Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
 "These are mostly new device tree bindings for existing drivers, as
  well as changes to the device tree source files to add support for
  those devices, and a couple of new boards, most notably Samsung's
  Exynos5 based Chromebook.

  The changes depend on earlier platform specific updates and touch the
  usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."

* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
  ARM: exynos: dts: cros5250: add EC device
  ARM: dts: Add sbs-battery for exynos5250-snow
  ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
  ARM: dts: add mshc controller node for Exynos4x12 SoCs
  ARM: dts: Add chip-id controller node on Exynos4/5 SoC
  ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
  ARM: davinci: da850-evm: add SPI flash support
  ARM: davinci: da850: override SPI DT node device name
  ARM: davinci: da850: add SPI1 DT node
  spi/davinci: add DT binding documentation
  spi/davinci: no wildcards in DT compatible property
  ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
  ARM: dts: mvebu: introduce internal-regs node
  ARM: dts: mvebu: Convert all the mvebu files to use the range property
  ARM: dts: mvebu: move all peripherals inside soc
  ARM: dts: mvebu: fix cpus section indentation
  ARM: davinci: da850: add EHRPWM & ECAP DT node
  ARM/dts: OMAP3: fix pinctrl-single configuration
  ARM: dts: Add OMAP3430 SDP NOR flash memory binding
  ARM: dts: Add NOR flash bindings for OMAP2420 H4
  ...

23 files changed, 396 insertions, 41 deletions

diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
index 6888a5efc86..c0105de55cb 100644
--- a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
+++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
@@ -6,6 +6,7 @@ provided by Arteris.
 Required properties:
 - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family
                Should be "ti,omap4-l3-noc" for OMAP4 family
+- reg:	Contains L3 register address range for each noc domain.
 - ti,hwmods: "l3_main_1", ... One hwmod for each noc domain.
 
 Examples:
diff --git a/Documentation/devicetree/bindings/arm/omap/timer.txt b/Documentation/devicetree/bindings/arm/omap/timer.txt
index 8732d4d41f8..d02e27c764e 100644
--- a/Documentation/devicetree/bindings/arm/omap/timer.txt
+++ b/Documentation/devicetree/bindings/arm/omap/timer.txt
@@ -1,7 +1,20 @@
 OMAP Timer bindings
 
 Required properties:
-- compatible:		Must be "ti,omap2-timer" for OMAP2+ controllers.
+- compatible:		Should be set to one of the below. Please note that
+			OMAP44xx devices have timer instances that are 100%
+			register compatible with OMAP3xxx devices as well as
+			newer timers that are not 100% register compatible.
+			So for OMAP44xx devices timer instances may use
+			different compatible strings.
+
+			ti,omap2420-timer (applicable to OMAP24xx devices)
+			ti,omap3430-timer (applicable to OMAP3xxx/44xx devices)
+			ti,omap4430-timer (applicable to OMAP44xx devices)
+			ti,omap5430-timer (applicable to OMAP543x devices)
+			ti,am335x-timer	(applicable to AM335x devices)
+			ti,am335x-timer-1ms (applicable to AM335x devices)
+
 - reg:			Contains timer register address range (base address and
 			length).
 - interrupts: 		Contains the interrupt information for the timer. The
@@ -22,7 +35,7 @@ Optional properties:
 Example:
 
 timer12: timer@48304000 {
-	compatible = "ti,omap2-timer";
+	compatible = "ti,omap3430-timer";
 	reg = <0x48304000 0x400>;
 	interrupts = <95>;
 	ti,hwmods = "timer12"
diff --git a/Documentation/devicetree/bindings/arm/samsung/sysreg.txt b/Documentation/devicetree/bindings/arm/samsung/sysreg.txt
new file mode 100644
index 00000000000..5039c0a12f5
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/samsung/sysreg.txt
@@ -0,0 +1,7 @@
+SAMSUNG S5P/Exynos SoC series System Registers (SYSREG)
+
+Properties:
+ - name : should be 'sysreg';
+ - compatible : should contain "samsung,<chip name>-sysreg", "syscon";
+   For Exynos4 SoC series it should be "samsung,exynos4-sysreg", "syscon";
+ - reg : offset and length of the register set.
diff --git a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
index ded0398d3bd..a4873e5e3e3 100644
--- a/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
+++ b/Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt
@@ -3,17 +3,58 @@
 Required properties:
 - compatible : Should be "fsl,<chip>-dma-apbh" or "fsl,<chip>-dma-apbx"
 - reg : Should contain registers location and length
+- interrupts : Should contain the interrupt numbers of DMA channels.
+  If a channel is empty/reserved, 0 should be filled in place.
+- #dma-cells : Must be <1>.  The number cell specifies the channel ID.
+- dma-channels : Number of channels supported by the DMA controller
+
+Optional properties:
+- interrupt-names : Name of DMA channel interrupts
 
 Supported chips:
 imx23, imx28.
 
 Examples:
-dma-apbh@80004000 {
+
+dma_apbh: dma-apbh@80004000 {
 	compatible = "fsl,imx28-dma-apbh";
-	reg = <0x80004000 2000>;
+	reg = <0x80004000 0x2000>;
+	interrupts = <82 83 84 85
+		      88 88 88 88
+		      88 88 88 88
+		      87 86 0 0>;
+	interrupt-names = "ssp0", "ssp1", "ssp2", "ssp3",
+			  "gpmi0", "gmpi1", "gpmi2", "gmpi3",
+			  "gpmi4", "gmpi5", "gpmi6", "gmpi7",
+			  "hsadc", "lcdif", "empty", "empty";
+	#dma-cells = <1>;
+	dma-channels = <16>;
 };
 
-dma-apbx@80024000 {
+dma_apbx: dma-apbx@80024000 {
 	compatible = "fsl,imx28-dma-apbx";
-	reg = <0x80024000 2000>;
+	reg = <0x80024000 0x2000>;
+	interrupts = <78 79 66 0
+		      80 81 68 69
+		      70 71 72 73
+		      74 75 76 77>;
+	interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+			  "saif0", "saif1", "i2c0", "i2c1",
+			  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
+			  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";
+	#dma-cells = <1>;
+	dma-channels = <16>;
+};
+
+DMA clients connected to the MXS DMA controller must use the format
+described in the dma.txt file.
+
+Examples:
+
+auart0: serial@8006a000 {
+	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
+	reg = <0x8006a000 0x2000>;
+	interrupts = <112>;
+	dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+	dma-names = "rx", "tx";
 };
diff --git a/Documentation/devicetree/bindings/fb/mxsfb.txt b/Documentation/devicetree/bindings/fb/mxsfb.txt
index b41e5e52a67..96ec5179c8a 100644
--- a/Documentation/devicetree/bindings/fb/mxsfb.txt
+++ b/Documentation/devicetree/bindings/fb/mxsfb.txt
@@ -5,9 +5,16 @@ Required properties:
   imx23 and imx28.
 - reg: Address and length of the register set for lcdif
 - interrupts: Should contain lcdif interrupts
+- display : phandle to display node (see below for details)
 
-Optional properties:
-- panel-enable-gpios : Should specify the gpio for panel enable
+* display node
+
+Required properties:
+- bits-per-pixel : <16> for RGB565, <32> for RGB888/666.
+- bus-width : number of data lines.  Could be <8>, <16>, <18> or <24>.
+
+Required sub-node:
+- display-timings : Refer to binding doc display-timing.txt for details.
 
 Examples:
 
@@ -15,5 +22,28 @@ lcdif@80030000 {
 	compatible = "fsl,imx28-lcdif";
 	reg = <0x80030000 2000>;
 	interrupts = <38 86>;
-	panel-enable-gpios = <&gpio3 30 0>;
+
+	display: display {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <33500000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <164>;
+				hback-porch = <89>;
+				hsync-len = <10>;
+				vback-porch = <23>;
+				vfront-porch = <10>;
+				vsync-len = <10>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
 };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-omap.txt b/Documentation/devicetree/bindings/gpio/gpio-omap.txt
index 1b524c0c79f..8d950522e7f 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-omap.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-omap.txt
@@ -5,12 +5,12 @@ Required properties:
   - "ti,omap2-gpio" for OMAP2 controllers
   - "ti,omap3-gpio" for OMAP3 controllers
   - "ti,omap4-gpio" for OMAP4 controllers
+- gpio-controller : Marks the device node as a GPIO controller.
 - #gpio-cells : Should be two.
   - first cell is the pin number
   - second cell is used to specify optional parameters (unused)
-- gpio-controller : Marks the device node as a GPIO controller.
+- interrupt-controller: Mark the device node as an interrupt controller.
 - #interrupt-cells : Should be 2.
-- interrupt-controller: Mark the device node as an interrupt controller
   The first cell is the GPIO number.
   The second cell is used to specify flags:
     bits[3:0] trigger type and level flags:
@@ -32,8 +32,8 @@ Example:
 gpio4: gpio4 {
     compatible = "ti,omap4-gpio";
     ti,hwmods = "gpio4";
-    #gpio-cells = <2>;
     gpio-controller;
-    #interrupt-cells = <2>;
+    #gpio-cells = <2>;
     interrupt-controller;
+    #interrupt-cells = <2>;
 };
diff --git a/Documentation/devicetree/bindings/gpu/samsung-g2d.txt b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt
new file mode 100644
index 00000000000..2b14a940eb7
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpu/samsung-g2d.txt
@@ -0,0 +1,20 @@
+* Samsung 2D Graphics Accelerator
+
+Required properties:
+  - compatible : value should be one among the following:
+	(a) "samsung,s5pv210-g2d" for G2D IP present in S5PV210 & Exynos4210 SoC
+	(b) "samsung,exynos4212-g2d" for G2D IP present in Exynos4x12 SoCs
+	(c) "samsung,exynos5250-g2d" for G2D IP present in Exynos5250 SoC
+
+  - reg : Physical base address of the IP registers and length of memory
+	  mapped region.
+
+  - interrupts : G2D interrupt number to the CPU.
+
+Example:
+	g2d@12800000 {
+		compatible = "samsung,s5pv210-g2d";
+		reg = <0x12800000 0x1000>;
+		interrupts = <0 89 0>;
+		status = "disabled";
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
index 7a3fe9e5f4c..4e1c8ac01eb 100644
--- a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
+++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
@@ -3,10 +3,13 @@
 Required properties:
 - compatible: Should be "fsl,<chip>-i2c"
 - reg: Should contain registers location and length
-- interrupts: Should contain ERROR and DMA interrupts
+- interrupts: Should contain ERROR interrupt number
 - clock-frequency: Desired I2C bus clock frequency in Hz.
                    Only 100000Hz and 400000Hz modes are supported.
-- fsl,i2c-dma-channel: APBX DMA channel for the I2C
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and I2C DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
 
 Examples:
 
@@ -15,7 +18,8 @@ i2c0: i2c@80058000 {
 	#size-cells = <0>;
 	compatible = "fsl,imx28-i2c";
 	reg = <0x80058000 2000>;
-	interrupts = <111 68>;
+	interrupts = <111>;
 	clock-frequency = <100000>;
-	fsl,i2c-dma-channel = <6>;
+	dmas = <&dma_apbx 6>;
+	dma-names = "rx-tx";
 };
diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt
new file mode 100644
index 00000000000..ef77cc7a0e4
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt
@@ -0,0 +1,60 @@
+NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver.
+
+Required properties:
+- compatible : should be:
+	"nvidia,tegra114-i2c"
+	"nvidia,tegra30-i2c"
+	"nvidia,tegra20-i2c"
+	"nvidia,tegra20-i2c-dvc"
+  Details of compatible are as follows:
+  nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C
+	controller. This only support master mode of I2C communication. Register
+	interface/offset and interrupts handling are different than generic I2C
+	controller. Driver of DVC I2C controller is only compatible with
+	"nvidia,tegra20-i2c-dvc".
+  nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support
+	master and slave mode of I2C communication. The i2c-tegra driver only
+	support master mode of I2C communication. Driver of I2C controller is
+	only compatible with "nvidia,tegra20-i2c".
+  nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is
+	very much similar to Tegra20 I2C controller with additional feature:
+	Continue Transfer Support. This feature helps to implement M_NO_START
+	as per I2C core API transfer flags. Driver of I2C controller is
+	compatible with "nvidia,tegra30-i2c" to enable the continue transfer
+	support. This is also compatible with "nvidia,tegra20-i2c" without
+	continue transfer support.
+  nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is
+	very much similar to Tegra30 I2C controller with some hardware
+	modification:
+	 - Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and
+	   fast-clk. Tegra114 has only one clock source called as div-clk and
+	   hence clock mechanism is changed in I2C controller.
+	 - Tegra30/Tegra20 I2C controller has enabled per packet transfer by
+	   default and there is no way to disable it. Tegra114 has this
+	   interrupt disable by default and SW need to enable explicitly.
+	Due to above changes, Tegra114 I2C driver makes incompatible with
+	previous hardware driver. Hence, tegra114 I2C controller is compatible
+	with "nvidia,tegra114-i2c".
+- reg: Should contain I2C controller registers physical address and length.
+- interrupts: Should contain I2C controller interrupts.
+- address-cells: Address cells for I2C device address.
+- size-cells: Size of the I2C device address.
+- clocks: Clock ID as per
+		Documentation/devicetree/bindings/clock/tegra<chip-id>.txt
+	for I2C controller.
+- clock-names: Name of the clock:
+	Tegra20/Tegra30 I2C controller: "div-clk and "fast-clk".
+	Tegra114 I2C controller: "div-clk".
+
+Example:
+
+	i2c@7000c000 {
+		compatible = "nvidia,tegra20-i2c";
+		reg = <0x7000c000 0x100>;
+		interrupts = <0 38 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 12>, <&tegra_car 124>;
+		clock-names = "div-clk", "fast-clk";
+		status = "disabled";
+	};
diff --git a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt
index 54949f6faed..515addc2007 100644
--- a/Documentation/devicetree/bindings/mmc/mxs-mmc.txt
+++ b/Documentation/devicetree/bindings/mmc/mxs-mmc.txt
@@ -9,15 +9,19 @@ and the properties used by the mxsmmc driver.
 Required properties:
 - compatible: Should be "fsl,<chip>-mmc".  The supported chips include
   imx23 and imx28.
-- interrupts: Should contain ERROR and DMA interrupts
-- fsl,ssp-dma-channel: APBH DMA channel for the SSP
+- interrupts: Should contain ERROR interrupt number
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and SSP DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
 
 Examples:
 
 ssp0: ssp@80010000 {
 	compatible = "fsl,imx28-mmc";
 	reg = <0x80010000 2000>;
-	interrupts = <96 82>;
-	fsl,ssp-dma-channel = <0>;
+	interrupts = <96>;
+	dmas = <&dma_apbh 0>;
+	dma-names = "rx-tx";
 	bus-width = <8>;
 };
diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
index 3fb3f901536..551b2a179d0 100644
--- a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt
@@ -7,10 +7,12 @@ Required properties:
   - compatible : should be "fsl,<chip>-gpmi-nand"
   - reg : should contain registers location and length for gpmi and bch.
   - reg-names: Should contain the reg names "gpmi-nand" and "bch"
-  - interrupts : The first is the DMA interrupt number for GPMI.
-                 The second is the BCH interrupt number.
-  - interrupt-names : The interrupt names "gpmi-dma", "bch";
-  - fsl,gpmi-dma-channel : Should contain the dma channel it uses.
+  - interrupts : BCH interrupt number.
+  - interrupt-names : Should be "bch".
+  - dmas: DMA specifier, consisting of a phandle to DMA controller node
+    and GPMI DMA channel ID.
+    Refer to dma.txt and fsl-mxs-dma.txt for details.
+  - dma-names: Must be "rx-tx".
 
 Optional properties:
   - nand-on-flash-bbt: boolean to enable on flash bbt option if not
@@ -27,9 +29,10 @@ gpmi-nand@8000c000 {
 	#size-cells = <1>;
 	reg = <0x8000c000 2000>, <0x8000a000 2000>;
 	reg-names = "gpmi-nand", "bch";
-	interrupts = <88>, <41>;
-	interrupt-names = "gpmi-dma", "bch";
-	fsl,gpmi-dma-channel = <4>;
+	interrupts = <41>;
+	interrupt-names = "bch";
+	dmas = <&dma_apbh 4>;
+	dma-names = "rx-tx";
 
 	partition@0 {
 	...
diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt
index f7e8e8f4d9a..3077370c89a 100644
--- a/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt
@@ -70,6 +70,10 @@ Optional subnode-properties:
     0: Disable the internal pull-up
     1: Enable the internal pull-up
 
+Note that when enabling the pull-up, the internal pad keeper gets disabled.
+Also, some pins doesn't have a pull up, in that case, setting the fsl,pull-up
+will only disable the internal pad keeper.
+
 Examples:
 
 pinctrl@80018000 {
diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt
index b77a97c9101..05ffecb5710 100644
--- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt
+++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-alc5632.txt
@@ -2,6 +2,11 @@ NVIDIA Tegra audio complex
 
 Required properties:
 - compatible : "nvidia,tegra-audio-alc5632"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
 - nvidia,model : The user-visible name of this sound complex.
 - nvidia,audio-routing : A list of the connections between audio components.
   Each entry is a pair of strings, the first being the connection's sink,
@@ -56,4 +61,7 @@ sound {
 
 	nvidia,i2s-controller = <&tegra_i2s1>;
 	nvidia,audio-codec = <&alc5632>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
 };
diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt
index 04b14cfb1f1..ef1fe735827 100644
--- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt
+++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-trimslice.txt
@@ -2,6 +2,11 @@ NVIDIA Tegra audio complex for TrimSlice
 
 Required properties:
 - compatible : "nvidia,tegra-audio-trimslice"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
 - nvidia,i2s-controller : The phandle of the Tegra I2S1 controller
 - nvidia,audio-codec : The phandle of the WM8903 audio codec
 
@@ -11,4 +16,6 @@ sound {
 	compatible = "nvidia,tegra-audio-trimslice";
 	nvidia,i2s-controller = <&tegra_i2s1>;
 	nvidia,audio-codec = <&codec>;
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
 };
diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt
index c4dd39ce616..d14510613a7 100644
--- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt
+++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8753.txt
@@ -2,6 +2,11 @@ NVIDIA Tegra audio complex
 
 Required properties:
 - compatible : "nvidia,tegra-audio-wm8753"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
 - nvidia,model : The user-visible name of this sound complex.
 - nvidia,audio-routing : A list of the connections between audio components.
   Each entry is a pair of strings, the first being the connection's sink,
@@ -50,5 +55,8 @@ sound {
 
 	nvidia,i2s-controller = <&i2s1>;
 	nvidia,audio-codec = <&wm8753>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
 };
 
diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt
index d5b0da8bf1d..3bf722deb72 100644
--- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt
+++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt
@@ -2,6 +2,11 @@ NVIDIA Tegra audio complex
 
 Required properties:
 - compatible : "nvidia,tegra-audio-wm8903"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
 - nvidia,model : The user-visible name of this sound complex.
 - nvidia,audio-routing : A list of the connections between audio components.
   Each entry is a pair of strings, the first being the connection's sink,
@@ -67,5 +72,8 @@ sound {
 	nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
 	nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
 	nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
 };
 
diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt
index be35d34e8b2..ad589b16363 100644
--- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt
+++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm9712.txt
@@ -2,6 +2,11 @@ NVIDIA Tegra audio complex
 
 Required properties:
 - compatible : "nvidia,tegra-audio-wm9712"
+- clocks : Must contain an entry for each entry in clock-names.
+- clock-names : Must include the following entries:
+  "pll_a" (The Tegra clock of that name),
+  "pll_a_out0" (The Tegra clock of that name),
+  "mclk" (The Tegra cdev1/extern1 clock, which feeds the CODEC's mclk)
 - nvidia,model : The user-visible name of this sound complex.
 - nvidia,audio-routing : A list of the connections between audio components.
   Each entry is a pair of strings, the first being the connection's sink,
@@ -48,4 +53,7 @@ sound {
 		"Mic", "MIC1";
 
 	nvidia,ac97-controller = <&ac97>;
+
+	clocks = <&tegra_car 112>, <&tegra_car 113>, <&tegra_car 93>;
+	clock-names = "pll_a", "pll_a_out0", "mclk";
 };
diff --git a/Documentation/devicetree/bindings/spi/mxs-spi.txt b/Documentation/devicetree/bindings/spi/mxs-spi.txt
index e2e13957c2a..3499b73293c 100644
--- a/Documentation/devicetree/bindings/spi/mxs-spi.txt
+++ b/Documentation/devicetree/bindings/spi/mxs-spi.txt
@@ -3,8 +3,11 @@
 Required properties:
 - compatible: Should be "fsl,<soc>-spi", where soc is "imx23" or "imx28"
 - reg: Offset and length of the register set for the device
-- interrupts: Should contain SSP interrupts (error irq first, dma irq second)
-- fsl,ssp-dma-channel: APBX DMA channel for the SSP
+- interrupts: Should contain SSP ERROR interrupt
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and SSP DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
 
 Optional properties:
 - clock-frequency : Input clock frequency to the SPI block in Hz.
@@ -17,6 +20,7 @@ ssp0: ssp@80010000 {
 	#size-cells = <0>;
 	compatible = "fsl,imx28-spi";
 	reg = <0x80010000 0x2000>;
-	interrupts = <96 82>;
-	fsl,ssp-dma-channel = <0>;
+	interrupts = <96>;
+	dmas = <&dma_apbh 0>;
+	dma-names = "rx-tx";
 };
diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt
new file mode 100644
index 00000000000..6d0ac8d0ad9
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt
@@ -0,0 +1,51 @@
+Davinci SPI controller device bindings
+
+Required properties:
+- #address-cells: number of cells required to define a chip select
+	address on the SPI bus. Should be set to 1.
+- #size-cells: should be zero.
+- compatible:
+	- "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family
+	- "ti,da830-spi" for SPI used similar to that on DA8xx SoC family
+- reg: Offset and length of SPI controller register space
+- num-cs: Number of chip selects
+- ti,davinci-spi-intr-line: interrupt line used to connect the SPI
+	IP to the interrupt controller within the SoC. Possible values
+	are 0 and 1. Manual says one of the two possible interrupt
+	lines can be tied to the interrupt controller. Set this
+	based on a specifc SoC configuration.
+- interrupts: interrupt number mapped to CPU.
+- clocks: spi clk phandle
+
+Example of a NOR flash slave device (n25q032) connected to DaVinci
+SPI controller device over the SPI bus.
+
+spi0:spi@20BF0000 {
+	#address-cells			= <1>;
+	#size-cells			= <0>;
+	compatible			= "ti,dm6446-spi";
+	reg				= <0x20BF0000 0x1000>;
+	num-cs				= <4>;
+	ti,davinci-spi-intr-line	= <0>;
+	interrupts			= <338>;
+	clocks				= <&clkspi>;
+
+	flash: n25q032@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "st,m25p32";
+		spi-max-frequency = <25000000>;
+		reg = <0>;
+
+		partition@0 {
+			label = "u-boot-spl";
+			reg = <0x0 0x80000>;
+			read-only;
+		};
+
+		partition@1 {
+			label = "test";
+			reg = <0x80000 0x380000>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt
index 273a8d5b330..2c00ec64628 100644
--- a/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt
+++ b/Documentation/devicetree/bindings/tty/serial/fsl-mxs-auart.txt
@@ -5,20 +5,18 @@ Required properties:
   imx23 and imx28.
 - reg : Address and length of the register set for the device
 - interrupts : Should contain the auart interrupt numbers
-
-Optional properties:
-- fsl,auart-dma-channel : The DMA channels, the first is for RX, the other
-		is for TX. If you add this property, it also means that you
-		will enable the DMA support for the auart.
-		Note: due to the hardware bug in imx23(see errata : 2836),
-		only the imx28 can enable the DMA support for the auart.
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and AUART DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: "rx" for RX channel, "tx" for TX channel.
 
 Example:
 auart0: serial@8006a000 {
 	compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 	reg = <0x8006a000 0x2000>;
-	interrupts = <112 70 71>;
-	fsl,auart-dma-channel = <8 9>;
+	interrupts = <112>;
+	dmas = <&dma_apbx 8>, <&dma_apbx 9>;
+	dma-names = "rx", "tx";
 };
 
 Note: Each auart port should have an alias correctly numbered in "aliases"
diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt
index f66fcddba46..b3abde73601 100644
--- a/Documentation/devicetree/bindings/usb/exynos-usb.txt
+++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt
@@ -10,6 +10,8 @@ Required properties:
  - reg: physical base address of the controller and length of memory mapped
    region.
  - interrupts: interrupt number to the cpu.
+ - clocks: from common clock binding: handle to usb clock.
+ - clock-names: from common clock binding: Shall be "usbhost".
 
 Optional properties:
  - samsung,vbus-gpio:  if present, specifies the GPIO that
@@ -22,6 +24,9 @@ Example:
 		reg = <0x12110000 0x100>;
 		interrupts = <0 71 0>;
 		samsung,vbus-gpio = <&gpx2 6 1 3 3>;
+
+		clocks = <&clock 285>;
+		clock-names = "usbhost";
 	};
 
 OHCI
@@ -31,10 +36,15 @@ Required properties:
  - reg: physical base address of the controller and length of memory mapped
    region.
  - interrupts: interrupt number to the cpu.
+ - clocks: from common clock binding: handle to usb clock.
+ - clock-names: from common clock binding: Shall be "usbhost".
 
 Example:
 	usb@12120000 {
 		compatible = "samsung,exynos4210-ohci";
 		reg = <0x12120000 0x100>;
 		interrupts = <0 71 0>;
+
+		clocks = <&clock 285>;
+		clock-names = "usbhost";
 	};
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index 662f0f1d231..d4769f343d6 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -18,6 +18,7 @@ OMAP MUSB GLUE
    represents PERIPHERAL.
  - power : Should be "50". This signifies the controller can supply upto
    100mA when operating in host mode.
+ - usb-phy : the phandle for the PHY device
 
 Optional properties:
  - ctrl-module : phandle of the control module this glue uses to write to
diff --git a/Documentation/devicetree/bindings/video/samsung-fimd.txt b/Documentation/devicetree/bindings/video/samsung-fimd.txt
new file mode 100644
index 00000000000..778838a0336
--- /dev/null
+++ b/Documentation/devicetree/bindings/video/samsung-fimd.txt
@@ -0,0 +1,65 @@
+Device-Tree bindings for Samsung SoC display controller (FIMD)
+
+FIMD (Fully Interactive Mobile Display) is the Display Controller for the
+Samsung series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be one of the following
+		"samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
+		"samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
+		"samsung,s5p6440-fimd"; /* for S5P64X0 SoCs */
+		"samsung,s5pc100-fimd"; /* for S5PC100 SoC  */
+		"samsung,s5pv210-fimd"; /* for S5PV210 SoC */
+		"samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
+		"samsung,exynos5250-fimd"; /* for Exynos5 SoCs */
+
+- reg: physical base address and length of the FIMD registers set.
+
+- interrupt-parent: should be the phandle of the fimd controller's
+		parent interrupt controller.
+
+- interrupts: should contain a list of all FIMD IP block interrupts in the
+		 order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
+		 format depends on the interrupt controller used.
+
+- interrupt-names: should contain the interrupt names: "fifo", "vsync",
+	"lcd_sys", in the same order as they were listed in the interrupts
+        property.
+
+- pinctrl-0: pin control group to be used for this controller.
+
+- pinctrl-names: must contain a "default" entry.
+
+- clocks: must include clock specifiers corresponding to entries in the
+         clock-names property.
+
+- clock-names: list of clock names sorted in the same order as the clocks
+               property. Must contain "sclk_fimd" and "fimd".
+
+Optional Properties:
+- samsung,power-domain: a phandle to FIMD power domain node.
+
+Example:
+
+SoC specific DT entry:
+
+	fimd@11c00000 {
+		compatible = "samsung,exynos4210-fimd";
+		interrupt-parent = <&combiner>;
+		reg = <0x11c00000 0x20000>;
+		interrupt-names = "fifo", "vsync", "lcd_sys";
+		interrupts = <11 0>, <11 1>, <11 2>;
+		clocks = <&clock 140>, <&clock 283>;
+		clock-names = "sclk_fimd", "fimd";
+		samsung,power-domain = <&pd_lcd0>;
+		status = "disabled";
+	};
+
+Board specific DT entry:
+
+	fimd@11c00000 {
+		pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+		pinctrl-names = "default";
+		status = "okay";
+	};