dt: Move device tree documentation out of powerpc directory

The device tree is used by more than just PowerPC.  Make the documentation
directory available to all.

v2: reorganized files while moving to create arch and driver specific
    directories.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>

60 files changed, 5554 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/ata/fsl-sata.txt b/Documentation/devicetree/bindings/ata/fsl-sata.txt
new file mode 100644
index 00000000000..b46bcf46c3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/ata/fsl-sata.txt
@@ -0,0 +1,29 @@
+* Freescale 8xxx/3.0 Gb/s SATA nodes
+
+SATA nodes are defined to describe on-chip Serial ATA controllers.
+Each SATA port should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains 2 entries, first is
+		 "fsl,CHIP-sata", where CHIP is the processor
+		 (mpc8315, mpc8379, etc.) and the second is
+		 "fsl,pq-sata"
+- interrupts        : <interrupt mapping for SATA IRQ>
+- cell-index        : controller index.
+                          1 for controller @ 0x18000
+                          2 for controller @ 0x19000
+                          3 for controller @ 0x1a000
+                          4 for controller @ 0x1b000
+
+Optional properties:
+- interrupt-parent  : optional, if needed for interrupt mapping
+- reg               : <registers mapping>
+
+Example:
+	sata@18000 {
+		compatible = "fsl,mpc8379-sata", "fsl,pq-sata";
+		reg = <0x18000 0x1000>;
+		cell-index = <1>;
+		interrupts = <2c 8>;
+		interrupt-parent = < &ipic >;
+	};
diff --git a/Documentation/devicetree/bindings/eeprom.txt b/Documentation/devicetree/bindings/eeprom.txt
new file mode 100644
index 00000000000..4342c10de1b
--- /dev/null
+++ b/Documentation/devicetree/bindings/eeprom.txt
@@ -0,0 +1,28 @@
+EEPROMs (I2C)
+
+Required properties:
+
+  - compatible : should be "<manufacturer>,<type>"
+		 If there is no specific driver for <manufacturer>, a generic
+		 driver based on <type> is selected. Possible types are:
+		 24c00, 24c01, 24c02, 24c04, 24c08, 24c16, 24c32, 24c64,
+		 24c128, 24c256, 24c512, 24c1024, spd
+
+  - reg : the I2C address of the EEPROM
+
+Optional properties:
+
+  - pagesize : the length of the pagesize for writing. Please consult the
+               manual of your device, that value varies a lot. A wrong value
+	       may result in data loss! If not specified, a safety value of
+	       '1' is used which will be very slow.
+
+  - read-only: this parameterless property disables writes to the eeprom
+
+Example:
+
+eeprom@52 {
+	compatible = "atmel,24c32";
+	reg = <0x52>;
+	pagesize = <32>;
+};
diff --git a/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt
new file mode 100644
index 00000000000..b0019eb5330
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/8xxx_gpio.txt
@@ -0,0 +1,60 @@
+GPIO controllers on MPC8xxx SoCs
+
+This is for the non-QE/CPM/GUTs GPIO controllers as found on
+8349, 8572, 8610 and compatible.
+
+Every GPIO controller node must have #gpio-cells property defined,
+this information will be used to translate gpio-specifiers.
+
+Required properties:
+- compatible : "fsl,<CHIP>-gpio" followed by "fsl,mpc8349-gpio" for
+  83xx, "fsl,mpc8572-gpio" for 85xx and "fsl,mpc8610-gpio" for 86xx.
+- #gpio-cells : Should be two. The first cell is the pin number and the
+  second cell is used to specify optional parameters (currently unused).
+ - interrupts : Interrupt mapping for GPIO IRQ.
+ - interrupt-parent : Phandle for the interrupt controller that
+   services interrupts for this device.
+- gpio-controller : Marks the port as GPIO controller.
+
+Example of gpio-controller nodes for a MPC8347 SoC:
+
+	gpio1: gpio-controller@c00 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio";
+		reg = <0xc00 0x100>;
+		interrupts = <74 0x8>;
+		interrupt-parent = <&ipic>;
+		gpio-controller;
+	};
+
+	gpio2: gpio-controller@d00 {
+		#gpio-cells = <2>;
+		compatible = "fsl,mpc8347-gpio", "fsl,mpc8349-gpio";
+		reg = <0xd00 0x100>;
+		interrupts = <75 0x8>;
+		interrupt-parent = <&ipic>;
+		gpio-controller;
+	};
+
+See booting-without-of.txt for details of how to specify GPIO
+information for devices.
+
+To use GPIO pins as interrupt sources for peripherals, specify the
+GPIO controller as the interrupt parent and define GPIO number +
+trigger mode using the interrupts property, which is defined like
+this:
+
+interrupts = <number trigger>, where:
+ - number: GPIO pin (0..31)
+ - trigger: trigger mode:
+	2 = trigger on falling edge
+	3 = trigger on both edges
+
+Example of device using this is:
+
+	funkyfpga@0 {
+		compatible = "funky-fpga";
+		...
+		interrupts = <4 3>;
+		interrupt-parent = <&gpio1>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt
new file mode 100644
index 00000000000..edaa84d288a
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio.txt
@@ -0,0 +1,50 @@
+Specifying GPIO information for devices
+============================================
+
+1) gpios property
+-----------------
+
+Nodes that makes use of GPIOs should define them using `gpios' property,
+format of which is: <&gpio-controller1-phandle gpio1-specifier
+		     &gpio-controller2-phandle gpio2-specifier
+		     0 /* holes are permitted, means no GPIO 3 */
+		     &gpio-controller4-phandle gpio4-specifier
+		     ...>;
+
+Note that gpio-specifier length is controller dependent.
+
+gpio-specifier may encode: bank, pin position inside the bank,
+whether pin is open-drain and whether pin is logically inverted.
+
+Example of the node using GPIOs:
+
+	node {
+		gpios = <&qe_pio_e 18 0>;
+	};
+
+In this example gpio-specifier is "18 0" and encodes GPIO pin number,
+and empty GPIO flags as accepted by the "qe_pio_e" gpio-controller.
+
+2) gpio-controller nodes
+------------------------
+
+Every GPIO controller node must have #gpio-cells property defined,
+this information will be used to translate gpio-specifiers.
+
+Example of two SOC GPIO banks defined as gpio-controller nodes:
+
+	qe_pio_a: gpio-controller@1400 {
+		#gpio-cells = <2>;
+		compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank";
+		reg = <0x1400 0x18>;
+		gpio-controller;
+	};
+
+	qe_pio_e: gpio-controller@1460 {
+		#gpio-cells = <2>;
+		compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank";
+		reg = <0x1460 0x18>;
+		gpio-controller;
+	};
+
+
diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt
new file mode 100644
index 00000000000..064db928c3c
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/led.txt
@@ -0,0 +1,58 @@
+LEDs connected to GPIO lines
+
+Required properties:
+- compatible : should be "gpio-leds".
+
+Each LED is represented as a sub-node of the gpio-leds device.  Each
+node's name represents the name of the corresponding LED.
+
+LED sub-node properties:
+- gpios :  Should specify the LED's GPIO, see "Specifying GPIO information
+  for devices" in Documentation/powerpc/booting-without-of.txt.  Active
+  low LEDs should be indicated using flags in the GPIO specifier.
+- label :  (optional) The label for this LED.  If omitted, the label is
+  taken from the node name (excluding the unit address).
+- linux,default-trigger :  (optional) This parameter, if present, is a
+  string defining the trigger assigned to the LED.  Current triggers are:
+    "backlight" - LED will act as a back-light, controlled by the framebuffer
+		  system
+    "default-on" - LED will turn on, but see "default-state" below
+    "heartbeat" - LED "double" flashes at a load average based rate
+    "ide-disk" - LED indicates disk activity
+    "timer" - LED flashes at a fixed, configurable rate
+- default-state:  (optional) The initial state of the LED.  Valid
+  values are "on", "off", and "keep".  If the LED is already on or off
+  and the default-state property is set the to same value, then no
+  glitch should be produced where the LED momentarily turns off (or
+  on).  The "keep" setting will keep the LED at whatever its current
+  state is, without producing a glitch.  The default is off if this
+  property is not present.
+
+Examples:
+
+leds {
+	compatible = "gpio-leds";
+	hdd {
+		label = "IDE Activity";
+		gpios = <&mcu_pio 0 1>; /* Active low */
+		linux,default-trigger = "ide-disk";
+	};
+
+	fault {
+		gpios = <&mcu_pio 1 0>;
+		/* Keep LED on if BIOS detected hardware fault */
+		default-state = "keep";
+	};
+};
+
+run-control {
+	compatible = "gpio-leds";
+	red {
+		gpios = <&mpc8572 6 0>;
+		default-state = "off";
+	};
+	green {
+		gpios = <&mpc8572 7 0>;
+		default-state = "on";
+	};
+}
diff --git a/Documentation/devicetree/bindings/i2c/fsl-i2c.txt b/Documentation/devicetree/bindings/i2c/fsl-i2c.txt
new file mode 100644
index 00000000000..1eacd6b20ed
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/fsl-i2c.txt
@@ -0,0 +1,64 @@
+* I2C
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a
+   compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121,
+   mpc5200 or mpc5200b. For the mpc5121, an additional node
+   "fsl,mpc5121-i2c-ctrl" is required as shown in the example below.
+
+Recommended properties :
+
+ - interrupts : <a b> where a is the interrupt number and b is a
+   field that represents an encoding of the sense and level
+   information for the interrupt.  This should be encoded based on
+   the information in section 2) depending on the type of interrupt
+   controller you have.
+ - interrupt-parent : the phandle for the interrupt controller that
+   services interrupts for this device.
+ - fsl,preserve-clocking : boolean; if defined, the clock settings
+   from the bootloader are preserved (not touched).
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+ - fsl,timeout : I2C bus timeout in microseconds.
+
+Examples :
+
+	/* MPC5121 based board */
+	i2c@1740 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc5121-i2c", "fsl-i2c";
+		reg = <0x1740 0x20>;
+		interrupts = <11 0x8>;
+		interrupt-parent = <&ipic>;
+		clock-frequency = <100000>;
+	};
+
+	i2ccontrol@1760 {
+		compatible = "fsl,mpc5121-i2c-ctrl";
+		reg = <0x1760 0x8>;
+	};
+
+	/* MPC5200B based board */
+	i2c@3d00 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+		reg = <0x3d00 0x40>;
+		interrupts = <2 15 0>;
+		interrupt-parent = <&mpc5200_pic>;
+		fsl,preserve-clocking;
+	};
+
+	/* MPC8544 base board */
+	i2c@3100 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc8544-i2c", "fsl-i2c";
+		reg = <0x3100 0x100>;
+		interrupts = <43 2>;
+		interrupt-parent = <&mpic>;
+		clock-frequency = <400000>;
+		fsl,timeout = <10000>;
+	};
diff --git a/Documentation/devicetree/bindings/marvell.txt b/Documentation/devicetree/bindings/marvell.txt
new file mode 100644
index 00000000000..f1533d91953
--- /dev/null
+++ b/Documentation/devicetree/bindings/marvell.txt
@@ -0,0 +1,521 @@
+Marvell Discovery mv64[345]6x System Controller chips
+===========================================================
+
+The Marvell mv64[345]60 series of system controller chips contain
+many of the peripherals needed to implement a complete computer
+system.  In this section, we define device tree nodes to describe
+the system controller chip itself and each of the peripherals
+which it contains.  Compatible string values for each node are
+prefixed with the string "marvell,", for Marvell Technology Group Ltd.
+
+1) The /system-controller node
+
+  This node is used to represent the system-controller and must be
+  present when the system uses a system controller chip. The top-level
+  system-controller node contains information that is global to all
+  devices within the system controller chip. The node name begins
+  with "system-controller" followed by the unit address, which is
+  the base address of the memory-mapped register set for the system
+  controller chip.
+
+  Required properties:
+
+    - ranges : Describes the translation of system controller addresses
+      for memory mapped registers.
+    - clock-frequency: Contains the main clock frequency for the system
+      controller chip.
+    - reg : This property defines the address and size of the
+      memory-mapped registers contained within the system controller
+      chip.  The address specified in the "reg" property should match
+      the unit address of the system-controller node.
+    - #address-cells : Address representation for system controller
+      devices.  This field represents the number of cells needed to
+      represent the address of the memory-mapped registers of devices
+      within the system controller chip.
+    - #size-cells : Size representation for the memory-mapped
+      registers within the system controller chip.
+    - #interrupt-cells : Defines the width of cells used to represent
+      interrupts.
+
+  Optional properties:
+
+    - model : The specific model of the system controller chip.  Such
+      as, "mv64360", "mv64460", or "mv64560".
+    - compatible : A string identifying the compatibility identifiers
+      of the system controller chip.
+
+  The system-controller node contains child nodes for each system
+  controller device that the platform uses.  Nodes should not be created
+  for devices which exist on the system controller chip but are not used
+
+  Example Marvell Discovery mv64360 system-controller node:
+
+    system-controller@f1000000 { /* Marvell Discovery mv64360 */
+	    #address-cells = <1>;
+	    #size-cells = <1>;
+	    model = "mv64360";                      /* Default */
+	    compatible = "marvell,mv64360";
+	    clock-frequency = <133333333>;
+	    reg = <0xf1000000 0x10000>;
+	    virtual-reg = <0xf1000000>;
+	    ranges = <0x88000000 0x88000000 0x1000000 /* PCI 0 I/O Space */
+		    0x80000000 0x80000000 0x8000000 /* PCI 0 MEM Space */
+		    0xa0000000 0xa0000000 0x4000000 /* User FLASH */
+		    0x00000000 0xf1000000 0x0010000 /* Bridge's regs */
+		    0xf2000000 0xf2000000 0x0040000>;/* Integrated SRAM */
+
+	    [ child node definitions... ]
+    }
+
+2) Child nodes of /system-controller
+
+   a) Marvell Discovery MDIO bus
+
+   The MDIO is a bus to which the PHY devices are connected.  For each
+   device that exists on this bus, a child node should be created.  See
+   the definition of the PHY node below for an example of how to define
+   a PHY.
+
+   Required properties:
+     - #address-cells : Should be <1>
+     - #size-cells : Should be <0>
+     - device_type : Should be "mdio"
+     - compatible : Should be "marvell,mv64360-mdio"
+
+   Example:
+
+     mdio {
+	     #address-cells = <1>;
+	     #size-cells = <0>;
+	     device_type = "mdio";
+	     compatible = "marvell,mv64360-mdio";
+
+	     ethernet-phy@0 {
+		     ......
+	     };
+     };
+
+
+   b) Marvell Discovery ethernet controller
+
+   The Discover ethernet controller is described with two levels
+   of nodes.  The first level describes an ethernet silicon block
+   and the second level describes up to 3 ethernet nodes within
+   that block.  The reason for the multiple levels is that the
+   registers for the node are interleaved within a single set
+   of registers.  The "ethernet-block" level describes the
+   shared register set, and the "ethernet" nodes describe ethernet
+   port-specific properties.
+
+   Ethernet block node
+
+   Required properties:
+     - #address-cells : <1>
+     - #size-cells : <0>
+     - compatible : "marvell,mv64360-eth-block"
+     - reg : Offset and length of the register set for this block
+
+   Example Discovery Ethernet block node:
+     ethernet-block@2000 {
+	     #address-cells = <1>;
+	     #size-cells = <0>;
+	     compatible = "marvell,mv64360-eth-block";
+	     reg = <0x2000 0x2000>;
+	     ethernet@0 {
+		     .......
+	     };
+     };
+
+   Ethernet port node
+
+   Required properties:
+     - device_type : Should be "network".
+     - compatible : Should be "marvell,mv64360-eth".
+     - reg : Should be <0>, <1>, or <2>, according to which registers
+       within the silicon block the device uses.
+     - interrupts : <a> where a is the interrupt number for the port.
+     - interrupt-parent : the phandle for the interrupt controller
+       that services interrupts for this device.
+     - phy : the phandle for the PHY connected to this ethernet
+       controller.
+     - local-mac-address : 6 bytes, MAC address
+
+   Example Discovery Ethernet port node:
+     ethernet@0 {
+	     device_type = "network";
+	     compatible = "marvell,mv64360-eth";
+	     reg = <0>;
+	     interrupts = <32>;
+	     interrupt-parent = <&PIC>;
+	     phy = <&PHY0>;
+	     local-mac-address = [ 00 00 00 00 00 00 ];
+     };
+
+
+
+   c) Marvell Discovery PHY nodes
+
+   Required properties:
+     - device_type : Should be "ethernet-phy"
+     - interrupts : <a> where a is the interrupt number for this phy.
+     - interrupt-parent : the phandle for the interrupt controller that
+       services interrupts for this device.
+     - reg : The ID number for the phy, usually a small integer
+
+   Example Discovery PHY node:
+     ethernet-phy@1 {
+	     device_type = "ethernet-phy";
+	     compatible = "broadcom,bcm5421";
+	     interrupts = <76>;      /* GPP 12 */
+	     interrupt-parent = <&PIC>;
+	     reg = <1>;
+     };
+
+
+   d) Marvell Discovery SDMA nodes
+
+   Represent DMA hardware associated with the MPSC (multiprotocol
+   serial controllers).
+
+   Required properties:
+     - compatible : "marvell,mv64360-sdma"
+     - reg : Offset and length of the register set for this device
+     - interrupts : <a> where a is the interrupt number for the DMA