Merge branch 'devel-stable' into devel

8 files changed, 92 insertions, 346 deletions

diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index ca33862b4bf..851e8139ef9 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -33,6 +33,7 @@ config ARCH_AT91SAM9260
 	select HAVE_AT91_USART3
 	select HAVE_AT91_USART4
 	select HAVE_AT91_USART5
+	select HAVE_NET_MACB
 
 config ARCH_AT91SAM9261
 	bool "AT91SAM9261"
@@ -51,6 +52,7 @@ config ARCH_AT91SAM9263
 	select CPU_ARM926T
 	select GENERIC_CLOCKEVENTS
 	select HAVE_FB_ATMEL
+	select HAVE_NET_MACB
 
 config ARCH_AT91SAM9RL
 	bool "AT91SAM9RL"
@@ -66,6 +68,7 @@ config ARCH_AT91SAM9G20
 	select HAVE_AT91_USART3
 	select HAVE_AT91_USART4
 	select HAVE_AT91_USART5
+	select HAVE_NET_MACB
 
 config ARCH_AT91SAM9G45
 	bool "AT91SAM9G45"
@@ -73,6 +76,7 @@ config ARCH_AT91SAM9G45
 	select GENERIC_CLOCKEVENTS
 	select HAVE_AT91_USART3
 	select HAVE_FB_ATMEL
+	select HAVE_NET_MACB
 
 config ARCH_AT91CAP9
 	bool "AT91CAP9"
@@ -344,6 +348,7 @@ config MACH_AT91SAM9G20EK
 	  that embeds only one SD/MMC slot.
 
 config MACH_AT91SAM9G20EK_2MMC
+	depends on MACH_AT91SAM9G20EK
 	bool "Atmel AT91SAM9G20-EK Evaluation Kit with 2 SD/MMC Slots"
 	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
@@ -389,8 +394,8 @@ if ARCH_AT91SAM9G45
 
 comment "AT91SAM9G45 Board Type"
 
-config MACH_AT91SAM9G45EKES
-	bool "Atmel AT91SAM9G45-EKES Evaluation Kit"
+config MACH_AT91SAM9M10G45EK
+	bool "Atmel AT91SAM9M10G45-EK Evaluation Kits"
 	select HAVE_NAND_ATMEL_BUSWIDTH_16
 	help
 	  Select this if you are using Atmel's AT91SAM9G45-EKES Evaluation Kit.
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 7cbe06d7cee..412b3a471a4 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -62,7 +62,6 @@ obj-$(CONFIG_MACH_AT91SAM9RLEK)	+= board-sam9rlek.o
 
 # AT91SAM9G20 board-specific support
 obj-$(CONFIG_MACH_AT91SAM9G20EK) += board-sam9g20ek.o
-obj-$(CONFIG_MACH_AT91SAM9G20EK_2MMC) += board-sam9g20ek-2slot-mmc.o
 obj-$(CONFIG_MACH_CPU9G20)	+= board-cpu9krea.o
 obj-$(CONFIG_MACH_STAMP9G20)	+= board-stamp9g20.o
 obj-$(CONFIG_MACH_PORTUXG20)	+= board-stamp9g20.o
@@ -71,7 +70,7 @@ obj-$(CONFIG_MACH_PORTUXG20)	+= board-stamp9g20.o
 obj-$(CONFIG_MACH_SNAPPER_9260)	+= board-snapper9260.o
 
 # AT91SAM9G45 board-specific support
-obj-$(CONFIG_MACH_AT91SAM9G45EKES) += board-sam9m10g45ek.o
+obj-$(CONFIG_MACH_AT91SAM9M10G45EK) += board-sam9m10g45ek.o
 
 # AT91CAP9 board-specific support
 obj-$(CONFIG_MACH_AT91CAP9ADK)	+= board-cap9adk.o
diff --git a/arch/arm/mach-at91/board-at572d940hf_ek.c b/arch/arm/mach-at91/board-at572d940hf_ek.c
index 5daff277f53..46651623f20 100644
--- a/arch/arm/mach-at91/board-at572d940hf_ek.c
+++ b/arch/arm/mach-at91/board-at572d940hf_ek.c
@@ -216,7 +216,7 @@ static struct atmel_nand_data __initdata eb_nand_data = {
 /*	.rdy_pin	= AT91_PIN_PC16, */
 	.enable_pin	= AT91_PIN_PA15,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
 	.bus_width_16	= 1,
 #else
 	.bus_width_16	= 0,
diff --git a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c b/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c
deleted file mode 100644
index c49f5c003ee..00000000000
--- a/arch/arm/mach-at91/board-sam9g20ek-2slot-mmc.c
+++ /dev/null
@@ -1,329 +0,0 @@
-/*
- *  Copyright (C) 2005 SAN People
- *  Copyright (C) 2008 Atmel
- *  Copyright (C) 2009 Rob Emanuele
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-
-#include <linux/types.h>
-#include <linux/init.h>
-#include <linux/mm.h>
-#include <linux/module.h>
-#include <linux/platform_device.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/at73c213.h>
-#include <linux/clk.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/consumer.h>
-
-#include <mach/hardware.h>
-#include <asm/setup.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-
-#include <mach/board.h>
-#include <mach/gpio.h>
-#include <mach/at91sam9_smc.h>
-
-#include "sam9_smc.h"
-#include "generic.h"
-
-
-static void __init ek_map_io(void)
-{
-	/* Initialize processor: 18.432 MHz crystal */
-	at91sam9260_initialize(18432000);
-
-	/* DGBU on ttyS0. (Rx & Tx only) */
-	at91_register_uart(0, 0, 0);
-
-	/* USART0 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
-	at91_register_uart(AT91SAM9260_ID_US0, 1, ATMEL_UART_CTS | ATMEL_UART_RTS
-			   | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD
-			   | ATMEL_UART_RI);
-
-	/* USART1 on ttyS2. (Rx, Tx, RTS, CTS) */
-	at91_register_uart(AT91SAM9260_ID_US1, 2, ATMEL_UART_CTS | ATMEL_UART_RTS);
-
-	/* set serial console to ttyS0 (ie, DBGU) */
-	at91_set_serial_console(0);
-}
-
-static void __init ek_init_irq(void)
-{
-	at91sam9260_init_interrupts(NULL);
-}
-
-
-/*
- * USB Host port
- */
-static struct at91_usbh_data __initdata ek_usbh_data = {
-	.ports		= 2,
-};
-
-/*
- * USB Device port
- */
-static struct at91_udc_data __initdata ek_udc_data = {
-	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
-};
-
-
-/*
- * SPI devices.
- */
-static struct spi_board_info ek_spi_devices[] = {
-#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91))
-	{	/* DataFlash chip */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 1,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
-	{	/* DataFlash card */
-		.modalias	= "mtd_dataflash",
-		.chip_select	= 0,
-		.max_speed_hz	= 15 * 1000 * 1000,
-		.bus_num	= 0,
-	},
-#endif
-#endif
-};
-
-
-/*
- * MACB Ethernet device
- */
-static struct at91_eth_data __initdata ek_macb_data = {
-	.phy_irq_pin	= AT91_PIN_PB0,
-	.is_rmii	= 1,
-};
-
-
-/*
- * NAND flash
- */
-static struct mtd_partition __initdata ek_nand_partition[] = {
-	{
-		.name   = "Bootstrap",
-		.offset = 0,
-		.size   = 4 * SZ_1M,
-	},
-	{
-		.name	= "Partition 1",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= 60 * SZ_1M,
-	},
-	{
-		.name	= "Partition 2",
-		.offset	= MTDPART_OFS_NXTBLK,
-		.size	= MTDPART_SIZ_FULL,
-	},
-};
-
-static struct mtd_partition * __init nand_partitions(int size, int *num_partitions)
-{
-	*num_partitions = ARRAY_SIZE(ek_nand_partition);
-	return ek_nand_partition;
-}
-
-/* det_pin is not connected */
-static struct atmel_nand_data __initdata ek_nand_data = {
-	.ale		= 21,
-	.cle		= 22,
-	.rdy_pin	= AT91_PIN_PC13,
-	.enable_pin	= AT91_PIN_PC14,
-	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
-	.bus_width_16	= 1,
-#else
-	.bus_width_16	= 0,
-#endif
-};
-
-static struct sam9_smc_config __initdata ek_nand_smc_config = {
-	.ncs_read_setup		= 0,
-	.nrd_setup		= 2,
-	.ncs_write_setup	= 0,
-	.nwe_setup		= 2,
-
-	.ncs_read_pulse		= 4,
-	.nrd_pulse		= 4,
-	.ncs_write_pulse	= 4,
-	.nwe_pulse		= 4,
-
-	.read_cycle		= 7,
-	.write_cycle		= 7,
-
-	.mode			= AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
-	.tdf_cycles		= 3,
-};
-
-static void __init ek_add_device_nand(void)
-{
-	/* setup bus-width (8 or 16) */
-	if (ek_nand_data.bus_width_16)
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
-	else
-		ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
-
-	/* configure chip-select 3 (NAND) */
-	sam9_smc_configure(3, &ek_nand_smc_config);
-
-	at91_add_device_nand(&ek_nand_data);
-}
-
-
-/*
- * MCI (SD/MMC)
- * wp_pin is not connected
- */
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
-static struct mci_platform_data __initdata ek_mmc_data = {
-	.slot[0] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PC2,
-		.wp_pin		= -ENODEV,
-	},
-	.slot[1] = {
-		.bus_width	= 4,
-		.detect_pin	= AT91_PIN_PC9,
-		.wp_pin		= -ENODEV,
-	},
-
-};
-#else
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.slot_b		= 1,	/* Only one slot so use slot B */
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PC9,
-};
-#endif
-
-/*
- * LEDs
- */
-static struct gpio_led ek_leds[] = {
-	{	/* "bottom" led, green, userled1 to be defined */
-		.name			= "ds5",
-		.gpio			= AT91_PIN_PB8,
-		.active_low		= 1,
-		.default_trigger	= "none",
-	},
-	{	/* "power" led, yellow */
-		.name			= "ds1",
-		.gpio			= AT91_PIN_PB9,
-		.default_trigger	= "heartbeat",
-	}
-};
-
-#if defined(CONFIG_REGULATOR_FIXED_VOLTAGE) || defined(CONFIG_REGULATOR_FIXED_VOLTAGE_MODULE)
-static struct regulator_consumer_supply ek_audio_consumer_supplies[] = {
-	REGULATOR_SUPPLY("AVDD", "0-001b"),
-	REGULATOR_SUPPLY("HPVDD", "0-001b"),
-	REGULATOR_SUPPLY("DBVDD", "0-001b"),
-	REGULATOR_SUPPLY("DCVDD", "0-001b"),
-};
-
-static struct regulator_init_data ek_avdd_reg_init_data = {
-	.constraints	= {
-		.name	= "3V3",
-		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-	},
-	.consumer_supplies = ek_audio_consumer_supplies,
-	.num_consumer_supplies = ARRAY_SIZE(ek_audio_consumer_supplies),
-};
-
-static struct fixed_voltage_config ek_vdd_pdata = {
-	.supply_name	= "board-3V3",
-	.microvolts	= 3300000,
-	.gpio		= -EINVAL,
-	.enabled_at_boot = 0,
-	.init_data	= &ek_avdd_reg_init_data,
-};
-static struct platform_device ek_voltage_regulator = {
-	.name		= "reg-fixed-voltage",
-	.id		= -1,
-	.num_resources	= 0,
-	.dev		= {
-		.platform_data	= &ek_vdd_pdata,
-	},
-};
-static void __init ek_add_regulators(void)
-{
-	platform_device_register(&ek_voltage_regulator);
-}
-#else
-static void __init ek_add_regulators(void) {}
-#endif
-
-static struct i2c_board_info __initdata ek_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("24c512", 0x50),
-	},
-};
-
-
-static void __init ek_board_init(void)
-{
-	/* Serial */
-	at91_add_device_serial();
-	/* USB Host */
-	at91_add_device_usbh(&ek_usbh_data);
-	/* USB Device */
-	at91_add_device_udc(&ek_udc_data);
-	/* SPI */
-	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
-	/* NAND */
-	ek_add_device_nand();
-	/* Ethernet */
-	at91_add_device_eth(&ek_macb_data);
-	/* Regulators */
-	ek_add_regulators();
-	/* MMC */
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
-	at91_add_device_mci(0, &ek_mmc_data);
-#else
-	at91_add_device_mmc(0, &ek_mmc_data);
-#endif
-	/* I2C */
-	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
-	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
-	/* PCK0 provides MCLK to the WM8731 */
-	at91_set_B_periph(AT91_PIN_PC1, 0);
-	/* SSC (for WM8731) */
-	at91_add_device_ssc(AT91SAM9260_ID_SSC, ATMEL_SSC_TX);
-}
-
-MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod")
-	/* Maintainer: Rob Emanuele */
-	.phys_io	= AT91_BASE_SYS,
-	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
-	.boot_params	= AT91_SDRAM_BASE + 0x100,
-	.timer		= &at91sam926x_timer,
-	.map_io		= ek_map_io,
-	.init_irq	= ek_init_irq,
-	.init_machine	= ek_board_init,
-MACHINE_END
diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c
index 6ea9808b886..b463e340c4a 100644
--- a/arch/arm/mach-at91/board-sam9g20ek.c
+++ b/arch/arm/mach-at91/board-sam9g20ek.c
@@ -47,6 +47,18 @@
 #include "sam9_smc.h"
 #include "generic.h"
 
+/*
+ * board revision encoding
+ * bit 0:
+ * 	0 => 1 sd/mmc slot
+ * 	1 => 2 sd/mmc slots connectors (board from revision C)
+ */
+#define HAVE_2MMC	(1 << 0)
+static int inline ek_have_2mmc(void)
+{
+	return machine_is_at91sam9g20ek_2mmc() || (system_rev & HAVE_2MMC);
+}
+
 
 static void __init ek_map_io(void)
 {
@@ -94,7 +106,7 @@ static struct at91_udc_data __initdata ek_udc_data = {
  * SPI devices.
  */
 static struct spi_board_info ek_spi_devices[] = {
-#if !defined(CONFIG_MMC_AT91)
+#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91))
 	{	/* DataFlash chip */
 		.modalias	= "mtd_dataflash",
 		.chip_select	= 1,
@@ -121,6 +133,13 @@ static struct at91_eth_data __initdata ek_macb_data = {
 	.is_rmii	= 1,
 };
 
+static void __init ek_add_device_macb(void)
+{
+	if (ek_have_2mmc())
+		ek_macb_data.phy_irq_pin = AT91_PIN_PB0;
+
+	at91_add_device_eth(&ek_macb_data);
+}
 
 /*
  * NAND flash
@@ -198,13 +217,36 @@ static void __init ek_add_device_nand(void)
 
 /*
  * MCI (SD/MMC)
- * det_pin, wp_pin and vcc_pin are not connected
+ * wp_pin and vcc_pin are not connected
  */
+#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
+static struct mci_platform_data __initdata ek_mmc_data = {
+	.slot[1] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PC9,
+	},
+
+};
+#else
 static struct at91_mmc_data __initdata ek_mmc_data = {
-	.slot_b		= 1,
+	.slot_b		= 1,	/* Only one slot so use slot B */
 	.wire4		= 1,
+	.det_pin	= AT91_PIN_PC9,
 };
+#endif
 
+static void __init ek_add_device_mmc(void)
+{
+#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
+	if (ek_have_2mmc()) {
+		ek_mmc_data.slot[0].bus_width = 4;
+		ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
+	}
+	at91_add_device_mci(0, &ek_mmc_data);
+#else
+	at91_add_device_mmc(0, &ek_mmc_data);
+#endif
+}
 
 /*
  * LEDs
@@ -223,6 +265,15 @@ static struct gpio_led ek_leds[] = {
 	}
 };
 
+static void __init ek_add_device_gpio_leds(void)
+{
+	if (ek_have_2mmc()) {
+		ek_leds[0].gpio = AT91_PIN_PB8;
+		ek_leds[1].gpio = AT91_PIN_PB9;
+	}
+
+	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+}
 
 /*
  * GPIO Buttons
@@ -336,15 +387,15 @@ static void __init ek_board_init(void)
 	/* NAND */
 	ek_add_device_nand();
 	/* Ethernet */
-	at91_add_device_eth(&ek_macb_data);
+	ek_add_device_macb();
 	/* Regulators */
 	ek_add_regulators();
 	/* MMC */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	ek_add_device_mmc();
 	/* I2C */
 	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
 	/* LEDs */
-	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
+	ek_add_device_gpio_leds();
 	/* Push Buttons */
 	ek_add_device_buttons();
 	/* PCK0 provides MCLK to the WM8731 */
@@ -363,3 +414,14 @@ MACHINE_START(AT91SAM9G20EK, "Atmel AT91SAM9G20-EK")
 	.init_irq	= ek_init_irq,
 	.init_machine	= ek_board_init,
 MACHINE_END
+
+MACHINE_START(AT91SAM9G20EK_2MMC, "Atmel AT91SAM9G20-EK 2 MMC Slot Mod")
+	/* Maintainer: Atmel */
+	.phys_io	= AT91_BASE_SYS,
+	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
+	.boot_params	= AT91_SDRAM_BASE + 0x100,
+	.timer		= &at91sam926x_timer,
+	.map_io		= ek_map_io,
+	.init_irq	= ek_init_irq,
+	.init_machine	= ek_board_init,
+MACHINE_END
diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index ee800595594..ae0e0843e5f 100644
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -135,7 +135,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
 	.partition_info	= nand_partitions,
-#if defined(CONFIG_MTD_NAND_AT91_BUSWIDTH_16)
+#if defined(CONFIG_MTD_NAND_ATMEL_BUSWIDTH_16)
 	.bus_width_16	= 1,
 #else
 	.bus_width_16	= 0,
@@ -399,7 +399,7 @@ static void __init ek_board_init(void)
 	at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));
 }
 
-MACHINE_START(AT91SAM9G45EKES, "Atmel AT91SAM9G45-EKES")
+MACHINE_START(AT91SAM9M10G45EK, "Atmel AT91SAM9M10G45-EK")
 	/* Maintainer: Atmel */
 	.phys_io	= AT91_BASE_SYS,
 	.io_pg_offst	= (AT91_VA_BASE_SYS >> 18) & 0xfffc,
diff --git a/arch/arm/mach-at91/include/mach/at91x40.h b/arch/arm/mach-at91/include/mach/at91x40.h
index d34cdb8abdc..063ac44a020 100644
--- a/arch/arm/mach-at91/include/mach/at91x40.h
+++ b/arch/arm/mach-at91/include/mach/at91x40.h
@@ -52,4 +52,10 @@
 #define AT91_DBGU_CIDR	(AT91_SF + 0)	/* CIDR in PS segment */
 #define AT91_DBGU_EXID	(AT91_SF + 4)	/* EXID in PS segment */
 
+/*
+ * Support defines for the simple Power Controller module.
+ */
+#define	AT91_PS_CR	(AT91_PS + 0)	/* PS Control register */
+#define	AT91_PS_CR_CPU	(1 << 0)	/* CPU clock disable bit */
+
 #endif /* AT91X40_H */
diff --git a/arch/arm/mach-at91/include/mach/system.h b/arch/arm/mach-at91/include/mach/system.h
index c80e090b367..36af14bc13b 100644
--- a/arch/arm/mach-at91/include/mach/system.h
+++ b/arch/arm/mach-at91/include/mach/system.h
@@ -28,17 +28,20 @@
 
 static inline void arch_idle(void)
 {
-#ifndef CONFIG_DEBUG_KERNEL
 	/*
 	 * Disable the processor clock.  The processor will be automatically
 	 * re-enabled by an interrupt or by a reset.
 	 */
-	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+#ifdef AT91_PS
+	at91_sys_write(AT91_PS_CR, AT91_PS_CR_CPU);
 #else
+	at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
+#endif
+#ifndef CONFIG_CPU_ARM920T
 	/*
 	 * Set the processor (CP15) into 'Wait for Interrupt' mode.
-	 * Unlike disabling the processor clock via the PMC (above)
-	 *  this allows the processor to be woken via JTAG.
+	 * Post-RM9200 processors need this in conjunction with the above
+	 * to save power when idle.
 	 */
 	cpu_do_idle();
 #endif