Merge branch 'power-supply-scope' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen

46 files changed, 1367 insertions, 64 deletions

diff --git a/Documentation/devicetree/bindings/arm/calxeda.txt b/Documentation/devicetree/bindings/arm/calxeda.txt
new file mode 100644
index 00000000000..4755caaccba
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/calxeda.txt
@@ -0,0 +1,8 @@
+Calxeda Highbank Platforms Device Tree Bindings
+-----------------------------------------------
+
+Boards with Calxeda Cortex-A9 based Highbank SOC shall have the following
+properties.
+
+Required root node properties:
+    - compatible = "calxeda,highbank";
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
new file mode 100644
index 00000000000..c9848ad0e2e
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -0,0 +1,26 @@
+Freescale i.MX Platforms Device Tree Bindings
+-----------------------------------------------
+
+i.MX51 Babbage Board
+Required root node properties:
+    - compatible = "fsl,imx51-babbage", "fsl,imx51";
+
+i.MX53 Automotive Reference Design Board
+Required root node properties:
+    - compatible = "fsl,imx53-ard", "fsl,imx53";
+
+i.MX53 Evaluation Kit
+Required root node properties:
+    - compatible = "fsl,imx53-evk", "fsl,imx53";
+
+i.MX53 Quick Start Board
+Required root node properties:
+    - compatible = "fsl,imx53-qsb", "fsl,imx53";
+
+i.MX53 Smart Mobile Reference Design Board
+Required root node properties:
+    - compatible = "fsl,imx53-smd", "fsl,imx53";
+
+i.MX6 Quad SABRE Automotive Board
+Required root node properties:
+    - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
diff --git a/Documentation/devicetree/bindings/arm/gic.txt b/Documentation/devicetree/bindings/arm/gic.txt
new file mode 100644
index 00000000000..52916b4aa1f
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/gic.txt
@@ -0,0 +1,55 @@
+* ARM Generic Interrupt Controller
+
+ARM SMP cores are often associated with a GIC, providing per processor
+interrupts (PPI), shared processor interrupts (SPI) and software
+generated interrupts (SGI).
+
+Primary GIC is attached directly to the CPU and typically has PPIs and SGIs.
+Secondary GICs are cascaded into the upward interrupt controller and do not
+have PPIs or SGIs.
+
+Main node required properties:
+
+- compatible : should be one of:
+	"arm,cortex-a9-gic"
+	"arm,arm11mp-gic"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source.  The type shall be a <u32> and the value shall be 3.
+
+  The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI
+  interrupts.
+
+  The 2nd cell contains the interrupt number for the interrupt type.
+  SPI interrupts are in the range [0-987].  PPI interrupts are in the
+  range [0-15].
+
+  The 3rd cell is the flags, encoded as follows:
+	bits[3:0] trigger type and level flags.
+		1 = low-to-high edge triggered
+		2 = high-to-low edge triggered
+		4 = active high level-sensitive
+		8 = active low level-sensitive
+	bits[15:8] PPI interrupt cpu mask.  Each bit corresponds to each of
+	the 8 possible cpus attached to the GIC.  A bit set to '1' indicated
+	the interrupt is wired to that CPU.  Only valid for PPI interrupts.
+
+- reg : Specifies base physical address(s) and size of the GIC registers. The
+  first region is the GIC distributor register base and size. The 2nd region is
+  the GIC cpu interface register base and size.
+
+Optional
+- interrupts	: Interrupt source of the parent interrupt controller. Only
+  present on secondary GICs.
+
+Example:
+
+	intc: interrupt-controller@fff11000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		interrupt-controller;
+		reg = <0xfff11000 0x1000>,
+		      <0xfff10100 0x100>;
+	};
+
diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt
new file mode 100644
index 00000000000..7ca52161e7a
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/l2cc.txt
@@ -0,0 +1,44 @@
+* ARM L2 Cache Controller
+
+ARM cores often have a separate level 2 cache controller. There are various
+implementations of the L2 cache controller with compatible programming models.
+The ARM L2 cache representation in the device tree should be done as follows:
+
+Required properties:
+
+- compatible : should be one of:
+	"arm,pl310-cache"
+	"arm,l220-cache"
+	"arm,l210-cache"
+- cache-unified : Specifies the cache is a unified cache.
+- cache-level : Should be set to 2 for a level 2 cache.
+- reg : Physical base address and size of cache controller's memory mapped
+  registers.
+
+Optional properties:
+
+- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of
+  read, write and setup latencies. Minimum valid values are 1. Controllers
+  without setup latency control should use a value of 0.
+- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of
+  read, write and setup latencies. Controllers without setup latency control
+  should use 0. Controllers without separate read and write Tag RAM latency
+  values should only use the first cell.
+- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell.
+- arm,filter-ranges : <start length> Starting address and length of window to
+  filter. Addresses in the filter window are directed to the M1 port. Other
+  addresses will go to the M0 port.
+- interrupts : 1 combined interrupt.
+
+Example:
+
+L2: cache-controller {
+        compatible = "arm,pl310-cache";
+        reg = <0xfff12000 0x1000>;
+        arm,data-latency = <1 1 1>;
+        arm,tag-latency = <2 2 2>;
+        arm,filter-latency = <0x80000000 0x8000000>;
+        cache-unified;
+        cache-level = <2>;
+	interrupts = <45>;
+};
diff --git a/Documentation/devicetree/bindings/arm/omap/dsp.txt b/Documentation/devicetree/bindings/arm/omap/dsp.txt
new file mode 100644
index 00000000000..d3830a32ce0
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/dsp.txt
@@ -0,0 +1,14 @@
+* TI - DSP (Digital Signal Processor)
+
+TI DSP included in OMAP SoC
+
+Required properties:
+- compatible : Should be "ti,omap3-c64" for OMAP3 & 4
+- ti,hwmods: "dsp"
+
+Examples:
+
+dsp {
+    compatible = "ti,omap3-c64";
+    ti,hwmods = "dsp";
+};
diff --git a/Documentation/devicetree/bindings/arm/omap/iva.txt b/Documentation/devicetree/bindings/arm/omap/iva.txt
new file mode 100644
index 00000000000..6d629517135
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/iva.txt
@@ -0,0 +1,19 @@
+* TI - IVA (Imaging and Video Accelerator) subsystem
+
+The IVA contain various audio, video or imaging HW accelerator
+depending of the version.
+
+Required properties:
+- compatible : Should be:
+  - "ti,ivahd" for OMAP4
+  - "ti,iva2.2" for OMAP3
+  - "ti,iva2.1" for OMAP2430
+  - "ti,iva1" for OMAP2420
+- ti,hwmods: "iva"
+
+Examples:
+
+iva {
+    compatible = "ti,ivahd", "ti,iva";
+    ti,hwmods = "iva";
+};
diff --git a/Documentation/devicetree/bindings/arm/omap/l3-noc.txt b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
new file mode 100644
index 00000000000..6888a5efc86
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/l3-noc.txt
@@ -0,0 +1,19 @@
+* TI - L3 Network On Chip (NoC)
+
+This version is an implementation of the generic NoC IP
+provided by Arteris.
+
+Required properties:
+- compatible : Should be "ti,omap3-l3-smx" for OMAP3 family
+               Should be "ti,omap4-l3-noc" for OMAP4 family
+- ti,hwmods: "l3_main_1", ... One hwmod for each noc domain.
+
+Examples:
+
+ocp {
+	compatible = "ti,omap4-l3-noc", "simple-bus";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+	ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
+};
diff --git a/Documentation/devicetree/bindings/arm/omap/mpu.txt b/Documentation/devicetree/bindings/arm/omap/mpu.txt
new file mode 100644
index 00000000000..1a5a42ce21b
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/mpu.txt
@@ -0,0 +1,27 @@
+* TI - MPU (Main Processor Unit) subsystem
+
+The MPU subsystem contain one or several ARM cores
+depending of the version.
+The MPU contain CPUs, GIC, L2 cache and a local PRCM.
+
+Required properties:
+- compatible : Should be "ti,omap3-mpu" for OMAP3
+               Should be "ti,omap4-mpu" for OMAP4
+- ti,hwmods: "mpu"
+
+Examples:
+
+- For an OMAP4 SMP system:
+
+mpu {
+    compatible = "ti,omap4-mpu";
+    ti,hwmods = "mpu";
+};
+
+
+- For an OMAP3 monocore system:
+
+mpu {
+    compatible = "ti,omap3-mpu";
+    ti,hwmods = "mpu";
+};
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
new file mode 100644
index 00000000000..dbdab40ed3a
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -0,0 +1,43 @@
+* Texas Instruments OMAP
+
+OMAP is currently using a static file per SoC family to describe the
+IPs present in the SoC.
+On top of that an omap_device is created to extend the platform_device
+capabilities and to allow binding with one or several hwmods.
+The hwmods will contain all the information to build the device:
+adresse range, irq lines, dma lines, interconnect, PRCM register,
+clock domain, input clocks.
+For the moment just point to the existing hwmod, the next step will be
+to move data from hwmod to device-tree representation.
+
+
+Required properties:
+- compatible: Every devices present in OMAP SoC should be in the
+  form: "ti,XXX"
+- ti,hwmods: list of hwmod names (ascii strings), that comes from the OMAP
+  HW documentation, attached to a device. Must contain at least
+  one hwmod.
+
+Optional properties:
+- ti,no_idle_on_suspend: When present, it prevents the PM to idle the module
+  during suspend.
+
+
+Example:
+
+spinlock@1 {
+    compatible = "ti,omap4-spinlock";
+    ti,hwmods = "spinlock";
+};
+
+
+Boards:
+
+- OMAP3 BeagleBoard : Low cost community board
+  compatible = "ti,omap3-beagle", "ti,omap3"
+
+- OMAP4 SDP : Software Developement Board
+  compatible = "ti,omap4-sdp", "ti,omap4430"
+
+- OMAP4 PandaBoard : Low cost community board
+  compatible = "ti,omap4-panda", "ti,omap4430"
diff --git a/Documentation/devicetree/bindings/arm/picoxcell.txt b/Documentation/devicetree/bindings/arm/picoxcell.txt
new file mode 100644
index 00000000000..e75c0ef51e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/picoxcell.txt
@@ -0,0 +1,24 @@
+Picochip picoXcell device tree bindings.
+========================================
+
+Required root node properties:
+    - compatible:
+	- "picochip,pc7302-pc3x3" : PC7302 development board with PC3X3 device.
+	- "picochip,pc7302-pc3x2" : PC7302 development board with PC3X2 device.
+	- "picochip,pc3x3" : picoXcell PC3X3 device based board.
+	- "picochip,pc3x2" : picoXcell PC3X2 device based board.
+
+Timers required properties:
+    - compatible = "picochip,pc3x2-timer"
+    - interrupts : The single IRQ line for the timer.
+    - clock-freq : The frequency in HZ of the timer.
+    - reg : The register bank for the timer.
+
+Note: two timers are required - one for the scheduler clock and one for the
+event tick/NOHZ.
+
+VIC required properties:
+    - compatible = "arm,pl192-vic".
+    - interrupt-controller.
+    - reg : The register bank for the device.
+    - #interrupt-cells : Must be 1.
diff --git a/Documentation/devicetree/bindings/arm/primecell.txt b/Documentation/devicetree/bindings/arm/primecell.txt
index 1d5d7a870ec..951ca46789d 100644
--- a/Documentation/devicetree/bindings/arm/primecell.txt
+++ b/Documentation/devicetree/bindings/arm/primecell.txt
@@ -6,7 +6,9 @@ driver matching.
 
 Required properties:
 
-- compatible : should be a specific value for peripheral and "arm,primecell"
+- compatible : should be a specific name for the peripheral and
+               "arm,primecell".  The specific name will match the ARM
+               engineering name for the logic block in the form: "arm,pl???"
 
 Optional properties:
 
diff --git a/Documentation/devicetree/bindings/ata/calxeda-sata.txt b/Documentation/devicetree/bindings/ata/calxeda-sata.txt
new file mode 100644
index 00000000000..79caa5651f5
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/calxeda-sata.txt
@@ -0,0 +1,17 @@
+* Calxeda SATA Controller
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "calxeda,hb-ahci"
+- interrupts        : <interrupt mapping for SATA IRQ>
+- reg               : <registers mapping>
+
+Example:
+        sata@ffe08000 {
+		compatible = "calxeda,hb-ahci";
+                reg = <0xffe08000 0x1000>;
+                interrupts = <115>;
+        };
+
diff --git a/Documentation/devicetree/bindings/crypto/picochip-spacc.txt b/Documentation/devicetree/bindings/crypto/picochip-spacc.txt
new file mode 100644
index 00000000000..d8609ece1f4
--- /dev/null
+++ b/Documentation/devicetree/bindings/crypto/picochip-spacc.txt
@@ -0,0 +1,23 @@
+Picochip picoXcell SPAcc (Security Protocol Accelerator) bindings
+
+Picochip picoXcell devices contain crypto offload engines that may be used for
+IPSEC and femtocell layer 2 ciphering.
+
+Required properties:
+  - compatible : "picochip,spacc-ipsec" for the IPSEC offload engine
+    "picochip,spacc-l2" for the femtocell layer 2 ciphering engine.
+  - reg : Offset and length of the register set for this device
+  - interrupt-parent : The interrupt controller that controls the SPAcc
+    interrupt.
+  - interrupts : The interrupt line from the SPAcc.
+  - ref-clock : The input clock that drives the SPAcc.
+
+Example SPAcc node:
+
+spacc@10000 {
+	compatible = "picochip,spacc-ipsec";
+	reg = <0x100000 0x10000>;
+	interrupt-parent = <&vic0>;
+	interrupts = <24>;
+	ref-clock = <&ipsec_clk>, "ref";
+};
diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt
index 064db928c3c..141087cf310 100644
--- a/Documentation/devicetree/bindings/gpio/led.txt
+++ b/Documentation/devicetree/bindings/gpio/led.txt
@@ -8,7 +8,7 @@ node's name represents the name of the corresponding LED.
 
 LED sub-node properties:
 - gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
-  for devices" in Documentation/powerpc/booting-without-of.txt.  Active
+  for devices" in Documentation/devicetree/booting-without-of.txt.  Active
   low LEDs should be indicated using flags in the GPIO specifier.
 - label :  (optional) The label for this LED.  If omitted, the label is
   taken from the node name (excluding the unit address).
diff --git a/Documentation/devicetree/bindings/gpio/pl061-gpio.txt b/Documentation/devicetree/bindings/gpio/pl061-gpio.txt
new file mode 100644
index 00000000000..a2c416bcbcc
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/pl061-gpio.txt
@@ -0,0 +1,10 @@
+ARM PL061 GPIO controller
+
+Required properties:
+- compatible : "arm,pl061", "arm,primecell"
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters:
+  - bit 0 specifies polarity (0 for normal, 1 for inverted)
+- gpio-controller : Marks the device node as a GPIO controller.
+- interrupts : Interrupt mapping for GPIO IRQ.
+
diff --git a/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt b/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt
new file mode 100644
index 00000000000..f3cf43b66f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/fsl-imx-i2c.txt
@@ -0,0 +1,25 @@
+* Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX
+
+Required properties:
+- compatible : Should be "fsl,<chip>-i2c"
+- reg : Should contain I2C/HS-I2C registers location and length
+- interrupts : Should contain I2C/HS-I2C interrupt
+
+Optional properties:
+- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
+  The absence of the propoerty indicates the default frequency 100 kHz.
+
+Examples:
+
+i2c@83fc4000 { /* I2C2 on i.MX51 */
+	compatible = "fsl,imx51-i2c", "fsl,imx1-i2c";
+	reg = <0x83fc4000 0x4000>;
+	interrupts = <63>;
+};
+
+i2c@70038000 { /* HS-I2C on i.MX51 */
+	compatible = "fsl,imx51-i2c", "fsl,imx1-i2c";
+	reg = <0x70038000 0x4000>;
+	interrupts = <64>;
+	clock-frequency = <400000>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
new file mode 100644
index 00000000000..38832c71291
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
@@ -0,0 +1,39 @@
+* Samsung's I2C controller
+
+The Samsung's I2C controller is used to interface with I2C devices.
+
+Required properties:
+  - compatible: value should be either of the following.
+      (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
+      (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
+  - reg: physical base address of the controller and length of memory mapped
+    region.
+  - interrupts: interrupt number to the cpu.
+  - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
+  - gpios: The order of the gpios should be the following: <SDA, SCL>.
+    The gpio specifier depends on the gpio controller.
+
+Optional properties:
+  - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
+    specified, default value is 0.
+  - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
+    specified, the default value in Hz is 100000.
+
+Example:
+
+	i2c@13870000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13870000 0x100>;
+		interrupts = <345>;
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <100000>;
+		gpios = <&gpd1 2 0 /* SDA */
+			 &gpd1 3 0 /* SCL */>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wm8994@1a {
+			compatible = "wlf,wm8994";
+			reg = <0x1a>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
new file mode 100644
index 00000000000..7e51154679a
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/nvidia-sdhci.txt
@@ -0,0 +1,27 @@
+* NVIDIA Tegra Secure Digital Host Controller
+
+This controller on Tegra family SoCs provides an interface for MMC, SD,
+and SDIO types of memory cards.
+
+Required properties:
+- compatible : Should be "nvidia,<chip>-sdhci"
+- reg : Should contain SD/MMC registers location and length
+- interrupts : Should contain SD/MMC interrupt
+
+Optional properties:
+- cd-gpios : Specify GPIOs for card detection
+- wp-gpios : Specify GPIOs for write protection
+- power-gpios : Specify GPIOs for power control
+- support-8bit : Boolean, indicates if 8-bit mode should be used.
+
+Example:
+
+sdhci@c8000200 {
+	compatible = "nvidia,tegra20-sdhci";
+	reg = <0xc8000200 0x200>;
+	interrupts = <47>;
+	cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+	wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+	power-gpios = <&gpio 155 0>; /* gpio PT3 */
+	support-8bit;
+};
diff --git a/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt
new file mode 100644
index 00000000000..ef66ddd01da
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/atmel-dataflash.txt
@@ -0,0 +1,14 @@
+* Atmel Data Flash
+
+Required properties:
+- compatible : "atmel,<model>", "atmel,<series>", "atmel,dataflash".
+
+Example:
+
+flash@1 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "atmel,at45db321d", "atmel,at45", "atmel,dataflash";
+	spi-max-frequency = <25000000>;
+	reg = <1>;
+};
diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
index 1a729f08986..1ad80d5865a 100644
--- a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
+++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt
@@ -1,61 +1,24 @@
-CAN Device Tree Bindings
-------------------------
-2011 Freescale Semiconductor, Inc.
+Flexcan CAN contoller on Freescale's ARM and PowerPC system-on-a-chip (SOC).
 
-fsl,flexcan-v1.0 nodes
------------------------
-In addition to the required compatible-, reg- and interrupt-properties, you can
-also specify which clock source shall be used for the controller.
+Required properties:
 
-CPI Clock- Can Protocol Interface Clock
-	This CLK_SRC bit of CTRL(control register) selects the clock source to
-	the CAN Protocol Interface(CPI) to be either the peripheral clock
-	(driven by the PLL) or the crystal oscillator clock. The selected clock
-	is the one fed to the prescaler to generate the Serial Clock (Sclock).
-	The PRESDIV field of CTRL(control register) controls a prescaler that
-	generates the Serial Clock (Sclock), whose period defines the
-	time quantum used to compose the CAN waveform.
+- compatible : Should be "fsl,<processor>-flexcan"
 
-Can Engine Clock Source
-	There are two sources for CAN clock
-	- Platform Clock  It represents the bus clock
-	- Oscillator Clock
+  An implementation should also claim any of the following compatibles
+  that it is fully backwards compatible with:
 
-	Peripheral Clock (PLL)
-	--------------
-		     |
-		    ---------		      -------------
-		    |       |CPI Clock	      | Prescaler |       Sclock
-		    |       |---------------->| (1.. 256) |------------>
-		    ---------		      -------------
-                     |  |
-	--------------  ---------------------CLK_SRC
-	Oscillator Clock
+  - fsl,p1010-flexcan
 </