA4ADDRHIGH  0xffc03c8c   /* Upper 16-bits of memory source/destination address for DMA master channel 4 */
+#define                 USB_DMA4COUNTLOW  0xffc03c90   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 4 */
+#define                USB_DMA4COUNTHIGH  0xffc03c94   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 4 */
+
+/* USB Channel 5 Config Registers */
+
+#define                  USB_DMA5CONTROL  0xffc03ca4   /* DMA master channel 5 configuration */
+#define                  USB_DMA5ADDRLOW  0xffc03ca8   /* Lower 16-bits of memory source/destination address for DMA master channel 5 */
+#define                 USB_DMA5ADDRHIGH  0xffc03cac   /* Upper 16-bits of memory source/destination address for DMA master channel 5 */
+#define                 USB_DMA5COUNTLOW  0xffc03cb0   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 5 */
+#define                USB_DMA5COUNTHIGH  0xffc03cb4   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 5 */
+
+/* USB Channel 6 Config Registers */
+
+#define                  USB_DMA6CONTROL  0xffc03cc4   /* DMA master channel 6 configuration */
+#define                  USB_DMA6ADDRLOW  0xffc03cc8   /* Lower 16-bits of memory source/destination address for DMA master channel 6 */
+#define                 USB_DMA6ADDRHIGH  0xffc03ccc   /* Upper 16-bits of memory source/destination address for DMA master channel 6 */
+#define                 USB_DMA6COUNTLOW  0xffc03cd0   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 6 */
+#define                USB_DMA6COUNTHIGH  0xffc03cd4   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 6 */
+
+/* USB Channel 7 Config Registers */
+
+#define                  USB_DMA7CONTROL  0xffc03ce4   /* DMA master channel 7 configuration */
+#define                  USB_DMA7ADDRLOW  0xffc03ce8   /* Lower 16-bits of memory source/destination address for DMA master channel 7 */
+#define                 USB_DMA7ADDRHIGH  0xffc03cec   /* Upper 16-bits of memory source/destination address for DMA master channel 7 */
+#define                 USB_DMA7COUNTLOW  0xffc03cf0   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 7 */
+#define                USB_DMA7COUNTHIGH  0xffc03cf4   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 7 */
+
+/* Bit masks for USB_FADDR */
+
+#define          FUNCTION_ADDRESS  0x7f       /* Function address */
+
+/* Bit masks for USB_POWER */
+
+#define           ENABLE_SUSPENDM  0x1        /* enable SuspendM output */
+#define          nENABLE_SUSPENDM  0x0       
+#define              SUSPEND_MODE  0x2        /* Suspend Mode indicator */
+#define             nSUSPEND_MODE  0x0       
+#define               RESUME_MODE  0x4        /* DMA Mode */
+#define              nRESUME_MODE  0x0       
+#define                     RESET  0x8        /* Reset indicator */
+#define                    nRESET  0x0       
+#define                   HS_MODE  0x10       /* High Speed mode indicator */
+#define                  nHS_MODE  0x0       
+#define                 HS_ENABLE  0x20       /* high Speed Enable */
+#define                nHS_ENABLE  0x0       
+#define                 SOFT_CONN  0x40       /* Soft connect */
+#define                nSOFT_CONN  0x0       
+#define                ISO_UPDATE  0x80       /* Isochronous update */
+#define               nISO_UPDATE  0x0       
+
+/* Bit masks for USB_INTRTX */
+
+#define                    EP0_TX  0x1        /* Tx Endpoint 0 interrupt */
+#define                   nEP0_TX  0x0       
+#define                    EP1_TX  0x2        /* Tx Endpoint 1 interrupt */
+#define                   nEP1_TX  0x0       
+#define                    EP2_TX  0x4        /* Tx Endpoint 2 interrupt */
+#define                   nEP2_TX  0x0       
+#define                    EP3_TX  0x8        /* Tx Endpoint 3 interrupt */
+#define                   nEP3_TX  0x0       
+#define                    EP4_TX  0x10       /* Tx Endpoint 4 interrupt */
+#define                   nEP4_TX  0x0       
+#define                    EP5_TX  0x20       /* Tx Endpoint 5 interrupt */
+#define                   nEP5_TX  0x0       
+#define                    EP6_TX  0x40       /* Tx Endpoint 6 interrupt */
+#define                   nEP6_TX  0x0       
+#define                    EP7_TX  0x80       /* Tx Endpoint 7 interrupt */
+#define                   nEP7_TX  0x0       
+
+/* Bit masks for USB_INTRRX */
+
+#define                    EP1_RX  0x2        /* Rx Endpoint 1 interrupt */
+#define                   nEP1_RX  0x0       
+#define                    EP2_RX  0x4        /* Rx Endpoint 2 interrupt */
+#define                   nEP2_RX  0x0       
+#define                    EP3_RX  0x8        /* Rx Endpoint 3 interrupt */
+#define                   nEP3_RX  0x0       
+#define                    EP4_RX  0x10       /* Rx Endpoint 4 interrupt */
+#define                   nEP4_RX  0x0       
+#define                    EP5_RX  0x20       /* Rx Endpoint 5 interrupt */
+#define                   nEP5_RX  0x0       
+#define                    EP6_RX  0x40       /* Rx Endpoint 6 interrupt */
+#define                   nEP6_RX  0x0       
+#define                    EP7_RX  0x80       /* Rx Endpoint 7 interrupt */
+#define                   nEP7_RX  0x0       
+
+/* Bit masks for USB_INTRTXE */
+
+#define                  EP0_TX_E  0x1        /* Endpoint 0 interrupt Enable */
+#define                 nEP0_TX_E  0x0       
+#define                  EP1_TX_E  0x2        /* Tx Endpoint 1 interrupt  Enable */
+#define                 nEP1_TX_E  0x0       
+#define                  EP2_TX_E  0x4        /* Tx Endpoint 2 interrupt  Enable */
+#define                 nEP2_TX_E  0x0       
+#define                  EP3_TX_E  0x8        /* Tx Endpoint 3 interrupt  Enable */
+#define                 nEP3_TX_E  0x0       
+#define                  EP4_TX_E  0x10       /* Tx Endpoint 4 interrupt  Enable */
+#define                 nEP4_TX_E  0x0       
+#define                  EP5_TX_E  0x20       /* Tx Endpoint 5 interrupt  Enable */
+#define                 nEP5_TX_E  0x0       
+#define                  EP6_TX_E  0x40       /* Tx Endpoint 6 interrupt  Enable */
+#define                 nEP6_TX_E  0x0       
+#define                  EP7_TX_E  0x80       /* Tx Endpoint 7 interrupt  Enable */
+#define                 nEP7_TX_E  0x0       
+
+/* Bit masks for USB_INTRRXE */
+
+#define                  EP1_RX_E  0x2        /* Rx Endpoint 1 interrupt  Enable */
+#define                 nEP1_RX_E  0x0       
+#define                  EP2_RX_E  0x4        /* Rx Endpoint 2 interrupt  Enable */
+#define                 nEP2_RX_E  0x0       
+#define                  EP3_RX_E  0x8        /* Rx Endpoint 3 interrupt  Enable */
+#define                 nEP3_RX_E  0x0       
+#define                  EP4_RX_E  0x10       /* Rx Endpoint 4 interrupt  Enable */
+#define                 nEP4_RX_E  0x0       
+#define                  EP5_RX_E  0x20       /* Rx Endpoint 5 interrupt  Enable */
+#define                 nEP5_RX_E  0x0       
+#define                  EP6_RX_E  0x40       /* Rx Endpoint 6 interrupt  Enable */
+#define                 nEP6_RX_E  0x0       
+#define                  EP7_RX_E  0x80       /* Rx Endpoint 7 interrupt  Enable */
+#define                 nEP7_RX_E  0x0       
+
+/* Bit masks for USB_INTRUSB */
+
+#define                 SUSPEND_B  0x1        /* Suspend indicator */
+#define                nSUSPEND_B  0x0       
+#define                  RESUME_B  0x2        /* Resume indicator */
+#define                 nRESUME_B  0x0       
+#define          RESET_OR_BABLE_B  0x4        /* Reset/babble indicator */
+#define         nRESET_OR_BABLE_B  0x0       
+#define                     SOF_B  0x8        /* Start of frame */
+#define                    nSOF_B  0x0       
+#define                    CONN_B  0x10       /* Connection indicator */
+#define                   nCONN_B  0x0       
+#define                  DISCON_B  0x20       /* Disconnect indicator */
+#define                 nDISCON_B  0x0       
+#define             SESSION_REQ_B  0x40       /* Session Request */
+#define            nSESSION_REQ_B  0x0       
+#define              VBUS_ERROR_B  0x80       /* Vbus threshold indicator */
+#define             nVBUS_ERROR_B  0x0       
+
+/* Bit masks for USB_INTRUSBE */
+
+#define                SUSPEND_BE  0x1        /* Suspend indicator int enable */
+#define               nSUSPEND_BE  0x0       
+#define                 RESUME_BE  0x2        /* Resume indicator int enable */
+#define                nRESUME_BE  0x0       
+#define         RESET_OR_BABLE_BE  0x4        /* Reset/babble indicator int enable */
+#define        nRESET_OR_BABLE_BE  0x0       
+#define                    SOF_BE  0x8        /* Start of frame int enable */
+#define                   nSOF_BE  0x0       
+#define                   CONN_BE  0x10       /* Connection indicator int enable */
+#define                  nCONN_BE  0x0       
+#define                 DISCON_BE  0x20       /* Disconnect indicator int enable */
+#define                nDISCON_BE  0x0       
+#define            SESSION_REQ_BE  0x40       /* Session Request int enable */
+#define           nSESSION_REQ_BE  0x0       
+#define             VBUS_ERROR_BE  0x80       /* Vbus threshold indicator int enable */
+#define            nVBUS_ERROR_BE  0x0       
+
+/* Bit masks for USB_FRAME */
+
+#define              FRAME_NUMBER  0x7ff      /* Frame number */
+
+/* Bit masks for USB_INDEX */
+
+#define         SELECTED_ENDPOINT  0xf        /* selected endpoint */
+
+/* Bit masks for USB_GLOBAL_CTL */
+
+#define                GLOBAL_ENA  0x1        /* enables USB module */
+#define               nGLOBAL_ENA  0x0       
+#define                EP1_TX_ENA  0x2        /* Transmit endpoint 1 enable */
+#define               nEP1_TX_ENA  0x0       
+#define                EP2_TX_ENA  0x4        /* Transmit endpoint 2 enable */
+#define               nEP2_TX_ENA  0x0       
+#define                EP3_TX_ENA  0x8        /* Transmit endpoint 3 enable */
+#define               nEP3_TX_ENA  0x0       
+#define                EP4_TX_ENA  0x10       /* Transmit endpoint 4 enable */
+#define               nEP4_TX_ENA  0x0       
+#define                EP5_TX_ENA  0x20       /* Transmit endpoint 5 enable */
+#define               nEP5_TX_ENA  0x0       
+#define                EP6_TX_ENA  0x40       /* Transmit endpoint 6 enable */
+#define               nEP6_TX_ENA  0x0       
+#define                EP7_TX_ENA  0x80       /* Transmit endpoint 7 enable */
+#define               nEP7_TX_ENA  0x0       
+#define                EP1_RX_ENA  0x100      /* Receive endpoint 1 enable */
+#define               nEP1_RX_ENA  0x0       
+#define                EP2_RX_ENA  0x200      /* Receive endpoint 2 enable */
+#define               nEP2_RX_ENA  0x0       
+#define                EP3_RX_ENA  0x400      /* Receive endpoint 3 enable */
+#define               nEP3_RX_ENA  0x0       
+#define                EP4_RX_ENA  0x800      /* Receive endpoint 4 enable */
+#define               nEP4_RX_ENA  0x0       
+#define                EP5_RX_ENA  0x1000     /* Receive endpoint 5 enable */
+#define               nEP5_RX_ENA  0x0       
+#define                EP6_RX_ENA  0x2000     /* Receive endpoint 6 enable */
+#define               nEP6_RX_ENA  0x0       
+#define                EP7_RX_ENA  0x4000     /* Receive endpoint 7 enable */
+#define               nEP7_RX_ENA  0x0       
+
+/* Bit masks for USB_OTG_DEV_CTL */
+
+#define                   SESSION  0x1        /* session indicator */
+#define                  nSESSION  0x0       
+#define                  HOST_REQ  0x2        /* Host negotiation request */
+#define                 nHOST_REQ  0x0       
+#define                 HOST_MODE  0x4        /* indicates USBDRC is a host */
+#define                nHOST_MODE  0x0       
+#define                     VBUS0  0x8        /* Vbus level indicator[0] */
+#define                    nVBUS0  0x0       
+#define                     VBUS1  0x10       /* Vbus level indicator[1] */
+#define                    nVBUS1  0x0       
+#define                     LSDEV  0x20       /* Low-speed indicator */
+#define                    nLSDEV  0x0       
+#define                     FSDEV  0x40       /* Full or High-speed indicator */
+#define                    nFSDEV  0x0       
+#define                  B_DEVICE  0x80       /* A' or 'B' device indicator */
+#define                 nB_DEVICE  0x0       
+
+/* Bit masks for USB_OTG_VBUS_IRQ */
+
+#define             DRIVE_VBUS_ON  0x1        /* indicator to drive VBUS control circuit */
+#define            nDRIVE_VBUS_ON  0x0       
+#define            DRIVE_VBUS_OFF  0x2        /* indicator to shut off charge pump */
+#define           nDRIVE_VBUS_OFF  0x0       
+#define           CHRG_VBUS_START  0x4        /* indicator for external circuit to start charging VBUS */
+#define          nCHRG_VBUS_START  0x0       
+#define             CHRG_VBUS_END  0x8        /* indicator for external circuit to end charging VBUS */
+#define            nCHRG_VBUS_END  0x0       
+#define        DISCHRG_VBUS_START  0x10       /* indicator to start discharging VBUS */
+#define       nDISCHRG_VBUS_START  0x0       
+#define          DISCHRG_VBUS_END  0x20       /* indicator to stop discharging VBUS */
+#define         nDISCHRG_VBUS_END  0x0       
+
+/* Bit masks for USB_OTG_VBUS_MASK */
+
+#define         DRIVE_VBUS_ON_ENA  0x1        /* enable DRIVE_VBUS_ON interrupt */
+#define        nDRIVE_VBUS_ON_ENA  0x0       
+#define        DRIVE_VBUS_OFF_ENA  0x2        /* enable DRIVE_VBUS_OFF interrupt */
+#define       nDRIVE_VBUS_OFF_ENA  0x0       
+#define       CHRG_VBUS_START_ENA  0x4        /* enable CHRG_VBUS_START interrupt */
+#define      nCHRG_VBUS_START_ENA  0x0       
+#define         CHRG_VBUS_END_ENA  0x8        /* enable CHRG_VBUS_END interrupt */
+#define        nCHRG_VBUS_END_ENA  0x0       
+#define    DISCHRG_VBUS_START_ENA  0x10       /* enable DISCHRG_VBUS_START interrupt */
+#define   nDISCHRG_VBUS_START_ENA  0x0       
+#define      DISCHRG_VBUS_END_ENA  0x20       /* enable DISCHRG_VBUS_END interrupt */
+#define     nDISCHRG_VBUS_END_ENA  0x0       
+
+/* Bit masks for USB_CSR0 */
+
+#define                  RXPKTRDY  0x1        /* data packet receive indicator */
+#define                 nRXPKTRDY  0x0       
+#define                  TXPKTRDY  0x2        /* data packet in FIFO indicator */
+#define                 nTXPKTRDY  0x0       
+#define                STALL_SENT  0x4        /* STALL handshake sent */
+#define               nSTALL_SENT  0x0       
+#define                   DATAEND  0x8        /* Data end indicator */
+#define                  nDATAEND  0x0       
+#define                  SETUPEND  0x10       /* Setup end */
+#define                 nSETUPEND  0x0       
+#define                 SENDSTALL  0x20       /* Send STALL handshake */
+#define                nSENDSTALL  0x0       
+#define         SERVICED_RXPKTRDY  0x40       /* used to clear the RxPktRdy bit */
+#define        nSERVICED_RXPKTRDY  0x0       
+#define         SERVICED_SETUPEND  0x80       /* used to clear the SetupEnd bit */
+#define        nSERVICED_SETUPEND  0x0       
+#define                 FLUSHFIFO  0x100      /* flush endpoint FIFO */
+#define                nFLUSHFIFO  0x0       
+#define          STALL_RECEIVED_H  0x4        /* STALL handshake received host mode */
+#define         nSTALL_RECEIVED_H  0x0       
+#define                SETUPPKT_H  0x8        /* send Setup token host mode */
+#define               nSETUPPKT_H  0x0       
+#define                   ERROR_H  0x10       /* timeout error indicator host mode */
+#define                  nERROR_H  0x0       
+#define                  REQPKT_H  0x20       /* Request an IN transaction host mode */
+#define                 nREQPKT_H  0x0       
+#define               STATUSPKT_H  0x40       /* Status stage transaction host mode */
+#define              nSTATUSPKT_H  0x0       
+#define             NAK_TIMEOUT_H  0x80       /* EP0 halted after a NAK host mode */
+#define            nNAK_TIMEOUT_H  0x0       
+
+/* Bit masks for USB_COUNT0 */
+
+#define              EP0_RX_COUNT  0x7f       /* number of received bytes in EP0 FIFO */
+
+/* Bit masks for USB_NAKLIMIT0 */
+
+#define             EP0_NAK_LIMIT  0x1f       /* number of frames/micro frames after which EP0 timeouts */
+
+/* Bit masks for USB_TX_MAX_PACKET */
+
+#define         MAX_PACKET_SIZE_T  0x7ff      /* maximum data pay load in a frame */
+
+/* Bit masks for USB_RX_MAX_PACKET */
+
+#define         MAX_PACKET_SIZE_R  0x7ff      /* maximum data pay load in a frame */
+
+/* Bit masks for USB_TXCSR */
+
+#define                TXPKTRDY_T  0x1        /* data packet in FIFO indicator */
+#define               nTXPKTRDY_T  0x0       
+#define          FIFO_NOT_EMPTY_T  0x2        /* FIFO not empty */
+#define         nFIFO_NOT_EMPTY_T  0x0       
+#define                UNDERRUN_T  0x4        /* TxPktRdy not set  for an IN token */
+#define               nUNDERRUN_T  0x0       
+#define               FLUSHFIFO_T  0x8        /* flush endpoint FIFO */
+#define              nFLUSHFIFO_T  0x0       
+#define              STALL_SEND_T  0x10       /* issue a Stall handshake */
+#define             nSTALL_SEND_T  0x0       
+#define              STALL_SENT_T  0x20       /* Stall handshake transmitted */
+#define             nSTALL_SENT_T  0x0       
+#define        CLEAR_DATATOGGLE_T  0x40       /* clear endpoint data toggle */
+#define       nCLEAR_DATATOGGLE_T  0x0       
+#define                INCOMPTX_T  0x80       /* indicates that a large packet is split */
+#define               nINCOMPTX_T  0x0       
+#define              DMAREQMODE_T  0x400      /* DMA mode (0 or 1) selection */
+#define             nDMAREQMODE_T  0x0       
+#define        FORCE_DATATOGGLE_T  0x800      /* Force data toggle */
+#define       nFORCE_DATATOGGLE_T  0x0       
+#define              DMAREQ_ENA_T  0x1000     /* Enable DMA request for Tx EP */
+#define             nDMAREQ_ENA_T  0x0       
+#define                     ISO_T  0x4000     /* enable Isochronous transfers */
+#define                    nISO_T  0x0       
+#define                 AUTOSET_T  0x8000     /* allows TxPktRdy to be set automatically */
+#define                nAUTOSET_T  0x0       
+#define                  ERROR_TH  0x4        /* error condition host mode */
+#define                 nERROR_TH  0x0       
+#define         STALL_RECEIVED_TH  0x20       /* Stall handshake received host mode */
+#define        nSTALL_RECEIVED_TH  0x0       
+#define            NAK_TIMEOUT_TH  0x80       /* NAK timeout host mode */
+#define           nNAK_TIMEOUT_TH  0x0       
+
+/* Bit masks for USB_TXCOUNT */
+
+#define                  TX_COUNT  0x1fff     /* Number of bytes to be written to the selected endpoint Tx FIFO */
+
+/* Bit masks for USB_RXCSR */
+
+#define                RXPKTRDY_R  0x1        /* data packet in FIFO indicator */
+#define               nRXPKTRDY_R  0x0       
+#define               FIFO_FULL_R  0x2        /* FIFO not empty */
+#define              nFIFO_FULL_R  0x0       
+#define                 OVERRUN_R  0x4        /* TxPktRdy not set  for an IN token */
+#define                nOVERRUN_R  0x0       
+#define               DATAERROR_R  0x8        /* Out packet cannot be loaded into Rx  FIFO */
+#define              nDATAERROR_R  0x0       
+#define               FLUSHFIFO_R  0x10       /* flush endpoint FIFO */
+#define              nFLUSHFIFO_R  0x0       
+#define              STALL_SEND_R  0x20       /* issue a Stall handshake */
+#define             nSTALL_SEND_R  0x0       
+#define              STALL_SENT_R  0x40       /* Stall handshake transmitted */
+#define             nSTALL_SENT_R  0x0       
+#define        CLEAR_DATATOGGLE_R  0x80       /* clear endpoint data toggle */
+#define       nCLEAR_DATATOGGLE_R  0x0       
+#define                INCOMPRX_R  0x100      /* indicates that a large packet is split */
+#define               nINCOMPRX_R  0x0       
+#define              DMAREQMODE_R  0x800      /* DMA mode (0 or 1) selection */
+#define             nDMAREQMODE_R  0x0       
+#define                 DISNYET_R  0x1000     /* disable Nyet handshakes */
+#define                nDISNYET_R  0x0       
+#define              DMAREQ_ENA_R  0x2000     /* Enable DMA request for Tx EP */
+#define             nDMAREQ_ENA_R  0x0       
+#define                     ISO_R  0x4000     /* enable Isochronous transfers */
+#define                    nISO_R  0x0       
+#define               AUTOCLEAR_R  0x8000     /* allows TxPktRdy to be set automatically */
+#define              nAUTOCLEAR_R  0x0       
+#define                  ERROR_RH  0x4        /* TxPktRdy not set  for an IN token host mode */
+#define                 nERROR_RH  0x0       
+#define                 REQPKT_RH  0x20       /* request an IN transaction host mode */
+#define                nREQPKT_RH  0x0       
+#define         STALL_RECEIVED_RH  0x40       /* Stall handshake received host mode */
+#define        nSTALL_RECEIVED_RH  0x0       
+#define               INCOMPRX_RH  0x100      /* indicates that a large packet is split host mode */
+#define              nINCOMPRX_RH  0x0       
+#define             DMAREQMODE_RH  0x800      /* DMA mode (0 or 1) selection host mode */
+#define            nDMAREQMODE_RH  0x0       
+#define                AUTOREQ_RH  0x4000     /* sets ReqPkt automatically host mode */
+#define               nAUTOREQ_RH  0x0       
+
+/* Bit masks for USB_RXCOUNT */
+
+#define                  RX_COUNT  0x1fff     /* Number of received bytes in the packet in the Rx FIFO */
+
+/* Bit masks for USB_TXTYPE */
+
+#define            TARGET_EP_NO_T  0xf        /* EP number */
+#define                PROTOCOL_T  0xc        /* transfer type */
+
+/* Bit masks for USB_TXINTERVAL */
+
+#define          TX_POLL_INTERVAL  0xff       /* polling interval for selected Tx EP */
+
+/* Bit masks for USB_RXTYPE */
+
+#define            TARGET_EP_NO_R  0xf        /* EP number */
+#define                PROTOCOL_R  0xc        /* transfer type */
+
+/* Bit masks for USB_RXINTERVAL */
+
+#define          RX_POLL_INTERVAL  0xff       /* polling interval for selected Rx EP */
+
+/* Bit masks for USB_DMA_INTERRUPT */
+
+#define                  DMA0_INT  0x1        /* DMA0 pending interrupt */
+#define                 nDMA0_INT  0x0       
+#define                  DMA1_INT  0x2        /* DMA1 pending interrupt */
+#define                 nDMA1_INT  0x0       
+#define                  DMA2_INT  0x4        /* DMA2 pending interrupt */
+#define                 nDMA2_INT  0x0       
+#define                  DMA3_INT  0x8        /* DMA3 pending interrupt */
+#define                 nDMA3_INT  0x0       
+#define                  DMA4_INT  0x10       /* DMA4 pending interrupt */
+#define                 nDMA4_INT  0x0       
+#define                  DMA5_INT  0x20       /* DMA5 pending interrupt */
+#define                 nDMA5_INT  0x0       
+#define                  DMA6_INT  0x40       /* DMA6 pending interrupt */
+#define                 nDMA6_INT  0x0       
+#define                  DMA7_INT  0x80       /* DMA7 pending interrupt */
+#define                 nDMA7_INT  0x0       
+
+/* Bit masks for USB_DMAxCONTROL */
+
+#define                   DMA_ENA  0x1        /* DMA enable */
+#define                  nDMA_ENA  0x0       
+#define                 DIRECTION  0x2        /* direction of DMA transfer */
+#define                nDIRECTION  0x0       
+#define                      MODE  0x4        /* DMA Bus error */
+#define                     nMODE  0x0       
+#define                   INT_ENA  0x8        /* Interrupt enable */
+#define                  nINT_ENA  0x0       
+#define                     EPNUM  0xf0       /* EP number */
+#define                  BUSERROR  0x100      /* DMA Bus error */
+#define                 nBUSERROR  0x0       
+
+/* Bit masks for USB_DMAxADDRHIGH */
+
+#define             DMA_ADDR_HIGH  0xffff     /* Upper 16-bits of memory source/destination address for the DMA master channel */
+
+/* Bit masks for USB_DMAxADDRLOW */
+
+#define              DMA_ADDR_LOW  0xffff     /* Lower 16-bits of memory source/destination address for the DMA master channel */
+
+/* Bit masks for USB_DMAxCOUNTHIGH */
+
+#define            DMA_COUNT_HIGH  0xffff     /* Upper 16-bits of byte count of DMA transfer for DMA master channel */
+
+/* Bit masks for USB_DMAxCOUNTLOW */
+
+#define             DMA_COUNT_LOW  0xffff     /* Lower 16-bits of byte count of DMA transfer for DMA master channel */
+
+#endif /* _DEF_BF525_H */
diff --git a/arch/blackfin/mach-bf527/include/mach/defBF527.h b/arch/blackfin/mach-bf527/include/mach/defBF527.h
new file mode 100644
index 00000000000..f040f364afa
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/defBF527.h
@@ -0,0 +1,1090 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/defBF527.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _DEF_BF527_H
+#define _DEF_BF527_H
+
+/* Include all Core registers and bit definitions */
+#include <asm/def_LPBlackfin.h>
+
+/* SYSTEM & MMR ADDRESS DEFINITIONS FOR ADSP-BF527 */
+
+/* Include defBF52x_base.h for the set of #defines that are common to all ADSP-BF52x processors */
+#include "defBF52x_base.h"
+
+/* The following are the #defines needed by ADSP-BF527 that are not in the common header */
+/* 10/100 Ethernet Controller	(0xFFC03000 - 0xFFC031FF) */
+
+#define EMAC_OPMODE             0xFFC03000       /* Operating Mode Register                              */
+#define EMAC_ADDRLO             0xFFC03004       /* Address Low (32 LSBs) Register                       */
+#define EMAC_ADDRHI             0xFFC03008       /* Address High (16 MSBs) Register                      */
+#define EMAC_HASHLO             0xFFC0300C       /* Multicast Hash Table Low (Bins 31-0) Register        */
+#define EMAC_HASHHI             0xFFC03010       /* Multicast Hash Table High (Bins 63-32) Register      */
+#define EMAC_STAADD             0xFFC03014       /* Station Management Address Register                  */
+#define EMAC_STADAT             0xFFC03018       /* Station Management Data Register                     */
+#define EMAC_FLC                0xFFC0301C       /* Flow Control Register                                */
+#define EMAC_VLAN1              0xFFC03020       /* VLAN1 Tag Register                                   */
+#define EMAC_VLAN2              0xFFC03024       /* VLAN2 Tag Register                                   */
+#define EMAC_WKUP_CTL           0xFFC0302C       /* Wake-Up Control/Status Register                      */
+#define EMAC_WKUP_FFMSK0        0xFFC03030       /* Wake-Up Frame Filter 0 Byte Mask Register            */
+#define EMAC_WKUP_FFMSK1        0xFFC03034       /* Wake-Up Frame Filter 1 Byte Mask Register            */
+#define EMAC_WKUP_FFMSK2        0xFFC03038       /* Wake-Up Frame Filter 2 Byte Mask Register            */
+#define EMAC_WKUP_FFMSK3        0xFFC0303C       /* Wake-Up Frame Filter 3 Byte Mask Register            */
+#define EMAC_WKUP_FFCMD         0xFFC03040       /* Wake-Up Frame Filter Commands Register               */
+#define EMAC_WKUP_FFOFF         0xFFC03044       /* Wake-Up Frame Filter Offsets Register                */
+#define EMAC_WKUP_FFCRC0        0xFFC03048       /* Wake-Up Frame Filter 0,1 CRC-16 Register             */
+#define EMAC_WKUP_FFCRC1        0xFFC0304C       /* Wake-Up Frame Filter 2,3 CRC-16 Register             */
+
+#define EMAC_SYSCTL             0xFFC03060       /* EMAC System Control Register                         */
+#define EMAC_SYSTAT             0xFFC03064       /* EMAC System Status Register                          */
+#define EMAC_RX_STAT            0xFFC03068       /* RX Current Frame Status Register                     */
+#define EMAC_RX_STKY            0xFFC0306C       /* RX Sticky Frame Status Register                      */
+#define EMAC_RX_IRQE            0xFFC03070       /* RX Frame Status Interrupt Enables Register           */
+#define EMAC_TX_STAT            0xFFC03074       /* TX Current Frame Status Register                     */
+#define EMAC_TX_STKY            0xFFC03078       /* TX Sticky Frame Status Register                      */
+#define EMAC_TX_IRQE            0xFFC0307C       /* TX Frame Status Interrupt Enables Register           */
+
+#define EMAC_MMC_CTL            0xFFC03080       /* MMC Counter Control Register                         */
+#define EMAC_MMC_RIRQS          0xFFC03084       /* MMC RX Interrupt Status Register                     */
+#define EMAC_MMC_RIRQE          0xFFC03088       /* MMC RX Interrupt Enables Register                    */
+#define EMAC_MMC_TIRQS          0xFFC0308C       /* MMC TX Interrupt Status Register                     */
+#define EMAC_MMC_TIRQE          0xFFC03090       /* MMC TX Interrupt Enables Register                    */
+
+#define EMAC_RXC_OK             0xFFC03100       /* RX Frame Successful Count                            */
+#define EMAC_RXC_FCS            0xFFC03104       /* RX Frame FCS Failure Count                           */
+#define EMAC_RXC_ALIGN          0xFFC03108       /* RX Alignment Error Count                             */
+#define EMAC_RXC_OCTET          0xFFC0310C       /* RX Octets Successfully Received Count                */
+#define EMAC_RXC_DMAOVF         0xFFC03110       /* Internal MAC Sublayer Error RX Frame Count           */
+#define EMAC_RXC_UNICST         0xFFC03114       /* Unicast RX Frame Count                               */
+#define EMAC_RXC_MULTI          0xFFC03118       /* Multicast RX Frame Count                             */
+#define EMAC_RXC_BROAD          0xFFC0311C       /* Broadcast RX Frame Count                             */
+#define EMAC_RXC_LNERRI         0xFFC03120       /* RX Frame In Range Error Count                        */
+#define EMAC_RXC_LNERRO         0xFFC03124       /* RX Frame Out Of Range Error Count                    */
+#define EMAC_RXC_LONG           0xFFC03128       /* RX Frame Too Long Count                              */
+#define EMAC_RXC_MACCTL         0xFFC0312C       /* MAC Control RX Frame Count                           */
+#define EMAC_RXC_OPCODE         0xFFC03130       /* Unsupported Op-Code RX Frame Count                   */
+#define EMAC_RXC_PAUSE          0xFFC03134       /* MAC Control Pause RX Frame Count                     */
+#define EMAC_RXC_ALLFRM         0xFFC03138       /* Overall RX Frame Count                               */
+#define EMAC_RXC_ALLOCT         0xFFC0313C       /* Overall RX Octet Count                               */
+#define EMAC_RXC_TYPED          0xFFC03140       /* Type/Length Consistent RX Frame Count                */
+#define EMAC_RXC_SHORT          0xFFC03144       /* RX Frame Fragment Count - Byte Count x < 64          */
+#define EMAC_RXC_EQ64           0xFFC03148       /* Good RX Frame Count - Byte Count x = 64              */
+#define EMAC_RXC_LT128          0xFFC0314C       /* Good RX Frame Count - Byte Count  64 < x < 128       */
+#define EMAC_RXC_LT256          0xFFC03150       /* Good RX Frame Count - Byte Count 128 <= x < 256      */
+#define EMAC_RXC_LT512          0xFFC03154       /* Good RX Frame Count - Byte Count 256 <= x < 512      */
+#define EMAC_RXC_LT1024         0xFFC03158       /* Good RX Frame Count - Byte Count 512 <= x < 1024     */
+#define EMAC_RXC_GE1024         0xFFC0315C       /* Good RX Frame Count - Byte Count x >= 1024           */
+
+#define EMAC_TXC_OK             0xFFC03180       /* TX Frame Successful Count                             */
+#define EMAC_TXC_1COL           0xFFC03184       /* TX Frames Successful After Single Collision Count     */
+#define EMAC_TXC_GT1COL         0xFFC03188       /* TX Frames Successful After Multiple Collisions Count  */
+#define EMAC_TXC_OCTET          0xFFC0318C       /* TX Octets Successfully Received Count                 */
+#define EMAC_TXC_DEFER          0xFFC03190       /* TX Frame Delayed Due To Busy Count                    */
+#define EMAC_TXC_LATECL         0xFFC03194       /* Late TX Collisions Count                              */
+#define EMAC_TXC_XS_COL         0xFFC03198       /* TX Frame Failed Due To Excessive Collisions Count     */
+#define EMAC_TXC_DMAUND         0xFFC0319C       /* Internal MAC Sublayer Error TX Frame Count            */
+#define EMAC_TXC_CRSERR         0xFFC031A0       /* Carrier Sense Deasserted During TX Frame Count        */
+#define EMAC_TXC_UNICST         0xFFC031A4       /* Unicast TX Frame Count                                */
+#define EMAC_TXC_MULTI          0xFFC031A8       /* Multicast TX Frame Count                              */
+#define EMAC_TXC_BROAD          0xFFC031AC       /* Broadcast TX Frame Count                              */
+#define EMAC_TXC_XS_DFR         0xFFC031B0       /* TX Frames With Excessive Deferral Count               */
+#define EMAC_TXC_MACCTL         0xFFC031B4       /* MAC Control TX Frame Count                            */
+#define EMAC_TXC_ALLFRM         0xFFC031B8       /* Overall TX Frame Count                                */
+#define EMAC_TXC_ALLOCT         0xFFC031BC       /* Overall TX Octet Count                                */
+#define EMAC_TXC_EQ64           0xFFC031C0       /* Good TX Frame Count - Byte Count x = 64               */
+#define EMAC_TXC_LT128          0xFFC031C4       /* Good TX Frame Count - Byte Count  64 < x < 128        */
+#define EMAC_TXC_LT256          0xFFC031C8       /* Good TX Frame Count - Byte Count 128 <= x < 256       */
+#define EMAC_TXC_LT512          0xFFC031CC       /* Good TX Frame Count - Byte Count 256 <= x < 512       */
+#define EMAC_TXC_LT1024         0xFFC031D0       /* Good TX Frame Count - Byte Count 512 <= x < 1024      */
+#define EMAC_TXC_GE1024         0xFFC031D4       /* Good TX Frame Count - Byte Count x >= 1024            */
+#define EMAC_TXC_ABORT          0xFFC031D8       /* Total TX Frames Aborted Count                         */
+
+/* Listing for IEEE-Supported Count Registers */
+
+#define FramesReceivedOK                EMAC_RXC_OK        /* RX Frame Successful Count                            */
+#define FrameCheckSequenceErrors        EMAC_RXC_FCS       /* RX Frame FCS Failure Count                           */
+#define AlignmentErrors                 EMAC_RXC_ALIGN     /* RX Alignment Error Count                             */
+#define OctetsReceivedOK                EMAC_RXC_OCTET     /* RX Octets Successfully Received Count                */
+#define FramesLostDueToIntMACRcvError   EMAC_RXC_DMAOVF    /* Internal MAC Sublayer Error RX Frame Count           */
+#define UnicastFramesReceivedOK         EMAC_RXC_UNICST    /* Unicast RX Frame Count                               */
+#define MulticastFramesReceivedOK       EMAC_RXC_MULTI     /* Multicast RX Frame Count                             */
+#define BroadcastFramesReceivedOK       EMAC_RXC_BROAD     /* Broadcast RX Frame Count                             */
+#define InRangeLengthErrors             EMAC_RXC_LNERRI    /* RX Frame In Range Error Count                        */
+#define OutOfRangeLengthField           EMAC_RXC_LNERRO    /* RX Frame Out Of Range Error Count                    */
+#define FrameTooLongErrors              EMAC_RXC_LONG      /* RX Frame Too Long Count                              */
+#define MACControlFramesReceived        EMAC_RXC_MACCTL    /* MAC Control RX Frame Count                           */
+#define UnsupportedOpcodesReceived      EMAC_RXC_OPCODE    /* Unsupported Op-Code RX Frame Count                   */
+#define PAUSEMACCtrlFramesReceived      EMAC_RXC_PAUSE     /* MAC Control Pause RX Frame Count                     */
+#define FramesReceivedAll               EMAC_RXC_ALLFRM    /* Overall RX Frame Count                               */
+#define OctetsReceivedAll               EMAC_RXC_ALLOCT    /* Overall RX Octet Count                               */
+#define TypedFramesReceived             EMAC_RXC_TYPED     /* Type/Length Consistent RX Frame Count                */
+#define FramesLenLt64Received           EMAC_RXC_SHORT     /* RX Frame Fragment Count - Byte Count x < 64          */
+#define FramesLenEq64Received           EMAC_RXC_EQ64      /* Good RX Frame Count - Byte Count x = 64              */
+#define FramesLen65_127Received         EMAC_RXC_LT128     /* Good RX Frame Count - Byte Count  64 < x < 128       */
+#define FramesLen128_255Received        EMAC_RXC_LT256     /* Good RX Frame Count - Byte Count 128 <= x < 256      */
+#define FramesLen256_511Received        EMAC_RXC_LT512     /* Good RX Frame Count - Byte Count 256 <= x < 512      */
+#define FramesLen512_1023Received       EMAC_RXC_LT1024    /* Good RX Frame Count - Byte Count 512 <= x < 1024     */
+#define FramesLen1024_MaxReceived       EMAC_RXC_GE1024    /* Good RX Frame Count - Byte Count x >= 1024           */
+
+#define FramesTransmittedOK             EMAC_TXC_OK        /* TX Frame Successful Count                            */
+#define SingleCollisionFrames           EMAC_TXC_1COL      /* TX Frames Successful After Single Collision Count    */
+#define MultipleCollisionFrames         EMAC_TXC_GT1COL    /* TX Frames Successful After Multiple Collisions Count */
+#define OctetsTransmittedOK             EMAC_TXC_OCTET     /* TX Octets Successfully Received Count                */
+#define FramesWithDeferredXmissions     EMAC_TXC_DEFER     /* TX Frame Delayed Due To Busy Count                   */
+#define LateCollisions                  EMAC_TXC_LATECL    /* Late TX Collisions Count                             */
+#define FramesAbortedDueToXSColls       EMAC_TXC_XS_COL    /* TX Frame Failed Due To Excessive Collisions Count    */
+#define FramesLostDueToIntMacXmitError  EMAC_TXC_DMAUND    /* Internal MAC Sublayer Error TX Frame Count           */
+#define CarrierSenseErrors              EMAC_TXC_CRSERR    /* Carrier Sense Deasserted During TX Frame Count       */
+#define UnicastFramesXmittedOK          EMAC_TXC_UNICST    /* Unicast TX Frame Count                               */
+#define MulticastFramesXmittedOK        EMAC_TXC_MULTI     /* Multicast TX Frame Count                             */
+#define BroadcastFramesXmittedOK        EMAC_TXC_BROAD     /* Broadcast TX Frame Count                             */
+#define FramesWithExcessiveDeferral     EMAC_TXC_XS_DFR    /* TX Frames With Excessive Deferral Count              */
+#define MACControlFramesTransmitted     EMAC_TXC_MACCTL    /* MAC Control TX Frame Count                           */
+#define FramesTransmittedAll            EMAC_TXC_ALLFRM    /* Overall TX Frame Count                               */
+#define OctetsTransmittedAll            EMAC_TXC_ALLOCT    /* Overall TX Octet Count                               */
+#define FramesLenEq64Transmitted        EMAC_TXC_EQ64      /* Good TX Frame Count - Byte Count x = 64              */
+#define FramesLen65_127Transmitted      EMAC_TXC_LT128     /* Good TX Frame Count - Byte Count  64 < x < 128       */
+#define FramesLen128_255Transmitted     EMAC_TXC_LT256     /* Good TX Frame Count - Byte Count 128 <= x < 256      */
+#define FramesLen256_511Transmitted     EMAC_TXC_LT512     /* Good TX Frame Count - Byte Count 256 <= x < 512      */
+#define FramesLen512_1023Transmitted    EMAC_TXC_LT1024    /* Good TX Frame Count - Byte Count 512 <= x < 1024     */
+#define FramesLen1024_MaxTransmitted    EMAC_TXC_GE1024    /* Good TX Frame Count - Byte Count x >= 1024           */
+#define TxAbortedFrames                 EMAC_TXC_ABORT     /* Total TX Frames Aborted Count                        */
+
+/***********************************************************************************
+** System MMR Register Bits And Macros
+**
+** Disclaimer:	All macros are intended to make C and Assembly code more readable.
+**				Use these macros carefully, as any that do left shifts for field
+**				depositing will result in the lower order bits being destroyed.  Any
+**				macro that shifts left to properly position the bit-field should be
+**				used as part of an OR to initialize a register and NOT as a dynamic
+**				modifier UNLESS the lower order bits are saved and ORed back in when
+**				the macro is used.
+*************************************************************************************/
+
+/************************  ETHERNET 10/100 CONTROLLER MASKS  ************************/
+
+/* EMAC_OPMODE Masks */
+
+#define	RE                 0x00000001     /* Receiver Enable                                    */
+#define	ASTP               0x00000002     /* Enable Automatic Pad Stripping On RX Frames        */
+#define	HU                 0x00000010     /* Hash Filter Unicast Address                        */
+#define	HM                 0x00000020     /* Hash Filter Multicast Address                      */
+#define	PAM                0x00000040     /* Pass-All-Multicast Mode Enable                     */
+#define	PR                 0x00000080     /* Promiscuous Mode Enable                            */
+#define	IFE                0x00000100     /* Inverse Filtering Enable                           */
+#define	DBF                0x00000200     /* Disable Broadcast Frame Reception                  */
+#define	PBF                0x00000400     /* Pass Bad Frames Enable                             */
+#define	PSF                0x00000800     /* Pass Short Frames Enable                           */
+#define	RAF                0x00001000     /* Receive-All Mode                                   */
+#define	TE                 0x00010000     /* Transmitter Enable                                 */
+#define	DTXPAD             0x00020000     /* Disable Automatic TX Padding                       */
+#define	DTXCRC             0x00040000     /* Disable Automatic TX CRC Generation                */
+#define	DC                 0x00080000     /* Deferral Check                                     */
+#define	BOLMT              0x00300000     /* Back-Off Limit                                     */
+#define	BOLMT_10           0x00000000     /*		10-bit range                            */
+#define	BOLMT_8            0x00100000     /*		8-bit range                             */
+#define	BOLMT_4            0x00200000     /*		4-bit range                             */
+#define	BOLMT_1            0x00300000     /*		1-bit range                             */
+#define	DRTY               0x00400000     /* Disable TX Retry On Collision                      */
+#define	LCTRE              0x00800000     /* Enable TX Retry On Late Collision                  */
+#define	RMII               0x01000000     /* RMII/MII* Mode                                     */
+#define	RMII_10            0x02000000     /* Speed Select for RMII Port (10MBit/100MBit*)       */
+#define	FDMODE             0x04000000     /* Duplex Mode Enable (Full/Half*)                    */
+#define	LB                 0x08000000     /* Internal Loopback Enable                           */
+#define	DRO                0x10000000     /* Disable Receive Own Frames (Half-Duplex Mode)      */
+
+/* EMAC_STAADD Masks */
+
+#define	STABUSY            0x00000001     /* Initiate Station Mgt Reg Access / STA Busy Stat    */
+#define	STAOP              0x00000002     /* Station Management Operation Code (Write/Read*)    */
+#define	STADISPRE          0x00000004     /* Disable Preamble Generation                        */
+#define	STAIE              0x00000008     /* Station Mgt. Transfer Done Interrupt Enable        */
+#define	REGAD              0x000007C0     /* STA Register Address                               */
+#define	PHYAD              0x0000F800     /* PHY Device Address                                 */
+
+#define	SET_REGAD(x) (((x)&0x1F)<<  6 )   /* Set STA Register Address                           */
+#define	SET_PHYAD(x) (((x)&0x1F)<< 11 )   /* Set PHY Device Address                             */
+
+/* EMAC_STADAT Mask */
+
+#define	STADATA            0x0000FFFF     /* Station Management Data                            */
+
+/* EMAC_FLC Masks */
+
+#define	FLCBUSY            0x00000001     /* Send Flow Ctrl Frame / Flow Ctrl Busy Status       */
+#define	FLCE               0x00000002     /* Flow Control Enable                                */
+#define	PCF                0x00000004     /* Pass Control Frames                                */
+#define	BKPRSEN            0x00000008     /* Enable Backpressure                                */
+#define	FLCPAUSE           0xFFFF0000     /* Pause Time                                         */
+
+#define	SET_FLCPAUSE(x) (((x)&0xFFFF)<< 16) /* Set Pause Time                                   */
+
+/* EMAC_WKUP_CTL Masks */
+
+#define	CAPWKFRM           0x00000001    /* Capture Wake-Up Frames                              */
+#define	MPKE               0x00000002    /* Magic Packet Enable                                 */
+#define	RWKE               0x00000004    /* Remote Wake-Up Frame Enable                         */
+#define	GUWKE              0x00000008    /* Global Unicast Wake Enable                          */
+#define	MPKS               0x00000020    /* Magic Packet Received Status                        */
+#define	RWKS               0x00000F00    /* Wake-Up Frame Received Status, Filters 3:0          */
+
+/* EMAC_WKUP_FFCMD Masks */
+
+#define	WF0_E              0x00000001    /* Enable Wake-Up Filter 0                              */
+#define	WF0_T              0x00000008    /* Wake-Up Filter 0 Addr Type (Multicast/Unicast*)      */
+#define	WF1_E              0x00000100    /* Enable Wake-Up Filter 1                              */
+#define	WF1_T              0x00000800    /* Wake-Up Filter 1 Addr Type (Multicast/Unicast*)      */
+#define	WF2_E              0x00010000    /* Enable Wake-Up Filter 2                              */
+#define	WF2_T              0x00080000    /* Wake-Up Filter 2 Addr Type (Multicast/Unicast*)      */
+#define	WF3_E              0x01000000    /* Enable Wake-Up Filter 3                              */
+#define	WF3_T              0x08000000    /* Wake-Up Filter 3 Addr Type (Multicast/Unicast*)      */
+
+/* EMAC_WKUP_FFOFF Masks */
+
+#define	WF0_OFF            0x000000FF    /* Wake-Up Filter 0 Pattern Offset                      */
+#define	WF1_OFF            0x0000FF00    /* Wake-Up Filter 1 Pattern Offset                      */
+#define	WF2_OFF            0x00FF0000    /* Wake-Up Filter 2 Pattern Offset                      */
+#define	WF3_OFF            0xFF000000    /* Wake-Up Filter 3 Pattern Offset                      */
+
+#define	SET_WF0_OFF(x) (((x)&0xFF)<<  0 ) /* Set Wake-Up Filter 0 Byte Offset                    */
+#define	SET_WF1_OFF(x) (((x)&0xFF)<<  8 ) /* Set Wake-Up Filter 1 Byte Offset                    */
+#define	SET_WF2_OFF(x) (((x)&0xFF)<< 16 ) /* Set Wake-Up Filter 2 Byte Offset                    */
+#define	SET_WF3_OFF(x) (((x)&0xFF)<< 24 ) /* Set Wake-Up Filter 3 Byte Offset                    */
+/* Set ALL Offsets */
+#define	SET_WF_OFFS(x0,x1,x2,x3) (SET_WF0_OFF((x0))|SET_WF1_OFF((x1))|SET_WF2_OFF((x2))|SET_WF3_OFF((x3)))
+
+/* EMAC_WKUP_FFCRC0 Masks */
+
+#define	WF0_CRC           0x0000FFFF    /* Wake-Up Filter 0 Pattern CRC                           */
+#define	WF1_CRC           0xFFFF0000    /* Wake-Up Filter 1 Pattern CRC                           */
+
+#define	SET_WF0_CRC(x) (((x)&0xFFFF)<<   0 ) /* Set Wake-Up Filter 0 Target CRC                   */
+#define	SET_WF1_CRC(x) (((x)&0xFFFF)<<  16 ) /* Set Wake-Up Filter 1 Target CRC                   */
+
+/* EMAC_WKUP_FFCRC1 Masks */
+
+#define	WF2_CRC           0x0000FFFF    /* Wake-Up Filter 2 Pattern CRC                           */
+#define	WF3_CRC           0xFFFF0000    /* Wake-Up Filter 3 Pattern CRC                           */
+
+#define	SET_WF2_CRC(x) (((x)&0xFFFF)<<   0 ) /* Set Wake-Up Filter 2 Target CRC                   */
+#define	SET_WF3_CRC(x) (((x)&0xFFFF)<<  16 ) /* Set Wake-Up Filter 3 Target CRC                   */
+
+/* EMAC_SYSCTL Masks */
+
+#define	PHYIE             0x00000001    /* PHY_INT Interrupt Enable                               */
+#define	RXDWA             0x00000002    /* Receive Frame DMA Word Alignment (Odd/Even*)           */
+#define	RXCKS             0x00000004    /* Enable RX Frame TCP/UDP Checksum Computation           */
+#define	TXDWA             0x00000010    /* Transmit Frame DMA Word Alignment (Odd/Even*)          */
+#define	MDCDIV            0x00003F00    /* SCLK:MDC Clock Divisor [MDC=SCLK/(2*(N+1))]            */
+
+#define	SET_MDCDIV(x) (((x)&0x3F)<< 8)   /* Set MDC Clock Divisor                                 */
+
+/* EMAC_SYSTAT Masks */
+
+#define	PHYINT            0x00000001    /* PHY_INT Interrupt Status                               */
+#define	MMCINT            0x00000002    /* MMC Counter Interrupt Status                           */
+#define	RXFSINT           0x00000004    /* RX Frame-Status Interrupt Status                       */
+#define	TXFSINT           0x00000008    /* TX Frame-Status Interrupt Status                       */
+#define	WAKEDET           0x00000010    /* Wake-Up Detected Status                                */
+#define	RXDMAERR          0x00000020    /* RX DMA Direction Error Status                          */
+#define	TXDMAERR          0x00000040    /* TX DMA Direction Error Status                          */
+#define	STMDONE           0x00000080    /* Station Mgt. Transfer Done Interrupt Status            */
+
+/* EMAC_RX_STAT, EMAC_RX_STKY, and EMAC_RX_IRQE Masks */
+
+#define	RX_FRLEN          0x000007FF    /* Frame Length In Bytes                                  */
+#define	RX_COMP           0x00001000    /* RX Frame Complete                                      */
+#define	RX_OK             0x00002000    /* RX Frame Received With No Errors                       */
+#define	RX_LONG           0x00004000    /* RX Frame Too Long Error                                */
+#define	RX_ALIGN          0x00008000    /* RX Frame Alignment Error                               */
+#define	RX_CRC            0x00010000    /* RX Frame CRC Error                                     */
+#define	RX_LEN            0x00020000    /* RX Frame Length Error                                  */
+#define	RX_FRAG           0x00040000    /* RX Frame Fragment Error                                */
+#define	RX_ADDR           0x00080000    /* RX Frame Address Filter Failed Error                   */
+#define	RX_DMAO           0x00100000    /* RX Frame DMA Overrun Error                             */
+#define	RX_PHY            0x00200000    /* RX Frame PHY Error                                     */
+#define	RX_LATE           0x00400000    /* RX Frame Late Collision Error                          */
+#define	RX_RANGE          0x00800000    /* RX Frame Length Field Out of Range Error               */
+#define	RX_MULTI          0x01000000    /* RX Multicast Frame Indicator                           */
+#define	RX_BROAD          0x02000000    /* RX Broadcast Frame Indicator                           */
+#define	RX_CTL            0x04000000    /* RX Control Frame Indicator                             */
+#define	RX_UCTL           0x08000000    /* Unsupported RX Control Frame Indicator                 */
+#define	RX_TYPE           0x10000000    /* RX Typed Frame Indicator                               */
+#define	RX_VLAN1          0x20000000    /* RX VLAN1 Frame Indicator                               */
+#define	RX_VLAN2          0x40000000    /* RX VLAN2 Frame Indicator                               */
+#define	RX_ACCEPT         0x80000000    /* RX Frame Accepted Indicator                            */
+
+/*  EMAC_TX_STAT, EMAC_TX_STKY, and EMAC_TX_IRQE Masks  */
+
+#define	TX_COMP           0x00000001    /* TX Frame Complete                                      */
+#define	TX_OK             0x00000002    /* TX Frame Sent With No Errors                           */
+#define	TX_ECOLL          0x00000004    /* TX Frame Excessive Collision Error                     */
+#define	TX_LATE           0x00000008    /* TX Frame Late Collision Error                          */
+#define	TX_DMAU           0x00000010    /* TX Frame DMA Underrun Error (STAT)                     */
+#define	TX_MACE           0x00000010    /* Internal MAC Error Detected (STKY and IRQE)            */
+#define	TX_EDEFER         0x00000020    /* TX Frame Excessive Deferral Error                      */
+#define	TX_BROAD          0x00000040    /* TX Broadcast Frame Indicator                           */
+#define	TX_MULTI          0x00000080    /* TX Multicast Frame Indicator                           */
+#define	TX_CCNT           0x00000F00    /* TX Frame Collision Count                               */
+#define	TX_DEFER          0x00001000    /* TX Frame Deferred Indicator                            */
+#define	TX_CRS            0x00002000    /* TX Frame Carrier Sense Not Asserted Error              */
+#define	TX_LOSS           0x00004000    /* TX Frame Carrier Lost During TX Error                  */
+#define	TX_RETRY          0x00008000    /* TX Frame Successful After Retry                        */
+#define	TX_FRLEN          0x07FF0000    /* TX Frame Length (Bytes)                                */
+
+/* EMAC_MMC_CTL Masks */
+#define	RSTC              0x00000001    /* Reset All Counters                                     */
+#define	CROLL             0x00000002    /* Counter Roll-Over Enable                               */
+#define	CCOR              0x00000004    /* Counter Clear-On-Read Mode Enable                      */
+#define	MMCE              0x00000008    /* Enable MMC Counter Operation                           */
+
+/* EMAC_MMC_RIRQS and EMAC_MMC_RIRQE Masks */
+#define	RX_OK_CNT         0x00000001    /* RX Frames Received With No Errors                      */
+#define	RX_FCS_CNT        0x00000002    /* RX Frames W/Frame Check Sequence Errors                */
+#define	RX_ALIGN_CNT      0x00000004    /* RX Frames With Alignment Errors                        */
+#define	RX_OCTET_CNT      0x00000008    /* RX Octets Received OK                                  */
+#define	RX_LOST_CNT       0x00000010    /* RX Frames Lost Due To Internal MAC RX Error            */
+#define	RX_UNI_CNT        0x00000020    /* Unicast RX Frames Received OK                          */
+#define	RX_MULTI_CNT      0x00000040    /* Multicast RX Frames Received OK                        */
+#define	RX_BROAD_CNT      0x00000080    /* Broadcast RX Frames Received OK                        */
+#define	RX_IRL_CNT        0x00000100    /* RX Frames With In-Range Length Errors                  */
+#define	RX_ORL_CNT        0x00000200    /* RX Frames With Out-Of-Range Length Errors              */
+#define	RX_LONG_CNT       0x00000400    /* RX Frames With Frame Too Long Errors                   */
+#define	RX_MACCTL_CNT     0x00000800    /* MAC Control RX Frames Received                         */
+#define	RX_OPCODE_CTL     0x00001000    /* Unsupported Op-Code RX Frames Received                 */
+#define	RX_PAUSE_CNT      0x00002000    /* PAUSEMAC Control RX Frames Received                    */
+#define	RX_ALLF_CNT       0x00004000    /* All RX Frames Received                                 */
+#define	RX_ALLO_CNT       0x00008000    /* All RX Octets Received                                 */
+#define	RX_TYPED_CNT      0x00010000    /* Typed RX Frames Received                               */
+#define	RX_SHORT_CNT      0x00020000    /* RX Frame Fragments (< 64 Bytes) Received               */
+#define	RX_EQ64_CNT       0x00040000    /* 64-Byte RX Frames Received                             */
+#define	RX_LT128_CNT      0x00080000    /* 65-127-Byte RX Frames Received                         */
+#define	RX_LT256_CNT      0x00100000    /* 128-255-Byte RX Frames Received                        */
+#define	RX_LT512_CNT      0x00200000    /* 256-511-Byte RX Frames Received                        */
+#define	RX_LT1024_CNT     0x00400000    /* 512-1023-Byte RX Frames Received                       */
+#define	RX_GE1024_CNT     0x00800000    /* 1024-Max-Byte RX Frames Received                       */
+
+/* EMAC_MMC_TIRQS and EMAC_MMC_TIRQE Masks  */
+
+#define	TX_OK_CNT         0x00000001    /* TX Frames Sent OK                                      */
+#define	TX_SCOLL_CNT      0x00000002    /* TX Frames With Single Collisions                       */
+#define	TX_MCOLL_CNT      0x00000004    /* TX Frames With Multiple Collisions                     */
+#define	TX_OCTET_CNT      0x00000008    /* TX Octets Sent OK                                      */
+#define	TX_DEFER_CNT      0x00000010    /* TX Frames With Deferred Transmission                   */
+#define	TX_LATE_CNT       0x00000020    /* TX Frames With Late Collisions                         */
+#define	TX_ABORTC_CNT     0x00000040    /* TX Frames Aborted Due To Excess Collisions             */
+#define	TX_LOST_CNT       0x00000080    /* TX Frames Lost Due To Internal MAC TX Error            */
+#define	TX_CRS_CNT        0x00000100    /* TX Frames With Carrier Sense Errors                    */
+#define	TX_UNI_CNT        0x00000200    /* Unicast TX Frames Sent                                 */
+#define	TX_MULTI_CNT      0x00000400    /* Multicast TX Frames Sent                               */
+#define	TX_BROAD_CNT      0x00000800    /* Broadcast TX Frames Sent                               */
+#define	TX_EXDEF_CTL      0x00001000    /* TX Frames With Excessive Deferral                      */
+#define	TX_MACCTL_CNT     0x00002000    /* MAC Control TX Frames Sent                             */
+#define	TX_ALLF_CNT       0x00004000    /* All TX Frames Sent                                     */
+#define	TX_ALLO_CNT       0x00008000    /* All TX Octets Sent                                     */
+#define	TX_EQ64_CNT       0x00010000    /* 64-Byte TX Frames Sent                                 */
+#define	TX_LT128_CNT      0x00020000    /* 65-127-Byte TX Frames Sent                             */
+#define	TX_LT256_CNT      0x00040000    /* 128-255-Byte TX Frames Sent                            */
+#define	TX_LT512_CNT      0x00080000    /* 256-511-Byte TX Frames Sent                            */
+#define	TX_LT1024_CNT     0x00100000    /* 512-1023-Byte TX Frames Sent                           */
+#define	TX_GE1024_CNT     0x00200000    /* 1024-Max-Byte TX Frames Sent                           */
+#define	TX_ABORT_CNT      0x00400000    /* TX Frames Aborted                                      */
+
+/* USB Control Registers */
+
+#define                        USB_FADDR  0xffc03800   /* Function address register */
+#define                        USB_POWER  0xffc03804   /* Power management register */
+#define                       USB_INTRTX  0xffc03808   /* Interrupt register for endpoint 0 and Tx endpoint 1 to 7 */
+#define                       USB_INTRRX  0xffc0380c   /* Interrupt register for Rx endpoints 1 to 7 */
+#define                      USB_INTRTXE  0xffc03810   /* Interrupt enable register for IntrTx */
+#define                      USB_INTRRXE  0xffc03814   /* Interrupt enable register for IntrRx */
+#define                      USB_INTRUSB  0xffc03818   /* Interrupt register for common USB interrupts */
+#define                     USB_INTRUSBE  0xffc0381c   /* Interrupt enable register for IntrUSB */
+#define                        USB_FRAME  0xffc03820   /* USB frame number */
+#define                        USB_INDEX  0xffc03824   /* Index register for selecting the indexed endpoint registers */
+#define                     USB_TESTMODE  0xffc03828   /* Enabled USB 20 test modes */
+#define                     USB_GLOBINTR  0xffc0382c   /* Global Interrupt Mask register and Wakeup Exception Interrupt */
+#define                   USB_GLOBAL_CTL  0xffc03830   /* Global Clock Control for the core */
+
+/* USB Packet Control Registers */
+
+#define                USB_TX_MAX_PACKET  0xffc03840   /* Maximum packet size for Host Tx endpoint */
+#define                         USB_CSR0  0xffc03844   /* Control Status register for endpoint 0 and Control Status register for Host Tx endpoint */
+#define                        USB_TXCSR  0xffc03844   /* Control Status register for endpoint 0 and Control Status register for Host Tx endpoint */
+#define                USB_RX_MAX_PACKET  0xffc03848   /* Maximum packet size for Host Rx endpoint */
+#define                        USB_RXCSR  0xffc0384c   /* Control Status register for Host Rx endpoint */
+#define                       USB_COUNT0  0xffc03850   /* Number of bytes received in endpoint 0 FIFO and Number of bytes received in Host Tx endpoint */
+#define                      USB_RXCOUNT  0xffc03850   /* Number of bytes received in endpoint 0 FIFO and Number of bytes received in Host Tx endpoint */
+#define                       USB_TXTYPE  0xffc03854   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint */
+#define                    USB_NAKLIMIT0  0xffc03858   /* Sets the NAK response timeout on Endpoint 0 and on Bulk transfers for Host Tx endpoint */
+#define                   USB_TXINTERVAL  0xffc03858   /* Sets the NAK response timeout on Endpoint 0 and on Bulk transfers for Host Tx endpoint */
+#define                       USB_RXTYPE  0xffc0385c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint */
+#define                   USB_RXINTERVAL  0xffc03860   /* Sets the polling interval for Interrupt and Isochronous transfers or the NAK response timeout on Bulk transfers */
+#define                      USB_TXCOUNT  0xffc03868   /* Number of bytes to be written to the selected endpoint Tx FIFO */
+
+/* USB Endpoint FIFO Registers */
+
+#define                     USB_EP0_FIFO  0xffc03880   /* Endpoint 0 FIFO */
+#define                     USB_EP1_FIFO  0xffc03888   /* Endpoint 1 FIFO */
+#define                     USB_EP2_FIFO  0xffc03890   /* Endpoint 2 FIFO */
+#define                     USB_EP3_FIFO  0xffc03898   /* Endpoint 3 FIFO */
+#define                     USB_EP4_FIFO  0xffc038a0   /* Endpoint 4 FIFO */
+#define                     USB_EP5_FIFO  0xffc038a8   /* Endpoint 5 FIFO */
+#define                     USB_EP6_FIFO  0xffc038b0   /* Endpoint 6 FIFO */
+#define                     USB_EP7_FIFO  0xffc038b8   /* Endpoint 7 FIFO */
+
+/* USB OTG Control Registers */
+
+#define                  USB_OTG_DEV_CTL  0xffc03900   /* OTG Device Control Register */
+#define                 USB_OTG_VBUS_IRQ  0xffc03904   /* OTG VBUS Control Interrupts */
+#define                USB_OTG_VBUS_MASK  0xffc03908   /* VBUS Control Interrupt Enable */
+
+/* USB Phy Control Registers */
+
+#define                     USB_LINKINFO  0xffc03948   /* Enables programming of some PHY-side delays */
+#define                        USB_VPLEN  0xffc0394c   /* Determines duration of VBUS pulse for VBUS charging */
+#define                      USB_HS_EOF1  0xffc03950   /* Time buffer for High-Speed transactions */
+#define                      USB_FS_EOF1  0xffc03954   /* Time buffer for Full-Speed transactions */
+#define                      USB_LS_EOF1  0xffc03958   /* Time buffer for Low-Speed transactions */
+
+/* (APHY_CNTRL is for ADI usage only) */
+
+#define                   USB_APHY_CNTRL  0xffc039e0   /* Register that increases visibility of Analog PHY */
+
+/* (APHY_CALIB is for ADI usage only) */
+
+#define                   USB_APHY_CALIB  0xffc039e4   /* Register used to set some calibration values */
+
+#define                  USB_APHY_CNTRL2  0xffc039e8   /* Register used to prevent re-enumeration once Moab goes into hibernate mode */
+
+/* (PHY_TEST is for ADI usage only) */
+
+#define                     USB_PHY_TEST  0xffc039ec   /* Used for reducing simulation time and simplifies FIFO testability */
+
+#define                  USB_PLLOSC_CTRL  0xffc039f0   /* Used to program different parameters for USB PLL and Oscillator */
+#define                   USB_SRP_CLKDIV  0xffc039f4   /* Used to program clock divide value for the clock fed to the SRP detection logic */
+
+/* USB Endpoint 0 Control Registers */
+
+#define                USB_EP_NI0_TXMAXP  0xffc03a00   /* Maximum packet size for Host Tx endpoint0 */
+#define                 USB_EP_NI0_TXCSR  0xffc03a04   /* Control Status register for endpoint 0 */
+#define                USB_EP_NI0_RXMAXP  0xffc03a08   /* Maximum packet size for Host Rx endpoint0 */
+#define                 USB_EP_NI0_RXCSR  0xffc03a0c   /* Control Status register for Host Rx endpoint0 */
+#define               USB_EP_NI0_RXCOUNT  0xffc03a10   /* Number of bytes received in endpoint 0 FIFO */
+#define                USB_EP_NI0_TXTYPE  0xffc03a14   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint0 */
+#define            USB_EP_NI0_TXINTERVAL  0xffc03a18   /* Sets the NAK response timeout on Endpoint 0 */
+#define                USB_EP_NI0_RXTYPE  0xffc03a1c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint0 */
+#define            USB_EP_NI0_RXINTERVAL  0xffc03a20   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint0 */
+#define               USB_EP_NI0_TXCOUNT  0xffc03a28   /* Number of bytes to be written to the endpoint0 Tx FIFO */
+
+/* USB Endpoint 1 Control Registers */
+
+#define                USB_EP_NI1_TXMAXP  0xffc03a40   /* Maximum packet size for Host Tx endpoint1 */
+#define                 USB_EP_NI1_TXCSR  0xffc03a44   /* Control Status register for endpoint1 */
+#define                USB_EP_NI1_RXMAXP  0xffc03a48   /* Maximum packet size for Host Rx endpoint1 */
+#define                 USB_EP_NI1_RXCSR  0xffc03a4c   /* Control Status register for Host Rx endpoint1 */
+#define               USB_EP_NI1_RXCOUNT  0xffc03a50   /* Number of bytes received in endpoint1 FIFO */
+#define                USB_EP_NI1_TXTYPE  0xffc03a54   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint1 */
+#define            USB_EP_NI1_TXINTERVAL  0xffc03a58   /* Sets the NAK response timeout on Endpoint1 */
+#define                USB_EP_NI1_RXTYPE  0xffc03a5c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint1 */
+#define            USB_EP_NI1_RXINTERVAL  0xffc03a60   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint1 */
+#define               USB_EP_NI1_TXCOUNT  0xffc03a68   /* Number of bytes to be written to the+H102 endpoint1 Tx FIFO */
+
+/* USB Endpoint 2 Control Registers */
+
+#define                USB_EP_NI2_TXMAXP  0xffc03a80   /* Maximum packet size for Host Tx endpoint2 */
+#define                 USB_EP_NI2_TXCSR  0xffc03a84   /* Control Status register for endpoint2 */
+#define                USB_EP_NI2_RXMAXP  0xffc03a88   /* Maximum packet size for Host Rx endpoint2 */
+#define                 USB_EP_NI2_RXCSR  0xffc03a8c   /* Control Status register for Host Rx endpoint2 */
+#define               USB_EP_NI2_RXCOUNT  0xffc03a90   /* Number of bytes received in endpoint2 FIFO */
+#define                USB_EP_NI2_TXTYPE  0xffc03a94   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint2 */
+#define            USB_EP_NI2_TXINTERVAL  0xffc03a98   /* Sets the NAK response timeout on Endpoint2 */
+#define                USB_EP_NI2_RXTYPE  0xffc03a9c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint2 */
+#define            USB_EP_NI2_RXINTERVAL  0xffc03aa0   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint2 */
+#define               USB_EP_NI2_TXCOUNT  0xffc03aa8   /* Number of bytes to be written to the endpoint2 Tx FIFO */
+
+/* USB Endpoint 3 Control Registers */
+
+#define                USB_EP_NI3_TXMAXP  0xffc03ac0   /* Maximum packet size for Host Tx endpoint3 */
+#define                 USB_EP_NI3_TXCSR  0xffc03ac4   /* Control Status register for endpoint3 */
+#define                USB_EP_NI3_RXMAXP  0xffc03ac8   /* Maximum packet size for Host Rx endpoint3 */
+#define                 USB_EP_NI3_RXCSR  0xffc03acc   /* Control Status register for Host Rx endpoint3 */
+#define               USB_EP_NI3_RXCOUNT  0xffc03ad0   /* Number of bytes received in endpoint3 FIFO */
+#define                USB_EP_NI3_TXTYPE  0xffc03ad4   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint3 */
+#define            USB_EP_NI3_TXINTERVAL  0xffc03ad8   /* Sets the NAK response timeout on Endpoint3 */
+#define                USB_EP_NI3_RXTYPE  0xffc03adc   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint3 */
+#define            USB_EP_NI3_RXINTERVAL  0xffc03ae0   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint3 */
+#define               USB_EP_NI3_TXCOUNT  0xffc03ae8   /* Number of bytes to be written to the H124endpoint3 Tx FIFO */
+
+/* USB Endpoint 4 Control Registers */
+
+#define                USB_EP_NI4_TXMAXP  0xffc03b00   /* Maximum packet size for Host Tx endpoint4 */
+#define                 USB_EP_NI4_TXCSR  0xffc03b04   /* Control Status register for endpoint4 */
+#define                USB_EP_NI4_RXMAXP  0xffc03b08   /* Maximum packet size for Host Rx endpoint4 */
+#define                 USB_EP_NI4_RXCSR  0xffc03b0c   /* Control Status register for Host Rx endpoint4 */
+#define               USB_EP_NI4_RXCOUNT  0xffc03b10   /* Number of bytes received in endpoint4 FIFO */
+#define                USB_EP_NI4_TXTYPE  0xffc03b14   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint4 */
+#define            USB_EP_NI4_TXINTERVAL  0xffc03b18   /* Sets the NAK response timeout on Endpoint4 */
+#define                USB_EP_NI4_RXTYPE  0xffc03b1c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint4 */
+#define            USB_EP_NI4_RXINTERVAL  0xffc03b20   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint4 */
+#define               USB_EP_NI4_TXCOUNT  0xffc03b28   /* Number of bytes to be written to the endpoint4 Tx FIFO */
+
+/* USB Endpoint 5 Control Registers */
+
+#define                USB_EP_NI5_TXMAXP  0xffc03b40   /* Maximum packet size for Host Tx endpoint5 */
+#define                 USB_EP_NI5_TXCSR  0xffc03b44   /* Control Status register for endpoint5 */
+#define                USB_EP_NI5_RXMAXP  0xffc03b48   /* Maximum packet size for Host Rx endpoint5 */
+#define                 USB_EP_NI5_RXCSR  0xffc03b4c   /* Control Status register for Host Rx endpoint5 */
+#define               USB_EP_NI5_RXCOUNT  0xffc03b50   /* Number of bytes received in endpoint5 FIFO */
+#define                USB_EP_NI5_TXTYPE  0xffc03b54   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint5 */
+#define            USB_EP_NI5_TXINTERVAL  0xffc03b58   /* Sets the NAK response timeout on Endpoint5 */
+#define                USB_EP_NI5_RXTYPE  0xffc03b5c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint5 */
+#define            USB_EP_NI5_RXINTERVAL  0xffc03b60   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint5 */
+#define               USB_EP_NI5_TXCOUNT  0xffc03b68   /* Number of bytes to be written to the endpoint5 Tx FIFO */
+
+/* USB Endpoint 6 Control Registers */
+
+#define                USB_EP_NI6_TXMAXP  0xffc03b80   /* Maximum packet size for Host Tx endpoint6 */
+#define                 USB_EP_NI6_TXCSR  0xffc03b84   /* Control Status register for endpoint6 */
+#define                USB_EP_NI6_RXMAXP  0xffc03b88   /* Maximum packet size for Host Rx endpoint6 */
+#define                 USB_EP_NI6_RXCSR  0xffc03b8c   /* Control Status register for Host Rx endpoint6 */
+#define               USB_EP_NI6_RXCOUNT  0xffc03b90   /* Number of bytes received in endpoint6 FIFO */
+#define                USB_EP_NI6_TXTYPE  0xffc03b94   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint6 */
+#define            USB_EP_NI6_TXINTERVAL  0xffc03b98   /* Sets the NAK response timeout on Endpoint6 */
+#define                USB_EP_NI6_RXTYPE  0xffc03b9c   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint6 */
+#define            USB_EP_NI6_RXINTERVAL  0xffc03ba0   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint6 */
+#define               USB_EP_NI6_TXCOUNT  0xffc03ba8   /* Number of bytes to be written to the endpoint6 Tx FIFO */
+
+/* USB Endpoint 7 Control Registers */
+
+#define                USB_EP_NI7_TXMAXP  0xffc03bc0   /* Maximum packet size for Host Tx endpoint7 */
+#define                 USB_EP_NI7_TXCSR  0xffc03bc4   /* Control Status register for endpoint7 */
+#define                USB_EP_NI7_RXMAXP  0xffc03bc8   /* Maximum packet size for Host Rx endpoint7 */
+#define                 USB_EP_NI7_RXCSR  0xffc03bcc   /* Control Status register for Host Rx endpoint7 */
+#define               USB_EP_NI7_RXCOUNT  0xffc03bd0   /* Number of bytes received in endpoint7 FIFO */
+#define                USB_EP_NI7_TXTYPE  0xffc03bd4   /* Sets the transaction protocol and peripheral endpoint number for the Host Tx endpoint7 */
+#define            USB_EP_NI7_TXINTERVAL  0xffc03bd8   /* Sets the NAK response timeout on Endpoint7 */
+#define                USB_EP_NI7_RXTYPE  0xffc03bdc   /* Sets the transaction protocol and peripheral endpoint number for the Host Rx endpoint7 */
+#define            USB_EP_NI7_RXINTERVAL  0xffc03bf0   /* Sets the polling interval for Interrupt/Isochronous transfers or the NAK response timeout on Bulk transfers for Host Rx endpoint7 */
+#define               USB_EP_NI7_TXCOUNT  0xffc03bf8   /* Number of bytes to be written to the endpoint7 Tx FIFO */
+
+#define                USB_DMA_INTERRUPT  0xffc03c00   /* Indicates pending interrupts for the DMA channels */
+
+/* USB Channel 0 Config Registers */
+
+#define                  USB_DMA0CONTROL  0xffc03c04   /* DMA master channel 0 configuration */
+#define                  USB_DMA0ADDRLOW  0xffc03c08   /* Lower 16-bits of memory source/destination address for DMA master channel 0 */
+#define                 USB_DMA0ADDRHIGH  0xffc03c0c   /* Upper 16-bits of memory source/destination address for DMA master channel 0 */
+#define                 USB_DMA0COUNTLOW  0xffc03c10   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 0 */
+#define                USB_DMA0COUNTHIGH  0xffc03c14   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 0 */
+
+/* USB Channel 1 Config Registers */
+
+#define                  USB_DMA1CONTROL  0xffc03c24   /* DMA master channel 1 configuration */
+#define                  USB_DMA1ADDRLOW  0xffc03c28   /* Lower 16-bits of memory source/destination address for DMA master channel 1 */
+#define                 USB_DMA1ADDRHIGH  0xffc03c2c   /* Upper 16-bits of memory source/destination address for DMA master channel 1 */
+#define                 USB_DMA1COUNTLOW  0xffc03c30   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 1 */
+#define                USB_DMA1COUNTHIGH  0xffc03c34   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 1 */
+
+/* USB Channel 2 Config Registers */
+
+#define                  USB_DMA2CONTROL  0xffc03c44   /* DMA master channel 2 configuration */
+#define                  USB_DMA2ADDRLOW  0xffc03c48   /* Lower 16-bits of memory source/destination address for DMA master channel 2 */
+#define                 USB_DMA2ADDRHIGH  0xffc03c4c   /* Upper 16-bits of memory source/destination address for DMA master channel 2 */
+#define                 USB_DMA2COUNTLOW  0xffc03c50   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 2 */
+#define                USB_DMA2COUNTHIGH  0xffc03c54   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 2 */
+
+/* USB Channel 3 Config Registers */
+
+#define                  USB_DMA3CONTROL  0xffc03c64   /* DMA master channel 3 configuration */
+#define                  USB_DMA3ADDRLOW  0xffc03c68   /* Lower 16-bits of memory source/destination address for DMA master channel 3 */
+#define                 USB_DMA3ADDRHIGH  0xffc03c6c   /* Upper 16-bits of memory source/destination address for DMA master channel 3 */
+#define                 USB_DMA3COUNTLOW  0xffc03c70   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 3 */
+#define                USB_DMA3COUNTHIGH  0xffc03c74   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 3 */
+
+/* USB Channel 4 Config Registers */
+
+#define                  USB_DMA4CONTROL  0xffc03c84   /* DMA master channel 4 configuration */
+#define                  USB_DMA4ADDRLOW  0xffc03c88   /* Lower 16-bits of memory source/destination address for DMA master channel 4 */
+#define                 USB_DMA4ADDRHIGH  0xffc03c8c   /* Upper 16-bits of memory source/destination address for DMA master channel 4 */
+#define                 USB_DMA4COUNTLOW  0xffc03c90   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 4 */
+#define                USB_DMA4COUNTHIGH  0xffc03c94   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 4 */
+
+/* USB Channel 5 Config Registers */
+
+#define                  USB_DMA5CONTROL  0xffc03ca4   /* DMA master channel 5 configuration */
+#define                  USB_DMA5ADDRLOW  0xffc03ca8   /* Lower 16-bits of memory source/destination address for DMA master channel 5 */
+#define                 USB_DMA5ADDRHIGH  0xffc03cac   /* Upper 16-bits of memory source/destination address for DMA master channel 5 */
+#define                 USB_DMA5COUNTLOW  0xffc03cb0   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 5 */
+#define                USB_DMA5COUNTHIGH  0xffc03cb4   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 5 */
+
+/* USB Channel 6 Config Registers */
+
+#define                  USB_DMA6CONTROL  0xffc03cc4   /* DMA master channel 6 configuration */
+#define                  USB_DMA6ADDRLOW  0xffc03cc8   /* Lower 16-bits of memory source/destination address for DMA master channel 6 */
+#define                 USB_DMA6ADDRHIGH  0xffc03ccc   /* Upper 16-bits of memory source/destination address for DMA master channel 6 */
+#define                 USB_DMA6COUNTLOW  0xffc03cd0   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 6 */
+#define                USB_DMA6COUNTHIGH  0xffc03cd4   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 6 */
+
+/* USB Channel 7 Config Registers */
+
+#define                  USB_DMA7CONTROL  0xffc03ce4   /* DMA master channel 7 configuration */
+#define                  USB_DMA7ADDRLOW  0xffc03ce8   /* Lower 16-bits of memory source/destination address for DMA master channel 7 */
+#define                 USB_DMA7ADDRHIGH  0xffc03cec   /* Upper 16-bits of memory source/destination address for DMA master channel 7 */
+#define                 USB_DMA7COUNTLOW  0xffc03cf0   /* Lower 16-bits of byte count of DMA transfer for DMA master channel 7 */
+#define                USB_DMA7COUNTHIGH  0xffc03cf4   /* Upper 16-bits of byte count of DMA transfer for DMA master channel 7 */
+
+/* Bit masks for USB_FADDR */
+
+#define          FUNCTION_ADDRESS  0x7f       /* Function address */
+
+/* Bit masks for USB_POWER */
+
+#define           ENABLE_SUSPENDM  0x1        /* enable SuspendM output */
+#define          nENABLE_SUSPENDM  0x0       
+#define              SUSPEND_MODE  0x2        /* Suspend Mode indicator */
+#define             nSUSPEND_MODE  0x0       
+#define               RESUME_MODE  0x4        /* DMA Mode */
+#define              nRESUME_MODE  0x0       
+#define                     RESET  0x8        /* Reset indicator */
+#define                    nRESET  0x0       
+#define                   HS_MODE  0x10       /* High Speed mode indicator */
+#define                  nHS_MODE  0x0       
+#define                 HS_ENABLE  0x20       /* high Speed Enable */
+#define                nHS_ENABLE  0x0       
+#define                 SOFT_CONN  0x40       /* Soft connect */
+#define                nSOFT_CONN  0x0       
+#define                ISO_UPDATE  0x80       /* Isochronous update */
+#define               nISO_UPDATE  0x0       
+
+/* Bit masks for USB_INTRTX */
+
+#define                    EP0_TX  0x1        /* Tx Endpoint 0 interrupt */
+#define                   nEP0_TX  0x0       
+#define                    EP1_TX  0x2        /* Tx Endpoint 1 interrupt */
+#define                   nEP1_TX  0x0       
+#define                    EP2_TX  0x4        /* Tx Endpoint 2 interrupt */
+#define                   nEP2_TX  0x0       
+#define                    EP3_TX  0x8        /* Tx Endpoint 3 interrupt */
+#define                   nEP3_TX  0x0       
+#define                    EP4_TX  0x10       /* Tx Endpoint 4 interrupt */
+#define                   nEP4_TX  0x0       
+#define                    EP5_TX  0x20       /* Tx Endpoint 5 interrupt */
+#define                   nEP5_TX  0x0       
+#define                    EP6_TX  0x40       /* Tx Endpoint 6 interrupt */
+#define                   nEP6_TX  0x0       
+#define                    EP7_TX  0x80       /* Tx Endpoint 7 interrupt */
+#define                   nEP7_TX  0x0       
+
+/* Bit masks for USB_INTRRX */
+
+#define                    EP1_RX  0x2        /* Rx Endpoint 1 interrupt */
+#define                   nEP1_RX  0x0       
+#define                    EP2_RX  0x4        /* Rx Endpoint 2 interrupt */
+#define                   nEP2_RX  0x0       
+#define                    EP3_RX  0x8        /* Rx Endpoint 3 interrupt */
+#define                   nEP3_RX  0x0       
+#define                    EP4_RX  0x10       /* Rx Endpoint 4 interrupt */
+#define                   nEP4_RX  0x0       
+#define                    EP5_RX  0x20       /* Rx Endpoint 5 interrupt */
+#define                   nEP5_RX  0x0       
+#define                    EP6_RX  0x40       /* Rx Endpoint 6 interrupt */
+#define                   nEP6_RX  0x0       
+#define                    EP7_RX  0x80       /* Rx Endpoint 7 interrupt */
+#define                   nEP7_RX  0x0       
+
+/* Bit masks for USB_INTRTXE */
+
+#define                  EP0_TX_E  0x1        /* Endpoint 0 interrupt Enable */
+#define                 nEP0_TX_E  0x0       
+#define                  EP1_TX_E  0x2        /* Tx Endpoint 1 interrupt  Enable */
+#define                 nEP1_TX_E  0x0       
+#define                  EP2_TX_E  0x4        /* Tx Endpoint 2 interrupt  Enable */
+#define                 nEP2_TX_E  0x0       
+#define                  EP3_TX_E  0x8        /* Tx Endpoint 3 interrupt  Enable */
+#define                 nEP3_TX_E  0x0       
+#define                  EP4_TX_E  0x10       /* Tx Endpoint 4 interrupt  Enable */
+#define                 nEP4_TX_E  0x0       
+#define                  EP5_TX_E  0x20       /* Tx Endpoint 5 interrupt  Enable */
+#define                 nEP5_TX_E  0x0       
+#define                  EP6_TX_E  0x40       /* Tx Endpoint 6 interrupt  Enable */
+#define                 nEP6_TX_E  0x0       
+#define                  EP7_TX_E  0x80       /* Tx Endpoint 7 interrupt  Enable */
+#define                 nEP7_TX_E  0x0       
+
+/* Bit masks for USB_INTRRXE */
+
+#define                  EP1_RX_E  0x2        /* Rx Endpoint 1 interrupt  Enable */
+#define                 nEP1_RX_E  0x0       
+#define                  EP2_RX_E  0x4        /* Rx Endpoint 2 interrupt  Enable */
+#define                 nEP2_RX_E  0x0       
+#define                  EP3_RX_E  0x8        /* Rx Endpoint 3 interrupt  Enable */
+#define                 nEP3_RX_E  0x0       
+#define                  EP4_RX_E  0x10       /* Rx Endpoint 4 interrupt  Enable */
+#define                 nEP4_RX_E  0x0       
+#define                  EP5_RX_E  0x20       /* Rx Endpoint 5 interrupt  Enable */
+#define                 nEP5_RX_E  0x0       
+#define                  EP6_RX_E  0x40       /* Rx Endpoint 6 interrupt  Enable */
+#define                 nEP6_RX_E  0x0       
+#define                  EP7_RX_E  0x80       /* Rx Endpoint 7 interrupt  Enable */
+#define                 nEP7_RX_E  0x0       
+
+/* Bit masks for USB_INTRUSB */
+
+#define                 SUSPEND_B  0x1        /* Suspend indicator */
+#define                nSUSPEND_B  0x0       
+#define                  RESUME_B  0x2        /* Resume indicator */
+#define                 nRESUME_B  0x0       
+#define          RESET_OR_BABLE_B  0x4        /* Reset/babble indicator */
+#define         nRESET_OR_BABLE_B  0x0       
+#define                     SOF_B  0x8        /* Start of frame */
+#define                    nSOF_B  0x0       
+#define                    CONN_B  0x10       /* Connection indicator */
+#define                   nCONN_B  0x0       
+#define                  DISCON_B  0x20       /* Disconnect indicator */
+#define                 nDISCON_B  0x0       
+#define             SESSION_REQ_B  0x40       /* Session Request */
+#define            nSESSION_REQ_B  0x0       
+#define              VBUS_ERROR_B  0x80       /* Vbus threshold indicator */
+#define             nVBUS_ERROR_B  0x0       
+
+/* Bit masks for USB_INTRUSBE */
+
+#define                SUSPEND_BE  0x1        /* Suspend indicator int enable */
+#define               nSUSPEND_BE  0x0       
+#define                 RESUME_BE  0x2        /* Resume indicator int enable */
+#define                nRESUME_BE  0x0       
+#define         RESET_OR_BABLE_BE  0x4        /* Reset/babble indicator int enable */
+#define        nRESET_OR_BABLE_BE  0x0       
+#define                    SOF_BE  0x8        /* Start of frame int enable */
+#define                   nSOF_BE  0x0       
+#define                   CONN_BE  0x10       /* Connection indicator int enable */
+#define                  nCONN_BE  0x0       
+#define                 DISCON_BE  0x20       /* Disconnect indicator int enable */
+#define                nDISCON_BE  0x0       
+#define            SESSION_REQ_BE  0x40       /* Session Request int enable */
+#define           nSESSION_REQ_BE  0x0       
+#define             VBUS_ERROR_BE  0x80       /* Vbus threshold indicator int enable */
+#define            nVBUS_ERROR_BE  0x0       
+
+/* Bit masks for USB_FRAME */
+
+#define              FRAME_NUMBER  0x7ff      /* Frame number */
+
+/* Bit masks for USB_INDEX */
+
+#define         SELECTED_ENDPOINT  0xf        /* selected endpoint */
+
+/* Bit masks for USB_GLOBAL_CTL */
+
+#define                GLOBAL_ENA  0x1        /* enables USB module */
+#define               nGLOBAL_ENA  0x0       
+#define                EP1_TX_ENA  0x2        /* Transmit endpoint 1 enable */
+#define               nEP1_TX_ENA  0x0       
+#define                EP2_TX_ENA  0x4        /* Transmit endpoint 2 enable */
+#define               nEP2_TX_ENA  0x0       
+#define                EP3_TX_ENA  0x8        /* Transmit endpoint 3 enable */
+#define               nEP3_TX_ENA  0x0       
+#define                EP4_TX_ENA  0x10       /* Transmit endpoint 4 enable */
+#define               nEP4_TX_ENA  0x0       
+#define                EP5_TX_ENA  0x20       /* Transmit endpoint 5 enable */
+#define               nEP5_TX_ENA  0x0       
+#define                EP6_TX_ENA  0x40       /* Transmit endpoint 6 enable */
+#define               nEP6_TX_ENA  0x0       
+#define                EP7_TX_ENA  0x80       /* Transmit endpoint 7 enable */
+#define               nEP7_TX_ENA  0x0       
+#define                EP1_RX_ENA  0x100      /* Receive endpoint 1 enable */
+#define               nEP1_RX_ENA  0x0       
+#define                EP2_RX_ENA  0x200      /* Receive endpoint 2 enable */
+#define               nEP2_RX_ENA  0x0       
+#define                EP3_RX_ENA  0x400      /* Receive endpoint 3 enable */
+#define               nEP3_RX_ENA  0x0       
+#define                EP4_RX_ENA  0x800      /* Receive endpoint 4 enable */
+#define               nEP4_RX_ENA  0x0       
+#define                EP5_RX_ENA  0x1000     /* Receive endpoint 5 enable */
+#define               nEP5_RX_ENA  0x0       
+#define                EP6_RX_ENA  0x2000     /* Receive endpoint 6 enable */
+#define               nEP6_RX_ENA  0x0       
+#define                EP7_RX_ENA  0x4000     /* Receive endpoint 7 enable */
+#define               nEP7_RX_ENA  0x0       
+
+/* Bit masks for USB_OTG_DEV_CTL */
+
+#define                   SESSION  0x1        /* session indicator */
+#define                  nSESSION  0x0       
+#define                  HOST_REQ  0x2        /* Host negotiation request */
+#define                 nHOST_REQ  0x0       
+#define                 HOST_MODE  0x4        /* indicates USBDRC is a host */
+#define                nHOST_MODE  0x0       
+#define                     VBUS0  0x8        /* Vbus level indicator[0] */
+#define                    nVBUS0  0x0       
+#define                     VBUS1  0x10       /* Vbus level indicator[1] */
+#define                    nVBUS1  0x0       
+#define                     LSDEV  0x20       /* Low-speed indicator */
+#define                    nLSDEV  0x0       
+#define                     FSDEV  0x40       /* Full or High-speed indicator */
+#define                    nFSDEV  0x0       
+#define                  B_DEVICE  0x80       /* A' or 'B' device indicator */
+#define                 nB_DEVICE  0x0       
+
+/* Bit masks for USB_OTG_VBUS_IRQ */
+
+#define             DRIVE_VBUS_ON  0x1        /* indicator to drive VBUS control circuit */
+#define            nDRIVE_VBUS_ON  0x0       
+#define            DRIVE_VBUS_OFF  0x2        /* indicator to shut off charge pump */
+#define           nDRIVE_VBUS_OFF  0x0       
+#define           CHRG_VBUS_START  0x4        /* indicator for external circuit to start charging VBUS */
+#define          nCHRG_VBUS_START  0x0       
+#define             CHRG_VBUS_END  0x8        /* indicator for external circuit to end charging VBUS */
+#define            nCHRG_VBUS_END  0x0       
+#define        DISCHRG_VBUS_START  0x10       /* indicator to start discharging VBUS */
+#define       nDISCHRG_VBUS_START  0x0       
+#define          DISCHRG_VBUS_END  0x20       /* indicator to stop discharging VBUS */
+#define         nDISCHRG_VBUS_END  0x0       
+
+/* Bit masks for USB_OTG_VBUS_MASK */
+
+#define         DRIVE_VBUS_ON_ENA  0x1        /* enable DRIVE_VBUS_ON interrupt */
+#define        nDRIVE_VBUS_ON_ENA  0x0       
+#define        DRIVE_VBUS_OFF_ENA  0x2        /* enable DRIVE_VBUS_OFF interrupt */
+#define       nDRIVE_VBUS_OFF_ENA  0x0       
+#define       CHRG_VBUS_START_ENA  0x4        /* enable CHRG_VBUS_START interrupt */
+#define      nCHRG_VBUS_START_ENA  0x0       
+#define         CHRG_VBUS_END_ENA  0x8        /* enable CHRG_VBUS_END interrupt */
+#define        nCHRG_VBUS_END_ENA  0x0       
+#define    DISCHRG_VBUS_START_ENA  0x10       /* enable DISCHRG_VBUS_START interrupt */
+#define   nDISCHRG_VBUS_START_ENA  0x0       
+#define      DISCHRG_VBUS_END_ENA  0x20       /* enable DISCHRG_VBUS_END interrupt */
+#define     nDISCHRG_VBUS_END_ENA  0x0       
+
+/* Bit masks for USB_CSR0 */
+
+#define                  RXPKTRDY  0x1        /* data packet receive indicator */
+#define                 nRXPKTRDY  0x0       
+#define                  TXPKTRDY  0x2        /* data packet in FIFO indicator */
+#define                 nTXPKTRDY  0x0       
+#define                STALL_SENT  0x4        /* STALL handshake sent */
+#define               nSTALL_SENT  0x0       
+#define                   DATAEND  0x8        /* Data end indicator */
+#define                  nDATAEND  0x0       
+#define                  SETUPEND  0x10       /* Setup end */
+#define                 nSETUPEND  0x0       
+#define                 SENDSTALL  0x20       /* Send STALL handshake */
+#define                nSENDSTALL  0x0       
+#define         SERVICED_RXPKTRDY  0x40       /* used to clear the RxPktRdy bit */
+#define        nSERVICED_RXPKTRDY  0x0       
+#define         SERVICED_SETUPEND  0x80       /* used to clear the SetupEnd bit */
+#define        nSERVICED_SETUPEND  0x0       
+#define                 FLUSHFIFO  0x100      /* flush endpoint FIFO */
+#define                nFLUSHFIFO  0x0       
+#define          STALL_RECEIVED_H  0x4        /* STALL handshake received host mode */
+#define         nSTALL_RECEIVED_H  0x0       
+#define                SETUPPKT_H  0x8        /* send Setup token host mode */
+#define               nSETUPPKT_H  0x0       
+#define                   ERROR_H  0x10       /* timeout error indicator host mode */
+#define                  nERROR_H  0x0       
+#define                  REQPKT_H  0x20       /* Request an IN transaction host mode */
+#define                 nREQPKT_H  0x0       
+#define               STATUSPKT_H  0x40       /* Status stage transaction host mode */
+#define              nSTATUSPKT_H  0x0       
+#define             NAK_TIMEOUT_H  0x80       /* EP0 halted after a NAK host mode */
+#define            nNAK_TIMEOUT_H  0x0       
+
+/* Bit masks for USB_COUNT0 */
+
+#define              EP0_RX_COUNT  0x7f       /* number of received bytes in EP0 FIFO */
+
+/* Bit masks for USB_NAKLIMIT0 */
+
+#define             EP0_NAK_LIMIT  0x1f       /* number of frames/micro frames after which EP0 timeouts */
+
+/* Bit masks for USB_TX_MAX_PACKET */
+
+#define         MAX_PACKET_SIZE_T  0x7ff      /* maximum data pay load in a frame */
+
+/* Bit masks for USB_RX_MAX_PACKET */
+
+#define         MAX_PACKET_SIZE_R  0x7ff      /* maximum data pay load in a frame */
+
+/* Bit masks for USB_TXCSR */
+
+#define                TXPKTRDY_T  0x1        /* data packet in FIFO indicator */
+#define               nTXPKTRDY_T  0x0       
+#define          FIFO_NOT_EMPTY_T  0x2        /* FIFO not empty */
+#define         nFIFO_NOT_EMPTY_T  0x0       
+#define                UNDERRUN_T  0x4        /* TxPktRdy not set  for an IN token */
+#define               nUNDERRUN_T  0x0       
+#define               FLUSHFIFO_T  0x8        /* flush endpoint FIFO */
+#define              nFLUSHFIFO_T  0x0       
+#define              STALL_SEND_T  0x10       /* issue a Stall handshake */
+#define             nSTALL_SEND_T  0x0       
+#define              STALL_SENT_T  0x20       /* Stall handshake transmitted */
+#define             nSTALL_SENT_T  0x0       
+#define        CLEAR_DATATOGGLE_T  0x40       /* clear endpoint data toggle */
+#define       nCLEAR_DATATOGGLE_T  0x0       
+#define                INCOMPTX_T  0x80       /* indicates that a large packet is split */
+#define               nINCOMPTX_T  0x0       
+#define              DMAREQMODE_T  0x400      /* DMA mode (0 or 1) selection */
+#define             nDMAREQMODE_T  0x0       
+#define        FORCE_DATATOGGLE_T  0x800      /* Force data toggle */
+#define       nFORCE_DATATOGGLE_T  0x0       
+#define              DMAREQ_ENA_T  0x1000     /* Enable DMA request for Tx EP */
+#define             nDMAREQ_ENA_T  0x0       
+#define                     ISO_T  0x4000     /* enable Isochronous transfers */
+#define                    nISO_T  0x0       
+#define                 AUTOSET_T  0x8000     /* allows TxPktRdy to be set automatically */
+#define                nAUTOSET_T  0x0       
+#define                  ERROR_TH  0x4        /* error condition host mode */
+#define                 nERROR_TH  0x0       
+#define         STALL_RECEIVED_TH  0x20       /* Stall handshake received host mode */
+#define        nSTALL_RECEIVED_TH  0x0       
+#define            NAK_TIMEOUT_TH  0x80       /* NAK timeout host mode */
+#define           nNAK_TIMEOUT_TH  0x0       
+
+/* Bit masks for USB_TXCOUNT */
+
+#define                  TX_COUNT  0x1fff     /* Number of bytes to be written to the selected endpoint Tx FIFO */
+
+/* Bit masks for USB_RXCSR */
+
+#define                RXPKTRDY_R  0x1        /* data packet in FIFO indicator */
+#define               nRXPKTRDY_R  0x0       
+#define               FIFO_FULL_R  0x2        /* FIFO not empty */
+#define              nFIFO_FULL_R  0x0       
+#define                 OVERRUN_R  0x4        /* TxPktRdy not set  for an IN token */
+#define                nOVERRUN_R  0x0       
+#define               DATAERROR_R  0x8        /* Out packet cannot be loaded into Rx  FIFO */
+#define              nDATAERROR_R  0x0       
+#define               FLUSHFIFO_R  0x10       /* flush endpoint FIFO */
+#define              nFLUSHFIFO_R  0x0       
+#define              STALL_SEND_R  0x20       /* issue a Stall handshake */
+#define             nSTALL_SEND_R  0x0       
+#define              STALL_SENT_R  0x40       /* Stall handshake transmitted */
+#define             nSTALL_SENT_R  0x0       
+#define        CLEAR_DATATOGGLE_R  0x80       /* clear endpoint data toggle */
+#define       nCLEAR_DATATOGGLE_R  0x0       
+#define                INCOMPRX_R  0x100      /* indicates that a large packet is split */
+#define               nINCOMPRX_R  0x0       
+#define              DMAREQMODE_R  0x800      /* DMA mode (0 or 1) selection */
+#define             nDMAREQMODE_R  0x0       
+#define                 DISNYET_R  0x1000     /* disable Nyet handshakes */
+#define                nDISNYET_R  0x0       
+#define              DMAREQ_ENA_R  0x2000     /* Enable DMA request for Tx EP */
+#define             nDMAREQ_ENA_R  0x0       
+#define                     ISO_R  0x4000     /* enable Isochronous transfers */
+#define                    nISO_R  0x0       
+#define               AUTOCLEAR_R  0x8000     /* allows TxPktRdy to be set automatically */
+#define              nAUTOCLEAR_R  0x0       
+#define                  ERROR_RH  0x4        /* TxPktRdy not set  for an IN token host mode */
+#define                 nERROR_RH  0x0       
+#define                 REQPKT_RH  0x20       /* request an IN transaction host mode */
+#define                nREQPKT_RH  0x0       
+#define         STALL_RECEIVED_RH  0x40       /* Stall handshake received host mode */
+#define        nSTALL_RECEIVED_RH  0x0       
+#define               INCOMPRX_RH  0x100      /* indicates that a large packet is split host mode */
+#define              nINCOMPRX_RH  0x0       
+#define             DMAREQMODE_RH  0x800      /* DMA mode (0 or 1) selection host mode */
+#define            nDMAREQMODE_RH  0x0       
+#define                AUTOREQ_RH  0x4000     /* sets ReqPkt automatically host mode */
+#define               nAUTOREQ_RH  0x0       
+
+/* Bit masks for USB_RXCOUNT */
+
+#define                  RX_COUNT  0x1fff     /* Number of received bytes in the packet in the Rx FIFO */
+
+/* Bit masks for USB_TXTYPE */
+
+#define            TARGET_EP_NO_T  0xf        /* EP number */
+#define                PROTOCOL_T  0xc        /* transfer type */
+
+/* Bit masks for USB_TXINTERVAL */
+
+#define          TX_POLL_INTERVAL  0xff       /* polling interval for selected Tx EP */
+
+/* Bit masks for USB_RXTYPE */
+
+#define            TARGET_EP_NO_R  0xf        /* EP number */
+#define                PROTOCOL_R  0xc        /* transfer type */
+
+/* Bit masks for USB_RXINTERVAL */
+
+#define          RX_POLL_INTERVAL  0xff       /* polling interval for selected Rx EP */
+
+/* Bit masks for USB_DMA_INTERRUPT */
+
+#define                  DMA0_INT  0x1        /* DMA0 pending interrupt */
+#define                 nDMA0_INT  0x0       
+#define                  DMA1_INT  0x2        /* DMA1 pending interrupt */
+#define                 nDMA1_INT  0x0       
+#define                  DMA2_INT  0x4        /* DMA2 pending interrupt */
+#define                 nDMA2_INT  0x0       
+#define                  DMA3_INT  0x8        /* DMA3 pending interrupt */
+#define                 nDMA3_INT  0x0       
+#define                  DMA4_INT  0x10       /* DMA4 pending interrupt */
+#define                 nDMA4_INT  0x0       
+#define                  DMA5_INT  0x20       /* DMA5 pending interrupt */
+#define                 nDMA5_INT  0x0       
+#define                  DMA6_INT  0x40       /* DMA6 pending interrupt */
+#define                 nDMA6_INT  0x0       
+#define                  DMA7_INT  0x80       /* DMA7 pending interrupt */
+#define                 nDMA7_INT  0x0       
+
+/* Bit masks for USB_DMAxCONTROL */
+
+#define                   DMA_ENA  0x1        /* DMA enable */
+#define                  nDMA_ENA  0x0       
+#define                 DIRECTION  0x2        /* direction of DMA transfer */
+#define                nDIRECTION  0x0       
+#define                      MODE  0x4        /* DMA Bus error */
+#define                     nMODE  0x0       
+#define                   INT_ENA  0x8        /* Interrupt enable */
+#define                  nINT_ENA  0x0       
+#define                     EPNUM  0xf0       /* EP number */
+#define                  BUSERROR  0x100      /* DMA Bus error */
+#define                 nBUSERROR  0x0       
+
+/* Bit masks for USB_DMAxADDRHIGH */
+
+#define             DMA_ADDR_HIGH  0xffff     /* Upper 16-bits of memory source/destination address for the DMA master channel */
+
+/* Bit masks for USB_DMAxADDRLOW */
+
+#define              DMA_ADDR_LOW  0xffff     /* Lower 16-bits of memory source/destination address for the DMA master channel */
+
+/* Bit masks for USB_DMAxCOUNTHIGH */
+
+#define            DMA_COUNT_HIGH  0xffff     /* Upper 16-bits of byte count of DMA transfer for DMA master channel */
+
+/* Bit masks for USB_DMAxCOUNTLOW */
+
+#define             DMA_COUNT_LOW  0xffff     /* Lower 16-bits of byte count of DMA transfer for DMA master channel */
+
+#endif /* _DEF_BF527_H */
diff --git a/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h b/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h
new file mode 100644
index 00000000000..fc69cf93f14
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/defBF52x_base.h
@@ -0,0 +1,2014 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/defBF52x_base.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#ifndef _DEF_BF52X_H
+#define _DEF_BF52X_H
+
+
+/* ************************************************************** */
+/*   SYSTEM & MMR ADDRESS DEFINITIONS COMMON TO ALL ADSP-BF52x    */
+/* ************************************************************** */
+
+/* ==== begin from defBF534.h ==== */
+
+/* Clock and System Control	(0xFFC00000 - 0xFFC000FF)								*/
+#define PLL_CTL				0xFFC00000	/* PLL Control Register						*/
+#define PLL_DIV				0xFFC00004	/* PLL Divide Register						*/
+#define VR_CTL				0xFFC00008	/* Voltage Regulator Control Register		*/
+#define PLL_STAT			0xFFC0000C	/* PLL Status Register						*/
+#define PLL_LOCKCNT			0xFFC00010	/* PLL Lock Count Register					*/
+#define CHIPID        0xFFC00014  /* Device ID Register */
+
+
+/* System Interrupt Controller (0xFFC00100 - 0xFFC001FF)							*/
+#define SWRST				0xFFC00100	/* Software Reset Register					*/
+#define SYSCR				0xFFC00104	/* System Configuration Register			*/
+#define SIC_RVECT			0xFFC00108	/* Interrupt Reset Vector Address Register	*/
+
+#define SIC_IMASK0			0xFFC0010C	/* Interrupt Mask Register					*/
+#define SIC_IAR0			0xFFC00110	/* Interrupt Assignment Register 0			*/
+#define SIC_IAR1			0xFFC00114	/* Interrupt Assignment Register 1			*/
+#define SIC_IAR2			0xFFC00118	/* Interrupt Assignment Register 2			*/
+#define SIC_IAR3			0xFFC0011C	/* Interrupt Assignment Register 3			*/
+#define SIC_ISR0				0xFFC00120	/* Interrupt Status Register				*/
+#define SIC_IWR0				0xFFC00124	/* Interrupt Wakeup Register				*/
+
+/* SIC Additions to ADSP-BF52x (0xFFC0014C - 0xFFC00162) */
+#define SIC_IMASK1                      0xFFC0014C     /* Interrupt Mask register of SIC2 */
+#define SIC_IAR4                        0xFFC00150     /* Interrupt Assignment register4 */
+#define SIC_IAR5                        0xFFC00154     /* Interrupt Assignment register5 */
+#define SIC_IAR6                        0xFFC00158     /* Interrupt Assignment register6 */
+#define SIC_IAR7                        0xFFC0015C     /* Interrupt Assignment register7 */
+#define SIC_ISR1                        0xFFC00160     /* Interrupt Statur register */
+#define SIC_IWR1                        0xFFC00164     /* Interrupt Wakeup register */
+
+
+/* Watchdog Timer			(0xFFC00200 - 0xFFC002FF)								*/
+#define WDOG_CTL			0xFFC00200	/* Watchdog Control Register				*/
+#define WDOG_CNT			0xFFC00204	/* Watchdog Count Register					*/
+#define WDOG_STAT			0xFFC00208	/* Watchdog Status Register					*/
+
+
+/* Real Time Clock		(0xFFC00300 - 0xFFC003FF)									*/
+#define RTC_STAT			0xFFC00300	/* RTC Status Register						*/
+#define RTC_ICTL			0xFFC00304	/* RTC Interrupt Control Register			*/
+#define RTC_ISTAT			0xFFC00308	/* RTC Interrupt Status Register			*/
+#define RTC_SWCNT			0xFFC0030C	/* RTC Stopwatch Count Register				*/
+#define RTC_ALARM			0xFFC00310	/* RTC Alarm Time Register					*/
+#define RTC_FAST			0xFFC00314	/* RTC Prescaler Enable Register			*/
+#define RTC_PREN			0xFFC00314	/* RTC Prescaler Enable Alternate Macro		*/
+
+
+/* UART0 Controller		(0xFFC00400 - 0xFFC004FF)									*/
+#define UART0_THR			0xFFC00400	/* Transmit Holding register				*/
+#define UART0_RBR			0xFFC00400	/* Receive Buffer register					*/
+#define UART0_DLL			0xFFC00400	/* Divisor Latch (Low-Byte)					*/
+#define UART0_IER			0xFFC00404	/* Interrupt Enable Register				*/
+#define UART0_DLH			0xFFC00404	/* Divisor Latch (High-Byte)				*/
+#define UART0_IIR			0xFFC00408	/* Interrupt Identification Register		*/
+#define UART0_LCR			0xFFC0040C	/* Line Control Register					*/
+#define UART0_MCR			0xFFC00410	/* Modem Control Register					*/
+#define UART0_LSR			0xFFC00414	/* Line Status Register						*/
+#define UART0_MSR			0xFFC00418	/* Modem Status Register					*/
+#define UART0_SCR			0xFFC0041C	/* SCR Scratch Register						*/
+#define UART0_GCTL			0xFFC00424	/* Global Control Register					*/
+
+
+/* SPI Controller			(0xFFC00500 - 0xFFC005FF)								*/
+#define SPI0_REGBASE			0xFFC00500
+#define SPI_CTL				0xFFC00500	/* SPI Control Register						*/
+#define SPI_FLG				0xFFC00504	/* SPI Flag register						*/
+#define SPI_STAT			0xFFC00508	/* SPI Status register						*/
+#define SPI_TDBR			0xFFC0050C	/* SPI Transmit Data Buffer Register		*/
+#define SPI_RDBR			0xFFC00510	/* SPI Receive Data Buffer Register			*/
+#define SPI_BAUD			0xFFC00514	/* SPI Baud rate Register					*/
+#define SPI_SHADOW			0xFFC00518	/* SPI_RDBR Shadow Register					*/
+
+
+/* TIMER0-7 Registers		(0xFFC00600 - 0xFFC006FF)								*/
+#define TIMER0_CONFIG		0xFFC00600	/* Timer 0 Configuration Register			*/
+#define TIMER0_COUNTER		0xFFC00604	/* Timer 0 Counter Register					*/
+#define TIMER0_PERIOD		0xFFC00608	/* Timer 0 Period Register					*/
+#define TIMER0_WIDTH		0xFFC0060C	/* Timer 0 Width Register					*/
+
+#define TIMER1_CONFIG		0xFFC00610	/* Timer 1 Configuration Register  			*/
+#define TIMER1_COUNTER		0xFFC00614	/* Timer 1 Counter Register        			*/
+#define TIMER1_PERIOD		0xFFC00618	/* Timer 1 Period Register         			*/
+#define TIMER1_WIDTH		0xFFC0061C	/* Timer 1 Width Register          			*/
+
+#define TIMER2_CONFIG		0xFFC00620	/* Timer 2 Configuration Register  			*/
+#define TIMER2_COUNTER		0xFFC00624	/* Timer 2 Counter Register        			*/
+#define TIMER2_PERIOD		0xFFC00628	/* Timer 2 Period Register         			*/
+#define TIMER2_WIDTH		0xFFC0062C	/* Timer 2 Width Register          			*/
+
+#define TIMER3_CONFIG		0xFFC00630	/* Timer 3 Configuration Register			*/
+#define TIMER3_COUNTER		0xFFC00634	/* Timer 3 Counter Register					*/
+#define TIMER3_PERIOD		0xFFC00638	/* Timer 3 Period Register					*/
+#define TIMER3_WIDTH		0xFFC0063C	/* Timer 3 Width Register					*/
+
+#define TIMER4_CONFIG		0xFFC00640	/* Timer 4 Configuration Register  			*/
+#define TIMER4_COUNTER		0xFFC00644	/* Timer 4 Counter Register        			*/
+#define TIMER4_PERIOD		0xFFC00648	/* Timer 4 Period Register         			*/
+#define TIMER4_WIDTH		0xFFC0064C	/* Timer 4 Width Register          			*/
+
+#define TIMER5_CONFIG		0xFFC00650	/* Timer 5 Configuration Register  			*/
+#define TIMER5_COUNTER		0xFFC00654	/* Timer 5 Counter Register        			*/
+#define TIMER5_PERIOD		0xFFC00658	/* Timer 5 Period Register         			*/
+#define TIMER5_WIDTH		0xFFC0065C	/* Timer 5 Width Register          			*/
+
+#define TIMER6_CONFIG		0xFFC00660	/* Timer 6 Configuration Register  			*/
+#define TIMER6_COUNTER		0xFFC00664	/* Timer 6 Counter Register        			*/
+#define TIMER6_PERIOD		0xFFC00668	/* Timer 6 Period Register         			*/
+#define TIMER6_WIDTH		0xFFC0066C	/* Timer 6 Width Register          			*/
+
+#define TIMER7_CONFIG		0xFFC00670	/* Timer 7 Configuration Register  			*/
+#define TIMER7_COUNTER		0xFFC00674	/* Timer 7 Counter Register        			*/
+#define TIMER7_PERIOD		0xFFC00678	/* Timer 7 Period Register         			*/
+#define TIMER7_WIDTH		0xFFC0067C	/* Timer 7 Width Register       			*/   
+
+#define TIMER_ENABLE		0xFFC00680	/* Timer Enable Register					*/
+#define TIMER_DISABLE		0xFFC00684	/* Timer Disable Register					*/
+#define TIMER_STATUS		0xFFC00688	/* Timer Status Register					*/
+
+
+/* General Purpose I/O Port F (0xFFC00700 - 0xFFC007FF)												*/
+#define PORTFIO					0xFFC00700	/* Port F I/O Pin State Specify Register				*/
+#define PORTFIO_CLEAR			0xFFC00704	/* Port F I/O Peripheral Interrupt Clear Register		*/
+#define PORTFIO_SET				0xFFC00708	/* Port F I/O Peripheral Interrupt Set Register			*/
+#define PORTFIO_TOGGLE			0xFFC0070C	/* Port F I/O Pin State Toggle Register					*/
+#define PORTFIO_MASKA			0xFFC00710	/* Port F I/O Mask State Specify Interrupt A Register	*/
+#define PORTFIO_MASKA_CLEAR		0xFFC00714	/* Port F I/O Mask Disable Interrupt A Register			*/
+#define PORTFIO_MASKA_SET		0xFFC00718	/* Port F I/O Mask Enable Interrupt A Register			*/
+#define PORTFIO_MASKA_TOGGLE	0xFFC0071C	/* Port F I/O Mask Toggle Enable Interrupt A Register	*/
+#define PORTFIO_MASKB			0xFFC00720	/* Port F I/O Mask State Specify Interrupt B Register	*/
+#define PORTFIO_MASKB_CLEAR		0xFFC00724	/* Port F I/O Mask Disable Interrupt B Register			*/
+#define PORTFIO_MASKB_SET		0xFFC00728	/* Port F I/O Mask Enable Interrupt B Register			*/
+#define PORTFIO_MASKB_TOGGLE	0xFFC0072C	/* Port F I/O Mask Toggle Enable Interrupt B Register	*/
+#define PORTFIO_DIR				0xFFC00730	/* Port F I/O Direction Register						*/
+#define PORTFIO_POLAR			0xFFC00734	/* Port F I/O Source Polarity Register					*/
+#define PORTFIO_EDGE			0xFFC00738	/* Port F I/O Source Sensitivity Register				*/
+#define PORTFIO_BOTH			0xFFC0073C	/* Port F I/O Set on BOTH Edges Register				*/
+#define PORTFIO_INEN			0xFFC00740	/* Port F I/O Input Enable Register 					*/
+
+
+/* SPORT0 Controller		(0xFFC00800 - 0xFFC008FF)										*/
+#define SPORT0_TCR1			0xFFC00800	/* SPORT0 Transmit Configuration 1 Register			*/
+#define SPORT0_TCR2			0xFFC00804	/* SPORT0 Transmit Configuration 2 Register			*/
+#define SPORT0_TCLKDIV		0xFFC00808	/* SPORT0 Transmit Clock Divider					*/
+#define SPORT0_TFSDIV		0xFFC0080C	/* SPORT0 Transmit Frame Sync Divider				*/
+#define SPORT0_TX			0xFFC00810	/* SPORT0 TX Data Register							*/
+#define SPORT0_RX			0xFFC00818	/* SPORT0 RX Data Register							*/
+#define SPORT0_RCR1			0xFFC00820	/* SPORT0 Transmit Configuration 1 Register			*/
+#define SPORT0_RCR2			0xFFC00824	/* SPORT0 Transmit Configuration 2 Register			*/
+#define SPORT0_RCLKDIV		0xFFC00828	/* SPORT0 Receive Clock Divider						*/
+#define SPORT0_RFSDIV		0xFFC0082C	/* SPORT0 Receive Frame Sync Divider				*/
+#define SPORT0_STAT			0xFFC00830	/* SPORT0 Status Register							*/
+#define SPORT0_CHNL			0xFFC00834	/* SPORT0 Current Channel Register					*/
+#define SPORT0_MCMC1		0xFFC00838	/* SPORT0 Multi-Channel Configuration Register 1	*/
+#define SPORT0_MCMC2		0xFFC0083C	/* SPORT0 Multi-Channel Configuration Register 2	*/
+#define SPORT0_MTCS0		0xFFC00840	/* SPORT0 Multi-Channel Transmit Select Register 0	*/
+#define SPORT0_MTCS1		0xFFC00844	/* SPORT0 Multi-Channel Transmit Select Register 1	*/
+#define SPORT0_MTCS2		0xFFC00848	/* SPORT0 Multi-Channel Transmit Select Register 2	*/
+#define SPORT0_MTCS3		0xFFC0084C	/* SPORT0 Multi-Channel Transmit Select Register 3	*/
+#define SPORT0_MRCS0		0xFFC00850	/* SPORT0 Multi-Channel Receive Select Register 0	*/
+#define SPORT0_MRCS1		0xFFC00854	/* SPORT0 Multi-Channel Receive Select Register 1	*/
+#define SPORT0_MRCS2		0xFFC00858	/* SPORT0 Multi-Channel Receive Select Register 2	*/
+#define SPORT0_MRCS3		0xFFC0085C	/* SPORT0 Multi-Channel Receive Select Register 3	*/
+
+
+/* SPORT1 Controller		(0xFFC00900 - 0xFFC009FF)										*/
+#define SPORT1_TCR1			0xFFC00900	/* SPORT1 Transmit Configuration 1 Register			*/
+#define SPORT1_TCR2			0xFFC00904	/* SPORT1 Transmit Configuration 2 Register			*/
+#define SPORT1_TCLKDIV		0xFFC00908	/* SPORT1 Transmit Clock Divider					*/
+#define SPORT1_TFSDIV		0xFFC0090C	/* SPORT1 Transmit Frame Sync Divider				*/
+#define SPORT1_TX			0xFFC00910	/* SPORT1 TX Data Register							*/
+#define SPORT1_RX			0xFFC00918	/* SPORT1 RX Data Register							*/
+#define SPORT1_RCR1			0xFFC00920	/* SPORT1 Transmit Configuration 1 Register			*/
+#define SPORT1_RCR2			0xFFC00924	/* SPORT1 Transmit Configuration 2 Register			*/
+#define SPORT1_RCLKDIV		0xFFC00928	/* SPORT1 Receive Clock Divider						*/
+#define SPORT1_RFSDIV		0xFFC0092C	/* SPORT1 Receive Frame Sync Divider				*/
+#define SPORT1_STAT			0xFFC00930	/* SPORT1 Status Register							*/
+#define SPORT1_CHNL			0xFFC00934	/* SPORT1 Current Channel Register					*/
+#define SPORT1_MCMC1		0xFFC00938	/* SPORT1 Multi-Channel Configuration Register 1	*/
+#define SPORT1_MCMC2		0xFFC0093C	/* SPORT1 Multi-Channel Configuration Register 2	*/
+#define SPORT1_MTCS0		0xFFC00940	/* SPORT1 Multi-Channel Transmit Select Register 0	*/
+#define SPORT1_MTCS1		0xFFC00944	/* SPORT1 Multi-Channel Transmit Select Register 1	*/
+#define SPORT1_MTCS2		0xFFC00948	/* SPORT1 Multi-Channel Transmit Select Register 2	*/
+#define SPORT1_MTCS3		0xFFC0094C	/* SPORT1 Multi-Channel Transmit Select Register 3	*/
+#define SPORT1_MRCS0		0xFFC00950	/* SPORT1 Multi-Channel Receive Select Register 0	*/
+#define SPORT1_MRCS1		0xFFC00954	/* SPORT1 Multi-Channel Receive Select Register 1	*/
+#define SPORT1_MRCS2		0xFFC00958	/* SPORT1 Multi-Channel Receive Select Register 2	*/
+#define SPORT1_MRCS3		0xFFC0095C	/* SPORT1 Multi-Channel Receive Select Register 3	*/
+
+
+/* External Bus Interface Unit (0xFFC00A00 - 0xFFC00AFF)								*/
+#define EBIU_AMGCTL			0xFFC00A00	/* Asynchronous Memory Global Control Register	*/
+#define EBIU_AMBCTL0		0xFFC00A04	/* Asynchronous Memory Bank Control Register 0	*/
+#define EBIU_AMBCTL1		0xFFC00A08	/* Asynchronous Memory Bank Control Register 1	*/
+#define EBIU_SDGCTL			0xFFC00A10	/* SDRAM Global Control Register				*/
+#define EBIU_SDBCTL			0xFFC00A14	/* SDRAM Bank Control Register					*/
+#define EBIU_SDRRC			0xFFC00A18	/* SDRAM Refresh Rate Control Register			*/
+#define EBIU_SDSTAT			0xFFC00A1C	/* SDRAM Status Register						*/
+
+
+/* DMA Traffic Control Registers													*/
+#define DMA_TC_PER			0xFFC00B0C	/* Traffic Control Periods Register			*/
+#define DMA_TC_CNT			0xFFC00B10	/* Traffic Control Current Counts Register	*/
+
+/* Alternate deprecated register names (below) provided for backwards code compatibility */
+#define DMA_TCPER			0xFFC00B0C	/* Traffic Control Periods Register			*/
+#define DMA_TCCNT			0xFFC00B10	/* Traffic Control Current Counts Register	*/
+
+/* DMA Controller (0xFFC00C00 - 0xFFC00FFF)															*/
+#define DMA0_NEXT_DESC_PTR		0xFFC00C00	/* DMA Channel 0 Next Descriptor Pointer Register		*/
+#define DMA0_START_ADDR			0xFFC00C04	/* DMA Channel 0 Start Address Register					*/
+#define DMA0_CONFIG				0xFFC00C08	/* DMA Channel 0 Configuration Register					*/
+#define DMA0_X_COUNT			0xFFC00C10	/* DMA Channel 0 X Count Register						*/
+#define DMA0_X_MODIFY			0xFFC00C14	/* DMA Channel 0 X Modify Register						*/
+#define DMA0_Y_COUNT			0xFFC00C18	/* DMA Channel 0 Y Count Register						*/
+#define DMA0_Y_MODIFY			0xFFC00C1C	/* DMA Channel 0 Y Modify Register						*/
+#define DMA0_CURR_DESC_PTR		0xFFC00C20	/* DMA Channel 0 Current Descriptor Pointer Register	*/
+#define DMA0_CURR_ADDR			0xFFC00C24	/* DMA Channel 0 Current Address Register				*/
+#define DMA0_IRQ_STATUS			0xFFC00C28	/* DMA Channel 0 Interrupt/Status Register				*/
+#define DMA0_PERIPHERAL_MAP		0xFFC00C2C	/* DMA Channel 0 Peripheral Map Register				*/
+#define DMA0_CURR_X_COUNT		0xFFC00C30	/* DMA Channel 0 Current X Count Register				*/
+#define DMA0_CURR_Y_COUNT		0xFFC00C38	/* DMA Channel 0 Current Y Count Register				*/
+
+#define DMA1_NEXT_DESC_PTR		0xFFC00C40	/* DMA Channel 1 Next Descriptor Pointer Register		*/
+#define DMA1_START_ADDR			0xFFC00C44	/* DMA Channel 1 Start Address Register					*/
+#define DMA1_CONFIG				0xFFC00C48	/* DMA Channel 1 Configuration Register					*/
+#define DMA1_X_COUNT			0xFFC00C50	/* DMA Channel 1 X Count Register						*/
+#define DMA1_X_MODIFY			0xFFC00C54	/* DMA Channel 1 X Modify Register						*/
+#define DMA1_Y_COUNT			0xFFC00C58	/* DMA Channel 1 Y Count Register						*/
+#define DMA1_Y_MODIFY			0xFFC00C5C	/* DMA Channel 1 Y Modify Register						*/
+#define DMA1_CURR_DESC_PTR		0xFFC00C60	/* DMA Channel 1 Current Descriptor Pointer Register	*/
+#define DMA1_CURR_ADDR			0xFFC00C64	/* DMA Channel 1 Current Address Register				*/
+#define DMA1_IRQ_STATUS			0xFFC00C68	/* DMA Channel 1 Interrupt/Status Register				*/
+#define DMA1_PERIPHERAL_MAP		0xFFC00C6C	/* DMA Channel 1 Peripheral Map Register				*/
+#define DMA1_CURR_X_COUNT		0xFFC00C70	/* DMA Channel 1 Current X Count Register				*/
+#define DMA1_CURR_Y_COUNT		0xFFC00C78	/* DMA Channel 1 Current Y Count Register				*/
+
+#define DMA2_NEXT_DESC_PTR		0xFFC00C80	/* DMA Channel 2 Next Descriptor Pointer Register		*/
+#define DMA2_START_ADDR			0xFFC00C84	/* DMA Channel 2 Start Address Register					*/
+#define DMA2_CONFIG				0xFFC00C88	/* DMA Channel 2 Configuration Register					*/
+#define DMA2_X_COUNT			0xFFC00C90	/* DMA Channel 2 X Count Register						*/
+#define DMA2_X_MODIFY			0xFFC00C94	/* DMA Channel 2 X Modify Register						*/
+#define DMA2_Y_COUNT			0xFFC00C98	/* DMA Channel 2 Y Count Register						*/
+#define DMA2_Y_MODIFY			0xFFC00C9C	/* DMA Channel 2 Y Modify Register						*/
+#define DMA2_CURR_DESC_PTR		0xFFC00CA0	/* DMA Channel 2 Current Descriptor Pointer Register	*/
+#define DMA2_CURR_ADDR			0xFFC00CA4	/* DMA Channel 2 Current Address Register				*/
+#define DMA2_IRQ_STATUS			0xFFC00CA8	/* DMA Channel 2 Interrupt/Status Register				*/
+#define DMA2_PERIPHERAL_MAP		0xFFC00CAC	/* DMA Channel 2 Peripheral Map Register				*/
+#define DMA2_CURR_X_COUNT		0xFFC00CB0	/* DMA Channel 2 Current X Count Register				*/
+#define DMA2_CURR_Y_COUNT		0xFFC00CB8	/* DMA Channel 2 Current Y Count Register				*/
+
+#define DMA3_NEXT_DESC_PTR		0xFFC00CC0	/* DMA Channel 3 Next Descriptor Pointer Register		*/
+#define DMA3_START_ADDR			0xFFC00CC4	/* DMA Channel 3 Start Address Register					*/
+#define DMA3_CONFIG				0xFFC00CC8	/* DMA Channel 3 Configuration Register					*/
+#define DMA3_X_COUNT			0xFFC00CD0	/* DMA Channel 3 X Count Register						*/
+#define DMA3_X_MODIFY			0xFFC00CD4	/* DMA Channel 3 X Modify Register						*/
+#define DMA3_Y_COUNT			0xFFC00CD8	/* DMA Channel 3 Y Count Register						*/
+#define DMA3_Y_MODIFY			0xFFC00CDC	/* DMA Channel 3 Y Modify Register						*/
+#define DMA3_CURR_DESC_PTR		0xFFC00CE0	/* DMA Channel 3 Current Descriptor Pointer Register	*/
+#define DMA3_CURR_ADDR			0xFFC00CE4	/* DMA Channel 3 Current Address Register				*/
+#define DMA3_IRQ_STATUS			0xFFC00CE8	/* DMA Channel 3 Interrupt/Status Register				*/
+#define DMA3_PERIPHERAL_MAP		0xFFC00CEC	/* DMA Channel 3 Peripheral Map Register				*/
+#define DMA3_CURR_X_COUNT		0xFFC00CF0	/* DMA Channel 3 Current X Count Register				*/
+#define DMA3_CURR_Y_COUNT		0xFFC00CF8	/* DMA Channel 3 Current Y Count Register				*/
+
+#define DMA4_NEXT_DESC_PTR		0xFFC00D00	/* DMA Channel 4 Next Descriptor Pointer Register		*/
+#define DMA4_START_ADDR			0xFFC00D04	/* DMA Channel 4 Start Address Register					*/
+#define DMA4_CONFIG				0xFFC00D08	/* DMA Channel 4 Configuration Register					*/
+#define DMA4_X_COUNT			0xFFC00D10	/* DMA Channel 4 X Count Register						*/
+#define DMA4_X_MODIFY			0xFFC00D14	/* DMA Channel 4 X Modify Register						*/
+#define DMA4_Y_COUNT			0xFFC00D18	/* DMA Channel 4 Y Count Register						*/
+#define DMA4_Y_MODIFY			0xFFC00D1C	/* DMA Channel 4 Y Modify Register						*/
+#define DMA4_CURR_DESC_PTR		0xFFC00D20	/* DMA Channel 4 Current Descriptor Pointer Register	*/
+#define DMA4_CURR_ADDR			0xFFC00D24	/* DMA Channel 4 Current Address Register				*/
+#define DMA4_IRQ_STATUS			0xFFC00D28	/* DMA Channel 4 Interrupt/Status Register				*/
+#define DMA4_PERIPHERAL_MAP		0xFFC00D2C	/* DMA Channel 4 Peripheral Map Register				*/
+#define DMA4_CURR_X_COUNT		0xFFC00D30	/* DMA Channel 4 Current X Count Register				*/
+#define DMA4_CURR_Y_COUNT		0xFFC00D38	/* DMA Channel 4 Current Y Count Register				*/
+
+#define DMA5_NEXT_DESC_PTR		0xFFC00D40	/* DMA Channel 5 Next Descriptor Pointer Register		*/
+#define DMA5_START_ADDR			0xFFC00D44	/* DMA Channel 5 Start Address Register					*/
+#define DMA5_CONFIG				0xFFC00D48	/* DMA Channel 5 Configuration Register					*/
+#define DMA5_X_COUNT			0xFFC00D50	/* DMA Channel 5 X Count Register						*/
+#define DMA5_X_MODIFY			0xFFC00D54	/* DMA Channel 5 X Modify Register						*/
+#define DMA5_Y_COUNT			0xFFC00D58	/* DMA Channel 5 Y Count Register						*/
+#define DMA5_Y_MODIFY			0xFFC00D5C	/* DMA Channel 5 Y Modify Register						*/
+#define DMA5_CURR_DESC_PTR		0xFFC00D60	/* DMA Channel 5 Current Descriptor Pointer Register	*/
+#define DMA5_CURR_ADDR			0xFFC00D64	/* DMA Channel 5 Current Address Register				*/
+#define DMA5_IRQ_STATUS			0xFFC00D68	/* DMA Channel 5 Interrupt/Status Register				*/
+#define DMA5_PERIPHERAL_MAP		0xFFC00D6C	/* DMA Channel 5 Peripheral Map Register				*/
+#define DMA5_CURR_X_COUNT		0xFFC00D70	/* DMA Channel 5 Current X Count Register				*/
+#define DMA5_CURR_Y_COUNT		0xFFC00D78	/* DMA Channel 5 Current Y Count Register				*/
+
+#define DMA6_NEXT_DESC_PTR		0xFFC00D80	/* DMA Channel 6 Next Descriptor Pointer Register		*/
+#define DMA6_START_ADDR			0xFFC00D84	/* DMA Channel 6 Start Address Register					*/
+#define DMA6_CONFIG				0xFFC00D88	/* DMA Channel 6 Configuration Register					*/
+#define DMA6_X_COUNT			0xFFC00D90	/* DMA Channel 6 X Count Register						*/
+#define DMA6_X_MODIFY			0xFFC00D94	/* DMA Channel 6 X Modify Register						*/
+#define DMA6_Y_COUNT			0xFFC00D98	/* DMA Channel 6 Y Count Register						*/
+#define DMA6_Y_MODIFY			0xFFC00D9C	/* DMA Channel 6 Y Modify Register						*/
+#define DMA6_CURR_DESC_PTR		0xFFC00DA0	/* DMA Channel 6 Current Descriptor Pointer Register	*/
+#define DMA6_CURR_ADDR			0xFFC00DA4	/* DMA Channel 6 Current Address Register				*/
+#define DMA6_IRQ_STATUS			0xFFC00DA8	/* DMA Channel 6 Interrupt/Status Register				*/
+#define DMA6_PERIPHERAL_MAP		0xFFC00DAC	/* DMA Channel 6 Peripheral Map Register				*/
+#define DMA6_CURR_X_COUNT		0xFFC00DB0	/* DMA Channel 6 Current X Count Register				*/
+#define DMA6_CURR_Y_COUNT		0xFFC00DB8	/* DMA Channel 6 Current Y Count Register				*/
+
+#define DMA7_NEXT_DESC_PTR		0xFFC00DC0	/* DMA Channel 7 Next Descriptor Pointer Register		*/
+#define DMA7_START_ADDR			0xFFC00DC4	/* DMA Channel 7 Start Address Register					*/
+#define DMA7_CONFIG				0xFFC00DC8	/* DMA Channel 7 Configuration Register					*/
+#define DMA7_X_COUNT			0xFFC00DD0	/* DMA Channel 7 X Count Register						*/
+#define DMA7_X_MODIFY			0xFFC00DD4	/* DMA Channel 7 X Modify Register						*/
+#define DMA7_Y_COUNT			0xFFC00DD8	/* DMA Channel 7 Y Count Register						*/
+#define DMA7_Y_MODIFY			0xFFC00DDC	/* DMA Channel 7 Y Modify Register						*/
+#define DMA7_CURR_DESC_PTR		0xFFC00DE0	/* DMA Channel 7 Current Descriptor Pointer Register	*/
+#define DMA7_CURR_ADDR			0xFFC00DE4	/* DMA Channel 7 Current Address Register				*/
+#define DMA7_IRQ_STATUS			0xFFC00DE8	/* DMA Channel 7 Interrupt/Status Register				*/
+#define DMA7_PERIPHERAL_MAP		0xFFC00DEC	/* DMA Channel 7 Peripheral Map Register				*/
+#define DMA7_CURR_X_COUNT		0xFFC00DF0	/* DMA Channel 7 Current X Count Register				*/
+#define DMA7_CURR_Y_COUNT		0xFFC00DF8	/* DMA Channel 7 Current Y Count Register				*/
+
+#define DMA8_NEXT_DESC_PTR		0xFFC00E00	/* DMA Channel 8 Next Descriptor Pointer Register		*/
+#define DMA8_START_ADDR			0xFFC00E04	/* DMA Channel 8 Start Address Register					*/
+#define DMA8_CONFIG				0xFFC00E08	/* DMA Channel 8 Configuration Register					*/
+#define DMA8_X_COUNT			0xFFC00E10	/* DMA Channel 8 X Count Register						*/
+#define DMA8_X_MODIFY			0xFFC00E14	/* DMA Channel 8 X Modify Register						*/
+#define DMA8_Y_COUNT			0xFFC00E18	/* DMA Channel 8 Y Count Register						*/
+#define DMA8_Y_MODIFY			0xFFC00E1C	/* DMA Channel 8 Y Modify Register						*/
+#define DMA8_CURR_DESC_PTR		0xFFC00E20	/* DMA Channel 8 Current Descriptor Pointer Register	*/
+#define DMA8_CURR_ADDR			0xFFC00E24	/* DMA Channel 8 Current Address Register				*/
+#define DMA8_IRQ_STATUS			0xFFC00E28	/* DMA Channel 8 Interrupt/Status Register				*/
+#define DMA8_PERIPHERAL_MAP		0xFFC00E2C	/* DMA Channel 8 Peripheral Map Register				*/
+#define DMA8_CURR_X_COUNT		0xFFC00E30	/* DMA Channel 8 Current X Count Register				*/
+#define DMA8_CURR_Y_COUNT		0xFFC00E38	/* DMA Channel 8 Current Y Count Register				*/
+
+#define DMA9_NEXT_DESC_PTR		0xFFC00E40	/* DMA Channel 9 Next Descriptor Pointer Register		*/
+#define DMA9_START_ADDR			0xFFC00E44	/* DMA Channel 9 Start Address Register					*/
+#define DMA9_CONFIG				0xFFC00E48	/* DMA Channel 9 Configuration Register					*/
+#define DMA9_X_COUNT			0xFFC00E50	/* DMA Channel 9 X Count Register						*/
+#define DMA9_X_MODIFY			0xFFC00E54	/* DMA Channel 9 X Modify Register						*/
+#define DMA9_Y_COUNT			0xFFC00E58	/* DMA Channel 9 Y Count Register						*/
+#define DMA9_Y_MODIFY			0xFFC00E5C	/* DMA Channel 9 Y Modify Register						*/
+#define DMA9_CURR_DESC_PTR		0xFFC00E60	/* DMA Channel 9 Current Descriptor Pointer Register	*/
+#define DMA9_CURR_ADDR			0xFFC00E64	/* DMA Channel 9 Current Address Register				*/
+#define DMA9_IRQ_STATUS			0xFFC00E68	/* DMA Channel 9 Interrupt/Status Register				*/
+#define DMA9_PERIPHERAL_MAP		0xFFC00E6C	/* DMA Channel 9 Peripheral Map Register				*/
+#define DMA9_CURR_X_COUNT		0xFFC00E70	/* DMA Channel 9 Current X Count Register				*/
+#define DMA9_CURR_Y_COUNT		0xFFC00E78	/* DMA Channel 9 Current Y Count Register				*/
+
+#define DMA10_NEXT_DESC_PTR		0xFFC00E80	/* DMA Channel 10 Next Descriptor Pointer Register		*/
+#define DMA10_START_ADDR		0xFFC00E84	/* DMA Channel 10 Start Address Register				*/
+#define DMA10_CONFIG			0xFFC00E88	/* DMA Channel 10 Configuration Register				*/
+#define DMA10_X_COUNT			0xFFC00E90	/* DMA Channel 10 X Count Register						*/
+#define DMA10_X_MODIFY			0xFFC00E94	/* DMA Channel 10 X Modify Register						*/
+#define DMA10_Y_COUNT			0xFFC00E98	/* DMA Channel 10 Y Count Register						*/
+#define DMA10_Y_MODIFY			0xFFC00E9C	/* DMA Channel 10 Y Modify Register						*/
+#define DMA10_CURR_DESC_PTR		0xFFC00EA0	/* DMA Channel 10 Current Descriptor Pointer Register	*/
+#define DMA10_CURR_ADDR			0xFFC00EA4	/* DMA Channel 10 Current Address Register				*/
+#define DMA10_IRQ_STATUS		0xFFC00EA8	/* DMA Channel 10 Interrupt/Status Register				*/
+#define DMA10_PERIPHERAL_MAP	0xFFC00EAC	/* DMA Channel 10 Peripheral Map Register				*/
+#define DMA10_CURR_X_COUNT		0xFFC00EB0	/* DMA Channel 10 Current X Count Register				*/
+#define DMA10_CURR_Y_COUNT		0xFFC00EB8	/* DMA Channel 10 Current Y Count Register				*/
+
+#define DMA11_NEXT_DESC_PTR		0xFFC00EC0	/* DMA Channel 11 Next Descriptor Pointer Register		*/
+#define DMA11_START_ADDR		0xFFC00EC4	/* DMA Channel 11 Start Address Register				*/
+#define DMA11_CONFIG			0xFFC00EC8	/* DMA Channel 11 Configuration Register				*/
+#define DMA11_X_COUNT			0xFFC00ED0	/* DMA Channel 11 X Count Register						*/
+#define DMA11_X_MODIFY			0xFFC00ED4	/* DMA Channel 11 X Modify Register						*/
+#define DMA11_Y_COUNT			0xFFC00ED8	/* DMA Channel 11 Y Count Register						*/
+#define DMA11_Y_MODIFY			0xFFC00EDC	/* DMA Channel 11 Y Modify Register						*/
+#define DMA11_CURR_DESC_PTR		0xFFC00EE0	/* DMA Channel 11 Current Descriptor Pointer Register	*/
+#define DMA11_CURR_ADDR			0xFFC00EE4	/* DMA Channel 11 Current Address Register				*/
+#define DMA11_IRQ_STATUS		0xFFC00EE8	/* DMA Channel 11 Interrupt/Status Register				*/
+#define DMA11_PERIPHERAL_MAP	0xFFC00EEC	/* DMA Channel 11 Peripheral Map Register				*/
+#define DMA11_CURR_X_COUNT		0xFFC00EF0	/* DMA Channel 11 Current X Count Register				*/
+#define DMA11_CURR_Y_COUNT		0xFFC00EF8	/* DMA Channel 11 Current Y Count Register				*/
+
+#define MDMA_D0_NEXT_DESC_PTR	0xFFC00F00	/* MemDMA Stream 0 Destination Next Descriptor Pointer Register		*/
+#define MDMA_D0_START_ADDR		0xFFC00F04	/* MemDMA Stream 0 Destination Start Address Register				*/
+#define MDMA_D0_CONFIG			0xFFC00F08	/* MemDMA Stream 0 Destination Configuration Register				*/
+#define MDMA_D0_X_COUNT			0xFFC00F10	/* MemDMA Stream 0 Destination X Count Register						*/
+#define MDMA_D0_X_MODIFY		0xFFC00F14	/* MemDMA Stream 0 Destination X Modify Register					*/
+#define MDMA_D0_Y_COUNT			0xFFC00F18	/* MemDMA Stream 0 Destination Y Count Register						*/
+#define MDMA_D0_Y_MODIFY		0xFFC00F1C	/* MemDMA Stream 0 Destination Y Modify Register					*/
+#define MDMA_D0_CURR_DESC_PTR	0xFFC00F20	/* MemDMA Stream 0 Destination Current Descriptor Pointer Register	*/
+#define MDMA_D0_CURR_ADDR		0xFFC00F24	/* MemDMA Stream 0 Destination Current Address Register				*/
+#define MDMA_D0_IRQ_STATUS		0xFFC00F28	/* MemDMA Stream 0 Destination Interrupt/Status Register			*/
+#define MDMA_D0_PERIPHERAL_MAP	0xFFC00F2C	/* MemDMA Stream 0 Destination Peripheral Map Register				*/
+#define MDMA_D0_CURR_X_COUNT	0xFFC00F30	/* MemDMA Stream 0 Destination Current X Count Register				*/
+#define MDMA_D0_CURR_Y_COUNT	0xFFC00F38	/* MemDMA Stream 0 Destination Current Y Count Register				*/
+
+#define MDMA_S0_NEXT_DESC_PTR	0xFFC00F40	/* MemDMA Stream 0 Source Next Descriptor Pointer Register			*/
+#define MDMA_S0_START_ADDR		0xFFC00F44	/* MemDMA Stream 0 Source Start Address Register					*/
+#define MDMA_S0_CONFIG			0xFFC00F48	/* MemDMA Stream 0 Source Configuration Register					*/
+#define MDMA_S0_X_COUNT			0xFFC00F50	/* MemDMA Stream 0 Source X Count Register							*/
+#define MDMA_S0_X_MODIFY		0xFFC00F54	/* MemDMA Stream 0 Source X Modify Register							*/
+#define MDMA_S0_Y_COUNT			0xFFC00F58	/* MemDMA Stream 0 Source Y Count Register							*/
+#define MDMA_S0_Y_MODIFY		0xFFC00F5C	/* MemDMA Stream 0 Source Y Modify Register							*/
+#define MDMA_S0_CURR_DESC_PTR	0xFFC00F60	/* MemDMA Stream 0 Source Current Descriptor Pointer Register		*/
+#define MDMA_S0_CURR_ADDR		0xFFC00F64	/* MemDMA Stream 0 Source Current Address Register					*/
+#define MDMA_S0_IRQ_STATUS		0xFFC00F68	/* MemDMA Stream 0 Source Interrupt/Status Register					*/
+#define MDMA_S0_PERIPHERAL_MAP	0xFFC00F6C	/* MemDMA Stream 0 Source Peripheral Map Register					*/
+#define MDMA_S0_CURR_X_COUNT	0xFFC00F70	/* MemDMA Stream 0 Source Current X Count Register					*/
+#define MDMA_S0_CURR_Y_COUNT	0xFFC00F78	/* MemDMA Stream 0 Source Current Y Count Register					*/
+
+#define MDMA_D1_NEXT_DESC_PTR	0xFFC00F80	/* MemDMA Stream 1 Destination Next Descriptor Pointer Register		*/
+#define MDMA_D1_START_ADDR		0xFFC00F84	/* MemDMA Stream 1 Destination Start Address Register				*/
+#define MDMA_D1_CONFIG			0xFFC00F88	/* MemDMA Stream 1 Destination Configuration Register				*/
+#define MDMA_D1_X_COUNT			0xFFC00F90	/* MemDMA Stream 1 Destination X Count Register						*/
+#define MDMA_D1_X_MODIFY		0xFFC00F94	/* MemDMA Stream 1 Destination X Modify Register					*/
+#define MDMA_D1_Y_COUNT			0xFFC00F98	/* MemDMA Stream 1 Destination Y Count Register						*/
+#define MDMA_D1_Y_MODIFY		0xFFC00F9C	/* MemDMA Stream 1 Destination Y Modify Register					*/
+#define MDMA_D1_CURR_DESC_PTR	0xFFC00FA0	/* MemDMA Stream 1 Destination Current Descriptor Pointer Register	*/
+#define MDMA_D1_CURR_ADDR		0xFFC00FA4	/* MemDMA Stream 1 Destination Current Address Register				*/
+#define MDMA_D1_IRQ_STATUS		0xFFC00FA8	/* MemDMA Stream 1 Destination Interrupt/Status Register			*/
+#define MDMA_D1_PERIPHERAL_MAP	0xFFC00FAC	/* MemDMA Stream 1 Destination Peripheral Map Register				*/
+#define MDMA_D1_CURR_X_COUNT	0xFFC00FB0	/* MemDMA Stream 1 Destination Current X Count Register				*/
+#define MDMA_D1_CURR_Y_COUNT	0xFFC00FB8	/* MemDMA Stream 1 Destination Current Y Count Register				*/
+
+#define MDMA_S1_NEXT_DESC_PTR	0xFFC00FC0	/* MemDMA Stream 1 Source Next Descriptor Pointer Register			*/
+#define MDMA_S1_START_ADDR		0xFFC00FC4	/* MemDMA Stream 1 Source Start Address Register					*/
+#define MDMA_S1_CONFIG			0xFFC00FC8	/* MemDMA Stream 1 Source Configuration Register					*/
+#define MDMA_S1_X_COUNT			0xFFC00FD0	/* MemDMA Stream 1 Source X Count Register							*/
+#define MDMA_S1_X_MODIFY		0xFFC00FD4	/* MemDMA Stream 1 Source X Modify Register							*/
+#define MDMA_S1_Y_COUNT			0xFFC00FD8	/* MemDMA Stream 1 Source Y Count Register							*/
+#define MDMA_S1_Y_MODIFY		0xFFC00FDC	/* MemDMA Stream 1 Source Y Modify Register							*/
+#define MDMA_S1_CURR_DESC_PTR	0xFFC00FE0	/* MemDMA Stream 1 Source Current Descriptor Pointer Register		*/
+#define MDMA_S1_CURR_ADDR		0xFFC00FE4	/* MemDMA Stream 1 Source Current Address Register					*/
+#define MDMA_S1_IRQ_STATUS		0xFFC00FE8	/* MemDMA Stream 1 Source Interrupt/Status Register					*/
+#define MDMA_S1_PERIPHERAL_MAP	0xFFC00FEC	/* MemDMA Stream 1 Source Peripheral Map Register					*/
+#define MDMA_S1_CURR_X_COUNT	0xFFC00FF0	/* MemDMA Stream 1 Source Current X Count Register					*/
+#define MDMA_S1_CURR_Y_COUNT	0xFFC00FF8	/* MemDMA Stream 1 Source Current Y Count Register					*/
+
+
+/* Parallel Peripheral Interface (0xFFC01000 - 0xFFC010FF)				*/
+#define PPI_CONTROL			0xFFC01000	/* PPI Control Register			*/
+#define PPI_STATUS			0xFFC01004	/* PPI Status Register			*/
+#define PPI_COUNT			0xFFC01008	/* PPI Transfer Count Register	*/
+#define PPI_DELAY			0xFFC0100C	/* PPI Delay Count Register		*/
+#define PPI_FRAME			0xFFC01010	/* PPI Frame Length Register	*/
+
+
+/* Two-Wire Interface		(0xFFC01400 - 0xFFC014FF)								*/
+#define TWI0_REGBASE			0xFFC01400
+#define TWI_CLKDIV			0xFFC01400	/* Serial Clock Divider Register			*/
+#define TWI_CONTROL			0xFFC01404	/* TWI Control Register						*/
+#define TWI_SLAVE_CTL		0xFFC01408	/* Slave Mode Control Register				*/
+#define TWI_SLAVE_STAT		0xFFC0140C	/* Slave Mode Status Register				*/
+#define TWI_SLAVE_ADDR		0xFFC01410	/* Slave Mode Address Register				*/
+#define TWI_MASTER_CTL		0xFFC01414	/* Master Mode Control Register				*/
+#define TWI_MASTER_STAT		0xFFC01418	/* Master Mode Status Register				*/
+#define TWI_MASTER_ADDR		0xFFC0141C	/* Master Mode Address Register				*/
+#define TWI_INT_STAT		0xFFC01420	/* TWI Interrupt Status Register			*/
+#define TWI_INT_MASK		0xFFC01424	/* TWI Master Interrupt Mask Register		*/
+#define TWI_FIFO_CTL		0xFFC01428	/* FIFO Control Register					*/
+#define TWI_FIFO_STAT		0xFFC0142C	/* FIFO Status Register						*/
+#define TWI_XMT_DATA8		0xFFC01480	/* FIFO Transmit Data Single Byte Register	*/
+#define TWI_XMT_DATA16		0xFFC01484	/* FIFO Transmit Data Double Byte Register	*/
+#define TWI_RCV_DATA8		0xFFC01488	/* FIFO Receive Data Single Byte Register	*/
+#define TWI_RCV_DATA16		0xFFC0148C	/* FIFO Receive Data Double Byte Register	*/
+
+
+/* General Purpose I/O Port G (0xFFC01500 - 0xFFC015FF)												*/
+#define PORTGIO					0xFFC01500	/* Port G I/O Pin State Specify Register				*/
+#define PORTGIO_CLEAR			0xFFC01504	/* Port G I/O Peripheral Interrupt Clear Register		*/
+#define PORTGIO_SET				0xFFC01508	/* Port G I/O Peripheral Interrupt Set Register			*/
+#define PORTGIO_TOGGLE			0xFFC0150C	/* Port G I/O Pin State Toggle Register					*/
+#define PORTGIO_MASKA			0xFFC01510	/* Port G I/O Mask State Specify Interrupt A Register	*/
+#define PORTGIO_MASKA_CLEAR		0xFFC01514	/* Port G I/O Mask Disable Interrupt A Register			*/
+#define PORTGIO_MASKA_SET		0xFFC01518	/* Port G I/O Mask Enable Interrupt A Register			*/
+#define PORTGIO_MASKA_TOGGLE	0xFFC0151C	/* Port G I/O Mask Toggle Enable Interrupt A Register	*/
+#define PORTGIO_MASKB			0xFFC01520	/* Port G I/O Mask State Specify Interrupt B Register	*/
+#define PORTGIO_MASKB_CLEAR		0xFFC01524	/* Port G I/O Mask Disable Interrupt B Register			*/
+#define PORTGIO_MASKB_SET		0xFFC01528	/* Port G I/O Mask Enable Interrupt B Register			*/
+#define PORTGIO_MASKB_TOGGLE	0xFFC0152C	/* Port G I/O Mask Toggle Enable Interrupt B Register	*/
+#define PORTGIO_DIR				0xFFC01530	/* Port G I/O Direction Register						*/
+#define PORTGIO_POLAR			0xFFC01534	/* Port G I/O Source Polarity Register					*/
+#define PORTGIO_EDGE			0xFFC01538	/* Port G I/O Source Sensitivity Register				*/
+#define PORTGIO_BOTH			0xFFC0153C	/* Port G I/O Set on BOTH Edges Register				*/
+#define PORTGIO_INEN			0xFFC01540	/* Port G I/O Input Enable Register						*/
+
+
+/* General Purpose I/O Port H (0xFFC01700 - 0xFFC017FF)												*/
+#define PORTHIO					0xFFC01700	/* Port H I/O Pin State Specify Register				*/
+#define PORTHIO_CLEAR			0xFFC01704	/* Port H I/O Peripheral Interrupt Clear Register		*/
+#define PORTHIO_SET				0xFFC01708	/* Port H I/O Peripheral Interrupt Set Register			*/
+#define PORTHIO_TOGGLE			0xFFC0170C	/* Port H I/O Pin State Toggle Register					*/
+#define PORTHIO_MASKA			0xFFC01710	/* Port H I/O Mask State Specify Interrupt A Register	*/
+#define PORTHIO_MASKA_CLEAR		0xFFC01714	/* Port H I/O Mask Disable Interrupt A Register			*/
+#define PORTHIO_MASKA_SET		0xFFC01718	/* Port H I/O Mask Enable Interrupt A Register			*/
+#define PORTHIO_MASKA_TOGGLE	0xFFC0171C	/* Port H I/O Mask Toggle Enable Interrupt A Register	*/
+#define PORTHIO_MASKB			0xFFC01720	/* Port H I/O Mask State Specify Interrupt B Register	*/
+#define PORTHIO_MASKB_CLEAR		0xFFC01724	/* Port H I/O Mask Disable Interrupt B Register			*/
+#define PORTHIO_MASKB_SET		0xFFC01728	/* Port H I/O Mask Enable Interrupt B Register			*/
+#define PORTHIO_MASKB_TOGGLE	0xFFC0172C	/* Port H I/O Mask Toggle Enable Interrupt B Register	*/
+#define PORTHIO_DIR				0xFFC01730	/* Port H I/O Direction Register						*/
+#define PORTHIO_POLAR			0xFFC01734	/* Port H I/O Source Polarity Register					*/
+#define PORTHIO_EDGE			0xFFC01738	/* Port H I/O Source Sensitivity Register				*/
+#define PORTHIO_BOTH			0xFFC0173C	/* Port H I/O Set on BOTH Edges Register				*/
+#define PORTHIO_INEN			0xFFC01740	/* Port H I/O Input Enable Register						*/
+
+
+/* UART1 Controller		(0xFFC02000 - 0xFFC020FF)								*/
+#define UART1_THR			0xFFC02000	/* Transmit Holding register			*/
+#define UART1_RBR			0xFFC02000	/* Receive Buffer register				*/
+#define UART1_DLL			0xFFC02000	/* Divisor Latch (Low-Byte)				*/
+#define UART1_IER			0xFFC02004	/* Interrupt Enable Register			*/
+#define UART1_DLH			0xFFC02004	/* Divisor Latch (High-Byte)			*/
+#define UART1_IIR			0xFFC02008	/* Interrupt Identification Register	*/
+#define UART1_LCR			0xFFC0200C	/* Line Control Register				*/
+#define UART1_MCR			0xFFC02010	/* Modem Control Register				*/
+#define UART1_LSR			0xFFC02014	/* Line Status Register					*/
+#define UART1_MSR			0xFFC02018	/* Modem Status Register				*/
+#define UART1_SCR			0xFFC0201C	/* SCR Scratch Register					*/
+#define UART1_GCTL			0xFFC02024	/* Global Control Register				*/
+
+
+/* Omit CAN register sets from the defBF534.h (CAN is not in the ADSP-BF52x processor) */
+
+/* Pin Control Registers	(0xFFC03200 - 0xFFC032FF)											*/
+#define PORTF_FER			0xFFC03200	/* Port F Function Enable Register (Alternate/Flag*)	*/
+#define PORTG_FER			0xFFC03204	/* Port G Function Enable Register (Alternate/Flag*)	*/
+#define PORTH_FER			0xFFC03208	/* Port H Function Enable Register (Alternate/Flag*)	*/
+#define BFIN_PORT_MUX			0xFFC0320C	/* Port Multiplexer Control Register					*/
+
+
+/* Handshake MDMA Registers	(0xFFC03300 - 0xFFC033FF)										*/
+#define HMDMA0_CONTROL		0xFFC03300	/* Handshake MDMA0 Control Register					*/
+#define HMDMA0_ECINIT		0xFFC03304	/* HMDMA0 Initial Edge Count Register				*/
+#define HMDMA0_BCINIT		0xFFC03308	/* HMDMA0 Initial Block Count Register				*/
+#define HMDMA0_ECURGENT		0xFFC0330C	/* HMDMA0 Urgent Edge Count Threshhold Register		*/
+#define HMDMA0_ECOVERFLOW	0xFFC03310	/* HMDMA0 Edge Count Overflow Interrupt Register	*/
+#define HMDMA0_ECOUNT		0xFFC03314	/* HMDMA0 Current Edge Count Register				*/
+#define HMDMA0_BCOUNT		0xFFC03318	/* HMDMA0 Current Block Count Register				*/
+
+#define HMDMA1_CONTROL		0xFFC03340	/* Handshake MDMA1 Control Register					*/
+#define HMDMA1_ECINIT		0xFFC03344	/* HMDMA1 Initial Edge Count Register				*/
+#define HMDMA1_BCINIT		0xFFC03348	/* HMDMA1 Initial Block Count Register				*/
+#define HMDMA1_ECURGENT		0xFFC0334C	/* HMDMA1 Urgent Edge Count Threshhold Register		*/
+#define HMDMA1_ECOVERFLOW	0xFFC03350	/* HMDMA1 Edge Count Overflow Interrupt Register	*/
+#define HMDMA1_ECOUNT		0xFFC03354	/* HMDMA1 Current Edge Count Register				*/
+#define HMDMA1_BCOUNT		0xFFC03358	/* HMDMA1 Current Block Count Register				*/
+
+/* GPIO PIN mux (0xFFC03210 - OxFFC03288) */
+#define PORTF_MUX               0xFFC03210      /* Port F mux control */
+#define PORTG_MUX               0xFFC03214      /* Port G mux control */
+#define PORTH_MUX               0xFFC03218      /* Port H mux control */
+#define PORTF_DRIVE             0xFFC03220      /* Port F drive strength control */
+#define PORTG_DRIVE             0xFFC03224      /* Port G drive strength control */
+#define PORTH_DRIVE             0xFFC03228      /* Port H drive strength control */
+#define PORTF_SLEW              0xFFC03230      /* Port F slew control */
+#define PORTG_SLEW              0xFFC03234      /* Port G slew control */
+#define PORTH_SLEW              0xFFC03238      /* Port H slew control */
+#define PORTF_HYSTERISIS        0xFFC03240      /* Port F Schmitt trigger control */
+#define PORTG_HYSTERISIS        0xFFC03244      /* Port G Schmitt trigger control */
+#define PORTH_HYSTERISIS        0xFFC03248      /* Port H Schmitt trigger control */
+#define MISCPORT_DRIVE          0xFFC03280      /* Misc Port drive strength control */
+#define MISCPORT_SLEW           0xFFC03284      /* Misc Port slew control */
+#define MISCPORT_HYSTERISIS     0xFFC03288      /* Misc Port Schmitt trigger control */
+
+
+/***********************************************************************************
+** System MMR Register Bits And Macros
+**
+** Disclaimer:	All macros are intended to make C and Assembly code more readable.
+**				Use these macros carefully, as any that do left shifts for field
+**				depositing will result in the lower order bits being destroyed.  Any
+**				macro that shifts left to properly position the bit-field should be
+**				used as part of an OR to initialize a register and NOT as a dynamic
+**				modifier UNLESS the lower order bits are saved and ORed back in when
+**				the macro is used.
+*************************************************************************************/
+/*
+** ********************* PLL AND RESET MASKS ****************************************/
+/* PLL_CTL Masks																	*/
+#define DF				0x0001	/* 0: PLL = CLKIN, 1: PLL = CLKIN/2					*/
+#define PLL_OFF			0x0002	/* PLL Not Powered									*/
+#define STOPCK			0x0008	/* Core Clock Off									*/
+#define PDWN			0x0020	/* Enter Deep Sleep Mode							*/
+#define	IN_DELAY		0x0040	/* Add 200ps Delay To EBIU Input Latches			*/
+#define	OUT_DELAY		0x0080	/* Add 200ps Delay To EBIU Output Signals			*/
+#define BYPASS			0x0100	/* Bypass the PLL									*/
+#define	MSEL			0x7E00	/* Multiplier Select For CCLK/VCO Factors			*/
+/* PLL_CTL Macros (Only Use With Logic OR While Setting Lower Order Bits)			*/
+#define	SET_MSEL(x)		(((x)&0x3F) << 0x9)	/* Set MSEL = 0-63 --> VCO = CLKIN*MSEL		*/
+
+/* PLL_DIV Masks														*/
+#define SSEL			0x000F	/* System Select						*/
+#define	CSEL			0x0030	/* Core Select							*/
+#define CSEL_DIV1		0x0000	/* 		CCLK = VCO / 1					*/
+#define CSEL_DIV2		0x0010	/* 		CCLK = VCO / 2					*/
+#define	CSEL_DIV4		0x0020	/* 		CCLK = VCO / 4					*/
+#define	CSEL_DIV8		0x0030	/* 		CCLK = VCO / 8					*/
+/* PLL_DIV Macros														*/
+#define SET_SSEL(x)		((x)&0xF)		/* Set SSEL = 0-15 --> SCLK = VCO/SSEL	*/
+
+/* VR_CTL Masks																	*/
+#define	FREQ			0x0003	/* Switching Oscillator Frequency For Regulator	*/
+#define	HIBERNATE		0x0000	/* 		Powerdown/Bypass On-Board Regulation	*/
+#define	FREQ_333		0x0001	/* 		Switching Frequency Is 333 kHz			*/
+#define	FREQ_667		0x0002	/* 		Switching Frequency Is 667 kHz			*/
+#define	FREQ_1000		0x0003	/* 		Switching Frequency Is 1 MHz			*/
+
+#define GAIN			0x000C	/* Voltage Level Gain	*/
+#define	GAIN_5			0x0000	/* 		GAIN = 5		*/
+#define	GAIN_10			0x0004	/* 		GAIN = 10		*/
+#define	GAIN_20			0x0008	/* 		GAIN = 20		*/
+#define	GAIN_50			0x000C	/* 		GAIN = 50		*/
+
+#define	VLEV			0x00F0	/* Internal Voltage Level					*/
+#define	VLEV_085 		0x0060	/* 		VLEV = 0.85 V (-5% - +10% Accuracy)	*/
+#define	VLEV_090		0x0070	/* 		VLEV = 0.90 V (-5% - +10% Accuracy)	*/
+#define	VLEV_095		0x0080	/* 		VLEV = 0.95 V (-5% - +10% Accuracy)	*/
+#define	VLEV_100		0x0090	/* 		VLEV = 1.00 V (-5% - +10% Accuracy)	*/
+#define	VLEV_105		0x00A0	/* 		VLEV = 1.05 V (-5% - +10% Accuracy)	*/
+#define	VLEV_110		0x00B0	/* 		VLEV = 1.10 V (-5% - +10% Accuracy)	*/
+#define	VLEV_115		0x00C0	/* 		VLEV = 1.15 V (-5% - +10% Accuracy)	*/
+#define	VLEV_120		0x00D0	/* 		VLEV = 1.20 V (-5% - +10% Accuracy)	*/
+#define	VLEV_125		0x00E0	/* 		VLEV = 1.25 V (-5% - +10% Accuracy)	*/
+#define	VLEV_130		0x00F0	/* 		VLEV = 1.30 V (-5% - +10% Accuracy)	*/
+
+#define	WAKE			0x0100	/* Enable RTC/Reset Wakeup From Hibernate	*/
+#define	CANWE			0x0200	/* Enable CAN Wakeup From Hibernate			*/
+#define	PHYWE			0x0400	/* Enable PHY Wakeup From Hibernate			*/
+#define	CLKBUFOE		0x4000	/* CLKIN Buffer Output Enable */
+#define	PHYCLKOE		CLKBUFOE	/* Alternative legacy name for the above */
+#define	SCKELOW		0x8000	/* Enable Drive CKE Low During Reset		*/
+
+/* PLL_STAT Masks																	*/
+#define ACTIVE_PLLENABLED	0x0001	/* Processor In Active Mode With PLL Enabled	*/
+#define	FULL_ON				0x0002	/* Processor In Full On Mode					*/
+#define ACTIVE_PLLDISABLED	0x0004	/* Processor In Active Mode With PLL Disabled	*/
+#define	PLL_LOCKED			0x0020	/* PLL_LOCKCNT Has Been Reached					*/
+
+/* CHIPID Masks */
+#define CHIPID_VERSION         0xF0000000
+#define CHIPID_FAMILY          0x0FFFF000
+#define CHIPID_MANUFACTURE     0x00000FFE
+
+/* SWRST Masks																		*/
+#define SYSTEM_RESET		0x0007	/* Initiates A System Software Reset			*/
+#define	DOUBLE_FAULT		0x0008	/* Core Double Fault Causes Reset				*/
+#define RESET_DOUBLE		0x2000	/* SW Reset Generated By Core Double-Fault		*/
+#define RESET_WDOG			0x4000	/* SW Reset Generated By Watchdog Timer			*/
+#define RESET_SOFTWARE		0x8000	/* SW Reset Occurred Since Last Read Of SWRST	*/
+
+/* SYSCR Masks																				*/
+#define BMODE				0x0007	/* Boot Mode - Latched During HW Reset From Mode Pins	*/
+#define	NOBOOT				0x0010	/* Execute From L1 or ASYNC Bank 0 When BMODE = 0		*/
+
+
+/* *************  SYSTEM INTERRUPT CONTROLLER MASKS *************************************/
+/* Peripheral Masks For SIC_ISR, SIC_IWR, SIC_IMASK										*/
+
+#if 0
+#define IRQ_PLL_WAKEUP	0x00000001	/* PLL Wakeup Interrupt			 					*/
+
+#define IRQ_ERROR1      0x00000002  /* Error Interrupt (DMA, DMARx Block, DMARx Overflow) */
+#define IRQ_ERROR2      0x00000004  /* Error Interrupt (CAN, Ethernet, SPORTx, PPI, SPI, UARTx) */
+#define IRQ_RTC			0x00000008	/* Real Time Clock Interrupt 						*/ 
+#define IRQ_DMA0		0x00000010	/* DMA Channel 0 (PPI) Interrupt 					*/ 
+#define IRQ_DMA3		0x00000020	/* DMA Channel 3 (SPORT0 RX) Interrupt 				*/ 
+#define IRQ_DMA4		0x00000040	/* DMA Channel 4 (SPORT0 TX) Interrupt 				*/
+#define IRQ_DMA5		0x00000080	/* DMA Channel 5 (SPORT1 RX) Interrupt 				*/
+
+#define IRQ_DMA6		0x00000100	/* DMA Channel 6 (SPORT1 TX) Interrupt 		 		*/
+#define IRQ_TWI			0x00000200	/* TWI Interrupt									*/
+#define IRQ_DMA7		0x00000400	/* DMA Channel 7 (SPI) Interrupt 					*/
+#define IRQ_DMA8		0x00000800	/* DMA Channel 8 (UART0 RX) Interrupt 				*/ 
+#define IRQ_DMA9		0x00001000	/* DMA Channel 9 (UART0 TX) Interrupt 				*/
+#define IRQ_DMA10		0x00002000	/* DMA Channel 10 (UART1 RX) Interrupt 				*/
+#define IRQ_DMA11		0x00004000	/* DMA Channel 11 (UART1 TX) Interrupt 				*/
+#define IRQ_CAN_RX		0x00008000	/* CAN Receive Interrupt 							*/
+
+#define IRQ_CAN_TX		0x00010000	/* CAN Transmit Interrupt  							*/
+#define IRQ_DMA1		0x00020000	/* DMA Channel 1 (Ethernet RX) Interrupt 			*/
+#define IRQ_PFA_PORTH	0x00020000	/* PF Port H (PF47:32) Interrupt A 					*/
+#define IRQ_DMA2		0x00040000	/* DMA Channel 2 (Ethernet TX) Interrupt 			*/
+#define IRQ_PFB_PORTH	0x00040000	/* PF Port H (PF47:32) Interrupt B 					*/
+#define IRQ_TIMER0		0x00080000	/* Timer 0 Interrupt								*/
+#define IRQ_TIMER1		0x00100000	/* Timer 1 Interrupt 								*/
+#define IRQ_TIMER2		0x00200000	/* Timer 2 Interrupt 								*/
+#define IRQ_TIMER3		0x00400000	/* Timer 3 Interrupt 								*/
+#define IRQ_TIMER4		0x00800000	/* Timer 4 Interrupt 								*/
+
+#define IRQ_TIMER5		0x01000000	/* Timer 5 Interrupt 								*/
+#define IRQ_TIMER6		0x02000000	/* Timer 6 Interrupt 								*/
+#define IRQ_TIMER7		0x04000000	/* Timer 7 Interrupt 								*/
+#define IRQ_PFA_PORTFG	0x08000000	/* PF Ports F&G (PF31:0) Interrupt A 				*/
+#define IRQ_PFB_PORTF	0x80000000	/* PF Port F (PF15:0) Interrupt B 					*/
+#define IRQ_DMA12		0x20000000	/* DMA Channels 12 (MDMA1 Source) RX Interrupt 		*/
+#define IRQ_DMA13		0x20000000	/* DMA Channels 13 (MDMA1 Destination) TX Interrupt */
+#define IRQ_DMA14		0x40000000	/* DMA Channels 14 (MDMA0 Source) RX Interrupt 		*/
+#define IRQ_DMA15		0x40000000	/* DMA Channels 15 (MDMA0 Destination) TX Interrupt */
+#define IRQ_WDOG		0x80000000	/* Software Watchdog Timer Interrupt 				*/
+#define IRQ_PFB_PORTG	0x10000000	/* PF Port G (PF31:16) Interrupt B 					*/
+#endif
+
+/* SIC_IAR0 Macros															*/
+#define P0_IVG(x)		(((x)&0xF)-7)			/* Peripheral #0 assigned IVG #x 	*/
+#define P1_IVG(x)		(((x)&0xF)-7) << 0x4	/* Peripheral #1 assigned IVG #x 	*/
+#define P2_IVG(x)		(((x)&0xF)-7) << 0x8	/* Peripheral #2 assigned IVG #x 	*/
+#define P3_IVG(x)		(((x)&0xF)-7) << 0xC	/* Peripheral #3 assigned IVG #x	*/
+#define P4_IVG(x)		(((x)&0xF)-7) << 0x10	/* Peripheral #4 assigned IVG #x	*/
+#define P5_IVG(x)		(((x)&0xF)-7) << 0x14	/* Peripheral #5 assigned IVG #x	*/
+#define P6_IVG(x)		(((x)&0xF)-7) << 0x18	/* Peripheral #6 assigned IVG #x	*/
+#define P7_IVG(x)		(((x)&0xF)-7) << 0x1C	/* Peripheral #7 assigned IVG #x	*/
+
+/* SIC_IAR1 Macros															*/
+#define P8_IVG(x)		(((x)&0xF)-7)			/* Peripheral #8 assigned IVG #x 	*/
+#define P9_IVG(x)		(((x)&0xF)-7) << 0x4	/* Peripheral #9 assigned IVG #x 	*/
+#define P10_IVG(x)		(((x)&0xF)-7) << 0x8	/* Peripheral #10 assigned IVG #x	*/
+#define P11_IVG(x)		(((x)&0xF)-7) << 0xC	/* Peripheral #11 assigned IVG #x 	*/
+#define P12_IVG(x)		(((x)&0xF)-7) << 0x10	/* Peripheral #12 assigned IVG #x	*/
+#define P13_IVG(x)		(((x)&0xF)-7) << 0x14	/* Peripheral #13 assigned IVG #x	*/
+#define P14_IVG(x)		(((x)&0xF)-7) << 0x18	/* Peripheral #14 assigned IVG #x	*/
+#define P15_IVG(x)		(((x)&0xF)-7) << 0x1C	/* Peripheral #15 assigned IVG #x	*/
+
+/* SIC_IAR2 Macros															*/
+#define P16_IVG(x)		(((x)&0xF)-7)			/* Peripheral #16 assigned IVG #x	*/
+#define P17_IVG(x)		(((x)&0xF)-7) << 0x4	/* Peripheral #17 assigned IVG #x	*/
+#define P18_IVG(x)		(((x)&0xF)-7) << 0x8	/* Peripheral #18 assigned IVG #x	*/
+#define P19_IVG(x)		(((x)&0xF)-7) << 0xC	/* Peripheral #19 assigned IVG #x	*/
+#define P20_IVG(x)		(((x)&0xF)-7) << 0x10	/* Peripheral #20 assigned IVG #x	*/
+#define P21_IVG(x)		(((x)&0xF)-7) << 0x14	/* Peripheral #21 assigned IVG #x	*/
+#define P22_IVG(x)		(((x)&0xF)-7) << 0x18	/* Peripheral #22 assigned IVG #x	*/
+#define P23_IVG(x)		(((x)&0xF)-7) << 0x1C	/* Peripheral #23 assigned IVG #x	*/
+
+/* SIC_IAR3 Macros															*/
+#define P24_IVG(x)		(((x)&0xF)-7)			/* Peripheral #24 assigned IVG #x	*/
+#define P25_IVG(x)		(((x)&0xF)-7) << 0x4	/* Peripheral #25 assigned IVG #x	*/
+#define P26_IVG(x)		(((x)&0xF)-7) << 0x8	/* Peripheral #26 assigned IVG #x	*/
+#define P27_IVG(x)		(((x)&0xF)-7) << 0xC	/* Peripheral #27 assigned IVG #x	*/
+#define P28_IVG(x)		(((x)&0xF)-7) << 0x10	/* Peripheral #28 assigned IVG #x	*/
+#define P29_IVG(x)		(((x)&0xF)-7) << 0x14	/* Peripheral #29 assigned IVG #x	*/
+#define P30_IVG(x)		(((x)&0xF)-7) << 0x18	/* Peripheral #30 assigned IVG #x	*/
+#define P31_IVG(x)		(((x)&0xF)-7) << 0x1C	/* Peripheral #31 assigned IVG #x	*/
+
+
+/* SIC_IMASK Masks																		*/
+#define SIC_UNMASK_ALL	0x00000000					/* Unmask all peripheral interrupts	*/
+#define SIC_MASK_ALL	0xFFFFFFFF					/* Mask all peripheral interrupts	*/
+#define SIC_MASK(x)		(1 << ((x)&0x1F))					/* Mask Peripheral #x interrupt		*/
+#define SIC_UNMASK(x)	(0xFFFFFFFF ^ (1 << ((x)&0x1F)))	/* Unmask Peripheral #x interrupt	*/
+
+/* SIC_IWR Masks																		*/
+#define IWR_DISABLE_ALL	0x00000000					/* Wakeup Disable all peripherals	*/
+#define IWR_ENABLE_ALL	0xFFFFFFFF					/* Wakeup Enable all peripherals	*/
+#define IWR_ENABLE(x)	(1 << ((x)&0x1F))					/* Wakeup Enable Peripheral #x		*/
+#define IWR_DISABLE(x)	(0xFFFFFFFF ^ (1 << ((x)&0x1F))) 	/* Wakeup Disable Peripheral #x		*/
+
+
+/* ********* WATCHDOG TIMER MASKS ******************** */
+
+/* Watchdog Timer WDOG_CTL Register Masks */
+
+#define WDEV(x) (((x)<<1) & 0x0006) /* event generated on roll over */
+#define WDEV_RESET 0x0000 /* generate reset event on roll over */
+#define WDEV_NMI 0x0002 /* generate NMI event on roll over */
+#define WDEV_GPI 0x0004 /* generate GP IRQ on roll over */
+#define WDEV_NONE 0x0006 /* no event on roll over */
+#define WDEN 0x0FF0 /* enable watchdog */
+#define WDDIS 0x0AD0 /* disable watchdog */
+#define WDRO 0x8000 /* watchdog rolled over latch */ 
+
+/* depreciated WDOG_CTL Register Masks for legacy code */
+
+
+#define ICTL WDEV
+#define ENABLE_RESET WDEV_RESET
+#define WDOG_RESET WDEV_RESET
+#define ENABLE_NMI WDEV_NMI
+#define WDOG_NMI WDEV_NMI
+#define ENABLE_GPI WDEV_GPI
+#define WDOG_GPI WDEV_GPI
+#define DISABLE_EVT WDEV_NONE
+#define WDOG_NONE WDEV_NONE
+
+#define TMR_EN WDEN
+#define TMR_DIS WDDIS
+#define TRO WDRO
+#define ICTL_P0 0x01
+ #define ICTL_P1 0x02
+#define TRO_P 0x0F
+
+
+
+/* ***************  REAL TIME CLOCK MASKS  **************************/
+/* RTC_STAT and RTC_ALARM Masks										*/
+#define	RTC_SEC				0x0000003F	/* Real-Time Clock Seconds	*/
+#define	RTC_MIN				0x00000FC0	/* Real-Time Clock Minutes	*/
+#define	RTC_HR				0x0001F000	/* Real-Time Clock Hours	*/
+#define	RTC_DAY				0xFFFE0000	/* Real-Time Clock Days		*/
+
+/* RTC_ALARM Macro			z=day		y=hr	x=min	w=sec		*/
+#define SET_ALARM(z,y,x,w)	((((z)&0x7FFF)<<0x11)|(((y)&0x1F)<<0xC)|(((x)&0x3F)<<0x6)|((w)&0x3F))
+
+/* RTC_ICTL and RTC_ISTAT Masks																		*/
+#define	STOPWATCH			0x0001		/* Stopwatch Interrupt Enable								*/
+#define	ALARM				0x0002		/* Alarm Interrupt Enable									*/
+#define	SECOND				0x0004		/* Seconds (1 Hz) Interrupt Enable							*/
+#define	MINUTE				0x0008		/* Minutes Interrupt Enable									*/
+#define	HOUR				0x0010		/* Hours Interrupt Enable									*/
+#define	DAY					0x0020		/* 24 Hours (Days) Interrupt Enable							*/
+#define	DAY_ALARM			0x0040		/* Day Alarm (Day, Hour, Minute, Second) Interrupt Enable	*/
+#define	WRITE_PENDING		0x4000		/* Write Pending Status										*/
+#define	WRITE_COMPLETE		0x8000		/* Write Complete Interrupt Enable							*/
+
+/* RTC_FAST / RTC_PREN Mask												*/
+#define PREN				0x0001	/* Enable Prescaler, RTC Runs @1 Hz	*/
+
+
+/* ************** UART CONTROLLER MASKS *************************/
+/* UARTx_LCR Masks												*/
+#define WLS(x)		(((x)-5) & 0x03)	/* Word Length Select */
+#define STB			0x04				/* Stop Bits			*/
+#define PEN			0x08				/* Parity Enable		*/
+#define EPS			0x10				/* Even Parity Select	*/
+#define STP			0x20				/* Stick Parity			*/
+#define SB			0x40				/* Set Break			*/
+#define DLAB		0x80				/* Divisor Latch Access	*/
+
+/* UARTx_MCR Mask										*/
+#define LOOP_ENA	0x10	/* Loopback Mode Enable */
+#define LOOP_ENA_P	0x04
+
+/* UARTx_LSR Masks										*/
+#define DR			0x01	/* Data Ready				*/
+#define OE			0x02	/* Overrun Error			*/
+#define PE			0x04	/* Parity Error				*/
+#define FE			0x08	/* Framing Error			*/
+#define BI			0x10	/* Break Interrupt			*/
+#define THRE		0x20	/* THR Empty				*/
+#define TEMT		0x40	/* TSR and UART_THR Empty	*/
+
+/* UARTx_IER Masks															*/
+#define ERBFI		0x01		/* Enable Receive Buffer Full Interrupt		*/
+#define ETBEI		0x02		/* Enable Transmit Buffer Empty Interrupt	*/
+#define ELSI		0x04		/* Enable RX Status Interrupt				*/
+
+/* UARTx_IIR Masks														*/
+#define NINT		0x01		/* Pending Interrupt					*/
+#define IIR_TX_READY    0x02		/* UART_THR empty                               */
+#define IIR_RX_READY    0x04		/* Receive data ready                           */
+#define IIR_LINE_CHANGE 0x06		/* Receive line status    			*/ 
+#define IIR_STATUS	0x06		/* Highest Priority Pending Interrupt	*/
+
+/* UARTx_GCTL Masks													*/
+#define UCEN		0x01		/* Enable UARTx Clocks				*/
+#define IREN		0x02		/* Enable IrDA Mode					*/
+#define TPOLC		0x04		/* IrDA TX Polarity Change			*/
+#define RPOLC		0x08		/* IrDA RX Polarity Change			*/
+#define FPE			0x10		/* Force Parity Error On Transmit	*/
+#define FFE			0x20		/* Force Framing Error On Transmit	*/
+
+
+/* ***********  SERIAL PERIPHERAL INTERFACE (SPI) MASKS  ****************************/
+/* SPI_CTL Masks																	*/
+#define	TIMOD		0x0003		/* Transfer Initiate Mode							*/
+#define RDBR_CORE	0x0000		/* 		RDBR Read Initiates, IRQ When RDBR Full		*/
+#define	TDBR_CORE	0x0001		/* 		TDBR Write Initiates, IRQ When TDBR Empty	*/
+#define RDBR_DMA	0x0002		/* 		DMA Read, DMA Until FIFO Empty				*/
+#define TDBR_DMA	0x0003		/* 		DMA Write, DMA Until FIFO Full				*/
+#define SZ			0x0004		/* Send Zero (When TDBR Empty, Send Zero/Last*)		*/
+#define GM			0x0008		/* Get More (When RDBR Full, Overwrite/Discard*)	*/
+#define PSSE		0x0010		/* Slave-Select Input Enable						*/
+#define EMISO		0x0020		/* Enable MISO As Output							*/
+#define SIZE		0x0100		/* Size of Words (16/8* Bits)						*/
+#define LSBF		0x0200		/* LSB First										*/
+#define CPHA		0x0400		/* Clock Phase										*/
+#define CPOL		0x0800		/* Clock Polarity									*/
+#define MSTR		0x1000		/* Master/Slave*									*/
+#define WOM			0x2000		/* Write Open Drain Master							*/
+#define SPE			0x4000		/* SPI Enable										*/
+
+/* SPI_FLG Masks																	*/
+#define FLS1		0x0002		/* Enables SPI_FLOUT1 as SPI Slave-Select Output	*/
+#define FLS2		0x0004		/* Enables SPI_FLOUT2 as SPI Slave-Select Output	*/
+#define FLS3		0x0008		/* Enables SPI_FLOUT3 as SPI Slave-Select Output	*/
+#define FLS4		0x0010		/* Enables SPI_FLOUT4 as SPI Slave-Select Output	*/
+#define FLS5		0x0020		/* Enables SPI_FLOUT5 as SPI Slave-Select Output	*/
+#define FLS6		0x0040		/* Enables SPI_FLOUT6 as SPI Slave-Select Output	*/
+#define FLS7		0x0080		/* Enables SPI_FLOUT7 as SPI Slave-Select Output	*/
+#define FLG1		0xFDFF		/* Activates SPI_FLOUT1 							*/
+#define FLG2		0xFBFF		/* Activates SPI_FLOUT2								*/
+#define FLG3		0xF7FF		/* Activates SPI_FLOUT3								*/
+#define FLG4		0xEFFF		/* Activates SPI_FLOUT4								*/
+#define FLG5		0xDFFF		/* Activates SPI_FLOUT5								*/
+#define FLG6		0xBFFF		/* Activates SPI_FLOUT6								*/
+#define FLG7		0x7FFF		/* Activates SPI_FLOUT7								*/
+
+/* SPI_STAT Masks																				*/
+#define SPIF		0x0001		/* SPI Finished (Single-Word Transfer Complete)					*/
+#define MODF		0x0002		/* Mode Fault Error (Another Device Tried To Become Master)		*/
+#define TXE			0x0004		/* Transmission Error (Data Sent With No New Data In TDBR)		*/
+#define TXS			0x0008		/* SPI_TDBR Data Buffer Status (Full/Empty*)					*/
+#define RBSY		0x0010		/* Receive Error (Data Received With RDBR Full)					*/
+#define RXS			0x0020		/* SPI_RDBR Data Buffer Status (Full/Empty*)					*/
+#define TXCOL		0x0040		/* Transmit Collision Error (Corrupt Data May Have Been Sent)	*/
+
+
+/*  ****************  GENERAL PURPOSE TIMER MASKS  **********************/
+/* TIMER_ENABLE Masks													*/
+#define TIMEN0			0x0001		/* Enable Timer 0					*/
+#define TIMEN1			0x0002		/* Enable Timer 1					*/
+#define TIMEN2			0x0004		/* Enable Timer 2					*/
+#define TIMEN3			0x0008		/* Enable Timer 3					*/
+#define TIMEN4			0x0010		/* Enable Timer 4					*/
+#define TIMEN5			0x0020		/* Enable Timer 5					*/
+#define TIMEN6			0x0040		/* Enable Timer 6					*/
+#define TIMEN7			0x0080		/* Enable Timer 7					*/
+
+/* TIMER_DISABLE Masks													*/
+#define TIMDIS0			TIMEN0		/* Disable Timer 0					*/
+#define TIMDIS1			TIMEN1		/* Disable Timer 1					*/
+#define TIMDIS2			TIMEN2		/* Disable Timer 2					*/
+#define TIMDIS3			TIMEN3		/* Disable Timer 3					*/
+#define TIMDIS4			TIMEN4		/* Disable Timer 4					*/
+#define TIMDIS5			TIMEN5		/* Disable Timer 5					*/
+#define TIMDIS6			TIMEN6		/* Disable Timer 6					*/
+#define TIMDIS7			TIMEN7		/* Disable Timer 7					*/
+
+/* TIMER_STATUS Masks													*/
+#define TIMIL0			0x00000001	/* Timer 0 Interrupt				*/
+#define TIMIL1			0x00000002	/* Timer 1 Interrupt				*/
+#define TIMIL2			0x00000004	/* Timer 2 Interrupt				*/
+#define TIMIL3			0x00000008	/* Timer 3 Interrupt				*/
+#define TOVF_ERR0		0x00000010	/* Timer 0 Counter Overflow			*/
+#define TOVF_ERR1		0x00000020	/* Timer 1 Counter Overflow			*/
+#define TOVF_ERR2		0x00000040	/* Timer 2 Counter Overflow			*/
+#define TOVF_ERR3		0x00000080	/* Timer 3 Counter Overflow			*/
+#define TRUN0			0x00001000	/* Timer 0 Slave Enable Status		*/
+#define TRUN1			0x00002000	/* Timer 1 Slave Enable Status		*/
+#define TRUN2			0x00004000	/* Timer 2 Slave Enable Status		*/
+#define TRUN3			0x00008000	/* Timer 3 Slave Enable Status		*/
+#define TIMIL4			0x00010000	/* Timer 4 Interrupt				*/
+#define TIMIL5			0x00020000	/* Timer 5 Interrupt				*/
+#define TIMIL6			0x00040000	/* Timer 6 Interrupt				*/
+#define TIMIL7			0x00080000	/* Timer 7 Interrupt				*/
+#define TOVF_ERR4		0x00100000	/* Timer 4 Counter Overflow			*/
+#define TOVF_ERR5		0x00200000	/* Timer 5 Counter Overflow			*/
+#define TOVF_ERR6		0x00400000	/* Timer 6 Counter Overflow			*/
+#define TOVF_ERR7		0x00800000	/* Timer 7 Counter Overflow			*/
+#define TRUN4			0x10000000	/* Timer 4 Slave Enable Status		*/
+#define TRUN5			0x20000000	/* Timer 5 Slave Enable Status		*/
+#define TRUN6			0x40000000	/* Timer 6 Slave Enable Status		*/
+#define TRUN7			0x80000000	/* Timer 7 Slave Enable Status		*/
+
+/* Alternate Deprecated Macros Provided For Backwards Code Compatibility */
+#define TOVL_ERR0 TOVF_ERR0
+#define TOVL_ERR1 TOVF_ERR1
+#define TOVL_ERR2 TOVF_ERR2
+#define TOVL_ERR3 TOVF_ERR3
+#define TOVL_ERR4 TOVF_ERR4
+#define TOVL_ERR5 TOVF_ERR5
+#define TOVL_ERR6 TOVF_ERR6
+#define TOVL_ERR7 TOVF_ERR7
+
+/* TIMERx_CONFIG Masks													*/
+#define PWM_OUT			0x0001	/* Pulse-Width Modulation Output Mode	*/
+#define WDTH_CAP		0x0002	/* Width Capture Input Mode				*/
+#define EXT_CLK			0x0003	/* External Clock Mode					*/
+#define PULSE_HI		0x0004	/* Action Pulse (Positive/Negative*)	*/
+#define PERIOD_CNT		0x0008	/* Period Count							*/
+#define IRQ_ENA			0x0010	/* Interrupt Request Enable				*/
+#define TIN_SEL			0x0020	/* Timer Input Select					*/
+#define OUT_DIS			0x0040	/* Output Pad Disable					*/
+#define CLK_SEL			0x0080	/* Timer Clock Select					*/
+#define TOGGLE_HI		0x0100	/* PWM_OUT PULSE_HI Toggle Mode			*/
+#define EMU_RUN			0x0200	/* Emulation Behavior Select			*/
+#define ERR_TYP			0xC000	/* Error Type							*/
+
+
+/* ******************   GPIO PORTS F, G, H MASKS  ***********************/
+/*  General Purpose IO (0xFFC00700 - 0xFFC007FF)  Masks 				*/
+/* Port F Masks 														*/
+#define PF0		0x0001
+#define PF1		0x0002
+#define PF2		0x0004
+#define PF3		0x0008
+#define PF4		0x0010
+#define PF5		0x0020
+#define PF6		0x0040
+#define PF7		0x0080
+#define PF8		0x0100
+#define PF9		0x0200
+#define PF10	0x0400
+#define PF11	0x0800
+#define PF12	0x1000
+#define PF13	0x2000
+#define PF14	0x4000
+#define PF15	0x8000
+
+/* Port G Masks															*/
+#define PG0		0x0001
+#define PG1		0x0002
+#define PG2		0x0004
+#define PG3		0x0008
+#define PG4		0x0010
+#define PG5		0x0020
+#define PG6		0x0040
+#define PG7		0x0080
+#define PG8		0x0100
+#define PG9		0x0200
+#define PG10	0x0400
+#define PG11	0x0800
+#define PG12	0x1000
+#define PG13	0x2000
+#define PG14	0x4000
+#define PG15	0x8000
+
+/* Port H Masks															*/
+#define PH0		0x0001
+#define PH1		0x0002
+#define PH2		0x0004
+#define PH3		0x0008
+#define PH4		0x0010
+#define PH5		0x0020
+#define PH6		0x0040
+#define PH7		0x0080
+#define PH8		0x0100
+#define PH9		0x0200
+#define PH10	0x0400
+#define PH11	0x0800
+#define PH12	0x1000
+#define PH13	0x2000
+#define PH14	0x4000
+#define PH15	0x8000
+
+
+/* *******************  SERIAL PORT MASKS  **************************************/
+/* SPORTx_TCR1 Masks															*/
+#define TSPEN		0x0001		/* Transmit Enable								*/
+#define ITCLK		0x0002		/* Internal Transmit Clock Select				*/
+#define DTYPE_NORM	0x0004		/* Data Format Normal							*/
+#define DTYPE_ULAW	0x0008		/* Compand Using u-Law							*/
+#define DTYPE_ALAW	0x000C		/* Compand Using A-Law							*/
+#define TLSBIT		0x0010		/* Transmit Bit Order							*/
+#define ITFS		0x0200		/* Internal Transmit Frame Sync Select			*/
+#define TFSR		0x0400		/* Transmit Frame Sync Required Select			*/
+#define DITFS		0x0800		/* Data-Independent Transmit Frame Sync Select	*/
+#define LTFS		0x1000		/* Low Transmit Frame Sync Select				*/
+#define LATFS		0x2000		/* Late Transmit Frame Sync Select				*/
+#define TCKFE		0x4000		/* Clock Falling Edge Select					*/
+
+/* SPORTx_TCR2 Masks and Macro													*/
+#define SLEN(x)		((x)&0x1F)	/* SPORT TX Word Length (2 - 31)				*/
+#define TXSE		0x0100		/* TX Secondary Enable							*/
+#define TSFSE		0x0200		/* Transmit Stereo Frame Sync Enable			*/
+#define TRFST		0x0400		/* Left/Right Order (1 = Right Channel 1st)		*/
+
+/* SPORTx_RCR1 Masks															*/
+#define RSPEN		0x0001		/* Receive Enable 								*/
+#define IRCLK		0x0002		/* Internal Receive Clock Select 				*/
+#define DTYPE_NORM	0x0004		/* Data Format Normal							*/
+#define DTYPE_ULAW	0x0008		/* Compand Using u-Law							*/
+#define DTYPE_ALAW	0x000C		/* Compand Using A-Law							*/
+#define RLSBIT		0x0010		/* Receive Bit Order							*/
+#define IRFS		0x0200		/* Internal Receive Frame Sync Select 			*/
+#define RFSR		0x0400		/* Receive Frame Sync Required Select 			*/
+#define LRFS		0x1000		/* Low Receive Frame Sync Select 				*/
+#define LARFS		0x2000		/* Late Receive Frame Sync Select 				*/
+#define RCKFE		0x4000		/* Clock Falling Edge Select 					*/
+
+/* SPORTx_RCR2 Masks															*/
+#define SLEN(x)		((x)&0x1F)	/* SPORT RX Word Length (2 - 31)				*/
+#define RXSE		0x0100		/* RX Secondary Enable							*/
+#define RSFSE		0x0200		/* RX Stereo Frame Sync Enable					*/
+#define RRFST		0x0400		/* Right-First Data Order 						*/
+
+/* SPORTx_STAT Masks															*/
+#define RXNE		0x0001		/* Receive FIFO Not Empty Status				*/
+#define RUVF		0x0002		/* Sticky Receive Underflow Status				*/
+#define ROVF		0x0004		/* Sticky Receive Overflow Status				*/
+#define TXF			0x0008		/* Transmit FIFO Full Status					*/
+#define TUVF		0x0010		/* Sticky Transmit Underflow Status				*/
+#define TOVF		0x0020		/* Sticky Transmit Overflow Status				*/
+#define TXHRE		0x0040		/* Transmit Hold Register Empty					*/
+
+/* SPORTx_MCMC1 Macros															*/
+#define SP_WOFF(x)	((x) & 0x3FF) 	/* Multichannel Window Offset Field			*/
+
+/* Only use WSIZE Macro With Logic OR While Setting Lower Order Bits						*/
+#define SP_WSIZE(x)	(((((x)>>0x3)-1)&0xF) << 0xC)	/* Multichannel Window Size = (x/8)-1	*/
+
+/* SPORTx_MCMC2 Masks															*/
+#define REC_BYPASS	0x0000		/* Bypass Mode (No Clock Recovery)				*/
+#define REC_2FROM4	0x0002		/* Recover 2 MHz Clock from 4 MHz Clock			*/
+#define REC_8FROM16	0x0003		/* Recover 8 MHz Clock from 16 MHz Clock		*/
+#define MCDTXPE		0x0004 		/* Multichannel DMA Transmit Packing			*/
+#define MCDRXPE		0x0008 		/* Multichannel DMA Receive Packing				*/
+#define MCMEN		0x0010 		/* Multichannel Frame Mode Enable				*/
+#define FSDR		0x0080 		/* Multichannel Frame Sync to Data Relationship	*/
+#define MFD_0		0x0000		/* Multichannel Frame Delay = 0					*/
+#define MFD_1		0x1000		/* Multichannel Frame Delay = 1					*/
+#define MFD_2		0x2000		/* Multichannel Frame Delay = 2					*/
+#define MFD_3		0x3000		/* Multichannel Frame Delay = 3					*/
+#define MFD_4		0x4000		/* Multichannel Frame Delay = 4					*/
+#define MFD_5		0x5000		/* Multichannel Frame Delay = 5					*/
+#define MFD_6		0x6000		/* Multichannel Frame Delay = 6					*/
+#define MFD_7		0x7000		/* Multichannel Frame Delay = 7					*/
+#define MFD_8		0x8000		/* Multichannel Frame Delay = 8					*/
+#define MFD_9		0x9000		/* Multichannel Frame Delay = 9					*/
+#define MFD_10		0xA000		/* Multichannel Frame Delay = 10				*/
+#define MFD_11		0xB000		/* Multichannel Frame Delay = 11				*/
+#define MFD_12		0xC000		/* Multichannel Frame Delay = 12				*/
+#define MFD_13		0xD000		/* Multichannel Frame Delay = 13				*/
+#define MFD_14		0xE000		/* Multichannel Frame Delay = 14				*/
+#define MFD_15		0xF000		/* Multichannel Frame Delay = 15				*/
+
+
+/* *********************  ASYNCHRONOUS MEMORY CONTROLLER MASKS  *************************/
+/* EBIU_AMGCTL Masks																	*/
+#define AMCKEN			0x0001		/* Enable CLKOUT									*/
+#define	AMBEN_NONE		0x0000		/* All Banks Disabled								*/
+#define AMBEN_B0		0x0002		/* Enable Async Memory Bank 0 only					*/
+#define AMBEN_B0_B1		0x0004		/* Enable Async Memory Banks 0 & 1 only				*/
+#define AMBEN_B0_B1_B2	0x0006		/* Enable Async Memory Banks 0, 1, and 2			*/
+#define AMBEN_ALL		0x0008		/* Enable Async Memory Banks (all) 0, 1, 2, and 3	*/
+
+/* EBIU_AMBCTL0 Masks																	*/
+#define B0RDYEN			0x00000001  /* Bank 0 (B0) RDY Enable							*/
+#define B0RDYPOL		0x00000002  /* B0 RDY Active High								*/
+#define B0TT_1			0x00000004  /* B0 Transition Time (Read to Write) = 1 cycle		*/
+#define B0TT_2			0x00000008  /* B0 Transition Time (Read to Write) = 2 cycles	*/
+#define B0TT_3			0x0000000C  /* B0 Transition Time (Read to Write) = 3 cycles	*/
+#define B0TT_4			0x00000000  /* B0 Transition Time (Read to Write) = 4 cycles	*/
+#define B0ST_1			0x00000010  /* B0 Setup Time (AOE to Read/Write) = 1 cycle		*/
+#define B0ST_2			0x00000020  /* B0 Setup Time (AOE to Read/Write) = 2 cycles		*/
+#define B0ST_3			0x00000030  /* B0 Setup Time (AOE to Read/Write) = 3 cycles		*/
+#define B0ST_4			0x00000000  /* B0 Setup Time (AOE to Read/Write) = 4 cycles		*/
+#define B0HT_1			0x00000040  /* B0 Hold Time (~Read/Write to ~AOE) = 1 cycle		*/
+#define B0HT_2			0x00000080  /* B0 Hold Time (~Read/Write to ~AOE) = 2 cycles	*/
+#define B0HT_3			0x000000C0  /* B0 Hold Time (~Read/Write to ~AOE) = 3 cycles	*/
+#define B0HT_0			0x00000000  /* B0 Hold Time (~Read/Write to ~AOE) = 0 cycles	*/
+#define B0RAT_1			0x00000100  /* B0 Read Access Time = 1 cycle					*/
+#define B0RAT_2			0x00000200  /* B0 Read Access Time = 2 cycles					*/
+#define B0RAT_3			0x00000300  /* B0 Read Access Time = 3 cycles					*/
+#define B0RAT_4			0x00000400  /* B0 Read Access Time = 4 cycles					*/
+#define B0RAT_5			0x00000500  /* B0 Read Access Time = 5 cycles					*/
+#define B0RAT_6			0x00000600  /* B0 Read Access Time = 6 cycles					*/
+#define B0RAT_7			0x00000700  /* B0 Read Access Time = 7 cycles					*/
+#define B0RAT_8			0x00000800  /* B0 Read Access Time = 8 cycles					*/
+#define B0RAT_9			0x00000900  /* B0 Read Access Time = 9 cycles					*/
+#define B0RAT_10		0x00000A00  /* B0 Read Access Time = 10 cycles					*/
+#define B0RAT_11		0x00000B00  /* B0 Read Access Time = 11 cycles					*/
+#define B0RAT_12		0x00000C00  /* B0 Read Access Time = 12 cycles					*/
+#define B0RAT_13		0x00000D00  /* B0 Read Access Time = 13 cycles					*/
+#define B0RAT_14		0x00000E00  /* B0 Read Access Time = 14 cycles					*/
+#define B0RAT_15		0x00000F00  /* B0 Read Access Time = 15 cycles					*/
+#define B0WAT_1			0x00001000  /* B0 Write Access Time = 1 cycle					*/
+#define B0WAT_2			0x00002000  /* B0 Write Access Time = 2 cycles					*/
+#define B0WAT_3			0x00003000  /* B0 Write Access Time = 3 cycles					*/
+#define B0WAT_4			0x00004000  /* B0 Write Access Time = 4 cycles					*/
+#define B0WAT_5			0x00005000  /* B0 Write Access Time = 5 cycles					*/
+#define B0WAT_6			0x00006000  /* B0 Write Access Time = 6 cycles					*/
+#define B0WAT_7			0x00007000  /* B0 Write Access Time = 7 cycles					*/
+#define B0WAT_8			0x00008000  /* B0 Write Access Time = 8 cycles					*/
+#define B0WAT_9			0x00009000  /* B0 Write Access Time = 9 cycles					*/
+#define B0WAT_10		0x0000A000  /* B0 Write Access Time = 10 cycles					*/
+#define B0WAT_11		0x0000B000  /* B0 Write Access Time = 11 cycles					*/
+#define B0WAT_12		0x0000C000  /* B0 Write Access Time = 12 cycles					*/
+#define B0WAT_13		0x0000D000  /* B0 Write Access Time = 13 cycles					*/
+#define B0WAT_14		0x0000E000  /* B0 Write Access Time = 14 cycles					*/
+#define B0WAT_15		0x0000F000  /* B0 Write Access Time = 15 cycles					*/
+
+#define B1RDYEN			0x00010000  /* Bank 1 (B1) RDY Enable                       	*/
+#define B1RDYPOL		0x00020000  /* B1 RDY Active High                           	*/
+#define B1TT_1			0x00040000  /* B1 Transition Time (Read to Write) = 1 cycle 	*/
+#define B1TT_2			0x00080000  /* B1 Transition Time (Read to Write) = 2 cycles	*/
+#define B1TT_3			0x000C0000  /* B1 Transition Time (Read to Write) = 3 cycles	*/
+#define B1TT_4			0x00000000  /* B1 Transition Time (Read to Write) = 4 cycles	*/
+#define B1ST_1			0x00100000  /* B1 Setup Time (AOE to Read/Write) = 1 cycle  	*/
+#define B1ST_2			0x00200000  /* B1 Setup Time (AOE to Read/Write) = 2 cycles 	*/
+#define B1ST_3			0x00300000  /* B1 Setup Time (AOE to Read/Write) = 3 cycles 	*/
+#define B1ST_4			0x00000000  /* B1 Setup Time (AOE to Read/Write) = 4 cycles 	*/
+#define B1HT_1			0x00400000  /* B1 Hold Time (~Read/Write to ~AOE) = 1 cycle 	*/
+#define B1HT_2			0x00800000  /* B1 Hold Time (~Read/Write to ~AOE) = 2 cycles	*/
+#define B1HT_3			0x00C00000  /* B1 Hold Time (~Read/Write to ~AOE) = 3 cycles	*/
+#define B1HT_0			0x00000000  /* B1 Hold Time (~Read/Write to ~AOE) = 0 cycles	*/
+#define B1RAT_1			0x01000000  /* B1 Read Access Time = 1 cycle					*/
+#define B1RAT_2			0x02000000  /* B1 Read Access Time = 2 cycles					*/
+#define B1RAT_3			0x03000000  /* B1 Read Access Time = 3 cycles					*/
+#define B1RAT_4			0x04000000  /* B1 Read Access Time = 4 cycles					*/
+#define B1RAT_5			0x05000000  /* B1 Read Access Time = 5 cycles					*/
+#define B1RAT_6			0x06000000  /* B1 Read Access Time = 6 cycles					*/
+#define B1RAT_7			0x07000000  /* B1 Read Access Time = 7 cycles					*/
+#define B1RAT_8			0x08000000  /* B1 Read Access Time = 8 cycles					*/
+#define B1RAT_9			0x09000000  /* B1 Read Access Time = 9 cycles					*/
+#define B1RAT_10		0x0A000000  /* B1 Read Access Time = 10 cycles					*/
+#define B1RAT_11		0x0B000000  /* B1 Read Access Time = 11 cycles					*/
+#define B1RAT_12		0x0C000000  /* B1 Read Access Time = 12 cycles					*/
+#define B1RAT_13		0x0D000000  /* B1 Read Access Time = 13 cycles					*/
+#define B1RAT_14		0x0E000000  /* B1 Read Access Time = 14 cycles					*/
+#define B1RAT_15		0x0F000000  /* B1 Read Access Time = 15 cycles					*/
+#define B1WAT_1			0x10000000  /* B1 Write Access Time = 1 cycle					*/
+#define B1WAT_2			0x20000000  /* B1 Write Access Time = 2 cycles					*/
+#define B1WAT_3			0x30000000  /* B1 Write Access Time = 3 cycles					*/
+#define B1WAT_4			0x40000000  /* B1 Write Access Time = 4 cycles					*/
+#define B1WAT_5			0x50000000  /* B1 Write Access Time = 5 cycles					*/
+#define B1WAT_6			0x60000000  /* B1 Write Access Time = 6 cycles					*/
+#define B1WAT_7			0x70000000  /* B1 Write Access Time = 7 cycles					*/
+#define B1WAT_8			0x80000000  /* B1 Write Access Time = 8 cycles					*/
+#define B1WAT_9			0x90000000  /* B1 Write Access Time = 9 cycles					*/
+#define B1WAT_10		0xA0000000  /* B1 Write Access Time = 10 cycles					*/
+#define B1WAT_11		0xB0000000  /* B1 Write Access Time = 11 cycles					*/
+#define B1WAT_12		0xC0000000  /* B1 Write Access Time = 12 cycles					*/
+#define B1WAT_13		0xD0000000  /* B1 Write Access Time = 13 cycles					*/
+#define B1WAT_14		0xE0000000  /* B1 Write Access Time = 14 cycles					*/
+#define B1WAT_15		0xF0000000  /* B1 Write Access Time = 15 cycles					*/
+
+/* EBIU_AMBCTL1 Masks																	*/
+#define B2RDYEN			0x00000001  /* Bank 2 (B2) RDY Enable							*/
+#define B2RDYPOL		0x00000002  /* B2 RDY Active High								*/
+#define B2TT_1			0x00000004  /* B2 Transition Time (Read to Write) = 1 cycle		*/
+#define B2TT_2			0x00000008  /* B2 Transition Time (Read to Write) = 2 cycles	*/
+#define B2TT_3			0x0000000C  /* B2 Transition Time (Read to Write) = 3 cycles	*/
+#define B2TT_4			0x00000000  /* B2 Transition Time (Read to Write) = 4 cycles	*/
+#define B2ST_1			0x00000010  /* B2 Setup Time (AOE to Read/Write) = 1 cycle		*/
+#define B2ST_2			0x00000020  /* B2 Setup Time (AOE to Read/Write) = 2 cycles		*/
+#define B2ST_3			0x00000030  /* B2 Setup Time (AOE to Read/Write) = 3 cycles		*/
+#define B2ST_4			0x00000000  /* B2 Setup Time (AOE to Read/Write) = 4 cycles		*/
+#define B2HT_1			0x00000040  /* B2 Hold Time (~Read/Write to ~AOE) = 1 cycle		*/
+#define B2HT_2			0x00000080  /* B2 Hold Time (~Read/Write to ~AOE) = 2 cycles	*/
+#define B2HT_3			0x000000C0  /* B2 Hold Time (~Read/Write to ~AOE) = 3 cycles	*/
+#define B2HT_0			0x00000000  /* B2 Hold Time (~Read/Write to ~AOE) = 0 cycles	*/
+#define B2RAT_1			0x00000100  /* B2 Read Access Time = 1 cycle					*/
+#define B2RAT_2			0x00000200  /* B2 Read Access Time = 2 cycles					*/
+#define B2RAT_3			0x00000300  /* B2 Read Access Time = 3 cycles					*/
+#define B2RAT_4			0x00000400  /* B2 Read Access Time = 4 cycles					*/
+#define B2RAT_5			0x00000500  /* B2 Read Access Time = 5 cycles					*/
+#define B2RAT_6			0x00000600  /* B2 Read Access Time = 6 cycles					*/
+#define B2RAT_7			0x00000700  /* B2 Read Access Time = 7 cycles					*/
+#define B2RAT_8			0x00000800  /* B2 Read Access Time = 8 cycles					*/
+#define B2RAT_9			0x00000900  /* B2 Read Access Time = 9 cycles					*/
+#define B2RAT_10		0x00000A00  /* B2 Read Access Time = 10 cycles					*/
+#define B2RAT_11		0x00000B00  /* B2 Read Access Time = 11 cycles					*/
+#define B2RAT_12		0x00000C00  /* B2 Read Access Time = 12 cycles					*/
+#define B2RAT_13		0x00000D00  /* B2 Read Access Time = 13 cycles					*/
+#define B2RAT_14		0x00000E00  /* B2 Read Access Time = 14 cycles					*/
+#define B2RAT_15		0x00000F00  /* B2 Read Access Time = 15 cycles					*/
+#define B2WAT_1			0x00001000  /* B2 Write Access Time = 1 cycle					*/
+#define B2WAT_2			0x00002000  /* B2 Write Access Time = 2 cycles					*/
+#define B2WAT_3			0x00003000  /* B2 Write Access Time = 3 cycles					*/
+#define B2WAT_4			0x00004000  /* B2 Write Access Time = 4 cycles					*/
+#define B2WAT_5			0x00005000  /* B2 Write Access Time = 5 cycles					*/
+#define B2WAT_6			0x00006000  /* B2 Write Access Time = 6 cycles					*/
+#define B2WAT_7			0x00007000  /* B2 Write Access Time = 7 cycles					*/
+#define B2WAT_8			0x00008000  /* B2 Write Access Time = 8 cycles					*/
+#define B2WAT_9			0x00009000  /* B2 Write Access Time = 9 cycles					*/
+#define B2WAT_10		0x0000A000  /* B2 Write Access Time = 10 cycles					*/
+#define B2WAT_11		0x0000B000  /* B2 Write Access Time = 11 cycles					*/
+#define B2WAT_12		0x0000C000  /* B2 Write Access Time = 12 cycles					*/
+#define B2WAT_13		0x0000D000  /* B2 Write Access Time = 13 cycles					*/
+#define B2WAT_14		0x0000E000  /* B2 Write Access Time = 14 cycles					*/
+#define B2WAT_15		0x0000F000  /* B2 Write Access Time = 15 cycles					*/
+
+#define B3RDYEN			0x00010000  /* Bank 3 (B3) RDY Enable							*/
+#define B3RDYPOL		0x00020000  /* B3 RDY Active High								*/
+#define B3TT_1			0x00040000  /* B3 Transition Time (Read to Write) = 1 cycle		*/
+#define B3TT_2			0x00080000  /* B3 Transition Time (Read to Write) = 2 cycles	*/
+#define B3TT_3			0x000C0000  /* B3 Transition Time (Read to Write) = 3 cycles	*/
+#define B3TT_4			0x00000000  /* B3 Transition Time (Read to Write) = 4 cycles	*/
+#define B3ST_1			0x00100000  /* B3 Setup Time (AOE to Read/Write) = 1 cycle		*/
+#define B3ST_2			0x00200000  /* B3 Setup Time (AOE to Read/Write) = 2 cycles		*/
+#define B3ST_3			0x00300000  /* B3 Setup Time (AOE to Read/Write) = 3 cycles		*/
+#define B3ST_4			0x00000000  /* B3 Setup Time (AOE to Read/Write) = 4 cycles		*/
+#define B3HT_1			0x00400000  /* B3 Hold Time (~Read/Write to ~AOE) = 1 cycle		*/
+#define B3HT_2			0x00800000  /* B3 Hold Time (~Read/Write to ~AOE) = 2 cycles	*/
+#define B3HT_3			0x00C00000  /* B3 Hold Time (~Read/Write to ~AOE) = 3 cycles	*/
+#define B3HT_0			0x00000000  /* B3 Hold Time (~Read/Write to ~AOE) = 0 cycles	*/
+#define B3RAT_1			0x01000000  /* B3 Read Access Time = 1 cycle					*/
+#define B3RAT_2			0x02000000  /* B3 Read Access Time = 2 cycles					*/
+#define B3RAT_3			0x03000000  /* B3 Read Access Time = 3 cycles					*/
+#define B3RAT_4			0x04000000  /* B3 Read Access Time = 4 cycles					*/
+#define B3RAT_5			0x05000000  /* B3 Read Access Time = 5 cycles					*/
+#define B3RAT_6			0x06000000  /* B3 Read Access Time = 6 cycles					*/
+#define B3RAT_7			0x07000000  /* B3 Read Access Time = 7 cycles					*/
+#define B3RAT_8			0x08000000  /* B3 Read Access Time = 8 cycles					*/
+#define B3RAT_9			0x09000000  /* B3 Read Access Time = 9 cycles					*/
+#define B3RAT_10		0x0A000000  /* B3 Read Access Time = 10 cycles					*/
+#define B3RAT_11		0x0B000000  /* B3 Read Access Time = 11 cycles					*/
+#define B3RAT_12		0x0C000000  /* B3 Read Access Time = 12 cycles					*/
+#define B3RAT_13		0x0D000000  /* B3 Read Access Time = 13 cycles					*/
+#define B3RAT_14		0x0E000000  /* B3 Read Access Time = 14 cycles					*/
+#define B3RAT_15		0x0F000000  /* B3 Read Access Time = 15 cycles					*/
+#define B3WAT_1			0x10000000  /* B3 Write Access Time = 1 cycle					*/
+#define B3WAT_2			0x20000000  /* B3 Write Access Time = 2 cycles					*/
+#define B3WAT_3			0x30000000  /* B3 Write Access Time = 3 cycles					*/
+#define B3WAT_4			0x40000000  /* B3 Write Access Time = 4 cycles					*/
+#define B3WAT_5			0x50000000  /* B3 Write Access Time = 5 cycles					*/
+#define B3WAT_6			0x60000000  /* B3 Write Access Time = 6 cycles					*/
+#define B3WAT_7			0x70000000  /* B3 Write Access Time = 7 cycles					*/
+#define B3WAT_8			0x80000000  /* B3 Write Access Time = 8 cycles					*/
+#define B3WAT_9			0x90000000  /* B3 Write Access Time = 9 cycles					*/
+#define B3WAT_10		0xA0000000  /* B3 Write Access Time = 10 cycles					*/
+#define B3WAT_11		0xB0000000  /* B3 Write Access Time = 11 cycles					*/
+#define B3WAT_12		0xC0000000  /* B3 Write Access Time = 12 cycles					*/
+#define B3WAT_13		0xD0000000  /* B3 Write Access Time = 13 cycles					*/
+#define B3WAT_14		0xE0000000  /* B3 Write Access Time = 14 cycles					*/
+#define B3WAT_15		0xF0000000  /* B3 Write Access Time = 15 cycles					*/
+
+
+/* **********************  SDRAM CONTROLLER MASKS  **********************************************/
+/* EBIU_SDGCTL Masks																			*/
+#define SCTLE			0x00000001	/* Enable SDRAM Signals										*/
+#define CL_2			0x00000008	/* SDRAM CAS Latency = 2 cycles								*/
+#define CL_3			0x0000000C	/* SDRAM CAS Latency = 3 cycles								*/
+#define PASR_ALL		0x00000000	/* All 4 SDRAM Banks Refreshed In Self-Refresh				*/
+#define PASR_B0_B1		0x00000010	/* SDRAM Banks 0 and 1 Are Refreshed In Self-Refresh		*/
+#define PASR_B0			0x00000020	/* Only SDRAM Bank 0 Is Refreshed In Self-Refresh			*/
+#define TRAS_1			0x00000040	/* SDRAM tRAS = 1 cycle										*/
+#define TRAS_2			0x00000080	/* SDRAM tRAS = 2 cycles									*/
+#define TRAS_3			0x000000C0	/* SDRAM tRAS = 3 cycles									*/
+#define TRAS_4			0x00000100	/* SDRAM tRAS = 4 cycles									*/
+#define TRAS_5			0x00000140	/* SDRAM tRAS = 5 cycles									*/
+#define TRAS_6			0x00000180	/* SDRAM tRAS = 6 cycles									*/
+#define TRAS_7			0x000001C0	/* SDRAM tRAS = 7 cycles									*/
+#define TRAS_8			0x00000200	/* SDRAM tRAS = 8 cycles									*/
+#define TRAS_9			0x00000240	/* SDRAM tRAS = 9 cycles									*/
+#define TRAS_10			0x00000280	/* SDRAM tRAS = 10 cycles									*/
+#define TRAS_11			0x000002C0	/* SDRAM tRAS = 11 cycles									*/
+#define TRAS_12			0x00000300	/* SDRAM tRAS = 12 cycles									*/
+#define TRAS_13			0x00000340	/* SDRAM tRAS = 13 cycles									*/
+#define TRAS_14			0x00000380	/* SDRAM tRAS = 14 cycles									*/
+#define TRAS_15			0x000003C0	/* SDRAM tRAS = 15 cycles									*/
+#define TRP_1			0x00000800	/* SDRAM tRP = 1 cycle										*/
+#define TRP_2			0x00001000	/* SDRAM tRP = 2 cycles										*/
+#define TRP_3			0x00001800	/* SDRAM tRP = 3 cycles										*/
+#define TRP_4			0x00002000	/* SDRAM tRP = 4 cycles										*/
+#define TRP_5			0x00002800	/* SDRAM tRP = 5 cycles										*/
+#define TRP_6			0x00003000	/* SDRAM tRP = 6 cycles										*/
+#define TRP_7			0x00003800	/* SDRAM tRP = 7 cycles										*/
+#define TRCD_1			0x00008000	/* SDRAM tRCD = 1 cycle										*/
+#define TRCD_2			0x00010000	/* SDRAM tRCD = 2 cycles									*/
+#define TRCD_3			0x00018000	/* SDRAM tRCD = 3 cycles									*/
+#define TRCD_4			0x00020000	/* SDRAM tRCD = 4 cycles									*/
+#define TRCD_5			0x00028000	/* SDRAM tRCD = 5 cycles									*/
+#define TRCD_6			0x00030000	/* SDRAM tRCD = 6 cycles									*/
+#define TRCD_7			0x00038000	/* SDRAM tRCD = 7 cycles									*/
+#define TWR_1			0x00080000	/* SDRAM tWR = 1 cycle										*/
+#define TWR_2			0x00100000	/* SDRAM tWR = 2 cycles										*/
+#define TWR_3			0x00180000	/* SDRAM tWR = 3 cycles										*/
+#define PUPSD			0x00200000	/* Power-Up Start Delay (15 SCLK Cycles Delay)				*/
+#define PSM				0x00400000	/* Power-Up Sequence (Mode Register Before/After* Refresh)	*/
+#define PSS				0x00800000	/* Enable Power-Up Sequence on Next SDRAM Access			*/
+#define SRFS			0x01000000	/* Enable SDRAM Self-Refresh Mode							*/
+#define EBUFE			0x02000000	/* Enable External Buffering Timing							*/
+#define FBBRW			0x04000000	/* Enable Fast Back-To-Back Read To Write					*/
+#define EMREN			0x10000000	/* Extended Mode Register Enable							*/
+#define TCSR			0x20000000	/* Temp-Compensated Self-Refresh Value (85/45* Deg C)		*/
+#define CDDBG			0x40000000	/* Tristate SDRAM Controls During Bus Grant					*/
+
+/* EBIU_SDBCTL Masks																		*/
+#define EBE				0x0001		/* Enable SDRAM External Bank							*/
+#define EBSZ_16			0x0000		/* SDRAM External Bank Size = 16MB	*/
+#define EBSZ_32			0x0002		/* SDRAM External Bank Size = 32MB	*/
+#define EBSZ_64			0x0004		/* SDRAM External Bank Size = 64MB	*/
+#define EBSZ_128		0x0006		/* SDRAM External Bank Size = 128MB		*/
+#define EBSZ_256		0x0008		/* SDRAM External Bank Size = 256MB 	*/
+#define EBSZ_512		0x000A		/* SDRAM External Bank Size = 512MB		*/
+#define EBCAW_8			0x0000		/* SDRAM External Bank Column Address Width = 8 Bits	*/
+#define EBCAW_9			0x0010		/* SDRAM External Bank Column Address Width = 9 Bits	*/
+#define EBCAW_10		0x0020		/* SDRAM External Bank Column Address Width = 10 Bits	*/
+#define EBCAW_11		0x0030		/* SDRAM External Bank Column Address Width = 11 Bits	*/
+
+/* EBIU_SDSTAT Masks														*/
+#define SDCI			0x0001		/* SDRAM Controller Idle 				*/
+#define SDSRA			0x0002		/* SDRAM Self-Refresh Active			*/
+#define SDPUA			0x0004		/* SDRAM Power-Up Active 				*/
+#define SDRS			0x0008		/* SDRAM Will Power-Up On Next Access	*/
+#define SDEASE			0x0010		/* SDRAM EAB Sticky Error Status		*/
+#define BGSTAT			0x0020		/* Bus Grant Status						*/
+
+
+/* **************************  DMA CONTROLLER MASKS  ********************************/
+/* DMAx_CONFIG, MDMA_yy_CONFIG Masks												*/
+#define DMAEN			0x0001		/* DMA Channel Enable							*/
+#define WNR				0x0002		/* Channel Direction (W/R*)						*/
+#define WDSIZE_8		0x0000		/* Transfer Word Size = 8						*/
+#define WDSIZE_16		0x0004		/* Transfer Word Size = 16						*/
+#define WDSIZE_32		0x0008		/* Transfer Word Size = 32						*/
+#define DMA2D			0x0010		/* DMA Mode (2D/1D*)							*/
+#define RESTART			0x0020		/* DMA Buffer Clear								*/
+#define DI_SEL			0x0040		/* Data Interrupt Timing Select					*/
+#define DI_EN			0x0080		/* Data Interrupt Enable						*/
+#define NDSIZE_0		0x0000		/* Next Descriptor Size = 0 (Stop/Autobuffer)	*/
+#define NDSIZE_1		0x0100		/* Next Descriptor Size = 1						*/
+#define NDSIZE_2		0x0200		/* Next Descriptor Size = 2						*/
+#define NDSIZE_3		0x0300		/* Next Descriptor Size = 3						*/
+#define NDSIZE_4		0x0400		/* Next Descriptor Size = 4						*/
+#define NDSIZE_5		0x0500		/* Next Descriptor Size = 5						*/
+#define NDSIZE_6		0x0600		/* Next Descriptor Size = 6						*/
+#define NDSIZE_7		0x0700		/* Next Descriptor Size = 7						*/
+#define NDSIZE_8		0x0800		/* Next Descriptor Size = 8						*/
+#define NDSIZE_9		0x0900		/* Next Descriptor Size = 9						*/
+#define NDSIZE	        	0x0900	/* Next Descriptor Size */
+#define DMAFLOW	        	0x7000	/* Flow Control */
+#define DMAFLOW_STOP		0x0000		/* Stop Mode									*/
+#define DMAFLOW_AUTO		0x1000		/* Autobuffer Mode								*/
+#define DMAFLOW_ARRAY		0x4000		/* Descriptor Array Mode						*/
+#define DMAFLOW_SMALL		0x6000		/* Small Model Descriptor List Mode				*/
+#define DMAFLOW_LARGE		0x7000		/* Large Model Descriptor List Mode				*/
+
+/* DMAx_PERIPHERAL_MAP, MDMA_yy_PERIPHERAL_MAP Masks								*/
+#define CTYPE			0x0040	/* DMA Channel Type Indicator (Memory/Peripheral*)	*/
+#define PMAP			0xF000	/* Peripheral Mapped To This Channel				*/
+#define PMAP_PPI		0x0000	/* 		PPI Port DMA								*/
+#define	PMAP_EMACRX		0x1000	/* 		Ethernet Receive DMA						*/
+#define PMAP_EMACTX		0x2000	/* 		Ethernet Transmit DMA						*/
+#define PMAP_SPORT0RX	0x3000	/* 		SPORT0 Receive DMA							*/
+#define PMAP_SPORT0TX	0x4000	/* 		SPORT0 Transmit DMA							*/
+#define PMAP_SPORT1RX	0x5000	/* 		SPORT1 Receive DMA							*/
+#define PMAP_SPORT1TX	0x6000	/* 		SPORT1 Transmit DMA							*/
+#define PMAP_SPI		0x7000	/* 		SPI Port DMA								*/
+#define PMAP_UART0RX	0x8000	/* 		UART0 Port Receive DMA						*/
+#define PMAP_UART0TX	0x9000	/* 		UART0 Port Transmit DMA						*/
+#define	PMAP_UART1RX	0xA000	/* 		UART1 Port Receive DMA						*/
+#define	PMAP_UART1TX	0xB000	/* 		UART1 Port Transmit DMA						*/
+
+/* DMAx_IRQ_STATUS, MDMA_yy_IRQ_STATUS Masks						*/
+#define DMA_DONE		0x0001	/* DMA Completion Interrupt Status	*/
+#define DMA_ERR			0x0002	/* DMA Error Interrupt Status		*/
+#define DFETCH			0x0004	/* DMA Descriptor Fetch Indicator	*/
+#define DMA_RUN			0x0008	/* DMA Channel Running Indicator	*/
+
+
+/*  ************  PARALLEL PERIPHERAL INTERFACE (PPI) MASKS *************/
+/*  PPI_CONTROL Masks													*/
+#define PORT_EN			0x0001		/* PPI Port Enable					*/
+#define PORT_DIR		0x0002		/* PPI Port Direction				*/
+#define XFR_TYPE		0x000C		/* PPI Transfer Type				*/
+#define PORT_CFG		0x0030		/* PPI Port Configuration			*/
+#define FLD_SEL			0x0040		/* PPI Active Field Select			*/
+#define PACK_EN			0x0080		/* PPI Packing Mode					*/
+#define DMA32			0x0100		/* PPI 32-bit DMA Enable			*/
+#define SKIP_EN			0x0200		/* PPI Skip Element Enable			*/
+#define SKIP_EO			0x0400		/* PPI Skip Even/Odd Elements		*/
+#define DLEN_8			0x0000		/* Data Length = 8 Bits				*/
+#define DLEN_10			0x0800		/* Data Length = 10 Bits			*/
+#define DLEN_11			0x1000		/* Data Length = 11 Bits			*/
+#define DLEN_12			0x1800		/* Data Length = 12 Bits			*/
+#define DLEN_13			0x2000		/* Data Length = 13 Bits			*/
+#define DLEN_14			0x2800		/* Data Length = 14 Bits			*/
+#define DLEN_15			0x3000		/* Data Length = 15 Bits			*/
+#define DLEN_16			0x3800		/* Data Length = 16 Bits			*/
+#define DLENGTH			0x3800		/* PPI Data Length  */
+#define POLC			0x4000		/* PPI Clock Polarity				*/
+#define POLS			0x8000		/* PPI Frame Sync Polarity			*/
+
+/* PPI_STATUS Masks														*/
+#define FLD				0x0400		/* Field Indicator					*/
+#define FT_ERR			0x0800		/* Frame Track Error				*/
+#define OVR				0x1000		/* FIFO Overflow Error				*/
+#define UNDR			0x2000		/* FIFO Underrun Error				*/
+#define ERR_DET			0x4000		/* Error Detected Indicator			*/
+#define ERR_NCOR		0x8000		/* Error Not Corrected Indicator	*/
+
+
+/*  ********************  TWO-WIRE INTERFACE (TWI) MASKS  ***********************/
+/* TWI_CLKDIV Macros (Use: *pTWI_CLKDIV = CLKLOW(x)|CLKHI(y);  )				*/
+#define	CLKLOW(x)	((x) & 0xFF)		/* Periods Clock Is Held Low			*/
+#define CLKHI(y)	(((y)&0xFF)<<0x8)	/* Periods Before New Clock Low			*/
+
+/* TWI_PRESCALE Masks															*/
+#define	PRESCALE	0x007F		/* SCLKs Per Internal Time Reference (10MHz)	*/
+#define	TWI_ENA		0x0080		/* TWI Enable									*/
+#define	SCCB		0x0200		/* SCCB Compatibility Enable					*/
+
+/* TWI_SLAVE_CTRL Masks															*/
+#define	SEN			0x0001		/* Slave Enable									*/
+#define	SADD_LEN	0x0002		/* Slave Address Length							*/
+#define	STDVAL		0x0004		/* Slave Transmit Data Valid					*/
+#define	NAK			0x0008		/* NAK/ACK* Generated At Conclusion Of Transfer */
+#define	GEN			0x0010		/* General Call Adrress Matching Enabled		*/
+
+/* TWI_SLAVE_STAT Masks															*/
+#define	SDIR		0x0001		/* Slave Transfer Direction (Transmit/Receive*)	*/
+#define GCALL		0x0002		/* General Call Indicator						*/
+
+/* TWI_MASTER_CTRL Masks													*/
+#define	MEN			0x0001		/* Master Mode Enable						*/
+#define	MADD_LEN	0x0002		/* Master Address Length					*/
+#define	MDIR		0x0004		/* Master Transmit Direction (RX/TX*)		*/
+#define	FAST		0x0008		/* Use Fast Mode Timing Specs				*/
+#define	STOP		0x0010		/* Issue Stop Condition						*/
+#define	RSTART		0x0020		/* Repeat Start or Stop* At End Of Transfer	*/
+#define	DCNT		0x3FC0		/* Data Bytes To Transfer					*/
+#define	SDAOVR		0x4000		/* Serial Data Override						*/
+#define	SCLOVR		0x8000		/* Serial Clock Override					*/
+
+/* TWI_MASTER_STAT Masks														*/
+#define	MPROG		0x0001		/* Master Transfer In Progress					*/
+#define	LOSTARB		0x0002		/* Lost Arbitration Indicator (Xfer Aborted)	*/
+#define	ANAK		0x0004		/* Address Not Acknowledged						*/
+#define	DNAK		0x0008		/* Data Not Acknowledged						*/
+#define	BUFRDERR	0x0010		/* Buffer Read Error							*/
+#define	BUFWRERR	0x0020		/* Buffer Write Error							*/
+#define	SDASEN		0x0040		/* Serial Data Sense							*/
+#define	SCLSEN		0x0080		/* Serial Clock Sense							*/
+#define	BUSBUSY		0x0100		/* Bus Busy Indicator							*/
+
+/* TWI_INT_SRC and TWI_INT_ENABLE Masks						*/
+#define	SINIT		0x0001		/* Slave Transfer Initiated	*/
+#define	SCOMP		0x0002		/* Slave Transfer Complete	*/
+#define	SERR		0x0004		/* Slave Transfer Error		*/
+#define	SOVF		0x0008		/* Slave Overflow			*/
+#define	MCOMP		0x0010		/* Master Transfer Complete	*/
+#define	MERR		0x0020		/* Master Transfer Error	*/
+#define	XMTSERV		0x0040		/* Transmit FIFO Service	*/
+#define	RCVSERV		0x0080		/* Receive FIFO Service		*/
+
+/* TWI_FIFO_CTRL Masks												*/
+#define	XMTFLUSH	0x0001		/* Transmit Buffer Flush			*/
+#define	RCVFLUSH	0x0002		/* Receive Buffer Flush				*/
+#define	XMTINTLEN	0x0004		/* Transmit Buffer Interrupt Length	*/
+#define	RCVINTLEN	0x0008		/* Receive Buffer Interrupt Length	*/
+
+/* TWI_FIFO_STAT Masks															*/
+#define	XMTSTAT		0x0003		/* Transmit FIFO Status							*/
+#define	XMT_EMPTY	0x0000		/* 		Transmit FIFO Empty						*/
+#define	XMT_HALF	0x0001		/* 		Transmit FIFO Has 1 Byte To Write		*/
+#define	XMT_FULL	0x0003		/* 		Transmit FIFO Full (2 Bytes To Write)	*/
+
+#define	RCVSTAT		0x000C		/* Receive FIFO Status							*/
+#define	RCV_EMPTY	0x0000		/* 		Receive FIFO Empty						*/
+#define	RCV_HALF	0x0004		/* 		Receive FIFO Has 1 Byte To Read			*/
+#define	RCV_FULL	0x000C		/* 		Receive FIFO Full (2 Bytes To Read)		*/
+
+
+/* Omit CAN masks from defBF534.h */
+
+/*  *******************  PIN CONTROL REGISTER MASKS  ************************/
+/* PORT_MUX Masks															*/
+#define	PJSE			0x0001			/* Port J SPI/SPORT Enable			*/
+#define	PJSE_SPORT		0x0000			/* 		Enable TFS0/DT0PRI			*/
+#define	PJSE_SPI		0x0001			/* 		Enable SPI_SSEL3:2			*/
+
+#define	PJCE(x)			(((x)&0x3)<<1)	/* Port J CAN/SPI/SPORT Enable		*/
+#define	PJCE_SPORT		0x0000			/* 		Enable DR0SEC/DT0SEC		*/
+#define	PJCE_CAN		0x0002			/* 		Enable CAN RX/TX			*/
+#define	PJCE_SPI		0x0004			/* 		Enable SPI_SSEL7			*/
+
+#define	PFDE			0x0008			/* Port F DMA Request Enable		*/
+#define	PFDE_UART		0x0000			/* 		Enable UART0 RX/TX			*/
+#define	PFDE_DMA		0x0008			/* 		Enable DMAR1:0				*/
+
+#define	PFTE			0x0010			/* Port F Timer Enable				*/
+#define	PFTE_UART		0x0000			/*		Enable UART1 RX/TX			*/
+#define	PFTE_TIMER		0x0010			/* 		Enable TMR7:6				*/
+
+#define	PFS6E			0x0020			/* Port F SPI SSEL 6 Enable			*/
+#define	PFS6E_TIMER		0x0000			/*		Enable TMR5					*/
+#define	PFS6E_SPI		0x0020			/* 		Enable SPI_SSEL6			*/
+
+#define	PFS5E			0x0040			/* Port F SPI SSEL 5 Enable			*/
+#define	PFS5E_TIMER		0x0000			/*		Enable TMR4					*/
+#define	PFS5E_SPI		0x0040			/* 		Enable SPI_SSEL5			*/
+
+#define	PFS4E			0x0080			/* Port F SPI SSEL 4 Enable			*/
+#define	PFS4E_TIMER		0x0000			/*		Enable TMR3					*/
+#define	PFS4E_SPI		0x0080			/* 		Enable SPI_SSEL4			*/
+
+#define	PFFE			0x0100			/* Port F PPI Frame Sync Enable		*/
+#define	PFFE_TIMER		0x0000			/* 		Enable TMR2					*/
+#define	PFFE_PPI		0x0100			/* 		Enable PPI FS3				*/
+
+#define	PGSE			0x0200			/* Port G SPORT1 Secondary Enable	*/
+#define	PGSE_PPI		0x0000			/* 		Enable PPI D9:8				*/
+#define	PGSE_SPORT		0x0200			/* 		Enable DR1SEC/DT1SEC		*/
+
+#define	PGRE			0x0400			/* Port G SPORT1 Receive Enable		*/
+#define	PGRE_PPI		0x0000			/* 		Enable PPI D12:10			*/
+#define	PGRE_SPORT		0x0400			/* 		Enable DR1PRI/RFS1/RSCLK1	*/
+
+#define	PGTE			0x0800			/* Port G SPORT1 Transmit Enable	*/
+#define	PGTE_PPI		0x0000			/* 		Enable PPI D15:13			*/
+#define	PGTE_SPORT		0x0800			/* 		Enable DT1PRI/TFS1/TSCLK1	*/
+
+
+/*  ******************  HANDSHAKE DMA (HDMA) MASKS  *********************/
+/* HDMAx_CTL Masks														*/
+#define	HMDMAEN		0x0001	/* Enable Handshake DMA 0/1					*/
+#define	REP			0x0002	/* HDMA Request Polarity					*/
+#define	UTE			0x0004	/* Urgency Threshold Enable					*/
+#define	OIE			0x0010	/* Overflow Interrupt Enable				*/
+#define	BDIE		0x0020	/* Block Done Interrupt Enable				*/
+#define	MBDI		0x0040	/* Mask Block Done IRQ If Pending ECNT		*/
+#define	DRQ			0x0300	/* HDMA Request Type						*/
+#define	DRQ_NONE	0x0000	/* 		No Request							*/
+#define	DRQ_SINGLE	0x0100	/* 		Channels Request Single				*/
+#define	DRQ_MULTI	0x0200	/* 		Channels Request Multi (Default)	*/
+#define	DRQ_URGENT	0x0300	/* 		Channels Request Multi Urgent		*/
+#define	RBC			0x1000	/* Reload BCNT With IBCNT					*/
+#define	PS			0x2000	/* HDMA Pin Status							*/
+#define	OI			0x4000	/* Overflow Interrupt Generated				*/
+#define	BDI			0x8000	/* Block Done Interrupt Generated			*/
+
+/* entry addresses of the user-callable Boot ROM functions */
+
+#define _BOOTROM_RESET 0xEF000000 
+#define _BOOTROM_FINAL_INIT 0xEF000002 
+#define _BOOTROM_DO_MEMORY_DMA 0xEF000006
+#define _BOOTROM_BOOT_DXE_FLASH 0xEF000008 
+#define _BOOTROM_BOOT_DXE_SPI 0xEF00000A 
+#define _BOOTROM_BOOT_DXE_TWI 0xEF00000C 
+#define _BOOTROM_GET_DXE_ADDRESS_FLASH 0xEF000010
+#define _BOOTROM_GET_DXE_ADDRESS_SPI 0xEF000012
+#define _BOOTROM_GET_DXE_ADDRESS_TWI 0xEF000014
+
+/* Alternate Deprecated Macros Provided For Backwards Code Compatibility */
+#define	PGDE_UART   PFDE_UART
+#define	PGDE_DMA    PFDE_DMA
+#define	CKELOW		SCKELOW
+
+/* ==== end from defBF534.h ==== */
+
+/* HOST Port Registers */
+
+#define                     HOST_CONTROL  0xffc03400   /* HOST Control Register */
+#define                      HOST_STATUS  0xffc03404   /* HOST Status Register */
+#define                     HOST_TIMEOUT  0xffc03408   /* HOST Acknowledge Mode Timeout Register */
+
+/* Counter Registers */
+
+#define                       CNT_CONFIG  0xffc03500   /* Configuration Register */
+#define                        CNT_IMASK  0xffc03504   /* Interrupt Mask Register */
+#define                       CNT_STATUS  0xffc03508   /* Status Register */
+#define                      CNT_COMMAND  0xffc0350c   /* Command Register */
+#define                     CNT_DEBOUNCE  0xffc03510   /* Debounce Register */
+#define                      CNT_COUNTER  0xffc03514   /* Counter Register */
+#define                          CNT_MAX  0xffc03518   /* Maximal Count Register */
+#define                          CNT_MIN  0xffc0351c   /* Minimal Count Register */
+
+/* OTP/FUSE Registers */
+
+#define                      OTP_CONTROL  0xffc03600   /* OTP/Fuse Control Register */
+#define                          OTP_BEN  0xffc03604   /* OTP/Fuse Byte Enable */
+#define                       OTP_STATUS  0xffc03608   /* OTP/Fuse Status */
+#define                       OTP_TIMING  0xffc0360c   /* OTP/Fuse Access Timing */
+
+/* Security Registers */
+
+#define                    SECURE_SYSSWT  0xffc03620   /* Secure System Switches */
+#define                   SECURE_CONTROL  0xffc03624   /* Secure Control */
+#define                    SECURE_STATUS  0xffc03628   /* Secure Status */
+
+/* OTP Read/Write Data Buffer Registers */
+
+#define                        OTP_DATA0  0xffc03680   /* OTP/Fuse Data (OTP_DATA0-3) accesses the fuse read write buffer */
+#define                        OTP_DATA1  0xffc03684   /* OTP/Fuse Data (OTP_DATA0-3) accesses the fuse read write buffer */
+#define                        OTP_DATA2  0xffc03688   /* OTP/Fuse Data (OTP_DATA0-3) accesses the fuse read write buffer */
+#define                        OTP_DATA3  0xffc0368c   /* OTP/Fuse Data (OTP_DATA0-3) accesses the fuse read write buffer */
+
+/* NFC Registers */
+
+#define                          NFC_CTL  0xffc03700   /* NAND Control Register */
+#define                         NFC_STAT  0xffc03704   /* NAND Status Register */
+#define                      NFC_IRQSTAT  0xffc03708   /* NAND Interrupt Status Register */
+#define                      NFC_IRQMASK  0xffc0370c   /* NAND Interrupt Mask Register */
+#define                         NFC_ECC0  0xffc03710   /* NAND ECC Register 0 */
+#define                         NFC_ECC1  0xffc03714   /* NAND ECC Register 1 */
+#define                         NFC_ECC2  0xffc03718   /* NAND ECC Register 2 */
+#define                         NFC_ECC3  0xffc0371c   /* NAND ECC Register 3 */
+#define                        NFC_COUNT  0xffc03720   /* NAND ECC Count Register */
+#define                          NFC_RST  0xffc03724   /* NAND ECC Reset Register */
+#define                        NFC_PGCTL  0xffc03728   /* NAND Page Control Register */
+#define                         NFC_READ  0xffc0372c   /* NAND Read Data Register */
+#define                         NFC_ADDR  0xffc03740   /* NAND Address Register */
+#define                          NFC_CMD  0xffc03744   /* NAND Command Register */
+#define                      NFC_DATA_WR  0xffc03748   /* NAND Data Write Register */
+#define                      NFC_DATA_RD  0xffc0374c   /* NAND Data Read Register */
+
+/* ********************************************************** */
+/*     SINGLE BIT MACRO PAIRS (bit mask and negated one)      */
+/*     and MULTI BIT READ MACROS                              */
+/* ********************************************************** */
+
+/* Bit masks for HOST_CONTROL */
+
+#define                   HOST_CNTR_HOST_EN  0x1        /* Host Enable */
+#define                  HOST_CNTR_nHOST_EN  0x0
+#define                  HOST_CNTR_HOST_END  0x2        /* Host Endianess */
+#define                 HOST_CNTR_nHOST_END  0x0
+#define                 HOST_CNTR_DATA_SIZE  0x4        /* Data Size */
+#define                HOST_CNTR_nDATA_SIZE  0x0
+#define                  HOST_CNTR_HOST_RST  0x8        /* Host Reset */
+#define                 HOST_CNTR_nHOST_RST  0x0
+#define                  HOST_CNTR_HRDY_OVR  0x20       /* Host Ready Override */
+#define                 HOST_CNTR_nHRDY_OVR  0x0
+#define                  HOST_CNTR_INT_MODE  0x40       /* Interrupt Mode */
+#define                 HOST_CNTR_nINT_MODE  0x0
+#define                     HOST_CNTR_BT_EN  0x80       /* Bus Timeout Enable */
+#define                   HOST_CNTR_ nBT_EN  0x0
+#define                       HOST_CNTR_EHW  0x100      /* Enable Host Write */
+#define                      HOST_CNTR_nEHW  0x0
+#define                       HOST_CNTR_EHR  0x200      /* Enable Host Read */
+#define                      HOST_CNTR_nEHR  0x0
+#define                       HOST_CNTR_BDR  0x400      /* Burst DMA Requests */
+#define                      HOST_CNTR_nBDR  0x0
+
+/* Bit masks for HOST_STATUS */
+
+#define                     HOST_STAT_READY  0x1        /* DMA Ready */
+#define                    HOST_STAT_nREADY  0x0
+#define                  HOST_STAT_FIFOFULL  0x2        /* FIFO Full */
+#define                 HOST_STAT_nFIFOFULL  0x0
+#define                 HOST_STAT_FIFOEMPTY  0x4        /* FIFO Empty */
+#define                HOST_STAT_nFIFOEMPTY  0x0
+#define                  HOST_STAT_COMPLETE  0x8        /* DMA Complete */
+#define                 HOST_STAT_nCOMPLETE  0x0
+#define                      HOST_STAT_HSHK  0x10       /* Host Handshake */
+#define                     HOST_STAT_nHSHK  0x0
+#define                   HOST_STAT_TIMEOUT  0x20       /* Host Timeout */
+#define                  HOST_STAT_nTIMEOUT  0x0
+#define                      HOST_STAT_HIRQ  0x40       /* Host Interrupt Request */
+#define                     HOST_STAT_nHIRQ  0x0
+#define                HOST_STAT_ALLOW_CNFG  0x80       /* Allow New Configuration */
+#define               HOST_STAT_nALLOW_CNFG  0x0
+#define                   HOST_STAT_DMA_DIR  0x100      /* DMA Direction */
+#define                  HOST_STAT_nDMA_DIR  0x0
+#define                       HOST_STAT_BTE  0x200      /* Bus Timeout Enabled */
+#define                      HOST_STAT_nBTE  0x0
+#define               HOST_STAT_HOSTRD_DONE  0x8000     /* Host Read Completion Interrupt */
+#define              HOST_STAT_nHOSTRD_DONE  0x0
+
+/* Bit masks for HOST_TIMEOUT */
+
+#define             HOST_COUNT_TIMEOUT  0x7ff      /* Host Timeout count */
+
+/* Bit masks for CNT_CONFIG */
+
+#define                      CNTE  0x1        /* Counter Enable */
+#define                     nCNTE  0x0       
+#define                      DEBE  0x2        /* Debounce Enable */
+#define                     nDEBE  0x0       
+#define                    CDGINV  0x10       /* CDG Pin Polarity Invert */
+#define                   nCDGINV  0x0       
+#define                    CUDINV  0x20       /* CUD Pin Polarity Invert */
+#define                   nCUDINV  0x0       
+#define                    CZMINV  0x40       /* CZM Pin Polarity Invert */
+#define                   nCZMINV  0x0       
+#define                   CNTMODE  0x700      /* Counter Operating Mode */
+#define                      ZMZC  0x800      /* CZM Zeroes Counter Enable */
+#define                     nZMZC  0x0       
+#define                   BNDMODE  0x3000     /* Boundary register Mode */
+#define                    INPDIS  0x8000     /* CUG and CDG Input Disable */
+#define                   nINPDIS  0x0       
+
+/* Bit masks for CNT_IMASK */
+
+#define                      ICIE  0x1        /* Illegal Gray/Binary Code Interrupt Enable */
+#define                     nICIE  0x0       
+#define                      UCIE  0x2        /* Up count Interrupt Enable */
+#define                     nUCIE  0x0       
+#define                      DCIE  0x4        /* Down count Interrupt Enable */
+#define                     nDCIE  0x0       
+#define                    MINCIE  0x8        /* Min Count Interrupt Enable */
+#define                   nMINCIE  0x0       
+#define                    MAXCIE  0x10       /* Max Count Interrupt Enable */
+#define                   nMAXCIE  0x0       
+#define                   COV31IE  0x20       /* Bit 31 Overflow Interrupt Enable */
+#define                  nCOV31IE  0x0       
+#define                   COV15IE  0x40       /* Bit 15 Overflow Interrupt Enable */
+#define                  nCOV15IE  0x0       
+#define                   CZEROIE  0x80       /* Count to Zero Interrupt Enable */
+#define                  nCZEROIE  0x0       
+#define                     CZMIE  0x100      /* CZM Pin Interrupt Enable */
+#define                    nCZMIE  0x0       
+#define                    CZMEIE  0x200      /* CZM Error Interrupt Enable */
+#define                   nCZMEIE  0x0       
+#define                    CZMZIE  0x400      /* CZM Zeroes Counter Interrupt Enable */
+#define                   nCZMZIE  0x0       
+
+/* Bit masks for CNT_STATUS */
+
+#define                      ICII  0x1        /* Illegal Gray/Binary Code Interrupt Identifier */
+#define                     nICII  0x0       
+#define                      UCII  0x2        /* Up count Interrupt Identifier */
+#define                     nUCII  0x0       
+#define                      DCII  0x4        /* Down count Interrupt Identifier */
+#define                     nDCII  0x0       
+#define                    MINCII  0x8        /* Min Count Interrupt Identifier */
+#define                   nMINCII  0x0       
+#define                    MAXCII  0x10       /* Max Count Interrupt Identifier */
+#define                   nMAXCII  0x0       
+#define                   COV31II  0x20       /* Bit 31 Overflow Interrupt Identifier */
+#define                  nCOV31II  0x0       
+#define                   COV15II  0x40       /* Bit 15 Overflow Interrupt Identifier */
+#define                  nCOV15II  0x0       
+#define                   CZEROII  0x80       /* Count to Zero Interrupt Identifier */
+#define                  nCZEROII  0x0       
+#define                     CZMII  0x100      /* CZM Pin Interrupt Identifier */
+#define                    nCZMII  0x0       
+#define                    CZMEII  0x200      /* CZM Error Interrupt Identifier */
+#define                   nCZMEII  0x0       
+#define                    CZMZII  0x400      /* CZM Zeroes Counter Interrupt Identifier */
+#define                   nCZMZII  0x0       
+
+/* Bit masks for CNT_COMMAND */
+
+#define                    W1LCNT  0xf        /* Load Counter Register */
+#define                    W1LMIN  0xf0       /* Load Min Register */
+#define                    W1LMAX  0xf00      /* Load Max Register */
+#define                  W1ZMONCE  0x1000     /* Enable CZM Clear Counter Once */
+#define                 nW1ZMONCE  0x0       
+
+/* Bit masks for CNT_DEBOUNCE */
+
+#define                 DPRESCALE  0xf        /* Load Counter Register */
+
+/* Bit masks for OTP_CONTROL */
+
+#define                FUSE_FADDR  0x1ff      /* OTP/Fuse Address */
+#define                      FIEN  0x800      /* OTP/Fuse Interrupt Enable */
+#define                     nFIEN  0x0       
+#define                  FTESTDEC  0x1000     /* OTP/Fuse Test Decoder */
+#define                 nFTESTDEC  0x0       
+#define                   FWRTEST  0x2000     /* OTP/Fuse Write Test */
+#define                  nFWRTEST  0x0       
+#define                     FRDEN  0x4000     /* OTP/Fuse Read Enable */
+#define                    nFRDEN  0x0       
+#define                     FWREN  0x8000     /* OTP/Fuse Write Enable */
+#define                    nFWREN  0x0       
+
+/* Bit masks for OTP_BEN */
+
+#define                      FBEN  0xffff     /* OTP/Fuse Byte Enable */
+
+/* Bit masks for OTP_STATUS */
+
+#define                     FCOMP  0x1        /* OTP/Fuse Access Complete */
+#define                    nFCOMP  0x0       
+#define                    FERROR  0x2        /* OTP/Fuse Access Error */
+#define                   nFERROR  0x0       
+#define                  MMRGLOAD  0x10       /* Memory Mapped Register Gasket Load */
+#define                 nMMRGLOAD  0x0       
+#define                  MMRGLOCK  0x20       /* Memory Mapped Register Gasket Lock */
+#define                 nMMRGLOCK  0x0       
+#define                    FPGMEN  0x40       /* OTP/Fuse Program Enable */
+#define                   nFPGMEN  0x0       
+
+/* Bit masks for OTP_TIMING */
+
+#define                   USECDIV  0xff       /* Micro Second Divider */
+#define                   READACC  0x7f00     /* Read Access Time */
+#define                   CPUMPRL  0x38000    /* Charge Pump Release Time */
+#define                   CPUMPSU  0xc0000    /* Charge Pump Setup Time */
+#define                   CPUMPHD  0xf00000   /* Charge Pump Hold Time */
+#define                   PGMTIME  0xff000000 /* Program Time */
+
+/* Bit masks for SECURE_SYSSWT */
+
+#define                   EMUDABL  0x1        /* Emulation Disable. */
+#define                  nEMUDABL  0x0       
+#define                   RSTDABL  0x2        /* Reset Disable */
+#define                  nRSTDABL  0x0       
+#define                   L1IDABL  0x1c       /* L1 Instruction Memory Disable. */
+#define                  L1DADABL  0xe0       /* L1 Data Bank A Memory Disable. */
+#define                  L1DBDABL  0x700      /* L1 Data Bank B Memory Disable. */
+#define                   DMA0OVR  0x800      /* DMA0 Memory Access Override */
+#define                  nDMA0OVR  0x0       
+#define                   DMA1OVR  0x1000     /* DMA1 Memory Access Override */
+#define                  nDMA1OVR  0x0       
+#define                    EMUOVR  0x4000     /* Emulation Override */
+#define                   nEMUOVR  0x0       
+#define                    OTPSEN  0x8000     /* OTP Secrets Enable. */
+#define                   nOTPSEN  0x0       
+#define                    L2DABL  0x70000    /* L2 Memory Disable. */
+
+/* Bit masks for SECURE_CONTROL */
+
+#define                   SECURE0  0x1        /* SECURE 0 */
+#define                  nSECURE0  0x0       
+#define                   SECURE1  0x2        /* SECURE 1 */
+#define                  nSECURE1  0x0       
+#define                   SECURE2  0x4        /* SECURE 2 */
+#define                  nSECURE2  0x0       
+#define                   SECURE3  0x8        /* SECURE 3 */
+#define                  nSECURE3  0x0       
+
+/* Bit masks for SECURE_STATUS */
+
+#define                   SECMODE  0x3        /* Secured Mode Control State */
+#define                       NMI  0x4        /* Non Maskable Interrupt */
+#define                      nNMI  0x0       
+#define                   AFVALID  0x8        /* Authentication Firmware Valid */
+#define                  nAFVALID  0x0       
+#define                    AFEXIT  0x10       /* Authentication Firmware Exit */
+#define                   nAFEXIT  0x0       
+#define                   SECSTAT  0xe0       /* Secure Status */
+
+/* Bit masks for NFC_CTL */
+
+#define                    WR_DLY  0xf        /* Write Strobe Delay */
+#define                    RD_DLY  0xf0       /* Read Strobe Delay */
+#define                    NWIDTH  0x100      /* NAND Data Width */
+#define                   nNWIDTH  0x0       
+#define                   PG_SIZE  0x200      /* Page Size */
+#define                  nPG_SIZE  0x0       
+
+/* Bit masks for NFC_STAT */
+
+#define                     NBUSY  0x1        /* Not Busy */
+#define                    nNBUSY  0x0       
+#define                   WB_FULL  0x2        /* Write Buffer Full */
+#define                  nWB_FULL  0x0       
+#define                PG_WR_STAT  0x4        /* Page Write Pending */
+#define               nPG_WR_STAT  0x0       
+#define                PG_RD_STAT  0x8        /* Page Read Pending */
+#define               nPG_RD_STAT  0x0       
+#define                  WB_EMPTY  0x10       /* Write Buffer Empty */
+#define                 nWB_EMPTY  0x0       
+
+/* Bit masks for NFC_IRQSTAT */
+
+#define                  NBUSYIRQ  0x1        /* Not Busy IRQ */
+#define                 nNBUSYIRQ  0x0       
+#define                    WB_OVF  0x2        /* Write Buffer Overflow */
+#define                   nWB_OVF  0x0       
+#define                   WB_EDGE  0x4        /* Write Buffer Edge Detect */
+#define                  nWB_EDGE  0x0       
+#define                    RD_RDY  0x8        /* Read Data Ready */
+#define                   nRD_RDY  0x0       
+#define                   WR_DONE  0x10       /* Page Write Done */
+#define                  nWR_DONE  0x0       
+
+/* Bit masks for NFC_IRQMASK */
+
+#define              MASK_BUSYIRQ  0x1        /* Mask Not Busy IRQ */
+#define             nMASK_BUSYIRQ  0x0       
+#define                MASK_WBOVF  0x2        /* Mask Write Buffer Overflow */
+#define               nMASK_WBOVF  0x0       
+#define              MASK_WBEMPTY  0x4        /* Mask Write Buffer Empty */
+#define             nMASK_WBEMPTY  0x0       
+#define                MASK_RDRDY  0x8        /* Mask Read Data Ready */
+#define               nMASK_RDRDY  0x0       
+#define               MASK_WRDONE  0x10       /* Mask Write Done */
+#define              nMASK_WRDONE  0x0       
+
+/* Bit masks for NFC_RST */
+
+#define                   ECC_RST  0x1        /* ECC (and NFC counters) Reset */
+#define                  nECC_RST  0x0       
+
+/* Bit masks for NFC_PGCTL */
+
+#define               PG_RD_START  0x1        /* Page Read Start */
+#define              nPG_RD_START  0x0       
+#define               PG_WR_START  0x2        /* Page Write Start */
+#define              nPG_WR_START  0x0       
+
+/* Bit masks for NFC_ECC0 */
+
+#define                      ECC0  0x7ff      /* Parity Calculation Result0 */
+
+/* Bit masks for NFC_ECC1 */
+
+#define                      ECC1  0x7ff      /* Parity Calculation Result1 */
+
+/* Bit masks for NFC_ECC2 */
+
+#define                      ECC2  0x7ff      /* Parity Calculation Result2 */
+
+/* Bit masks for NFC_ECC3 */
+
+#define                      ECC3  0x7ff      /* Parity Calculation Result3 */
+
+/* Bit masks for NFC_COUNT */
+
+#define                    ECCCNT  0x3ff      /* Transfer Count */
+
+
+#endif /* _DEF_BF52X_H */
diff --git a/arch/blackfin/mach-bf527/include/mach/dma.h b/arch/blackfin/mach-bf527/include/mach/dma.h
new file mode 100644
index 00000000000..49dd693223e
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/dma.h
@@ -0,0 +1,62 @@
+/*
+ * file:        include/asm-blackfin/mach-bf527/dma.h
+ * based on:	include/asm-blackfin/mach-bf537/dma.h
+ * author:	Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * created:
+ * description:
+ *	system DMA map
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#ifndef _MACH_DMA_H_
+#define _MACH_DMA_H_
+
+#define MAX_BLACKFIN_DMA_CHANNEL 16
+
+#define CH_PPI 			0	/* PPI receive/transmit or NFC */
+#define CH_EMAC_RX 		1	/* Ethernet MAC receive or HOSTDP */
+#define CH_EMAC_HOSTDP 		1	/* Ethernet MAC receive or HOSTDP */
+#define CH_EMAC_TX 		2	/* Ethernet MAC transmit or NFC */
+#define CH_SPORT0_RX 		3	/* SPORT0 receive */
+#define CH_SPORT0_TX 		4	/* SPORT0 transmit */
+#define CH_SPORT1_RX 		5	/* SPORT1 receive */
+#define CH_SPORT1_TX 		6	/* SPORT1 transmit */
+#define CH_SPI 			7	/* SPI transmit/receive */
+#define CH_UART0_RX 		8	/* UART0 receive */
+#define CH_UART0_TX 		9	/* UART0 transmit */
+#define CH_UART1_RX 		10	/* UART1 receive */
+#define CH_UART1_TX 		11	/* UART1 transmit */
+
+#define CH_MEM_STREAM0_DEST	12	/* TX */
+#define CH_MEM_STREAM0_SRC  	13	/* RX */
+#define CH_MEM_STREAM1_DEST	14	/* TX */
+#define CH_MEM_STREAM1_SRC 	15	/* RX */
+
+#if defined(CONFIG_BF527_NAND_D_PORTF)
+#define CH_NFC			CH_PPI	/* PPI receive/transmit or NFC */
+#elif defined(CONFIG_BF527_NAND_D_PORTH)
+#define CH_NFC			CH_EMAC_TX /* PPI receive/transmit or NFC */
+#endif
+
+#endif
diff --git a/arch/blackfin/mach-bf527/include/mach/irq.h b/arch/blackfin/mach-bf527/include/mach/irq.h
new file mode 100644
index 00000000000..4e2b3f2020e
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/irq.h
@@ -0,0 +1,259 @@
+/*
+ * file:	include/asm-blackfin/mach-bf527/irq.h
+ * based on:	include/asm-blackfin/mach-bf537/irq.h
+ * author:	Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * created:
+ * description:
+ *	system mmr register map
+ * rev:
+ *
+ * modified:
+ *
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#ifndef _BF527_IRQ_H_
+#define _BF527_IRQ_H_
+
+/*
+ * Interrupt source definitions
+	Event Source    Core Event Name
+	Core        Emulation               **
+	Events         (highest priority)  EMU         0
+	Reset                   RST         1
+	NMI                     NMI         2
+	Exception               EVX         3
+	Reserved                --          4
+	Hardware Error          IVHW        5
+	Core Timer              IVTMR       6 *
+
+	.....
+
+	 Software Interrupt 1    IVG14       31
+	 Software Interrupt 2    --
+	 (lowest priority)  IVG15       32 *
+*/
+
+#define NR_PERI_INTS    (2 * 32)
+
+/* The ABSTRACT IRQ definitions */
+/** the first seven of the following are fixed, the rest you change if you need to **/
+#define IRQ_EMU			0	/* Emulation */
+#define IRQ_RST			1	/* reset */
+#define IRQ_NMI			2	/* Non Maskable */
+#define IRQ_EVX			3	/* Exception */
+#define IRQ_UNUSED		4	/* - unused interrupt */
+#define IRQ_HWERR		5	/* Hardware Error */
+#define IRQ_CORETMR		6	/* Core timer */
+
+#define BFIN_IRQ(x)		((x) + 7)
+
+#define IRQ_PLL_WAKEUP		BFIN_IRQ(0)	/* PLL Wakeup Interrupt */
+#define IRQ_DMA0_ERROR		BFIN_IRQ(1)	/* DMA Error 0 (generic) */
+#define IRQ_DMAR0_BLK		BFIN_IRQ(2)	/* DMAR0 Block Interrupt */
+#define IRQ_DMAR1_BLK		BFIN_IRQ(3)	/* DMAR1 Block Interrupt */
+#define IRQ_DMAR0_OVR		BFIN_IRQ(4)	/* DMAR0 Overflow Error */
+#define IRQ_DMAR1_OVR		BFIN_IRQ(5)	/* DMAR1 Overflow Error */
+#define IRQ_PPI_ERROR		BFIN_IRQ(6)	/* PPI Error */
+#define IRQ_MAC_ERROR		BFIN_IRQ(7)	/* MAC Status */
+#define IRQ_SPORT0_ERROR	BFIN_IRQ(8)	/* SPORT0 Status */
+#define IRQ_SPORT1_ERROR	BFIN_IRQ(9)	/* SPORT1 Status */
+#define IRQ_UART0_ERROR		BFIN_IRQ(12)	/* UART0 Status */
+#define IRQ_UART1_ERROR		BFIN_IRQ(13)	/* UART1 Status */
+#define IRQ_RTC			BFIN_IRQ(14)	/* RTC */
+#define IRQ_PPI      		BFIN_IRQ(15)	/* DMA Channel 0 (PPI/NAND) */
+#define IRQ_SPORT0_RX		BFIN_IRQ(16)	/* DMA 3 Channel (SPORT0 RX) */
+#define IRQ_SPORT0_TX		BFIN_IRQ(17)	/* DMA 4 Channel (SPORT0 TX) */
+#define IRQ_SPORT1_RX		BFIN_IRQ(18)	/* DMA 5 Channel (SPORT1 RX) */
+#define IRQ_SPORT1_TX		BFIN_IRQ(19)	/* DMA 6 Channel (SPORT1 TX) */
+#define IRQ_TWI      		BFIN_IRQ(20)	/* TWI */
+#define IRQ_SPI      		BFIN_IRQ(21)	/* DMA 7 Channel (SPI) */
+#define IRQ_UART0_RX 		BFIN_IRQ(22)	/* DMA8 Channel (UART0 RX) */
+#define IRQ_UART0_TX 		BFIN_IRQ(23)	/* DMA9 Channel (UART0 TX) */
+#define IRQ_UART1_RX 		BFIN_IRQ(24)	/* DMA10 Channel (UART1 RX) */
+#define IRQ_UART1_TX 		BFIN_IRQ(25)	/* DMA11 Channel (UART1 TX) */
+#define IRQ_OPTSEC   		BFIN_IRQ(26)	/* OTPSEC Interrupt */
+#define IRQ_CNT   		BFIN_IRQ(27)	/* GP Counter */
+#define IRQ_MAC_RX   		BFIN_IRQ(28)	/* DMA1 Channel (MAC RX/HDMA) */
+#define IRQ_PORTH_INTA   	BFIN_IRQ(29)	/* Port H Interrupt A */
+#define IRQ_MAC_TX		BFIN_IRQ(30)	/* DMA2 Channel (MAC TX/NAND) */
+#define IRQ_NFC			BFIN_IRQ(30)	/* DMA2 Channel (MAC TX/NAND) */
+#define IRQ_PORTH_INTB		BFIN_IRQ(31)	/* Port H Interrupt B */
+#define IRQ_TMR0		BFIN_IRQ(32)	/* Timer 0 */
+#define IRQ_TMR1		BFIN_IRQ(33)	/* Timer 1 */
+#define IRQ_TMR2		BFIN_IRQ(34)	/* Timer 2 */
+#define IRQ_TMR3		BFIN_IRQ(35)	/* Timer 3 */
+#define IRQ_TMR4		BFIN_IRQ(36)	/* Timer 4 */
+#define IRQ_TMR5		BFIN_IRQ(37)	/* Timer 5 */
+#define IRQ_TMR6		BFIN_IRQ(38)	/* Timer 6 */
+#define IRQ_TMR7		BFIN_IRQ(39)	/* Timer 7 */
+#define IRQ_PORTG_INTA		BFIN_IRQ(40)	/* Port G Interrupt A */
+#define IRQ_PORTG_INTB		BFIN_IRQ(41)	/* Port G Interrupt B */
+#define IRQ_MEM_DMA0		BFIN_IRQ(42)	/* MDMA Stream 0 */
+#define IRQ_MEM_DMA1		BFIN_IRQ(43)	/* MDMA Stream 1 */
+#define IRQ_WATCH		BFIN_IRQ(44)	/* Software Watchdog Timer */
+#define IRQ_PORTF_INTA		BFIN_IRQ(45)	/* Port F Interrupt A */
+#define IRQ_PORTF_INTB		BFIN_IRQ(46)	/* Port F Interrupt B */
+#define IRQ_SPI_ERROR		BFIN_IRQ(47)	/* SPI Status */
+#define IRQ_NFC_ERROR		BFIN_IRQ(48)	/* NAND Error */
+#define IRQ_HDMA_ERROR		BFIN_IRQ(49)	/* HDMA Error */
+#define IRQ_HDMA		BFIN_IRQ(50)	/* HDMA (TFI) */
+#define IRQ_USB_EINT		BFIN_IRQ(51)	/* USB_EINT Interrupt */
+#define IRQ_USB_INT0		BFIN_IRQ(52)	/* USB_INT0 Interrupt */
+#define IRQ_USB_INT1		BFIN_IRQ(53)	/* USB_INT1 Interrupt */
+#define IRQ_USB_INT2		BFIN_IRQ(54)	/* USB_INT2 Interrupt */
+#define IRQ_USB_DMA		BFIN_IRQ(55)	/* USB_DMAINT Interrupt */
+
+#define SYS_IRQS        	BFIN_IRQ(63)	/* 70 */
+
+#define IRQ_PF0         71
+#define IRQ_PF1         72
+#define IRQ_PF2         73
+#define IRQ_PF3         74
+#define IRQ_PF4         75
+#define IRQ_PF5         76
+#define IRQ_PF6         77
+#define IRQ_PF7         78
+#define IRQ_PF8         79
+#define IRQ_PF9         80
+#define IRQ_PF10        81
+#define IRQ_PF11        82
+#define IRQ_PF12        83
+#define IRQ_PF13        84
+#define IRQ_PF14        85
+#define IRQ_PF15        86
+
+#define IRQ_PG0         87
+#define IRQ_PG1         88
+#define IRQ_PG2         89
+#define IRQ_PG3         90
+#define IRQ_PG4         91
+#define IRQ_PG5         92
+#define IRQ_PG6         93
+#define IRQ_PG7         94
+#define IRQ_PG8         95
+#define IRQ_PG9         96
+#define IRQ_PG10        97
+#define IRQ_PG11        98
+#define IRQ_PG12        99
+#define IRQ_PG13        100
+#define IRQ_PG14        101
+#define IRQ_PG15        102
+
+#define IRQ_PH0         103
+#define IRQ_PH1         104
+#define IRQ_PH2         105
+#define IRQ_PH3         106
+#define IRQ_PH4         107
+#define IRQ_PH5         108
+#define IRQ_PH6         109
+#define IRQ_PH7         110
+#define IRQ_PH8         111
+#define IRQ_PH9         112
+#define IRQ_PH10        113
+#define IRQ_PH11        114
+#define IRQ_PH12        115
+#define IRQ_PH13        116
+#define IRQ_PH14        117
+#define IRQ_PH15        118
+
+#define GPIO_IRQ_BASE	IRQ_PF0
+
+#define NR_IRQS     (IRQ_PH15+1)
+
+#define IVG7            7
+#define IVG8            8
+#define IVG9            9
+#define IVG10           10
+#define IVG11           11
+#define IVG12           12
+#define IVG13           13
+#define IVG14           14
+#define IVG15           15
+
+/* IAR0 BIT FIELDS */
+#define IRQ_PLL_WAKEUP_POS	0
+#define IRQ_DMA0_ERROR_POS	4
+#define IRQ_DMAR0_BLK_POS 	8
+#define IRQ_DMAR1_BLK_POS 	12
+#define IRQ_DMAR0_OVR_POS 	16
+#define IRQ_DMAR1_OVR_POS 	20
+#define IRQ_PPI_ERROR_POS 	24
+#define IRQ_MAC_ERROR_POS 	28
+
+/* IAR1 BIT FIELDS */
+#define IRQ_SPORT0_ERROR_POS	0
+#define IRQ_SPORT1_ERROR_POS	4
+#define IRQ_UART0_ERROR_POS 	16
+#define IRQ_UART1_ERROR_POS 	20
+#define IRQ_RTC_POS         	24
+#define IRQ_PPI_POS         	28
+
+/* IAR2 BIT FIELDS */
+#define IRQ_SPORT0_RX_POS	0
+#define IRQ_SPORT0_TX_POS	4
+#define IRQ_SPORT1_RX_POS	8
+#define IRQ_SPORT1_TX_POS	12
+#define IRQ_TWI_POS      	16
+#define IRQ_SPI_POS      	20
+#define IRQ_UART0_RX_POS 	24
+#define IRQ_UART0_TX_POS 	28
+
+/* IAR3 BIT FIELDS */
+#define IRQ_UART1_RX_POS  	0
+#define IRQ_UART1_TX_POS  	4
+#define IRQ_OPTSEC_POS    	8
+#define IRQ_CNT_POS       	12
+#define IRQ_MAC_RX_POS    	16
+#define IRQ_PORTH_INTA_POS	20
+#define IRQ_MAC_TX_POS    	24
+#define IRQ_PORTH_INTB_POS	28
+
+/* IAR4 BIT FIELDS */
+#define IRQ_TMR0_POS		0
+#define IRQ_TMR1_POS		4
+#define IRQ_TMR2_POS		8
+#define IRQ_TMR3_POS		12
+#define IRQ_TMR4_POS		16
+#define IRQ_TMR5_POS		20
+#define IRQ_TMR6_POS		24
+#define IRQ_TMR7_POS		28
+
+/* IAR5 BIT FIELDS */
+#define IRQ_PORTG_INTA_POS	0
+#define IRQ_PORTG_INTB_POS	4
+#define IRQ_MEM_DMA0_POS  	8
+#define IRQ_MEM_DMA1_POS  	12
+#define IRQ_WATCH_POS     	16
+#define IRQ_PORTF_INTA_POS	20
+#define IRQ_PORTF_INTB_POS	24
+#define IRQ_SPI_ERROR_POS 	28
+
+/* IAR6 BIT FIELDS */
+#define IRQ_NFC_ERROR_POS  	0
+#define IRQ_HDMA_ERROR_POS 	4
+#define IRQ_HDMA_POS       	8
+#define IRQ_USB_EINT_POS   	12
+#define IRQ_USB_INT0_POS   	16
+#define IRQ_USB_INT1_POS   	20
+#define IRQ_USB_INT2_POS   	24
+#define IRQ_USB_DMA_POS    	28
+
+#endif				/* _BF527_IRQ_H_ */
diff --git a/arch/blackfin/mach-bf527/include/mach/mem_init.h b/arch/blackfin/mach-bf527/include/mach/mem_init.h
new file mode 100644
index 00000000000..cbe03f4a569
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/mem_init.h
@@ -0,0 +1,310 @@
+/*
+ * File:         include/asm-blackfin/mach-bf527/mem_init.h
+ * Based on:
+ * Author:
+ *
+ * Created:
+ * Description:
+ *
+ * Rev:
+ *
+ * Modified:
+ *               Copyright 2004-2007 Analog Devices Inc.
+ *
+ * Bugs:         Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; see the file COPYING.
+ * If not, write to the Free Software Foundation,
+ * 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
+ */
+
+#if (CONFIG_MEM_MT48LC16M16A2TG_75 || CONFIG_MEM_MT48LC64M4A2FB_7E || CONFIG_MEM_MT48LC16M8A2TG_75 || CONFIG_MEM_GENERIC_BOARD || CONFIG_MEM_MT48LC32M8A2_75 || CONFIG_MEM_MT48LC32M16A2TG_75)
+#if (CONFIG_SCLK_HZ > 119402985)
+#define SDRAM_tRP       TRP_2
+#define SDRAM_tRP_num   2
+#define SDRAM_tRAS      TRAS_7
+#define SDRAM_tRAS_num  7
+#define SDRAM_tRCD      TRCD_2
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 104477612) && (CONFIG_SCLK_HZ <= 119402985)
+#define SDRAM_tRP       TRP_2
+#define SDRAM_tRP_num   2
+#define SDRAM_tRAS      TRAS_6
+#define SDRAM_tRAS_num  6
+#define SDRAM_tRCD      TRCD_2
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 89552239) && (CONFIG_SCLK_HZ <= 104477612)
+#define SDRAM_tRP       TRP_2
+#define SDRAM_tRP_num   2
+#define SDRAM_tRAS      TRAS_5
+#define SDRAM_tRAS_num  5
+#define SDRAM_tRCD      TRCD_2
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 74626866) && (CONFIG_SCLK_HZ <= 89552239)
+#define SDRAM_tRP       TRP_2
+#define SDRAM_tRP_num   2
+#define SDRAM_tRAS      TRAS_4
+#define SDRAM_tRAS_num  4
+#define SDRAM_tRCD      TRCD_2
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 66666667) && (CONFIG_SCLK_HZ <= 74626866)
+#define SDRAM_tRP       TRP_2
+#define SDRAM_tRP_num   2
+#define SDRAM_tRAS      TRAS_3
+#define SDRAM_tRAS_num  3
+#define SDRAM_tRCD      TRCD_2
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 59701493) && (CONFIG_SCLK_HZ <= 66666667)
+#define SDRAM_tRP       TRP_1
+#define SDRAM_tRP_num   1
+#define SDRAM_tRAS      TRAS_4
+#define SDRAM_tRAS_num  3
+#define SDRAM_tRCD      TRCD_1
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 44776119) && (CONFIG_SCLK_HZ <= 59701493)
+#define SDRAM_tRP       TRP_1
+#define SDRAM_tRP_num   1
+#define SDRAM_tRAS      TRAS_3
+#define SDRAM_tRAS_num  3
+#define SDRAM_tRCD      TRCD_1
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ > 29850746) && (CONFIG_SCLK_HZ <= 44776119)
+#define SDRAM_tRP       TRP_1
+#define SDRAM_tRP_num   1
+#define SDRAM_tRAS      TRAS_2
+#define SDRAM_tRAS_num  2
+#define SDRAM_tRCD      TRCD_1
+#define SDRAM_tWR       TWR_2
+#endif
+#if (CONFIG_SCLK_HZ <= 29850746)
+#define SDRAM_tRP       TRP_1
+#define SDRAM_tRP_num   1
+#define SDRAM_tRAS      TRAS_1
+#define SDRAM_tRAS_num  1
+#define SDRAM_tRCD      TRCD_1
+#define SDRAM_tWR       TWR_2
+#endif
+#endif
+
+#if (CONFIG_MEM_MT48LC16M16A2TG_75)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_MT48LC16M8A2TG_75)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   4096	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_MT48LC32M8A2_75)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_MT48LC64M4A2FB_7E)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_GENERIC_BOARD)
+  /*SDRAM INFORMATION: Modify this for your board */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+#if (CONFIG_MEM_MT48LC32M16A2TG_75)
+  /*SDRAM INFORMATION: */
+#define SDRAM_Tref  64		/* Refresh period in milliseconds   */
+#define SDRAM_NRA   8192	/* Number of row addresses in SDRAM */
+#define SDRAM_CL    CL_3
+#endif
+
+/* Equation from section 17 (p17-46) of BF533 HRM */
+#define mem_SDRRC       (((CONFIG_SCLK_HZ / 1000) * SDRAM_Tref) / SDRAM_NRA) - (SDRAM_tRAS_num + SDRAM_tRP_num)
+
+/* Enable SCLK Out */
+#define mem_SDGCTL        (SCTLE | SDRAM_CL | SDRAM_tRAS | SDRAM_tRP | SDRAM_tRCD | SDRAM_tWR | PSS)
+
+#if defined CONFIG_CLKIN_HALF
+#define CLKIN_HALF       1
+#else
+#define CLKIN_HALF       0
+#endif
+
+#if defined CONFIG_PLL_BYPASS
+#define PLL_BYPASS      1
+#else
+#define PLL_BYPASS       0
+#endif
+
+/***************************************Currently Not Being Used *********************************/
+#define flash_EBIU_AMBCTL_WAT  ((CONFIG_FLASH_SPEED_BWAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+#define flash_EBIU_AMBCTL_RAT  ((CONFIG_FLASH_SPEED_BRAT * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+#define flash_EBIU_AMBCTL_HT   ((CONFIG_FLASH_SPEED_BHT  * 4) / (4000000000 / CONFIG_SCLK_HZ))
+#define flash_EBIU_AMBCTL_ST   ((CONFIG_FLASH_SPEED_BST  * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+#define flash_EBIU_AMBCTL_TT   ((CONFIG_FLASH_SPEED_BTT  * 4) / (4000000000 / CONFIG_SCLK_HZ)) + 1
+
+#if (flash_EBIU_AMBCTL_TT > 3)
+#define flash_EBIU_AMBCTL0_TT   B0TT_4
+#endif
+#if (flash_EBIU_AMBCTL_TT == 3)
+#define flash_EBIU_AMBCTL0_TT   B0TT_3
+#endif
+#if (flash_EBIU_AMBCTL_TT == 2)
+#define flash_EBIU_AMBCTL0_TT   B0TT_2
+#endif
+#if (flash_EBIU_AMBCTL_TT < 2)
+#define flash_EBIU_AMBCTL0_TT   B0TT_1
+#endif
+
+#if (flash_EBIU_AMBCTL_ST > 3)
+#define flash_EBIU_AMBCTL0_ST   B0ST_4
+#endif
+#if (flash_EBIU_AMBCTL_ST == 3)
+#define flash_EBIU_AMBCTL0_ST   B0ST_3
+#endif
+#if (flash_EBIU_AMBCTL_ST == 2)
+#define flash_EBIU_AMBCTL0_ST   B0ST_2
+#endif
+#if (flash_EBIU_AMBCTL_ST < 2)
+#define flash_EBIU_AMBCTL0_ST   B0ST_1
+#endif
+
+#if (flash_EBIU_AMBCTL_HT > 2)
+#define flash_EBIU_AMBCTL0_HT   B0HT_3
+#endif
+#if (flash_EBIU_AMBCTL_HT == 2)
+#define flash_EBIU_AMBCTL0_HT   B0HT_2
+#endif
+#if (flash_EBIU_AMBCTL_HT == 1)
+#define flash_EBIU_AMBCTL0_HT   B0HT_1
+#endif
+#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT == 0)
+#define flash_EBIU_AMBCTL0_HT   B0HT_0
+#endif
+#if (flash_EBIU_AMBCTL_HT == 0 && CONFIG_FLASH_SPEED_BHT != 0)
+#define flash_EBIU_AMBCTL0_HT   B0HT_1
+#endif
+
+#if (flash_EBIU_AMBCTL_WAT > 14)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_15
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 14)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_14
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 13)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_13
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 12)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_12
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 11)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_11
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 10)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_10
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 9)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_9
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 8)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_8
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 7)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_7
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 6)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_6
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 5)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_5
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 4)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_4
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 3)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_3
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 2)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_2
+#endif
+#if (flash_EBIU_AMBCTL_WAT == 1)
+#define flash_EBIU_AMBCTL0_WAT  B0WAT_1
+#endif
+
+#if (flash_EBIU_AMBCTL_RAT > 14)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_15
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 14)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_14
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 13)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_13
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 12)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_12
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 11)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_11
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 10)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_10
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 9)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_9
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 8)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_8
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 7)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_7
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 6)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_6
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 5)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_5
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 4)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_4
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 3)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_3
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 2)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_2
+#endif
+#if (flash_EBIU_AMBCTL_RAT == 1)
+#define flash_EBIU_AMBCTL0_RAT  B0RAT_1
+#endif
+
+#define flash_EBIU_AMBCTL0  \
+	(flash_EBIU_AMBCTL0_WAT | flash_EBIU_AMBCTL0_RAT | flash_EBIU_AMBCTL0_HT | \
+	 flash_EBIU_AMBCTL0_ST | flash_EBIU_AMBCTL0_TT | CONFIG_FLASH_SPEED_RDYEN)
diff --git a/arch/blackfin/mach-bf527/include/mach/mem_map.h b/arch/blackfin/mach-bf527/include/mach/mem_map.h
new file mode 100644
index 00000000000..ef46dc991cd
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/mem_map.h
@@ -0,0 +1,102 @@
+/*
+ * file:         include/asm-blackfin/mach-bf527/mem_map.h
+ * based on:	include/asm-blackfin/mach-bf537/mem_map.h
+ * author:	Michael Hennerich (michael.hennerich@analog.com)
+ *
+ * created:
+ * description:
+ *	Memory MAP Common header file for blackfin BF527/5/2 of processors.
+ * rev:
+ *
+ * modified:
+ *
+ * bugs:         enter bugs at http://blackfin.uclinux.org/
+ *
+ * this program is free software; you can redistribute it and/or modify
+ * it under the terms of the gnu general public license as published by
+ * the free software foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * this program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * merchantability or fitness for a particular purpose.  see the
+ * gnu general public license for more details.
+ *
+ * you should have received a copy of the gnu general public license
+ * along with this program; see the file copying.
+ * if not, write to the free software foundation,
+ * 59 temple place - suite 330, boston, ma 02111-1307, usa.
+ */
+
+#ifndef _MEM_MAP_527_H_
+#define _MEM_MAP_527_H_
+
+#define COREMMR_BASE           0xFFE00000	/* Core MMRs */
+#define SYSMMR_BASE            0xFFC00000	/* System MMRs */
+
+/* Async Memory Banks */
+#define ASYNC_BANK3_BASE	0x20300000	/* Async Bank 3 */
+#define ASYNC_BANK3_SIZE	0x00100000	/* 1M */
+#define ASYNC_BANK2_BASE	0x20200000	/* Async Bank 2 */
+#define ASYNC_BANK2_SIZE	0x00100000	/* 1M */
+#define ASYNC_BANK1_BASE	0x20100000	/* Async Bank 1 */
+#define ASYNC_BANK1_SIZE	0x00100000	/* 1M */
+#define ASYNC_BANK0_BASE	0x20000000	/* Async Bank 0 */
+#define ASYNC_BANK0_SIZE	0x00100000	/* 1M */
+
+/* Boot ROM Memory */
+
+#define BOOT_ROM_START		0xEF000000
+#define BOOT_ROM_LENGTH		0x8000
+
+/* Level 1 Memory */
+
+/* Memory Map for ADSP-BF527 ADSP-BF525 ADSP-BF522 processors */
+
+#ifdef CONFIG_BFIN_ICACHE
+#define BFIN_ICACHESIZE	(16*1024)
+#else
+#define BFIN_ICACHESIZE	(0*1024)
+#endif
+
+#define L1_CODE_START       0xFFA00000
+#define L1_DATA_A_START     0xFF800000
+#define L1_DATA_B_START     0xFF900000
+
+#define L1_CODE_LENGTH      0xC000
+
+#ifdef CONFIG_BFIN_DCACHE
+
+#ifdef CONFIG_BFIN_DCACHE_BANKA
+#define DMEM_CNTR (ACACHE_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH      (0x8000 - 0x4000)
+#define L1_DATA_B_LENGTH      0x8000
+#define BFIN_DCACHESIZE	(16*1024)
+#define BFIN_DSUPBANKS	1
+#else
+#define DMEM_CNTR (ACACHE_BCACHE | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH      (0x8000 - 0x4000)
+#define L1_DATA_B_LENGTH      (0x8000 - 0x4000)
+#define BFIN_DCACHESIZE	(32*1024)
+#define BFIN_DSUPBANKS	2
+#endif
+
+#else
+#define DMEM_CNTR (ASRAM_BSRAM | ENDCPLB | PORT_PREF0)
+#define L1_DATA_A_LENGTH      0x8000
+#define L1_DATA_B_LENGTH      0x8000
+#define BFIN_DCACHESIZE	(0*1024)
+#define BFIN_DSUPBANKS	0
+#endif				/*CONFIG_BFIN_DCACHE */
+
+/* Level 2 Memory - none */
+
+#define L2_START	0
+#define L2_LENGTH	0
+
+/* Scratch Pad Memory */
+
+#define L1_SCRATCH_START	0xFFB00000
+#define L1_SCRATCH_LENGTH	0x1000
+
+#endif				/* _MEM_MAP_527_H_ */
diff --git a/arch/blackfin/mach-bf527/include/mach/portmux.h b/arch/blackfin/mach-bf527/include/mach/portmux.h
new file mode 100644
index 00000000000..ae4d205bfcf
--- /dev/null
+++ b/arch/blackfin/mach-bf527/include/mach/portmux.h
@@ -0,0 +1,207 @@
+#ifndef _MACH_PORTMUX_H_
+#define _MACH_PORTMUX_H_
+
+#define MAX_RESOURCES 	MAX_BLACKFIN_GPIOS
+
+#define P_PPI0_D0	(P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(0))
+#define P_PPI0_D1	(P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(0))
+#define P_PPI0_D2	(P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(0))
+#define P_PPI0_D3	(P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(0))
+#define P_PPI0_D4	(P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(0))
+#define P_PPI0_D5	(P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(0))
+#define P_PPI0_D6	(P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(0))
+#define P_PPI0_D7	(P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(0))
+#define P_PPI0_D8	(P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(0))
+#define P_PPI0_D9	(P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(0))
+#define P_PPI0_D10	(P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(0))
+#define P_PPI0_D11	(P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(0))
+#define P_PPI0_D12	(P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(0))
+#define P_PPI0_D13	(P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(0))
+#define P_PPI0_D14	(P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(0))
+#define P_PPI0_D15	(P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(0))
+
+#if defined(CONFIG_BF527_SPORT0_PORTF)
+#define P_SPORT0_DRPRI	(P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(1))
+#define P_SPORT0_RFS	(P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(1))
+#define P_SPORT0_RSCLK	(P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(1))
+#define P_SPORT0_DTPRI	(P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(1))
+#define P_SPORT0_TFS	(P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(1))
+#define P_SPORT0_TSCLK	(P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(1))
+#define P_SPORT0_DTSEC	(P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(1))
+#define P_SPORT0_DRSEC	(P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(1))
+#elif defined(CONFIG_BF527_SPORT0_PORTG)
+#define P_SPORT0_DTPRI	(P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(0))
+#define P_SPORT0_DRSEC	(P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(1))
+#define P_SPORT0_DTSEC	(P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(1))
+#define P_SPORT0_DRPRI	(P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(1))
+#define P_SPORT0_RFS	(P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(1))
+#define P_SPORT0_RSCLK	(P_DEFINED | P_IDENT(GPIO_PG9) | P_FUNCT(1))
+#if defined(CONFIG_BF527_SPORT0_TSCLK_PG10)
+#define P_SPORT0_TSCLK	(P_DEFINED | P_IDENT(GPIO_PG10) | P_FUNCT(1))
+#elif defined(CONFIG_BF527_SPORT0_TSCLK_PG14)
+#define P_SPORT0_TSCLK	(P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(0))
+#endif
+#define P_SPORT0_TFS	(P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(0))
+#endif
+
+#define P_SPORT1_DRPRI	(P_DEFINED | P_IDENT(GPIO_PF8) | P_FUNCT(1))
+#define P_SPORT1_RSCLK	(P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(1))
+#define P_SPORT1_RFS	(P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(1))
+#define P_SPORT1_TFS	(P_DEFINED | P_IDENT(GPIO_PF11) | P_FUNCT(1))
+#define P_SPORT1_DTPRI	(P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(1))
+#define P_SPORT1_TSCLK	(P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(1))
+#define P_SPORT1_DTSEC	(P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(1))
+#define P_SPORT1_DRSEC	(P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(1))
+
+#define P_SPI0_SSEL6	(P_DEFINED | P_IDENT(GPIO_PF9) | P_FUNCT(2))
+#define P_SPI0_SSEL7	(P_DEFINED | P_IDENT(GPIO_PF10) | P_FUNCT(2))
+
+#define P_SPI0_SSEL2	(P_DEFINED | P_IDENT(GPIO_PF12) | P_FUNCT(2))
+#define P_SPI0_SSEL3	(P_DEFINED | P_IDENT(GPIO_PF13) | P_FUNCT(2))
+
+#if defined(CONFIG_BF527_UART1_PORTF)
+#define P_UART1_TX	(P_DEFINED | P_IDENT(GPIO_PF14) | P_FUNCT(2))
+#define P_UART1_RX	(P_DEFINED | P_IDENT(GPIO_PF15) | P_FUNCT(2))
+#elif defined(CONFIG_BF527_UART1_PORTG)
+#define P_UART1_TX	(P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(1))
+#define P_UART1_RX	(P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(1))
+#endif
+
+#define P_HWAIT		(P_DONTCARE)
+
+#define P_SPI0_SS	(P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(0))
+#define P_SPI0_SSEL1	(P_DEFINED | P_IDENT(GPIO_PG1) | P_FUNCT(2))
+#define P_SPI0_SCK	(P_DEFINED | P_IDENT(GPIO_PG2) | P_FUNCT(2))
+#define P_SPI0_MISO	(P_DEFINED | P_IDENT(GPIO_PG3) | P_FUNCT(2))
+#define P_SPI0_MOSI	(P_DEFINED | P_IDENT(GPIO_PG4) | P_FUNCT(2))
+#define P_TMR1		(P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(0))
+#define P_PPI0_FS2	(P_DEFINED | P_IDENT(GPIO_PG5) | P_FUNCT(0))
+#define P_TMR3		(P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(0))
+#define P_TMR4		(P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(0))
+#define P_TMR5		(P_DEFINED | P_IDENT(GPIO_PG9) | P_FUNCT(0))
+#define P_TMR6		(P_DEFINED | P_IDENT(GPIO_PG10) | P_FUNCT(0))
+/* #define P_TMR7		(P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(0)) */
+#define P_DMAR1		(P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(0))
+#define P_DMAR0		(P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(0))
+#define P_TMR2		(P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(1))
+#define P_TMR7		(P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(1))
+#define P_MDC		(P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(1))
+#define P_RMII0_MDINT	(P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(1))
+#define P_MII0_PHYINT	(P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(1))
+
+#define P_PPI0_FS3	(P_DEFINED | P_IDENT(GPIO_PG6) | P_FUNCT(2))
+#define P_UART0_TX	(P_DEFINED | P_IDENT(GPIO_PG7) | P_FUNCT(2))
+#define P_UART0_RX	(P_DEFINED | P_IDENT(GPIO_PG8) | P_FUNCT(2))
+
+#define P_HOST_WR	(P_DEFINED | P_IDENT(GPIO_PG11) | P_FUNCT(2))
+#define P_HOST_ACK	(P_DEFINED | P_IDENT(GPIO_PG12) | P_FUNCT(2))
+#define P_HOST_ADDR	(P_DEFINED | P_IDENT(GPIO_PG13) | P_FUNCT(2))
+#define P_HOST_RD	(P_DEFINED | P_IDENT(GPIO_PG14) | P_FUNCT(2))
+#define P_HOST_CE	(P_DEFINED | P_IDENT(GPIO_PG15) | P_FUNCT(2))
+
+#if defined(CONFIG_BF527_NAND_D_PORTF)
+#define P_NAND_D0	(P_DEFINED | P_IDENT(GPIO_PF0) | P_FUNCT(2))
+#define P_NAND_D1	(P_DEFINED | P_IDENT(GPIO_PF1) | P_FUNCT(2))
+#define P_NAND_D2	(P_DEFINED | P_IDENT(GPIO_PF2) | P_FUNCT(2))
+#define P_NAND_D3	(P_DEFINED | P_IDENT(GPIO_PF3) | P_FUNCT(2))
+#define P_NAND_D4	(P_DEFINED | P_IDENT(GPIO_PF4) | P_FUNCT(2))
+#define P_NAND_D5	(P_DEFINED | P_IDENT(GPIO_PF5) | P_FUNCT(2))
+#define P_NAND_D6	(P_DEFINED | P_IDENT(GPIO_PF6) | P_FUNCT(2))
+#define P_NAND_D7	(P_DEFINED | P_IDENT(GPIO_PF7) | P_FUNCT(2))
+#elif defined(CONFIG_BF527_NAND_D_PORTH)
+#define P_NAND_D0	(P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(0))
+#define P_NAND_D1	(P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(0))
+#define P_NAND_D2	(P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(0))
+#define P_NAND_D3	(P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(0))
+#define P_NAND_D4	(P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(0))
+#define P_NAND_D5	(P_DEFINED | P_IDENT(GPIO_PH5) | P_FUNCT(0))
+#define P_NAND_D6	(P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(0))
+#define P_NAND_D7	(P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(0))
+#endif
+
+#define P_SPI0_SSEL4	(P_DEFINED | P_IDENT(GPIO_PH8) | P_FUNCT(0))
+#define P_SPI0_SSEL5	(P_DEFINED | P_IDENT(GPIO_PH9) | P_FUNCT(0))
+#define P_NAND_CE	(P_DEFINED | P_IDENT(GPIO_PH10) | P_FUNCT(0))
+#define P_NAND_WE	(P_DEFINED | P_IDENT(GPIO_PH11) | P_FUNCT(0))
+#define P_NAND_RE	(P_DEFINED | P_IDENT(GPIO_PH12) | P_FUNCT(0))
+#define P_NAND_RB	(P_DEFINED | P_IDENT(GPIO_PH13) | P_FUNCT(0))
+#define P_NAND_CLE	(P_DEFINED | P_IDENT(GPIO_PH14) | P_FUNCT(0))
+#define P_NAND_ALE	(P_DEFINED | P_IDENT(GPIO_PH15) | P_FUNCT(0))
+
+#define P_HOST_D0	(P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(2))
+#define P_HOST_D1	(P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(2))
+#define P_HOST_D2	(P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(2))
+#define P_HOST_D3	(P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(2))
+#define P_HOST_D4	(P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(2))
+#define P_HOST_D5	(P_DEFINED | P_IDENT(GPIO_PH5) | P_FUNCT(2))
+#define P_HOST_D6	(P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(2))
+#define P_HOST_D7	(P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(2))
+#define P_HOST_D8	(P_DEFINED | P_IDENT(GPIO_PH8) | P_FUNCT(2))
+#define P_HOST_D9	(P_DEFINED | P_IDENT(GPIO_PH9) | P_FUNCT(2))
+#define P_HOST_D10	(P_DEFINED | P_IDENT(GPIO_PH10) | P_FUNCT(2))
+#define P_HOST_D11	(P_DEFINED | P_IDENT(GPIO_PH11) | P_FUNCT(2))
+#define P_HOST_D12	(P_DEFINED | P_IDENT(GPIO_PH12) | P_FUNCT(2))
+#define P_HOST_D13	(P_DEFINED | P_IDENT(GPIO_PH13) | P_FUNCT(2))
+#define P_HOST_D14	(P_DEFINED | P_IDENT(GPIO_PH14) | P_FUNCT(2))
+#define P_HOST_D15	(P_DEFINED | P_IDENT(GPIO_PH15) | P_FUNCT(2))
+
+#define P_MII0_ETxD0	(P_DEFINED | P_IDENT(GPIO_PH5) | P_FUNCT(1))
+#define P_MII0_ETxD1	(P_DEFINED | P_IDENT(GPIO_PH7) | P_FUNCT(1))
+#define P_MII0_ETxD2	(P_DEFINED | P_IDENT(GPIO_PH9) | P_FUNCT(1))
+#define P_MII0_ETxD3	(P_DEFINED | P_IDENT(GPIO_PH11) | P_FUNCT(1))
+#define P_MII0_ETxEN	(P_DEFINED | P_IDENT(GPIO_PH3) | P_FUNCT(1))
+#define P_MII0_TxCLK	(P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(1))
+#define P_MII0_COL	(P_DEFINED | P_IDENT(GPIO_PH15) | P_FUNCT(1))
+#define P_MII0_ERxD0	(P_DEFINED | P_IDENT(GPIO_PH6) | P_FUNCT(1))
+#define P_MII0_ERxD1	(P_DEFINED | P_IDENT(GPIO_PH8) | P_FUNCT(1))
+#define P_MII0_ERxD2	(P_DEFINED | P_IDENT(GPIO_PH10) | P_FUNCT(1))
+#define P_MII0_ERxD3	(P_DEFINED | P_IDENT(GPIO_PH12) | P_FUNCT(1))
+#define P_MII0_ERxDV	(P_DEFINED | P_IDENT(GPIO_PH14) | P_FUNCT(1))
+#define P_MII0_ERxCLK	(P_DEFINED | P_IDENT(GPIO_PH13) | P_FUNCT(1))
+#define P_MII0_ERxER	(P_DEFINED | P_IDENT(GPIO_PH1) | P_FUNCT(1))
+#define P_MII0_CRS	(P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(1))
+#define P_RMII0_REF_CLK	(P_DEFINED | P_IDENT(GPIO_PH4) | P_FUNCT(1))
+#define P_RMII0_CRS_DV	(P_DEFINED | P_IDENT(GPIO_PH0) | P_FUNCT(1))
+#define P_MDIO		(P_DEFINED | P_IDENT(GPIO_PH2) | P_FUNCT(1))
+
+#define P_TWI0_SCL	(P_DONTCARE)
+#define P_TWI0_SDA	(P_DONTCARE)
+#define P_PPI0_FS1	(P_DONTCARE)
+#define P_TMR0		(P_DONTCARE)
+#define P_TMRCLK	(P_DONTCARE)
+#define P_PPI0_CLK	(P_DONTCARE)
+
+#define P_MII0 {\
+	P_MII0_ETxD0, \
+	P_MII0_ETxD1, \
+	P_MII0_ETxD2, \
+	P_MII0_ETxD3, \
+	P_MII0_ETxEN, \
+	P_MII0_TxCLK, \
+	P_MII0_PHYINT, \
+	P_MII0_COL, \
+	P_MII0_ERxD0, \
+	P_MII0_ERxD1, \
+	P_MII0_ERxD2, \
+	P_MII0_ERxD3, \
+	P_MII0_ERxDV, \
+	P_MII0_ERxCLK, \
+	P_MII0_ERxER, \
+	P_MII0_CRS, \
+	P_MDC, \
+	P_MDIO, 0}
+
+#define P_RMII0 {\
+	P_MII0_ETxD0, \
+	P_MII0_ETxD1, \
+	P_MII0_ETxEN, \
+	P_MII0_ERxD0, \
+	P_MII0_ERxD1, \
+	P_MII0_ERxER, \
+	P_RMII0_REF_CLK, \
+	P_RMII0_MDINT, \
+	P_RMII0_CRS_DV, \
+	P_MDC, \
+	P_MDIO, 0}
+
+#endif				/* _MACH_PORTMUX_H_ */