Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc board specific updates from Arnd Bergmann:
 "These changes are all for individual board files.  In the long run,
  those files will largely go away, and the amount of changes appears to
  be continuously decreasing, which is a good sign.  This time around,
  changes are focused on tegra, omap and samsung."

Fix conflicts in arch/arm/mach-{omap2/common-board-devices.c,tegra/Makefile.boot}
as per the 'for-linus' branch.

* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
  ARM: EXYNOS: Add leds status1 and status2 on Origen board
  ARM: S3C64XX: Mark most Cragganmore initdata devinitdata
  ARM: EXYNOS: Add missing .reserve field to SMDKC210
  ARM: EXYNOS: Add DRM device to SMDK4X12 board
  ARM: S3C64XX: Clean up after SPI driver platform data updates
  ARM: SAMSUNG: no need to set the value for clk_xusbxti when it is 24Mhz
  ARM: EXYNOS: Add framebuffer support for SMDK4X12
  ARM: EXYNOS: Add HSOTG support to SMDK4X12
  ARM: S5PV210: Add audio platform device in Goni board
  ARM: S5PV210: Add audio platform device in Aquila board
  ARM: EXYNOS: Add audio platform device in SMDKV310 board
  ARM: S3C64XX: Don't specify an irq_base for WM1192-EV1 board
  ARM: OMAP3: Fix omap3evm randconfig error introduced by VBUS support
  ARM: OMAP: board-omap4panda: MUX configuration for sys_nirq2
  ARM: OMAP: board-4430sdp: MUX configuration for sys_nirq2
  ARM: OMAP3530evm: set pendown_state and debounce time for ads7846
  ARM: omap3evm: enable VBUS switch for EHCI tranceiver
  ARM: OMAP3EVM: Adding USB internal LDOs board file
  ARM: OMAP3EVM: Add NAND flash definition
  ARM: OMAP3: cm-t35: add tvp5150 decoder support
  ...

8 files changed, 249 insertions, 1 deletions

diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index b779ddd86fa..19b771d0c0d 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -217,6 +217,10 @@ endif
 # OMAP2420 MSDI controller integration support ("MMC")
 obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
 
+ifneq ($(CONFIG_DRM_OMAP),)
+obj-y					+= drm.o
+endif
+
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o
 obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o
diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c
index 8e17284a803..ad8a7d94afc 100644
--- a/arch/arm/mach-omap2/board-4430sdp.c
+++ b/arch/arm/mach-omap2/board-4430sdp.c
@@ -821,6 +821,9 @@ static void __init omap_4430sdp_display_init(void)
 #ifdef CONFIG_OMAP_MUX
 static struct omap_board_mux board_mux[] __initdata = {
 	OMAP4_MUX(USBB2_ULPITLL_CLK, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
+	/* NIRQ2 for twl6040 */
+	OMAP4_MUX(SYS_NIRQ2, OMAP_MUX_MODE0 |
+		  OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 
diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c
index ded100c80a9..97d719047af 100644
--- a/arch/arm/mach-omap2/board-cm-t35.c
+++ b/arch/arm/mach-omap2/board-cm-t35.c
@@ -490,6 +490,71 @@ static struct twl4030_platform_data cm_t35_twldata = {
 	.power		= &cm_t35_power_data,
 };
 
+#if defined(CONFIG_VIDEO_OMAP3) || defined(CONFIG_VIDEO_OMAP3_MODULE)
+#include <media/omap3isp.h>
+#include "devices.h"
+
+static struct i2c_board_info cm_t35_isp_i2c_boardinfo[] = {
+	{
+		I2C_BOARD_INFO("mt9t001", 0x5d),
+	},
+	{
+		I2C_BOARD_INFO("tvp5150", 0x5c),
+	},
+};
+
+static struct isp_subdev_i2c_board_info cm_t35_isp_primary_subdevs[] = {
+	{
+		.board_info = &cm_t35_isp_i2c_boardinfo[0],
+		.i2c_adapter_id = 3,
+	},
+	{ NULL, 0, },
+};
+
+static struct isp_subdev_i2c_board_info cm_t35_isp_secondary_subdevs[] = {
+	{
+		.board_info = &cm_t35_isp_i2c_boardinfo[1],
+		.i2c_adapter_id = 3,
+	},
+	{ NULL, 0, },
+};
+
+static struct isp_v4l2_subdevs_group cm_t35_isp_subdevs[] = {
+	{
+		.subdevs = cm_t35_isp_primary_subdevs,
+		.interface = ISP_INTERFACE_PARALLEL,
+		.bus = {
+			.parallel = {
+				.clk_pol = 1,
+			},
+		},
+	},
+	{
+		.subdevs = cm_t35_isp_secondary_subdevs,
+		.interface = ISP_INTERFACE_PARALLEL,
+		.bus = {
+			.parallel = {
+				.clk_pol = 0,
+			},
+		},
+	},
+	{ NULL, 0, },
+};
+
+static struct isp_platform_data cm_t35_isp_pdata = {
+	.subdevs = cm_t35_isp_subdevs,
+};
+
+static void __init cm_t35_init_camera(void)
+{
+	if (omap3_init_camera(&cm_t35_isp_pdata) < 0)
+		pr_warn("CM-T3x: Failed registering camera device!\n");
+}
+
+#else
+static inline void cm_t35_init_camera(void) {}
+#endif /* CONFIG_VIDEO_OMAP3 */
+
 static void __init cm_t35_init_i2c(void)
 {
 	omap3_pmic_get_config(&cm_t35_twldata, TWL_COMMON_PDATA_USB,
@@ -497,6 +562,8 @@ static void __init cm_t35_init_i2c(void)
 			      TWL_COMMON_PDATA_AUDIO);
 
 	omap3_pmic_init("tps65930", &cm_t35_twldata);
+
+	omap_register_i2c_bus(3, 400, NULL, 0);
 }
 
 #ifdef CONFIG_OMAP_MUX
@@ -574,6 +641,27 @@ static struct omap_board_mux board_mux[] __initdata = {
 	OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
 
+	/* Camera */
+	OMAP3_MUX(CAM_HS, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_VS, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_FLD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_D0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_D1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_D2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_D3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_D4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_D5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_D6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_D7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+	OMAP3_MUX(CAM_D8, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
+	OMAP3_MUX(CAM_D9, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
+	OMAP3_MUX(CAM_STROBE, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
+
+	OMAP3_MUX(CAM_D10, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLDOWN),
+	OMAP3_MUX(CAM_D11, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLDOWN),
+
 	/* display controls */
 	OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
 	OMAP3_MUX(GPMC_NCS7, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
@@ -646,6 +734,7 @@ static void __init cm_t3x_common_init(void)
 
 	usb_musb_init(NULL);
 	cm_t35_init_usbh();
+	cm_t35_init_camera();
 }
 
 static void __init cm_t35_init(void)
diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c
index 639bd07ea38..ef230a0eb5e 100644
--- a/arch/arm/mach-omap2/board-omap3evm.c
+++ b/arch/arm/mach-omap2/board-omap3evm.c
@@ -24,6 +24,10 @@
 #include <linux/leds.h>
 #include <linux/interrupt.h>
 
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/nand.h>
+
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
 #include <linux/i2c/twl.h>
@@ -43,6 +47,7 @@
 
 #include <plat/board.h>
 #include <plat/usb.h>
+#include <plat/nand.h>
 #include "common.h"
 #include <plat/mcspi.h>
 #include <video/omapdss.h>
@@ -53,7 +58,6 @@
 #include "hsmmc.h"
 #include "common-board-devices.h"
 
-#define OMAP3_EVM_TS_GPIO	175
 #define OMAP3_EVM_EHCI_VBUS	22
 #define OMAP3_EVM_EHCI_SELECT	61
 
@@ -355,6 +359,19 @@ static int omap3evm_twl_gpio_setup(struct device *dev,
 
 	platform_device_register(&leds_gpio);
 
+	/* Enable VBUS switch by setting TWL4030.GPIO2DIR as output
+	 * for starting USB tranceiver
+	 */
+#ifdef CONFIG_TWL4030_CORE
+	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
+		u8 val;
+
+		twl_i2c_read_u8(TWL4030_MODULE_GPIO, &val, REG_GPIODATADIR1);
+		val |= 0x04; /* TWL4030.GPIO2DIR BIT at GPIODATADIR1(0x9B) */
+		twl_i2c_write_u8(TWL4030_MODULE_GPIO, val, REG_GPIODATADIR1);
+	}
+#endif
+
 	return 0;
 }
 
@@ -461,6 +478,28 @@ struct wl12xx_platform_data omap3evm_wlan_data __initdata = {
 };
 #endif
 
+/* VAUX2 for USB */
+static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = {
+	REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"),	/* OMAP ISP */
+	REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"),	/* OMAP ISP */
+	REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"),
+	REGULATOR_SUPPLY("vaux2", NULL),
+};
+
+static struct regulator_init_data omap3evm_vaux2 = {
+	.constraints = {
+		.min_uV		= 2800000,
+		.max_uV		= 2800000,
+		.apply_uV	= true,
+		.valid_modes_mask	= REGULATOR_MODE_NORMAL
+					| REGULATOR_MODE_STANDBY,
+		.valid_ops_mask		= REGULATOR_CHANGE_MODE
+					| REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies		= ARRAY_SIZE(omap3evm_vaux2_supplies),
+	.consumer_supplies		= omap3evm_vaux2_supplies,
+};
+
 static struct twl4030_platform_data omap3evm_twldata = {
 	/* platform_data for children goes here */
 	.keypad		= &omap3evm_kp_data,
@@ -607,6 +646,37 @@ static struct regulator_consumer_supply dummy_supplies[] = {
 	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
 };
 
+static struct mtd_partition omap3evm_nand_partitions[] = {
+	/* All the partition sizes are listed in terms of NAND block size */
+	{
+		.name           = "X-Loader",
+		.offset         = 0,
+		.size           = 4*(SZ_128K),
+		.mask_flags     = MTD_WRITEABLE
+	},
+	{
+		.name           = "U-Boot",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 14*(SZ_128K),
+		.mask_flags     = MTD_WRITEABLE
+	},
+	{
+		.name           = "U-Boot Env",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 2*(SZ_128K)
+	},
+	{
+		.name           = "Kernel",
+		.offset         = MTDPART_OFS_APPEND,
+		.size           = 40*(SZ_128K)
+	},
+	{
+		.name           = "File system",
+		.size           = MTDPART_SIZ_FULL,
+		.offset         = MTDPART_OFS_APPEND,
+	},
+};
+
 static void __init omap3_evm_init(void)
 {
 	struct omap_board_mux *obm;
@@ -623,6 +693,9 @@ static void __init omap3_evm_init(void)
 	omap_mux_init_gpio(63, OMAP_PIN_INPUT);
 	omap_hsmmc_init(mmc);
 
+	if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
+		omap3evm_twldata.vaux2 = &omap3evm_vaux2;
+
 	omap3_evm_i2c_init();
 
 	omap_display_init(&omap3_evm_dss_data);
@@ -656,6 +729,9 @@ static void __init omap3_evm_init(void)
 	}
 	usb_musb_init(&musb_board_data);
 	usbhs_init(&usbhs_bdata);
+	omap_nand_flash_init(NAND_BUSWIDTH_16, omap3evm_nand_partitions,
+			     ARRAY_SIZE(omap3evm_nand_partitions));
+
 	omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL);
 	omap3evm_init_smsc911x();
 	omap3_evm_display_init();
diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c
index 982fb2622ab..b627cdc12b8 100644
--- a/arch/arm/mach-omap2/board-omap4panda.c
+++ b/arch/arm/mach-omap2/board-omap4panda.c
@@ -379,6 +379,9 @@ static struct omap_board_mux board_mux[] __initdata = {
 	OMAP4_MUX(DPM_EMU18, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
 	/* dispc2_data0 */
 	OMAP4_MUX(DPM_EMU19, OMAP_PIN_OUTPUT | OMAP_MUX_MODE5),
+	/* NIRQ2 for twl6040 */
+	OMAP4_MUX(SYS_NIRQ2, OMAP_MUX_MODE0 |
+		  OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE),
 	{ .reg_offset = OMAP_MUX_TERMINATOR },
 };
 
diff --git a/arch/arm/mach-omap2/common-board-devices.c b/arch/arm/mach-omap2/common-board-devices.c
index c1875862679..14734746457 100644
--- a/arch/arm/mach-omap2/common-board-devices.c
+++ b/arch/arm/mach-omap2/common-board-devices.c
@@ -35,6 +35,16 @@ static struct omap2_mcspi_device_config ads7846_mcspi_config = {
 	.turbo_mode	= 0,
 };
 
+/*
+ * ADS7846 driver maybe request a gpio according to the value
+ * of pdata->get_pendown_state, but we have done this. So set
+ * get_pendown_state to avoid twice gpio requesting.
+ */
+static int omap3_get_pendown_state(void)
+{
+	return !gpio_get_value(OMAP3_EVM_TS_GPIO);
+}
+
 static struct ads7846_platform_data ads7846_config = {
 	.x_max			= 0x0fff,
 	.y_max			= 0x0fff,
@@ -45,6 +55,7 @@ static struct ads7846_platform_data ads7846_config = {
 	.debounce_rep		= 1,
 	.gpio_pendown		= -EINVAL,
 	.keep_vref_on		= 1,
+	.get_pendown_state	= &omap3_get_pendown_state,
 };
 
 static struct spi_board_info ads7846_spi_board_info __initdata = {
diff --git a/arch/arm/mach-omap2/common-board-devices.h b/arch/arm/mach-omap2/common-board-devices.h
index a0b4a42836a..4c4ef6a6166 100644
--- a/arch/arm/mach-omap2/common-board-devices.h
+++ b/arch/arm/mach-omap2/common-board-devices.h
@@ -4,6 +4,7 @@
 #include "twl-common.h"
 
 #define NAND_BLOCK_SIZE	SZ_128K
+#define OMAP3_EVM_TS_GPIO	175
 
 struct mtd_partition;
 struct ads7846_platform_data;
diff --git a/arch/arm/mach-omap2/drm.c b/arch/arm/mach-omap2/drm.c
new file mode 100644
index 00000000000..72e0f01b715
--- /dev/null
+++ b/arch/arm/mach-omap2/drm.c
@@ -0,0 +1,61 @@
+/*
+ * DRM/KMS device registration for TI OMAP platforms
+ *
+ * Copyright (C) 2012 Texas Instruments
+ * Author: Rob Clark <rob.clark@linaro.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
+
+#include <plat/omap_device.h>
+#include <plat/omap_hwmod.h>
+
+#if defined(CONFIG_DRM_OMAP) || (CONFIG_DRM_OMAP_MODULE)
+
+static struct platform_device omap_drm_device = {
+	.dev = {
+		.coherent_dma_mask = DMA_BIT_MASK(32),
+	},
+	.name = "omapdrm",
+	.id = 0,
+};
+
+static int __init omap_init_drm(void)
+{
+	struct omap_hwmod *oh = NULL;
+	struct platform_device *pdev;
+
+	/* lookup and populate the DMM information, if present - OMAP4+ */
+	oh = omap_hwmod_lookup("dmm");
+
+	if (oh) {
+		pdev = omap_device_build(oh->name, -1, oh, NULL, 0, NULL, 0,
+					false);
+		WARN(IS_ERR(pdev), "Could not build omap_device for %s\n",
+			oh->name);
+	}
+
+	return platform_device_register(&omap_drm_device);
+
+}
+
+arch_initcall(omap_init_drm);
+
+#endif