Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull non-critical ARM SoC bug fixes from Arnd Bergmann:
 "Bug fixes that did not make it into v3.8, mostly because they were not
  considered important enough, and in some cases because bugs only show
  up in combination with other patches destined for 3.9.  This includes
  a few larger patches for GPIO on the Marvell PXA platform and a lot of
  Samsung specific bug fixes, as well as a series from Arnd to fix older
  build warnings."

* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  ARM: SPEAr13xx: Enable CONFIG_ARCH_HAS_CPUFREQ
  ARM: imx: MACH_MX31ADS_WM1133_EV1 needs REGULATOR_WM8350
  scripts/sortextable: silence script output
  ARM: s3c: i2c: add platform_device forward declaration
  ARM: mvebu: allow selecting mvebu without Armada XP
  ARM: pick Versatile by default for !MMU
  ARM: integrator: fix build with INTEGRATOR_AP off
  ARM: integrator/versatile: fix NOMMU warnings
  ARM: sa1100: don't warn about mach/ide.h
  ARM: shmobile: fix defconfig warning on CONFIG_USB
  ARM: w90x900: fix legacy assembly syntax
  ARM: samsung: fix assembly syntax for new gas
  ARM: disable virt_to_bus/virt_to_bus almost everywhere
  ARM: dts: Correct pin configuration of SD 4 for exynos4x12-pinctrl
  ARM: SAMSUNG: Silence empty switch warning in fimc-core.h
  ARM: SAMSUNG: Silence empty switch warning in sdhci.h
  ARM: msm: proc_comm_boot_wait should not be __init
  arm: vt8500: Update MAINTAINERS entry for arch-vt8500
  ARM: integrator: ensure ap_syscon_base is initialised when !CONFIG_MMU
  ARM: S5PV210: Fix early uart output in fifo mode
  ...

71 files changed, 252 insertions, 152 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
index e97a27856b2..4598a47aa0c 100644
--- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -7,9 +7,9 @@ on-chip controllers onto these pads.
 
 Required Properties:
 - compatible: should be one of the following.
-  - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
-  - "samsung,pinctrl-exynos4x12": for Exynos4x12 compatible pin-controller.
-  - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
+  - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller.
+  - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller.
+  - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller.
 
 - reg: Base address of the pin controller hardware module and length of
   the address space it occupies.
@@ -142,7 +142,7 @@ the following format 'pinctrl{n}' where n is a unique number for the alias.
 Example: A pin-controller node with pin banks:
 
 	pinctrl_0: pinctrl@11400000 {
-		compatible = "samsung,pinctrl-exynos4210";
+		compatible = "samsung,exynos4210-pinctrl";
 		reg = <0x11400000 0x1000>;
 		interrupts = <0 47 0>;
 
@@ -185,7 +185,7 @@ Example: A pin-controller node with pin banks:
 Example 1: A pin-controller node with pin groups.
 
 	pinctrl_0: pinctrl@11400000 {
-		compatible = "samsung,pinctrl-exynos4210";
+		compatible = "samsung,exynos4210-pinctrl";
 		reg = <0x11400000 0x1000>;
 		interrupts = <0 47 0>;
 
@@ -230,7 +230,7 @@ Example 1: A pin-controller node with pin groups.
 Example 2: A pin-controller node with external wakeup interrupt controller node.
 
 	pinctrl_1: pinctrl@11000000 {
-		compatible = "samsung,pinctrl-exynos4210";
+		compatible = "samsung,exynos4210-pinctrl";
 		reg = <0x11000000 0x1000>;
 		interrupts = <0 46 0>
 
diff --git a/MAINTAINERS b/MAINTAINERS
index f5b9851755a..22b754a8b4b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1256,12 +1256,17 @@ M:	Tony Prisk <linux@prisktech.co.nz>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-vt8500/
+F:	drivers/clocksource/vt8500_timer.c
+F:	drivers/gpio/gpio-vt8500.c
+F:	drivers/mmc/host/wmt-sdmmc.c
+F:	drivers/pwm/pwm-vt8500.c
+F:	drivers/rtc/rtc-vt8500.c
+F:	drivers/tty/serial/vt8500_serial.c
+F:	drivers/usb/host/ehci-vt8500.c
+F:	drivers/usb/host/uhci-platform.c
 F:	drivers/video/vt8500lcdfb.*
 F:	drivers/video/wm8505fb*
 F:	drivers/video/wmt_ge_rops.*
-F:	drivers/tty/serial/vt8500_serial.c
-F:	drivers/rtc/rtc-vt8500.c
-F:	drivers/mmc/host/wmt-sdmmc.c
 
 ARM/ZIPIT Z2 SUPPORT
 M:	Marek Vasut <marek.vasut@gmail.com>
@@ -1270,6 +1275,14 @@ S:	Maintained
 F:	arch/arm/mach-pxa/z2.c
 F:	arch/arm/mach-pxa/include/mach/z2.h
 
+ARM/ZYNQ ARCHITECTURE
+M:	Michal Simek <michal.simek@xilinx.com>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+W:	http://wiki.xilinx.com
+T:	git git://git.xilinx.com/linux-xlnx.git
+S:	Supported
+F:	arch/arm/mach-zynq/
+
 ARM64 PORT (AARCH64 ARCHITECTURE)
 M:	Catalin Marinas <catalin.marinas@arm.com>
 M:	Will Deacon <will.deacon@arm.com>
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index f410cb16dd2..09238c83e6d 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -260,7 +260,8 @@ config MMU
 #
 choice
 	prompt "ARM system type"
-	default ARCH_MULTIPLATFORM
+	default ARCH_VERSATILE if !MMU
+	default ARCH_MULTIPLATFORM if MMU
 
 config ARCH_MULTIPLATFORM
 	bool "Allow multiple platforms to be selected"
@@ -1449,6 +1450,10 @@ config ISA_DMA
 	bool
 	select ISA_DMA_API
 
+config ARCH_NO_VIRT_TO_BUS
+	def_bool y
+	depends on !ARCH_RPC && !ARCH_NETWINDER && !ARCH_SHARK
+
 # Select ISA DMA interface
 config ISA_DMA_API
 	bool
diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
index 80e29c605d4..4801717566d 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@@ -324,8 +324,6 @@
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x4000>;
 				interrupts = <5 4 5>;
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
 				status = "disabled";
@@ -335,8 +333,6 @@
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x4000>;
 				interrupts = <6 4 5>;
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
 				status = "disabled";
@@ -346,8 +342,6 @@
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x4000>;
 				interrupts = <7 4 5>;
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
 				status = "disabled";
@@ -357,8 +351,6 @@
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8028000 0x4000>;
 				interrupts = <8 4 5>;
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart3>;
 				status = "disabled";
diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index 8ecca6948d8..d112c3af8ce 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -197,9 +197,9 @@
 				};
 
 				usart3 {
-					pinctrl_uart3: usart3-0 {
+					pinctrl_usart3: usart3-0 {
 						atmel,pins =
-							<2 23 0x2 0x1	/* PC22 periph B with pullup */
+							<2 22 0x2 0x1	/* PC22 periph B with pullup */
 							 2 23 0x2 0x0>;	/* PC23 periph B */
 					};
 
@@ -402,8 +402,6 @@
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x200>;
 				interrupts = <5 4 5>;
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
 				status = "disabled";
@@ -413,8 +411,6 @@
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x200>;
 				interrupts = <6 4 5>;
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
 				status = "disabled";
@@ -424,8 +420,6 @@
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x200>;
 				interrupts = <7 4 5>;
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
 				status = "disabled";
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi
index 42eac1ff3cc..740630f9cd6 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/dove.dtsi
@@ -93,6 +93,7 @@
 			reg = <0xd0400 0x20>;
 			ngpios = <32>;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <12>, <13>, <14>, <60>;
 		};
 
@@ -103,6 +104,7 @@
 			reg = <0xd0420 0x20>;
 			ngpios = <32>;
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupts = <61>;
 		};
 
diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index e31bfc4a6f0..2feffc70814 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -48,13 +48,13 @@
 	};
 
 	pinctrl_0: pinctrl@11400000 {
-		compatible = "samsung,pinctrl-exynos4210";
+		compatible = "samsung,exynos4210-pinctrl";
 		reg = <0x11400000 0x1000>;
 		interrupts = <0 47 0>;
 	};
 
 	pinctrl_1: pinctrl@11000000 {
-		compatible = "samsung,pinctrl-exynos4210";
+		compatible = "samsung,exynos4210-pinctrl";
 		reg = <0x11000000 0x1000>;
 		interrupts = <0 46 0>;
 
@@ -66,7 +66,7 @@
 	};
 
 	pinctrl_2: pinctrl@03860000 {
-		compatible = "samsung,pinctrl-exynos4210";
+		compatible = "samsung,exynos4210-pinctrl";
 		reg = <0x03860000 0x1000>;
 	};
 
diff --git a/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi b/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi
index 8e6115adcd9..099cec79e2a 100644
--- a/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos4x12-pinctrl.dtsi
@@ -661,7 +661,7 @@
 
 		sd4_bus8: sd4-bus-width8 {
 			samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
-			samsung,pin-function = <3>;
+			samsung,pin-function = <4>;
 			samsung,pin-pud = <4>;
 			samsung,pin-drv = <3>;
 		};
diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi
index 179a62e46c9..9a878069490 100644
--- a/arch/arm/boot/dts/exynos4x12.dtsi
+++ b/arch/arm/boot/dts/exynos4x12.dtsi
@@ -37,13 +37,13 @@
 	};
 
 	pinctrl_0: pinctrl@11400000 {
-		compatible = "samsung,pinctrl-exynos4x12";
+		compatible = "samsung,exynos4x12-pinctrl";
 		reg = <0x11400000 0x1000>;
 		interrupts = <0 47 0>;
 	};
 
 	pinctrl_1: pinctrl@11000000 {
-		compatible = "samsung,pinctrl-exynos4x12";
+		compatible = "samsung,exynos4x12-pinctrl";
 		reg = <0x11000000 0x1000>;
 		interrupts = <0 46 0>;
 
@@ -55,14 +55,14 @@
 	};
 
 	pinctrl_2: pinctrl@03860000 {
-		compatible = "samsung,pinctrl-exynos4x12";
+		compatible = "samsung,exynos4x12-pinctrl";
 		reg = <0x03860000 0x1000>;
 		interrupt-parent = <&combiner>;
 		interrupts = <10 0>;
 	};
 
 	pinctrl_3: pinctrl@106E0000 {
-		compatible = "samsung,pinctrl-exynos4x12";
+		compatible = "samsung,exynos4x12-pinctrl";
 		reg = <0x106E0000 0x1000>;
 		interrupts = <0 72 0>;
 	};
diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi
index 024269de8ee..5f3562ad674 100644
--- a/arch/arm/boot/dts/exynos5440.dtsi
+++ b/arch/arm/boot/dts/exynos5440.dtsi
@@ -86,7 +86,7 @@
 	};
 
 	pinctrl {
-		compatible = "samsung,pinctrl-exynos5440";
+		compatible = "samsung,exynos5440-pinctrl";
 		reg = <0xE0000 0x1000>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
@@ -154,6 +154,6 @@
 	rtc {
 		compatible = "samsung,s3c6410-rtc";
 		reg = <0x130000 0x1000>;
-		interrupts = <0 16 0>, <0 17 0>;
+		interrupts = <0 17 0>, <0 16 0>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index d6265ca9711..ff1205ea571 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -866,7 +866,7 @@
 				compatible = "fsl,imx6q-fec";
 				reg = <0x02188000 0x4000>;
 				interrupts = <0 118 0x04 0 119 0x04>;
-				clocks = <&clks 117>, <&clks 117>, <&clks 177>;
+				clocks = <&clks 117>, <&clks 117>, <&clks 190>;
 				clock-names = "ipg", "ahb", "ptp";
 				status = "disabled";
 			};
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts b/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts
index a3d37ec2655..73187173117 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts
+++ b/arch/arm/boot/dts/vexpress-v2p-ca15-tc1.dts
@@ -70,7 +70,7 @@
 		compatible = "arm,sp805", "arm,primecell";
 		status = "disabled";
 		reg = <0 0x2b060000 0 0x1000>;
-		interrupts = <98>;
+		interrupts = <0 98 4>;
 		clocks = <&oscclk7>;
 		clock-names = "apb_pclk";
 	};
diff --git a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
index cf8071ad22d..dfe371ec274 100644
--- a/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
+++ b/arch/arm/boot/dts/vexpress-v2p-ca15_a7.dts
@@ -72,7 +72,7 @@
 	wdt@2a490000 {
 		compatible = "arm,sp805", "arm,primecell";
 		reg = <0 0x2a490000 0 0x1000>;
-		interrupts = <98>;
+		interrupts = <0 98 4>;
 		clocks = <&oscclk6a>, <&oscclk6a>;
 		clock-names = "wdogclk", "apb_pclk";
 	};
diff --git a/arch/arm/configs/marzen_defconfig b/arch/arm/configs/marzen_defconfig
index 728a43c446f..afb17d630d4 100644
--- a/arch/arm/configs/marzen_defconfig
+++ b/arch/arm/configs/marzen_defconfig
@@ -83,7 +83,6 @@ CONFIG_USB=y
 CONFIG_USB_RCAR_PHY=y
 CONFIG_MMC=y
 CONFIG_MMC_SDHI=y
-CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_OHCI_HCD_PLATFORM=y
diff --git a/arch/arm/configs/mvebu_defconfig b/arch/arm/configs/mvebu_defconfig
index b5bc96cb65a..cbd91bce1ca 100644
--- a/arch/arm/configs/mvebu_defconfig
+++ b/arch/arm/configs/mvebu_defconfig
@@ -33,6 +33,8 @@ CONFIG_MVNETA=y
 CONFIG_MARVELL_PHY=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
+CONFIG_I2C=y
+CONFIG_I2C_MV64XXX=y
 CONFIG_SERIAL_8250_DW=y
 CONFIG_GPIOLIB=y
 CONFIG_GPIO_SYSFS=y
diff --git a/arch/arm/configs/shark_defconfig b/arch/arm/configs/shark_defconfig
index caa07db90cf..e319b2c56f1 100644
--- a/arch/arm/configs/shark_defconfig
+++ b/arch/arm/configs/shark_defconfig
@@ -73,7 +73,6 @@ CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_CODEPAGE_850=m
 CONFIG_NLS_ISO8859_1=m
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
 # CONFIG_ENABLE_MUST_CHECK is not set
 CONFIG_DEBUG_KERNEL=y
 # CONFIG_SCHED_DEBUG is not set
diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig
index 231dca60473..426270fe080 100644
--- a/arch/arm/configs/u8500_defconfig
+++ b/arch/arm/configs/u8500_defconfig
@@ -66,9 +66,9 @@ CONFIG_SPI=y
 CONFIG_SPI_PL022=y
 CONFIG_GPIO_STMPE=y
 CONFIG_GPIO_TC3589X=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_AB8500_BM=y
-CONFIG_AB8500_BATTERY_THERM_ON_BATCTRL=y
+# CONFIG_POWER_SUPPLY is not set
+# CONFIG_AB8500_BM is not set
+# CONFIG_AB8500_BATTERY_THERM_ON_BATCTRL is not set
 CONFIG_THERMAL=y
 CONFIG_CPU_THERMAL=y
 CONFIG_MFD_STMPE=y
diff --git a/arch/arm/include/asm/dma.h b/arch/arm/include/asm/dma.h
index 5694a0d6576..58b8c6a0ab1 100644
--- a/arch/arm/include/asm/dma.h
+++ b/arch/arm/include/asm/dma.h
@@ -105,7 +105,7 @@ extern void set_dma_sg(unsigned int chan, struct scatterlist *sg, int nr_sg);
  */
 extern void __set_dma_addr(unsigned int chan, void *addr);
 #define set_dma_addr(chan, addr)				\
-	__set_dma_addr(chan, bus_to_virt(addr))
+	__set_dma_addr(chan, (void *)__bus_to_virt(addr))
 
 /* Set the DMA byte count for this channel
  *
diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h
index 64c770d2419..57870ab313c 100644
--- a/arch/arm/include/asm/memory.h
+++ b/arch/arm/include/asm/memory.h
@@ -245,6 +245,7 @@ static inline void *phys_to_virt(phys_addr_t x)
 #define __bus_to_pfn