Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (67 commits)
  cxgb4vf: recover from failure in cxgb4vf_open()
  netfilter: ebtables: make broute table work again
  netfilter: fix race in conntrack between dump_table and destroy
  ah: reload pointers to skb data after calling skb_cow_data()
  ah: update maximum truncated ICV length
  xfrm: check trunc_len in XFRMA_ALG_AUTH_TRUNC
  ehea: Increase the skb array usage
  net/fec: remove config FEC2 as it's used nowhere
  pcnet_cs: add new_id
  tcp: disallow bind() to reuse addr/port
  net/r8169: Update the function of parsing firmware
  net: ppp: use {get,put}_unaligned_be{16,32}
  CAIF: Fix IPv6 support in receive path for GPRS/3G
  arp: allow to invalidate specific ARP entries
  net_sched: factorize qdisc stats handling
  mlx4: Call alloc_etherdev to allocate RX and TX queues
  net: Add alloc_netdev_mqs function
  caif: don't set connection request param size before copying data
  cxgb4vf: fix mailbox data/control coherency domain race
  qlcnic: change module parameter permissions
  ...

109 files changed, 2901 insertions, 1867 deletions

diff --git a/Documentation/networking/dccp.txt b/Documentation/networking/dccp.txt
index b395ca6a49f..811872b45be 100644
--- a/Documentation/networking/dccp.txt
+++ b/Documentation/networking/dccp.txt
@@ -167,6 +167,7 @@ rx_ccid = 2
 seq_window = 100
 	The initial sequence window (sec. 7.5.2) of the sender. This influences
 	the local ackno validity and the remote seqno validity windows (7.5.1).
+	Values in the range Wmin = 32 (RFC 4340, 7.5.2) up to 2^32-1 can be set.
 
 tx_qlen = 5
 	The size of the transmit buffer in packets. A value of 0 corresponds
diff --git a/drivers/atm/ambassador.c b/drivers/atm/ambassador.c
index ffe9b655292..9f47e862526 100644
--- a/drivers/atm/ambassador.c
+++ b/drivers/atm/ambassador.c
@@ -1926,8 +1926,9 @@ static int __devinit ucode_init (loader_block * lb, amb_dev * dev) {
   const struct firmware *fw;
   unsigned long start_address;
   const struct ihex_binrec *rec;
+  const char *errmsg = 0;
   int res;
-  
+
   res = request_ihex_firmware(&fw, "atmsar11.fw", &dev->pci_dev->dev);
   if (res) {
     PRINTK (KERN_ERR, "Cannot load microcode data");
@@ -1937,8 +1938,8 @@ static int __devinit ucode_init (loader_block * lb, amb_dev * dev) {
   /* First record contains just the start address */
   rec = (const struct ihex_binrec *)fw->data;
   if (be16_to_cpu(rec->len) != sizeof(__be32) || be32_to_cpu(rec->addr)) {
-    PRINTK (KERN_ERR, "Bad microcode data (no start record)");
-    return -EINVAL;
+    errmsg = "no start record";
+    goto fail;
   }
   start_address = be32_to_cpup((__be32 *)rec->data);
 
@@ -1950,12 +1951,12 @@ static int __devinit ucode_init (loader_block * lb, amb_dev * dev) {
     PRINTD (DBG_LOAD, "starting region (%x, %u)", be32_to_cpu(rec->addr),
 	    be16_to_cpu(rec->len));
     if (be16_to_cpu(rec->len) > 4 * MAX_TRANSFER_DATA) {
-	    PRINTK (KERN_ERR, "Bad microcode data (record too long)");
-	    return -EINVAL;
+	    errmsg = "record too long";
+	    goto fail;
     }
     if (be16_to_cpu(rec->len) & 3) {
-	    PRINTK (KERN_ERR, "Bad microcode data (odd number of bytes)");
-	    return -EINVAL;
+	    errmsg = "odd number of bytes";
+	    goto fail;
     }
     res = loader_write(lb, dev, rec);
     if (res)
@@ -1970,6 +1971,10 @@ static int __devinit ucode_init (loader_block * lb, amb_dev * dev) {
     res = loader_start(lb, dev, start_address);
 
   return res;
+fail:
+  release_firmware(fw);
+  PRINTK(KERN_ERR, "Bad microcode data (%s)", errmsg);
+  return -EINVAL;
 }
 
 /********** give adapter parameters **********/
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 3fda24a28d2..ff652c77a0a 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -1944,19 +1944,12 @@ config 68360_ENET
 config FEC
 	bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
 	depends on M523x || M527x || M5272 || M528x || M520x || M532x || \
-		MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5
+		MACH_MX27 || ARCH_MX35 || ARCH_MX25 || ARCH_MX5 || SOC_IMX28
 	select PHYLIB
 	help
 	  Say Y here if you want to use the built-in 10/100 Fast ethernet
 	  controller on some Motorola ColdFire and Freescale i.MX processors.
 
-config FEC2
-	bool "Second FEC ethernet controller (on some ColdFire CPUs)"
-	depends on FEC
-	help
-	  Say Y here if you want to use the second built-in 10/100 Fast
-	  ethernet controller on some Motorola ColdFire processors.
-
 config FEC_MPC52xx
 	tristate "MPC52xx FEC driver"
 	depends on PPC_MPC52xx && PPC_BESTCOMM
diff --git a/drivers/net/bfin_mac.c b/drivers/net/bfin_mac.c
index ce1e5e9d06f..0b9fc5173ae 100644
--- a/drivers/net/bfin_mac.c
+++ b/drivers/net/bfin_mac.c
@@ -8,6 +8,11 @@
  * Licensed under the GPL-2 or later.
  */
 
+#define DRV_VERSION	"1.1"
+#define DRV_DESC	"Blackfin on-chip Ethernet MAC driver"
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
@@ -41,12 +46,7 @@
 
 #include "bfin_mac.h"
 
-#define DRV_NAME	"bfin_mac"
-#define DRV_VERSION	"1.1"
-#define DRV_AUTHOR	"Bryan Wu, Luke Yang"
-#define DRV_DESC	"Blackfin on-chip Ethernet MAC driver"
-
-MODULE_AUTHOR(DRV_AUTHOR);
+MODULE_AUTHOR("Bryan Wu, Luke Yang");
 MODULE_LICENSE("GPL");
 MODULE_DESCRIPTION(DRV_DESC);
 MODULE_ALIAS("platform:bfin_mac");
@@ -189,8 +189,7 @@ static int desc_list_init(void)
 		/* allocate a new skb for next time receive */
 		new_skb = dev_alloc_skb(PKT_BUF_SZ + NET_IP_ALIGN);
 		if (!new_skb) {
-			printk(KERN_NOTICE DRV_NAME
-			       ": init: low on mem - packet dropped\n");
+			pr_notice("init: low on mem - packet dropped\n");
 			goto init_error;
 		}
 		skb_reserve(new_skb, NET_IP_ALIGN);
@@ -240,7 +239,7 @@ static int desc_list_init(void)
 
 init_error:
 	desc_list_free();
-	printk(KERN_ERR DRV_NAME ": kmalloc failed\n");
+	pr_err("kmalloc failed\n");
 	return -ENOMEM;
 }
 
@@ -259,8 +258,7 @@ static int bfin_mdio_poll(void)
 	while ((bfin_read_EMAC_STAADD()) & STABUSY) {
 		udelay(1);
 		if (timeout_cnt-- < 0) {
-			printk(KERN_ERR DRV_NAME
-			": wait MDC/MDIO transaction to complete timeout\n");
+			pr_err("wait MDC/MDIO transaction to complete timeout\n");
 			return -ETIMEDOUT;
 		}
 	}
@@ -350,9 +348,9 @@ static void bfin_mac_adjust_link(struct net_device *dev)
 					opmode &= ~RMII_10;
 					break;
 				default:
-					printk(KERN_WARNING
-						"%s: Ack!  Speed (%d) is not 10/100!\n",
-						DRV_NAME, phydev->speed);
+					netdev_warn(dev,
+						"Ack! Speed (%d) is not 10/100!\n",
+						phydev->speed);
 					break;
 				}
 				bfin_write_EMAC_OPMODE(opmode);
@@ -417,14 +415,13 @@ static int mii_probe(struct net_device *dev, int phy_mode)
 
 	/* now we are supposed to have a proper phydev, to attach to... */
 	if (!phydev) {
-		printk(KERN_INFO "%s: Don't found any phy device at all\n",
-			dev->name);
+		netdev_err(dev, "no phy device found\n");
 		return -ENODEV;
 	}
 
 	if (phy_mode != PHY_INTERFACE_MODE_RMII &&
 		phy_mode != PHY_INTERFACE_MODE_MII) {
-		printk(KERN_INFO "%s: Invalid phy interface mode\n", dev->name);
+		netdev_err(dev, "invalid phy interface mode\n");
 		return -EINVAL;
 	}
 
@@ -432,7 +429,7 @@ static int mii_probe(struct net_device *dev, int phy_mode)
 			0, phy_mode);
 
 	if (IS_ERR(phydev)) {
-		printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
+		netdev_err(dev, "could not attach PHY\n");
 		return PTR_ERR(phydev);
 	}
 
@@ -453,11 +450,10 @@ static int mii_probe(struct net_device *dev, int phy_mode)
 	lp->old_duplex = -1;
 	lp->phydev = phydev;
 
-	printk(KERN_INFO "%s: attached PHY driver [%s] "
-	       "(mii_bus:phy_addr=%s, irq=%d, mdc_clk=%dHz(mdc_div=%d)"
-	       "@sclk=%dMHz)\n",
-	       DRV_NAME, phydev->drv->name, dev_name(&phydev->dev), phydev->irq,
-	       MDC_CLK, mdc_div, sclk/1000000);
+	pr_info("attached PHY driver [%s] "
+	        "(mii_bus:phy_addr=%s, irq=%d, mdc_clk=%dHz(mdc_div=%d)@sclk=%dMHz)\n",
+	        phydev->drv->name, dev_name(&phydev->dev), phydev->irq,
+	        MDC_CLK, mdc_div, sclk/1000000);
 
 	return 0;
 }
@@ -502,7 +498,7 @@ bfin_mac_ethtool_setsettings(struct net_device *dev, struct ethtool_cmd *cmd)
 static void bfin_mac_ethtool_getdrvinfo(struct net_device *dev,
 					struct ethtool_drvinfo *info)
 {
-	strcpy(info->driver, DRV_NAME);
+	strcpy(info->driver, KBUILD_MODNAME);
 	strcpy(info->version, DRV_VERSION);
 	strcpy(info->fw_version, "N/A");
 	strcpy(info->bus_info, dev_name(&dev->dev));