Merge master.kernel.org:/home/rmk/linux-2.6-arm

* master.kernel.org:/home/rmk/linux-2.6-arm: (22 commits)
  [ARM] 3559/1: S3C2442: core and serial port
  [ARM] 3557/1: S3C24XX: centralise and cleanup uart registration
  [ARM] 3558/1: SMDK24XX: LED platform devices
  [ARM] 3534/1: add spi support to lubbock platform
  [ARM] 3554/1: ARM: Fix dyntick locking
  [ARM] 3553/1: S3C24XX: earlier print of cpu idcode info
  [ARM] 3552/1: S3C24XX: Move VA of GPIO for low-level debug
  [ARM] 3551/1: S3C24XX: PM code failes to compile with CONFIG_DCACHE_WRITETHROUGH
  [ARM] 3550/1: OSIRIS: fix serial port map for 1:1
  [ARM] 3548/1: Fix the ARMv6 CPU id in compressed/head.S
  [ARM] 3335/1: Old-abi Thumb sys_syscall broken
  [ARM] 3467/1: [3/3] Support for Philips PNX4008 platform: defconfig
  [ARM] 3466/1: [2/3] Support for Philips PNX4008 platform: chip support
  [ARM] 3465/1: [1/3] Support for Philips PNX4008 platform: headers
  [ARM] 3407/1: lpd7x: documetation update
  [ARM] 3406/1: lpd7x: compilation fix for smc91x
  [ARM] 3405/1: lpd7a40x: CPLD ssp driver
  [ARM] 3404/1: lpd7a40x: AMBA CLCD support
  [ARM] 3403/1: lpd7a40x: updated default configurations
  [ARM] 3402/1: lpd7a40x: serial driver bug fix
  ...

98 files changed, 9948 insertions, 671 deletions

diff --git a/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen
new file mode 100644
index 00000000000..1e6a23fdf2f
--- /dev/null
+++ b/Documentation/arm/Sharp-LH/ADC-LH7-Touchscreen
@@ -0,0 +1,61 @@
+README on the ADC/Touchscreen Controller
+========================================
+
+The LH79524 and LH7A404 include a built-in Analog to Digital
+controller (ADC) that is used to process input from a touchscreen.
+The driver only implements a four-wire touch panel protocol.
+
+The touchscreen driver is maintenance free except for the pen-down or
+touch threshold.  Some resistive displays and board combinations may
+require tuning of this threshold.  The driver exposes some of it's
+internal state in the sys filesystem.  If the kernel is configured
+with it, CONFIG_SYSFS, and sysfs is mounted at /sys, there will be a
+directory
+
+  /sys/devices/platform/adc-lh7.0
+
+containing these files.
+
+  -r--r--r--    1 root     root         4096 Jan  1 00:00 samples
+  -rw-r--r--    1 root     root         4096 Jan  1 00:00 threshold
+  -r--r--r--    1 root     root         4096 Jan  1 00:00 threshold_range
+
+The threshold is the current touch threshold.  It defaults to 750 on
+most targets.
+
+  # cat threshold
+ 750
+
+The threshold_range contains the range of valid values for the
+threshold.  Values outside of this range will be silently ignored.
+
+  # cat threshold_range
+  0 1023
+
+To change the threshold, write a value to the threshold file.
+
+  # echo 500 > threshold
+  # cat threshold
+  500
+
+The samples file contains the most recently sampled values from the
+ADC.  There are 12.  Below are typical of the last sampled values when
+the pen has been released.  The first two and last two samples are for
+detecting whether or not the pen is down.  The third through sixth are
+X coordinate samples.  The seventh through tenth are Y coordinate
+samples.
+
+  # cat samples
+  1023 1023 0 0 0 0 530 529 530 529 1023 1023
+
+To determine a reasonable threshold, press on the touch panel with an
+appropriate stylus and read the values from samples.
+
+  # cat samples
+  1023 676 92 103 101 102 855 919 922 922 1023 679
+
+The first and eleventh samples are discarded.  Thus, the important
+values are the second and twelfth which are used to determine if the
+pen is down.  When both are below the threshold, the driver registers
+that the pen is down.  When either is above the threshold, it
+registers then pen is up.
diff --git a/Documentation/arm/Sharp-LH/LCDPanels b/Documentation/arm/Sharp-LH/LCDPanels
new file mode 100644
index 00000000000..fb1b21c2f2f
--- /dev/null
+++ b/Documentation/arm/Sharp-LH/LCDPanels
@@ -0,0 +1,59 @@
+README on the LCD Panels
+========================
+
+Configuration options for several LCD panels, available from Logic PD,
+are included in the kernel source.  This README will help you
+understand the configuration data and give you some guidance for
+adding support for other panels if you wish.
+
+
+lcd-panels.h
+------------
+
+There is no way, at present, to detect which panel is attached to the
+system at runtime.  Thus the kernel configuration is static.  The file
+arch/arm/mach-ld7a40x/lcd-panels.h (or similar) defines all of the
+panel specific parameters.
+
+It should be possible for this data to be shared among several device
+families.  The current layout may be insufficiently general, but it is
+amenable to improvement.
+
+
+PIXEL_CLOCK
+-----------
+
+The panel data sheets will give a range of acceptable pixel clocks.
+The fundamental LCDCLK input frequency is divided down by a PCD
+constant in field '.tim2'.  It may happen that it is impossible to set
+the pixel clock within this range.  A clock which is too slow will
+tend to flicker.  For the highest quality image, set the clock as high
+as possible.
+
+
+MARGINS
+-------
+
+These values may be difficult to glean from the panel data sheet.  In
+the case of the Sharp panels, the upper margin is explicitly called
+out as a specific number of lines from the top of the frame.  The
+other values may not matter as much as the panels tend to
+automatically center the image.
+
+
+Sync Sense
+----------
+
+The sense of the hsync and vsync pulses may be called out in the data
+sheet.  On one panel, the sense of these pulses determine the height
+of the visible region on the panel.  Most of the Sharp panels use
+negative sense sync pulses set by the TIM2_IHS and TIM2_IVS bits in
+'.tim2'.
+
+
+Pel Layout
+----------
+
+The Sharp color TFT panels are all configured for 16 bit direct color
+modes.  The amba-lcd driver sets the pel mode to 565 for 5 bits of
+each red and blue and 6 bits of green.
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 08b7cc900ca..f47cf9af3bc 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -270,6 +270,11 @@ config ARCH_AT91RM9200
 	  Say Y here if you intend to run this kernel on an Atmel
 	  AT91RM9200-based board.
 
+config ARCH_PNX4008
+	bool "Philips Nexperia PNX4008 Mobile"
+	help
+	  This enables support for Philips PNX4008 mobile platform.
+
 endchoice
 
 source "arch/arm/mach-clps711x/Kconfig"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 6f8e84c1c1f..6c97aa70d3b 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -116,6 +116,7 @@ endif
  machine-$(CONFIG_ARCH_REALVIEW)   := realview
  machine-$(CONFIG_ARCH_AT91RM9200) := at91rm9200
  machine-$(CONFIG_ARCH_EP93XX)     := ep93xx
+ machine-$(CONFIG_ARCH_PNX4008)    := pnx4008
 
 ifeq ($(CONFIG_ARCH_EBSA110),y)
 # This is what happens if you forget the IOCS16 line.
diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index b56f5e691d6..23016f6aa64 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -605,8 +605,8 @@ proc_types:
 		b	__armv4_mmu_cache_off
 		b	__armv4_mmu_cache_flush
 
-		.word	0x00070000		@ ARMv6
-		.word	0x000f0000
+		.word	0x0007b000		@ ARMv6
+		.word	0x0007f000
 		b	__armv4_mmu_cache_on
 		b	__armv4_mmu_cache_off
 		b	__armv6_mmu_cache_flush
diff --git a/arch/arm/configs/lpd7a400_defconfig b/arch/arm/configs/lpd7a400_defconfig
index 67eaa26c264..bf9cf9c6d2d 100644
--- a/arch/arm/configs/lpd7a400_defconfig
+++ b/arch/arm/configs/lpd7a400_defconfig
@@ -1,7 +1,7 @@
 #
 # Automatically generated make config: don't edit
-# Linux kernel version: 2.6.12-rc1-bk2
-# Mon Mar 28 00:06:33 2005
+# Linux kernel version: 2.6.12
+# Thu Nov  3 14:15:32 2005
 #
 CONFIG_ARM=y
 CONFIG_MMU=y
@@ -17,6 +17,7 @@ CONFIG_EXPERIMENTAL=y
 CONFIG_CLEAN_COMPILE=y
 CONFIG_BROKEN_ON_SMP=y
 CONFIG_LOCK_KERNEL=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
 
 #
 # General setup
@@ -36,6 +37,8 @@ CONFIG_EMBEDDED=y
 CONFIG_KALLSYMS=y
 # CONFIG_KALLSYMS_ALL is not set
 # CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_PRINTK=y
+CONFIG_BUG=y
 CONFIG_BASE_FULL=y
 CONFIG_FUTEX=y
 # CONFIG_EPOLL is not set
@@ -71,6 +74,7 @@ CONFIG_BASE_SMALL=0
 # CONFIG_ARCH_SA1100 is not set
 # CONFIG_ARCH_S3C2410 is not set
 # CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7952X is not set
 CONFIG_ARCH_LH7A40X=y
 # CONFIG_ARCH_OMAP is not set
 # CONFIG_ARCH_VERSATILE is not set
@@ -84,6 +88,7 @@ CONFIG_ARCH_LH7A40X=y
 CONFIG_MACH_LPD7A400=y
 # CONFIG_MACH_LPD7A404 is not set
 CONFIG_ARCH_LH7A400=y
+CONFIG_LPD7A40X_CPLD_SSP=y
 # CONFIG_LH7A40X_CONTIGMEM is not set
 # CONFIG_LH7A40X_ONE_BANK_PER_NODE is not set
 
@@ -110,6 +115,8 @@ CONFIG_ARM_THUMB=y
 #
 # Bus support
 #
+CONFIG_ARM_AMBA=y
+CONFIG_ISA_DMA_API=y
 
 #
 # PCCARD (PCMCIA/CardBus) support
@@ -119,6 +126,7 @@ CONFIG_ARM_THUMB=y
 #
 # Kernel Features
 #
+# CONFIG_SMP is not set
 CONFIG_PREEMPT=y
 CONFIG_DISCONTIGMEM=y
 CONFIG_ALIGNMENT_TRAP=y
@@ -175,7 +183,7 @@ CONFIG_MTD=y
 # CONFIG_MTD_CONCAT is not set
 CONFIG_MTD_PARTITIONS=y
 # CONFIG_MTD_REDBOOT_PARTS is not set
-# CONFIG_MTD_CMDLINE_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
 # CONFIG_MTD_AFS_PARTS is not set
 
 #
@@ -217,7 +225,10 @@ CONFIG_MTD_CFI_UTIL=y
 # Mapping drivers for chip access
 #
 # CONFIG_MTD_COMPLEX_MAPPINGS is not set
-# CONFIG_MTD_PHYSMAP is not set
+CONFIG_MTD_PHYSMAP=y
+CONFIG_MTD_PHYSMAP_START=0x00000000
+CONFIG_MTD_PHYSMAP_LEN=0x04000000
+CONFIG_MTD_PHYSMAP_BANKWIDTH=4
 # CONFIG_MTD_ARM_INTEGRATOR is not set
 # CONFIG_MTD_EDB7312 is not set
 
@@ -254,7 +265,6 @@ CONFIG_MTD_CFI_UTIL=y
 #
 # Block devices
 #
-# CONFIG_BLK_DEV_FD is not set
 # CONFIG_BLK_DEV_COW_COMMON is not set
 CONFIG_BLK_DEV_LOOP=y
 # CONFIG_BLK_DEV_CRYPTOLOOP is not set
@@ -288,13 +298,15 @@ CONFIG_BLK_DEV_IDEDISK=y
 # CONFIG_BLK_DEV_IDECD is not set
 # CONFIG_BLK_DEV_IDETAPE is not set
 # CONFIG_BLK_DEV_IDEFLOPPY is not set
+# CONFIG_BLK_DEV_IDESCSI is not set
 # CONFIG_IDE_TASK_IOCTL is not set
+CONFIG_IDE_POLL=y
 
 #
 # IDE chipset support/bugfixes
 #
 CONFIG_IDE_GENERIC=y
-# CONFIG_IDE_ARM is not set
+CONFIG_IDE_ARM=y
 # CONFIG_BLK_DEV_IDEDMA is not set
 # CONFIG_IDEDMA_AUTO is not set