Merge branch 'for-2.6.25' of master.kernel.org:/pub/scm/linux/kernel/git/jwboyer/powerpc-4xx

20 files changed, 2102 insertions, 64 deletions

diff --git a/Documentation/powerpc/booting-without-of.txt b/Documentation/powerpc/booting-without-of.txt
index b5e46efeba8..7b4e8a70882 100644
--- a/Documentation/powerpc/booting-without-of.txt
+++ b/Documentation/powerpc/booting-without-of.txt
@@ -57,6 +57,7 @@ Table of Contents
       n) 4xx/Axon EMAC ethernet nodes
       o) Xilinx IP cores
       p) Freescale Synchronous Serial Interface
+	  q) USB EHCI controllers
 
   VII - Specifying interrupt information for devices
     1) interrupts property
@@ -2577,6 +2578,20 @@ platforms are moved over to use the flattened-device-tree model.
       Requred properties:
        - current-speed : Baud rate of uartlite
 
+      v) Xilinx hwicap
+
+		Xilinx hwicap devices provide access to the configuration logic
+		of the FPGA through the Internal Configuration Access Port
+		(ICAP).  The ICAP enables partial reconfiguration of the FPGA,
+		readback of the configuration information, and some control over
+		'warm boots' of the FPGA fabric.
+
+		Required properties:
+		- xlnx,family : The family of the FPGA, necessary since the
+                      capabilities of the underlying ICAP hardware
+                      differ between different families.  May be
+                      'virtex2p', 'virtex4', or 'virtex5'.
+
     p) Freescale Synchronous Serial Interface
 
        The SSI is a serial device that communicates with audio codecs.  It can
@@ -2775,6 +2790,33 @@ platforms are moved over to use the flattened-device-tree model.
 		interrupt-parent = < &ipic >;
         };
 
+    q) USB EHCI controllers
+
+    Required properties:
+      - compatible : should be "usb-ehci".
+      - reg : should contain at least address and length of the standard EHCI
+        register set for the device. Optional platform-dependent registers
+        (debug-port or other) can be also specified here, but only after
+        definition of standard EHCI registers.
+      - interrupts : one EHCI interrupt should be described here.
+    If device registers are implemented in big endian mode, the device
+    node should have "big-endian-regs" property.
+    If controller implementation operates with big endian descriptors,
+    "big-endian-desc" property should be specified.
+    If both big endian registers and descriptors are used by the controller
+    implementation, "big-endian" property can be specified instead of having
+    both "big-endian-regs" and "big-endian-desc".
+
+     Example (Sequoia 440EPx):
+	    ehci@e0000300 {
+		   compatible = "ibm,usb-ehci-440epx", "usb-ehci";
+		   interrupt-parent = <&UIC0>;
+		   interrupts = <1a 4>;
+		   reg = <0 e0000300 90 0 e0000390 70>;
+		   big-endian;
+	   };
+
+
    More devices will be defined as this spec matures.
 
 VII - Specifying interrupt information for devices
diff --git a/arch/powerpc/boot/dts/sequoia.dts b/arch/powerpc/boot/dts/sequoia.dts
index d9046c1adcb..5c13d46f441 100644
--- a/arch/powerpc/boot/dts/sequoia.dts
+++ b/arch/powerpc/boot/dts/sequoia.dts
@@ -138,6 +138,14 @@
 			interrupts = <15 8>;
 		};
 
+		USB0: ehci@e0000300 {
+			compatible = "ibm,usb-ehci-440epx", "usb-ehci";
+			interrupt-parent = <&UIC0>;
+			interrupts = <1a 4>;
+			reg = <0 e0000300 90 0 e0000390 70>;
+			big-endian;
+		};
+
 		POB0: opb {
 		  	compatible = "ibm,opb-440epx", "ibm,opb";
 			#address-cells = <1>;
diff --git a/arch/powerpc/platforms/40x/Kconfig b/arch/powerpc/platforms/40x/Kconfig
index 74f31177e47..a9260e21451 100644
--- a/arch/powerpc/platforms/40x/Kconfig
+++ b/arch/powerpc/platforms/40x/Kconfig
@@ -72,6 +72,7 @@ config WALNUT
 	default y
 	select 405GP
 	select PCI
+	select OF_RTC
 	help
 	  This option enables support for the IBM PPC405GP evaluation board.
 
diff --git a/arch/powerpc/platforms/40x/virtex.c b/arch/powerpc/platforms/40x/virtex.c
index 88b66444dfb..0422590040d 100644
--- a/arch/powerpc/platforms/40x/virtex.c
+++ b/arch/powerpc/platforms/40x/virtex.c
@@ -37,7 +37,7 @@ static int __init virtex_probe(void)
 {
 	unsigned long root = of_get_flat_dt_root();
 
-	if (!of_flat_dt_is_compatible(root, "xilinx,virtex"))
+	if (!of_flat_dt_is_compatible(root, "xlnx,virtex"))
 		return 0;
 
 	return 1;
diff --git a/arch/powerpc/platforms/40x/walnut.c b/arch/powerpc/platforms/40x/walnut.c
index 5d9edd917f9..b8b257efeb7 100644
--- a/arch/powerpc/platforms/40x/walnut.c
+++ b/arch/powerpc/platforms/40x/walnut.c
@@ -18,6 +18,7 @@
 
 #include <linux/init.h>
 #include <linux/of_platform.h>
+#include <linux/rtc.h>
 
 #include <asm/machdep.h>
 #include <asm/prom.h>
diff --git a/arch/powerpc/platforms/44x/warp.c b/arch/powerpc/platforms/44x/warp.c
index 8f01563dbd2..da5b7b7599d 100644
--- a/arch/powerpc/platforms/44x/warp.c
+++ b/arch/powerpc/platforms/44x/warp.c
@@ -137,7 +137,7 @@ static int __init pika_dtm_start(void)
 	}
 	of_node_put(np);
 
-	fpga = ioremap(res.start + 0x20, 4);
+	fpga = ioremap(res.start, 0x24);
 	if (fpga == NULL)
 		return -ENOENT;
 
diff --git a/arch/powerpc/sysdev/dcr.c b/arch/powerpc/sysdev/dcr.c
index 427027c7ea0..437e48d3ae3 100644
--- a/arch/powerpc/sysdev/dcr.c
+++ b/arch/powerpc/sysdev/dcr.c
@@ -137,5 +137,6 @@ void dcr_unmap(dcr_host_t host, unsigned int dcr_c)
 	h.token = NULL;
 }
 EXPORT_SYMBOL_GPL(dcr_unmap);
-
-#endif /* !defined(CONFIG_PPC_DCR_NATIVE) */
+#else	/* defined(CONFIG_PPC_DCR_NATIVE) */
+DEFINE_SPINLOCK(dcr_ind_lock);
+#endif	/* !defined(CONFIG_PPC_DCR_NATIVE) */
diff --git a/drivers/block/xsysace.c b/drivers/block/xsysace.c
index 78ebfffc77e..4a7a059ebaf 100644
--- a/drivers/block/xsysace.c
+++ b/drivers/block/xsysace.c
@@ -1202,8 +1202,10 @@ static int __devexit ace_of_remove(struct of_device *op)
 }
 
 /* Match table for of_platform binding */
-static struct of_device_id __devinit ace_of_match[] = {
-	{ .compatible = "xilinx,xsysace", },
+static struct of_device_id ace_of_match[] __devinitdata = {
+	{ .compatible = "xlnx,opb-sysace-1.00.b", },
+	{ .compatible = "xlnx,opb-sysace-1.00.c", },
+	{ .compatible = "xlnx,xps-sysace-1.00.a", },
 	{},
 };
 MODULE_DEVICE_TABLE(of, ace_of_match);
diff --git a/drivers/char/Kconfig b/drivers/char/Kconfig
index 46662959477..be8371ac308 100644
--- a/drivers/char/Kconfig
+++ b/drivers/char/Kconfig
@@ -841,6 +841,16 @@ config DTLK
 	  To compile this driver as a module, choose M here: the
 	  module will be called dtlk.
 
+config XILINX_HWICAP
+	tristate "Xilinx HWICAP Support"
+	depends on XILINX_VIRTEX
+	help
+	  This option enables support for Xilinx Internal Configuration
+	  Access Port (ICAP) driver.  The ICAP is used on Xilinx Virtex
+	  FPGA platforms to partially reconfigure the FPGA at runtime.
+
+	  If unsure, say N.
+
 config R3964
 	tristate "Siemens R3964 line discipline"
 	---help---
diff --git a/drivers/char/Makefile b/drivers/char/Makefile
index 96fc01eddef..686fabbd85c 100644
--- a/drivers/char/Makefile
+++ b/drivers/char/Makefile
@@ -77,6 +77,7 @@ obj-$(CONFIG_EFI_RTC)		+= efirtc.o
 obj-$(CONFIG_SGI_DS1286)	+= ds1286.o
 obj-$(CONFIG_SGI_IP27_RTC)	+= ip27-rtc.o
 obj-$(CONFIG_DS1302)		+= ds1302.o
+obj-$(CONFIG_XILINX_HWICAP)	+= xilinx_hwicap/
 ifeq ($(CONFIG_GENERIC_NVRAM),y)
   obj-$(CONFIG_NVRAM)	+= generic_nvram.o
 else
diff --git a/drivers/char/xilinx_hwicap/Makefile b/drivers/char/xilinx_hwicap/Makefile
new file mode 100644
index 00000000000..5491cbc42f4
--- /dev/null
+++ b/drivers/char/xilinx_hwicap/Makefile
@@ -0,0 +1,7 @@
+#
+# Makefile for the Xilinx OPB hwicap driver
+#
+
+obj-$(CONFIG_XILINX_HWICAP) += xilinx_hwicap_m.o 
+ 
+xilinx_hwicap_m-y := xilinx_hwicap.o fifo_icap.o buffer_icap.o
diff --git a/drivers/char/xilinx_hwicap/buffer_icap.c b/drivers/char/xilinx_hwicap/buffer_icap.c
new file mode 100644
index 00000000000..dfea2bde162
--- /dev/null
+++ b/drivers/char/xilinx_hwicap/buffer_icap.c
@@ -0,0 +1,380 @@
+/*****************************************************************************
+ *
+ *     Author: Xilinx, Inc.
+ *
+ *     This program is free software; you can redistribute it and/or modify it
+ *     under the terms of the GNU General Public License as published by the
+ *     Free Software Foundation; either version 2 of the License, or (at your
+ *     option) any later version.
+ *
+ *     XILINX IS PROVIDING THIS DESIGN, CODE, OR INFORMATION "AS IS"
+ *     AS A COURTESY TO YOU, SOLELY FOR USE IN DEVELOPING PROGRAMS AND
+ *     SOLUTIONS FOR XILINX DEVICES.  BY PROVIDING THIS DESIGN, CODE,
+ *     OR INFORMATION AS ONE POSSIBLE IMPLEMENTATION OF THIS FEATURE,
+ *     APPLICATION OR STANDARD, XILINX IS MAKING NO REPRESENTATION
+ *     THAT THIS IMPLEMENTATION IS FREE FROM ANY CLAIMS OF INFRINGEMENT,
+ *     AND YOU ARE RESPONSIBLE FOR OBTAINING ANY RIGHTS YOU MAY REQUIRE
+ *     FOR YOUR IMPLEMENTATION.  XILINX EXPRESSLY DISCLAIMS ANY
+ *     WARRANTY WHATSOEVER WITH RESPECT TO THE ADEQUACY OF THE
+ *     IMPLEMENTATION, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OR
+ *     REPRESENTATIONS THAT THIS IMPLEMENTATION IS FREE FROM CLAIMS OF
+ *     INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ *     FOR A PARTICULAR PURPOSE.
+ *
+ *     Xilinx products are not intended for use in life support appliances,
+ *     devices, or systems. Use in such applications is expressly prohibited.
+ *
+ *     (c) Copyright 2003-2008 Xilinx Inc.
+ *     All rights reserved.
+ *
+ *     You should have received a copy of the GNU General Public License along
+ *     with this program; if not, write to the Free Software Foundation, Inc.,
+ *     675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *****************************************************************************/
+
+#include "buffer_icap.h"
+
+/* Indicates how many bytes will fit in a buffer. (1 BRAM) */
+#define XHI_MAX_BUFFER_BYTES        2048
+#define XHI_MAX_BUFFER_INTS         (XHI_MAX_BUFFER_BYTES >> 2)
+
+/* File access and error constants */
+#define XHI_DEVICE_READ_ERROR       -1
+#define XHI_DEVICE_WRITE_ERROR      -2
+#define XHI_BUFFER_OVERFLOW_ERROR   -3
+
+#define XHI_DEVICE_READ             0x1
+#define XHI_DEVICE_WRITE            0x0
+
+/* Constants for checking transfer status */
+#define XHI_CYCLE_DONE              0
+#define XHI_CYCLE_EXECUTING         1
+
+/* buffer_icap register offsets */
+
+/* Size of transfer, read & write */
+#define XHI_SIZE_REG_OFFSET        0x800L
+/* offset into bram, read & write */
+#define XHI_BRAM_OFFSET_REG_OFFSET 0x804L
+/* Read not Configure, direction of transfer.  Write only */
+#define XHI_RNC_REG_OFFSET         0x808L
+/* Indicates transfer complete. Read only */
+#define XHI_STATUS_REG_OFFSET      0x80CL
+
+/* Constants for setting the RNC register */
+#define XHI_CONFIGURE              0x0UL
+#define XHI_READBACK               0x1UL
+
+/* Constants for the Done register */
+#define XHI_NOT_FINISHED           0x0UL
+#define XHI_FINISHED               0x1UL
+
+#define XHI_BUFFER_START 0
+
+/**
+ * buffer_icap_get_status: Get the contents of the status register.
+ * @parameter base_address: is the base address of the device
+ *
+ * The status register contains the ICAP status and the done bit.
+ *
+ * D8 - cfgerr
+ * D7 - dalign
+ * D6 - rip
+ * D5 - in_abort_l
+ * D4 - Always 1
+ * D3 - Always 1
+ * D2 - Always 1
+ * D1 - Always 1
+ * D0 - Done bit
+ **/
+static inline u32 buffer_icap_get_status(void __iomem *base_address)
+{
+	return in_be32(base_address + XHI_STATUS_REG_OFFSET);
+}
+
+/**
+ * buffer_icap_get_bram: Reads data from the storage buffer bram.
+ * @parameter base_address: contains the base address of the component.
+ * @parameter offset: The word offset from which the data should be read.
+ *
+ * A bram is used as a configuration memory cache.  One frame of data can
+ * be stored in this "storage buffer".
+ **/
+static inline u32 buffer_icap_get_bram(void __iomem *base_address,
+		u32 offset)
+{
+	return in_be32(base_address + (offset << 2));
+}
+
+/**
+ * buffer_icap_busy: Return true if the icap device is busy
+ * @parameter base_address: is the base address of the device
+ *
+ * The queries the low order bit of the status register, which
+ * indicates whether the current configuration or readback operation
+ * has completed.
+ **/
+static inline bool buffer_icap_busy(void __iomem *base_address)
+{
+	return (buffer_icap_get_status(base_address) & 1) == XHI_NOT_FINISHED;
+}
+
+/**
+ * buffer_icap_busy: Return true if the icap device is not busy
+ * @parameter base_address: is the base address of the device
+ *
+ * The queries the low order bit of the status register, which
+ * indicates whether the current configuration or readback operation
+ * has completed.
+ **/
+static inline bool buffer_icap_done(void __iomem *base_address)
+{
+	return (buffer_icap_get_status(base_address) & 1) == XHI_FINISHED;
+}
+
+/**
+ * buffer_icap_set_size: Set the size register.
+ * @parameter base_address: is the base address of the device
+ * @parameter data: The size in bytes.
+ *
+ * The size register holds the number of 8 bit bytes to transfer between
+ * bram and the icap (or icap to bram).
+ **/
+static inline void buffer_icap_set_size(void __iomem *base_address,
+		u32 data)
+{
+	out_be32(base_address + XHI_SIZE_REG_OFFSET, data);
+}
+
+/**
+ * buffer_icap_mSetoffsetReg: Set the bram offset register.
+ * @parameter base_address: contains the base address of the device.
+ * @parameter data: is the value to be written to the data register.
+ *
+ * The bram offset register holds the starting bram address to transfer
+ * data from during configuration or write data to during readback.
+ **/
+static inline void buffer_icap_set_offset(void __iomem *base_address,
+		u32 data)
+{
+	out_be32(base_address + XHI_BRAM_OFFSET_REG_OFFSET, data);
+}
+
+/**
+ * buffer_icap_set_rnc: Set the RNC (Readback not Configure) register.
+ * @parameter base_address: contains the base address of the device.
+ * @parameter data: is the value to be written to the data register.
+ *
+ * The RNC register determines the direction of the data transfer.  It
+ * controls whether a configuration or readback take place.  Writing to
+ * this register initiates the transfer.  A value of 1 initiates a
+ * readback while writing a value of 0 initiates a configuration.
+ **/
+static inline void buffer_icap_set_rnc(void __iomem *base_address,
+		u32 data)
+{
+	out_be32(base_address + XHI_RNC_REG_OFFSET, data);
+}
+
+/**
+ * buffer_icap_set_bram: Write data to the storage buffer bram.
+ * @parameter base_address: contains the base address of the component.
+ * @parameter offset: The word offset at which the data should be written.
+ * @parameter data: The value to be written to the bram offset.
+ *
+ * A bram is used as a configuration memory cache.  One frame of data can
+ * be stored in this "storage buffer".
+ **/
+static inline void buffer_icap_set_bram(void __iomem *base_address,
+		u32 offset, u32 data)
+{
+	out_be32(base_address + (offset << 2), data);
+}
+
+/**
+ * buffer_icap_device_read: Transfer bytes from ICAP to the storage buffer.
+ * @parameter drvdata: a pointer to the drvdata.
+ * @parameter offset: The storage buffer start address.
+ * @parameter count: The number of words (32 bit) to read from the
+ *           device (ICAP).
+ **/
+static int buffer_icap_device_read(struct hwicap_drvdata *drvdata,
+		u32 offset, u32 count)
+{
+
+	s32 retries = 0;
+	void __iomem *base_address = drvdata->base_address;
+
+	if (buffer_icap_busy(base_address))
+		return -EBUSY;
+
+	if ((offset + count) > XHI_MAX_BUFFER_INTS)
+		return -EINVAL;
+
+	/* setSize count*4 to get bytes. */
+	buffer_icap_set_size(base_address, (count << 2));
+	buffer_icap_set_offset(base_address, offset);
+	buffer_icap_set_rnc(base_address, XHI_READBACK);
+
+	while (buffer_icap_busy(base_address)) {
+		retries++;
+		if (retries > XHI_MAX_RETRIES)
+			return -EBUSY;
+	}
+	return 0;
+
+};
+
+/**
+ * buffer_icap_device_write: Transfer bytes from ICAP to the storage buffer.
+ * @parameter drvdata: a pointer to the drvdata.
+ * @parameter offset: The storage buffer start address.
+ * @parameter count: The number of words (32 bit) to read from the
+ *           device (ICAP).
+ **/
+static int buffer_icap_device_write(struct hwicap_drvdata *drvdata,
+		u32 offset, u32 count)
+{
+
+	s32 retries = 0;
+	void __iomem *base_address = drvdata->base_address;
+
+	if (buffer_icap_busy(base_address))
+		return -EBUSY;
+
+	if ((offset + count) > XHI_MAX_BUFFER_INTS)
+		return -EINVAL;
+
+	/* setSize count*4 to get bytes. */
+	buffer_icap_set_size(base_address, count << 2);
+	buffer_icap_set_offset(base_address, offset);
+	buffer_icap_set_rnc(base_address, XHI_CONFIGURE);
+
+	while (buffer_icap_busy(base_address)) {
+		retries++;
+		if (retries > XHI_MAX_RETRIES)
+			return -EBUSY;
+	}
+	return 0;
+
+};
+
+/**
+ * buffer_icap_reset: Reset the logic of the icap device.
+ * @parameter drvdata: a pointer to the drvdata.
+ *
+ * Writing to the status register resets the ICAP logic in an internal
+ * version of the core.  For the version of the core published in EDK,
+ * this is a noop.
+ **/
+void buffer_icap_reset(struct hwicap_drvdata *drvdata)
+{
+    out_be32(drvdata->base_address + XHI_STATUS_REG_OFFSET, 0xFEFE);
+}
+
+/**
+ * buffer_icap_set_configuration: Load a partial bitstream from system memory.
+ * @parameter drvdata: a pointer to the drvdata.
+ * @parameter data: Kernel address of the partial bitstream.
+ * @parameter size: the size of the partial bitstream in 32 bit words.
+ **/
+int buffer_icap_set_configuration(struct hwicap_drvdata *drvdata, u32 *data,
+			     u32 size)
+{
+	int status;
+	s32 buffer_count = 0;
+	s32 num_writes = 0;
+	bool dirty = 0;
+	u32 i;
+	void __iomem *base_address = drvdata->base_address;
+
+	/* Loop through all the data */
+	for (i = 0, buffer_count = 0; i < size; i++) {
+
+		/* Copy data to bram */
+		buffer_icap_set_bram(base_address, buffer_count, data[i]);
+		dirty = 1;
+
+		if (buffer_count < XHI_MAX_BUFFER_INTS - 1) {
+			buffer_count++;
+			continue;
+		}
+
+		/* Write data to ICAP */
+		status = buffer_icap_device_write(
+				drvdata,
+				XHI_BUFFER_START,
+				XHI_MAX_BUFFER_INTS);
+		if (status != 0) {
+			/* abort. */
+			buffer_icap_reset(drvdata);
+			return status;
+		}
+
+		buffer_count = 0;
+		num_writes++;
+		dirty = 0;
+	}
+
+	/* Write unwritten data to ICAP */
+	if (dirty) {
+		/* Write data to ICAP */
+		status = buffer_icap_device_write(drvdata, XHI_BUFFER_START,
+					     buffer_count);
+		if (status != 0) {
+			/* abort. */
+			buffer_icap_reset(drvdata);
+		}
+		return status;
+	}
+
+	return 0;
+};
+
+/**
+ * buffer_icap_get_configuration: Read configuration data from the device.
+ * @parameter drvdata: a pointer to the drvdata.
+ * @parameter data: Address of the data representing the partial bitstream
+ * @parameter size: the size of the partial bitstream in 32 bit words.
+ **/
+int buffer_icap_get_configuration(struct hwicap_drvdata *drvdata, u32 *data,
+			     u32 size)
+{
+	int status;
+	s32 buffer_count = 0;
+	s32 read_count = 0;
+	u32 i;
+	void __iomem *base_address = drvdata->base_address;
+
+	/* Loop through all the data */
+	for (i = 0, buffer_count = XHI_MAX_BUFFER_INTS; i < size; i++) {
+		if (buffer_count == XHI_MAX_BUFFER_INTS) {
+			u32 words_remaining = size - i;
+			u32 words_to_read =
+				words_remaining <
+				XHI_MAX_BUFFER_INTS ? words_remaining :
+				XHI_MAX_BUFFER_INTS;
+
+			/* Read data from ICAP */
+			status = buffer_icap_device_read(
+					drvdata,
+					XHI_BUFFER_START,
+					words_to_read);
+			if (status != 0) {
+				/* abort. */
+				buffer_icap_reset(drvdata);
+				return status;
+			}
+
+			buffer_count = 0;
+			read_count++;
+		}
+
+		/* Copy data from bram */
+		data[i] = buffer_icap_get_bram(base_address, buffer_count);
+		buffer_count++;
+	}
+
+	return 0;
+};
diff --git a/drivers/char/xilinx_hwicap/buffer_icap.h b/drivers/char/xilinx_hwicap/buffer_icap.h
new file mode 100644
index 00000000000..03184959fa0
--- /dev/null
+++ b/drivers/char/xilinx_hwicap/buffer_icap.h
@@ -0,0 +1,57 @@
+/*****************************************************************************
+ *
+ *     Author: Xilinx, Inc.
+ *
+ *     This program is free software; you can redistribute it and/or modify it
+ *     under the terms of the GNU General Public License as published by the
+ *     Free Software Foundation; either version 2 of the License, or (at your
+ *     option) any later version.
+ *
+ *     XILINX IS PROVIDING THIS DESIGN, CODE, OR INFORMATION "AS IS"
+ *     AS A COURTESY TO YOU, SOLELY FOR USE IN DEVELOPING PROGRAMS AND
+ *     SOLUTIONS FOR XILINX DEVICES.  BY PROVIDING THIS DESIGN, CODE,
+ *     OR INFORMATION AS ONE POSSIBLE IMPLEMENTATION OF THIS FEATURE,
+ *     APPLICATION OR STANDARD, XILINX IS MAKING NO REPRESENTATION
+ *     THAT THIS IMPLEMENTATION IS FREE FROM ANY CLAIMS OF INFRINGEMENT,
+ *     AND YOU ARE RESPONSIBLE FOR OBTAINING ANY RIGHTS YOU MAY REQUIRE
+ *     FOR YOUR IMPLEMENTATION.  XILINX EXPRESSLY DISCLAIMS ANY
+ *     WARRANTY WHATSOEVER WITH RESPECT TO THE ADEQUACY OF THE
+ *     IMPLEMENTATION, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OR
+ *     REPRESENTATIONS THAT THIS IMPLEMENTATION IS FREE FROM CLAIMS OF
+ *     INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ *     FOR A PARTICULAR PURPOSE.
+ *
+ *     Xilinx products are not intended for use in life support appliances,
+ *     devices, or systems. Use in such applications is expressly prohibited.
+ *
+ *     (c) Copyright 2003-2008 Xilinx Inc.
+ *     All rights reserved.
+ *
+ *     You should have received a copy of the GNU General Public License along
+ *     with this program; if not, write to the Free Software Foundation, Inc.,
+ *     675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *****************************************************************************/
+
+#ifndef XILINX_BUFFER_ICAP_H_	/* prevent circular inclusions */
+#define XILINX_BUFFER_ICAP_H_	/* by using protection macros */
+
+#include <linux/types.h>
+#include <linux/cdev.h>
+#include <linux/version.h>
+#include <linux/platform_device.h>
+
+#include <asm/io.h>
+#include "xilinx_hwicap.h"
+
+void buffer_icap_reset(struct hwicap_drvdata *drvdata);
+
+/* Loads a partial bitstream from system memory. */
+int buffer_icap_set_configuration(struct hwicap_drvdata *drvdata, u32 *data,
+			     u32 Size);
+
+/* Loads a partial bitstream from system memory. */
+int buffer_icap_get_configuration(struct hwicap_drvdata *drvdata, u32 *data,
+			     u32 Size);
+
+#endif
diff --git a/drivers/char/xilinx_hwicap/fifo_icap.c b/drivers/char/xilinx_hwicap/fifo_icap.c
new file mode 100644
index 00000000000..0988314694a
--- /dev/null
+++ b/drivers/char/xilinx_hwicap/fifo_icap.c
@@ -0,0 +1,381 @@
+/*****************************************************************************
+ *
+ *     Author: Xilinx, Inc.
+ *
+ *     This program is free software; you can redistribute it and/or modify it
+ *     under the terms of the GNU General Public License as published by the
+ *     Free Software Foundation; either version 2 of the License, or (at your
+ *     option) any later version.
+ *
+ *     XILINX IS PROVIDING THIS DESIGN, CODE, OR INFORMATION "AS IS"
+ *     AS A COURTESY TO YOU, SOLELY FOR USE IN DEVELOPING PROGRAMS AND
+ *     SOLUTIONS FOR XILINX DEVICES.  BY PROVIDING THIS DESIGN, CODE,
+ *     OR INFORMATION AS ONE POSSIBLE IMPLEMENTATION OF THIS FEATURE,
+ *     APPLICATION OR STANDARD, XILINX IS MAKING NO REPRESENTATION
+ *     THAT THIS IMPLEMENTATION IS FREE FROM ANY CLAIMS OF INFRINGEMENT,
+ *     AND YOU ARE RESPONSIBLE FOR OBTAINING ANY RIGHTS YOU MAY REQUIRE
+ *     FOR YOUR IMPLEMENTATION.  XILINX EXPRESSLY DISCLAIMS ANY
+ *     WARRANTY WHATSOEVER WITH RESPECT TO THE ADEQUACY OF THE
+ *     IMPLEMENTATION, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OR
+ *     REPRESENTATIONS THAT THIS IMPLEMENTATION IS FREE FROM CLAIMS OF
+ *     INFRINGEMENT, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ *     FOR A PARTICULAR PURPOSE.
+ *
+ *     Xilinx products are not intended for use in life support appliances,
+ *     devices, or systems. Use in such applications is expressly prohibited.
+ *
+ *     (c) Copyright 2007-2008 Xilinx Inc.
+ *     All rights reserved.
+ *
+ *     You should have received a copy of the GNU General Public License along
+ *     with this program; if not, write to the Free Software Foundation, Inc.,
+ *     675 Mass Ave, Cambridge, MA 02139, USA.
+ *
+ *****************************************************************************/
+
+#include "fifo_icap.h"
+
+/* Register offsets for the XHwIcap device. */
+#define XHI_GIER_OFFSET	0x1C  /* Device Global Interrupt Enable Reg */
+#define XHI_IPISR_OFFSET 0x20  /* Interrupt Status Register */
+#define XHI_IPIER_OFFSET 0x28  /* Interrupt Enable Register */
+#define XHI_WF_OFFSET 0x100 /* Write FIFO */
+#define XHI_RF_OFFSET 0x104 /* Read FIFO */
+#define XHI_SZ_OFFSET 0x108 /* Size Register */
+#define XHI_CR_OFFSET 0x10C /* Control Register */
+#define XHI_SR_OFFSET 0x110 /* Status Register */
+#define XHI_WFV_OFFSET 0x114 /* Write FIFO Vacancy Register */
+#define XHI_RFO_OFFSET 0x118 /* Read FIFO Occupancy Register */
+
+/* Device Global Interrupt Enable Register (GIER) bit definitions */
+
+#define XHI_GIER_GIE_MASK 0x80000000 /* Global Interrupt enable Mask */
+
+/**
+ * HwIcap Device Interrupt Status/Enable Registers
+ *
+ * Interrupt Status Register (IPISR) : This register holds the
+ * interrupt status flags for the device. These bits are toggle on
+ * write.
+ *
+ * Interrupt Enable Register (IPIER) : This register is used to enable
+ * interrupt sources for the device.
+ * Writing a '1' to a bit enables the corresponding interrupt.
+ * Writing a '0' to a bit disables the corresponding interrupt.
+ *
+ * IPISR/IPIER registers have the same bit definitions and are only defined
+ * once.
+ */
+#define XHI_IPIXR_RFULL_MASK 0x00000008 /* Read FIFO Full */
+#define XHI_IPIXR_WEMPTY_MASK 0x00000004 /* Write FIFO Empty */
+#define XHI_IPIXR_RDP_MASK 0x00000002 /* Read FIFO half full */
+#define XHI_IPIXR_WRP_MASK 0x00000001 /* Write FIFO half full */
+#define XHI_IPIXR_ALL_MASK 0x0000000F /* Mask of all interrupts */
+
+/* Control Register (CR) */
+#define XHI_CR_SW_RESET_MASK 0x00000008 /* SW Reset Mask */
+#define XHI_CR_FIFO_CLR_MASK 0x00000004 /* FIFO Clear Mask */
+#define XHI_CR_READ_MASK 0x00000002 /* Read from ICAP to FIFO */
+#define XHI_CR_WRITE_MASK 0x00000001 /* Write from FIFO to ICAP */
+
+/* Status Register (SR) */
+#define XHI_SR_CFGERR_N_MASK 0x00000100 /* Config Error Mask */
+#define XHI_SR_DALIGN_MASK 0x00000080 /* Data Alignment Mask */
+#define XHI_SR_RIP_MASK 0x00000040 /* Read back Mask */
+#define XHI_SR_IN_ABORT_N_MASK 0x00000020 /* Select Map Abort Mask */
+#define XHI_SR_DONE_MASK 0x00000001 /* Done bit Mask  */
+
+
+#define XHI_WFO_MAX_VACANCY 1024 /* Max Write FIFO Vacancy, in words */
+#define XHI_RFO_MAX_OCCUPANCY 256 /* Max Read FIFO Occupancy, in words */
+/* The maximum amount we can request from fifo_icap_get_configuration
+   at once, in bytes. */
+#define XHI_MAX_READ_TRANSACTION_WORDS 0xFFF
+
+
+/**
+ * fifo_icap_fifo_write: Write data to the write FIFO.
+ * @parameter drvdata: a pointer to the drvdata.
+ * @parameter data: the 32-bit value to be written to the FIFO.
+ *
+ * This function will silently fail if the fifo is full.
+ **/
+static inline void fifo_icap_fifo_write(struct hwicap_drvdata *drvdata,
+		u32 data)
+{
+	dev_dbg(drvdata->dev, "fifo_write: %x\n", data);
+	out_be32(drvdata->base_address + XHI_WF_OFFSET, data);
+}
+
+/**
+ * fifo_icap_fifo_read: Read data from the Read FIFO.
+ * @parameter drvdata: a pointer to the drvdata.
+ *
+ * This function will silently fail if the fifo is empty.
+ **/
+static inline u32 fifo_icap_fifo_read(struct hwicap_drvdata *drvdata)
+{
+	u32 data = in_be32(drvdata->base_address + XHI_RF_OFFSET);
+	dev_dbg(drvdata->dev, "fifo_read: %x\n", data);
+	return data;
+}
+
+/**
+ * fifo_icap_set_read_size: Set the the size register.
+ * @parameter drvdata: a pointer to the drvdata.
+ * @parameter data: the size of the following read transaction, in words.
+ **/
+static inline void fifo_icap_set_read_size(struct hwicap_drvdata *drvdata,
+		u32 data)
+{
+	out_be32(drvdata->base_address + XHI_SZ_OFFSET, data);
+}
+
+/**
+ * fifo_icap_start_config: Initiate a configuration (write) to the device.
+ * @parameter drvdata: a pointer to the drvdata.
+ **/
+static inline void fifo_icap_start_config(struct hwicap_drvdata *drvdata)
+{
+	out_be32(drvdata->base_address + XHI_CR_OFFSET, XHI_CR_WRITE_MASK);
+	dev_dbg(drvdata->dev, "configuration started\n");
+}
+
+/**
+ * fifo_icap_start_readback: Initiate a readback from the device.
+ * @parameter drvdata: a pointer to the drvdata.
+ **/
+static inline void fifo_icap_start_readback(struct hwicap_drvdata *drvdata)
+{
+	out_be32(drvdata->base_address + XHI_CR_OFFSET, XHI_CR_READ_MASK);
+	dev_dbg(drvdata->dev, "readback started\n");
+}
+
+/**
+ * fifo_icap_busy: Return true if the ICAP is still processing a transaction.
+ * @parameter drvdata: a pointer to the drvdata.
+ **/
+static inline u32 fifo_icap_busy(struct hwicap_drvdata *drvdata)
+{
+	u32 status = in_be32(drvdata->base_address + XHI_SR_OFFSET);
+	dev_dbg(drvdata->dev, "Getting status = %x\n", status);
+	return (status & XHI_SR_DONE_MASK) ? 0 : 1;
+}
+
+/**
+ * fifo_icap_write_fifo_vacancy: Query the write fifo available space.
+ * @parameter drvdata: a pointer to the drvdata.
+ *
+ * Return the number of words that can be safely pushed into the write fifo.
+ **/
+static inline u32 fifo_icap_write_fifo_vacancy(
+		struct hwicap_drvdata *drvdata)
+{
+	return in_be32(drvdata->base_address + XHI_WFV_OFFSET);
+}
+
+/**
+ * fifo_icap_read_fifo_occupancy: Query the read fifo available data.
+ * @parameter drvdata: a pointer to the drvdata.
+ *
+ * Return the number of words that can be safely read from the read fifo.
+ **/
+static inline u32 fifo_icap_read_fifo_occupancy(
+		struct hwicap_drvdata *drvdata)
+{
+	return in_be32(drvdata->base_address + XHI_RFO_