Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc device tree description updates from Arnd Bergmann:
 "This branch contains two kinds of updates: Some platforms in the
  process of getting converted to device tree based booting, and the
  platform specific patches necessary for that are included here.

  Other platforms are already converted, so we just need to update the
  actual device tree source files and the binding documents to add
  support for new board and new drivers.

  In the future we will probably separate those into two branches, and
  in the long run, the plan is to move the device tree source files out
  of the kernel repository, but that has to wait until we have completed
  a much larger portion of the binding documents."

Fix up trivial conflicts in arch/arm/mach-imx/clk-imx6q.c due to newly
added clkdev registers next to a few removed unnecessary ones.

* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
  ARM: LPC32xx: Add PWM to base dts file
  ARM: EXYNOS: mark the DMA channel binding for SPI as preliminary
  ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
  ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
  ARM: EXYNOS: Add spi clock support for EXYNOS5
  ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
  ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
  ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
  ARM: ux500: Remove PMU platform registration when booting with DT
  ARM: ux500: Remove temporary snowball_of_platform_devs enablement structure
  ARM: ux500: Ensure vendor specific properties have the vendor's identifier
  pinctrl: pinctrl-nomadik: Append sleepmode property with vendor specific prefixes
  ARM: ux500: Move rtc-pl031 registration to Device Tree when enabled
  ARM: ux500: Enable the AB8500 RTC for all DT:ed DB8500 based devices
  ARM: ux500: Correctly reference IRQs supplied by the AB8500 from Device Tree
  ARM: ux500: Apply ab8500-debug node do the db8500 DT structure
  ARM: ux500: Add a ab8500-usb Device Tree node for db8500 based devices
  ARM: ux500: Add db8500 Device Tree node for misc/ab8500-pwm
  ARM: ux500: Add db8500 Device Tree node for ab8500-sysctrl
  ARM: ux500: Enable LED heartbeat functionality on Snowbal via DT
  ...

111 files changed, 4516 insertions, 523 deletions

diff --git a/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt b/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt
new file mode 100644
index 00000000000..597e8a089fe
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/davinci/cp-intc.txt
@@ -0,0 +1,27 @@
+* TI Common Platform Interrupt Controller
+
+Common Platform Interrupt Controller (cp_intc) is used on
+OMAP-L1x SoCs and can support several configurable number
+of interrupts.
+
+Main node required properties:
+
+- compatible : should be:
+	"ti,cp-intc"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The type shall be a <u32> and the value shall be 1.
+
+  The cell contains the interrupt number in the range [0-128].
+- ti,intc-size: Number of interrupts handled by the interrupt controller.
+- reg: physical base address and size of the intc registers map.
+
+Example:
+
+	intc: interrupt-controller@1 {
+		compatible = "ti,cp-intc";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		ti,intc-size = <101>;
+		reg = <0xfffee000 0x2000>;
+	};
diff --git a/Documentation/devicetree/bindings/arm/olimex.txt b/Documentation/devicetree/bindings/arm/olimex.txt
new file mode 100644
index 00000000000..007fb5c685a
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/olimex.txt
@@ -0,0 +1,6 @@
+Olimex i.MX Platforms Device Tree Bindings
+------------------------------------------
+
+i.MX23 Olinuxino Low Cost Board
+Required root node properties:
+    - compatible = "olimex,imx23-olinuxino", "fsl,imx23";
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index e78e8bccac3..f186167dba9 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -47,3 +47,6 @@ Boards:
 
 - AM335X EVM : Software Developement Board for AM335x
   compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3"
+
+- AM335X Bone : Low cost community board
+  compatible = "ti,am335x-bone", "ti,am33xx", "ti,omap3"
diff --git a/Documentation/devicetree/bindings/fb/mxsfb.txt b/Documentation/devicetree/bindings/fb/mxsfb.txt
new file mode 100644
index 00000000000..b41e5e52a67
--- /dev/null
+++ b/Documentation/devicetree/bindings/fb/mxsfb.txt
@@ -0,0 +1,19 @@
+* Freescale MXS LCD Interface (LCDIF)
+
+Required properties:
+- compatible: Should be "fsl,<chip>-lcdif".  Supported chips include
+  imx23 and imx28.
+- reg: Address and length of the register set for lcdif
+- interrupts: Should contain lcdif interrupts
+
+Optional properties:
+- panel-enable-gpios : Should specify the gpio for panel enable
+
+Examples:
+
+lcdif@80030000 {
+	compatible = "fsl,imx28-lcdif";
+	reg = <0x80030000 2000>;
+	interrupts = <38 86>;
+	panel-enable-gpios = <&gpio3 30 0>;
+};
diff --git a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
index 4363ae4b3c1..4f3929713ae 100644
--- a/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
+++ b/Documentation/devicetree/bindings/gpio/fsl-imx-gpio.txt
@@ -8,8 +8,16 @@ Required properties:
   by low 16 pins and the second one is for high 16 pins.
 - gpio-controller : Marks the device node as a gpio controller.
 - #gpio-cells : Should be two.  The first cell is the pin number and
-  the second cell is used to specify optional parameters (currently
-  unused).
+  the second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.  The first cell is the GPIO number.
+  The second cell bits[3:0] is used to specify trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
 
 Example:
 
@@ -19,4 +27,6 @@ gpio0: gpio@73f84000 {
 	interrupts = <50 51>;
 	gpio-controller;
 	#gpio-cells = <2>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
 };
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
index 0c35673f7a3..1e677a47b83 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-mxs.txt
@@ -13,8 +13,9 @@ Required properties for GPIO node:
 - interrupts : Should be the port interrupt shared by all 32 pins.
 - gpio-controller : Marks the device node as a gpio controller.
 - #gpio-cells : Should be two.  The first cell is the pin number and
-  the second cell is used to specify optional parameters (currently
-  unused).
+  the second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
 - interrupt-controller: Marks the device node as an interrupt controller.
 - #interrupt-cells : Should be 2.  The first cell is the GPIO number.
   The second cell bits[3:0] is used to specify trigger type and level flags: