Merge branch 'samsung/pinctrl' into next/dt2

* samsung/pinctrl:
  pinctrl: exynos: Fix wakeup IRQ domain registration check
  pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
  pinctrl: exynos: Correct the detection of wakeup-eint node
  pinctrl: exynos: Mark exynos_irq_demux_eint as inline
  pinctrl: exynos: Handle only unmasked wakeup interrupts
  pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
  pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
  ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
  ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
  ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
  gpio: exynos4: skip gpiolib registration if pinctrl driver is used
  pinctrl: add exynos4210 specific extensions for samsung pinctrl driver
  pinctrl: add samsung pinctrl and gpiolib driver

12 files changed, 2674 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
new file mode 100644
index 00000000000..03dee50532f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
@@ -0,0 +1,196 @@
+Samsung GPIO and Pin Mux/Config controller
+
+Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
+controller. It controls the input/output settings on the available pads/pins
+and also provides ability to multiplex and configure the output of various
+on-chip controllers onto these pads.
+
+Required Properties:
+- compatible: should be one of the following.
+  - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
+  - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
+
+- reg: Base address of the pin controller hardware module and length of
+  the address space it occupies.
+
+- interrupts: interrupt specifier for the controller. The format and value of
+  the interrupt specifier depends on the interrupt parent for the controller.
+
+- Pin mux/config groups as child nodes: The pin mux (selecting pin function
+  mode) and pin config (pull up/down, driver strength) settings are represented
+  as child nodes of the pin-controller node. There should be atleast one
+  child node and there is no limit on the count of these child nodes.
+
+  The child node should contain a list of pin(s) on which a particular pin
+  function selection or pin configuration (or both) have to applied. This
+  list of pins is specified using the property name "samsung,pins". There
+  should be atleast one pin specfied for this property and there is no upper
+  limit on the count of pins that can be specified. The pins are specified
+  using pin names which are derived from the hardware manual of the SoC. As
+  an example, the pins in GPA0 bank of the pin controller can be represented
+  as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
+  The format of the pin names should be (as per the hardware manual)
+  "[pin bank name]-[pin number within the bank]".
+
+  The pin function selection that should be applied on the pins listed in the
+  child node is specified using the "samsung,pin-function" property. The value
+  of this property that should be applied to each of the pins listed in the
+  "samsung,pins" property should be picked from the hardware manual of the SoC
+  for the specified pin group. This property is optional in the child node if
+  no specific function selection is desired for the pins listed in the child
+  node. The value of this property is used as-is to program the pin-controller
+  function selector register of the pin-bank.
+
+  The child node can also optionally specify one or more of the pin
+  configuration that should be applied on all the pins listed in the
+  "samsung,pins" property of the child node. The following pin configuration
+  properties are supported.
+
+  - samsung,pin-pud: Pull up/down configuration.
+  - samsung,pin-drv: Drive strength configuration.
+  - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
+  - samsung,pin-drv-pdn: Drive strength configuration in power down mode.
+
+  The values specified by these config properties should be derived from the
+  hardware manual and these values are programmed as-is into the pin
+  pull up/down and driver strength register of the pin-controller.
+
+  Note: A child should include atleast a pin function selection property or
+  pin configuration property (one or more) or both.
+
+  The client nodes that require a particular pin function selection and/or
+  pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
+  file.
+
+External GPIO and Wakeup Interrupts:
+
+The controller supports two types of external interrupts over gpio. The first
+is the external gpio interrupt and second is the external wakeup interrupts.
+The difference between the two is that the external wakeup interrupts can be
+used as system wakeup events.
+
+A. External GPIO Interrupts: For supporting external gpio interrupts, the
+   following properties should be specified in the pin-controller device node.
+
+- interrupt-controller: identifies the controller node as interrupt-parent.
+- #interrupt-cells: the value of this property should be 2.
+  - First Cell: represents the external gpio interrupt number local to the
+    external gpio interrupt space of the controller.
+  - Second Cell: flags to identify the type of the interrupt
+    - 1 = rising edge triggered
+    - 2 = falling edge triggered
+    - 3 = rising and falling edge triggered
+    - 4 = high level triggered
+    - 8 = low level triggered
+
+B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
+   child node representing the external wakeup interrupt controller should be
+   included in the pin-controller device node. This child node should include
+   the following properties.
+
+   - compatible: identifies the type of the external wakeup interrupt controller
+     The possible values are:
+     - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung Exynos4210 SoC.
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     wakeup interrupts are forwarded to.
+   - interrupt-controller: identifies the node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2
+     - First Cell: represents the external wakeup interrupt number local to
+       the external wakeup interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+
+Aliases:
+
+All the pin controller nodes should be represented in the aliases node using
+the following format 'pinctrl{n}' where n is a unique number for the alias.
+
+Example 1: A pin-controller node with pin groups.
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		uart0_data: uart0-data {
+			samsung,pins = "gpa0-0", "gpa0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart0_fctl: uart0-fctl {
+			samsung,pins = "gpa0-2", "gpa0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_data: uart1-data {
+			samsung,pins = "gpa0-4", "gpa0-5";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_fctl: uart1-fctl {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c2_bus: i2c2-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+Example 2: A pin-controller node with external wakeup interrupt controller node.
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
+					<0 32 0>;
+		};
+	};
+
+Example 3: A uart client node that supports 'default' and 'flow-control' states.
+
+	uart@13800000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13800000 0x100>;
+		interrupts = <0 52 0>;
+		pinctrl-names = "default", "flow-control;
+		pinctrl-0 = <&uart0_data>;
+		pinctrl-1 = <&uart0_data &uart0_fctl>;
+	};
+
+Example 4: Set up the default pin state for uart controller.
+
+	static int s3c24xx_serial_probe(struct platform_device *pdev) {
+		struct pinctrl *pinctrl;
+		...
+		...
+		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
+	}
diff --git a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
new file mode 100644
index 00000000000..b12cf272ad0
--- /dev/null
+++ b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
@@ -0,0 +1,457 @@
+/*
+ * Samsung's Exynos4210 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2011-2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2011-2012 Linaro Ltd.
+ *		www.linaro.org
+ *
+ * Samsung's Exynos4210 SoC pin-mux and pin-config optiosn are listed as device
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/ {
+	pinctrl@11400000 {
+		uart0_data: uart0-data {
+			samsung,pins = "gpa0-0", "gpa0-1";
+			samsung,pin-function = <0x2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart0_fctl: uart0-fctl {
+			samsung,pins = "gpa0-2", "gpa0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_data: uart1-data {
+			samsung,pins = "gpa0-4", "gpa0-5";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_fctl: uart1-fctl {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c2_bus: i2c2-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart2_data: uart2-data {
+			samsung,pins = "gpa1-0", "gpa1-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart2_fctl: uart2-fctl {
+			samsung,pins = "gpa1-2", "gpa1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart_audio_a: uart-audio-a {
+			samsung,pins = "gpa1-0", "gpa1-1";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c3_bus: i2c3-bus {
+			samsung,pins = "gpa1-2", "gpa1-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart3_data: uart3-data {
+			samsung,pins = "gpa1-4", "gpa1-5";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart_audio_b: uart-audio-b {
+			samsung,pins = "gpa1-4", "gpa1-5";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		spi0_bus: spi0-bus {
+			samsung,pins = "gpb-0", "gpb-2", "gpb-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c4_bus: i2c4-bus {
+			samsung,pins = "gpb-2", "gpb-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		spi1_bus: spi1-bus {
+			samsung,pins = "gpb-4", "gpb-6", "gpb-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c5_bus: i2c5-bus {
+			samsung,pins = "gpb-6", "gpb-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2s1_bus: i2s1-bus {
+			samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+					"gpc0-4";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pcm1_bus: pcm1-bus {
+			samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+					"gpc0-4";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		ac97_bus: ac97-bus {
+			samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+					"gpc0-4";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2s2_bus: i2s2-bus {
+			samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+					"gpc1-4";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pcm2_bus: pcm2-bus {
+			samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+					"gpc1-4";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		spdif_bus: spdif-bus {
+			samsung,pins = "gpc1-0", "gpc1-1";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c6_bus: i2c6-bus {
+			samsung,pins = "gpc1-3", "gpc1-4";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		spi2_bus: spi2-bus {
+			samsung,pins = "gpc1-1", "gpc1-2", "gpc1-3", "gpc1-4";
+			samsung,pin-function = <5>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c7_bus: i2c7-bus {
+			samsung,pins = "gpd0-2", "gpd0-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c0_bus: i2c0-bus {
+			samsung,pins = "gpd1-0", "gpd1-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c1_bus: i2c1-bus {
+			samsung,pins = "gpd1-2", "gpd1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+	pinctrl@11000000 {
+		sd0_clk: sd0-clk {
+			samsung,pins = "gpk0-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd0_cmd: sd0-cmd {
+			samsung,pins = "gpk0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd0_cd: sd0-cd {
+			samsung,pins = "gpk0-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd0_bus1: sd0-bus-width1 {
+			samsung,pins = "gpk0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd0_bus4: sd0-bus-width4 {
+			samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd0_bus8: sd0-bus-width8 {
+			samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_clk: sd4-clk {
+			samsung,pins = "gpk0-0";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_cmd: sd4-cmd {
+			samsung,pins = "gpk0-1";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_cd: sd4-cd {
+			samsung,pins = "gpk0-2";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_bus1: sd4-bus-width1 {
+			samsung,pins = "gpk0-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_bus4: sd4-bus-width4 {
+			samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_bus8: sd4-bus-width8 {
+			samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <4>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd1_clk: sd1-clk {
+			samsung,pins = "gpk1-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd1_cmd: sd1-cmd {
+			samsung,pins = "gpk1-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd1_cd: sd1-cd {
+			samsung,pins = "gpk1-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd1_bus1: sd1-bus-width1 {
+			samsung,pins = "gpk1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd1_bus4: sd1-bus-width4 {
+			samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_clk: sd2-clk {
+			samsung,pins = "gpk2-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_cmd: sd2-cmd {
+			samsung,pins = "gpk2-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_cd: sd2-cd {
+			samsung,pins = "gpk2-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_bus1: sd2-bus-width1 {
+			samsung,pins = "gpk2-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_bus4: sd2-bus-width4 {
+			samsung,pins = "gpk2-3", "gpk2-4", "gpk2-5", "gpk2-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_bus8: sd2-bus-width8 {
+			samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_clk: sd3-clk {
+			samsung,pins = "gpk3-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_cmd: sd3-cmd {
+			samsung,pins = "gpk3-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_cd: sd3-cd {
+			samsung,pins = "gpk3-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_bus1: sd3-bus-width1 {
+			samsung,pins = "gpk3-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_bus4: sd3-bus-width4 {
+			samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		eint0: ext-int0 {
+			samsung,pins = "gpx0-0";
+			samsung,pin-function = <0xf>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		eint8: ext-int8 {
+			samsung,pins = "gpx1-0";
+			samsung,pin-function = <0xf>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		eint15: ext-int15 {
+			samsung,pins = "gpx1-7";
+			samsung,pin-function = <0xf>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		eint16: ext-int16 {
+			samsung,pins = "gpx2-0";
+			samsung,pin-function = <0xf>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		eint31: ext-int31 {
+			samsung,pins = "gpx3-7";
+			samsung,pin-function = <0xf>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+	pinctrl@03860000 {
+		i2s0_bus: i2s0-bus {
+			samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
+					"gpz-4", "gpz-5", "gpz-6";
+			samsung,pin-function = <0x2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pcm0_bus: pcm0-bus {
+			samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
+					"gpz-4";
+			samsung,pin-function = <0x3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index 02891fe876e..a4bd0c9a206 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -20,6 +20,7 @@
 */
 
 /include/ "skeleton.dtsi"
+/include/ "exynos4210-pinctrl.dtsi"
 
 / {
 	compatible = "samsung,exynos4210";
@@ -29,6 +30,9 @@
 		spi0 = &spi_0;
 		spi1 = &spi_1;
 		spi2 = &spi_2;
+		pinctrl0 = &pinctrl_0;
+		pinctrl1 = &pinctrl_1;
+		pinctrl2 = &pinctrl_2;
 	};
 
 	gic:interrupt-controller@10490000 {
@@ -50,6 +54,39 @@
 			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
 	};
 
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
+					<0 32 0>;
+		};
+	};
+
+	pinctrl_2: pinctrl@03860000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x03860000 0x1000>;
+	};
+
 	watchdog@10060000 {
 		compatible = "samsung,s3c2410-wdt";
 		reg = <0x10060000 0x100>;
diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index 7ec64c8c991..9abdd5747c2 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -408,6 +408,8 @@ config MACH_EXYNOS4_DT
 	select USE_OF
 	select ARM_AMBA
 	select HAVE_SAMSUNG_KEYPAD if INPUT_KEYBOARD
+	select PINCTRL
+	select PINCTRL_EXYNOS4
 	help
 	  Machine support for Samsung Exynos4 machine with device tree enabled.
 	  Select this if a fdt blob is available for the Exynos4 SoC based board.
diff --git a/arch/arm/mach-exynos/common.c b/arch/arm/mach-exynos/common.c
index 4eb39cdf75e..715b690e500 100644
--- a/arch/arm/mach-exynos/common.c
+++ b/arch/arm/mach-exynos/common.c
@@ -980,6 +980,32 @@ static int __init exynos_init_irq_eint(void)
 {
 	int irq;
 
+#ifdef CONFIG_PINCTRL_SAMSUNG
+	/*
+	 * The Samsung pinctrl driver provides an integrated gpio/pinmux/pinconf
+	 * functionality along with support for external gpio and wakeup
+	 * interrupts. If the samsung pinctrl driver is enabled and includes
+	 * the wakeup interrupt support, then the setting up external wakeup
+	 * interrupts here can be skipped. This check here is temporary to
+	 * allow exynos4 platforms that do not use Samsung pinctrl driver to
+	 * co-exist with platforms that do. When all of the Samsung Exynos4
+	 * platforms switch over to using the pinctrl driver, the wakeup
+	 * interrupt support code here can be completely removed.
+	 */
+	struct device_node *pctrl_np, *wkup_np;
+	const char *pctrl_compat = "samsung,pinctrl-exynos4210";
+	const char *wkup_compat = "samsung,exynos4210-wakeup-eint";
+
+	for_each_compatible_node(pctrl_np, NULL, pctrl_compat) {
+		if (of_device_is_available(pctrl_np)) {
+			wkup_np = of_find_compatible_node(pctrl_np, NULL,
+							wkup_compat);
+			if (wkup_np)
+				return -ENODEV;
+		}
+	}
+#endif
+
 	if (soc_is_exynos5250())
 		exynos_eint_base = ioremap(EXYNOS5_PA_GPIO1, SZ_4K);
 	else
diff --git a/drivers/gpio/gpio-samsung.c b/drivers/gpio/gpio-samsung.c
index ba126cc0407..41ab7f66cdf 100644
--- a/drivers/gpio/gpio-samsung.c
+++ b/drivers/gpio/gpio-samsung.c
@@ -2734,6 +2734,27 @@ static __init void exynos4_gpiolib_init(void)
 	int group = 0;
 	void __iomem *gpx_base;
 
+#ifdef CONFIG_PINCTRL_SAMSUNG
+		/*
+		 * This gpio driver includes support for device tree support and
+		 * there are platforms using it. In order to maintain
+		 * compatibility with those platforms, and to allow non-dt
+		 * Exynos4210 platforms to use this gpiolib support, a check
+		 * is added to find out if there is a active pin-controller
+		 * driver support available. If it is available, this gpiolib
+		 * support is ignored and the gpiolib support available in
+		 * pin-controller driver is used. This is a temporary check and
+		 * will go away when all of the Exynos4210 platforms have
+		 * switched to using device tree and the pin-ctrl driver.
+		 */
+		struct device_node *pctrl_np;
+		const char *pctrl_compat = "samsung,pinctrl-exynos4210";
+		pctrl_np = of_find_compatible_node(NULL, NULL, pctrl_compat);
+		if (pctrl_np)
+			if (of_device_is_available(pctrl_np))
+				return;
+#endif
+
 	/* gpio part1 */
 	gpio_base1 = ioremap(EXYNOS4_PA_GPIO1, SZ_4K);
 	if (gpio_base1 == NULL) {
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index 54e3588bef6..34e94c7f68c 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -145,6 +145,15 @@ config PINCTRL_COH901
 	  COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
 	  ports of 8 GPIO pins each.
 
+config PINCTRL_SAMSUNG
+	bool "Samsung pinctrl driver"
+	select PINMUX
+	select PINCONF
+
+config PINCTRL_EXYNOS4
+	bool "Pinctrl driver data for Exynos4 SoC"
+	select PINCTRL_SAMSUNG
+
 source "drivers/pinctrl/spear/Kconfig"
 
 endmenu
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index f40b1f81ff2..6a88113e11d 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -29,5 +29,7 @@ obj-$(CONFIG_PINCTRL_TEGRA20)	+= pinctrl-tegra20.o
 obj-$(CONFIG_PINCTRL_TEGRA30)	+= pinctrl-tegra30.o
 obj-$(CONFIG_PINCTRL_U300)	+= pinctrl-u300.o
 obj-$(CONFIG_PINCTRL_COH901)	+= pinctrl-coh901.o
+obj-$(CONFIG_PINCTRL_SAMSUNG)	+= pinctrl-samsung.o
+obj-$(CONFIG_PINCTRL_EXYNOS4)	+= pinctrl-exynos.o
 
 obj-$(CONFIG_PLAT_SPEAR)	+= spear/
diff --git a/drivers/pinctrl/pinctrl-exynos.c b/drivers/pinctrl/pinctrl-exynos.c
new file mode 100644
index 00000000000..21362f48d37
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-exynos.c
@@ -0,0 +1,579 @@
+/*
+ * Exynos specific support for Samsung pinctrl/gpiolib driver with eint support.
+ *
+ * Copyright (c) 2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2012 Linaro Ltd
+ *		http://www.linaro.org
+ *
+ * Author: Thomas Abraham <thomas.ab@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This file contains the Samsung Exynos specific information required by the
+ * the Samsung pinctrl/gpiolib driver. It also includes the implementation of
+ * external gpio and wakeup interrupt support.
+ */
+
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/irqdomain.h>
+#include <linux/irq.h>
+#include <linux/of_irq.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+
+#include <asm/mach/irq.h>
+
+#include "pinctrl-samsung.h"
+#include "pinctrl-exynos.h"
+
+/* list of external wakeup controllers supported */
+static const struct of_device_id exynos_wkup_irq_ids[] = {
+	{ .compatible = "samsung,exynos4210-wakeup-eint", },
+};
+
+static void exynos_gpio_irq_unmask(struct irq_data *irqd)
+{
+	struct samsung_pinctrl_drv_data *d = irqd->domain->host_data;
+	struct exynos_geint_data *edata = irq_data_get_irq_handler_data(irqd);
+	unsigned long reg_mask = d->ctrl->geint_mask + edata->eint_offset;
+	unsigned long mask;
+
+	mask = readl(d->virt_base + reg_mask);
+	mask &= ~(1 << edata->pin);
+	writel(mask, d->virt_base + reg_mask);
+}
+
+static void exynos_gpio_irq_mask(struct irq_data *irqd)
+{
+	struct samsung_pinctrl_drv_data *d = irqd->domain->host_data;
+	struct exynos_geint_data *edata = irq_data_get_irq_handler_data(irqd);
+	unsigned long reg_mask = d->ctrl->geint_mask + edata->eint_offset;
+	unsigned long mask;
+
+	mask = readl(d->virt_base + reg_mask);
+	mask |= 1 << edata->pin;
+	writel(mask, d->virt_base + reg_mask);
+}
+
+static void exynos_gpio_irq_ack(struct irq_data *irqd)
+{
+	struct samsung_pinctrl_drv_data *d = irqd->domain->host_data;
+	struct exynos_geint_data *edata = irq_data_get_irq_handler_data(irqd);
+	unsigned long reg_pend = d->ctrl->geint_pend + edata->eint_offset;
+
+	writel(1 << edata->pin, d->virt_base + reg_pend);
+}
+
+static int exynos_gpio_irq_set_type(struct irq_data *irqd, unsigned int type)
+{
+	struct samsung_pinctrl_drv_data *d = irqd->domain->host_data;
+	struct samsung_pin_ctrl *ctrl = d->ctrl;
+	struct exynos_geint_data *edata = irq_data_get_irq_handler_data(irqd);
+	struct samsung_pin_bank *bank = edata->bank;
+	unsigned int shift = EXYNOS_EINT_CON_LEN * edata->pin;
+	unsigned int con, trig_type;
+	unsigned long reg_con = ctrl->geint_con + edata->eint_offset;
+	unsigned int mask;
+
+	switch (type) {
+	case IRQ_TYPE_EDGE_RISING:
+		trig_type = EXYNOS_EINT_EDGE_RISING;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		trig_type = EXYNOS_EINT_EDGE_FALLING;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		trig_type = EXYNOS_EINT_EDGE_BOTH;
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:
+		trig_type = EXYNOS_EINT_LEVEL_HIGH;
+		break;
+	case IRQ_TYPE_LEVEL_LOW:
+		trig_type = EXYNOS_EINT_LEVEL_LOW;
+		break;
+	default:
+		pr_err("unsupported external interrupt type\n");
+		return -EINVAL;
+	}
+
+	if (type & IRQ_TYPE_EDGE_BOTH)
+		__irq_set_handler_locked(irqd->irq, handle_edge_irq);
+	else
+		__irq_set_handler_locked(irqd->irq, handle_level_irq);
+
+	con = readl(d->virt_base + reg_con);
+	con &= ~(EXYNOS_EINT_CON_MASK << shift);
+	con |= trig_type << shift;
+	writel(con, d->virt_base + reg_con);
+
+	reg_con = bank->pctl_offset;
+	shift = edata->pin * bank->func_width;
+	mask = (1 << bank->func_width) - 1;
+
+	con = readl(d->virt_base + reg_con);
+	con &= ~(mask << shift);
+	con |= EXYNOS_EINT_FUNC << shift;
+	writel(con, d->virt_base + reg_con);
+
+	return 0;
+}
+
+/*
+ * irq_chip for gpio interrupts.
+ */
+static struct irq_c