Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm soc-specific pinctrl changes from Olof Johansson:
 "With this, five platforms are moving to the relatively new pinctrl
  subsystem for their pin management, replacing the older soc specific
  in-kernel interfaces with common code.

  There is quite a bit of net addition of code for each platform being
  added to the pinctrl subsystem.  But the payback comes later when
  adding new boards can be done by only providing new device trees
  instead."

Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}

* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
  mtd: nand: gpmi: fix compile error caused by pinctrl call
  ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
  ARM: nomadik: enable PINCTRL_NOMADIK where needed
  ARM: mxs: enable pinctrl support
  video: mxsfb: adopt pinctrl support
  ASoC: mxs-saif: adopt pinctrl support
  i2c: mxs: adopt pinctrl support
  mtd: nand: gpmi: adopt pinctrl support
  mmc: mxs-mmc: adopt pinctrl support
  serial: mxs-auart: adopt pinctrl support
  serial: amba-pl011: adopt pinctrl support
  spi/imx: adopt pinctrl support
  i2c: imx: adopt pinctrl support
  can: flexcan: adopt pinctrl support
  net: fec: adopt pinctrl support
  ARM: ux500: switch MSP to using pinctrl for pins
  ARM: ux500: alter MSP registration to return a device pointer
  ARM: ux500: switch to using pinctrl for uart0
  ARM: ux500: delete custom pin control system
  ARM: ux500: switch over to Nomadik pinctrl driver
  ...

14 files changed, 928 insertions, 345 deletions

diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index 0e8470a3fbe..53d3d46dec1 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -9,6 +9,8 @@ config UX500_SOC_COMMON
 	select ARM_ERRATA_754322
 	select ARM_ERRATA_764369
 	select CACHE_L2X0
+	select PINCTRL
+	select PINCTRL_NOMADIK
 
 config UX500_SOC_DB8500
 	bool
@@ -16,6 +18,7 @@ config UX500_SOC_DB8500
 	select REGULATOR
 	select REGULATOR_DB8500_PRCMU
 	select CPU_FREQ_TABLE if CPU_FREQ
+	select PINCTRL_DB8500
 
 menu "Ux500 target platform (boards)"
 
diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile
index fc7db5df970..041c3588598 100644
--- a/arch/arm/mach-ux500/Makefile
+++ b/arch/arm/mach-ux500/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_MACH_MOP500)	+= board-mop500.o board-mop500-sdi.o \
 				board-mop500-regulators.o \
 				board-mop500-uib.o board-mop500-stuib.o \
 				board-mop500-u8500uib.o \
-				board-mop500-pins.o
+				board-mop500-pins.o \
+				board-mop500-msp.o
 obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)	+= hotplug.o
diff --git a/arch/arm/mach-ux500/board-mop500-msp.c b/arch/arm/mach-ux500/board-mop500-msp.c
new file mode 100644
index 00000000000..99604803874
--- /dev/null
+++ b/arch/arm/mach-ux500/board-mop500-msp.c
@@ -0,0 +1,267 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2010
+ *
+ * License terms: GNU General Public License (GPL), version 2
+ */
+
+#include <linux/platform_device.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/pinctrl/consumer.h>
+
+#include <plat/gpio-nomadik.h>
+#include <plat/pincfg.h>
+#include <plat/ste_dma40.h>
+
+#include <mach/devices.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <mach/msp.h>
+
+#include "ste-dma40-db8500.h"
+#include "board-mop500.h"
+#include "devices-db8500.h"
+#include "pins-db8500.h"
+
+/* MSP1/3 Tx/Rx usage protection */
+static DEFINE_SPINLOCK(msp_rxtx_lock);
+
+/* Reference Count */
+static int msp_rxtx_ref;
+
+/* Pin modes */
+struct pinctrl *msp1_p;
+struct pinctrl_state *msp1_def;
+struct pinctrl_state *msp1_sleep;
+
+int msp13_i2s_init(void)
+{
+	int retval = 0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&msp_rxtx_lock, flags);
+	if (msp_rxtx_ref == 0 && !(IS_ERR(msp1_p) || IS_ERR(msp1_def))) {
+		retval = pinctrl_select_state(msp1_p, msp1_def);
+		if (retval)
+			pr_err("could not set MSP1 defstate\n");
+	}
+	if (!retval)
+		msp_rxtx_ref++;
+	spin_unlock_irqrestore(&msp_rxtx_lock, flags);
+
+	return retval;
+}
+
+int msp13_i2s_exit(void)
+{
+	int retval = 0;
+	unsigned long flags;
+
+	spin_lock_irqsave(&msp_rxtx_lock, flags);
+	WARN_ON(!msp_rxtx_ref);
+	msp_rxtx_ref--;
+	if (msp_rxtx_ref == 0 && !(IS_ERR(msp1_p) || IS_ERR(msp1_sleep))) {
+		retval = pinctrl_select_state(msp1_p, msp1_sleep);
+		if (retval)
+			pr_err("could not set MSP1 sleepstate\n");
+	}
+	spin_unlock_irqrestore(&msp_rxtx_lock, flags);
+
+	return retval;
+}
+
+static struct stedma40_chan_cfg msp0_dma_rx = {
+	.high_priority = true,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+
+	.src_dev_type = DB8500_DMA_DEV31_MSP0_RX_SLIM0_CH0_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+
+	.src_info.psize = STEDMA40_PSIZE_LOG_4,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_4,
+
+	/* data_width is set during configuration */
+};
+
+static struct stedma40_chan_cfg msp0_dma_tx = {
+	.high_priority = true,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+
+	.src_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV31_MSP0_TX_SLIM0_CH0_TX,
+
+	.src_info.psize = STEDMA40_PSIZE_LOG_4,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_4,
+
+	/* data_width is set during configuration */
+};
+
+static struct msp_i2s_platform_data msp0_platform_data = {
+	.id = MSP_I2S_0,
+	.msp_i2s_dma_rx = &msp0_dma_rx,
+	.msp_i2s_dma_tx = &msp0_dma_tx,
+};
+
+static struct stedma40_chan_cfg msp1_dma_rx = {
+	.high_priority = true,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+
+	.src_dev_type = DB8500_DMA_DEV30_MSP3_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+
+	.src_info.psize = STEDMA40_PSIZE_LOG_4,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_4,
+
+	/* data_width is set during configuration */
+};
+
+static struct stedma40_chan_cfg msp1_dma_tx = {
+	.high_priority = true,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+
+	.src_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV30_MSP1_TX,
+
+	.src_info.psize = STEDMA40_PSIZE_LOG_4,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_4,
+
+	/* data_width is set during configuration */
+};
+
+static struct msp_i2s_platform_data msp1_platform_data = {
+	.id = MSP_I2S_1,
+	.msp_i2s_dma_rx = NULL,
+	.msp_i2s_dma_tx = &msp1_dma_tx,
+	.msp_i2s_init = msp13_i2s_init,
+	.msp_i2s_exit = msp13_i2s_exit,
+};
+
+static struct stedma40_chan_cfg msp2_dma_rx = {
+	.high_priority = true,
+	.dir = STEDMA40_PERIPH_TO_MEM,
+
+	.src_dev_type = DB8500_DMA_DEV14_MSP2_RX,
+	.dst_dev_type = STEDMA40_DEV_DST_MEMORY,
+
+	/* MSP2 DMA doesn't work with PSIZE == 4 on DB8500v2 */
+	.src_info.psize = STEDMA40_PSIZE_LOG_1,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_1,
+
+	/* data_width is set during configuration */
+};
+
+static struct stedma40_chan_cfg msp2_dma_tx = {
+	.high_priority = true,
+	.dir = STEDMA40_MEM_TO_PERIPH,
+
+	.src_dev_type = STEDMA40_DEV_DST_MEMORY,
+	.dst_dev_type = DB8500_DMA_DEV14_MSP2_TX,
+
+	.src_info.psize = STEDMA40_PSIZE_LOG_4,
+	.dst_info.psize = STEDMA40_PSIZE_LOG_4,
+
+	.use_fixed_channel = true,
+	.phy_channel = 1,
+
+	/* data_width is set during configuration */
+};
+
+static struct platform_device *db8500_add_msp_i2s(struct device *parent,
+			int id,
+			resource_size_t base, int irq,
+			struct msp_i2s_platform_data *pdata)
+{
+	struct platform_device *pdev;
+	struct resource res[] = {
+		DEFINE_RES_MEM(base, SZ_4K),
+		DEFINE_RES_IRQ(irq),
+	};
+
+	pr_info("Register platform-device 'ux500-msp-i2s', id %d, irq %d\n",
+		id, irq);
+	pdev = platform_device_register_resndata(parent, "ux500-msp-i2s", id,
+						res, ARRAY_SIZE(res),
+						pdata, sizeof(*pdata));
+	if (!pdev) {
+		pr_err("Failed to register platform-device 'ux500-msp-i2s.%d'!\n",
+			id);
+		return NULL;
+	}
+
+	return pdev;
+}
+
+/* Platform device for ASoC U8500 machine */
+static struct platform_device snd_soc_u8500 = {
+		.name = "snd-soc-u8500",
+		.id = 0,
+		.dev = {
+			.platform_data = NULL,
+		},
+};
+
+/* Platform device for Ux500-PCM */
+static struct platform_device ux500_pcm = {
+		.name = "ux500-pcm",
+		.id = 0,
+		.dev = {
+			.platform_data = NULL,
+		},
+};
+
+static struct msp_i2s_platform_data msp2_platform_data = {
+	.id = MSP_I2S_2,
+	.msp_i2s_dma_rx = &msp2_dma_rx,
+	.msp_i2s_dma_tx = &msp2_dma_tx,
+};
+
+static struct msp_i2s_platform_data msp3_platform_data = {
+	.id		= MSP_I2S_3,
+	.msp_i2s_dma_rx	= &msp1_dma_rx,
+	.msp_i2s_dma_tx	= NULL,
+	.msp_i2s_init = msp13_i2s_init,
+	.msp_i2s_exit = msp13_i2s_exit,
+};
+
+int mop500_msp_init(struct device *parent)
+{
+	struct platform_device *msp1;
+
+	pr_info("%s: Register platform-device 'snd-soc-u8500'.\n", __func__);
+	platform_device_register(&snd_soc_u8500);
+
+	pr_info("Initialize MSP I2S-devices.\n");
+	db8500_add_msp_i2s(parent, 0, U8500_MSP0_BASE, IRQ_DB8500_MSP0,
+			   &msp0_platform_data);
+	msp1 = db8500_add_msp_i2s(parent, 1, U8500_MSP1_BASE, IRQ_DB8500_MSP1,
+			   &msp1_platform_data);
+	db8500_add_msp_i2s(parent, 2, U8500_MSP2_BASE, IRQ_DB8500_MSP2,
+			   &msp2_platform_data);
+	db8500_add_msp_i2s(parent, 3, U8500_MSP3_BASE, IRQ_DB8500_MSP1,
+			   &msp3_platform_data);
+
+	/* Get the pinctrl handle for MSP1 */
+	if (msp1) {
+		msp1_p = pinctrl_get(&msp1->dev);
+		if (IS_ERR(msp1_p))
+			dev_err(&msp1->dev, "could not get MSP1 pinctrl\n");
+		else {
+			msp1_def = pinctrl_lookup_state(msp1_p,
+							PINCTRL_STATE_DEFAULT);
+			if (IS_ERR(msp1_def)) {
+				dev_err(&msp1->dev,
+					"could not get MSP1 defstate\n");
+			}
+			msp1_sleep = pinctrl_lookup_state(msp1_p,
+							  PINCTRL_STATE_SLEEP);
+			if (IS_ERR(msp1_sleep))
+				dev_err(&msp1->dev,
+					"could not get MSP1 idlestate\n");
+		}
+	}
+
+	pr_info("%s: Register platform-device 'ux500-pcm'\n", __func__);
+	platform_device_register(&ux500_pcm);
+
+	return 0;
+}
diff --git a/arch/arm/mach-ux500/board-mop500-msp.h b/arch/arm/mach-ux500/board-mop500-msp.h
new file mode 100644
index 00000000000..6fcfb5e2cc9
--- /dev/null
+++ b/arch/arm/mach-ux500/board-mop500-msp.h
@@ -0,0 +1,14 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2012
+ *
+ * Author: Ola Lilja <ola.o.lilja@stericsson.com>,
+ *         for ST-Ericsson.
+ *
+ * License terms:
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+void mop500_msp_init(struct device *parent);
diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c
index f5413dca532..32fd9920446 100644
--- a/arch/arm/mach-ux500/board-mop500-pins.c
+++ b/arch/arm/mach-ux500/board-mop500-pins.c
@@ -7,299 +7,508 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/bug.h>
+#include <linux/string.h>
+#include <linux/pinctrl/machine.h>
 
 #include <asm/mach-types.h>
 #include <plat/pincfg.h>
 #include <plat/gpio-nomadik.h>
+
 #include <mach/hardware.h>
 
 #include "pins-db8500.h"
+#include "board-mop500.h"
 
-static pin_cfg_t mop500_pins_common[] = {
-	/* I2C */
-	GPIO147_I2C0_SCL,
-	GPIO148_I2C0_SDA,
-	GPIO16_I2C1_SCL,
-	GPIO17_I2C1_SDA,
-	GPIO10_I2C2_SDA,
-	GPIO11_I2C2_SCL,
-	GPIO229_I2C3_SDA,
-	GPIO230_I2C3_SCL,
-
-	/* MSP0 */
-	GPIO12_MSP0_TXD,
-	GPIO13_MSP0_TFS,
-	GPIO14_MSP0_TCK,
-	GPIO15_MSP0_RXD,
-
-	/* MSP2: HDMI */
-	GPIO193_MSP2_TXD,
-	GPIO194_MSP2_TCK,
-	GPIO195_MSP2_TFS,
-	GPIO196_MSP2_RXD | PIN_OUTPUT_LOW,
-
-	/* Touch screen INTERFACE */
-	GPIO84_GPIO	| PIN_INPUT_PULLUP, /* TOUCH_INT1 */
-
-	/* STMPE1601/tc35893 keypad  IRQ */
-	GPIO218_GPIO	| PIN_INPUT_PULLUP,
-
-	/* MMC0 (MicroSD card) */
-	GPIO18_MC0_CMDDIR	| PIN_OUTPUT_HIGH,
-	GPIO19_MC0_DAT0DIR	| PIN_OUTPUT_HIGH,
-	GPIO20_MC0_DAT2DIR	| PIN_OUTPUT_HIGH,
-
-	GPIO22_MC0_FBCLK	| PIN_INPUT_NOPULL,
-	GPIO23_MC0_CLK		| PIN_OUTPUT_LOW,
-	GPIO24_MC0_CMD		| PIN_INPUT_PULLUP,
-	GPIO25_MC0_DAT0		| PIN_INPUT_PULLUP,
-	GPIO26_MC0_DAT1		| PIN_INPUT_PULLUP,
-	GPIO27_MC0_DAT2		| PIN_INPUT_PULLUP,
-	GPIO28_MC0_DAT3		| PIN_INPUT_PULLUP,
-
-	/* SDI1 (SDIO) */
-	GPIO208_MC1_CLK		| PIN_OUTPUT_LOW,
-	GPIO209_MC1_FBCLK	| PIN_INPUT_NOPULL,
-	GPIO210_MC1_CMD		| PIN_INPUT_PULLUP,
-	GPIO211_MC1_DAT0	| PIN_INPUT_PULLUP,
-	GPIO212_MC1_DAT1	| PIN_INPUT_PULLUP,
-	GPIO213_MC1_DAT2	| PIN_INPUT_PULLUP,
-	GPIO214_MC1_DAT3	| PIN_INPUT_PULLUP,
-
-	/* MMC2 (On-board DATA INTERFACE eMMC) */
-	GPIO128_MC2_CLK		| PIN_OUTPUT_LOW,
-	GPIO129_MC2_CMD		| PIN_INPUT_PULLUP,
-	GPIO130_MC2_FBCLK	| PIN_INPUT_NOPULL,
-	GPIO131_MC2_DAT0	| PIN_INPUT_PULLUP,
-	GPIO132_MC2_DAT1	| PIN_INPUT_PULLUP,
-	GPIO133_MC2_DAT2	| PIN_INPUT_PULLUP,
-	GPIO134_MC2_DAT3	| PIN_INPUT_PULLUP,
-	GPIO135_MC2_DAT4	| PIN_INPUT_PULLUP,
-	GPIO136_MC2_DAT5	| PIN_INPUT_PULLUP,
-	GPIO137_MC2_DAT6	| PIN_INPUT_PULLUP,
-	GPIO138_MC2_DAT7	| PIN_INPUT_PULLUP,
-
-	/* MMC4 (On-board STORAGE INTERFACE eMMC) */
-	GPIO197_MC4_DAT3	| PIN_INPUT_PULLUP,
-	GPIO198_MC4_DAT2	| PIN_INPUT_PULLUP,
-	GPIO199_MC4_DAT1	| PIN_INPUT_PULLUP,
-	GPIO200_MC4_DAT0	| PIN_INPUT_PULLUP,
-	GPIO201_MC4_CMD		| PIN_INPUT_PULLUP,
-	GPIO202_MC4_FBCLK	| PIN_INPUT_NOPULL,
-	GPIO203_MC4_CLK		| PIN_OUTPUT_LOW,
-	GPIO204_MC4_DAT7	| PIN_INPUT_PULLUP,
-	GPIO205_MC4_DAT6	| PIN_INPUT_PULLUP,
-	GPIO206_MC4_DAT5	| PIN_INPUT_PULLUP,
-	GPIO207_MC4_DAT4	| PIN_INPUT_PULLUP,
-
-	/* SKE keypad */
-	GPIO153_KP_I7,
-	GPIO154_KP_I6,
-	GPIO155_KP_I5,
-	GPIO156_KP_I4,
-	GPIO157_KP_O7,
-	GPIO158_KP_O6,
-	GPIO159_KP_O5,
-	GPIO160_KP_O4,
-	GPIO161_KP_I3,
-	GPIO162_KP_I2,
-	GPIO163_KP_I1,
-	GPIO164_KP_I0,
-	GPIO165_KP_O3,
-	GPIO166_KP_O2,
-	GPIO167_KP_O1,
-	GPIO168_KP_O0,
+enum custom_pin_cfg_t {
+	PINS_FOR_DEFAULT,
+	PINS_FOR_U9500,
+};
 
-	/* UART */
-	/* uart-0 pins gpio configuration should be
-	 * kept intact to prevent glitch in tx line
-	 * when tty dev is opened. Later these pins
+static enum custom_pin_cfg_t pinsfor;
+
+/* These simply sets bias for pins */
+#define BIAS(a,b) static unsigned long a[] = { b }
+
+BIAS(pd, PIN_PULL_DOWN);
+BIAS(slpm_gpio_nopull, PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
+BIAS(in_nopull, PIN_INPUT_NOPULL);
+BIAS(in_nopull_sleep_nowkup, PIN_INPUT_NOPULL|PIN_SLPM_WAKEUP_DISABLE);
+BIAS(in_pu, PIN_INPUT_PULLUP);
+BIAS(in_pd, PIN_INPUT_PULLDOWN);
+BIAS(in_pd_slpm_in_pu, PIN_INPUT_PULLDOWN|PIN_SLPM_INPUT_PULLUP);
+BIAS(in_pu_slpm_out_lo, PIN_INPUT_PULLUP|PIN_SLPM_OUTPUT_LOW);
+BIAS(out_hi, PIN_OUTPUT_HIGH);
+BIAS(out_lo, PIN_OUTPUT_LOW);
+BIAS(out_lo_sleep_nowkup, PIN_OUTPUT_LOW|PIN_SLPM_WAKEUP_DISABLE);
+/* These also force them into GPIO mode */
+BIAS(gpio_in_pu, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED);
+BIAS(gpio_in_pd, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED);
+BIAS(gpio_in_pu_slpm_gpio_nopull, PIN_INPUT_PULLUP|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
+BIAS(gpio_in_pd_slpm_gpio_nopull, PIN_INPUT_PULLDOWN|PIN_GPIOMODE_ENABLED|PIN_SLPM_GPIO|PIN_SLPM_INPUT_NOPULL);
+BIAS(gpio_out_hi, PIN_OUTPUT_HIGH|PIN_GPIOMODE_ENABLED);
+BIAS(gpio_out_lo, PIN_OUTPUT_LOW|PIN_GPIOMODE_ENABLED);
+/* Sleep modes */
+BIAS(sleep_in_wkup_pdis, PIN_SLPM_DIR_INPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
+BIAS(sleep_in_nopull_wkup, PIN_INPUT_NOPULL|PIN_SLPM_WAKEUP_ENABLE);
+BIAS(sleep_out_hi_wkup_pdis, PIN_SLPM_OUTPUT_HIGH|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
+BIAS(sleep_out_lo_wkup, PIN_OUTPUT_LOW|PIN_SLPM_WAKEUP_ENABLE);
+BIAS(sleep_out_wkup_pdis, PIN_SLPM_DIR_OUTPUT|PIN_SLPM_WAKEUP_ENABLE|PIN_SLPM_PDIS_DISABLED);
+
+/* We use these to define hog settings that are always done on boot */
+#define DB8500_MUX_HOG(group,func) \
+	PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-db8500", group, func)
+#define DB8500_PIN_HOG(pin,conf) \
+	PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-db8500", pin, conf)
+
+/* These are default states associated with device and changed runtime */
+#define DB8500_MUX(group,func,dev) \
+	PIN_MAP_MUX_GROUP_DEFAULT(dev, "pinctrl-db8500", group, func)
+#define DB8500_PIN(pin,conf,dev) \
+	PIN_MAP_CONFIGS_PIN_DEFAULT(dev, "pinctrl-db8500", pin, conf)
+
+#define DB8500_PIN_SLEEP(pin,conf,dev) \
+	PIN_MAP_CONFIGS_PIN(dev, PINCTRL_STATE_SLEEP, "pinctrl-db8500",	\
+			    pin, conf)
+
+/* Pin control settings */
+static struct pinctrl_map __initdata mop500_family_pinmap[] = {
+	/*
+	 * uMSP0, mux in 4 pins, regular placement of RX/TX
+	 * explicitly set the pins to no pull
+	 */
+	DB8500_MUX_HOG("msp0txrx_a_1", "msp0"),
+	DB8500_MUX_HOG("msp0tfstck_a_1", "msp0"),
+	DB8500_PIN_HOG("GPIO12_AC4", in_nopull), /* TXD */
+	DB8500_PIN_HOG("GPIO15_AC3", in_nopull), /* RXD */
+	DB8500_PIN_HOG("GPIO13_AF3", in_nopull), /* TFS */
+	DB8500_PIN_HOG("GPIO14_AE3", in_nopull), /* TCK */
+	/* MSP2 for HDMI, pull down TXD, TCK, TFS  */
+	DB8500_MUX_HOG("msp2_a_1", "msp2"),
+	DB8500_PIN_HOG("GPIO193_AH27", in_pd), /* TXD */
+	DB8500_PIN_HOG("GPIO194_AF27", in_pd), /* TCK */
+	DB8500_PIN_HOG("GPIO195_AG28", in_pd), /* TFS */
+	DB8500_PIN_HOG("GPIO196_AG26", out_lo), /* RXD */
+	/*
+	 * LCD, set TE0 (using LCD VSI0) and D14 (touch screen interrupt) to
+	 * pull-up
+	 * TODO: is this really correct? Snowball doesn't have a LCD.
+	 */
+	DB8500_MUX_HOG("lcdvsi0_a_1", "lcd"),
+	DB8500_PIN_HOG("GPIO68_E1", in_pu),
+	DB8500_PIN_HOG("GPIO84_C2", gpio_in_pu),
+	/*
+	 * STMPE1601/tc35893 keypad IRQ GPIO 218
+	 * TODO: set for snowball and HREF really??
+	 */
+	DB8500_PIN_HOG("GPIO218_AH11", gpio_in_pu),
+	/*
+	 * UART0, we do not mux in u0 here.
+	 * uart-0 pins gpio configuration should be kept intact to prevent
+	 * a glitch in tx line when the tty dev is opened. Later these pins
 	 * are configured to uart mop500_pins_uart0
-	 *
-	 * It will be replaced with uart configuration
-	 * once the issue is solved.
 	 */
-	GPIO0_GPIO	| PIN_INPUT_PULLUP,
-	GPIO1_GPIO	| PIN_OUTPUT_HIGH,
-	GPIO2_GPIO	| PIN_INPUT_PULLUP,
-	GPIO3_GPIO	| PIN_OUTPUT_HIGH,
-
-	GPIO29_U2_RXD	| PIN_INPUT_PULLUP,
-	GPIO30_U2_TXD	| PIN_OUTPUT_HIGH,
-	GPIO31_U2_CTSn	| PIN_INPUT_PULLUP,
-	GPIO32_U2_RTSn	| PIN_OUTPUT_HIGH,
-
-	/* Display & HDMI HW sync */
-	GPIO68_LCD_VSI0	| PIN_INPUT_PULLUP,
-	GPIO69_LCD_VSI1	| PIN_INPUT_PULLUP,
+	DB8500_PIN_HOG("GPIO0_AJ5", in_pu), /* CTS */
+	DB8500_PIN_HOG("GPIO1_AJ3", out_hi), /* RTS */
+	DB8500_PIN_HOG("GPIO2_AH4", in_pu), /* RXD */
+	DB8500_PIN_HOG("GPIO3_AH3", out_hi), /* TXD */
+	/*
+	 * Mux in UART2 on altfunction C and set pull-ups.
+	 * TODO: is this used on U8500 variants and Snowball really?
+	 * The setting on GPIO31 conflicts with magnetometer use on hrefv60
+	 */
+	DB8500_MUX_HOG("u2rxtx_c_1", "u2"),
+	DB8500_MUX_HOG("u2ctsrts_c_1", "u2"),
+	DB8500_PIN_HOG("GPIO29_W2", in_pu), /* RXD */
+	DB8500_PIN_HOG("GPIO30_W3", out_hi), /* TXD */
+	DB8500_PIN_HOG("GPIO31_V3", in_pu), /* CTS */
+	DB8500_PIN_HOG("GPIO32_V2", out_hi), /* RTS */
+	/*
+	 * The following pin sets were known as "runtime pins" before being
+	 * converted to the pinctrl model. Here we model them as "default"
+	 * states.
+	 */
+	/* Mux in UART0 after initialization */
+	DB8500_MUX("u0_a_1", "u0", "uart0"),
+	DB8500_PIN("GPIO0_AJ5", in_pu, "uart0"), /* CTS */
+	DB8500_PIN("GPIO1_AJ3", out_hi, "uart0"), /* RTS */
+	DB8500_PIN("GPIO2_AH4", in_pu, "uart0"), /* RXD */
+	DB8500_PIN("GPIO3_AH3", out_hi, "uart0"), /* TXD */
+	/* UART0 sleep state */
+	DB8500_PIN_SLEEP("GPIO0_AJ5", sleep_in_wkup_pdis, "uart0"),
+	DB8500_PIN_SLEEP("GPIO1_AJ3", sleep_out_hi_wkup_pdis, "uart0"),
+	DB8500_PIN_SLEEP("GPIO2_AH4", sleep_in_wkup_pdis, "uart0"),
+	DB8500_PIN_SLEEP("GPIO3_AH3", sleep_out_wkup_pdis, "uart0"),
+	/* MSP1 for ALSA codec */
+	DB8500_MUX("msp1txrx_a_1", "msp1", "ux500-msp-i2s.1"),
+	DB8500_MUX("msp1_a_1", "msp1", "ux500-msp-i2s.1"),
+	DB8500_PIN("GPIO33_AF2", out_lo_sleep_nowkup, "ux500-msp-i2s.1"),
+	DB8500_PIN("GPIO34_AE1", in_nopull_sleep_nowkup, "ux500-msp-i2s.1"),
+	DB8500_PIN("GPIO35_AE2", in_nopull_sleep_nowkup, "ux500-msp-i2s.1"),
+	DB8500_PIN("GPIO36_AG2", in_nopull_sleep_nowkup, "ux500-msp-i2s.1"),
+	/* MSP1 sleep state */
+	DB8500_PIN_SLEEP("GPIO33_AF2", sleep_out_lo_wkup, "ux500-msp-i2s.1"),
+	DB8500_PIN_SLEEP("GPIO34_AE1", sleep_in_nopull_wkup, "ux500-msp-i2s.1"),
+	DB8500_PIN_SLEEP("GPIO35_AE2", sleep_in_nopull_wkup, "ux500-msp-i2s.1"),
+	DB8500_PIN_SLEEP("GPIO36_AG2", sleep_in_nopull_wkup, "ux500-msp-i2s.1"),
+	/* Mux in LCD data lines 8 thru 11 and LCDA CLK for MCDE TVOUT */
+	DB8500_MUX("lcd_d8_d11_a_1", "lcd", "mcde-tvout"),
+	DB8500_MUX("lcdaclk_b_1", "lcda", "mcde-tvout"),
+	/* Mux in LCD VSI1 and pull it up for MCDE HDMI output */
+	DB8500_MUX("lcdvsi1_a_1", "lcd", "av8100-hdmi"),
+	/* Mux in I2C blocks, put pins into GPIO in sleepmode no pull-up */
+	DB8500_MUX("i2c0_a_1", "i2c0", "nmk-i2c.0"),
+	DB8500_PIN("GPIO147_C15", slpm_gpio_nopull, "nmk-i2c.0"),
+	DB8500_PIN("GPIO148_B16", slpm_gpio_nopull, "nmk-i2c.0"),
+	DB8500_MUX("i2c1_b_2", "i2c1", "nmk-i2c.1"),
+	DB8500_PIN("GPIO16_AD3", slpm_gpio_nopull, "nmk-i2c.1"),
+	DB8500_PIN("GPIO17_AD4", slpm_gpio_nopull, "nmk-i2c.1"),
+	DB8500_MUX("i2c2_b_2", "i2c2", "nmk-i2c.2"),
+	DB8500_PIN("GPIO10_AF5", slpm_gpio_nopull, "nmk-i2c.2"),
+	DB8500_PIN("GPIO11_AG4", slpm_gpio_nopull, "nmk-i2c.2"),
+	DB8500_MUX("i2c3_c_2", "i2c3", "nmk-i2c.3"),
+	DB8500_PIN("GPIO229_AG7", slpm_gpio_nopull, "nmk-i2c.3"),
+	DB8500_PIN("GPIO230_AF7", slpm_gpio_nopull, "nmk-i2c.3"),
+	/* Mux in SDI0 (here called MC0) used for removable MMC/SD/SDIO cards */
+	DB8500_MUX("mc0_a_1", "mc0", "sdi0"),
+	DB8500_PIN("GPIO18_AC2", out_hi, "sdi0"), /* CMDDIR */
+	DB8500_PIN("GPIO19_AC1", out_hi, "sdi0"), /* DAT0DIR */
+	DB8500_PIN("GPIO20_AB4", out_hi, "sdi0"), /* DAT2DIR */
+	DB8500_PIN("GPIO22_AA3", in_nopull, "sdi0"), /* FBCLK */
+	DB8500_PIN("GPIO23_AA4", out_lo, "sdi0"), /* CLK */
+	DB8500_PIN("GPIO24_AB2", in_pu, "sdi0"), /* CMD */
+	DB8500_PIN("GPIO25_Y4", in_pu, "sdi0"), /* DAT0 */
+	DB8500_PIN("GPIO26_Y2", in_pu, "sdi0"), /* DAT1 */
+	DB8500_PIN("GPIO27_AA2", in_pu, "sdi0"), /* DAT2 */
+	DB8500_PIN("GPIO28_AA1", in_pu, "sdi0"), /* DAT3 */
+	/* Mux in SDI1 (here called MC1) used for SDIO for CW1200 WLAN */
+	DB8500_MUX("mc1_a_1", "mc1", "sdi1"),
+	DB8500_PIN("GPIO208_AH16", out_lo, "sdi1"), /* CLK */
+	DB8500_PIN("GPIO209_AG15", in_nopull, "sdi1"), /* FBCLK */
+	DB8500_PIN("GPIO210_AJ15", in_pu, "sdi1"), /* CMD */
+	DB8500_PIN("GPIO211_AG14", in_pu, "sdi1"), /* DAT0 */
+	DB8500_PIN("GPIO212_AF13", in_pu, "sdi1"), /* DAT1 */
+	DB8500_PIN("GPIO213_AG13", in_pu, "sdi1"), /* DAT2 */
+	DB8500_PIN("GPIO214_AH15", in_pu, "sdi1"), /* DAT3 */
+	/* Mux in SDI2 (here called MC2) used for for PoP eMMC */
+	DB8500_MUX("mc2_a_1", "mc2", "sdi2"),
+	DB8500_PIN("GPIO128_A5", out_lo, "sdi2"), /* CLK */
+	DB8500_PIN("GPIO129_B4", in_pu, "sdi2"), /* CMD */
+	DB8500_PIN("GPIO130_C8", in_nopull, "sdi2"), /* FBCLK */
+	DB8500_PIN("GPIO131_A12", in_pu, "sdi2"), /* DAT0 */
+	DB8500_PIN("GPIO132_C10", in_pu, "sdi2"), /* DAT1 */
+	DB8500_PIN("GPIO133_B10", in_pu, "sdi2"), /* DAT2 */
+	DB8500_PIN("GPIO134_B9", in_pu, "sdi2"), /* DAT3 */
+	DB8500_PIN("GPIO135_A9", in_pu, "sdi2"), /* DAT4 */
+	DB8500_PIN("GPIO136_C7", in_pu, "sdi2"), /* DAT5 */
+	DB8500_PIN("GPIO137_A7", in_pu, "sdi2"), /* DAT6 */
+	DB8500_PIN("GPIO138_C5", in_pu, "sdi2"), /* DAT7 */
+	/* Mux in SDI4 (here called MC4) used for for PCB-mounted eMMC */
+	DB8500_MUX("mc4_a_1", "mc4", "sdi4"),
+	DB8500_PIN("GPIO197_AH24", in_pu, "sdi4"), /* DAT3 */
+	DB8500_PIN("GPIO198_AG25", in_pu, "sdi4"), /* DAT2 */
+	DB8500_PIN("GPIO199_AH23", in_pu, "sdi4"), /* DAT1 */
+	DB8500_PIN("GPIO200_AH26", in_pu, "sdi4"), /* DAT0 */
+	DB8500_PIN("GPIO201_AF24", in_pu, "sdi4"), /* CMD */
+	DB8500_PIN("GPIO202_AF25", in_nopull, "sdi4"), /* FBCLK */
+	DB8500_PIN("GPIO203_AE23", out_lo, "sdi4"), /* CLK */
+	DB8500_PIN("GPIO204_AF23", in_pu, "sdi4"), /* DAT7 */
+	DB8500_PIN("GPIO205_AG23", in_pu, "sdi4"), /* DAT6 */
+	DB8500_PIN("GPIO206_AG24", in_pu, "sdi4"), /* DAT5 */
+	DB8500_PIN("GPIO207_AJ23", in_pu, "sdi4"), /* DAT4 */
+	/* Mux in USB pins, drive STP high */
+	DB8500_MUX("usb_a_1", "usb", "musb-ux500.0"),
+	DB8500_PIN("GPIO257_AE29", out_hi, "musb-ux500.0"), /* STP */
+	/* Mux in SPI2 pins on the "other C1" altfunction */
+	DB8500_MUX("spi2_oc1_1", "spi2", "spi2"),
+	DB8500_PIN("GPIO216_AG12", gpio_out_hi, "spi2"), /* FRM */
+	DB8500_PIN("GPIO218_AH11", in_pd, "spi2"), /* RXD */
+	DB8500_PIN("GPIO215_AH13", out_lo, "spi2"), /* TXD */
+	DB8500_PIN("GPIO217_AH12", out_lo, "spi2"), /* CLK */
 };
 
-static pin_cfg_t mop500_pins_default[] = {
-	/* SSP0 */
-	GPIO143_SSP0_CLK,
-	GPIO144_SSP0_FRM,
-	GPIO145_SSP0_RXD | PIN_PULL_DOWN,
-	GPIO146_SSP0_TXD,
-
-
-	GPIO217_GPIO	| PIN_INPUT_PULLUP, /* TC35892 IRQ */
-
-	/* SDI0 (MicroSD card) */
-	GPIO21_MC0_DAT31DIR	| PIN_OUTPUT_HIGH,
-
-	/* UART */
-	GPIO4_U1_RXD	| PIN_INPUT_PULLUP,
-	GPIO5_U1_TXD	| PIN_OUTPUT_HIGH,
-	GPIO6_U1_CTSn	| PIN_INPUT_PULLUP,
-	GPIO7_U1_RTSn	| PIN_OUTPUT_HIGH,
+/*
+ * These are specifically for the MOP500 and HREFP (pre-v60) version of the
+ * board, which utilized a TC35892 GPIO expander instead of using a lot of
+ * on-chip pins as the HREFv60 and later does.
+ */
+static struct pinctrl_map __initdata mop500_pinmap[] = {
+	/* Mux in SSP0, pull down RXD pin */
+	DB8500_MUX_HOG("ssp0_a_1", "ssp0"),
+	DB8500_PIN_HOG("GPIO145_C13", pd),
+	/*
+	 * XENON Flashgun on image processor GPIO (controlled from image
+	 * processor firmware), mux in these image processor GPIO lines 0
+	 * (XENON_FLASH_ID) and 1 (XENON_READY) on altfunction C and pull up
+	 * the pins.
+	 */
+	DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
+	DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
+	DB8500_PIN_HOG("GPIO6_AF6", in_pu),
+	DB8500_PIN_HOG("GPIO7_AG5", in_pu),
+	/* TC35892 IRQ, pull up the line, let the driver mux in the pin */
+	DB8500_PIN_HOG("GPIO217_AH12", gpio_in_pu),
+	/* Mux in UART1 and set the pull-ups */
+	DB8500_MUX_HOG("u1rxtx_a_1", "u1"),
+	DB8500_MUX_HOG("u1ctsrts_a_1", "u1"),
+	DB8500_PIN_HOG("GPIO4_AH6", in_pu), /* RXD */
+	DB8500_PIN_HOG("GPIO5_AG6", out_hi), /* TXD */
+	DB8500_PIN_HOG("GPIO6_AF6", in_pu), /* CTS */
+	DB8500_PIN_HOG("GPIO7_AG5", out_hi), /* RTS */
+	/*
+	 * Runtime stuff: make it possible to mux in the SKE keypad
+	 * and bias the pins
+	 */
+	DB8500_MUX("kp_a_2", "kp", "ske"),
+	DB8500_PIN("GPIO153_B17", in_pd_slpm_in_pu, "ske"), /* I7 */
+	DB8500_PIN("GPIO154_C16", in_pd_slpm_in_pu, "ske"), /* I6 */
+	DB8500_PIN("GPIO155_C19", in_pd_slpm_in_pu, "ske"), /* I5 */
+	DB8500_PIN("GPIO156_C17", in_pd_slpm_in_pu, "ske"), /* I4 */
+	DB8500_PIN("GPIO161_D21", in_pd_slpm_in_pu, "ske"), /* I3 */
+	DB8500_PIN("GPIO162_D20", in_pd_slpm_in_pu, "ske"), /* I2 */
+	DB8500_PIN("GPIO163_C20", in_pd_slpm_in_pu, "ske"), /* I1 */
+	DB8500_PIN("GPIO164_B21", in_pd_slpm_in_pu, "ske"), /* I0 */
+	DB8500_PIN("GPIO157_A18", in_pu_slpm_out_lo, "ske"), /* O7 */
+	DB8500_PIN("GPIO158_C18", in_pu_slpm_out_lo, "ske"), /* O6 */
+	DB8500_PIN("GPIO159_B19", in_pu_slpm_out_lo, "ske"), /* O5 */
+	DB8500_PIN("GPIO160_B20", in_pu_slpm_out_lo, "ske"), /* O4 */
+	DB8500_PIN("GPIO165_C21", in_pu_slpm_out_lo, "ske"), /* O3 */
+	DB8500_PIN("GPIO166_A22", in_pu_slpm_out_lo, "ske"), /* O2 */
+	DB8500_PIN("GPIO167_B24", in_pu_slpm_out_lo, "ske"), /* O1 */
+	DB8500_PIN("GPIO168_C22", in_pu_slpm_out_lo, "ske"), /* O0 */
+	/* Mux in and drive the SDI0 DAT31DIR line high at runtime */
+	DB8500_MUX("mc0dat31dir_a_1", "mc0", "sdi0"),
+	DB8500_PIN("GPIO21_AB3", out_hi, "sdi0"),
 };
 
-static pin_cfg_t hrefv60_pins[] = {
-	/* WLAN */
-	GPIO4_GPIO		| PIN_INPUT_PULLUP,/* WLAN_IRQ */
-	GPIO85_GPIO		| PIN_OUTPUT_LOW,/* WLAN_ENA */
-
-	/* XENON Flashgun INTERFACE */
-	GPIO6_IP_GPIO0	| PIN_INPUT_PULLUP,/* XENON_FLASH_ID */
-	GPIO7_IP_GPIO1	| PIN_INPUT_PULLUP,/* XENON_READY */
-	GPIO170_GPIO	| PIN_OUTPUT_LOW, /* XENON_CHARGE */
-
-	/* Assistant LED INTERFACE */
-	GPIO21_GPIO | PIN_OUTPUT_LOW,  /* XENON_EN1 */
-	GPIO64_IP_GPIO4 | PIN_OUTPUT_LOW,  /* XENON_EN2 */
-
-	/* Magnetometer */
-	GPIO31_GPIO | PIN_INPUT_PULLUP,  /* magnetometer_INT */
-	GPIO32_GPIO | PIN_INPUT_PULLDOWN, /* Magnetometer DRDY */
-
-	/* Display Interface */
-	GPIO65_GPIO		| PIN_OUTPUT_LOW, /* DISP1 RST */
-	GPIO66_GPIO		| PIN_OUTPUT_LOW, /* DISP2 RST */
-
-	/* Touch screen INTERFACE */
-	GPIO143_GPIO	| PIN_OUTPUT_LOW,/*TOUCH_RST1 */
-
-	/* Touch screen INTERFACE 2 */
-	GPIO67_GPIO	| PIN_INPUT_PULLUP, /* TOUCH_INT2 */
-	GPIO146_GPIO	| PIN_OUTPUT_LOW,/*TOUCH_RST2 */
-
-	/* ETM_PTM_TRACE INTERFACE */
-	GPIO70_GPIO	| PIN_OUTPUT_LOW,/* ETM_PTM_DATA23 */
-	GPIO71_GPIO	| PIN_OUTPUT_LOW,/* ETM_PTM_DATA22 */
-	GPIO72_GPIO	| PIN_OUTPUT_LOW,/* ETM_PTM_DATA21 */
-	GPIO73_GPIO	| PIN_OUTPUT_LOW,/* ETM_PTM_DATA20 */
-	GPIO74_GPIO	| PIN_OUTPUT_LOW,/* ETM_PTM_DATA19 */
-
-	/* NAHJ INTERFACE */
-	GPIO76_GPIO	| PIN_OUTPUT_LOW,/* NAHJ_CTRL */
-	GPIO216_GPIO	| PIN_OUTPUT_HIGH,/* NAHJ_CTRL_INV */
-
-	/* NFC INTERFACE */
-	GPIO77_GPIO	| PIN_OUTPUT_LOW, /* NFC_ENA */
-	GPIO144_GPIO	| PIN_INPUT_PULLDOWN, /* NFC_IRQ */
-	GPIO142_GPIO	| PIN_OUTPUT_LOW, /* NFC_RESET */
-
-	/* Keyboard MATRIX INTERFACE */
-	GPIO90_MC5_CMD	| PIN_OUTPUT_LOW, /* KP_O_1 */
-	GPIO87_MC5_DAT1	| PIN_OUTPUT_LOW, /* KP_O_2 */
-	GPIO86_MC5_DAT0	| PIN_OUTPUT_LOW, /* KP_O_3 */
-	GPIO96_KP_O6	| PIN_OUTPUT_LOW, /* KP_O_6 */
-	GPIO94_KP_O7	| PIN_OUTPUT_LOW, /* KP_O_7 */
-	GPIO93_MC5_DAT4	| PIN_INPUT_PULLUP, /* KP_I_0 */
-	GPIO89_MC5_DAT3	| PIN_INPUT_PULLUP, /* KP_I_2 */
-	GPIO88_MC5_DAT2	| PIN_INPUT_PULLUP, /* KP_I_3 */
-	GPIO91_GPIO	| PIN_INPUT_PULLUP, /* FORCE_SENSING_INT */
-	GPIO92_GPIO	| PIN_OUTPUT_LOW, /* FORCE_SENSING_RST */
-	GPIO97_GPIO	| PIN_OUTPUT_LOW, /* FORCE_SENSING_WU */
-
-	/* DiPro Sensor Interface */
-	GPIO139_GPIO	| PIN_INPUT_PULLUP, /* DIPRO_INT */
-
-	/* HAL SWITCH INTERFACE */
-	GPIO145_GPIO	| PIN_INPUT_PULLDOWN,/* HAL_SW */
-
-	/* Audio Amplifier Interface */
-	GPIO149_GPIO	| PIN_OUTPUT_LOW, /* VAUDIO_HF_EN */
-
-	/* GBF INTERFACE */
-	GPIO171_GPIO	| PIN_OUTPUT_LOW, /* GBF_ENA_RESET */
-
-	/* MSP : HDTV INTERFACE */
-	GPIO192_GPIO	| PIN_INPUT_PULLDOWN,
-
-	/* ACCELEROMETER_INTERFACE */
-	GPIO82_GPIO		| PIN_INPUT_PULLUP, /* ACC_INT1 */
-	GPIO83_GPIO		| PIN_INPUT_PULLUP, /* ACC_INT2 */
-
-	/* Proximity Sensor */
-	GPIO217_GPIO		| PIN_INPUT_PULLUP,
-
-
+/*
+ * The HREFv60 series of platforms is using available pins on the DB8500
+ * insteaf of the Toshiba I2C GPIO expander, reusing some pins like the SSP0
+ * and SSP1 ports (previously connected to the AB8500) as generic GPIO lines.
+ */
+static struct pinctrl_map __initdata hrefv60_pinmap[] = {
+	/* Drive WLAN_ENA low */
+	DB8500_PIN_HOG("GPIO85_D5", gpio_out_lo), /* WLAN_ENA */
+	/*
+	 * XENON Flashgun on image processor GPIO (controlled from image
+	 * processor firmware), mux in these image processor GPIO lines 0
+	 * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
+	 * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
+	 * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
+	 */
+	DB8500_MUX_HOG("ipgpio0_c_1", "ipgpio"),
+	DB8500_MUX_HOG("ipgpio1_c_1", "ipgpio"),
+	DB8500_MUX_HOG("ipgpio4_c_1", "ipgpio"),
+	DB8500_PIN_HOG("GPIO6_AF6", in_pu), /* XENON_FLASH_ID */
+	DB8500_PIN_HOG("GPIO7_AG5", in_pu), /* XENON_READY */
+	DB8500_PIN_HOG("GPIO21_AB3", gpio_out_lo), /* XENON_EN1 */
+	DB8500_PIN_HOG("GPIO64_F3", out_lo), /* XENON_EN2 */
+	/* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */
+	DB8500_PIN_HOG("GPIO31_V3", gpio_in_pu), /* EN1 */
+	DB8500_PIN_HOG("GPIO32_V2", gpio_in_pd), /* DRDY */
+	/*
+	 * Display Interface 1 uses GPIO 65 for RST (reset).
+	 * Display Interface 2 uses GPIO 66 for RST (reset).
+	 * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
+	 */
+	DB8500_PIN_HOG("GPIO65_F1", gpio_out_hi), /* DISP1 NO RST */
+	DB8500_PIN_HOG("GPIO66_G3", gpio_out_lo), /* DISP2 RST */
+	/*
+	 * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and
+	 * GPIO 67 for interrupts. Pull-up the IRQ line and drive both
+	 * reset signals low.
+	 */
+	DB8500_PIN_HOG("GPIO143_D12", gpio_out_lo), /* TOUCH_RST1 */
+	DB8500_PIN_HOG("GPIO67_G2", gpio_in_pu), /* TOUCH_INT2 */
+	DB8500_PIN_HOG("GPIO146_D13", gpio_out_lo), /* TOUCH_RST2 */
+	/*
+	 * Drive D19-D23 for the ETM PTM trace interface low,
+	 * (presumably pins are unconnected therefore grounded here,
+	 * the "other alt C1" setting enables these pins)
+	 */
+	DB8500_PIN_HOG("GPIO70_G5", gpio_out_lo),
+	DB8500_PIN_HOG("GPIO71_G4", gpio_out_lo),
+	DB8500_PIN_HOG("GPIO72_H4", gpio_out_lo),
+	DB8500_PIN_HOG("GPIO73_H3", gpio_out_lo),
+	DB8500_PIN_HOG("GPIO74_J3", gpio_out_lo),
+	/* NAHJ CTRL on GPIO 76 to low, CTRL_INV on GPIO216 to high */
+	DB8500_PIN_HOG("GPIO76_J2", gpio_out_lo), /* CTRL */
+	DB8500_PIN_HOG("GPIO216_AG12", gpio_out_hi), /* CTRL_INV */
+	/* NFC ENA and RESET to low, pulldown IRQ line */
+	DB8500_PIN_HOG("GPIO77_H1", gpio_out_lo), /* NFC_ENA */
+	DB8500_PIN_HOG("GPIO144_B13", gpio_in_pd), /* NFC_IRQ */
+	DB8500_PIN_HOG("GPIO142_C11", gpio_out_lo), /* NFC_RESET */
+	/*
+	 * SKE keyboard partly on alt A and partly on "Other alt C1"
+	 * Driver KP_O1,2,3,6,7 low and pull up KP_I