Remove long-unmaintained ftape driver subsystem.

It's bitrotten, long unmaintained, long hidden under BROKEN_ON_SMP,
etc.  As scheduled in feature-removal-schedule.txt, and ack'd several
times on lkml.

Signed-off-by: Jeff Garzik <jeff@garzik.org>

4 files changed, 0 insertions, 320 deletions

diff --git a/Documentation/00-INDEX b/Documentation/00-INDEX
index 02457ec9c94..f08ca953573 100644
--- a/Documentation/00-INDEX
+++ b/Documentation/00-INDEX
@@ -104,8 +104,6 @@ firmware_class/
 	- request_firmware() hotplug interface info.
 floppy.txt
 	- notes and driver options for the floppy disk driver.
-ftape.txt
-	- notes about the floppy tape device driver.
 hayes-esp.txt
 	- info on using the Hayes ESP serial driver.
 highuid.txt
diff --git a/Documentation/feature-removal-schedule.txt b/Documentation/feature-removal-schedule.txt
index f81819364b7..226ecf2ffd5 100644
--- a/Documentation/feature-removal-schedule.txt
+++ b/Documentation/feature-removal-schedule.txt
@@ -234,14 +234,6 @@ Who:	Jean Delvare <khali@linux-fr.org>
 
 ---------------------------
 
-What:	ftape
-When:	2.6.20
-Why:	Orphaned for ages.  SMP bugs long unfixed.  Few users left
-	in the world.
-Who:	Jeff Garzik <jeff@garzik.org>
-
----------------------------
-
 What:	IPv4 only connection tracking/NAT/helpers
 When:	2.6.22
 Why:	The new layer 3 independant connection tracking replaces the old
diff --git a/Documentation/ftape.txt b/Documentation/ftape.txt
deleted file mode 100644
index 7d8bb338403..00000000000
--- a/Documentation/ftape.txt
+++ /dev/null
@@ -1,307 +0,0 @@
-Intro
-=====
-
-This file describes some issues involved when using the "ftape"
-floppy tape device driver that comes with the Linux kernel.
-
-ftape has a home page at
-
-http://ftape.dot-heine.de/
-
-which contains further information about ftape. Please cross check
-this WWW address against the address given (if any) in the MAINTAINERS
-file located in the top level directory of the Linux kernel source
-tree.
-
-NOTE: This is an unmaintained set of drivers, and it is not guaranteed to work.
-If you are interested in taking over maintenance, contact Claus-Justus Heine
-<ch@dot-heine.de>, the former maintainer.
-
-Contents
-========
-
-A minus 1: Ftape documentation
-
-A. Changes
-   1. Goal
-   2. I/O Block Size
-   3. Write Access when not at EOD (End Of Data) or BOT (Begin Of Tape)
-   4. Formatting
-   5. Interchanging cartridges with other operating systems
-
-B. Debugging Output
-   1. Introduction
-   2. Tuning the debugging output
-
-C. Boot and load time configuration
-   1. Setting boot time parameters
-   2. Module load time parameters
-   3. Ftape boot- and load time options
-   4. Example kernel parameter setting
-   5. Example module parameter setting
-
-D. Support and contacts
-
-*******************************************************************************
-
-A minus 1. Ftape documentation
-==============================
-
-Unluckily, the ftape-HOWTO is out of date. This really needs to be
-changed. Up to date documentation as well as recent development
-versions of ftape and useful links to related topics can be found at
-the ftape home page at
-
-http://ftape.dot-heine.de/
-
-*******************************************************************************
-
-A. Changes
-==========
-
-1. Goal
-   ~~~~
-   The goal of all that incompatibilities was to give ftape an interface
-   that resembles the interface provided by SCSI tape drives as close
-   as possible. Thus any Unix backup program that is known to work
-   with SCSI tape drives should also work.
-
-   The concept of a fixed block size for read/write transfers is
-   rather unrelated to this SCSI tape compatibility at the file system
-   interface level. It developed out of a feature of zftape, a
-   block wise user transparent on-the-fly compression. That compression
-   support will not be dropped in future releases for compatibility
-   reasons with previous releases of zftape.
-
-2. I/O Block Size
-   ~~~~~~~~~~~~~~
-   The block size defaults to 10k which is the default block size of
-   GNU tar.
-
-   The block size can be tuned either during kernel configuration or
-   at runtime with the MTIOCTOP ioctl using the MTSETBLK operation
-   (i.e. do "mt -f /dev/qft0" setblk #BLKSZ). A block size of 0
-   switches to variable block size mode i.e. "mt setblk 0" switches
-   off the block size restriction. However, this disables zftape's
-   built in on-the-fly compression which doesn't work with variable
-   block size mode.
-
-   The BLKSZ parameter must be given as a byte count and must be a
-   multiple of 32k or 0, i.e. use "mt setblk 32768" to switch to a
-   block size of 32k.
-
-   The typical symptom of a block size mismatch is an "invalid
-   argument" error message.
-
-3. Write Access when not at EOD (End Of Data) or BOT (Begin Of Tape)
-   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-   zftape (the file system interface of ftape-3.x) denies write access
-   to the tape cartridge when it isn't positioned either at BOT or
-   EOD.
-
-4. Formatting
-   ~~~~~~~~~~
-   ftape DOES support formatting of floppy tape cartridges. You need the
-   `ftformat' program that is shipped with the modules version of ftape.
-   Please get the latest version of ftape from
-
-   ftp://sunsite.unc.edu/pub/Linux/kernel/tapes
-
-   or from the ftape home page at
-
-   http://ftape.dot-heine.de/
-
-   `ftformat' is contained in the `./contrib/' subdirectory of that
-   separate ftape package.
-
-5. Interchanging cartridges with other operating systems
-   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-   The internal emulation of Unix tape device file marks has changed
-   completely. ftape now uses the volume table segment as specified
-   by the QIC-40/80/3010/3020/113 standards to emulate file marks. As
-   a consequence there is limited support to interchange cartridges
-   with other operating systems.
-
-   To be more precise: ftape will detect volumes written by other OS's
-   programs and other OS's programs will detect volumes written by
-   ftape.
-
-   However, it isn't possible to extract the data dumped to the tape
-   by some MSDOS program with ftape. This exceeds the scope of a
-   kernel device driver. If you need such functionality, then go ahead
-   and write a user space utility that is able to do that. ftape already
-   provides all kernel level support necessary to do that.
-
-*******************************************************************************
-
-B. Debugging Output
-   ================
-
-1. Introduction
-   ~~~~~~~~~~~~
-   The ftape driver can be very noisy in that is can print lots of
-   debugging messages to the kernel log files and the system console.
-   While this is useful for debugging it might be annoying during
-   normal use and enlarges the size of the driver by several kilobytes.
-
-   To reduce the size of the driver you can trim the maximal amount of
-   debugging information available during kernel configuration. Please
-   refer to the kernel configuration script and its on-line help
-   functionality.
-
-   The amount of debugging output maps to the "tracing" boot time
-   option and the "ft_tracing" modules option as follows:
-
-   0              bugs
-   1              + errors (with call-stack dump)
-   2              + warnings
-   3              + information
-   4              + more information
-   5              + program flow
-   6              + fdc/dma info
-   7              + data flow
-   8              + everything else
-
-2. Tuning the debugging output
-   ~~~~~~~~~~~~~~~~~~~~~~~~~~~
-   To reduce the amount of debugging output printed to the system
-   console you can
-
-   i)  trim the debugging output at run-time with
-
-       mt -f /dev/nqft0 setdensity #DBGLVL
-
-       where "#DBGLVL" is a number between 0 and 9
-
-   ii) trim the debugging output at module load time with
-
-       modprobe ftape ft_tracing=#DBGLVL
-
-       Of course, this applies only if you have configured ftape to be
-       compiled as a module.
-
-   iii) trim the debugging output during system boot time. Add the
-       following to the kernel command line:
-
-       ftape=#DBGLVL,tracing
-
-       Please refer also to the next section if you don't know how to
-       set boot time parameters.
-
-*******************************************************************************
-
-C. Boot and load time configuration
-   ================================
-
-1. Setting boot time parameters
-   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 
-   Assuming that you use lilo, the LI)nux LO)ader, boot time kernel
-   parameters can be set by adding a line
-
-   append some_kernel_boot_time_parameter
-
-   to `/etc/lilo.conf' or at real boot time by typing in the options
-   at the prompt provided by LILO. I can't give you advice on how to
-   specify those parameters with other loaders as I don't use them.
-
-   For ftape, each "some_kernel_boot_time_parameter" looks like
-   "ftape=value,option". As an example, the debugging output can be
-   increased with
-
-   ftape=4,tracing
-
-   NOTE: the value precedes the option name.
-
-2. Module load time parameters
-   ~~~~~~~~~~~~~~~~~~~~~~~~~~~
-   Module parameters can be specified either directly when invoking
-   the program 'modprobe' at the shell prompt:
-
-   modprobe ftape ft_tracing=4
-
-   or by editing the file `/etc/modprobe.conf' in which case they take
-   effect each time when the module is loaded with `modprobe' (please
-   refer to the respective manual pages). Thus, you should add a line
-
-   options ftape ft_tracing=4
-
-   to `/etc/modprobe.conf` if you intend to increase the debugging
-   output of the driver.
-
-
-3. Ftape boot- and load time options
-   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-   i.   Controlling the amount of debugging output
-        DBGLVL has to be replaced by a number between 0 and 8.
-
-        module                 |  kernel command line
-        -----------------------|----------------------
-        ft_tracing=DBGLVL      |  ftape=DBGLVL,tracing
-
-   ii.  Hardware setup
-	BASE is the base address of your floppy disk controller,
-        IRQ and DMA give its interrupt and DMA channel, respectively.
-        BOOL is an integer, "0" means "no"; any other value means
-	"yes". You don't need to specify anything if connecting your tape
-        drive to the standard floppy disk controller. All of these
-	values have reasonable defaults. The defaults can be modified
-	during kernel configuration, i.e. while running "make config",
-	"make menuconfig" or "make xconfig" in the top level directory
-	of the Linux kernel source tree. Please refer also to the on
-	line documentation provided during that kernel configuration
-	process.
-
-	ft_probe_fc10 is set to a non-zero value if you wish for ftape to
-	probe for a Colorado FC-10 or FC-20 controller.
-
-	ft_mach2 is set to a non-zero value if you wish for ftape to probe
-	for a Mountain MACH-2 controller.
-
-        module                 |  kernel command line
-        -----------------------|----------------------
-        ft_fdc_base=BASE       |  ftape=BASE,ioport
-        ft_fdc_irq=IRQ         |  ftape=IRQ,irq
-        ft_fdc_dma=DMA         |  ftape=DMA,dma
-        ft_probe_fc10=BOOL     |  ftape=BOOL,fc10
-        ft_mach2=BOOL          |  ftape=BOOL,mach2
-        ft_fdc_threshold=THR   |  ftape=THR,threshold
-        ft_fdc_rate_limit=RATE |  ftape=RATE,datarate
-
-4. Example kernel parameter setting
-   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 
-   To configure ftape to probe for a Colorado FC-10/FC-20 controller
-   and to increase the amount of debugging output a little bit, add
-   the following line to `/etc/lilo.conf':
-
-   append ftape=1,fc10 ftape=4,tracing
-
-5. Example module parameter setting
-   ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-   To do the same, but with ftape compiled as a loadable kernel
-   module, add the following line to `/etc/modprobe.conf':
-
-   options ftape ft_probe_fc10=1 ft_tracing=4
-
-*******************************************************************************
-
-D. Support and contacts
-   ====================
-
-   Ftape is distributed under the GNU General Public License. There is
-   absolutely no warranty for this software. However, you can reach
-   the current maintainer of the ftape package under the email address
-   given in the MAINTAINERS file which is located in the top level
-   directory of the Linux kernel source tree. There you'll find also
-   the relevant mailing list to use as a discussion forum and the web
-   page to query for the most recent documentation, related work and
-   development versions of ftape.
-
-   Changelog:
-   ==========
-
-~1996:		Original Document
-
-10-24-2004:	General cleanup and updating, noting additional module options.
-		James Nelson <james4765@gmail.com>
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 67473849f20..15e4fed127f 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -557,9 +557,6 @@ and is between 256 and 4096 characters. It is defined in the file
 	floppy=		[HW]
 			See Documentation/floppy.txt.
 
-	ftape=		[HW] Floppy Tape subsystem debugging options.
-			See Documentation/ftape.txt.
-
 	gamecon.map[2|3]=
 			[HW,JOY] Multisystem joystick and NES/SNES/PSX pad
 			support via parallel port (up to 5 devices per port)