Linux-2.6.12-rc2v2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

1 files changed, 1320 insertions, 0 deletions

diff --git a/Documentation/DocBook/mtdnand.tmpl b/Documentation/DocBook/mtdnand.tmpl
new file mode 100644
index 00000000000..6e463d0db26
--- /dev/null
+++ b/Documentation/DocBook/mtdnand.tmpl
@@ -0,0 +1,1320 @@
+<?xml version="1.0" encoding="UTF-8"?>
+<!DOCTYPE book PUBLIC "-//OASIS//DTD DocBook XML V4.1.2//EN"
+	"http://www.oasis-open.org/docbook/xml/4.1.2/docbookx.dtd" []>
+
+<book id="MTD-NAND-Guide">
+ <bookinfo>
+  <title>MTD NAND Driver Programming Interface</title>
+  
+  <authorgroup>
+   <author>
+    <firstname>Thomas</firstname>
+    <surname>Gleixner</surname>
+    <affiliation>
+     <address>
+      <email>tglx@linutronix.de</email>
+     </address>
+    </affiliation>
+   </author>
+  </authorgroup>
+
+  <copyright>
+   <year>2004</year>
+   <holder>Thomas Gleixner</holder>
+  </copyright>
+
+  <legalnotice>
+   <para>
+     This documentation is free software; you can redistribute
+     it and/or modify it under the terms of the GNU General Public
+     License version 2 as published by the Free Software Foundation.
+   </para>
+      
+   <para>
+     This program is distributed in the hope that it will be
+     useful, but WITHOUT ANY WARRANTY; without even the implied
+     warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
+     See the GNU General Public License for more details.
+   </para>
+      
+   <para>
+     You should have received a copy of the GNU General Public
+     License along with this program; if not, write to the Free
+     Software Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+     MA 02111-1307 USA
+   </para>
+      
+   <para>
+     For more details see the file COPYING in the source
+     distribution of Linux.
+   </para>
+  </legalnotice>
+ </bookinfo>
+
+<toc></toc>
+
+  <chapter id="intro">
+      <title>Introduction</title>
+  <para>
+  	The generic NAND driver supports almost all NAND and AG-AND based
+	chips and connects them to the Memory Technology Devices (MTD)
+	subsystem of the Linux Kernel.
+  </para>
+  <para>
+  	This documentation is provided for developers who want to implement
+	board drivers or filesystem drivers suitable for NAND devices.
+  </para>
+  </chapter>
+  
+  <chapter id="bugs">
+     <title>Known Bugs And Assumptions</title>
+  <para>
+	None.	
+  </para>
+  </chapter>
+
+  <chapter id="dochints">
+     <title>Documentation hints</title>
+     <para>
+     The function and structure docs are autogenerated. Each function and 
+     struct member has a short description which is marked with an [XXX] identifier.
+     The following chapters explain the meaning of those identifiers.
+     </para>
+     <sect1>   
+	<title>Function identifiers [XXX]</title>
+     	<para>
+	The functions are marked with [XXX] identifiers in the short
+	comment. The identifiers explain the usage and scope of the
+	functions. Following identifiers are used:
+     	</para>
+	<itemizedlist>
+		<listitem><para>
+	  	[MTD Interface]</para><para>
+		These functions provide the interface to the MTD kernel API. 
+		They are not replacable and provide functionality
+		which is complete hardware independent.
+		</para></listitem>
+		<listitem><para>
+	  	[NAND Interface]</para><para>
+		These functions are exported and provide the interface to the NAND kernel API. 
+		</para></listitem>
+		<listitem><para>
+	  	[GENERIC]</para><para>
+		Generic functions are not replacable and provide functionality
+		which is complete hardware independent.
+		</para></listitem>
+		<listitem><para>
+	  	[DEFAULT]</para><para>
+		Default functions provide hardware related functionality which is suitable
+		for most of the implementations. These functions can be replaced by the
+		board driver if neccecary. Those functions are called via pointers in the
+		NAND chip description structure. The board driver can set the functions which
+		should be replaced by board dependend functions before calling nand_scan().
+		If the function pointer is NULL on entry to nand_scan() then the pointer
+		is set to the default function which is suitable for the detected chip type.
+		</para></listitem>
+	</itemizedlist>
+     </sect1>
+     <sect1>   
+	<title>Struct member identifiers [XXX]</title>
+     	<para>
+	The struct members are marked with [XXX] identifiers in the 
+	comment. The identifiers explain the usage and scope of the
+	members. Following identifiers are used:
+     	</para>
+	<itemizedlist>
+		<listitem><para>
+	  	[INTERN]</para><para>
+		These members are for NAND driver internal use only and must not be
+		modified. Most of these values are calculated from the chip geometry
+		information which is evaluated during nand_scan().
+		</para></listitem>
+		<listitem><para>
+	  	[REPLACEABLE]</para><para>
+		Replaceable members hold hardware related functions which can be 
+		provided by the board driver. The board driver can set the functions which
+		should be replaced by board dependend functions before calling nand_scan().
+		If the function pointer is NULL on entry to nand_scan() then the pointer
+		is set to the default function which is suitable for the detected chip type.
+		</para></listitem>
+		<listitem><para>
+	  	[BOARDSPECIFIC]</para><para>
+		Board specific members hold hardware related information which must
+		be provided by the board driver. The board driver must set the function
+		pointers and datafields before calling nand_scan().
+		</para></listitem>
+		<listitem><para>
+	  	[OPTIONAL]</para><para>
+		Optional members can hold information relevant for the board driver. The
+		generic NAND driver code does not use this information.
+		</para></listitem>
+	</itemizedlist>
+     </sect1>
+  </chapter>   
+
+  <chapter id="basicboarddriver">
+     	<title>Basic board driver</title>
+	<para>
+		For most boards it will be sufficient to provide just the
+		basic functions and fill out some really board dependend
+		members in the nand chip description structure.
+		See drivers/mtd/nand/skeleton for reference.
+	</para>
+	<sect1>
+		<title>Basic defines</title>
+		<para>
+			At least you have to provide a mtd structure and
+			a storage for the ioremap'ed chip address.
+			You can allocate the mtd structure using kmalloc
+			or you can allocate it statically.
+			In case of static allocation you have to allocate
+			a nand_chip structure too.
+		</para>
+		<para>
+			Kmalloc based example
+		</para>
+		<programlisting>
+static struct mtd_info *board_mtd;
+static unsigned long baseaddr;
+		</programlisting>
+		<para>
+			Static example
+		</para>
+		<programlisting>
+static struct mtd_info board_mtd;
+static struct nand_chip board_chip;
+static unsigned long baseaddr;
+		</programlisting>
+	</sect1>
+	<sect1>
+		<title>Partition defines</title>
+		<para>
+			If you want to divide your device into parititions, then
+			enable the configuration switch CONFIG_MTD_PARITIONS and define
+			a paritioning scheme suitable to your board.
+		</para>
+		<programlisting>
+#define NUM_PARTITIONS 2
+static struct mtd_partition partition_info[] = {
+	{ .name = "Flash partition 1",
+	  .offset =  0,
+	  .size =    8 * 1024 * 1024 },
+	{ .name = "Flash partition 2",
+	  .offset =  MTDPART_OFS_NEXT,
+	  .size =    MTDPART_SIZ_FULL },
+};
+		</programlisting>
+	</sect1>
+	<sect1>
+		<title>Hardware control function</title>
+		<para>
+			The hardware control function provides access to the 
+			control pins of the NAND chip(s). 
+			The access can be done by GPIO pins or by address lines.
+			If you use address lines, make sure that the timing
+			requirements are met.
+		</para>
+		<para>
+			<emphasis>GPIO based example</emphasis>
+		</para>
+		<programlisting>
+static void board_hwcontrol(struct mtd_info *mtd, int cmd)
+{
+	switch(cmd){
+		case NAND_CTL_SETCLE: /* Set CLE pin high */ break;
+		case NAND_CTL_CLRCLE: /* Set CLE pin low */ break;
+		case NAND_CTL_SETALE: /* Set ALE pin high */ break;
+		case NAND_CTL_CLRALE: /* Set ALE pin low */ break;
+		case NAND_CTL_SETNCE: /* Set nCE pin low */ break;
+		case NAND_CTL_CLRNCE: /* Set nCE pin high */ break;
+	}
+}
+		</programlisting>
+		<para>
+			<emphasis>Address lines based example.</emphasis> It's assumed that the
+			nCE pin is driven by a chip select decoder.
+		</para>
+		<programlisting>
+static void board_hwcontrol(struct mtd_info *mtd, int cmd)
+{
+	struct nand_chip *this = (struct nand_chip *) mtd->priv;
+	switch(cmd){
+		case NAND_CTL_SETCLE: this->IO_ADDR_W |= CLE_ADRR_BIT;  break;
+		case NAND_CTL_CLRCLE: this->IO_ADDR_W &amp;= ~CLE_ADRR_BIT; break;
+		case NAND_CTL_SETALE: this->IO_ADDR_W |= ALE_ADRR_BIT;  break;
+		case NAND_CTL_CLRALE: this->IO_ADDR_W &amp;= ~ALE_ADRR_BIT; break;
+	}
+}
+		</programlisting>
+	</sect1>
+	<sect1>
+		<title>Device ready function</title>
+		<para>
+			If the hardware interface has the ready busy pin of the NAND chip connected to a
+			GPIO or other accesible I/O pin, this function is used to read back the state of the
+			pin. The function has no arguments and should return 0, if the device is busy (R/B pin 
+			is low) and 1, if the device is ready (R/B pin is high).
+			If the hardware interface does not give access to the ready busy pin, then
+			the function must not be defined and the function pointer this->dev_ready is set to NULL.		
+		</para>
+	</sect1>
+	<sect1>
+		<title>Init function</title>
+		<para>
+			The init function allocates memory and sets up all the board
+			specific parameters and function pointers. When everything
+			is set up nand_scan() is called. This function tries to
+			detect and identify then chip. If a chip is found all the
+			internal data fields are initialized accordingly.
+			The structure(s) have to be zeroed out first and then filled with the neccecary 
+			information about the device.
+		</para>
+		<programlisting>
+int __init board_init (void)
+{
+	struct nand_chip *this;
+	int err = 0;
+
+	/* Allocate memory for MTD device structure and private data */
+	board_mtd = kmalloc (sizeof(struct mtd_info) + sizeof (struct nand_chip), GFP_KERNEL);
+	if (!board_mtd) {
+		printk ("Unable to allocate NAND MTD device structure.\n");
+		err = -ENOMEM;
+		goto out;
+	}
+
+	/* Initialize structures */
+	memset ((char *) board_mtd, 0, sizeof(struct mtd_info) + sizeof(struct nand_chip));
+
+	/* map physical adress */
+	baseaddr = (unsigned long)ioremap(CHIP_PHYSICAL_ADDRESS, 1024);
+	if(!baseaddr){
+		printk("Ioremap to access NAND chip failed\n");
+		err = -EIO;
+		goto out_mtd;
+	}
+
+	/* Get pointer to private data */
+	this = (struct nand_chip *) ();
+	/* Link the private data with the MTD structure */
+	board_mtd->priv = this;
+
+	/* Set address of NAND IO lines */
+	this->IO_ADDR_R = baseaddr;
+	this->IO_ADDR_W = baseaddr;
+	/* Reference hardware control function */
+	this->hwcontrol = board_hwcontrol;
+	/* Set command delay time, see datasheet for correct value */
+	this->chip_delay = CHIP_DEPENDEND_COMMAND_DELAY;
+	/* Assign the device ready function, if available */
+	this->dev_ready = board_dev_ready;
+	this->eccmode = NAND_ECC_SOFT;
+
+	/* Scan to find existance of the device */
+	if (nand_scan (board_mtd, 1)) {
+		err = -ENXIO;
+		goto out_ior;
+	}
+	
+	add_mtd_partitions(board_mtd, partition_info, NUM_PARTITIONS);
+	goto out;
+
+out_ior:
+	iounmap((void *)baseaddr);
+out_mtd:
+	kfree (board_mtd);
+out:
+	return err;
+}
+module_init(board_init);
+		</programlisting>
+	</sect1>
+	<sect1>
+		<title>Exit function</title>
+		<para>
+			The exit function is only neccecary if the driver is
+			compiled as a module. It releases all resources which
+			are held by the chip driver and unregisters the partitions
+			in the MTD layer.
+		</para>
+		<programlisting>
+#ifdef MODULE
+static void __exit board_cleanup (void)
+{
+	/* Release resources, unregister device */
+	nand_release (board_mtd);
+
+	/* unmap physical adress */
+	iounmap((void *)baseaddr);
+	
+	/* Free the MTD device structure */
+	kfree (board_mtd);
+}
+module_exit(board_cleanup);
+#endif
+		</programlisting>
+	</sect1>
+  </chapter>
+
+  <chapter id="boarddriversadvanced">
+     	<title>Advanced board driver functions</title>
+	<para>
+		This chapter describes the advanced functionality of the NAND
+		driver. For a list of functions which can be overridden by the board
+		driver see the documentation of the nand_chip structure.
+	</para>
+	<sect1>
+		<title>Multiple chip control</title>
+		<para>
+			The nand driver can control chip arrays. Therefor the
+			board driver must provide an own select_chip function. This
+			function must (de)select the requested chip.
+			The function pointer in the nand_chip structure must
+			be set before calling nand_scan(). The maxchip parameter
+			of nand_scan() defines the maximum number of chips to
+			scan for. Make sure that the select_chip function can
+			handle the requested number of chips.
+		</para>
+		<para>
+			The nand driver concatenates the chips to one virtual
+			chip and provides this virtual chip to the MTD layer.
+		</para>
+		<para>
+			<emphasis>Note: The driver can only handle linear chip arrays
+			of equally sized chips. There is no support for
+			parallel arrays which extend the buswidth.</emphasis>
+		</para>
+		<para>
+			<emphasis>GPIO based example</emphasis>
+		</para>
+		<programlisting>
+static void board_select_chip (struct mtd_info *mtd, int chip)
+{
+	/* Deselect all chips, set all nCE pins high */
+	GPIO(BOARD_NAND_NCE) |= 0xff;	
+	if (chip >= 0)
+		GPIO(BOARD_NAND_NCE) &amp;= ~ (1 &lt;&lt; chip);
+}
+		</programlisting>
+		<para>
+			<emphasis>Address lines based example.</emphasis>
+			Its assumed that the nCE pins are connected to an
+			address decoder.
+		</para>
+		<programlisting>
+static void board_select_chip (struct mtd_info *mtd, int chip)
+{
+	struct nand_chip *this = (struct nand_chip *) mtd->priv;
+	
+	/* Deselect all chips */
+	this->IO_ADDR_R &amp;= ~BOARD_NAND_ADDR_MASK;
+	this->IO_ADDR_W &amp;= ~BOARD_NAND_ADDR_MASK;
+	switch (chip) {
+	case 0:
+		this->IO_ADDR_R |= BOARD_NAND_ADDR_CHIP0;
+		this->IO_ADDR_W |= BOARD_NAND_ADDR_CHIP0;
+		break;
+	....	
+	case n:
+		this->IO_ADDR_R |= BOARD_NAND_ADDR_CHIPn;
+		this->IO_ADDR_W |= BOARD_NAND_ADDR_CHIPn;
+		break;
+	}	
+}
+		</programlisting>
+	</sect1>
+	<sect1>
+		<title>Hardware ECC support</title>
+		<sect2>
+			<title>Functions and constants</title>
+			<para>
+				The nand driver supports three different types of
+				hardware ECC.
+				<itemizedlist>
+				<listitem><para>NAND_ECC_HW3_256</para><para>
+				Hardware ECC generator providing 3 bytes ECC per
+				256 byte.
+				</para>	</listitem>
+				<listitem><para>NAND_ECC_HW3_512</para><para>
+				Hardware ECC generator providing 3 bytes ECC per
+				512 byte.
+				</para>	</listitem>
+				<listitem><para>NAND_ECC_HW6_512</para><para>
+				Hardware ECC generator providing 6 bytes ECC per
+				512 byte.
+				</para>	</listitem>
+				<listitem><para>NAND_ECC_HW8_512</para><para>
+				Hardware ECC generator providing 6 bytes ECC per
+				512 byte.
+				</para>	</listitem>
+				</itemizedlist>
+				If your hardware generator has a different functionality
+				add it at the appropriate place in nand_base.c
+			</para>
+			<para>
+				The board driver must provide following functions:
+				<itemizedlist>
+				<listitem><para>enable_hwecc</para><para>
+				This function is called before reading / writing to
+				the chip. Reset or initialize the hardware generator
+				in this function. The function is called with an
+				argument which let you distinguish between read 
+				and write operations.
+				</para>	</listitem>
+				<listitem><para>calculate_ecc</para><para>
+				This function is called after read / write from / to
+				the chip. Transfer the ECC from the hardware to
+				the buffer. If the option NAND_HWECC_SYNDROME is set
+				then the function is only called on write. See below.
+				</para>	</listitem>
+				<listitem><para>correct_data</para><para>
+				In case of an ECC error this function is called for
+				error detection and correction. Return 1 respectively 2
+				in case the error can be corrected. If the error is
+				not correctable return -1. If your hardware generator
+				matches the default algorithm of the nand_ecc software
+				generator then use the correction function provided
+				by nand_ecc instead of implementing duplicated code.
+				</para>	</listitem>
+				</itemizedlist>
+			</para>
+		</sect2>
+		<sect2>
+		<title>Hardware ECC with syndrome calculation</title>
+			<para>
+				Many hardware ECC implementations provide Reed-Solomon
+				codes and calculate an error syndrome on read. The syndrome
+				must be converted to a standard Reed-Solomon syndrome
+				before calling the error correction code in the generic
+				Reed-Solomon library.
+			</para>
+			<para>
+				The ECC bytes must be placed immidiately after the data
+				bytes in order to make the syndrome generator work. This
+				is contrary to the usual layout used by software ECC. The
+				seperation of data and out of band area is not longer
+				possible. The nand driver code handles this layout and
+				the remaining free bytes in the oob area are managed by 
+				the autoplacement code. Provide a matching oob-layout
+				in this case. See rts_from4.c and diskonchip.c for 
+				implementation reference. In those cases we must also
+				use bad block tables on FLASH, because the ECC layout is
+				interferring with the bad block marker positions.
+				See bad block table support for details.
+			</para>
+		</sect2>
+	</sect1>
+	<sect1>
+		<title>Bad block table support</title>
+		<para>
+			Most NAND chips mark the bad blocks at a defined
+			position in the spare area. Those blocks must 
+			not be erased under any circumstances as the bad 
+			block information would be lost.
+			It is possible to check the bad block mark each
+			time when the blocks are accessed by reading the
+			spare area of the first page in the block. This
+			is time consuming so a bad block table is used.
+		</para>
+		<para>
+			The nand driver supports various types of bad block
+			tables.
+			<itemizedlist>
+			<listitem><para>Per device</para><para>
+			The bad block table contains all bad block information
+			of the device which can consist of multiple chips.
+			</para>	</listitem>
+			<listitem><para>Per chip</para><para>
+			A bad block table is used per chip and contains the
+			bad block information for this particular chip.
+			</para>	</listitem>
+			<listitem><para>Fixed offset</para><para>
+			The bad block table is located at a fixed offset
+			in the chip (device). This applies to various
+			DiskOnChip devices.
+			</para>	</listitem>
+			<listitem><para>Automatic placed</para><para>
+			The bad block table is automatically placed and
+			detected either at the end or at the beginning
+			of a chip (device)
+			</para>	</listitem>
+			<listitem><para>Mirrored tables</para><para>
+			The bad block table is mirrored on the chip (device) to
+			allow updates of the bad block table without data loss.
+			</para>	</listitem>
+			</itemizedlist>
+		</para>
+		<para>	
+			nand_scan() calls the function nand_default_bbt(). 
+			nand_default_bbt() selects appropriate default
+			bad block table desriptors depending on the chip information
+			which was retrieved by nand_scan().
+		</para>
+		<para>
+			The standard policy is scanning the device for bad 
+			blocks and build a ram based bad block table which
+			allows faster access than always checking the
+			bad block information on the flash chip itself.
+		</para>
+		<sect2>
+			<title>Flash based tables</title>
+			<para>
+				It may be desired or neccecary to keep a bad block table in FLASH. 
+				For AG-AND chips this is mandatory, as they have no factory marked
+				bad blocks. They have factory marked good blocks. The marker pattern
+				is erased when the block is erased to be reused. So in case of
+				powerloss before writing the pattern back to the chip this block 
+				would be lost and added to the bad blocks. Therefor we scan the 
+				chip(s) when we detect them the first time for good blocks and 
+				store this information in a bad block table before erasing any 
+				of the blocks.
+			</para>
+			<para>
+				The blocks in which the tables are stored are procteted against
+				accidental access by marking them bad in the memory bad block
+				table. The bad block table managment functions are allowed
+				to circumvernt this protection.
+			</para>
+			<para>
+				The simplest way to activate the FLASH based bad block table support 
+				is to set the option NAND_USE_FLASH_BBT in the option field of
+				the nand chip structure before calling nand_scan(). For AG-AND
+				chips is this done by default.
+				This activates the default FLASH based bad block table functionality 
+				of the NAND driver. The default bad block table options are
+				<itemizedlist>
+				<listitem><para>Store bad block table per chip</para></listitem>
+				<listitem><para>Use 2 bits per block</para></listitem>
+				<listitem><para>Automatic placement at the end of the chip</para></listitem>
+				<listitem><para>Use mirrored tables with version numbers</para></listitem>
+				<listitem><para>Reserve 4 blocks at the end of the chip</para></listitem>
+				</itemizedlist>
+			</para>
+		</sect2>
+		<sect2>
+			<title>User defined tables</title>
+			<para>
+				User defined tables are created by filling out a 
+				nand_bbt_descr structure and storing the pointer in the
+				nand_chip structure member bbt_td before calling nand_scan(). 
+				If a mirror table is neccecary a second structure must be
+				created and a pointer to this structure must be stored
+				in bbt_md inside the nand_chip structure. If the bbt_md 
+				member is set to NULL then only the main table is used
+				and no scan for the mirrored table is performed.
+			</para>
+			<para>
+				The most important field in the nand_bbt_descr structure
+				is the options field. The options define most of the 
+				table properties. Use the predefined constants from
+				nand.h to define the options.
+				<itemizedlist>
+				<listitem><para>Number of bits per block</para>
+				<para>The supported number of bits is 1, 2, 4, 8.</para></listitem>
+				<listitem><para>Table per chip</para>
+				<para>Setting the constant NAND_BBT_PERCHIP selects that
+				a bad block table is managed for each chip in a chip array.
+				If this option is not set then a per device bad block table
+				is used.</para></listitem>
+				<listitem><para>Table location is absolute</para>
+				<para>Use the option constant NAND_BBT_ABSPAGE and
+				define the absolute page number where the bad block
+				table starts in the field pages. If you have selected bad block
+				tables per chip and you have a multi chip array then the start page
+				must be given for each chip in the chip array. Note: there is no scan
+				for a table ident pattern performed, so the fields 
+				pattern, veroffs, offs, len can be left uninitialized</para></listitem>
+				<listitem><para>Table location is automatically detected</para>
+				<para>The table can either be located in the first or the last good
+				blocks of the chip (device). Set NAND_BBT_LASTBLOCK to place
+				the bad block table at the end of the chip (device). The
+				bad block tables are marked and identified by a pattern which
+				is stored in the spare area of the first page in the block which
+				holds the bad block table. Store a pointer to the pattern  
+				in the pattern field. Further the length of the pattern has to be 
+				stored in len and the offset in the spare area must be given
+				in the offs member of the nand_bbt_descr stucture. For mirrored
+				bad block tables different patterns are mandatory.</para></listitem>
+				<listitem><para>Table creation</para>
+				<para>Set the option NAND_BBT_CREATE to enable the table creation
+				if no table can be found during the scan. Usually this is done only 
+				once if a new chip is found. </para></listitem>
+				<listitem><para>Table write support</para>
+				<para>Set the option NAND_BBT_WRITE to enable the table write support.
+				This allows the update of the bad block table(s) in case a block has
+				to be marked bad due to wear. The MTD interface function block_markbad
+				is calling the update function of the bad block table. If the write
+				support is enabled then the table is updated on FLASH.</para>
+				<para>
+				Note: Write support should only be enabled for mirrored tables with
+				version control.
+				</para></listitem>
+				<listitem><para>Table version control</para>
+				<para>Set the option NAND_BBT_VERSION to enable the table version control.
+				It's highly recommended to enable this for mirrored tables with write
+				support. It makes sure that the risk of loosing the bad block
+				table information is reduced to the loss of the information about the
+				one worn out block which should be marked bad. The version is stored in
+				4 consecutive bytes in the spare area of the device. The position of
+				the version number is defined by the member veroffs in the bad block table
+				descriptor.</para></listitem>
+				<listitem><para>Save block contents on write</para>
+				<para>
+				In case that the block which holds the bad block table does contain
+				other useful information, set the option NAND_BBT_SAVECONTENT. When
+				the bad block table is written then the whole block is read the bad
+				block table is updated and the block is erased and everything is 
+				written back. If this option is not set only the bad block table
+				is written and everything else in the block is ignored and erased.
+				</para></listitem>
+				<listitem><para>Number of reserved blocks</para>
+				<para>
+				For automatic placement some blocks must be reserved for
+				bad block table storage. The number of reserved blocks is defined 
+				in the maxblocks member of the babd block table description structure.
+				Reserving 4 blocks for mirrored tables should be a reasonable number. 
+				This also limits the number of blocks which are scanned for the bad
+				block table ident pattern.
+				</para></listitem>
+				</itemizedlist>
+			</para>
+		</sect2>
+	</sect1>
+	<sect1>
+		<title>Spare area (auto)placement</title>
+		<para>
+			The nand driver implements different possibilities for
+			placement of filesystem data in the spare area, 
+			<itemizedlist>
+			<listitem><para>Placement defined by fs driver</para></listitem>
+			<listitem><para>Automatic placement</para></listitem>
+			</itemizedlist>
+			The default placement function is automatic placement. The
+			nand driver has built in default placement schemes for the
+			various chiptypes. If due to hardware ECC functionality the
+			default placement does not fit then the board driver can
+			provide a own placement scheme.
+		</para>
+		<para>
+			File system drivers can provide a own placement scheme which
+			is used instead of the default placement scheme.
+		</para>
+		<para>
+			Placement schemes are defined by a nand_oobinfo structure
+	     		<programlisting>
+struct nand_oobinfo {
+	int	useecc;
+	int	eccbytes;
+	int	eccpos[24];
+	int	oobfree[8][2];
+};
+	     		</programlisting>
+			<itemizedlist>
+			<listitem><para>useecc</para><para>
+				The useecc member controls the ecc and placement function. The header
+				file include/mtd/mtd-abi.h contains constants to select ecc and
+				placement. MTD_NANDECC_OFF switches off the ecc complete. This is
+				not recommended and available for testing and diagnosis only.
+				MTD_NANDECC_PLACE selects caller defined placement, MTD_NANDECC_AUTOPLACE
+				selects automatic placement.
+			</para></listitem>
+			<listitem><para>eccbytes</para><para>
+				The eccbytes member defines the number of ecc bytes per page.
+			</para></listitem>
+			<listitem><para>eccpos</para><para>
+				The eccpos array holds the byte offsets in the spare area where
+				the ecc codes are placed.
+			</para></listitem>
+			<listitem><para>oobfree</para><para>
+				The oobfree array defines the areas in the spare area which can be
+				used for automatic placement. The information is given in the format
+				{offset, size}. offset defines the start of the usable area, size the
+				length in bytes. More than one area can be defined. The list is terminated
+				by an {0, 0} entry.
+			</para></listitem>
+			</itemizedlist>
+		</para>
+		<sect2>
+			<title>Placement defined by fs driver</title>
+			<para>
+				The calling function provides a pointer to a nand_oobinfo
+				structure which defines the ecc placement. For writes the
+				caller must provide a spare area buffer along with the
+				data buffer. The spare area buffer size is (number of pages) *
+				(size of spare area). For reads the buffer size is
+				(number of pages) * ((size of spare area) + (number of ecc
+				steps per page) * sizeof (int)). The driver stores the
+				result of the ecc check for each tuple in the spare buffer.
+				The storage sequence is 
+			</para>
+			<para>
+				&lt;spare data page 0&gt;&lt;ecc result 0&gt;...&lt;ecc result n&gt;
+			</para>
+			<para>
+				...
+			</para>
+			<para>
+				&lt;spare data page n&gt;&lt;ecc result 0&gt;...&lt;ecc result n&gt;
+			</para>
+			<para>
+				This is a legacy mode used by YAFFS1.
+			</para>
+			<para>
+				If the spare area buffer is NULL then only the ECC placement is
+				done according to the given scheme in the nand_oobinfo structure.
+			</para>
+		</sect2>
+		<sect2>
+			<title>Automatic placement</title>
+			<para>
+				Automatic placement uses the built in defaults to place the
+				ecc bytes in the spare area. If filesystem data have to be stored /
+				read into the spare area then the calling function must provide a
+				buffer. The buffer size per page is determined by the oobfree array in
+				the nand_oobinfo structure.
+			</para>
+			<para>
+				If the spare area buffer is NULL then only the ECC placement is
+				done according to the default builtin scheme.
+			</para>
+		</sect2>
+		<sect2>
+			<title>User space placement selection</title>
+		<para>
+			All non ecc functions like mtd->read and mtd->write use an internal 
+			structure, which can be set by an ioctl. This structure is preset 
+			to the autoplacement default.
+	     		<programlisting>
+	ioctl (fd, MEMSETOOBSEL, oobsel);
+	     		</programlisting>
+			oobsel is a pointer to a user supplied structure of type
+			nand_oobconfig. The contents of this structure must match the 
+			criteria of the filesystem, which will be used. See an example in utils/nandwrite.c.
+		</para>
+		</sect2>
+	</sect1>	
+	<sect1>
+		<title>Spare area autoplacement default schemes</title>
+		<sect2>
+			<title>256 byte pagesize</title>
+<informaltable><tgroup cols="3"><tbody>
+<row>
+<entry>Offset</entry>
+<entry>Content</entry>
+<entry>Comment</entry>
+</row>
+<row>
+<entry>0x00</entry>
+<entry>ECC byte 0</entry>
+<entry>Error correction code byte 0</entry>
+</row>
+<row>
+<entry>0x01</entry>
+<entry>ECC byte 1</entry>
+<entry>Error correction code byte 1</entry>
+</row>
+<row>
+<entry>0x02</entry>
+<entry>ECC byte 2</entry>
+<entry>Error correction code byte 2</entry>
+</row>
+<row>
+<entry>0x03</entry>
+<entry>Autoplace 0</entry>
+<entry></entry>
+</row>
+<row>
+<entry>0x04</entry>
+<entry>Autoplace 1</entry>
+<entry></entry>
+</row>
+<row>
+<entry>0x05</entry>
+<entry>Bad block marker</entry>
+<entry>If any bit in this byte is zero, then this block is bad.
+This applies only to the first page in a block. In the remaining
+pages this byte is reserved</entry>
+</row>
+<row>
+<entry>0x06</entry>
+<entry>Autoplace 2</entry>
+<entry></entry>
+</row>
+<row>
+<entry>0x07</entry>
+<entry>Autoplace 3</entry>
+<entry></entry>
+</row>
+</tbody></tgroup></informaltable>
+		</sect2>
+		<sect2>
+			<title>512 byte pagesize</title>
+<informaltable><tgroup cols="3"><tbody>
+<row>
+<entry>Offset</entry>
+<entry>Content</entry>
+<entry>Comment</entry>
+</row>
+<row>
+<entry>0x00</entry>
+<entry>ECC byte 0</entry>
+<entry>Error correction code byte 0 of the lower 256 Byte data in
+this page</entry>
+</row>
+<row>
+<entry>0x01</entry>
+<entry>ECC byte 1</entry>
+<entry>Error correction code byte 1 of the lower 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x02</entry>
+<entry>ECC byte 2</entry>
+<entry>Error correction code byte 2 of the lower 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x03</entry>
+<entry>ECC byte 3</entry>
+<entry>Error correction code byte 0 of the upper 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x04</entry>
+<entry>reserved</entry>
+<entry>reserved</entry>
+</row>
+<row>
+<entry>0x05</entry>
+<entry>Bad block marker</entry>
+<entry>If any bit in this byte is zero, then this block is bad.
+This applies only to the first page in a block. In the remaining
+pages this byte is reserved</entry>
+</row>
+<row>
+<entry>0x06</entry>
+<entry>ECC byte 4</entry>
+<entry>Error correction code byte 1 of the upper 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x07</entry>
+<entry>ECC byte 5</entry>
+<entry>Error correction code byte 2 of the upper 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x08 - 0x0F</entry>
+<entry>Autoplace 0 - 7</entry>
+<entry></entry>
+</row>
+</tbody></tgroup></informaltable>
+		</sect2>
+		<sect2>
+			<title>2048 byte pagesize</title>
+<informaltable><tgroup cols="3"><tbody>
+<row>
+<entry>Offset</entry>
+<entry>Content</entry>
+<entry>Comment</entry>
+</row>
+<row>
+<entry>0x00</entry>
+<entry>Bad block marker</entry>
+<entry>If any bit in this byte is zero, then this block is bad.
+This applies only to the first page in a block. In the remaining
+pages this byte is reserved</entry>
+</row>
+<row>
+<entry>0x01</entry>
+<entry>Reserved</entry>
+<entry>Reserved</entry>
+</row>
+<row>
+<entry>0x02-0x27</entry>
+<entry>Autoplace 0 - 37</entry>
+<entry></entry>
+</row>
+<row>
+<entry>0x28</entry>
+<entry>ECC byte 0</entry>
+<entry>Error correction code byte 0 of the first 256 Byte data in
+this page</entry>
+</row>
+<row>
+<entry>0x29</entry>
+<entry>ECC byte 1</entry>
+<entry>Error correction code byte 1 of the first 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x2A</entry>
+<entry>ECC byte 2</entry>
+<entry>Error correction code byte 2 of the first 256 Bytes data in
+this page</entry>
+</row>
+<row>
+<entry>0x2B</entry>
+<entry>ECC byte 3</entry>
+<entry>Error correction code byte 0 of the second 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x2C</entry>
+<entry>ECC byte 4</entry>
+<entry>Error correction code byte 1 of the second 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x2D</entry>
+<entry>ECC byte 5</entry>
+<entry>Error correction code byte 2 of the second 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x2E</entry>
+<entry>ECC byte 6</entry>
+<entry>Error correction code byte 0 of the third 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x2F</entry>
+<entry>ECC byte 7</entry>
+<entry>Error correction code byte 1 of the third 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x30</entry>
+<entry>ECC byte 8</entry>
+<entry>Error correction code byte 2 of the third 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x31</entry>
+<entry>ECC byte 9</entry>
+<entry>Error correction code byte 0 of the fourth 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x32</entry>
+<entry>ECC byte 10</entry>
+<entry>Error correction code byte 1 of the fourth 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x33</entry>
+<entry>ECC byte 11</entry>
+<entry>Error correction code byte 2 of the fourth 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x34</entry>
+<entry>ECC byte 12</entry>
+<entry>Error correction code byte 0 of the fifth 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x35</entry>
+<entry>ECC byte 13</entry>
+<entry>Error correction code byte 1 of the fifth 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x36</entry>
+<entry>ECC byte 14</entry>
+<entry>Error correction code byte 2 of the fifth 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x37</entry>
+<entry>ECC byte 15</entry>
+<entry>Error correction code byte 0 of the sixt 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x38</entry>
+<entry>ECC byte 16</entry>
+<entry>Error correction code byte 1 of the sixt 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x39</entry>
+<entry>ECC byte 17</entry>
+<entry>Error correction code byte 2 of the sixt 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x3A</entry>
+<entry>ECC byte 18</entry>
+<entry>Error correction code byte 0 of the seventh 256 Bytes of
+data in this page</entry>
+</row>
+<row>
+<entry>0x3B</entry>
+<entry>ECC byte 19</entry>
+<entry>Error correction code byte 1 of the seventh 256 Bytes of
+data in this page</entry>
+</row>
+<row>
+<entry>0x3C</entry>
+<entry>ECC byte 20</entry>
+<entry>Error correction code byte 2 of the seventh 256 Bytes of
+data in this page</entry>
+</row>
+<row>
+<entry>0x3D</entry>
+<entry>ECC byte 21</entry>
+<entry>Error correction code byte 0 of the eigth 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x3E</entry>
+<entry>ECC byte 22</entry>
+<entry>Error correction code byte 1 of the eigth 256 Bytes of data
+in this page</entry>
+</row>
+<row>
+<entry>0x3F</entry>
+<entry>ECC byte 23</entry>
+<entry>Error correction code byte 2 of the eigth 256 Bytes of data
+in this page</entry>
+</row>
+</tbody></tgroup></informaltable>
+		</sect2>
+     	</sect1>
+  </chapter>
+
+  <chapter id="filesystems">
+     	<title>Filesystem support</title>
+	<para>
+		The NAND driver provides all neccecary functions for a
+		filesystem via the MTD interface.
+	</para>
+	<para>
+		Filesystems must be aware of the NAND pecularities and
+		restrictions. One major restrictions of NAND Flash is, that you cannot 
+		write as often as you want to a page. The consecutive writes to a page, 
+		before erasing it again, are restricted to 1-3 writes, depending on the 
+		manufacturers specifications. This applies similar to the spare area. 
+	</para>
+	<para>
+		Therefor NAND aware filesystems must either write in page size chunks
+		or hold a writebuffer to collect smaller writes until they sum up to 
+		pagesize. Available NAND aware filesystems: JFFS2, YAFFS. 		
+	</para>
+	<para>
+		The spare area usage to store filesystem data is controlled by
+		the spare area placement functionality which is described in one
+		of the earlier chapters.
+	</para>
+  </chapter>	
+  <chapter id="tools">
+     	<title>Tools</title>
+	<para>
+		The MTD project provides a couple of helpful tools to handle NAND Flash.
+		<itemizedlist>
+		<listitem><para>flasherase, flasheraseall: Erase and format FLASH partitions</para></listitem>
+		<listitem><para>nandwrite: write filesystem images to NAND FLASH</para></listitem>
+		<listitem><para>nanddump: dump the contents of a NAND FLASH partitions</para></listitem>
+		</itemizedlist>
+	</para>
+	<para>
+		These tools are aware of the NAND restrictions. Please use those tools
+		instead of complaining about errors which are caused by non NAND aware
+		access methods.
+	</para>
+  </chapter>	
+
+  <chapter id="defines">
+     <title>Constants</title>
+     <para>
+     This chapter describes the constants which might be relevant for a driver developer.
+     </para>
+     <sect1>   
+	<title>Chip option constants</title>
+     	<sect2>   
+		<title>Constants for chip id table</title>
+     		<para>
+		These constants are defined in nand.h. They are ored together to describe
+		the chip functionality.
+     		<programlisting>
+/* Chip can not auto increment pages */
+#define NAND_NO_AUTOINCR	0x00000001
+/* Buswitdh is 16 bit */
+#define NAND_BUSWIDTH_16	0x00000002
+/* Device supports partial programming without padding */
+#define NAND_NO_PADDING		0x00000004
+/* Chip has cache program function */
+#define NAND_CACHEPRG		0x00000008
+/* Chip has copy back function */
+#define NAND_COPYBACK		0x00000010
+/* AND Chip which has 4 banks and a confusing page / block 
+ * assignment. See Renesas datasheet for further information */
+#define NAND_IS_AND		0x00000020
+/* Chip has a array of 4 pages which can be read without
+ * additional ready /busy waits */
+#define NAND_4PAGE_ARRAY	0x00000040 
+		</programlisting>
+     		</para>
+     	</sect2>
+     	<sect2>   
+		<title>Constants for runtime options</title>
+     		<para>
+		These constants are defined in nand.h. They are ored together to describe
+		the functionality.
+     		<programlisting>
+/* Use a flash based bad block table. This option is parsed by the
+ * default bad block table function (nand_default_bbt). */
+#define NAND_USE_FLASH_BBT	0x00010000
+/* The hw ecc generator provides a syndrome instead a ecc value on read 
+ * This can only work if we have the ecc bytes directly behind the 
+ * data bytes. Applies for DOC and AG-AND Renesas HW Reed Solomon generators */
+#define NAND_HWECC_SYNDROME	0x00020000
+		</programlisting>
+     		</para>
+     	</sect2>
+     </sect1>	
+
+     <sect1>   
+	<title>ECC selection constants</title>
+	<para>
+	Use these constants to select the ECC algorithm.
+  	<programlisting>
+/* No ECC. Usage is not recommended ! */
+#define NAND_ECC_NONE		0
+/* Software ECC 3 byte ECC per 256 Byte data */
+#define NAND_ECC_SOFT		1
+/* Hardware ECC 3 byte ECC per 256 Byte data */
+#define NAND_ECC_HW3_256	2
+/* Hardware ECC 3 byte ECC per 512 Byte data */
+#define NAND_ECC_HW3_512	3
+/* Hardware ECC 6 byte ECC per 512 Byte data */
+#define NAND_ECC_HW6_512	4
+/* Hardware ECC 6 byte ECC per 512 Byte data */
+#define NAND_ECC_HW8_512	6
+	</programlisting>
+	</para>
+     </sect1>	
+
+     <sect1>   
+	<title>Hardware control related constants</title>
+	<para>
+	These constants describe the requested hardware access function when
+	the boardspecific hardware control function is called
+  	<programlisting>
+/* Select the chip by setting nCE to low */
+#define NAND_CTL_SETNCE 	1
+/* Deselect the chip by setting nCE to high */
+#define NAND_CTL_CLRNCE		2
+/* Select the command latch by setting CLE to high */
+#define NAND_CTL_SETCLE		3
+/* Deselect the command latch by setting CLE to low */
+#define NAND_CTL_CLRCLE		4
+/* Select the address latch by setting ALE to high */
+#define NAND_CTL_SETALE		5
+/* Deselect the address latch by setting ALE to low */
+#define NAND_CTL_CLRALE		6
+/* Set write protection by setting WP to high. Not used! */
+#define NAND_CTL_SETWP		7
+/* Clear write protection by setting WP to low. Not used! */
+#define NAND_CTL_CLRWP		8
+	</programlisting>
+	</para>
+     </sect1>	
+
+     <sect1>   
+	<title>Bad block table related constants</title>
+	<para>
+	These constants describe the options used for bad block
+	table descriptors.
+  	<programlisting>
+/* Options for the bad block table descriptors */
+
+/* The number of bits used per block in the bbt on the device */
+#define NAND_BBT_NRBITS_MSK	0x0000000F
+#define NAND_BBT_1BIT		0x00000001
+#define NAND_BBT_2BIT		0x00000002
+#define NAND_BBT_4BIT		0x00000004
+#define NAND_BBT_8BIT		0x00000008
+/* The bad block table is in the last good block of the device */
+#define	NAND_BBT_LASTBLOCK	0x00000010
+/* The bbt is at the given page, else we must scan for the bbt */
+#define NAND_BBT_ABSPAGE	0x00000020
+/* The bbt is at the given page, else we must scan for the bbt */
+#define NAND_BBT_SEARCH		0x00000040
+/* bbt is stored per chip on multichip devices */
+#define NAND_BBT_PERCHIP	0x00000080
+/* bbt has a version counter at offset veroffs */
+#define NAND_BBT_VERSION	0x00000100
+/* Create a bbt if none axists */
+#define NAND_BBT_CREATE		0x00000200
+/* Search good / bad pattern through all pages of a block */
+#define NAND_BBT_SCANALLPAGES	0x00000400
+/* Scan block empty during good / bad block scan */
+#define NAND_BBT_SCANEMPTY	0x00000800
+/* Write bbt if neccecary */
+#define NAND_BBT_WRITE		0x00001000
+/* Read and write back block contents when writing bbt */
+#define NAND_BBT_SAVECONTENT	0x00002000
+	</programlisting>
+	</para>
+     </sect1>	
+
+  </chapter>
+  	
+  <chapter id="structs">
+     <title>Structures</title>
+     <para>
+     This chapter contains the autogenerated documentation of the structures which are
+     used in the NAND driver and might be relevant for a driver developer. Each  
+     struct member has a short description which is marked with an [XXX] identifier.
+     See the chapter "Documentation hints" for an explanation.
+     </para>
+!Iinclude/linux/mtd/nand.h
+  </chapter>
+
+  <chapter id="pubfunctions">
+     <title>Public Functions Provided</title>
+     <para>
+     This chapter contains the autogenerated documentation of the NAND kernel API functions
+      which are exported. Each function has a short description which is marked with an [XXX] identifier.
+     See the chapter "Documentation hints" for an explanation.
+     </para>
+!Edrivers/mtd/nand/nand_base.c
+!Edrivers/mtd/nand/nand_bbt.c
+!Edrivers/mtd/nand/nand_ecc.c
+  </chapter>
+  
+  <chapter id="intfunctions">
+     <title>Internal Functions Provided</title>
+     <para>
+     This chapter contains the autogenerated documentation of the NAND driver internal functions.
+     Each function has a short description which is marked with an [XXX] identifier.
+     See the chapter "Documentation hints" for an explanation.
+     The functions marked with [DEFAULT] might be relevant for a board driver developer.
+     </para>
+!Idrivers/mtd/nand/nand_base.c
+!Idrivers/mtd/nand/nand_bbt.c
+!Idrivers/mtd/nand/nand_ecc.c
+  </chapter>
+
+  <chapter id="credits">
+     <title>Credits</title>
+	<para>
+		The following people have contributed to the NAND driver:
+		<orderedlist>
+			<listitem><para>Steven J. Hill<email>sjhill@realitydiluted.com</email></para></listitem>
+			<listitem><para>David Woodhouse<email>dwmw2@infradead.org</email></para></listitem>
+			<listitem><para>Thomas Gleixner<email>tglx@linutronix.de</email></para></listitem>
+		</orderedlist>
+		A lot of users have provided bugfixes, improvements and helping hands for testing.
+		Thanks a lot.
+	</para>
+	<para>
+		The following people have contributed to this document:
+		<orderedlist>
+			<listitem><para>Thomas Gleixner<email>tglx@linutronix.de</email></para></listitem>
+		</orderedlist>
+	</para>
+  </chapter>
+</book>