Merge tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc

Pull MMC update from Chris Ball:
 "MMC highlights for 3.10:

  Core:
   - Introduce MMC_CAP2_NO_PRESCAN_POWERUP to allow skipping
     mmc_power_up() at boot/initialization time if it's already
     happened, for performance (faster boot time) reasons.
   - Fix a bit width test failure that resulted in old eMMC cards being
     put into 1-bit mode when 4-bit mode was available.
   - Expose fwrev/hwrev for MMCv4 parts.
   - Improve card removal logic in the case where the card's removed
     slowly; we were missing card removal events if the card retained
     contact with the slot pads for long enough to reply to a CMD13
     while being removed.

  Drivers:
   - davinci_mmc: Support using PIO instead of DMA.
   - dw_mmc: Add support for Exynos4412.
   - mxcmmc: DT support, use slot-gpio API.
   - mxs-mmc: Add broken-cd/cd-inverted/non-removable DT property
     support.
   - sdhci-sirf: New sdhci-pltfm driver for CSR SiRF SoCs:
       SiRFprimaII: unicore ARM Cortex-A9
       SiRFatlas6: unicore ARM Cortex-A9
       SiRFmarco: dual core ARM Cortex-A9 SMP
   - sdhci-tegra: Add support for Tegra114 platforms, use
     mmc_of_parse()"

* tag 'mmc-updates-for-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
  mmc: sdhci-tegra: fix MODULE_DEVICE_TABLE
  mmc: core: fix init controller performance regression, updated patch
  mmc: mxcmmc: enable DMA support on mpc512x
  mmc: mxcmmc: constify mxcmci_devtype
  mmc: mxcmmc: use slot-gpio API for write-protect detection
  mmc: mxcmmc: add mpc512x SDHC support
  mmc: mxcmmc: fix race conditions for host->req and host->data access
  mmc: mxcmmc: DT support
  mmc: dw_mmc: let device core setup the default pin configuration
  mmc: mxs-mmc: add broken-cd property
  mmc: mxs-mmc: add non-removable property
  mmc: mxs-mmc: add cd-inverted property
  mmc: core: call pm_runtime_put_noidle in pm_runtime_get_sync failed case
  mmc: mxcmmc: Fix bug when card is present during boot
  mmc: core: fix performance regression initializing MMC host controllers
  Revert "mmc: core: wait while adding MMC host to ensure root mounts successfully"
  mmc: atmel-mci: pio hang on block errors
  mmc: core: Fix bit width test failing on old eMMC cards
  mmc: dw_mmc: Use pr_info instead of printk
  mmc: dw_mmc: Check return value of regulator_enable
  ...

49 files changed, 824 insertions, 547 deletions

diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt
new file mode 100644
index 00000000000..db442355cd2
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/fsl-imx-mmc.txt
@@ -0,0 +1,24 @@
+* Freescale Secure Digital Host Controller for i.MX2/3 series
+
+This file documents differences to the properties defined in mmc.txt.
+
+Required properties:
+- compatible : Should be "fsl,<chip>-mmc", chip can be imx21 or imx31
+
+Optional properties:
+- dmas: One DMA phandle with arguments as defined by the devicetree bindings
+	of the used DMA controller.
+- dma-names: Has to be "rx-tx".
+
+Example:
+
+sdhci1: sdhci@10014000 {
+	compatible = "fsl,imx27-mmc", "fsl,imx21-mmc";
+	reg = <0x10014000 0x1000>;
+	interrupts = <11>;
+	dmas = <&dma 7>;
+	dma-names = "rx-tx";
+	bus-width = <4>;
+	cd-gpios = <&gpio3 29>;
+	status = "okay";
+};
diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt
index 3b3a1ee055f..328e990d254 100644
--- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt
+++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt
@@ -5,13 +5,6 @@ MMC, SD and eMMC storage mediums. This file documents differences between the
 core mmc properties described by mmc.txt and the properties used by the
 Samsung implmentation of the SDHCI controller.
 
-Note: The mmc core bindings documentation states that if none of the core
-card-detect bindings are used, then the standard sdhci card detect mechanism
-is used. The Samsung's SDHCI controller bindings extends this as listed below.
-
-[A] The property "samsung,cd-pinmux-gpio" can be used as stated in the
-    "Optional Board Specific Properties" section below.
-
 Required SoC Specific Properties:
 - compatible: should be one of the following
   - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci
@@ -20,18 +13,8 @@ Required SoC Specific Properties:
     controller.
 
 Required Board Specific Properties:
-- Samsung GPIO variant (will be completely replaced by pinctrl):
-  - gpios: Should specify the gpios used for clock, command and data lines. The
-    gpio specifier format depends on the gpio controller.
-- Pinctrl variant (preferred if available):
-  - pinctrl-0: Should specify pin control groups used for this controller.
-  - pinctrl-names: Should contain only one value - "default".
-
-Optional Board Specific Properties:
-- samsung,cd-pinmux-gpio: Specifies the card detect line that is routed
-  through a pinmux to the card-detect pin of the card slot. This property
-  should be used only if none of the mmc core card-detect properties are
-  used. Only for Samsung GPIO variant.
+- pinctrl-0: Should specify pin control groups used for this controller.
+- pinctrl-names: Should contain only one value - "default".
 
 Example:
 	sdhci@12530000 {
@@ -39,19 +22,9 @@ Example:
 		reg = <0x12530000 0x100>;
 		interrupts = <0 75 0>;
 		bus-width = <4>;
-		cd-gpios = <&gpk2 2 2 3 3>;
-
-		/* Samsung GPIO variant */
-		gpios = <&gpk2 0 2 0 3>,  /* clock line */
-			<&gpk2 1 2 0 3>,  /* command line */
-			<&gpk2 3 2 3 3>,  /* data line 0 */
-			<&gpk2 4 2 3 3>,  /* data line 1 */
-			<&gpk2 5 2 3 3>,  /* data line 2 */
-			<&gpk2 6 2 3 3>;  /* data line 3 */
-
-		/* Pinctrl variant */
-		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
+		cd-gpios = <&gpk2 2 0>;
 		pinctrl-names = "default";
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
 	};
 
 	Note: This example shows both SoC specific and board specific properties
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-sirf.txt b/Documentation/devicetree/bindings/mmc/sdhci-sirf.txt
new file mode 100644
index 00000000000..dd6ed464bcb
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sdhci-sirf.txt
@@ -0,0 +1,18 @@
+* SiRFprimII/marco/atlas6 SDHCI Controller
+
+This file documents differences between the core properties in mmc.txt
+and the properties used by the sdhci-sirf driver.
+
+Required properties:
+- compatible: sirf,prima2-sdhc
+
+Optional properties:
+- cd-gpios: card detect gpio, with zero flags.
+
+Example:
+
+	sd0: sdhci@56000000 {
+		compatible = "sirf,prima2-sdhc";
+		reg = <0xcd000000 0x100000>;
+		cd-gpios = <&gpio 6 0>;
+	};
diff --git a/Documentation/mmc/mmc-dev-attrs.txt b/Documentation/mmc/mmc-dev-attrs.txt
index 0d98fac8893..189bab09255 100644
--- a/Documentation/mmc/mmc-dev-attrs.txt
+++ b/Documentation/mmc/mmc-dev-attrs.txt
@@ -22,6 +22,7 @@ All attributes are read-only.
 	manfid			Manufacturer ID (from CID Register)
 	name			Product Name (from CID Register)
 	oemid			OEM/Application ID (from CID Register)
+	prv			Product Revision (from CID Register) (SD and MMCv4 only)
 	serial			Product Serial Number (from CID Register)
 	erase_size		Erase group size
 	preferred_erase_size	Preferred erase size
diff --git a/MAINTAINERS b/MAINTAINERS
index 59d708f2924..e1f5fac1838 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -801,6 +801,7 @@ S:	Maintained
 F:	arch/arm/mach-prima2/
 F:	drivers/dma/sirf-dma.c
 F:	drivers/i2c/busses/i2c-sirf.c
+F:	drivers/mmc/host/sdhci-sirf.c
 F:	drivers/pinctrl/pinctrl-sirf.c
 F:	drivers/spi/spi-sirf.c
 
diff --git a/arch/arm/configs/at91sam9g45_defconfig b/arch/arm/configs/at91sam9g45_defconfig
index 5f551b76cb6..18964cdacd6 100644
--- a/arch/arm/configs/at91sam9g45_defconfig
+++ b/arch/arm/configs/at91sam9g45_defconfig
@@ -173,7 +173,6 @@ CONFIG_MMC=y
 # CONFIG_MMC_BLOCK_BOUNCE is not set
 CONFIG_SDIO_UART=m
 CONFIG_MMC_ATMELMCI=y
-CONFIG_MMC_ATMELMCI_DMA=y
 CONFIG_LEDS_ATMEL_PWM=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_TRIGGER_TIMER=y
diff --git a/arch/avr32/configs/favr-32_defconfig b/arch/avr32/configs/favr-32_defconfig
index 57788a42ff8..c90fbf6d35b 100644
--- a/arch/avr32/configs/favr-32_defconfig
+++ b/arch/avr32/configs/favr-32_defconfig
@@ -122,7 +122,6 @@ CONFIG_USB_G_SERIAL=m
 CONFIG_USB_CDC_COMPOSITE=m
 CONFIG_MMC=y
 CONFIG_MMC_ATMELMCI=y
-CONFIG_MMC_ATMELMCI_DMA=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_ATMEL_PWM=m
diff --git a/arch/avr32/configs/merisc_defconfig b/arch/avr32/configs/merisc_defconfig
index 3befab96682..65de4431108 100644
--- a/arch/avr32/configs/merisc_defconfig
+++ b/arch/avr32/configs/merisc_defconfig
@@ -102,7 +102,6 @@ CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_LOGO=y
 CONFIG_MMC=y
 CONFIG_MMC_ATMELMCI=y
-CONFIG_MMC_ATMELMCI_DMA=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_ATMEL_PWM=y
diff --git a/arch/powerpc/boot/dts/mpc5121.dtsi b/arch/powerpc/boot/dts/mpc5121.dtsi
index 2e82d0e71dd..bd14c00e514 100644
--- a/arch/powerpc/boot/dts/mpc5121.dtsi
+++ b/arch/powerpc/boot/dts/mpc5121.dtsi
@@ -152,6 +152,8 @@
 			compatible = "fsl,mpc5121-sdhc";
 			reg = <0x1500 0x100>;
 			interrupts = <8 0x8>;
+			dmas = <&dma0 30>;
+			dma-names = "rx-tx";
 		};
 
 		i2c@1700 {
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index 5bab73b91c2..e12a03cc2a6 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1932,8 +1932,14 @@ static int mmc_blk_issue_rq(struct mmc_queue *mq, struct request *req)
 	}
 
 out:
-	if (!req && !(mq->flags & MMC_QUEUE_NEW_REQUEST))
-		/* release host only when there are no more requests */
+	if ((!req && !(mq->flags & MMC_QUEUE_NEW_REQUEST)) ||
+	     (req && (req->cmd_flags & MMC_REQ_SPECIAL_MASK)))
+		/*
+		 * Release host when there are no more requests
+		 * and after special request(discard, flush) is done.
+		 * In case sepecial request, there is no reentry to
+		 * the 'mmc_blk_issue_rq' with 'mqrq_prev->req'.
+		 */
 		mmc_release_host(card->host);
 	return ret;
 }
diff --git a/drivers/mmc/card/queue.c b/drivers/mmc/card/queue.c
index fa4e44ee796..9447a0e970d 100644
--- a/drivers/mmc/card/queue.c
+++ b/drivers/mmc/card/queue.c
@@ -22,9 +22,6 @@
 
 #define MMC_QUEUE_BOUNCESZ	65536
 
-
-#define MMC_REQ_SPECIAL_MASK	(REQ_DISCARD | REQ_FLUSH)
-
 /*
  * Prepare a MMC request. This just filters out odd stuff.
  */
diff --git a/drivers/mmc/card/queue.h b/drivers/mmc/card/queue.h
index 031bf6376c9..5752d50049a 100644
--- a/drivers/mmc/card/queue.h
+++ b/drivers/mmc/card/queue.h
@@ -1,6 +1,8 @@
 #ifndef MMC_QUEUE_H
 #define MMC_QUEUE_H
 
+#define MMC_REQ_SPECIAL_MASK	(REQ_DISCARD | REQ_FLUSH)
+
 struct request;
 struct task_struct;
 
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index 9290bb51a06..c40396f2320 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -2289,6 +2289,19 @@ int _mmc_detect_card_removed(struct mmc_host *host)
 		return 1;
 
 	ret = host->bus_ops->alive(host);
+
+	/*
+	 * Card detect status and alive check may be out of sync if card is
+	 * removed slowly, when card detect switch changes while card/slot
+	 * pads are still contacted in hardware (refer to "SD Card Mechanical
+	 * Addendum, Appendix C: Card Detection Switch"). So reschedule a
+	 * detect work 200ms later for this case.
+	 */
+	if (!ret && host->ops->get_cd && !host->ops->get_cd(host)) {
+		mmc_detect_change(host, msecs_to_jiffies(200));
+		pr_debug("%s: card removed too slowly\n", mmc_hostname(host));
+	}
+
 	if (ret) {
 		mmc_card_set_removed(host->card);
 		pr_debug("%s: card remove detected\n", mmc_hostname(host));
@@ -2403,7 +2416,10 @@ void mmc_start_host(struct mmc_host *host)
 {
 	host->f_init = max(freqs[0], host->f_min);
 	host->rescan_disable = 0;
-	mmc_power_up(host);
+	if (host->caps2 & MMC_CAP2_NO_PRESCAN_POWERUP)
+		mmc_power_off(host);
+	else
+		mmc_power_up(host);
 	mmc_detect_change(host, 0);
 }
 
diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c
index c8f3d6e0684..0cbd1effe96 100644
--- a/drivers/mmc/core/mmc.c
+++ b/drivers/mmc/core/mmc.c
@@ -96,6 +96,7 @@ static int mmc_decode_cid(struct mmc_card *card)
 		card->cid.prod_name[3]	= UNSTUFF_BITS(resp, 72, 8);
 		card->cid.prod_name[4]	= UNSTUFF_BITS(resp, 64, 8);
 		card->cid.prod_name[5]	= UNSTUFF_BITS(resp, 56, 8);
+		card->cid.prv		= UNSTUFF_BITS(resp, 48, 8);
 		card->cid.serial	= UNSTUFF_BITS(resp, 16, 32);
 		card->cid.month		= UNSTUFF_BITS(resp, 12, 4);
 		card->cid.year		= UNSTUFF_BITS(resp, 8, 4) + 1997;
@@ -368,13 +369,13 @@ static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
 		ext_csd[EXT_CSD_SEC_FEATURE_SUPPORT];
 	card->ext_csd.raw_trim_mult =
 		ext_csd[EXT_CSD_TRIM_MULT];
+	card->ext_csd.raw_partition_support = ext_csd[EXT_CSD_PARTITION_SUPPORT];
 	if (card->ext_csd.rev >= 4) {
 		/*
 		 * Enhanced area feature support -- check whether the eMMC
 		 * card has the Enhanced area enabled.  If so, export enhanced
 		 * area offset and size to user by adding sysfs interface.
 		 */
-		card->ext_csd.raw_partition_support = ext_csd[EXT_CSD_PARTITION_SUPPORT];
 		if ((ext_csd[EXT_CSD_PARTITION_SUPPORT] & 0x2) &&
 		    (ext_csd[EXT_CSD_PARTITION_ATTRIBUTE] & 0x1)) {
 			hc_erase_grp_sz =
@@ -627,6 +628,7 @@ MMC_DEV_ATTR(hwrev, "0x%x\n", card->cid.hwrev);
 MMC_DEV_ATTR(manfid, "0x%06x\n", card->cid.manfid);
 MMC_DEV_ATTR(name, "%s\n", card->cid.prod_name);
 MMC_DEV_ATTR(oemid, "0x%04x\n", card->cid.oemid);
+MMC_DEV_ATTR(prv, "0x%x\n", card->cid.prv);
 MMC_DEV_ATTR(serial, "0x%08x\n", card->cid.serial);
 MMC_DEV_ATTR(enhanced_area_offset, "%llu\n",
 		card->ext_csd.enhanced_area_offset);
@@ -645,6 +647,7 @@ static struct attribute *mmc_std_attrs[] = {
 	&dev_attr_manfid.attr,
 	&dev_attr_name.attr,
 	&dev_attr_oemid.attr,
+	&dev_attr_prv.attr,
 	&dev_attr_serial.attr,
 	&dev_attr_enhanced_area_offset.attr,
 	&dev_attr_enhanced_area_size.attr,
diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
index aa0719a4dfd..6889a821c1d 100644
--- a/drivers/mmc/core/sdio.c
+++ b/drivers/mmc/core/sdio.c
@@ -861,8 +861,10 @@ static void mmc_sdio_detect(struct mmc_host *host)
 	/* Make sure card is powered before detecting it */
 	if (host->caps & MMC_CAP_POWER_OFF_CARD) {
 		err = pm_runtime_get_sync(&host->card->dev);
-		if (err < 0)
+		if (err < 0) {
+			pm_runtime_put_noidle(&host->card->dev);
 			goto out;
+		}
 	}
 
 	mmc_claim_host(host);
diff --git a/drivers/mmc/core/sdio_bus.c b/drivers/mmc/core/sdio_bus.c
index 5e57048e2c1..546c67c2bbb 100644
--- a/drivers/mmc/core/sdio_bus.c
+++ b/drivers/mmc/core/sdio_bus.c
@@ -16,6 +16,7 @@
 #include <linux/export.h>
 #include <linux/slab.h>
 #include <linux/pm_runtime.h>
+#include <linux/acpi.h>
 
 #include <linux/mmc/card.h>
 #include <linux/mmc/host.h>
@@ -137,7 +138,7 @@ static int sdio_bus_probe(struct device *dev)
 	if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD) {
 		ret = pm_runtime_get_sync(dev);
 		if (ret < 0)
-			goto out;
+			goto disable_runtimepm;
 	}
 
 	/* Set the default block size so the driver is sure it's something
@@ -157,7 +158,6 @@ static int sdio_bus_probe(struct device *dev)
 disable_runtimepm:
 	if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD)
 		pm_runtime_put_noidle(dev);
-out:
 	return ret;
 }
 
@@ -299,6 +299,19 @@ struct sdio_func *sdio_alloc_func(struct mmc_card *card)
 	return func;
 }
 
+#ifdef CONFIG_ACPI
+static void sdio_acpi_set_handle(struct sdio_func *func)
+{
+	struct mmc_host *host = func->card->host;
+	u64 addr = (host->slotno << 16) | func->num;
+
+	ACPI_HANDLE_SET(&func->dev,
+			acpi_get_child(ACPI_HANDLE(host->parent), addr));
+}
+#else
+static inline void sdio_acpi_set_handle(struct sdio_func *func) {}
+#endif
+
 /*
  * Register a new SDIO function with the driver model.
  */
@@ -308,9 +321,12 @@ int sdio_add_func(struct sdio_func *func)
 
 	dev_set_name(&func->dev, "%s:%d", mmc_card_id(func->card), func->num);
 
+	sdio_acpi_set_handle(func);
 	ret = device_add(&func->dev);
-	if (ret == 0)
+	if (ret == 0) {
 		sdio_func_set_present(func);
+		acpi_dev_pm_attach(&func->dev, false);
+	}
 
 	return ret;
 }
@@ -326,6 +342,7 @@ void sdio_remove_func(struct sdio_func *func)
 	if (!sdio_func_present(func))
 		return;
 
+	acpi_dev_pm_detach(&func->dev, false);
 	device_del(&func->dev);
 	put_device(&func->dev);
 }
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index d88219e1d86..9ab8f8dee94 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -190,6 +190,17 @@ config MMC_SDHCI_S3C
 
 	  If unsure, say N.
 
+config MMC_SDHCI_SIRF
+	tristate "SDHCI support on CSR SiRFprimaII and SiRFmarco SoCs"
+	depends on ARCH_SIRF
+	depends on MMC_SDHCI_PLTFM
+	help
+	  This selects the SDHCI support for SiRF System-on-Chip devices.
+
+	  If you have a controller with this interface, say Y or M here.
+
+	  If unsure, say N.
+
 config MMC_SDHCI_PXAV3
 	tristate "Marvell MMP2 SD Host Controller support (PXAV3)"
 	depends on CLKDEV_LOOKUP
@@ -300,16 +311,6 @@ config MMC_ATMELMCI
 
 	  If unsure, say N.
 
-config MMC_ATMELMCI_DMA
-	bool "Atmel MCI DMA support"
-	depends on MMC_ATMELMCI && (AVR32 || ARCH_AT91SAM9G45) && DMA_ENGINE
-	help
-	  Say Y here to have the Atmel MCI driver use a DMA engine to
-	  do data transfers and thus increase the throughput and
-	  reduce the CPU utilization.
-
-	  If unsure, say N.
-
 config MMC_MSM
 	tristate "Qualcomm SDCC Controller Support"
 	depends on MMC && ARCH_MSM
@@ -319,12 +320,12 @@ config MMC_MSM
 	  support for SDIO devices.
 
 config MMC_MXC
-	tristate "Freescale i.MX21/27/31 Multimedia Card Interface support"
-	depends on ARCH_MXC
+	tristate "Freescale i.MX21/27/31 or MPC512x Multimedia Card support"
+	depends on ARCH_MXC || PPC_MPC512x
 	help
-	  This selects the Freescale i.MX21, i.MX27 and i.MX31 Multimedia card
-	  Interface. If you have a i.MX platform with a Multimedia Card slot,
-	  say Y or M here.
+	  This selects the Freescale i.MX21, i.MX27, i.MX31 or MPC512x
+	  Multimedia Card Interface. If you have an i.MX or MPC512x platform
+	  with a Multimedia Card slot, say Y or M here.
 
 	  If unsure, say N.
 
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index c380e3cf0a3..cd322807555 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -13,6 +13,7 @@ obj-$(CONFIG_MMC_SDHCI_ACPI)	+= sdhci-acpi.o
 obj-$(CONFIG_MMC_SDHCI_PXAV3)	+= sdhci-pxav3.o
 obj-$(CONFIG_MMC_SDHCI_PXAV2)	+= sdhci-pxav2.o
 obj-$(CONFIG_MMC_SDHCI_S3C)	+= sdhci-s3c.o
+obj-$(CONFIG_MMC_SDHCI_SIRF)   	+= sdhci-sirf.o
 obj-$(CONFIG_MMC_SDHCI_SPEAR)	+= sdhci-spear.o
 obj-$(CONFIG_MMC_WBSD)		+= wbsd.o
 obj-$(CONFIG_MMC_AU1X)		+= au1xmmc.o
diff --git a/drivers/mmc/host/android-goldfish.c b/drivers/mmc/host/android-goldfish.c
index ef3aef0f376..7780c14704c 100644
--- a/drivers/mmc/host/android-goldfish.c
+++ b/drivers/mmc/host/android-goldfish.c
@@ -476,7 +476,7 @@ static int goldfish_mmc_probe(struct platform_device *pdev)
 	host->mmc = mmc;
 
 	pr_err("mmc: Mapping %lX to %lX\n", (long)res->start, (long)res->end);
-	host->reg_base = ioremap(res->start, res->end - res->start + 1);
+	host->reg_base = ioremap(res->start, resource_size(res));
 	if (host->reg_base == NULL) {
 		ret = -ENOMEM;
 		goto ioremap_failed;
diff --git a/drivers/mmc/host/atmel-mci.c b/drivers/mmc/host/atmel-mci.c
index 722af1de796..e75774f7260 100644
--- a/drivers/mmc/host/atmel-mci.c
+++ b/drivers/mmc/host/atmel-mci.c
@@ -178,6 +178,7 @@ struct atmel_mci {
 	void __iomem		*regs;
 
 	struct scatterlist	*sg;
+	unsigned int		sg_len;
 	unsigned int		pio_offset;
 	unsigned int		*buffer;
 	unsigned int		buf_size;
@@ -892,6 +893,7 @@ static u32 atmci_prepare_data(struct atmel_mci *host, struct mmc_data *data)
 	data->error = -EINPROGRESS;
 
 	host->sg = data->sg;
+	host->sg_len = data->sg_len;
 	host->data = data;
 	host->data_chan = NULL;
 
@@ -1826,7 +1828,8 @@ static void atmci_read_data_pio(struct atmel_mci *host)
 			if (offset == sg->length) {
 				flush_dcache_page(sg_page(sg));
 				host->sg = sg = sg_next(sg);
-				if (!sg)
+				host->sg_len--;
+				if (!sg || !host->sg_len)
 					goto done;
 
 				offset = 0;
@@ -1839,7 +1842,8 @@ static void atmci_read_data_pio(struct atmel_mci *host)
 
 			flush_dcache_page(sg_page(sg));
 			host->sg = sg = sg_next(sg);
-			if (!sg)
+			host->sg_len--;
+			if (!sg || !host->sg_len)
 				goto done;
 
 			offset = 4 - remaining;
@@ -1890,7 +1894,8 @@ static void atmci_write_data_pio(struct atmel_mci *host)
 			nbytes += 4;
 			if (offset == sg->length) {
 				host->sg = sg = sg_next(sg);
-				if (!sg)
+				host->sg_len--;
+				if (!sg || !host->sg_len)
 					goto done;
 
 				offset = 0;
@@ -1904,7 +1909,8 @@ static void atmci_write_data_pio(struct atmel_mci *host)
 			nbytes += remaining;
 
 			host->sg = sg = sg_next(sg);
-			if (!sg) {
+			host->sg_len--;
+			if (!sg || !host->sg_len) {
 				atmci_writel(host, ATMCI_TDR, value);
 				goto done;
 			}
@@ -2487,10 +2493,8 @@ static int __exit atmci_remove(struct platform_device *pdev)
 	atmci_readl(host, ATMCI_SR);
 	clk_disable(host->mck);
 
-#ifdef CONFIG_MMC_ATMELMCI_DMA
 	if (host->dma.chan)
 		dma_release_channel(host->dma.chan);
-#endif
 
 	free_irq(platform_get_irq(pdev, 0), host);
 	iounmap(host->regs);
diff --git a/drivers/mmc/host/davinci_mmc.c b/drivers/mmc/host/davinci_mmc.c
index f8a96d652e9..3946a0eb3a0 100644
--- a/drivers/mmc/host/davinci_mmc.c
+++ b/drivers/mmc/host/davinci_mmc.c
@@ -1264,13 +1264,15 @@ static int __init davinci_mmcsd_probe(struct platform_device *pdev)
 
 	r = platform_get_resource(pdev, IORESOURCE_DMA, 0);
 	if (!r)
-		goto out;
-	host->rxdma = r->start;
+		dev_