Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
  omap: complete removal of machine_desc.io_pg_offst and .phys_io
  omap: UART: fix wakeup registers for OMAP24xx UART2
  omap: Fix spotty MMC voltages
  ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
  serial: omap-serial: fix signess error
  OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
  omap: dma: Fix buffering disable bit setting for omap24xx
  omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
  OMAP3: PM: fix scratchpad memory accesses for off-mode
  omap4: pandaboard: enable the ehci port on pandaboard
  omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
  omap4: pandaboard: remove unused hsmmc definition
  OMAP: McBSP: Remove null omap44xx ops comment
  OMAP: McBSP: Swap CLKS source definition
  OMAP: McBSP: Fix CLKR and FSR signal muxing
  OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
  OMAP: control: move plat-omap/control.h to mach-omap2/control.h
  OMAP: split plat-omap/common.c
  OMAP: McBSP: implement functional clock switching via clock framework
  OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
  ...

Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony

1 files changed, 128 insertions, 0 deletions

diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
new file mode 100644
index 00000000000..c8dae02f070
--- /dev/null
+++ b/arch/arm/plat-omap/include/plat/omap-serial.h
@@ -0,0 +1,128 @@
+/*
+ * Driver for OMAP-UART controller.
+ * Based on drivers/serial/8250.c
+ *
+ * Copyright (C) 2010 Texas Instruments.
+ *
+ * Authors:
+ *	Govindraj R	<govindraj.raja@ti.com>
+ *	Thara Gopinath	<thara@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef __OMAP_SERIAL_H__
+#define __OMAP_SERIAL_H__
+
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+
+#include <plat/mux.h>
+
+#define DRIVER_NAME	"omap-hsuart"
+
+/*
+ * Use tty device name as ttyO, [O -> OMAP]
+ * in bootargs we specify as console=ttyO0 if uart1
+ * is used as console uart.
+ */
+#define OMAP_SERIAL_NAME	"ttyO"
+
+#define OMAP_MDR1_DISABLE	0x07
+#define OMAP_MDR1_MODE13X	0x03
+#define OMAP_MDR1_MODE16X	0x00
+#define OMAP_MODE13X_SPEED	230400
+
+/*
+ * LCR = 0XBF: Switch to Configuration Mode B.
+ * In configuration mode b allow access
+ * to EFR,DLL,DLH.
+ * Reference OMAP TRM Chapter 17
+ * Section: 1.4.3 Mode Selection
+ */
+#define OMAP_UART_LCR_CONF_MDB	0XBF
+
+/* WER = 0x7F
+ * Enable module level wakeup in WER reg
+ */
+#define OMAP_UART_WER_MOD_WKUP	0X7F
+
+/* Enable XON/XOFF flow control on output */
+#define OMAP_UART_SW_TX		0x04
+
+/* Enable XON/XOFF flow control on input */
+#define OMAP_UART_SW_RX		0x04
+
+#define OMAP_UART_SYSC_RESET	0X07
+#define OMAP_UART_TCR_TRIG	0X0F
+#define OMAP_UART_SW_CLR	0XF0
+#define OMAP_UART_FIFO_CLR	0X06
+
+#define OMAP_UART_DMA_CH_FREE	-1
+
+#define RX_TIMEOUT		(3 * HZ)
+#define OMAP_MAX_HSUART_PORTS	4
+
+#define MSR_SAVE_FLAGS		UART_MSR_ANY_DELTA
+
+struct omap_uart_port_info {
+	bool			dma_enabled;	/* To specify DMA Mode */
+	unsigned int		uartclk;	/* UART clock rate */
+	void __iomem		*membase;	/* ioremap cookie or NULL */
+	resource_size_t		mapbase;	/* resource base */
+	unsigned long		irqflags;	/* request_irq flags */
+	upf_t			flags;		/* UPF_* flags */
+};
+
+struct uart_omap_dma {
+	u8			uart_dma_tx;
+	u8			uart_dma_rx;
+	int			rx_dma_channel;
+	int			tx_dma_channel;
+	dma_addr_t		rx_buf_dma_phys;
+	dma_addr_t		tx_buf_dma_phys;
+	unsigned int		uart_base;
+	/*
+	 * Buffer for rx dma.It is not required for tx because the buffer
+	 * comes from port structure.
+	 */
+	unsigned char		*rx_buf;
+	unsigned int		prev_rx_dma_pos;
+	int			tx_buf_size;
+	int			tx_dma_used;
+	int			rx_dma_used;
+	spinlock_t		tx_lock;
+	spinlock_t		rx_lock;
+	/* timer to poll activity on rx dma */
+	struct timer_list	rx_timer;
+	int			rx_buf_size;
+	int			rx_timeout;
+};
+
+struct uart_omap_port {
+	struct uart_port	port;
+	struct uart_omap_dma	uart_dma;
+	struct platform_device	*pdev;
+
+	unsigned char		ier;
+	unsigned char		lcr;
+	unsigned char		mcr;
+	unsigned char		fcr;
+	unsigned char		efr;
+
+	int			use_dma;
+	/*
+	 * Some bits in registers are cleared on a read, so they must
+	 * be saved whenever the register is read but the bits will not
+	 * be immediately processed.
+	 */
+	unsigned int		lsr_break_flag;
+	unsigned char		msr_saved_flags;
+	char			name[20];
+	unsigned long		port_activity;
+};
+
+#endif /* __OMAP_SERIAL_H__ */