hwmon/w83627ehf: Add support for the W83627DHG chip

Signed-off-by: David Hubbard <david.c.hubbard@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

2 files changed, 90 insertions, 18 deletions

diff --git a/Documentation/hwmon/w83627ehf b/Documentation/hwmon/w83627ehf
index 8a15a740875..030fac6cec7 100644
--- a/Documentation/hwmon/w83627ehf
+++ b/Documentation/hwmon/w83627ehf
@@ -2,26 +2,29 @@ Kernel driver w83627ehf
 =======================
 
 Supported chips:
-  * Winbond W83627EHF/EHG (ISA access ONLY)
+  * Winbond W83627EHF/EHG/DHG (ISA access ONLY)
     Prefix: 'w83627ehf'
     Addresses scanned: ISA address retrieved from Super I/O registers
-    Datasheet: http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83627EHF_%20W83627EHGb.pdf
+    Datasheet:
+        http://www.winbond-usa.com/products/winbond_products/pdfs/PCIC/W83627EHF_%20W83627EHGb.pdf
+        DHG datasheet confidential.
 
 Authors:
         Jean Delvare <khali@linux-fr.org>
         Yuan Mu (Winbond)
         Rudolf Marek <r.marek@assembler.cz>
+        David Hubbard <david.c.hubbard@gmail.com>
 
 Description
 -----------
 
-This driver implements support for the Winbond W83627EHF and W83627EHG
-super I/O chips. We will refer to them collectively as Winbond chips.
+This driver implements support for the Winbond W83627EHF, W83627EHG, and
+W83627DHG super I/O chips. We will refer to them collectively as Winbond chips.
 
 The chips implement three temperature sensors, five fan rotation
-speed sensors, ten analog voltage sensors, alarms with beep warnings (control
-unimplemented), and some automatic fan regulation strategies (plus manual
-fan control mode).
+speed sensors, ten analog voltage sensors (only nine for the 627DHG), alarms
+with beep warnings (control unimplemented), and some automatic fan regulation
+strategies (plus manual fan control mode).
 
 Temperatures are measured in degrees Celsius and measurement resolution is 1
 degC for temp1 and 0.5 degC for temp2 and temp3. An alarm is triggered when
@@ -55,6 +58,9 @@ prog  -> pwm4 (the programmable setting is not supported by the driver)
 /sys files
 ----------
 
+name - this is a standard hwmon device entry. For the W83627EHF and W83627EHG,
+       it is set to "w83627ehf" and for the W83627DHG it is set to "w83627dhg"
+
 pwm[1-4] - this file stores PWM duty cycle or DC value (fan speed) in range:
 	   0 (stop) to 255 (full)
 
@@ -83,3 +89,37 @@ pwm[1-4]_stop_time  - how many milliseconds [ms] must elapse to switch
 
 Note: last two functions are influenced by other control bits, not yet exported
       by the driver, so a change might not have any effect.
+
+Implementation Details
+----------------------
+
+Future driver development should bear in mind that the following registers have
+different functions on the 627EHF and the 627DHG. Some registers also have
+different power-on default values, but BIOS should already be loading
+appropriate defaults. Note that bank selection must be performed as is currently
+done in the driver for all register addresses.
+
+0x49:  only on DHG, selects temperature source for AUX fan, CPU fan0
+0x4a:  not completely documented for the EHF and the DHG documentation assigns
+       different behavior to bits 7 and 6, including extending the temperature
+       input selection to SmartFan I, not just SmartFan III. Testing on the EHF
+       will reveal whether they are compatible or not.
+
+0x58:  Chip ID: 0xa1=EHF 0xc1=DHG
+0x5e:  only on DHG, has bits to enable "current mode" temperature detection and
+       critical temperature protection
+0x45b: only on EHF, bit 3, vin4 alarm (EHF supports 10 inputs, only 9 on DHG)
+0x552: only on EHF, vin4
+0x558: only on EHF, vin4 high limit
+0x559: only on EHF, vin4 low limit
+0x6b:  only on DHG, SYS fan critical temperature
+0x6c:  only on DHG, CPU fan0 critical temperature
+0x6d:  only on DHG, AUX fan critical temperature
+0x6e:  only on DHG, CPU fan1 critical temperature
+
+0x50-0x55 and 0x650-0x657 are marked "Test Register" for the EHF, but "Reserved
+       Register" for the DHG
+
+The DHG also supports PECI, where the DHG queries Intel CPU temperatures, and
+the ICH8 southbridge gets that data via PECI from the DHG, so that the
+southbridge drives the fans. And the DHG supports SST, a one-wire serial bus.
diff --git a/drivers/hwmon/w83627ehf.c b/drivers/hwmon/w83627ehf.c
index 212a1558c63..da5828f2dfc 100644
--- a/drivers/hwmon/w83627ehf.c
+++ b/drivers/hwmon/w83627ehf.c
@@ -32,8 +32,10 @@
 
     Supports the following chips:
 
-    Chip        #vin    #fan    #pwm    #temp   chip_id    man_id
-    w83627ehf   10      5       4       3       0x88,0xa1  0x5ca3
+    Chip        #vin    #fan    #pwm    #temp  chip IDs       man ID
+    w83627ehf   10      5       4       3      0x8850 0x88    0x5ca3
+                                               0x8860 0xa1
+    w83627dhg    9      5       4       3      0xa020 0xc1    0x5ca3
 */
 
 #include <linux/module.h>
@@ -55,8 +57,18 @@ static unsigned short address;
  * Super-I/O constants and functions
  */
 
+/*
+ * The three following globals are initialized in w83627ehf_find(), before
+ * the i2c-isa device is created. Otherwise, they could be stored in
+ * w83627ehf_data. This is ugly, but necessary, and when the driver is next
+ * updated to become a platform driver, the globals will disappear.
+ */
 static int REG;		/* The register to read/write */
 static int VAL;		/* The value to read/write */
+/* The w83627ehf/ehg have 10 voltage inputs, but the w83627dhg has 9. This
+ * value is also used in w83627ehf_detect() to export a device name in sysfs
+ * (e.g. w83627ehf or w83627dhg) */
+static int w83627ehf_num_in;
 
 #define W83627EHF_LD_HWM	0x0b
 
@@ -65,8 +77,10 @@ static int VAL;		/* The value to read/write */
 #define SIO_REG_ENABLE		0x30	/* Logical device enable */
 #define SIO_REG_ADDR		0x60	/* Logical device address (2 bytes) */
 
-#define SIO_W83627EHF_ID	0x8840
-#define SIO_ID_MASK		0xFFC0
+#define SIO_W83627EHF_ID	0x8850
+#define SIO_W83627EHG_ID	0x8860
+#define SIO_W83627DHG_ID	0xa020
+#define SIO_ID_MASK		0xFFF0
 
 static inline void
 superio_outb(int reg, int val)
@@ -115,8 +129,12 @@ superio_exit(void)
 
 #define W83627EHF_REG_BANK		0x4E
 #define W83627EHF_REG_CONFIG		0x40
-#define W83627EHF_REG_CHIP_ID		0x49
-#define W83627EHF_REG_MAN_ID		0x4F
+
+/* Not currently used:
+ * REG_MAN_ID has the value 0x5ca3 for all supported chips.
+ * REG_CHIP_ID == 0x88/0xa1/0xc1 depending on chip model.
+ * REG_MAN_ID is at port 0x4f
+ * REG_CHIP_ID is at port 0x58 */
 
 static const u16 W83627EHF_REG_FAN[] = { 0x28, 0x29, 0x2a, 0x3f, 0x553 };
 static const u16 W83627EHF_REG_FAN_MIN[] = { 0x3b, 0x3c, 0x3d, 0x3e, 0x55c };
@@ -429,7 +447,7 @@ static struct w83627ehf_data *w83627ehf_update_device(struct device *dev)
 		}
 
 		/* Measured voltages and limits */
-		for (i = 0; i < 10; i++) {
+		for (i = 0; i < w83627ehf_num_in; i++) {
 			data->in[i] = w83627ehf_read_value(client,
 				      W83627EHF_REG_IN(i));
 			data->in_min[i] = w83627ehf_read_value(client,
@@ -1121,7 +1139,7 @@ static void w83627ehf_device_remove_files(struct device *dev)
 		device_remove_file(dev, &sda_sf3_arrays[i].dev_attr);
 	for (i = 0; i < ARRAY_SIZE(sda_sf3_arrays_fan4); i++)
 		device_remove_file(dev, &sda_sf3_arrays_fan4[i].dev_attr);
-	for (i = 0; i < 10; i++) {
+	for (i = 0; i < w83627ehf_num_in; i++) {
 		device_remove_file(dev, &sda_in_input[i].dev_attr);
 		device_remove_file(dev, &sda_in_alarm[i].dev_attr);
 		device_remove_file(dev, &sda_in_min[i].dev_attr);
@@ -1196,7 +1214,11 @@ static int w83627ehf_detect(struct i2c_adapter *adapter)
 	client->flags = 0;
 	dev = &client->dev;
 
-	strlcpy(client->name, "w83627ehf", I2C_NAME_SIZE);
+	if (w83627ehf_num_in == 9)
+		strlcpy(client->name, "w83627dhg", I2C_NAME_SIZE);
+	else	/* just say ehf. 627EHG is 627EHF in lead-free packaging. */
+		strlcpy(client->name, "w83627ehf", I2C_NAME_SIZE);
+
 	data->valid = 0;
 	mutex_init(&data->update_lock);
 
@@ -1246,7 +1268,7 @@ static int w83627ehf_detect(struct i2c_adapter *adapter)
 				goto exit_remove;
 		}
 
-	for (i = 0; i < 10; i++)
+	for (i = 0; i < w83627ehf_num_in; i++)
 		if ((err = device_create_file(dev, &sda_in_input[i].dev_attr))
 			|| (err = device_create_file(dev,
 				&sda_in_alarm[i].dev_attr))
@@ -1340,7 +1362,17 @@ static int __init w83627ehf_find(int sioaddr, unsigned short *addr)
 
 	val = (superio_inb(SIO_REG_DEVID) << 8)
 	    | superio_inb(SIO_REG_DEVID + 1);
-	if ((val & SIO_ID_MASK) != SIO_W83627EHF_ID) {
+	switch (val & SIO_ID_MASK) {
+	case SIO_W83627DHG_ID:
+		w83627ehf_num_in = 9;
+		break;
+	case SIO_W83627EHF_ID:
+	case SIO_W83627EHG_ID:
+		w83627ehf_num_in = 10;
+		break;
+	default:
+		printk(KERN_WARNING "w83627ehf: unsupported chip ID: 0x%04x\n",
+			val);
 		superio_exit();
 		return -ENODEV;
 	}