Merge tag 'omap-for-v3.9/gpmc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers

From Tony Lindgren:
OMAP GPMC (General Purpose Memory Controller) changes to add
device tree bindings.

* tag 'omap-for-v3.9/gpmc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: gpmc: Add device tree documentation for elm handle
  ARM: OMAP2+: gpmc: add DT bindings for OneNAND
  ARM: OMAP2+: gpmc-onenand: drop __init annotation
  mtd: omap-onenand: pass device_node in platform data
  ARM: OMAP2+: Prevent potential crash if GPMC probe fails
  ARM: OMAP2+: gpmc: Remove unneeded of_node_put()
  ARM: OMAP: gpmc: add DT bindings for GPMC timings and NAND
  ARM: OMAP: gpmc: enable hwecc for AM33xx SoCs
  ARM: OMAP: gpmc-nand: drop __init annotation
  mtd: omap-nand: pass device_node in platform data
  ARM: OMAP: gpmc: don't create devices from initcall on DT

Signed-off-by: Olof Johansson <olof@lixom.net>

3 files changed, 207 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/bus/ti-gpmc.txt b/Documentation/devicetree/bindings/bus/ti-gpmc.txt
new file mode 100644
index 00000000000..5ddb2e9efaa
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/ti-gpmc.txt
@@ -0,0 +1,84 @@
+Device tree bindings for OMAP general purpose memory controllers (GPMC)
+
+The actual devices are instantiated from the child nodes of a GPMC node.
+
+Required properties:
+
+ - compatible:		Should be set to one of the following:
+
+			ti,omap2420-gpmc (omap2420)
+			ti,omap2430-gpmc (omap2430)
+			ti,omap3430-gpmc (omap3430 & omap3630)
+			ti,omap4430-gpmc (omap4430 & omap4460 & omap543x)
+			ti,am3352-gpmc   (am335x devices)
+
+ - reg:			A resource specifier for the register space
+			(see the example below)
+ - ti,hwmods:		Should be set to "ti,gpmc" until the DT transition is
+			completed.
+ - #address-cells:	Must be set to 2 to allow memory address translation
+ - #size-cells:		Must be set to 1 to allow CS address passing
+ - gpmc,num-cs:		The maximum number of chip-select lines that controller
+			can support.
+ - gpmc,num-waitpins:	The maximum number of wait pins that controller can
+			support.
+ - ranges:		Must be set up to reflect the memory layout with four
+			integer values for each chip-select line in use:
+
+			   <cs-number> 0 <physical address of mapping> <size>
+
+			Currently, calculated values derived from the contents
+			of the per-CS register GPMC_CONFIG7 (as set up by the
+			bootloader) are used for the physical address decoding.
+			As this will change in the future, filling correct
+			values here is a requirement.
+
+Timing properties for child nodes. All are optional and default to 0.
+
+ - gpmc,sync-clk:	Minimum clock period for synchronous mode, in picoseconds
+
+ Chip-select signal timings corresponding to GPMC_CONFIG2:
+ - gpmc,cs-on:		Assertion time
+ - gpmc,cs-rd-off:	Read deassertion time
+ - gpmc,cs-wr-off:	Write deassertion time
+
+ ADV signal timings corresponding to GPMC_CONFIG3:
+ - gpmc,adv-on:		Assertion time
+ - gpmc,adv-rd-off:	Read deassertion time
+ - gpmc,adv-wr-off:	Write deassertion time
+
+ WE signals timings corresponding to GPMC_CONFIG4:
+ - gpmc,we-on:		Assertion time
+ - gpmc,we-off:		Deassertion time
+
+ OE signals timings corresponding to GPMC_CONFIG4:
+ - gpmc,oe-on:		Assertion time
+ - gpmc,oe-off:		Deassertion time
+
+ Access time and cycle time timings corresponding to GPMC_CONFIG5:
+ - gpmc,page-burst-access: Multiple access word delay
+ - gpmc,access:		Start-cycle to first data valid delay
+ - gpmc,rd-cycle:	Total read cycle time
+ - gpmc,wr-cycle:	Total write cycle time
+
+The following are only applicable to OMAP3+ and AM335x:
+ - gpmc,wr-access
+ - gpmc,wr-data-mux-bus
+
+
+Example for an AM33xx board:
+
+	gpmc: gpmc@50000000 {
+		compatible = "ti,am3352-gpmc";
+		ti,hwmods = "gpmc";
+		reg = <0x50000000 0x2000>;
+		interrupts = <100>;
+
+		gpmc,num-cs = <8>;
+		gpmc,num-waitpins = <2>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */
+
+		/* child nodes go here */
+	};
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-nand.txt b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
new file mode 100644
index 00000000000..e7f8d7ed47e
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/gpmc-nand.txt
@@ -0,0 +1,80 @@
+Device tree bindings for GPMC connected NANDs
+
+GPMC connected NAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "nand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+For NAND specific properties such as ECC modes or bus width, please refer to
+Documentation/devicetree/bindings/mtd/nand.txt
+
+
+Required properties:
+
+ - reg:		The CS line the peripheral is connected to
+
+Optional properties:
+
+ - nand-bus-width: 		Set this numeric value to 16 if the hardware
+				is wired that way. If not specified, a bus
+				width of 8 is assumed.
+
+ - ti,nand-ecc-opt:		A string setting the ECC layout to use. One of:
+
+		"sw"		Software method (default)
+		"hw"		Hardware method
+		"hw-romcode"	gpmc hamming mode method & romcode layout
+		"bch4"		4-bit BCH ecc code
+		"bch8"		8-bit BCH ecc code
+
+ - elm_id:	Specifies elm device node. This is required to support BCH
+ 		error correction using ELM module.
+
+For inline partiton table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an AM33xx board:
+
+	gpmc: gpmc@50000000 {
+		compatible = "ti,am3352-gpmc";
+		ti,hwmods = "gpmc";
+		reg = <0x50000000 0x1000000>;
+		interrupts = <100>;
+		gpmc,num-cs = <8>;
+		gpmc,num-waitpins = <2>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x2000>;	/* CS0: NAND */
+		elm_id = <&elm>;
+
+		nand@0,0 {
+			reg = <0 0 0>; /* CS0, offset 0 */
+			nand-bus-width = <16>;
+			ti,nand-ecc-opt = "bch8";
+
+			gpmc,sync-clk = <0>;
+			gpmc,cs-on = <0>;
+			gpmc,cs-rd-off = <44>;
+			gpmc,cs-wr-off = <44>;
+			gpmc,adv-on = <6>;
+			gpmc,adv-rd-off = <34>;
+			gpmc,adv-wr-off = <44>;
+			gpmc,we-off = <40>;
+			gpmc,oe-off = <54>;
+			gpmc,access = <64>;
+			gpmc,rd-cycle = <82>;
+			gpmc,wr-cycle = <82>;
+			gpmc,wr-access = <40>;
+			gpmc,wr-data-mux-bus = <0>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/* partitions go here */
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
new file mode 100644
index 00000000000..deec9da224a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/gpmc-onenand.txt
@@ -0,0 +1,43 @@
+Device tree bindings for GPMC connected OneNANDs
+
+GPMC connected OneNAND (found on OMAP boards) are represented as child nodes of
+the GPMC controller with a name of "onenand".
+
+All timing relevant properties as well as generic gpmc child properties are
+explained in a separate documents - please refer to
+Documentation/devicetree/bindings/bus/ti-gpmc.txt
+
+Required properties:
+
+ - reg:			The CS line the peripheral is connected to
+
+Optional properties:
+
+ - dma-channel:		DMA Channel index
+
+For inline partiton table parsing (optional):
+
+ - #address-cells: should be set to 1
+ - #size-cells: should be set to 1
+
+Example for an OMAP3430 board:
+
+	gpmc: gpmc@6e000000 {
+		compatible = "ti,omap3430-gpmc";
+		ti,hwmods = "gpmc";
+		reg = <0x6e000000 0x1000000>;
+		interrupts = <20>;
+		gpmc,num-cs = <8>;
+		gpmc,num-waitpins = <4>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+
+		onenand@0 {
+			reg = <0 0 0>; /* CS0, offset 0 */
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/* partitions go here */
+		};
+	};