diff options
| author | Jon Povey <jon.povey@racelogic.co.uk> | 2010-10-12 13:47:05 +0900 |
|---|---|---|
| committer | Ben Dooks <ben-linux@fluff.org> | 2010-10-18 01:25:33 +0100 |
| commit | c5b4afec8e669bbe265daea24037fccfc42c4fe3 (patch) | |
| tree | dc711356af9d49180cca3806b93ee2fa7548befe | |
| parent | 85a331881dd52a93e7d4c57bcaf5486cc8718465 (diff) | |
i2c-davinci: Fix TX setup for more SoCs
This patch is an improvement to 4bba0fd8d1c6d405df666e2573e1a1f917098be0
which got to mainline a little early.
Sudhakar Rajashekhara explains that at least OMAP-L138 requires MDR mode
settings before DXR for correct behaviour, so load MDR first with
STT cleared and later load again with STT set.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
| -rw-r--r-- | drivers/i2c/busses/i2c-davinci.c | 24 |
1 files changed, 15 insertions, 9 deletions
diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c index b8feac5f2ef..5795c8398c7 100644 --- a/drivers/i2c/busses/i2c-davinci.c +++ b/drivers/i2c/busses/i2c-davinci.c @@ -331,21 +331,16 @@ i2c_davinci_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg, int stop) INIT_COMPLETION(dev->cmd_complete); dev->cmd_err = 0; - /* Take I2C out of reset, configure it as master and set the - * start bit */ - flag = DAVINCI_I2C_MDR_IRS | DAVINCI_I2C_MDR_MST | DAVINCI_I2C_MDR_STT; + /* Take I2C out of reset and configure it as master */ + flag = DAVINCI_I2C_MDR_IRS | DAVINCI_I2C_MDR_MST; /* if the slave address is ten bit address, enable XA bit */ if (msg->flags & I2C_M_TEN) flag |= DAVINCI_I2C_MDR_XA; if (!(msg->flags & I2C_M_RD)) flag |= DAVINCI_I2C_MDR_TRX; - if (stop) - flag |= DAVINCI_I2C_MDR_STP; - if (msg->len == 0) { + if (msg->len == 0) flag |= DAVINCI_I2C_MDR_RM; - flag &= ~DAVINCI_I2C_MDR_STP; - } /* Enable receive or transmit interrupts */ w = davinci_i2c_read_reg(dev, DAVINCI_I2C_IMR_REG); @@ -358,17 +353,28 @@ i2c_davinci_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg, int stop) dev->terminate = 0; /* + * Write mode register first as needed for correct behaviour + * on OMAP-L138, but don't set STT yet to avoid a race with XRDY + * occuring before we have loaded DXR + */ + davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, flag); + + /* * First byte should be set here, not after interrupt, * because transmit-data-ready interrupt can come before * NACK-interrupt during sending of previous message and * ICDXR may have wrong data + * It also saves us one interrupt, slightly faster */ if ((!(msg->flags & I2C_M_RD)) && dev->buf_len) { davinci_i2c_write_reg(dev, DAVINCI_I2C_DXR_REG, *dev->buf++); dev->buf_len--; } - /* write the data into mode register; start transmitting */ + /* Set STT to begin transmit now DXR is loaded */ + flag |= DAVINCI_I2C_MDR_STT; + if (stop && msg->len != 0) + flag |= DAVINCI_I2C_MDR_STP; davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, flag); r = wait_for_completion_interruptible_timeout(&dev->cmd_complete, |