Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (68 commits)
  hwmon: (it87) Add support for the IT8721F/IT8758E
  hwmon: (it87) Move conversion functions
  hwmon: Remove many EXPERIMENTAL flags
  hwmon: (lm85) Add support for ADT7468 high-frequency PWM mode
  hwmon: (lm85) Document the ADT7468 as supported
  hwmon: (lm85) Fix ADT7468 frequency table
  hwmon: I2C addresses are constant
  Move ams driver to macintosh
  hwmon: (pcf8591) Don't attempt to detect devices
  hwmon: (pcf8591) Register as a hwmon device
  hwmon: (w83795) Use standard attributes for chassis intrusion
  hwmon: (w83795) Exclude fan control feature by default
  hwmon: (w83795) Add myself as co-author and maintainer
  hwmon: (w83795) More style cleanups
  hwmon: (w83795) Fix LSB reading of voltage limits
  hwmon: (w83795) Use dev_get_drvdata() where possible
  hwmon: (w83795) Delay reading pwm config registers
  hwmon: (w83795) Delay reading limit registers
  hwmon: (w83795) Move register reads to dedicated functions
  hwmon: (w83795) Pack similar register reads
  ...

27 files changed, 3284 insertions, 556 deletions

diff --git a/Documentation/hwmon/it87 b/Documentation/hwmon/it87
index 8d08bf0d38e..38425f0f264 100644
--- a/Documentation/hwmon/it87
+++ b/Documentation/hwmon/it87
@@ -22,6 +22,10 @@ Supported chips:
     Prefix: 'it8720'
     Addresses scanned: from Super I/O config space (8 I/O ports)
     Datasheet: Not publicly available
+  * IT8721F/IT8758E
+    Prefix: 'it8721'
+    Addresses scanned: from Super I/O config space (8 I/O ports)
+    Datasheet: Not publicly available
   * SiS950   [clone of IT8705F]
     Prefix: 'it87'
     Addresses scanned: from Super I/O config space (8 I/O ports)
@@ -67,7 +71,7 @@ Description
 -----------
 
 This driver implements support for the IT8705F, IT8712F, IT8716F,
-IT8718F, IT8720F, IT8726F and SiS950 chips.
+IT8718F, IT8720F, IT8721F, IT8726F, IT8758E and SiS950 chips.
 
 These chips are 'Super I/O chips', supporting floppy disks, infrared ports,
 joysticks and other miscellaneous stuff. For hardware monitoring, they
@@ -86,14 +90,15 @@ the driver won't notice and report changes in the VID value. The two
 upper VID bits share their pins with voltage inputs (in5 and in6) so you
 can't have both on a given board.
 
-The IT8716F, IT8718F, IT8720F and later IT8712F revisions have support for
-2 additional fans. The additional fans are supported by the driver.
+The IT8716F, IT8718F, IT8720F, IT8721F/IT8758E and later IT8712F revisions
+have support for 2 additional fans. The additional fans are supported by the
+driver.
 
-The IT8716F, IT8718F and IT8720F, and late IT8712F and IT8705F also have
-optional 16-bit tachometer counters for fans 1 to 3. This is better (no more
-fan clock divider mess) but not compatible with the older chips and
-revisions. The 16-bit tachometer mode is enabled by the driver when one
-of the above chips is detected.
+The IT8716F, IT8718F, IT8720F and IT8721F/IT8758E, and late IT8712F and
+IT8705F also have optional 16-bit tachometer counters for fans 1 to 3. This
+is better (no more fan clock divider mess) but not compatible with the older
+chips and revisions. The 16-bit tachometer mode is enabled by the driver when
+one of the above chips is detected.
 
 The IT8726F is just bit enhanced IT8716F with additional hardware
 for AMD power sequencing. Therefore the chip will appear as IT8716F
@@ -115,7 +120,12 @@ alarm is triggered if the voltage has crossed a programmable minimum or
 maximum limit. Note that minimum in this case always means 'closest to
 zero'; this is important for negative voltage measurements. All voltage
 inputs can measure voltages between 0 and 4.08 volts, with a resolution of
-0.016 volt. The battery voltage in8 does not have limit registers.
+0.016 volt (except IT8721F/IT8758E: 0.012 volt.) The battery voltage in8 does
+not have limit registers.
+
+On the IT8721F/IT8758E, some voltage inputs are internal and scaled inside
+the chip (in7, in8 and optionally in3). The driver handles this transparently
+so user-space doesn't have to care.
 
 The VID lines (IT8712F/IT8716F/IT8718F/IT8720F) encode the core voltage value:
 the voltage level your processor should work with. This is hardcoded by
diff --git a/Documentation/hwmon/lm85 b/Documentation/hwmon/lm85
index b98e0e0d191..239258a63c8 100644
--- a/Documentation/hwmon/lm85
+++ b/Documentation/hwmon/lm85
@@ -14,6 +14,10 @@ Supported chips:
     Prefix: 'adt7463'
     Addresses scanned: I2C 0x2c, 0x2d, 0x2e
     Datasheet: http://www.onsemi.com/PowerSolutions/product.do?id=ADT7463
+  * Analog Devices ADT7468
+    Prefix: 'adt7468'
+    Addresses scanned: I2C 0x2c, 0x2d, 0x2e
+    Datasheet: http://www.onsemi.com/PowerSolutions/product.do?id=ADT7468
   * SMSC EMC6D100, SMSC EMC6D101
     Prefix: 'emc6d100'
     Addresses scanned: I2C 0x2c, 0x2d, 0x2e
@@ -34,7 +38,7 @@ Description
 -----------
 
 This driver implements support for the National Semiconductor LM85 and
-compatible chips including the Analog Devices ADM1027, ADT7463 and
+compatible chips including the Analog Devices ADM1027, ADT7463, ADT7468 and
 SMSC EMC6D10x chips family.
 
 The LM85 uses the 2-wire interface compatible with the SMBUS 2.0
@@ -87,14 +91,22 @@ To smooth the response of fans to changes in temperature, the LM85 has an
 optional filter for smoothing temperatures. The ADM1027 has the same
 config option but uses it to rate limit the changes to fan speed instead.
 
-The ADM1027 and ADT7463 have a 10-bit ADC and can therefore measure
-temperatures with 0.25 degC resolution. They also provide an offset to the
-temperature readings that is automatically applied during measurement.
-This offset can be used to zero out any errors due to traces and placement.
-The documentation says that the offset is in 0.25 degC steps, but in
-initial testing of the ADM1027 it was 1.00 degC steps. Analog Devices has
-confirmed this "bug". The ADT7463 is reported to work as described in the
-documentation. The current lm85 driver does not show the offset register.
+The ADM1027, ADT7463 and ADT7468 have a 10-bit ADC and can therefore
+measure temperatures with 0.25 degC resolution. They also provide an offset
+to the temperature readings that is automatically applied during
+measurement. This offset can be used to zero out any errors due to traces
+and placement. The documentation says that the offset is in 0.25 degC
+steps, but in initial testing of the ADM1027 it was 1.00 degC steps. Analog
+Devices has confirmed this "bug". The ADT7463 is reported to work as
+described in the documentation. The current lm85 driver does not show the
+offset register.
+
+The ADT7468 has a high-frequency PWM mode, where all PWM outputs are
+driven by a 22.5 kHz clock. This is a global mode, not per-PWM output,
+which means that setting any PWM frequency above 11.3 kHz will switch
+all 3 PWM outputs to a 22.5 kHz frequency. Conversely, setting any PWM
+frequency below 11.3 kHz will switch all 3 PWM outputs to a frequency
+between 10 and 100 Hz, which can then be tuned separately.
 
 See the vendor datasheets for more information. There is application note
 from National (AN-1260) with some additional information about the LM85.
@@ -125,17 +137,17 @@ datasheet for a complete description of the differences. Other than
 identifying the chip, the driver behaves no differently with regard to
 these two chips. The LM85B is recommended for new designs.
 
-The ADM1027 and ADT7463 chips have an optional SMBALERT output that can be
-used to signal the chipset in case a limit is exceeded or the temperature
-sensors fail. Individual sensor interrupts can be masked so they won't
-trigger SMBALERT. The SMBALERT output if configured replaces one of the other
-functions (PWM2 or IN0). This functionality is not implemented in current
-driver.
+The ADM1027, ADT7463 and ADT7468 chips have an optional SMBALERT output
+that can be used to signal the chipset in case a limit is exceeded or the
+temperature sensors fail. Individual sensor interrupts can be masked so
+they won't trigger SMBALERT. The SMBALERT output if configured replaces one
+of the other functions (PWM2 or IN0). This functionality is not implemented
+in current driver.
 
-The ADT7463 also has an optional THERM output/input which can be connected
-to the processor PROC_HOT output. If available, the autofan control
-dynamic Tmin feature can be enabled to keep the system temperature within
-spec (just?!) with the least possible fan noise.
+The ADT7463 and ADT7468 also have an optional THERM output/input which can
+be connected to the processor PROC_HOT output. If available, the autofan
+control dynamic Tmin feature can be enabled to keep the system temperature
+within spec (just?!) with the least possible fan noise.
 
 Configuration Notes
 -------------------
@@ -201,8 +213,8 @@ the temperatures to compensate for systemic errors in the
 measurements. These features are not currently supported by the lm85
 driver.
 
-In addition to the ADM1027 features, the ADT7463 also has Tmin control
-and THERM asserted counts. Automatic Tmin control acts to adjust the
-Tmin value to maintain the measured temperature sensor at a specified
-temperature. There isn't much documentation on this feature in the
-ADT7463 data sheet. This is not supported by current driver.
+In addition to the ADM1027 features, the ADT7463 and ADT7468 also have
+Tmin control and THERM asserted counts. Automatic Tmin control acts to
+adjust the Tmin value to maintain the measured temperature sensor at a
+specified temperature. There isn't much documentation on this feature in
+the ADT7463 data sheet. This is not supported by current driver.
diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90
index 6a03dd4bcc9..fa475c0a48a 100644
--- a/Documentation/hwmon/lm90
+++ b/Documentation/hwmon/lm90
@@ -63,8 +63,8 @@ Supported chips:
     Datasheet: Publicly available at the Maxim website
                http://www.maxim-ic.com/quick_view2.cfm/qv_pk/2578
   * Maxim MAX6659
-    Prefix: 'max6657'
-    Addresses scanned: I2C 0x4c, 0x4d (unsupported 0x4e)
+    Prefix: 'max6659'
+    Addresses scanned: I2C 0x4c, 0x4d, 0x4e
     Datasheet: Publicly available at the Maxim website
                http://www.maxim-ic.com/quick_view2.cfm/qv_pk/2578
   * Maxim MAX6680
@@ -84,6 +84,21 @@ Supported chips:
     Addresses scanned: I2C 0x4c
     Datasheet: Publicly available at the Maxim website
                http://www.maxim-ic.com/quick_view2.cfm/qv_pk/3500
+  * Maxim MAX6695
+    Prefix: 'max6695'
+    Addresses scanned: I2C 0x18
+    Datasheet: Publicly available at the Maxim website
+               http://www.maxim-ic.com/datasheet/index.mvp/id/4199
+  * Maxim MAX6696
+    Prefix: 'max6695'
+    Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b,
+                           0x4c, 0x4d and 0x4e
+    Datasheet: Publicly available at the Maxim website
+               http://www.maxim-ic.com/datasheet/index.mvp/id/4199
+  * Winbond/Nuvoton W83L771W/G
+    Prefix: 'w83l771'
+    Addresses scanned: I2C 0x4c
+    Datasheet: No longer available
   * Winbond/Nuvoton W83L771AWG/ASG
     Prefix: 'w83l771'
     Addresses scanned: I2C 0x4c
@@ -101,10 +116,11 @@ well as the temperature of up to one external diode. It is compatible
 with many other devices, many of which are supported by this driver.
 
 Note that there is no easy way to differentiate between the MAX6657,
-MAX6658 and MAX6659 variants. The extra address and features of the
-MAX6659 are not supported by this driver. The MAX6680 and MAX6681 only
-differ in their pinout, therefore they obviously can't (and don't need to)
-be distinguished.
+MAX6658 and MAX6659 variants. The extra features of the MAX6659 are only
+supported by this driver if the chip is located at address 0x4d or 0x4e,
+or if the chip type is explicitly selected as max6659.
+The MAX6680 and MAX6681 only differ in their pinout, therefore they obviously
+can't (and don't need to) be distinguished.
 
 The specificity of this family of chipsets over the ADM1021/LM84
 family is that it features critical limits with hysteresis, and an
@@ -151,11 +167,21 @@ MAX6680 and MAX6681:
   * Selectable address
   * Remote sensor type selection
 
+MAX6695 and MAX6696:
+  * Better local resolution
+  * Selectable address (max6696)
+  * Second critical temperature limit
+  * Two remote sensors
+
+W83L771W/G
+  * The G variant is lead-free, otherwise similar to the W.
+  * Filter and alert configuration register at 0xBF
+  * Moving average (depending on conversion rate)
+
 W83L771AWG/ASG
+  * Successor of the W83L771W/G, same features.
   * The AWG and ASG variants only differ in package format.
-  * Filter and alert configuration register at 0xBF
   * Diode ideality factor configuration (remote sensor) at 0xE3
-  * Moving average (depending on conversion rate)
 
 All temperature values are given in degrees Celsius. Resolution
 is 1.0 degree for the local temperature, 0.125 degree for the remote
diff --git a/Documentation/hwmon/pcf8591 b/Documentation/hwmon/pcf8591
index e76a7892f68..ac020b3bb7b 100644
--- a/Documentation/hwmon/pcf8591
+++ b/Documentation/hwmon/pcf8591
@@ -4,7 +4,7 @@ Kernel driver pcf8591
 Supported chips:
   * Philips/NXP PCF8591
     Prefix: 'pcf8591'
-    Addresses scanned: I2C 0x48 - 0x4f
+    Addresses scanned: none
     Datasheet: Publicly available at the NXP website
                http://www.nxp.com/pip/PCF8591_6.html
 
@@ -58,18 +58,16 @@ Module parameters
 Accessing PCF8591 via /sys interface
 -------------------------------------
 
-! Be careful !
-The PCF8591 is plainly impossible to detect! Stupid chip.
-So every chip with address in the interval [0x48..0x4f] is
-detected as PCF8591. If you have other chips in this address
-range, the workaround is to load this module after the one
-for your others chips.
+The PCF8591 is plainly impossible to detect! Thus the driver won't even
+try. You have to explicitly instantiate the device at the relevant
+address (in the interval [0x48..0x4f]) either through platform data, or
+using the sysfs interface. See Documentation/i2c/instantiating-devices
+for details.
 
-On detection (i.e. insmod, modprobe et al.), directories are being
-created for each detected PCF8591:
+Directories are being created for each instantiated PCF8591:
 
 /sys/bus/i2c/devices/<0>-<1>/
-where <0> is the bus the chip was detected on (e. g. i2c-0)
+where <0> is the bus the chip is connected to (e. g. i2c-0)
 and <1> the chip address ([48..4f])
 
 Inside these directories, there are such files:
diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface
index 48ceabedf55..64569901055 100644
--- a/Documentation/hwmon/sysfs-interface
+++ b/Documentation/hwmon/sysfs-interface
@@ -309,6 +309,20 @@ temp[1-*]_crit_hyst
 		from the critical value.
 		RW
 
+temp[1-*]_emergency
+		Temperature emergency max value, for chips supporting more than
+		two upper temperature limits. Must be equal or greater than
+		corresponding temp_crit values.
+		Unit: millidegree Celsius
+		RW
+
+temp[1-*]_emergency_hyst
+		Temperature hysteresis value for emergency limit.
+		Unit: millidegree Celsius
+		Must be reported as an absolute temperature, NOT a delta
+		from the emergency value.
+		RW
+
 temp[1-*]_lcrit	Temperature critical min value, typically lower than
 		corresponding temp_min values.
 		Unit: millidegree Celsius
@@ -505,6 +519,7 @@ fan[1-*]_max_alarm
 temp[1-*]_min_alarm
 temp[1-*]_max_alarm
 temp[1-*]_crit_alarm
+temp[1-*]_emergency_alarm
 		Limit alarm
 		0: no alarm
 		1: alarm
diff --git a/MAINTAINERS b/MAINTAINERS
index ba9480edf8f..d0c2206fd63 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -432,7 +432,7 @@ AMS (Apple Motion Sensor) DRIVER
 M:	Stelian Pop <stelian@popies.net>
 M:	Michael Hanselmann <linux-kernel@hansmi.ch>
 S:	Supported
-F:	drivers/hwmon/ams/
+F:	drivers/macintosh/ams/
 
 AMSO1100 RNIC DRIVER
 M:	Tom Tucker <tom@opengridcomputing.com>
@@ -6465,6 +6465,12 @@ S:	Maintained
 F:	Documentation/hwmon/w83793
 F:	drivers/hwmon/w83793.c
 
+W83795 HARDWARE MONITORING DRIVER
+M:	Jean Delvare <khali@linux-fr.org>
+L:	lm-sensors@lm-sensors.org
+S:	Maintained
+F:	drivers/hwmon/w83795.c
+
 W83L51xD SD/MMC CARD INTERFACE DRIVER
 M:	Pierre Ossman <pierre@ossman.eu>
 S:	Maintained
diff --git a/drivers/hwmon/Kconfig b/drivers/hwmon/Kconfig
index c357c835eb1..a56f6adf3b7 100644
--- a/drivers/hwmon/Kconfig
+++ b/drivers/hwmon/Kconfig
@@ -129,7 +129,7 @@ config SENSORS_ADM1025
 
 config SENSORS_ADM1026
 	tristate "Analog Devices ADM1026 and compatibles"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	select HWMON_VID
 	help
 	  If you say yes here you get support for Analog Devices ADM1026
@@ -140,7 +140,7 @@ config SENSORS_ADM1026
 
 config SENSORS_ADM1029
 	tristate "Analog Devices ADM1029"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	help
 	  If you say yes here you get support for Analog Devices ADM1029
 	  sensor chip.
@@ -151,7 +151,7 @@ config SENSORS_ADM1029
 
 config SENSORS_ADM1031
 	tristate "Analog Devices ADM1031 and compatibles"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	help
 	  If you say yes here you get support for Analog Devices ADM1031
 	  and ADM1030 sensor chips.
@@ -202,7 +202,7 @@ config SENSORS_ADT7470
 
 config SENSORS_ADT7475
 	tristate "Analog Devices ADT7473, ADT7475, ADT7476 and ADT7490"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	select HWMON_VID
 	help
 	  If you say yes here you get support for the Analog Devices
@@ -249,32 +249,6 @@ config SENSORS_K10TEMP
 	  This driver can also be built as a module.  If so, the module
 	  will be called k10temp.
 
-config SENSORS_AMS
-	tristate "Apple Motion Sensor driver"
-	depends on PPC_PMAC && !PPC64 && INPUT && ((ADB_PMU && I2C = y) || (ADB_PMU && !I2C) || I2C) && EXPERIMENTAL
-	select INPUT_POLLDEV
-	help
-	  Support for the motion sensor included in PowerBooks. Includes
-	  implementations for PMU and I2C.
-
-	  This driver can also be built as a module. If so, the module
-	  will be called ams.
-
-config SENSORS_AMS_PMU
-	bool "PMU variant"
-	depends on SENSORS_AMS && ADB_PMU
-	default y
-	help
-	  PMU variant of motion sensor, found in late 2005 PowerBooks.
-
-config SENSORS_AMS_I2C
-	bool "I2C variant"
-	depends on SENSORS_AMS && I2C
-	default y
-	help
-	  I2C variant of motion sensor, found in early 2005 PowerBooks and
-	  iBooks.
-
 config SENSORS_ASB100
 	tristate "Asus ASB100 Bach"
 	depends on X86 && I2C && EXPERIMENTAL
@@ -322,7 +296,6 @@ config SENSORS_I5K_AMB
 
 config SENSORS_F71805F
 	tristate "Fintek F71805F/FG, F71806F/FG and F71872F/FG"
-	depends on EXPERIMENTAL
 	help
 	  If you say yes here you get support for hardware monitoring
 	  features of the Fintek F71805F/FG, F71806F/FG and F71872F/FG
@@ -333,7 +306,6 @@ config SENSORS_F71805F
 
 config SENSORS_F71882FG
 	tristate "Fintek F71858FG, F71862FG, F71882FG, F71889FG and F8000"
-	depends on EXPERIMENTAL
 	help
 	  If you say yes here you get support for hardware monitoring
 	  features of the Fintek F71858FG, F71862FG/71863FG, F71882FG/F71883FG,
@@ -343,8 +315,8 @@ config SENSORS_F71882FG
 	  will be called f71882fg.
 
 config SENSORS_F75375S
-	tristate "Fintek F75375S/SP and F75373";
-	depends on I2C && EXPERIMENTAL
+	tristate "Fintek F75375S/SP and F75373"
+	depends on I2C
 	help
 	  If you say yes here you get support for hardware monitoring
 	  features of the Fintek F75375S/SP and F75373
@@ -456,8 +428,8 @@ config SENSORS_IT87
 	select HWMON_VID
 	help
 	  If you say yes here you get support for ITE IT8705F, IT8712F,
-	  IT8716F, IT8718F, IT8720F and IT8726F sensor chips, and the
-	  SiS960 clone.
+	  IT8716F, IT8718F, IT8720F, IT8721F, IT8726F and IT8758E sensor
+	  chips, and the SiS960 clone.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called it87.
@@ -499,7 +471,7 @@ config SENSORS_LM63
 
 config SENSORS_LM70
 	tristate "National Semiconductor LM70 / Texas Instruments TMP121"
-	depends on SPI_MASTER && EXPERIMENTAL
+	depends on SPI_MASTER
 	help
 	  If you say yes here you get support for the National Semiconductor
 	  LM70 and Texas Instruments TMP121/TMP123 digital temperature
@@ -567,7 +539,7 @@ config SENSORS_LM78
 
 config SENSORS_LM80
 	tristate "National Semiconductor LM80"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	help
 	  If you say yes here you get support for National Semiconductor
 	  LM80 sensor chips.
@@ -587,11 +559,12 @@ config SENSORS_LM83
 
 config SENSORS_LM85
 	tristate "National Semiconductor LM85 and compatibles"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	select HWMON_VID
 	help
 	  If you say yes here you get support for National Semiconductor LM85
-	  sensor chips and clones: ADT7463, EMC6D100, EMC6D102 and ADM1027.
+	  sensor chips and clones: ADM1027, ADT7463, ADT7468, EMC6D100,
+	  EMC6D101 and EMC6D102.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called lm85.
@@ -614,8 +587,8 @@ config SENSORS_LM90
 	  If you say yes here you get support for National Semiconductor LM90,
 	  LM86, LM89 and LM99, Analog Devices ADM1032 and ADT7461, Maxim
 	  MAX6646, MAX6647, MAX6648, MAX6649, MAX6657, MAX6658, MAX6659,
-	  MAX6680, MAX6681 and MAX6692, and Winbond/Nuvoton W83L771AWG/ASG
-	  sensor chips.
+	  MAX6680, MAX6681, MAX6692, MAX6695, MAX6696, and Winbond/Nuvoton
+	  W83L771W/G/AWG/ASG sensor chips.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called lm90.
@@ -726,7 +699,6 @@ config SENSORS_PC87360
 
 config SENSORS_PC87427
 	tristate "National Semiconductor PC87427"
-	depends on EXPERIMENTAL
 	help
 	  If you say yes here you get access to the hardware monitoring
 	  functions of the National Semiconductor PC87427 Super-I/O chip.
@@ -763,14 +735,14 @@ config SENSORS_SHT15
 	  will be called sht15.
 
 config SENSORS_S3C
-	tristate "S3C24XX/S3C64XX Inbuilt ADC"
-	depends on ARCH_S3C2410
+	tristate "Samsung built-in ADC"
+	depends on S3C_ADC
 	help
 	  If you say yes here you get support for the on-board ADCs of
-	  the Samsung S3C24XX or S3C64XX series of SoC
+	  the Samsung S3C24XX, S3C64XX and other series of SoC
 
 	  This driver can also be built as a module. If so, the module
-	  will be called s3c-hwmo.
+	  will be called s3c-hwmon.
 
 config SENSORS_S3C_RAW
 	bool "Include raw channel attributes in sysfs"
@@ -854,7 +826,7 @@ config SENSORS_SMSC47M1
 
 config SENSORS_SMSC47M192
 	tristate "SMSC LPC47M192 and compatibles"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	select HWMON_VID
 	help
 	  If you say yes here you get support for the temperature and
@@ -910,7 +882,7 @@ config SENSORS_AMC6821
 
 config SENSORS_THMC50
 	tristate "Texas Instruments THMC50 / Analog Devices ADM1022"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	help
 	  If you say yes here you get support for Texas Instruments THMC50
 	  sensor chips and clones: the Analog Devices ADM1022.
@@ -968,7 +940,6 @@ config SENSORS_VIA686A
 
 config SENSORS_VT1211
 	tristate "VIA VT1211"
-	depends on EXPERIMENTAL
 	select HWMON_VID
 	help
 	  If you say yes here then you get support for hardware monitoring
@@ -1012,7 +983,7 @@ config SENSORS_W83791D
 
 config SENSORS_W83792D
 	tristate "Winbond W83792D"
-	depends on I2C && EXPERIMENTAL
+	depends on I2C
 	help
 	  If you say yes here you get support for the Winbond W83792D chip.
 
@@ -1031,6 +1002,33 @@ config SENSORS_W83793
 	  This driver can also be built as a module.  If so, the module
 	  will be called w83793.
 
+config SENSORS_W83795
+	tristate "Winbond/Nuvoton W83795G/ADG"
+	depends on I2C && EXPERIMENTAL
+	help
+	  If you say yes here you get support for the Winbond W83795G and
+	  W83795ADG hardware monitoring chip.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called w83795.
+
+config SENSORS_W83795_FANCTRL
+	boolean "Include fan control support (DANGEROUS)"
+	depends on SENSORS_W83795 && EXPERIMENTAL
+	default n
+	help
+	  If you say yes here, support for the both manual and automatic
+	  fan control features will be included in the driver.
+
+	  This part of the code wasn't carefully reviewed and tested yet,
+	  so enabling this option is strongly discouraged on production
+	  servers. Only developers and testers should enable it for the
+	  time being.
+
+	  Please also note that this option will create sysfs attribute
+	  files which may change in the future, so you shouldn't rely
+	  on them being stable.
+
 config SENSORS_W83L785TS
 	tristate "Winbond W83L785TS-S"
 	depends on I2C && EXPERIMENTAL
diff --git a/drivers/hwmon/Makefile b/drivers/hwmon/Makefile
index d30f0f6870e..2479b3da272 100644
--- a/drivers/hwmon/Makefile
+++ b/drivers/hwmon/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_SENSORS_ASB100)	+= asb100.o
 obj-$(CONFIG_SENSORS_W83627HF)	+= w83627hf.o
 obj-$(CONFIG_SENSORS_W83792D)	+= w83792d.o
 obj-$(CONFIG_SENSORS_W83793)	+= w83793.o
+obj-$(CONFIG_SENSORS_W83795)	+= w83795.o
 obj-$(CONFIG_SENSORS_W83781D)	+= w83781d.o
 obj-$(CONFIG_SENSORS_W83791D)	+= w83791d.o
 
@@ -35,7 +36,6 @@ obj-$(CONFIG_SENSORS_ADT7462)	+= adt7462.o
 obj-$(CONFIG_SENSORS_ADT7470)	+= adt7470.o
 obj-$(CONFIG_SENSORS_ADT7475)	+= adt7475.o
 obj-$(CONFIG_SENSORS_APPLESMC)	+= applesmc.o
-obj-$(CONFIG_SENSORS_AMS)	+= ams/
 obj-$(CONFIG_SENSORS_ASC7621)	+= asc7621.o
 obj-$(CONFIG_SENSORS_ATXP1)	+= atxp1.o
 obj-$(CONFIG_SENSORS_CORETEMP)	+= coretemp.o
diff --git a/drivers/hwmon/adt7475.c b/drivers/hwmon/adt7475.c
index a0c38514568..b5fcd87931c 100644
--- a/drivers/hwmon/adt7475.c
+++ b/drivers/hwmon/adt7475.c
@@ -146,7 +146,7 @@
 #define TEMP_OFFSET_REG(idx) (REG_TEMP_OFFSET_BASE + (idx))
 #define TEMP_TRANGE_REG(idx) (REG_TEMP_TRANGE_BASE + (idx))
 
-static unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
+static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
 
 enum chips { adt7473, adt7475, adt7476, adt7490 };
 
diff --git a/drivers/hwmon/asc7621.c b/drivers/hwmon/asc7621.c
index 89b4f3babe8..d2596cec18b 100644
--- a/drivers/hwmon/asc7621.c
+++ b/drivers/hwmon/asc7621.c
@@ -28,7 +28,7 @@
 #include <linux/mutex.h>
 
 /* Addresses to scan */
-static unsigned short normal_i2c[] = {
+static const unsigned short normal_i2c[] = {
 	0x2c, 0x2d, 0x2e, I2C_CLIENT_END
 };
 
@@ -52,7 +52,7 @@ struct asc7621_chip {
 	u8 company_id;
 	u8 verstep_reg;
 	u8 verstep_id;
-	unsigned short *addresses;
+	const unsigned short *addresses;
 };
 
 static struct asc7621_chip asc7621_chips[] = {
diff --git a/drivers/hwmon/it87.c b/drivers/hwmon/it87.c
index f7701295937..14a5d981be7 100644
--- a/drivers/hwmon/it87.c
+++ b/drivers/hwmon/it87.c
@@ -15,7 +15,9 @@
  *            IT8716F  Super I/O chip w/LPC interface
  *            IT8718F  Super I/O chip w/LPC interface
  *            IT8720F  Super I/O chip w/LPC interface
+ *            IT8721F  Super I/O chip w/LPC interface
  *            IT8726F  Super I/O chip w/LPC interface
+ *            IT8758E  Super I/O chip w/LPC interface
  *            Sis950   A clone of the IT8705F
  *
  *  Copyright (C) 2001 Chris Gauthron
@@ -54,7 +56,7 @@
 
 #define DRVNAME "it87"
 
-enum chips { it87, it8712, it8716, it8718, it8720 };
+enum chips { it87, it8712, it8716, it8718, it8720, it8721 };
 
 static unsigned short force_id;
 module_param(force_id, ushort, 0);
@@ -126,6 +128,7 @@ superio_exit(void)
 #define IT8716F_DEVID 0x8716
 #define IT8718F_DEVID 0x8718
 #define IT8720F_DEVID 0x8720
+#define IT8721F_DEVID 0x8721
 #define IT8726F_DEVID 0x8726
 #define IT87_ACT_REG  0x30
 #define IT87_BASE_REG 0x60
@@ -202,56 +205,6 @@ static const u8 IT87_REG_FANX_MIN[]	= { 0x1b, 0x1c, 0x1d, 0x85, 0x87 };
 #define IT87_REG_AUTO_TEMP(nr, i) (0x60 + (nr) * 8 + (i))
 #define IT87_REG_AUTO_PWM(nr, i)  (0x65 + (nr) * 8 + (i))
 
-#define IN_TO_REG(val)  (SENSORS_LIMIT((((val) + 8)/16),0,255))
-#define IN_FROM_REG(val) ((val) * 16)
-
-static inline u8 FAN_TO_REG(long rpm, int div)
-{
-	if (rpm == 0)
-		return 255;
-	rpm = SENSORS_LIMIT(rpm, 1, 1000000);
-	return SENSORS_LIMIT((1350000 + rpm * div / 2) / (rpm * div), 1,
-			     254);
-}
-
-static inline u16 FAN16_TO_REG(long rpm)
-{
-	if (rpm == 0)
-		return 0xffff;
-	return SENSORS_LIMIT((1350000 + rpm) / (rpm * 2), 1, 0xfffe);
-}
-
-#define FAN_FROM_REG(val,div) ((val)==0?-1:(val)==255?0:1350000/((val)*(div)))
-/* The divider is fixed to 2 in 16-bit mode */
-#define FAN16_FROM_REG(val) ((val)==0?-1:(val)==0xffff?0:1350000/((val)*2))
-
-#define TEMP_TO_REG(val) (SENSORS_LIMIT(((val)<0?(((val)-500)/1000):\
-					((val)+500)/1000),-128,127))
-#define TEMP_FROM_REG(val) ((val) * 1000)
-
-#define PWM_TO_REG(val)   ((val) >> 1)
-#define PWM_FROM_REG(val) (((val)&0x7f) << 1)
-
-static int DIV_TO_REG(int val)
-{
-	int answer = 0;
-	while (answer < 7 && (val >>= 1))
-		answer++;
-	return answer;
-}
-#define DIV_FROM_REG(val) (1 << (val))
-
-static const unsigned int pwm_freq[8] = {
-	48000000 / 128,
-	24000000 / 128,
-	12000000 / 128,
-	8000000 / 128,
-	6000000 / 128,
-	3000000 / 128,
-	1500000 / 128,
-	750000 / 128,
-};
-
 
 struct it87_sio_data {
 	enum chips type;
@@ -279,6 +232,7 @@ struct it87_data {
 	char valid;		/* !=0 if following fields are valid */
 	unsigned long last_updated;	/* In jiffies */
 
+	u16 in_scaled;		/* Internal voltage sensors are scaled */
 	u8 in[9];		/* Register value */
 	u8 in_max[8];		/* Register value */
 	u8 in_min[8];		/* Register value */
@@ -310,6 +264,96 @@ struct it87_data {
 	s8 auto_temp[3][5];	/* [nr][0] is point1_temp_hyst */
 };
 
+static u8 in_to_reg(const struct it87_data *data, int nr, long val)
+{
+	long lsb;
+
+	if (data->type == it8721) {
+		if (data->in_scaled & (1 << nr))</