[ARM] pxa: move ssp into common plat-pxa

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

5 files changed, 1 insertions, 426 deletions

diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index 8f7eb12776a..6dd450a7dea 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -648,11 +648,6 @@ config PXA_SHARP_Cxx00
 	help
 	  Enable common support for Sharp Cxx00 models
 
-config PXA_SSP
-	tristate
-	help
-	  Enable support for PXA2xx SSP ports
-
 config TOSA_BT
 	tristate "Control the state of built-in bluetooth chip on Sharp SL-6000"
 	depends on MACH_TOSA
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index a83aff386fb..cf57fb2f73d 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -14,7 +14,6 @@ obj-$(CONFIG_PXA3xx)		+= cpufreq-pxa3xx.o
 endif
 
 # Generic drivers that other drivers may depend upon
-obj-$(CONFIG_PXA_SSP)		+= ssp.o
 
 # SoC-specific code
 obj-$(CONFIG_PXA25x)		+= mfp-pxa2xx.o pxa2xx.o pxa25x.o
diff --git a/arch/arm/mach-pxa/include/mach/ssp.h b/arch/arm/mach-pxa/include/mach/ssp.h
deleted file mode 100644
index 4c4ce62390d..00000000000
--- a/arch/arm/mach-pxa/include/mach/ssp.h
+++ /dev/null
@@ -1,196 +0,0 @@
-/*
- *  ssp.h
- *
- *  Copyright (C) 2003 Russell King, All Rights Reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This driver supports the following PXA CPU/SSP ports:-
- *
- *       PXA250     SSP
- *       PXA255     SSP, NSSP
- *       PXA26x     SSP, NSSP, ASSP
- *       PXA27x     SSP1, SSP2, SSP3
- *       PXA3xx     SSP1, SSP2, SSP3, SSP4
- */
-
-#ifndef __ASM_ARCH_SSP_H
-#define __ASM_ARCH_SSP_H
-
-#include <linux/list.h>
-#include <linux/io.h>
-
-/*
- * SSP Serial Port Registers
- * PXA250, PXA255, PXA26x and PXA27x SSP controllers are all slightly different.
- * PXA255, PXA26x and PXA27x have extra ports, registers and bits.
- */
-
-#define SSCR0		(0x00)  /* SSP Control Register 0 */
-#define SSCR1		(0x04)  /* SSP Control Register 1 */
-#define SSSR		(0x08)  /* SSP Status Register */
-#define SSITR		(0x0C)  /* SSP Interrupt Test Register */
-#define SSDR		(0x10)  /* SSP Data Write/Data Read Register */
-
-#define SSTO		(0x28)  /* SSP Time Out Register */
-#define SSPSP		(0x2C)  /* SSP Programmable Serial Protocol */
-#define SSTSA		(0x30)  /* SSP Tx Timeslot Active */
-#define SSRSA		(0x34)  /* SSP Rx Timeslot Active */
-#define SSTSS		(0x38)  /* SSP Timeslot Status */
-#define SSACD		(0x3C)  /* SSP Audio Clock Divider */
-
-#if defined(CONFIG_PXA3xx)
-#define SSACDD		(0x40)	/* SSP Audio Clock Dither Divider */
-#endif
-
-/* Common PXA2xx bits first */
-#define SSCR0_DSS	(0x0000000f)	/* Data Size Select (mask) */
-#define SSCR0_DataSize(x)  ((x) - 1)	/* Data Size Select [4..16] */
-#define SSCR0_FRF	(0x00000030)	/* FRame Format (mask) */
-#define SSCR0_Motorola	(0x0 << 4)	/* Motorola's Serial Peripheral Interface (SPI) */
-#define SSCR0_TI	(0x1 << 4)	/* Texas Instruments' Synchronous Serial Protocol (SSP) */
-#define SSCR0_National	(0x2 << 4)	/* National Microwire */
-#define SSCR0_ECS	(1 << 6)	/* External clock select */
-#define SSCR0_SSE	(1 << 7)	/* Synchronous Serial Port Enable */
-#define SSCR0_SCR(x)	((x) << 8)	/* Serial Clock Rate (mask) */
-
-#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
-#define SSCR0_EDSS	(1 << 20)	/* Extended data size select */
-#define SSCR0_NCS	(1 << 21)	/* Network clock select */
-#define SSCR0_RIM	(1 << 22)	/* Receive FIFO overrrun interrupt mask */
-#define SSCR0_TUM	(1 << 23)	/* Transmit FIFO underrun interrupt mask */
-#define SSCR0_FRDC	(0x07000000)	/* Frame rate divider control (mask) */
-#define SSCR0_SlotsPerFrm(x) (((x) - 1) << 24)	/* Time slots per frame [1..8] */
-#define SSCR0_ACS	(1 << 30)	/* Audio clock select */
-#define SSCR0_MOD	(1 << 31)	/* Mode (normal or network) */
-#endif
-
-#if defined(CONFIG_PXA3xx)
-#define SSCR0_FPCKE	(1 << 29)	/* FIFO packing enable */
-#endif
-
-#define SSCR1_RIE	(1 << 0)	/* Receive FIFO Interrupt Enable */
-#define SSCR1_TIE	(1 << 1)	/* Transmit FIFO Interrupt Enable */
-#define SSCR1_LBM	(1 << 2)	/* Loop-Back Mode */
-#define SSCR1_SPO	(1 << 3)	/* Motorola SPI SSPSCLK polarity setting */
-#define SSCR1_SPH	(1 << 4)	/* Motorola SPI SSPSCLK phase setting */
-#define SSCR1_MWDS	(1 << 5)	/* Microwire Transmit Data Size */
-#define SSCR1_TFT	(0x000003c0)	/* Transmit FIFO Threshold (mask) */
-#define SSCR1_TxTresh(x) (((x) - 1) << 6) /* level [1..16] */
-#define SSCR1_RFT	(0x00003c00)	/* Receive FIFO Threshold (mask) */
-#define SSCR1_RxTresh(x) (((x) - 1) << 10) /* level [1..16] */
-
-#define SSSR_TNF	(1 << 2)	/* Transmit FIFO Not Full */
-#define SSSR_RNE	(1 << 3)	/* Receive FIFO Not Empty */
-#define SSSR_BSY	(1 << 4)	/* SSP Busy */
-#define SSSR_TFS	(1 << 5)	/* Transmit FIFO Service Request */
-#define SSSR_RFS	(1 << 6)	/* Receive FIFO Service Request */
-#define SSSR_ROR	(1 << 7)	/* Receive FIFO Overrun */
-
-#define SSCR0_TIM		(1 << 23)	/* Transmit FIFO Under Run Interrupt Mask */
-#define SSCR0_RIM		(1 << 22)	/* Receive FIFO Over Run interrupt Mask */
-#define SSCR0_NCS		(1 << 21)	/* Network Clock Select */
-#define SSCR0_EDSS		(1 << 20)	/* Extended Data Size Select */
-
-/* extra bits in PXA255, PXA26x and PXA27x SSP ports */
-#define SSCR0_TISSP		(1 << 4)	/* TI Sync Serial Protocol */
-#define SSCR0_PSP		(3 << 4)	/* PSP - Programmable Serial Protocol */
-#define SSCR1_TTELP		(1 << 31)	/* TXD Tristate Enable Last Phase */
-#define SSCR1_TTE		(1 << 30)	/* TXD Tristate Enable */
-#define SSCR1_EBCEI		(1 << 29)	/* Enable Bit Count Error interrupt */
-#define SSCR1_SCFR		(1 << 28)	/* Slave Clock free Running */
-#define SSCR1_ECRA		(1 << 27)	/* Enable Clock Request A */
-#define SSCR1_ECRB		(1 << 26)	/* Enable Clock request B */
-#define SSCR1_SCLKDIR		(1 << 25)	/* Serial Bit Rate Clock Direction */
-#define SSCR1_SFRMDIR		(1 << 24)	/* Frame Direction */
-#define SSCR1_RWOT		(1 << 23)	/* Receive Without Transmit */
-#define SSCR1_TRAIL		(1 << 22)	/* Trailing Byte */
-#define SSCR1_TSRE		(1 << 21)	/* Transmit Service Request Enable */
-#define SSCR1_RSRE		(1 << 20)	/* Receive Service Request Enable */
-#define SSCR1_TINTE		(1 << 19)	/* Receiver Time-out Interrupt enable */
-#define SSCR1_PINTE		(1 << 18)	/* Peripheral Trailing Byte Interupt Enable */
-#define SSCR1_IFS		(1 << 16)	/* Invert Frame Signal */
-#define SSCR1_STRF		(1 << 15)	/* Select FIFO or EFWR */
-#define SSCR1_EFWR		(1 << 14)	/* Enable FIFO Write/Read */
-
-#define SSSR_BCE		(1 << 23)	/* Bit Count Error */
-#define SSSR_CSS		(1 << 22)	/* Clock Synchronisation Status */
-#define SSSR_TUR		(1 << 21)	/* Transmit FIFO Under Run */
-#define SSSR_EOC		(1 << 20)	/* End Of Chain */
-#define SSSR_TINT		(1 << 19)	/* Receiver Time-out Interrupt */
-#define SSSR_PINT		(1 << 18)	/* Peripheral Trailing Byte Interrupt */
-
-#if defined(CONFIG_PXA3xx)
-#define SSPSP_EDMYSTOP(x)	((x) << 28)     /* Extended Dummy Stop */
-#define SSPSP_EDMYSTRT(x)	((x) << 26)     /* Extended Dummy Start */
-#endif
-
-#define SSPSP_FSRT		(1 << 25)	/* Frame Sync Relative Timing */
-#define SSPSP_DMYSTOP(x)	((x) << 23)	/* Dummy Stop */
-#define SSPSP_SFRMWDTH(x)	((x) << 16)	/* Serial Frame Width */
-#define SSPSP_SFRMDLY(x)	((x) << 9)	/* Serial Frame Delay */
-#define SSPSP_DMYSTRT(x)	((x) << 7)	/* Dummy Start */
-#define SSPSP_STRTDLY(x)	((x) << 4)	/* Start Delay */
-#define SSPSP_ETDS		(1 << 3)	/* End of Transfer data State */
-#define SSPSP_SFRMP		(1 << 2)	/* Serial Frame Polarity */
-#define SSPSP_SCMODE(x)		((x) << 0)	/* Serial Bit Rate Clock Mode */
-
-#define SSACD_SCDB		(1 << 3)	/* SSPSYSCLK Divider Bypass */
-#define SSACD_ACPS(x)		((x) << 4)	/* Audio clock PLL select */
-#define SSACD_ACDS(x)		((x) << 0)	/* Audio clock divider select */
-#if defined(CONFIG_PXA3xx)
-#define SSACD_SCDX8		(1 << 7)	/* SYSCLK division ratio select */
-#endif
-
-enum pxa_ssp_type {
-	SSP_UNDEFINED = 0,
-	PXA25x_SSP,  /* pxa 210, 250, 255, 26x */
-	PXA25x_NSSP, /* pxa 255, 26x (including ASSP) */
-	PXA27x_SSP,
-};
-
-struct ssp_device {
-	struct platform_device *pdev;
-	struct list_head	node;
-
-	struct clk	*clk;
-	void __iomem	*mmio_base;
-	unsigned long	phys_base;
-
-	const char	*label;
-	int		port_id;
-	int		type;
-	int		use_count;
-	int		irq;
-	int		drcmr_rx;
-	int		drcmr_tx;
-};
-
-/**
- * ssp_write_reg - Write to a SSP register
- *
- * @dev: SSP device to access
- * @reg: Register to write to
- * @val: Value to be written.
- */
-static inline void ssp_write_reg(struct ssp_device *dev, u32 reg, u32 val)
-{
-	__raw_writel(val, dev->mmio_base + reg);
-}
-
-/**
- * ssp_read_reg - Read from a SSP register
- *
- * @dev: SSP device to access
- * @reg: Register to read from
- */
-static inline u32 ssp_read_reg(struct ssp_device *dev, u32 reg)
-{
-	return __raw_readl(dev->mmio_base + reg);
-}
-
-struct ssp_device *ssp_request(int port, const char *label);
-void ssp_free(struct ssp_device *);
-#endif /* __ASM_ARCH_SSP_H */
diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c
index 48b10c783a2..dcb17880704 100644
--- a/arch/arm/mach-pxa/poodle.c
+++ b/arch/arm/mach-pxa/poodle.c
@@ -40,12 +40,12 @@
 #include <mach/pxa25x.h>
 #include <mach/mmc.h>
 #include <mach/udc.h>
-#include <plat/i2c.h>
 #include <mach/irda.h>
 #include <mach/poodle.h>
 #include <mach/pxafb.h>
 #include <mach/sharpsl.h>
 #include <mach/pxa2xx_spi.h>
+#include <plat/i2c.h>
 
 #include <asm/hardware/scoop.h>
 #include <asm/hardware/locomo.h>
diff --git a/arch/arm/mach-pxa/ssp.c b/arch/arm/mach-pxa/ssp.c
deleted file mode 100644
index a9b2d3eb8f3..00000000000
--- a/arch/arm/mach-pxa/ssp.c
+++ /dev/null
@@ -1,223 +0,0 @@
-/*
- *  linux/arch/arm/mach-pxa/ssp.c
- *
- *  based on linux/arch/arm/mach-sa1100/ssp.c by Russell King
- *
- *  Copyright (C) 2003 Russell King.
- *  Copyright (C) 2003 Wolfson Microelectronics PLC
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  PXA2xx SSP driver.  This provides the generic core for simple
- *  IO-based SSP applications and allows easy port setup for DMA access.
- *
- *  Author: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/sched.h>
-#include <linux/slab.h>
-#include <linux/errno.h>
-#include <linux/interrupt.h>
-#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/mutex.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-#include <mach/ssp.h>
-
-static DEFINE_MUTEX(ssp_lock);
-static LIST_HEAD(ssp_list);
-
-struct ssp_device *ssp_request(int port, const char *label)
-{
-	struct ssp_device *ssp = NULL;
-
-	mutex_lock(&ssp_lock);
-
-	list_for_each_entry(ssp, &ssp_list, node) {
-		if (ssp->port_id == port && ssp->use_count == 0) {
-			ssp->use_count++;
-			ssp->label = label;
-			break;
-		}
-	}
-
-	mutex_unlock(&ssp_lock);
-
-	if (&ssp->node == &ssp_list)
-		return NULL;
-
-	return ssp;
-}
-EXPORT_SYMBOL(ssp_request);
-
-void ssp_free(struct ssp_device *ssp)
-{
-	mutex_lock(&ssp_lock);
-	if (ssp->use_count) {
-		ssp->use_count--;
-		ssp->label = NULL;
-	} else
-		dev_err(&ssp->pdev->dev, "device already free\n");
-	mutex_unlock(&ssp_lock);
-}
-EXPORT_SYMBOL(ssp_free);
-
-static int __devinit ssp_probe(struct platform_device *pdev)
-{
-	const struct platform_device_id *id = platform_get_device_id(pdev);
-	struct resource *res;
-	struct ssp_device *ssp;
-	int ret = 0;
-
-	ssp = kzalloc(sizeof(struct ssp_device), GFP_KERNEL);
-	if (ssp == NULL) {
-		dev_err(&pdev->dev, "failed to allocate memory");
-		return -ENOMEM;
-	}
-	ssp->pdev = pdev;
-
-	ssp->clk = clk_get(&pdev->dev, NULL);
-	if (IS_ERR(ssp->clk)) {
-		ret = PTR_ERR(ssp->clk);
-		goto err_free;
-	}
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (res == NULL) {
-		dev_err(&pdev->dev, "no memory resource defined\n");
-		ret = -ENODEV;
-		goto err_free_clk;
-	}
-
-	res = request_mem_region(res->start, res->end - res->start + 1,
-			pdev->name);
-	if (res == NULL) {
-		dev_err(&pdev->dev, "failed to request memory resource\n");
-		ret = -EBUSY;
-		goto err_free_clk;
-	}
-
-	ssp->phys_base = res->start;
-
-	ssp->mmio_base = ioremap(res->start, res->end - res->start + 1);
-	if (ssp->mmio_base == NULL) {
-		dev_err(&pdev->dev, "failed to ioremap() registers\n");
-		ret = -ENODEV;
-		goto err_free_mem;
-	}
-
-	ssp->irq = platform_get_irq(pdev, 0);
-	if (ssp->irq < 0) {
-		dev_err(&pdev->dev, "no IRQ resource defined\n");
-		ret = -ENODEV;
-		goto err_free_io;
-	}
-
-	res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
-	if (res == NULL) {
-		dev_err(&pdev->dev, "no SSP RX DRCMR defined\n");
-		ret = -ENODEV;
-		goto err_free_io;
-	}
-	ssp->drcmr_rx = res->start;
-
-	res = platform_get_resource(pdev, IORESOURCE_DMA, 1);
-	if (res == NULL) {
-		dev_err(&pdev->dev, "no SSP TX DRCMR defined\n");
-		ret = -ENODEV;
-		goto err_free_io;
-	}
-	ssp->drcmr_tx = res->start;
-
-	/* PXA2xx/3xx SSP ports starts from 1 and the internal pdev->id
-	 * starts from 0, do a translation here
-	 */
-	ssp->port_id = pdev->id + 1;
-	ssp->use_count = 0;
-	ssp->type = (int)id->driver_data;
-
-	mutex_lock(&ssp_lock);
-	list_add(&ssp->node, &ssp_list);
-	mutex_unlock(&ssp_lock);
-
-	platform_set_drvdata(pdev, ssp);
-	return 0;
-
-err_free_io:
-	iounmap(ssp->mmio_base);
-err_free_mem:
-	release_mem_region(res->start, res->end - res->start + 1);
-err_free_clk:
-	clk_put(ssp->clk);
-err_free:
-	kfree(ssp);
-	return ret;
-}
-
-static int __devexit ssp_remove(struct platform_device *pdev)
-{
-	struct resource *res;
-	struct ssp_device *ssp;
-
-	ssp = platform_get_drvdata(pdev);
-	if (ssp == NULL)
-		return -ENODEV;
-
-	iounmap(ssp->mmio_base);
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	release_mem_region(res->start, res->end - res->start + 1);
-
-	clk_put(ssp->clk);
-
-	mutex_lock(&ssp_lock);
-	list_del(&ssp->node);
-	mutex_unlock(&ssp_lock);
-
-	kfree(ssp);
-	return 0;
-}
-
-static const struct platform_device_id ssp_id_table[] = {
-	{ "pxa25x-ssp",		PXA25x_SSP },
-	{ "pxa25x-nssp",	PXA25x_NSSP },
-	{ "pxa27x-ssp",		PXA27x_SSP },
-	{ },
-};
-
-static struct platform_driver ssp_driver = {
-	.probe		= ssp_probe,
-	.remove		= __devexit_p(ssp_remove),
-	.driver		= {
-		.owner	= THIS_MODULE,
-		.name	= "pxa2xx-ssp",
-	},
-	.id_table	= ssp_id_table,
-};
-
-static int __init pxa_ssp_init(void)
-{
-	return platform_driver_register(&ssp_driver);
-}
-
-static void __exit pxa_ssp_exit(void)
-{
-	platform_driver_unregister(&ssp_driver);
-}
-
-arch_initcall(pxa_ssp_init);
-module_exit(pxa_ssp_exit);
-
-MODULE_DESCRIPTION("PXA SSP driver");
-MODULE_AUTHOR("Liam Girdwood");
-MODULE_LICENSE("GPL");